When Broadcom SDIO cards are idled they go to sleep and a whole
separate subsystem takes over their SDIO communication. This is the
Always-On-Subsystem (AOS) and it can't handle tuning requests.
Specifically, as tested on rk3288-veyron-minnie (which reports having
BCM4354/1 in dmesg), if I force a retune in brcmf_sdio_kso_control()
when "on = 1" (aka we're transition from sleep to wake) by whacking:
bus->sdiodev->func1->card->host->need_retune = 1
...then I can often see tuning fail. In this case dw_mmc reports "All
phases bad!"). Note that I don't get 100% failure, presumably because
sometimes the card itself has already transitioned away from the AOS
itself by the time we try to wake it up. If I force retuning when "on
= 0" (AKA force retuning right before sending the command to go to
sleep) then retuning is always OK.
NOTE: we need _both_ this patch and the patch to avoid triggering
tuning due to CRC errors in the sleep/wake transition, AKA ("brcmfmac:
sdio: Disable auto-tuning around commands expected to fail"). Though
both patches handle issues with Broadcom's AOS, the problems are
distinct:
1. We want to defer (but not ignore) asynchronous (like
timer-requested) tuning requests till the card is awake. However,
we want to ignore CRC errors during the transition, we don't want
to queue deferred tuning request.
2. You could imagine that the AOS could implement retuning but we
could still get errors while transitioning in and out of the AOS.
Similarly you could imagine a seamless transition into and out of
the AOS (with no CRC errors) even if the AOS couldn't handle
tuning.
ALSO NOTE: presumably there is never a desperate need to retune in
order to wake up the card, since doing so is impossible. Luckily the
only way the card can get into sleep state is if we had a good enough
tuning to send it the command to put it into sleep, so presumably that
"good enough" tuning is enough to wake us up, at least with a few
retries.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are certain cases, notably when transitioning between sleep and
active state, when Broadcom SDIO WiFi cards will produce errors on the
SDIO bus. This is evident from the source code where you can see that
we try commands in a loop until we either get success or we've tried
too many times. The comment in the code reinforces this by saying
"just one write attempt may fail"
Unfortunately these failures sometimes end up causing an "-EILSEQ"
back to the core which triggers a retuning of the SDIO card and that
blocks all traffic to the card until it's done.
Let's disable retuning around the commands we expect might fail.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 29f6589140.
After that patch landed I find that my kernel log on
rk3288-veyron-minnie and rk3288-veyron-speedy is filled with:
brcmfmac: brcmf_sdio_bus_sleep: error while changing bus sleep state -110
This seems to happen every time the Broadcom WiFi transitions out of
sleep mode. Reverting the commit fixes the problem for me, so that's
what this patch does.
Note that, in general, the justification in the original commit seemed
a little weak. It looked like someone was testing on a SD card
controller that would sometimes die if there were CRC errors on the
bus. This used to happen back in early days of dw_mmc (the controller
on my boards), but we fixed it. Disabling a feature on all boards
just because one SD card controller is broken seems bad.
Fixes: 29f6589140 ("brcmfmac: disable command decode in sdio_aos")
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Double Lo <double.lo@cypress.com>
Cc: Madhan Mohan R <madhanmohan.r@cypress.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program see the file copying if not write to the free
software foundation inc 51 franklin steet fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 41 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.524645346@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Normally firmware messages are printed with debugging enabled only. It's
a good idea as firmware may print a lot of messages that normal users
don't need to care about.
However, on firmware crash, it may be very helpful to log all recent
messages. There is almost always a backtrace available as well as rought
info on the latest actions/state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some PCIE firmwares drop txstatus if pktid is 0 and make packet held in
host side and never be released. If that packet type is 802.1x, the
pend_8021x_cnt value will be always greater than 0 and show "Timed out
waiting for no pending 802.1x packets" error message when sending key to
dongle every time.
To be compatible with all firmwares, host should set txflow request id
from 1 instead of from 0.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If "ret_len" is negative then it could lead to a NULL dereference.
The "ret_len" value comes from nl80211_vendor_cmd(), if it's negative
then we don't allocate the "dcmd_buf" buffer. Then we pass "ret_len" to
brcmf_fil_cmd_data_set() where it is cast to a very high u32 value.
Most of the functions in that call tree check whether the buffer we pass
is NULL but there are at least a couple places which don't such as
brcmf_dbg_hex_dump() and brcmf_msgbuf_query_dcmd(). We memcpy() to and
from the buffer so it would result in a NULL dereference.
The fix is to change the types so that "ret_len" can't be negative. (If
we memcpy() zero bytes to NULL, that's a no-op and doesn't cause an
issue).
Fixes: 1bacb0487d ("brcmfmac: replace cfg80211 testmode with vendor command")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For PCIE wireless device with core revision less than 14, device may miss
PCIE to System Backplane Interrupt via PCIEtoSBMailbox. So add sending
mail box interrupt twice as a hardware workaround.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 99d94ef367. I accidentally
applied this broken (failed to compile) patch due to a bug in my patchwork
script.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For PCIE wireless device with core revision less than 14, device may miss
PCIE to System Backplane Interrupt via PCIEtoSBMailbox. So add sending
mail box interrupt twice as a hardware workaround.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ACEPC T8 and T11 mini PCs contain quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.Default string-Default string.txt" as nvram file which
is way too generic.
The DMI strings on which we are matching are somewhat generic too, but
"To be filled by O.E.M." is less common then "Default string" and the
system-sku and bios-version strings are pretty unique. Beside the DMI
strings we also check the wifi-module chip-id and revision. I'm confident
that the combination of all this is unique.
Both the T8 and T11 use the same wifi-module, this commit adds DMI
quirks for both mini PCs pointing to brcmfmac43455-sdio.acepc-t8.txt .
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1690852
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit d825db346270e ("b43: shut up clang -Wuninitialized variable
warning"), the message noted that function lpphy_papd_cal() was empty
and had an old TODO regarding its implementation. As the reverse
engineering project that created the LP-PHY version of this driver
has not been active for some time, it is safe to remove this empty
function.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently if the call to brcmf_sdiod_set_backplane_window fails then
error return path leaks mypkt. Fix this by returning by a new
error path labelled 'out' that calls brcmu_pkt_buf_free_skb to free
mypkt. Also remove redundant check on err before calling
brcmf_sdiod_skbuff_write.
Addresses-Coverity: ("Resource Leak")
Fixes: a7c3aa1509 ("brcmfmac: Remove brcmf_sdiod_addrprep()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO based brcm43456 is currently misdetected as brcm43455 and the wrong
firmware name is used. Correct the detection and load the correct
firmware file. Chiprev for brcm43456 is "9".
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable reqsz is not necessary,
hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Clang warns about what is clearly a case of passing an uninitalized
variable into a static function:
drivers/net/wireless/broadcom/b43/phy_lp.c:1852:23: error: variable 'gains' is uninitialized when used here
[-Werror,-Wuninitialized]
lpphy_papd_cal(dev, gains, 0, 1, 30);
^~~~~
drivers/net/wireless/broadcom/b43/phy_lp.c:1838:2: note: variable 'gains' is declared here
struct lpphy_tx_gains gains, oldgains;
^
1 error generated.
However, this function is empty, and its arguments are never evaluated,
so gcc in contrast does not warn here. Both compilers behave in a
reasonable way as far as I can tell, so we should change the code
to avoid the warning everywhere.
We could just eliminate the lpphy_papd_cal() function entirely,
given that it has had the TODO comment in it for 10 years now
and is rather unlikely to ever get done. I'm doing a simpler
change here, and just pass the 'oldgains' variable in that has
been initialized, based on the guess that this is what was
originally meant.
Fixes: 2c0d6100da ("b43: LP-PHY: Begin implementing calibration & software RFKILL support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case kmemdup fails, the fix sets conn_info->req_ie_len and
conn_info->resp_ie_len to zero to avoid buffer overflows.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_usb_free_q is no longer called with pending=true thus this boolean
parameter is no longer needed.
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It was observed that rarely during USB disconnect happening shortly after
connect (before full initialization completes) usb_hub_wq would wait
forever for the dev_init_lock to be unlocked. dev_init_lock would remain
locked though because of infinite wait during usb_kill_urb:
[ 2730.656472] kworker/0:2 D 0 260 2 0x00000000
[ 2730.660700] Workqueue: events request_firmware_work_func
[ 2730.664807] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac)
[ 2730.670587] [<809dd164>] (schedule) from [<8069af44>] (usb_kill_urb+0xdc/0x114)
[ 2730.676815] [<8069af44>] (usb_kill_urb) from [<7f258b50>] (brcmf_usb_free_q+0x34/0xa8 [brcmfmac])
[ 2730.684833] [<7f258b50>] (brcmf_usb_free_q [brcmfmac]) from [<7f2517d4>] (brcmf_detach+0xa0/0xb8 [brcmfmac])
[ 2730.693557] [<7f2517d4>] (brcmf_detach [brcmfmac]) from [<7f251a34>] (brcmf_attach+0xac/0x3d8 [brcmfmac])
[ 2730.702094] [<7f251a34>] (brcmf_attach [brcmfmac]) from [<7f2587ac>] (brcmf_usb_probe_phase2+0x468/0x4a0 [brcmfmac])
[ 2730.711601] [<7f2587ac>] (brcmf_usb_probe_phase2 [brcmfmac]) from [<7f252888>] (brcmf_fw_request_done+0x194/0x220 [brcmfmac])
[ 2730.721795] [<7f252888>] (brcmf_fw_request_done [brcmfmac]) from [<805748e4>] (request_firmware_work_func+0x4c/0x88)
[ 2730.731125] [<805748e4>] (request_firmware_work_func) from [<80141474>] (process_one_work+0x228/0x808)
[ 2730.739223] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[ 2730.746105] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[ 2730.752227] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
[ 2733.099695] kworker/0:3 D 0 1065 2 0x00000000
[ 2733.103926] Workqueue: usb_hub_wq hub_event
[ 2733.106914] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac)
[ 2733.112693] [<809dd164>] (schedule) from [<809e2a8c>] (schedule_timeout+0x214/0x3e4)
[ 2733.119621] [<809e2a8c>] (schedule_timeout) from [<809dde2c>] (wait_for_common+0xc4/0x1c0)
[ 2733.126810] [<809dde2c>] (wait_for_common) from [<7f258d00>] (brcmf_usb_disconnect+0x1c/0x4c [brcmfmac])
[ 2733.135206] [<7f258d00>] (brcmf_usb_disconnect [brcmfmac]) from [<8069e0c8>] (usb_unbind_interface+0x5c/0x1e4)
[ 2733.143943] [<8069e0c8>] (usb_unbind_interface) from [<8056d3e8>] (device_release_driver_internal+0x164/0x1fc)
[ 2733.152769] [<8056d3e8>] (device_release_driver_internal) from [<8056c078>] (bus_remove_device+0xd0/0xfc)
[ 2733.161138] [<8056c078>] (bus_remove_device) from [<8056977c>] (device_del+0x11c/0x310)
[ 2733.167939] [<8056977c>] (device_del) from [<8069cba8>] (usb_disable_device+0xa0/0x1cc)
[ 2733.174743] [<8069cba8>] (usb_disable_device) from [<8069507c>] (usb_disconnect+0x74/0x1dc)
[ 2733.181823] [<8069507c>] (usb_disconnect) from [<80695e88>] (hub_event+0x478/0xf88)
[ 2733.188278] [<80695e88>] (hub_event) from [<80141474>] (process_one_work+0x228/0x808)
[ 2733.194905] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[ 2733.201724] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[ 2733.207913] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
It was traced down to a case where usb_kill_urb would be called on an URB
structure containing more or less random data, including large number in
its use_count. During the debugging it appeared that in brcmf_usb_free_q()
the traversal over URBs' lists is not synchronized with operations on those
lists in brcmf_usb_rx_complete() leading to handling
brcmf_usbdev_info structure (holding lists' head) as lists' element and in
result causing above problem.
Fix it by walking through all URBs during brcmf_cancel_all_urbs using the
arrays of requests instead of linked lists.
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmu_pkt_buf_free_skb emits WARNING when attempting to free a sk_buff
which is part of any queue. After USB disconnect this may have happened
when brcmf_fws_hanger_cleanup() is called as per-interface psq was never
cleaned when removing the interface.
Change brcmf_fws_macdesc_cleanup() in a way that it removes the
corresponding packets from hanger table (to avoid double-free when
brcmf_fws_hanger_cleanup() is called) and add a call to clean-up the
interface specific packet queue.
Below is a WARNING during USB disconnect with Raspberry Pi WiFi dongle
running in AP mode. This was reproducible when the interface was
transmitting during the disconnect and is fixed with this commit.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1171 at drivers/net/wireless/broadcom/brcm80211/brcmutil/utils.c:49 brcmu_pkt_buf_free_skb+0x3c/0x40
Modules linked in: nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle xt_connmark xt_tcpudp xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter ip_tables x_tables usb_f_mass_storage usb_f_rndis u_ether cdc_acm smsc95xx usbnet ci_hdrc_imx ci_hdrc ulpi usbmisc_imx 8250_exar 8250_pci 8250 8250_base libcomposite configfs udc_core
CPU: 0 PID: 1171 Comm: kworker/0:0 Not tainted 4.19.23-00075-gde33ed8 #99
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: usb_hub_wq hub_event
[<8010ff84>] (unwind_backtrace) from [<8010bb64>] (show_stack+0x10/0x14)
[<8010bb64>] (show_stack) from [<80840278>] (dump_stack+0x88/0x9c)
[<80840278>] (dump_stack) from [<8011f5ec>] (__warn+0xfc/0x114)
[<8011f5ec>] (__warn) from [<8011f71c>] (warn_slowpath_null+0x40/0x48)
[<8011f71c>] (warn_slowpath_null) from [<805a476c>] (brcmu_pkt_buf_free_skb+0x3c/0x40)
[<805a476c>] (brcmu_pkt_buf_free_skb) from [<805bb6c4>] (brcmf_fws_cleanup+0x1e4/0x22c)
[<805bb6c4>] (brcmf_fws_cleanup) from [<805bc854>] (brcmf_fws_del_interface+0x58/0x68)
[<805bc854>] (brcmf_fws_del_interface) from [<805b66ac>] (brcmf_remove_interface+0x40/0x150)
[<805b66ac>] (brcmf_remove_interface) from [<805b6870>] (brcmf_detach+0x6c/0xb0)
[<805b6870>] (brcmf_detach) from [<805bdbb8>] (brcmf_usb_disconnect+0x30/0x4c)
[<805bdbb8>] (brcmf_usb_disconnect) from [<805e5d64>] (usb_unbind_interface+0x5c/0x1e0)
[<805e5d64>] (usb_unbind_interface) from [<804aab10>] (device_release_driver_internal+0x154/0x1ec)
[<804aab10>] (device_release_driver_internal) from [<804a97f4>] (bus_remove_device+0xcc/0xf8)
[<804a97f4>] (bus_remove_device) from [<804a6fc0>] (device_del+0x118/0x308)
[<804a6fc0>] (device_del) from [<805e488c>] (usb_disable_device+0xa0/0x1c8)
[<805e488c>] (usb_disable_device) from [<805dcf98>] (usb_disconnect+0x70/0x1d8)
[<805dcf98>] (usb_disconnect) from [<805ddd84>] (hub_event+0x464/0xf50)
[<805ddd84>] (hub_event) from [<80135a70>] (process_one_work+0x138/0x3f8)
[<80135a70>] (process_one_work) from [<80135d5c>] (worker_thread+0x2c/0x554)
[<80135d5c>] (worker_thread) from [<8013b1a0>] (kthread+0x124/0x154)
[<8013b1a0>] (kthread) from [<801010e8>] (ret_from_fork+0x14/0x2c)
Exception stack(0xecf8dfb0 to 0xecf8dff8)
dfa0: 00000000 00000000 00000000 00000000
dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
dfe0: 00000000 00000000 00000000 00000000 00000013 00000000
---[ end trace 38d234018e9e2a90 ]---
------------[ cut here ]------------
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This includes bus reset & reloading a firmware. It should be sufficient
for a user space to (setup and) use a wireless device again.
Support for reset on USB & SDIO can be added later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This improves handling PCIe firmware halts by printing a clear error
message and replaces a similar code in the SDIO bus support.
It will also allow further improvements like trying to recover from a
firmware crash.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During a normal brcmfmac lifetime brcmf_fw_alloc_request() is called
once only during the probe. It's safe to assume provided array is clear.
Further brcmfmac improvements may require calling it multiple times
though. This patch allows it by fixing invalid firmware paths like:
brcm/brcmfmac4366c-pcie.binbrcm/brcmfmac4366c-pcie.bin
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware may report general errors using a special message type. Add
basic support for it by simply decoding & printing an error number.
A sample situation in which firmware reports a buf error:
CONSOLE: 027084.733 no host response IOCTL buffer available..so fail the request
will now produce a "Firmware reported general error: 9" on the host.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This updates host struct to match the in-firmawre definition. It's a
cosmetic change as it only applies to the reserved struct space.
Fixes: c988b78244 ("brcmfmac: print firmware reported ring status errors")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While experimenting with firmware loading I ended up in a state of
firmware reporting shared RAM address 0x04000001. It was causing:
[ 94.448015] Unable to handle kernel paging request at virtual address cd680001
due to reading out of the mapped memory.
This patch adds some basic validation to avoid kernel crashes due to the
unexpected firmware behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This recently added macro provides more meaningful error messages thanks
to identifying a specific wiphy. It's especially important on systems
with few cards supported by the same (brcmfmac) driver.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c: In function 'brcmf_usb_state_change':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:578:6: warning:
variable 'old_state' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This macro will be used in more places not just the cfg80211.c. It makes
sense to pass some common struct to it as "struct wiphy" is mostly
referenced in cfg80211 code only.
A very common one (used above the bus abstraction layer) is struct
brcmf_pub. Many functions already keep reference to it which will make
using bphy_err() simpler. It should also allow extending that macro's
logic if it's ever needed.
This improves code recently added in the commit 3ef005b82e ("brcmfmac:
add bphy_err() and use it in the cfg80211.c").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far 160 MHz channels were treated as 20 MHz ones which was breaking
support for 40/80 MHz due to the brcmf_construct_chaninfo() logic and
its assumptions.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1) Use switch to simplify/improve the code & avoid some duplication
2) Add warning for unsupported values
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware is capable of reporting ring status. It's used e.g. to signal
some problem with a specific ring setup. This patch adds support for
printing ring & error number which may be useful for debugging setup
issues.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The local variable chipname is string representation of chip id and revision
which is printed in the good flow of brcmf_fw_alloc_request(). Also use it
for the error path, ie. for unknown/unsupported devices.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the firmware crashes during the probe sequence we provide little
information on what really failed. This patch checks the sdpcm shared
location and show the trap information if a firmware trap has happened.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The MBSS feature was already disabled for bcm43362 as it resulted in a
beacon with BRCM_TEST_SSID regardless user configuration in hostapd. Now
the same has been reported for bcm4330 so disable the feature for this
device as well.
Reported-by: Russell King <linux@armlinux.org.uk>
Tested-by: Christopher Martin <chrsmrtn@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since we moved the drivers debugfs directory under ieee80211 debugfs the
debugfs entries need to be added after wiphy_register() has been called.
For most part that has been done accordingly, but for the debugfs entries
added by SDIO it was not and failed silently. This patch fixes that by
adding a bus-layer callback for it.
Fixes: 856d5a011c ("brcmfmac: allocate struct brcmf_pub instance using wiphy_new()")
Reported-by: Russel King <linux@armlinux.org.uk>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For USB there is no separate channel being used to pass events
from firmware to the host driver and as such are passed over the
data path. In order to detect mock event messages an additional
check is needed on event subtype. This check is added conditionally
using unlikely() keyword.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SSID length as received from firmware should not exceed
IEEE80211_MAX_SSID_LEN as that would result in heap overflow.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far there were two monitor frame formats:
1) 802.11 frames (with frame (sub)type & all addresses)
2) 802.11 frames with the radiotap header
Testing the latest FullMAC firmwares for 4366b1/4366c0 resulted in
discovering a new format being used. It seems (almost?) identical to the
one known from ucode used in SoftMAC devices which is most likely the
same codebase anyway.
While new firmwares will /announce/ radiotap header support using the
"rtap" fw capability string it seems no string was added for the new
ucode header format.
All above means that:
1) We need new format support when dealing with a received frame
2) A new feature bit & mapping quirks have to be added manually
As for now only an empty radiotap is being created. Adding support for
extracting some info (band, channel, signal, etc.) is planned for the
future.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix spelling mistakes in brcmfmac: "lenght" -> "length".
The typos are also in the special comment blocks which
translates to documentation.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This new macro uses wiphy_err() which:
1) Should be the best choice with wiphy already created
2) Uses dev_err() which allows identifying error-affected device
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Douglas Anderson