AGC register 35, 37 override for the low gain setting should only be done
on 5 GHz. Also, 2.4 GHz needs a different value for register 35
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use the correct variable in the check. Fixes an uninitialized variable warning
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Fixes: c8846e1015 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Full tx blocking (as opposed to CCA blocking) should only happen if there
is a continuous non-802.11 signal above the energy detect threshold.
Unfortunately the ED/CCA counter can't detect that, as it also counts 802.11
signals as busy.
Similar to the vendor code, implement a learning mode that waits until the AGC
gain has already been adjusted to the lowest value (due to false CCA events),
and the number of false CCA events still remains high, and the blocking
threshold is exceeded for more than 5 seconds.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Also update the mask first before calculating the vif index.
Fixes an issue where adding back the same interfaces in a different order
fails because of duplicate vif index use
Fixes: 06662264ce ("mt76x02: use mask for vifs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we add txwi at the begining of skb->data, it no longer point
to ieee80211_hdr. This breaks settings TS bit for probe response and
beacons.
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_queue stopped parameter in order to run
ieee80211_wake_queue only when mac80211 queues have been
previously stopped and avoid to disable interrupts when
it is not necessary
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The call to of_find_node_by_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/wireless/mediatek/mt76/eeprom.c:58:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:61:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:67:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:70:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:72:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is for a newer generation of 2x2 MediaTek 802.11n chipsets.
MT7603E is a PCIe chip.
MT7628 and MT7688 are MIPS SoC devices with built-in WLAN.
MT7688 is limited to 1x1
This driver fully supports AP, station, mesh, ad-hoc and monitor mode.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove following routine declarations that are no longer used
after commit cfca5f693c5d ("mt76usb: remove usb_mcu.c"):
- mt76u_mcu_complete_urb
- mt76u_deinit
- mt76u_buf_free
- mt76u_submit_urb
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
check nsgs value is less than urb->num_sgs in mt76u_process_rx_entry
in order to avoid an out-of-bound access of urb->sg array
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use skb_to_sgvec instad of skb_to_sgvec_nomark in mt76u_tx_build_sg.
Remove nsgs check in mt76u_tx_build_sg since it is already performed
by skb_to_sgvec
Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Squash mt76u_buf_alloc_sg and mt76u_buf_alloc and remove duplicated
code. Reuse mt76u_refill_rx in mt76u_buf_alloc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76u_fill_bulk_urb to initialize tx/rx urbs and
remove duplicate code
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix following static checker warning in mt76u_buf_free:
drivers/net/wireless/mediatek/mt76/usb.c:372 mt76u_buf_free()
warn: address of 'urb->sg[i]' is non-NULL
There is no need to check sg page pointer since urb->num_sgs
has been already validated in mt76u_fill_rx_sg
Fixes: cb83585e11 ("mt76: usb: fix possible memory leak in mt76u_buf_free")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use usb_bulk_msg for reading MCU command responses. This simplify code
a lot.
Together with 97a3005759c ("mt76usb: allow mt76u_bulk_msg be used
for reads") it also fix possible problems with rx data buffers
not being aligned and contained within single page. After doing
page_frag_alloc(1024) consecutive page_frag_alloc(PAGE_SIZE) will
alloc PAGE_SIZE buffer at PAGE_SIZE - 1024 offset.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend mt76u_bulk_msg() such it can be used for synchronous bulk reads.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It needs to be always enabled for 76x2 and conditionally enabled/disabled
for 76x0. Since mt76x2_mac_stop clears this bit, ensure that it is enabled
in mt76x02_edcca_init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ED/CCA needs to be disable before stopping the MAC to avoid hangs from tx
being blocked. It must only be enabled again after the MAC has been started
again.
In many places this wasn't done properly, so fix this by always clearing
the relevant ED/CCA bits in mt76x2_mac_stop and set it up again after
channel change or calibration is done
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MCU request timeout usually indicates that the device is no longer responsive,
and it usually does not recover without a reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the timer is already running, there is no need to reset the counter,
because the drift will remain the same.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When mt76x0 and mt76x2 beacon code was unified, it changed the order in which
beacon enable and beacon interval are configured.
Configuring beacon enable before beacon interval can in some cases cause
problems with the beacon timer, leading to clients not waking up properly
from powersave mode.
Fix this by changing the order back to interval first, then enable.
Fixes: cc726268e4 ("mt76: move mt76x02_bss_info_changed in mt76x02-lib module")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check the count before incrementing it to match vendor code behavior.
This defers the adjustment by one more tick, which should improve accuracy
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT_BEACON_TIME_CFG_SYNC_MODE needs to be set for AP mode, according to the
documentation. For other modes it should be irrelevant in this case.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It needs to be unset instead of set
Fixes: 2340523646 ("mt76: fix transmission of encrypted management frames")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since ccmp_pn is u8 *, the second half needs to start at array index 4
instead of 0. Fixes a connection stall after a certain amount of traffic
Fixes: 2340523646 ("mt76: fix transmission of encrypted management frames")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove bogus check for MT_PACKET_ID_NO_ACK in mt76_tx_status_skb_get, which
is already handled in callers and turns timeout calls into no-ops
Do not clean up pending status items on reordering of tx status information
if the timeout is not reached yet
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76_init_stream_cap() and mt76_get_txpower() call __sw_hweight8()
directly, but that's only defined if CONFIG_GENERIC_HWEIGHT is
enabled. The function that works on all architectures is hweight8().
Fixes: 551e1ef4d2 ("mt76: add mt76_init_stream_cap routine")
Fixes: 9313faacbb ("mt76: move mt76x02_get_txpower to mt76 core")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In mt76x02u_skb_dma_info() pad is always non-zero. Patch removes
bogus check and add comments to the function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
During device removal the driver can report multiple error messages.
Use dev_err_ratelimited instead of dev_err to display urb errors
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add disable_usb_sg module parameter to disable scatter-gather on demand
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use linear fragment and not a single usb scatter-gather buffer in mt76u
{tx,rx} datapath if the usb controller has sg data length constraints
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not use scatter-gather buffers for mcu commands.
Introduce mt76u_buf_alloc and mt76u_buf_alloc_sg routines.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76u_check_sg routine in usb.c and introduce sg_en variable
in mt76_usb in order to check if scatter-gather is supported by
mt76u layer
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move q->ndesc initialization before the for loop in mt76u_alloc_rx
since otherwise allocated urbs will not be freed in mt76u_buf_free
Double-check scatterlist pointer in mt76u_buf_free
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix possible NULL pointer dereference in mt76u_mcu_deinit routine that
can occur if initialization path fails before calling mt76u_mcu_init_rx
Fixes: ee676cd501 ("mt76: add driver code for MT76x2u based devices")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We don't need to send firmware data asynchronously, much simpler is just
use synchronous usb_bulk_msg().
Tested-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0_init_txpower in order to initialize max_power per channel
at device bootstrap. Modify mt76x0_get_tx_power_per_rate and
mt76x0_get_power_info signature in order to compute tx power for
non-operating channels
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize target_power variable in mt76x0_phy_set_txpower in order to
report target_power in debugfs
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is no need to retun 0 in mt76_dma_attach(), so switch it to void.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x2_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x2_probe
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x0u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x0u_probe and in mt76x0e_probe
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x2u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x2u_probe
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x{0,2} alloc_device common code in mt76_alloc_device and
remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Block only when the busy time reaches 92%, as lower values can be reached with
heavy 802.11 traffic as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Based on system load and time needed by other calibration runs, the time
between dev->mac_work runs can vary quite a bit.
Calculate busy time based on the actual time difference in order to avoid
potentially over-estimating busy time, which could lead to unnecessary tx
blocking.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ED/CCA Tx blocking checks need to be run every 100 ms in order to avoid
triggering too late and keeping tx blocking on for too long
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Software encrypted packets can be passed not just through the drv_tx callback,
but also through the intermediate tx queue.
In order to deal with that, move the override to mt76x02_mac_write_txwi and
also take care of filling in the per-packet rate information
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove add_buf function pointer in mt76_queue_ops data structure since
it is no longer used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_dma_tx_queue_skb_raw routine in dma.c and add the
corresponding entry in mt76_queue_ops data structure.
mt76_dma_tx_queue_skb_raw will be reused adding support for
mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove useless commented out configuration in mt76x0u_load_firmware
routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_rx_event i mt76-core module and remove duplicated code.
mt76_mcu_rx_event will be reused adding support for mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_get_response in mt76-core module and remove duplicated
code. mt76_mcu_get_response will be reused adding support for mt7603
driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_msg_alloc in mt76-core module and remove duplicated code.
mt76_mcu_msg_alloc will be reused adding support for mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix rate power configuration for VHT mcs 8 and 9 in
mt76x0_get_tx_power_per_rate. Moreover use the rate power
offset used for HT/VHT mcs 6 even for HT/VHT mcs 7
Fixes: b37bbc8c82 ("mt76x0: remove eeprom dependency from mt76x0_set_tx_power_per_rate")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we implement beconing on USB now, similar interfaces should be
supported for USB as are for MMIO. Tested only on IBSS mode and
AP mode (not enabled due to lack of PS buffering).
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure beaconing on USB devices without PS buffering support.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Disable BEACON timer during init and configure interrupt registers
only for mmio devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
BSSID is not strtirct related with beaconing (for example we can have
2 STA vifs) and more related with MAC address, so initaize BSSID when
setting MAC address.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we now support mt76x2u feature to allow set mac address
when creating interface in common code we can use it for
mt76x2u.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use vif_mask to count interfaces to allow to set mac address in HW
if there is only one interface and report error if we create
interface with wrong BSSID resulting in already used index.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The series "[PATCH 0/2] mt76x0: initialize per-channel max_power" depends on
commit d04ca38386 ("mt76x0u: fix suspend/resume"), so merge wireless-drivers
into wireless-drivers-next to get that.
We need to reset MCU and do other initializations on resume otherwise
MT7610U device will fail to initialize, what cause system hung due to
USB requests timeouts.
Patch fixes 4.19 -> 4.20 regression.
Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Substitute WARN_ON with WARN_ON_ONCE in mt7601u_rx_next_seg_len
routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Report correct eeprom per channel power value.
Fix chan_vs_power map in mt76x0_get_power_info routine
Fixes: f2a2e819d6 ("mt76x0: remove eeprom dependency from mt76x0_get_power_info")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case a tx queue wake call arrives after a client has transitioned to
powersave, make sure that the queue is not kept active until the client
has left powersave mode
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Take into account device rx stream in mt76x02_mac_process_rate
in order to not report wrong number of rx spatial stream to mac80211.
The issue has been reported on mt76x0 device which is 1x1:1 however
the hw sometimes reports rx nss equal to 2
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The generic EWMA code cannot deal with negative numbers, so convert signal
to a positive number before adding it
Fixes mt76x2 AGC tuning
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The hardware does not deal with multiple WCID entries for the same station
properly. Set IEEE80211_HW_NEEDS_UNIQUE_STA_ADDR to avoid those cases
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On MT76x2, the hardware does not report tx status in the FIFO register,
if the packet id is 0.
Change the allocation of packet IDs to use 0 for no-ack packets, 1 for
non-probing packets and 2-255 for packets with tx status requested.
Fixes rate control issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02 led support in mt76x02-lib module in order to
add tpt led trigger to mt76x0e driver
Tested-by: LGA1150 <dqfext@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use proper name for __MT76x02_H macro in mt76x02.h
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Call mt76_dma_add_buf routine directly in mt76_dma_tx_queue_skb
and avoid indirect call if not necessary
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Don't populate the const array 'data' on the stack but instead
make it static. Makes the object code smaller by 78 bytes:
Before:
text data bss dec hex filename
5438 1080 0 6518 1976 mediatek/mt76/mt76x2/usb_mcu.o
After:
text data bss dec hex filename
5296 1144 0 6440 1928 mediatek/mt76/mt76x2/usb_mcu.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Port mt76x02_check_tx_hang watchdog from vendor driver in order to
perform a device reset when tx mac/dma logic hangs. Tx mac/dma stuck
has been observed when the device is heavy loaded or in a noisy
environment. Moreover introduce wdt delayed work in order to run
tx_hang watchdog. For the moment run mt76x02_check_tx_hang watchdog
just on mt76x2 devices since the issue has not been observed on mt76x0
driver yet
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Precompute data length in order to avoid to allocate the related
skb data structure if reported length does not fit in queue buf_size
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not set bw variable to zero for legacy rates since it is already
initialized to zero. Moreover set nss to 1 just for legacy rates
since nss will be properly set for VHT/HT rates
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ported from the reference driver. Should fix compliance with ETSI
regulatories on preventing transmission while energy detect values
are above the threshold.
The code has been tested using an ath9k device running tx99 as
noise generator
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update default value for MT_TX_LINK_CFG according to vendor driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Grab mt76_dev mutex in mt76x02_dfs_set_domain since it runs
concurrently with mt76x{0,2}_set_channel routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add static qualifier to mt76x2_init_hardware routine since it is
used just in pci_init.c
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure MT_VHT_HT_FBK_CFG1 values similar like vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure protection based on information that are provided to
us either by remote AP or by hostapd via HT operation IE.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On new mt76 chips, phy mode is configured by last 3 bits
of rate value. Hence OFDM bit is marked by 0x2000
instead of 0x4000.
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use set_rts_threshold calback to enable/disable threshold only for
legacy traffic.
Protection for HT and VHT traffic is defined by HT operation element
and it's provided by remote AP or by hostapd.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As already done for pcie code in commit 79d1c94c9c ("mt76: avoid
queue/status spinlocks while passing tx status to mac80211") make sure
that no tx related spinlocks are taken during the ieee80211_tx_status call
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Grab mt76_dev mutex in mt76x02_mac_work handler since it runs
concurrently with mt76x{0,2}_set_channel routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reconfigure properly MT_MAC_SYS_CTRL register after mac sw-reset
in mt76x02_check_mac_err routine
Fixes: 73556561ab ("mt76x0: use mt76x02_mac_work as stats handler")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MODULE_FIRMWARE() is used in usb_mcu.c and provided by linux/module.h,
but this header file is not directly included. This causes problems in
backports with some kernel versions.
Add the missing include.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Precompute data length in order to avoid to allocate the related
skb data structure if reported length does not fit in queue buf_size
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove napi from mt76_dma_rx_fill routine signature since
it is a leftover of a previous implementation and it is no
longer used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
So far the code only validates the buffer size of the first skb.
Extend this check to cover additional fragments as well, in case the size
is corrupted during a DMA reset.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from mac80211 commit adf8ed01e4 ("mac80211: add an optional
TXQ for other PS-buffered frames") and commit 0eeb2b674f ("mac80211:
add an option for station management TXQ") a new per-sta queue has been
introduced for bufferable management frames.
sta->txq[IEEE80211_NUM_TIDS] is initialized just if the driver reports
the following hw flags:
- IEEE80211_HW_STA_MMPDU_TXQ
- IEEE80211_HW_BUFF_MMPDU_TXQ
This can produce a NULL pointer dereference in mt76_stop_tx_queues
since mt76 iterates on all available sta tx queues assuming they are
initialized by mac80211. This issue has been spotted analyzing the code
(it has not triggered any crash yet)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* use the same firmware for mt76x2e and mt76x2u
* mt76x2 fixes
* mt76x0 fixes
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAlwBH4oACgkQ130UHQKnbvUdQwCdFL9rDWnaX1nvSwLZrp3DC7qD
CywAoJaygMHs0YVmXWHQ9tdEAY5i4VAO
=qF8w
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2018-11-30' of https://github.com/nbd168/wireless
first batch of mt76 patches for 4.21
* use the same firmware for mt76x2e and mt76x2u
* mt76x2 fixes
* mt76x0 fixes
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
kvalo: fixed a conflict in drivers/net/wireless/mediatek/mt76/mt76x2/pci_main.c
and a build problem in drivers/net/wireless/mediatek/mt76/mt76x02_util.c
Allows adding unassociated stations from mac80211
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
If there are still pending packets in the tx queue when removing a station,
it could possibly lead to a call to further attempts to pull packets from
the mac80211 tx queue after it has already been removed from the scheduling
list.
Prevent this from happening by calling synchronize_rcu after deleting the
wcid pointer before further cleaning up the tx queues.
To be extra careful, ensure that mtxq->list is always initialized properly.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is some code in the mac80211 tx status processing code that could
potentially call back into the tx codepath.
To avoid deadlocks, make sure that no tx related spinlocks are taken
during the ieee80211_tx_status call.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We always wait for CMD_CALIBRATION_OP mcu message, but wait argument is used
for do additional MT_MCU_COM_REG0 register operations, which are needed
for mt76x2e devices and we can use appropriate check instead of wait argument.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x2u_init_beacon_offsets routine since the driver supports
just STA mode
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize bss_info_changed mac80211 callback to
mt76x02_bss_info_changed utility routine and remove duplicated code.
Use 8 as WCID index for sta interface
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Perform channel calibration after each channel switch and not only after
connection establishment since NetworkManager perform multiple frequency
scanning if RSSI in lower a given threshold
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add MCU_CAL_TX_SHAPING calibration in mt76x2u_phy_channel_calibrate
routine since now mt76x2 and mt76x2u driver run the same firmware
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable VHT tx rates in ad-hoc mode for mt76x0e driver.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x02_config_mac_addr_list routine in order to set
the mac address list supported by the driver. Initialize
wiphy->addresses/n_addresses for mt76x0e driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix IBI_R11 configuration on non-radar channels for mt76x0e
driver. This patch improve system stability under heavy load.
Moreover use IBI_R11 name and remove magic numbers for
0x212c register
Fixes: 0c3b3abc9251 ("mt76x0: pci: add DFS support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Assure that after we initialize dev->cal.low_gain to -1 this
will cause update gain calibration. Otherwise this might or
might not happen depending on value of second bit of low_gain
and values read from registers in mt76x02_phy_adjust_vga_gain().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If we are associated and scanning is performed, sw_scan_complete callback
is done after we get back to operating channel, so we do not perform
queue cal work. Fix this queue cal work from sw_scan_complete().
On mt76x0 we have to restore gain in MT_BBP(AGC, 8) register after
scanning, as it was multiple times modified by channel switch code.
So queue cal work without any delay to set AGC gain value.
Similar like in mt76x2 init AGC gain only when set operating channel
and just check before queuing cal work in sw_scan_complete() if
initialization was already done.
Fixes: bbd10586f0 ("mt76x0: phy: do not run calibration during channel switch")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove wait argument from mt76x02_mcu_set_radio_state and newer wait
for response when sending CMD_POWER_SAVING_OP mcu command.
Note this change behaviour for PCIe devices, but the change is in
align with vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove wait argument from mt76x02_mcu_function_select and wait for
response when function is not Q_SELECT, what is the same behaviour
like in vendor driver.
Note this change behaviour for PCIe devices for Q_SELECT function
form wait to no-wait, and for mt76x0u BW_SETTING from no-wait to wait.
But the change is in align with vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We almost always use patter like this:
skb = mt76_mcu_msg_alloc(dev, &msg, sizeof(msg));
return mt76_mcu_send_msg(dev, skb, CMD_FUN_SET_OP, wait_resp);
This is not needed, we can allocate skb in mcu_send_msg routine.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We use always 1 as band parameter for MCU_CAL_LC, this break 2GHz,
we should use 0 for this band instead.
Patch fixes problems happened sometimes when try to associate with 2GHz
AP and manifest by errors like below:
[14680.920823] wlan0: authenticate with 18:31:bf:c0:51:b0
[14681.109506] wlan0: send auth to 18:31:bf:c0:51:b0 (try 1/3)
[14681.310454] wlan0: send auth to 18:31:bf:c0:51:b0 (try 2/3)
[14681.518469] wlan0: send auth to 18:31:bf:c0:51:b0 (try 3/3)
[14681.726499] wlan0: authentication with 18:31:bf:c0:51:b0 timed out
Fixes: 9aec146d0f ("mt76x0: pci: introduce mt76x0_phy_calirate routine")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use tssi calibrated value to configure tx power gain if tssi is enabled
in eeprom data
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt76x0 tssi calibration process if enabled in eeprom data.
Perform calibration procedure every 4s
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_eeprom_copy utility routine in mt76x02-lib module
in order to be reused by mt76x0 driver adding tssi calibration
support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_mac_wcid_setup and mt76x02_mac_shared_key_setup for
shared keys and wcid table initialization and remove duplicated
code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove MT_TSO_CTRL and MT_HEADER_TRANS_CTRL_REG initialization since
it is already done in mt76_write_mac_initvals routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_mac_wcid_setup utility routine for wcid init configuration
and remove duplicated code. This patch fixes a mt76x0 AP issue since
hw key table selection was set to pairwise by default
Fixes: dbad2adcb2c7 ("mt76x0: pci: enable AP support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move WCID tx rate configuration at device bootstrap since
the related register are always set to 0
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_mac_shared_key_setup utility routine for shared key
initialization and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76_poll_msec utility routine for CORE_R34 register polling
instead of mt76_poll in order to allow the hw to complete requested
calibration since on slow devices (e.g. mt7620 based boards) calibration
takes longer than 2ms
Fixes: 66a34c66e0 ("mt76x0: phy: add phy/vco temperature compensation")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT_BBP(AGC, 8) register has values depend on band in
mt76x0_bbp_switch_tab, so we should not overwrite other fields
than MT_BBP_AGC_GAIN when setting gain.
This can fix performance issues when connecting to 2.4GHz AP.
Fixes: 4636a2544c ("mt76x0: phy: align channel gain logic to mt76x2 one")
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT76x2/MT76x0 has somewhat unreliable tx status reporting, and for that
reason the driver currently does not report per-skb tx ack status at all.
This breaks things like client idle polling, which relies on the tx ack
status of a transmitted nullfunc frame.
This patch adds code to report skb-attached tx status if requested by
mac80211 or the rate control module. Since tx status is polled from a
simple FIFO register, the code needs to account for the possibility of
tx status events getting lost.
The code keeps a list of skbs for which tx status is required and passes
them to mac80211 once tx status has been filled in and the DMA queue is
done with it.
If a tx status event is not received after one second, the status rates
are cleared, and a succesful ACK is indicated to avoid spurious disassoc
during assoc or client polling.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau