This patch is based on the upstream commit 5ac1c4bcf0 and amended
for v4.2 to make sure it works as intended.
Repeated calls to begin_crtc_commit can cause warnings like this:
[ 169.127746] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616
[ 169.127835] in_atomic(): 0, irqs_disabled(): 1, pid: 1947, name: kms_flip
[ 169.127840] 3 locks held by kms_flip/1947:
[ 169.127843] #0: (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffff814774bc>] __drm_modeset_lock_all+0x9c/0x130
[ 169.127860] #1: (crtc_ww_class_acquire){+.+.+.}, at: [<ffffffff814774cd>] __drm_modeset_lock_all+0xad/0x130
[ 169.127870] #2: (crtc_ww_class_mutex){+.+.+.}, at: [<ffffffff81477178>] drm_modeset_lock+0x38/0x110
[ 169.127879] irq event stamp: 665690
[ 169.127882] hardirqs last enabled at (665689): [<ffffffff817ffdb5>] _raw_spin_unlock_irqrestore+0x55/0x70
[ 169.127889] hardirqs last disabled at (665690): [<ffffffffc0197a23>] intel_pipe_update_start+0x113/0x5c0 [i915]
[ 169.127936] softirqs last enabled at (665470): [<ffffffff8108a766>] __do_softirq+0x236/0x650
[ 169.127942] softirqs last disabled at (665465): [<ffffffff8108ae75>] irq_exit+0xc5/0xd0
[ 169.127951] CPU: 1 PID: 1947 Comm: kms_flip Not tainted 4.1.0-rc4-patser+ #4039
[ 169.127954] Hardware name: LENOVO 2349AV8/2349AV8, BIOS G1ETA5WW (2.65 ) 04/15/2014
[ 169.127957] ffff8800c49036f0 ffff8800cde5fa28 ffffffff817f6907 0000000080000001
[ 169.127964] 0000000000000000 ffff8800cde5fa58 ffffffff810aebed 0000000000000046
[ 169.127970] ffffffff81c5d518 0000000000000268 0000000000000000 ffff8800cde5fa88
[ 169.127981] Call Trace:
[ 169.127992] [<ffffffff817f6907>] dump_stack+0x4f/0x7b
[ 169.128001] [<ffffffff810aebed>] ___might_sleep+0x16d/0x270
[ 169.128008] [<ffffffff810aed38>] __might_sleep+0x48/0x90
[ 169.128017] [<ffffffff817fc359>] mutex_lock_nested+0x29/0x410
[ 169.128073] [<ffffffffc01635f0>] ? vgpu_write64+0x220/0x220 [i915]
[ 169.128138] [<ffffffffc017fddf>] ? ironlake_update_primary_plane+0x2ff/0x410 [i915]
[ 169.128198] [<ffffffffc0190e75>] intel_frontbuffer_flush+0x25/0x70 [i915]
[ 169.128253] [<ffffffffc01831ac>] intel_finish_crtc_commit+0x4c/0x180 [i915]
[ 169.128279] [<ffffffffc00784ac>] drm_atomic_helper_commit_planes+0x12c/0x240 [drm_kms_helper]
[ 169.128338] [<ffffffffc0184264>] __intel_set_mode+0x684/0x830 [i915]
[ 169.128378] [<ffffffffc018a84a>] intel_crtc_set_config+0x49a/0x620 [i915]
[ 169.128385] [<ffffffff817fdd39>] ? mutex_unlock+0x9/0x10
[ 169.128391] [<ffffffff81467b69>] drm_mode_set_config_internal+0x69/0x120
[ 169.128398] [<ffffffff8119b547>] ? might_fault+0x57/0xb0
[ 169.128403] [<ffffffff8146bf93>] drm_mode_setcrtc+0x253/0x620
[ 169.128409] [<ffffffff8145c600>] drm_ioctl+0x1a0/0x6a0
[ 169.128415] [<ffffffff810b3b41>] ? get_parent_ip+0x11/0x50
[ 169.128424] [<ffffffff811e9ab8>] do_vfs_ioctl+0x2f8/0x530
[ 169.128429] [<ffffffff810d0fcd>] ? trace_hardirqs_on+0xd/0x10
[ 169.128435] [<ffffffff812e7676>] ? selinux_file_ioctl+0x56/0x100
[ 169.128439] [<ffffffff811e9d71>] SyS_ioctl+0x81/0xa0
[ 169.128445] [<ffffffff81800697>] system_call_fastpath+0x12/0x6f
Solve it by using the newly introduced drm_atomic_helper_commit_planes_on_crtc.
The problem here was that the drm_atomic_helper_commit_planes() helper
we were using was basically designed to do
begin_crtc_commit(crtc #1)
begin_crtc_commit(crtc #2)
...
commit all planes
finish_crtc_commit(crtc #1)
finish_crtc_commit(crtc #2)
The problem here is that since our hardware relies on vblank evasion,
our CRTC 'begin' function waits until we're out of the danger zone in
which register writes might wind up straddling the vblank, then disables
interrupts; our 'finish' function re-enables interrupts after the
registers have been written. The expectation is that the operations between
'begin' and 'end' must be performed without sleeping (since interrupts
are disabled) and should happen as quickly as possible. By clumping all
of the 'begin' calls together, we introducing a couple problems:
* Subsequent 'begin' invocations might sleep (which is illegal)
* The first 'begin' ensured that we were far enough from the vblank that
we could write our registers safely and ensure they all fell within
the same frame. Adding extra delay waiting for subsequent CRTC's
wasn't accounted for and could put us back into the 'danger zone' for
CRTC #1.
This commit solves the problem by using a new helper that allows an
order of operations like:
for each crtc {
begin_crtc_commit(crtc) // sleep (maybe), then disable interrupts
commit planes for this specific CRTC
end_crtc_commit(crtc) // reenable interrupts
}
so that sleeps will only be performed while interrupts are enabled and
we can be sure that registers for a CRTC will be written immediately
once we know we're in the safe zone.
The crtc->config->base.crtc update may seem unrelated, but the helper
will use it to obtain the crtc for the state. Without the update it
will dereference NULL and crash.
Changes since v1:
- Use Matt Roper's commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90398
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This should be much cleaner, with the same effects.
(cherry picked for v4.2 from commit fb9d6cf8c2)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90398
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In
commit d328c9d78d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 10 16:22:37 2015 +0200
drm/i915: Select starting pipe bpp irrespective or the primary plane
we started to select the pipe bpp from sink capabilities and not from
the primary framebuffer - that one might change (and we don't want to
incur a modeset) and sprites might contain higher bpp content too.
We also selected dithering on a 8 bpc screen displaying a 24bpp rgb
primary, because pipe_bpp is 24 for such a typical 8 bpc sink, but since
the commit mentioned above, base_bpp is always the absolute maximum
supported by the hardware, e.g., 36 bpp on my Ironlake chip. Iow. the
only way to not get dithering would have been to connect a deep color 12
bpc display, so pipe_bpp == 36 == base_bpp.
Hence only enable dithering on 6bpc screens where we difinitely and
always want it.
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Reported-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On Sun, Jul 12, 2015 at 09:52:51AM -0700, Linus Torvalds wrote:
> On Sun, Jul 12, 2015 at 1:03 AM, Jörg Otte <jrg.otte@gmail.com> wrote:
> > BUG: unable to handle kernel NULL pointer dereference at 0000000000000009
> > IP: [<ffffffffbd3447bb>] 0xffffffffbd3447bb
>
> Ugh. Please enable KALLSYMS to get sane symbols.
>
> But yes, "crtc_state->base.active" is at offset 9 from "crtc_state",
> so it's pretty clearly just that change frm
>
> - if (intel_crtc->active) {
> + if (crtc_state->base.active) {
>
> and "crtc_state" is NULL.
>
> And the code very much knows that crtc_state can be NULL, since it's
> initialized with
>
> crtc_state = state->base.state ?
> intel_atomic_get_crtc_state(state->base.state,
> intel_crtc) : NULL;
>
> Tssk. Daniel? Should I just revert that commit dec4f799d0
> ("drm/i915: Use crtc_state->active in primary check_plane func") for
> now, or is there a better fix? Like just checking crtc_state for NULL?
Indeed embarrassing. I've missed that we still have 1 caller left that's
using the transitional helpers, and those don't fill out
plane_state->state backpointers to the global atomic update since there is
no global atomic update for transitional helpers. Below diff should fix
this - we need to preferentially check crts_state->active and if that's
not set intel_crtc->active should yield the right result for the one
remaining caller (it's in the crtc_disable paths).
This fixes a regression introduced in
commit dec4f799d0
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jul 7 11:15:47 2015 +0200
drm/i915: Use crtc_state->active in primary check_plane func
which was quickly reverted in
commit 01e2d0627a
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Jul 12 15:00:20 2015 -0700
Revert "drm/i915: Use crtc_state->active in primary check_plane func"
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jörg Otte <jrg.otte@gmail.com>
Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This reverts commit dec4f799d0.
Jörg Otte reports a NULL pointder dereference due to this commit, as
'crtc_state' very much can be NULL:
crtc_state = state->base.state ?
intel_atomic_get_crtc_state(state->base.state, intel_crtc) : NULL;
So the change to test 'crtc_state->base.active' cannot possibly be
correct as-is.
There may be some other minimal fix (like just checking crtc_state for
NULL), but I'm just reverting it now for the rc2 release, and people
like Daniel Vetter who actually know this code will figure out what the
right solution is in the longer term.
Reported-and-bisected-by: Jörg Otte <jrg.otte@gmail.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since
commit 8c7b5ccb72
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:19 2015 +0300
drm/i915: Use atomic helpers for computing changed flags
we compute the plane state for a modeset before actually committing
any changes, which means crtc->active won't be correct yet. Looking at
future work in the modeset conversion targetting 4.3 the only places
where crtc_state->active isn't accurate is when disabling other CRTCs
than the one the modeset is for (when stealing connectors). Which
isn't the case here. And that's also confirmed by an audit, we do
unconditionally update crtc_state->active for the current pipe.
We also don't need to update any other plane check functions since we
only ever add the primary state to the modeset update right now.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was lost in
commit ce22dba92d
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:56 2015 +0300
drm/i915: Move toggling planes out of crtc enable/disable.
and we still need that crtc->active check since the overall modeset
flow doesn't yet take dpms state into account properly. Fixes WARNING
backtraces on at least bdw/hsw due to the ips disabling code being
upset about being run on a switched-off pipe.
We don't need a corresponding change on the enable side since with the
old setCrtc semantics we always force-enable the pipe after a modeset.
And the dpms function intel_crtc_control already checks for ->active.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville noticed that the PLL HW readout code parsed the fractional
divider value as if the fractional divider was always enabled. This may
result in a port clock state check mismatch if the preceeding modeset
disabled the fractional divider, but left a non-zero divider value in
the register.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We cannot let IPS enabled with no plane on the pipe:
BSpec: "IPS cannot be enabled until after at least one plane has
been enabled for at least one vertical blank." and "IPS must be
disabled while there is still at least one plane enabled on the
same pipe as IPS." This restriction apply to HSW and BDW.
However a shortcut path on update primary plane function
to make primary plane invisible by setting DSPCTRL to 0
was leting IPS enabled while there was no
other plane enabled on the pipe causing flickerings that we were
believing that it was caused by that other restriction where
ips cannot be used when pixel rate is greater than 95% of cdclok.
v2: Don't mess with Atomic path as pointed out by Ville.
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85583
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Silence the following -Wmaybe-uninitialized warnings and make the code
more clear.
drivers/gpu/drm/i915/intel_display.c: In function ‘__intel_set_mode’:
drivers/gpu/drm/i915/intel_display.c:11844:14: warning: ‘crtc_state’ may be used uninitialized in this function [-Wmaybe-uninitialized]
return state->mode_changed || state->active_changed;
^
drivers/gpu/drm/i915/intel_display.c:11854:25: note: ‘crtc_state’ was declared here
struct drm_crtc_state *crtc_state;
^
drivers/gpu/drm/i915/intel_display.c:11868:6: warning: ‘crtc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (crtc != intel_encoder->base.crtc)
^
drivers/gpu/drm/i915/intel_display.c:11853:19: note: ‘crtc’ was declared here
struct drm_crtc *crtc;
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The code in intel_crtc_restore_mode() sets the enabled value of all the
CRTCs when restoring the mode after a suspend/resume cycle. When more
than one CRTC is enabled, that causes drm_atomic_helper_check_modeset()
to fail if there is more than one pipe enabled, since all but one CRTC
has valid connector data. Instead, set only the enabled value for the
CRTC passed as an argument.
v2: Don't leak atomic state. (Matt)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90468
References: https://bugs.freedesktop.org/show_bug.cgi?id=90396
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
The force restore path relies on the staged config to preserve the
configuration used before a suspend/resume cycle. The update done to it
in intel_modeset_fixup_state() would cause that information to be lost
after the first modeset, making it impossible to restore the modes for
pipes B and C.
References: https://bugs.freedesktop.org/show_bug.cgi?id=90468
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Since the force restore logic will restore the CRTCs state one at a
time, it is possible that the state will be inconsistent until the whole
operation finishes. A call to intel_modeset_check_state() is done once
it's over, so don't check the state multiple times in between. This
regression was introduced in:
commit 7f27126ea3
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Nov 5 14:26:06 2014 -0800
drm/i915: factor out compute_config from __intel_set_mode v3
v2: Rename check parameter to force_restore. (Matt)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94431
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Without this frontbuffer flip when enabling planes PSR got compromised
and wasn't being enabled waiting forever on the flush that never
arrived.
Another solution would to create a enable_cursor function and split this
frontbuffer flip among the different plane enable and disable functions.
But if necessary this can be done in a follow up work. For now let's
just fix the regression.
It was removed by:
commit 87d4300a7d
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:54 2015 +0300
drm/i915: Move intel_(pre_disable/post_enable)_primary to intel_display.c, and use it there.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
chv_enable_pll() doesn't need to hold sb_lock for the entire duration of
the function. Drop the lock as soon as possible.
valleyview_set_cdclk() does a potential lock+unlock+lock+unlock cycle
with sb_lock. Grab the lock a few lines earlier so we can make do
with a single lock+unlock cycle always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename dpio_lock to sb_lock to inform the reader that its primary
purpose is to protect the sideband mailbox rather than some DPIO
state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The primary plane frobbing was removed from the sprite code in
commit ecce87ea3a
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:50 2015 +0300
drm/i915: Remove implicitly disabling primary plane for now
but the intel_flush_primary_plane() calls were left behind. Replace them
with straight forward POSTING_READ() of the sprite surface address
register.
The other user of intel_flush_primary_plane() is g4x_disable_trickle_feed()
where we can just inline the steps directly.
This allows intel_flush_primary_plane() to be killed off.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is a mplayer video failure reported with xv.
This is because there is a request to do both plane scaling
and colorkey. Because skl hw doesn't support plane scaling
and colorkey at the same time, request is failed which is expected
behavior.
To make xv operate, this patch allows colorkey continue to work
without using scaler. Then behavior would be similar to platforms
without plane scaler support.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90449
[danvet: change can_scale to bool as requested by Ville.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec says we should disable the FDI RX/TX before disabling the PCH
ports. Do so.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we're always enabling enhanced framing on CPT even if the sink
doesn't support it. Fix this up by actaully looking at what the sink
tells us.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init the display hardware when going out of suspend. This
includes:
- Hooking the PCH to the reset logic
- Restoring CDCDLK
- Enabling the DDB power
Among those, only the CDCDLK one is a bit tricky. There's some
complexity in that:
- DPLL0 (which is the source for CDCLK) has two VCOs, each with a set
of supported frequencies. As eDP also uses DPLL0 for its link rate,
once DPLL0 is on, we restrict the possible eDP link rates the chosen
VCO.
- CDCLK also limits the bandwidth available to push pixels.
So, as a first step, this commit restore what the BIOS set, until I can
do more testing.
In case that's of interest for the reviewer, I've unit tested the
function that derives the decimal frequency field:
#include <stdio.h>
#include <stdint.h>
#include <assert.h>
#define ARRAY_SIZE(x) (sizeof(x) / sizeof(*(x)))
static const struct dpll_freq {
unsigned int freq;
unsigned int decimal;
} freqs[] = {
{ .freq = 308570, .decimal = 0b01001100111},
{ .freq = 337500, .decimal = 0b01010100001},
{ .freq = 432000, .decimal = 0b01101011110},
{ .freq = 450000, .decimal = 0b01110000010},
{ .freq = 540000, .decimal = 0b10000110110},
{ .freq = 617140, .decimal = 0b10011010000},
{ .freq = 675000, .decimal = 0b10101000100},
};
static void intbits(unsigned int v)
{
int i;
for(i = 10; i >= 0; i--)
putchar('0' + ((v >> i) & 1));
}
static unsigned int freq_decimal(unsigned int freq /* in kHz */)
{
return (freq - 1000) / 500;
}
static void test_freq(const struct dpll_freq *entry)
{
unsigned int decimal = freq_decimal(entry->freq);
printf("freq: %d, expected: ", entry->freq);
intbits(entry->decimal);
printf(", got: ");
intbits(decimal);
putchar('\n');
assert(decimal == entry->decimal);
}
int main(int argc, char **argv)
{
int i;
for (i = 0; i < ARRAY_SIZE(freqs); i++)
test_freq(&freqs[i]);
return 0;
}
v2:
- Rebase on top of -nightly
- Use (freq - 1000) / 500 for the decimal frequency (Ville)
- Fix setting the enable bit of HSW_NDE_RSTWRN_OPT (Ville)
- Rename skl_display_{resume,suspend} to skl_{init,uninit}_cdclk to
be consistent with the BXT code (Ville)
- Store boot CDCLK in ddi_pll_init (Ville)
- Merge dev_priv's skl_boot_cdclk into cdclk_freq
- Use LCPLL_PLL_LOCK instead of (1 << 30) (Ville)
- Replace various '0' by SKL_DPLL0 to be a bit more explicit that
we're programming DPLL0
- Busy poll the PCU before doing the frequency change. It takes about
3/4 cycles, each separated by 10us, to get the ACK from the CPU
(Ville)
v3:
- Restore dev_priv->skl_boot_cdclk, leaving unification with
dev_priv->cdclk_freq for a later patch (Daniel, Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we will often pageflip to an active surface, we will often have to
wait for the surface to be written before issuing the flip. Also we are
likely to wait on that surface in plenty of time before the vblank.
Since we have a mechanism for boosting when a flip misses the expected
vblank, curtain the number of times we RPS boost when simply waiting for
mmioflip.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, we only track the last request globally across all engines.
This prevents us from issuing concurrent read requests on e.g. the RCS
and BCS engines (or more likely the render and media engines). Without
semaphores, we incur costly stalls as we synchronise between rings -
greatly impacting the current performance of Broadwell versus Haswell in
certain workloads (like video decode). With the introduction of
reference counted requests, it is much easier to track the last request
per ring, as well as the last global write request so that we can
optimise inter-engine read read requests (as well as better optimise
certain CPU waits).
v2: Fix inverted readonly condition for nonblocking waits.
v3: Handle non-continguous engine array after waits
v4: Rebase, tidy, rewrite ring list debugging
v5: Use obj->active as a bitfield, it looks cool
v6: Micro-optimise, mostly involving moving code around
v7: Fix retire-requests-upto for execlists (and multiple rq->ringbuf)
v8: Rebase
v9: Refactor i915_gem_object_sync() to allow the compiler to better
optimise it.
Benchmark: igt/gem_read_read_speed
hsw:gt3e (with semaphores):
Before: Time to read-read 1024k: 275.794µs
After: Time to read-read 1024k: 123.260µs
hsw:gt3e (w/o semaphores):
Before: Time to read-read 1024k: 230.433µs
After: Time to read-read 1024k: 124.593µs
bdw-u (w/o semaphores): Before After
Time to read-read 1x1: 26.274µs 10.350µs
Time to read-read 128x128: 40.097µs 21.366µs
Time to read-read 256x256: 77.087µs 42.608µs
Time to read-read 512x512: 281.999µs 181.155µs
Time to read-read 1024x1024: 1196.141µs 1118.223µs
Time to read-read 2048x2048: 5639.072µs 5225.837µs
Time to read-read 4096x4096: 22401.662µs 21137.067µs
Time to read-read 8192x8192: 89617.735µs 85637.681µs
Testcase: igt/gem_concurrent_blit (read-read and friends)
Cc: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> [v8]
[danvet: s/\<rq\>/req/g]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The merged seqno->request conversion from John called request
variables req, but some (not all) of Chris' recent patches changed
those to just rq. We've had a lenghty (and inconclusive) discussion on
irc which is the more meaningful name with maybe at most a slight bias
towards req.
Given that the "don't change names without good reason to avoid
conflicts" rule applies, so lets go back to a req everywhere for
consistency. I'll sed any patches for which this will cause conflicts
before applying.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
[danvet: s/origina/merged/ as pointed out by Chris - the first
mass-conversion patch was from Chris, the merged one from John.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Since DRM_ROTATE is counter clockwise (which is compliant with Xrandr),
and HW rotation is clockwise, swapping 90/270 to work as expected from
userspace.
v2: Rebased
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Explain why a few fields of the new pipe_config have their values
preserved, while the others are zeroed.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ARGB8888 is used for cursors on all platforms so we need to allow it
everywhere.
ABGR8888 is currently only honoured:
- on VLV/CHV in sprite planes
- on SKL+ for primary and sprite planes
so only allow it for those platforms.
Note that we only support ARGB8888/ABGR8888 on the primary plane for
SKL/BXT because we have in line of sight the pipe bottom color on those
platforms and because the primary plane programming on VLV/CHV doesn't
anything different for those formats today.
v2: Fix the logic to forbid the creation ABGR2101010 fbs (Ville)
v3: Still allow the creation of ARGB8888 fbs now that cursor planes use
real fb objects (found by PRTS).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We just have have VLV and CHV sprites programming the hardware
differently for the ABGR2101010 so keep them working.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That define makes it hard to figure out what is the actual list of
formats at a glance. Expand it then.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the modeset code is reached with a CRTC that only needs a flip, the
code that assigns PLLs is skipped. But since there is still a state swap
for that CRTC, the current PLL assignment needs to be preserved. I
missed the ddi_pll_sel field in the following commit, which causes
warnings in DDI platforms.
commit 4978cc93d9
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:21 2015 +0300
drm/i915: Preserve shared DPLL information in new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90410
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the following commit, the place where the contents of dpll_hw_state
in crtc_state where zeroed was changed. Prior to that commit, it
happened when the new state was allocated, but now that happens just
before the call the .crtc_compute_clock() hook. The DP code for SKL,
however, sets up the (private) PLL in the encoder compute config
function that has already run by the time that memset() is reached,
causing the previous value to be lost.
This patch fixes the issue by moving the memset() down the call chain,
so that it is only called if the values in dpll_hw_state are going to be
updated.
commit 4978cc93d9
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:21 2015 +0300
drm/i915: Preserve shared DPLL information in new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90462
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reported-and-tested-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just so it is grouped logically in line with other data and makes a
rather verbose output a bit shorter.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville noticed in another patch we we didn't need them at all, so remove
them. It's worth saying that it makes no difference to code generated as
gcc is clever enough to optimize it out.
v2: Remove 'break' after 'return' in switches (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now prefix our functions/enums/data with the first platform it has
been introduced. Do that for the primary plane formats.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: s/gen2/i8xx/ and s/gen4/i965/ ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We advertize C8 in the primary plane formats didn't have the
corresponding code to set PLANE_CTL accordingly.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's be consistent with the others skl_plane_ctl_*() functions and use
a MISSING_CASE(). Not only that, but it's a rude to BUG() the whole
machine here.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No reason to not follow the 80 chars rule, renaming the local variable
makes it easy.
Cc: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We usually use a new line before those kind of return statements. Also
the various skl_plane_ctl*() functions weren't consistent.
Cc: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During check_crtc_state, scaler_id mispatch is being reported for HSW.
This is applicable for skl+ and not for HSW. It is introduced by
commit id:
commit a1b2278e4d
Author: Chandra Konduru <chandra.konduru@intel.com>
Date: Tue Apr 7 15:28:45 2015 -0700
drm/i915: skylake panel fitting using shared scalers
This patch will make sure that we leave scaler_id as 0 for platforms
before skl and set for skl+ only. This way scaler_id check during
check_crtc_state will pass for both prior to skl and skl+ platforms.
v2:
-Leave scaler_id as 0 for gen < 9 (Daniel)
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
References: http://lists.freedesktop.org/archives/intel-gfx/2015-May/065741.html
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we perform the mmio-flip without any locking and then try to acquire
the struct_mutex prior to dereferencing the request, it is possible for
userspace to queue a new pageflip before the worker can finish clearing
the old state - and then it will clear the new flip request. The result
is that the new flip could be completed before the GPU has finished
rendering.
The bugs stems from removing the seqno checking in
commit 536f5b5e86
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Thu Nov 6 11:03:40 2014 +0200
drm/i915: Make mmio flip wait for seqno in the work function
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Synchronising to an object active on the same ring is a no-op, for the
benefit of execbuffer scheduler. However, for CS flips this means that
we can forgo checking whether the last write request of the object is
actually queued and more importantly whether the cache flush for the
write was emitted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We no longer interpolate domains in the same manner, and even if we did,
we should trust setting either of the other write domains would trigger
an invalidation rather than force it. Remove the tweaking of the
read_domains since it serves no purpose and use
i915_gem_object_wait_rendering() directly.
Note that this goes back to
commit a8198eea15
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Apr 13 22:04:09 2011 +0100
drm/i915: Introduce i915_gem_object_finish_gpu()
and gpu domain tracking died in
commit cc889e0f6c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jun 13 20:45:19 2012 +0200
drm/i915: disable flushing_list/gpu_write_list
which is more than 1 year older.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add notes with information dug out of git history.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In skylake update plane functions, intel_tile_height() is called with
bits_per_pixel instead of pixel_format. Correcting it.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
[danvet: Fixup alignment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the recent modeset internal rework, we wind up setting crtc_state->enable
to false, but leave crtc_state->active as true following a
drmModeSetCrtc(fb=0), which is incorrect. This mismatch gets caught by
drm_atomic_crtc_check() and causes subsequent atomic operations (such as plane
updates while the CRTC is disabled) to fail.
Bisect points to
commit dad9a7d6d96630182fb52aae7c3856e9e7285e13
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:19 2015 +0300
drm/i915: Use atomic helpers for computing changed flags
as the commit that actually triggers the regression.
The difference compared to (which this patch reverts)
commit 90d469067d
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Thu May 7 14:31:28 2015 -0700
drm/i915: Set crtc_state->active to false when CRTC is disabled (v2)
is that we know keep state->active/enable in sync for all legacy
modeset paths, as it should be.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reported-and-Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Directly squash in the revert and augment the commit
message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Revert "drm/i915: Set crtc_state->active to false when CRTC is disabled (v2)"
This reverts commit 90d469067d.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVWh3TAAoJEHm+PkMAQRiG/kwH/2c9irodp2+M9OUnX2bfsBb6
LnChiDpvkF5BB8jhP6d/XmvPp4NJzAbTxByhjdfb2E2HkorCUHCOIn2tI1TE2pUs
2qjkOVH+XCzoV0goGtQjzK1ht8f2IrtlDiEjyRekK5cJHzhggb22QPtWL4npyd0O
reDmG2jsRaF9POr9uLSFEv4CEnkksmRLUU0vuQX0TZeCJ41O7TXrkN/wKrLZ5mj4
IWpqXQaSlrffq/T5HnVbXBxk3/T8QmhrIoppiMpV1mUVj0uTqlFRNi5qwT2Nit1h
FVljWI4+WgOk3bf7fUlp+ahopjkTgu+GuXkiRP/pdgWNQO0cxCWSAzSndAlIIAE=
=uOoJ
-----END PGP SIGNATURE-----
Backmerge v4.1-rc4 into into drm-next
We picked up a silent conflict in amdkfd with drm-fixes and drm-next,
backmerge v4.1-rc5 and fix the conflicts
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/drm_irq.c
Currently vlv_wait_port_ready() waits for all four lanes on the
appropriate channel. This no longer works on CHV when the unused
lanes may be power gated. So pass in a mask of lanes that the
caller is expecting to be ready.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maarten Lankhorst