In the current code, it only removes *.o and .*.o.d file when make clean,
there still exists useless .*.o.cmd file, just remove it.
Without this patch:
[yangtiezhu@linux spi]$ make
[yangtiezhu@linux spi]$ make clean
[yangtiezhu@linux spi]$ ls -1 .*.o.cmd
.spidev_fdx-in.o.cmd
.spidev_fdx.o.cmd
.spidev_test-in.o.cmd
.spidev_test.o.cmd
With this patch:
[yangtiezhu@linux spi]$ make
[yangtiezhu@linux spi]$ make clean
[yangtiezhu@linux spi]$ ls -1 .*.o.cmd
ls: cannot access .*.o.cmd: No such file or directory
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/1586230512-5507-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Here are 3 SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your current
tree, that should be trivial to handle (one file modified by two things,
one file deleted.)
All 3 of these have been in linux-next for a while, with no reported
issues other than the merge conflict.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodg5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykySQCgy9YDrkz7nWq6v3Gohl6+lW/L+rMAnRM4uTZm
m5AuCzO3Azt9KBi7NL+L
=2Lm5
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here are three SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your
current tree, that should be trivial to handle (one file modified by
two things, one file deleted.)
All three of these have been in linux-next for a while, with no
reported issues other than the merge conflict"
* tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
ASoC: MT6660: make spdxcheck.py happy
.gitignore: add SPDX License Identifier
.gitignore: remove too obvious comments
In the current code, it only removes "include/linux/spi/spidev.h" file
when make clean and there still exists useless "include/linux/spi/"
directory, just remove it.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/1581567368-8055-4-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
It is better to use perror() only if errno is not 0, it should use printf()
when errno is 0, otherwise there exists redudant ": Success".
E.g. without this patch:
$ ./spidev_test -p 1234 --input test.bin
only one of -p and --input may be selected: Success
Aborted (core dumped)
With this patch:
$ ./spidev_test -p 1234 --input test.bin
only one of -p and --input may be selected
Aborted (core dumped)
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1581567368-8055-3-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
It is better to check input_tx and input_file first after parse options.
Otherwise, it will do some useless operations when both -p and --input
are selected.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1581567368-8055-2-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
When call print_usage() in parse_opts(), it will exit directly.
Since break is not useful after exit statement, remove it.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1581567368-8055-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 24 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.162703968@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Print spaces as spaces,
- Do not print characters > 126, as they will be shown as garbage
in the modern UTF-8 era,
- Use a normal period instead of its hexadecimal ASCII value,
- Delimit the text part with pipe symbols on both sides (was left side
only), without any spaces, to make it clear where the decoded text
starts and ends,
- Drop a useless comment.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently a number of Makefiles break when used with toolchains that
pass extra flags in CC and other cross-compile related variables (such
as --sysroot).
Thus we get this error when we use a toolchain that puts --sysroot in
the CC var:
~/src/linux/tools$ make iio
[snip]
iio_event_monitor.c:18:10: fatal error: unistd.h: No such file or directory
#include <unistd.h>
^~~~~~~~~~
This occurs because we clobber several env vars related to
cross-compiling with lines like this:
CC = $(CROSS_COMPILE)gcc
Although this will point to a valid cross-compiler, we lose any extra
flags that might exist in the CC variable, which can break toolchains
that rely on them (for example, those that use --sysroot).
This easily shows up using a Yocto SDK:
$ . [snip]/sdk/environment-setup-cortexa8hf-neon-poky-linux-gnueabi
$ echo $CC
arm-poky-linux-gnueabi-gcc -march=armv7-a -mfpu=neon -mfloat-abi=hard
-mcpu=cortex-a8
--sysroot=[snip]/sdk/sysroots/cortexa8hf-neon-poky-linux-gnueabi
$ echo $CROSS_COMPILE
arm-poky-linux-gnueabi-
$ echo ${CROSS_COMPILE}gcc
krm-poky-linux-gnueabi-gcc
Although arm-poky-linux-gnueabi-gcc is a cross-compiler, we've lost the
--sysroot and other flags that enable us to find the right libraries to
link against, so we can't find unistd.h and other libraries and headers.
Normally with the --sysroot flag we would find unistd.h in the sdk
directory in the sysroot:
$ find [snip]/sdk/sysroots -path '*/usr/include/unistd.h'
[snip]/sdk/sysroots/cortexa8hf-neon-poky-linux-gnueabi/usr/include/unistd.h
The perf Makefile adds CC = $(CROSS_COMPILE)gcc if and only if CC is not
already set, and it compiles correctly with the above toolchain.
So, generalize the logic that perf uses in the common Makefile and
remove the manual CC = $(CROSS_COMPILE)gcc lines from each Makefile.
Note that this patch does not fix cross-compile for all the tools (some
have other bugs), but it does fix it for all except usb and acpi, which
still have other unrelated issues.
I tested both with and without the patch on native and cross-build and
there appear to be no regressions.
Link: http://lkml.kernel.org/r/20180107214028.23771-1-martin@martingkelly.com
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Pali Rohar <pali.rohar@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a nice buildsystem dedicated for userspace tools in Linux kernel tree.
Switch spi target to be built by it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add option to send+recv <size> bytes with <iter> iterations
and show the transfer rate every 5 seconds.
Example:
rate: tx 4235.2kbps, rx 4235.2kbps
total: tx 4882.8KB, rx 4882.8KB
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check the input file fd instead of spidev fd.
The spidev fd is supposed to be OK otherwise the transfer_file() function
would not be called at all.
Signed-off-by: Michal Vokáč <vokac.m@gmail.com>
Reviewed-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes spidev_test crashes with:
*** Error in `spidev_test': munmap_chunk(): invalid pointer: 0x00022020 ***
Aborted
or just
Segmentation fault
This is due to transfer_escaped_string() miscalculating the required
size of the buffer by one byte, causing a buffer overflow in unescape().
Drop the bogus "+ 1" in the strlen() parameter to fix this.
Note that unescape() never copies the zero-terminator of the source
string, so it writes at most as many bytes as the length of the source
string.
Fixes: 30061915be (spi: spidev_test: Added input buffer from the terminal)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> # v4.5+
spidev.h uses _IOC_SIZEBITS directly. musl libc does not provide this macro
unless linux/ioctl.h is included explicitly. Fixes build failures like:
In file included from .../host/usr/arm-buildroot-linux-musleabihf/sysroot/usr/include/sys/ioctl.h:7:0,
from .../build/spidev_test-v3.15/spidev_test.c:20:
.../build/spidev_test-v3.15/spidev_test.c: In function ‘transfer’:
.../build/spidev_test-v3.15/spidev_test.c:75:18: error: ‘_IOC_SIZEBITS’ undeclared (first use in this function)
ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr);
^
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the spelling of 'output' in the error message.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that spidev_test and spidev_fdx have been moved, remove them
from the Documentation index and move their .gitignore file.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check the result of sscanf to verify a result was found.
report and error and abort if pattern was not found.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For testing of larger data transfers, output unmodified data
directly to a file.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add input file support to facilitate testing larger data.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the input_tx code into its own small function.
This cleans up some variables from main() that are used only here.
While we are at it, check malloc calls instead of assuming they succeed.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jon Corbet requested this code moved with the last changeset,
https://lkml.org/lkml/2015/3/1/144,
but the patch was not applied because it missed the Makefile.
Moved spidev_test, spidev_fdx and their Makefile infrastructure.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geert Uytterhoeven