Add the capability to split the Tx queues onto their own
interrupts with their own napi contexts. This gives the
opportunity for more direct control of Tx interrupt
handling, such as CPU affinity and interrupt coalescing,
useful for some traffic loads.
v2: use ethtool -L, not a vendor specific priv-flag
v3: simplify logging, drop unnecessary "no-change" tests
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
We give the tx clean path its own budget and service routine in
order to give a little more leeway to be more aggressive, and
in preparation for coming changes. We've found this gives us
a little better performance in some packet processing scenarios
without hurting other scenarios.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
We really don't need to hit the Rx queue doorbell so many times,
we can wait to the end and cause a little less thrash.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release skb memory in mvpp2_rx() if mvpp2_rx_refill routine fails
Fixes: b501585467 ("net: mvpp2: fix refilling BM pools in RX path")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO device reset assert and deassert length was created by
usleep_range() but that does not ensure optimal handling of
all the different values from device tree properties.
By switching to the new flexible sleeping helper function,
fsleep(), the correct delay function is called depending on
delay length, e.g. udelay(), usleep_range() or msleep().
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load new "reset-post-delay-us" value from MDIO properties,
and if configured to a greater then zero delay do a
flexible sleeping delay after MDIO bus reset deassert.
This allows devices to exit reset state before start
bus communication.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO bus reset pulse width is created by using udelay()
and that function might not be optimal depending on
device tree value. By switching to the new fsleep() helper
the correct delay function is called depending on
delay length, e.g. udelay(), usleep_range() or msleep().
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate nic_info dynamically - n_entries is not constant.
Attach the tunnel offload info only to the uplink representor.
We expect the "main" netdev to be unregistered in switchdev
mode, and there to be only one uplink representor.
Drop the udp_tunnel_drop_rx_info() call, it was not there until
commit b3c2ed21c0 ("net/mlx5e: Fix VXLAN configuration restore after function reload")
so the device doesn't need it, and core should handle reloads and
reset just fine.
v2:
- don't drop the ndos on reprs, and register info on uplink repr.
v4:
- Move netdev tunnel structure handling to en_main.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The DR TX state machine supports the following order:
modify header, push vlan and encapsulation.
Instead fs_dr would pass:
push vlan, modify header and encapsulation.
The above caused the rule creation to fail on invalid action
sequence provided error.
Fixes: 6a48faeeca ("net/mlx5: Add direct rule fs_cmd implementation")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently PF and VF representor netdevice carrier is always controlled
by controlling the representor netdevice device state as up/down.
Representor netdevice state change undergoes one or more txq/rxq
destroy/create commands to firmware, skb and its rx buffer allocation,
health reporters creation and more.
Due to this limitation users do not have the ability to just change
the carrier of the non uplink representors without modifying the
device state.
In one use case when the eswitch physical port carrier is down/up,
user needs to update the VF link state to same as physical port
carrier.
Example of updating VF representor carrier state:
$ ip link set enp0s8f0npf0vf0 carrier off
$ ip link set enp0s8f0npf0vf0 carrier on
This enhancement results into VF link state change which is
represented by the VF representor netdevice carrier.
This enables users to modify the representor carrier without modifying
the representor netdevice state.
A simple test is run using [1] to calculate the time difference between
updating carrier vs updating device state (to update just the carrier)
with one VF to simulate 255 VFs.
Time taken to update the carrier using device up/down:
$ time ./calculate.sh dev enp0s8f0npf0vf0
real 0m30.913s
user 0m0.200s
sys 0m11.168s
Time taken to update just the carrier using carrier iproute2 command:
$ time ./calculate.sh carrier enp0s8f0npf0vf0
real 0m2.142s
user 0m0.160s
sys 0m2.021s
Test shows that its better to use carrier on/off user interface to notify
link up/down event to VF compare to device up/down interface, because
carrier user interface delivers the same event 15 times faster.
[1] https://github.com/paravmellanox/myscripts/blob/master/calculate_carrier_time.sh
Signed-off-by: Parav Pandit <parav@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Set the timeout value as per cfg80211's set_power_mgmt() request. If the
requested value value is left undefined we set it to 2 seconds, the
maximum supported value.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721112302.22718-1-nsaenzjulienne@suse.de
wl1251_event_ps_report() should not always return 0 because
wl1251_ps_set_mode() may fail. Change it to return 'ret'.
Fixes: f7ad1eed4d ("wl1251: retry power save entry")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200730073939.33704-1-wanghai38@huawei.com
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200728114128.1218310-1-vaibhavgupta40@gmail.com
In some Intersil files, the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723135254.594984-1-f.suligoi@asem.it
Add the missing platform_device_unregister() before return from
qtnf_core_mac_alloc() in the error handling case.
Fixes: 616f5701f4 ("qtnfmac: assign each wiphy to its own virtual platform device")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200730064910.37589-1-wanghai38@huawei.com
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.
When memory is allocated in 'ipw2100_msg_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_msg_allocate
Moreover, 'ipw2100_msg_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'status_queue_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_rx_allocate
--> status_queue_allocate
Moreover, 'ipw2100_rx_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'bd_queue_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_rx_allocate
--> bd_queue_allocate
Moreover, 'ipw2100_rx_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'ipw2100_tx_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_tx_allocate
Moreover, 'ipw2100_tx_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'ipw_queue_tx_init()' (ipw2200.c),
GFP_KERNEL can be used because it is called from a call chain that already
uses GFP_KERNEL and no spin_lock is taken in the between.
The call chain is:
ipw_up
--> ipw_load
--> ipw_queue_reset
--> ipw_queue_tx_init
'ipw_up()' already uses GFP_KERNEL for some other memory allocations.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200722101716.26185-1-christophe.jaillet@wanadoo.fr
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_tx_allocate
No lock is taken in the between.
So it is safe to use GFP_KERNEL in 'ipw2100_tx_allocate()'.
BTW, 'ipw2100_queues_allocate()' also calls 'ipw2100_msg_allocate()' which
already allocates some memory using GFP_KERNEL.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200722101701.26126-1-christophe.jaillet@wanadoo.fr
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions as through
the generic framework, PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721150547.371763-1-vaibhavgupta40@gmail.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719111124.58167-1-grandmaster@al2klimov.de
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719110115.58085-1-grandmaster@al2klimov.de
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200718100240.98593-1-grandmaster@al2klimov.de
Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.
With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.
The callbacks make use of PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device() and
pci_set_power_state() to do required operations. In generic mode, they are
no longer needed.
Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.
The .suspend() callback is invoking rt2x00lib_suspend() which needs to be
modified as generic rt2x00pci_suspend() has no pm_message_t type argument,
passed to it, which is required by it according to its declaration.
Although this variable remained unused in the function body. Hence, remove
it from the function definition & declaration.
rt2x00lib_suspend() is also invoked by rt2x00usb_suspend() and
rt2x00soc_suspend(). Thus, modify the functional call accordingly in their
function body.
Earlier, .suspend() & .resume() were exported and were used by the
following drivers:
- drivers/net/wireless/ralink/rt2x00/rt2400pci.c
- drivers/net/wireless/ralink/rt2x00/rt2500pci.c
- drivers/net/wireless/ralink/rt2x00/rt2800pci.c
- drivers/net/wireless/ralink/rt2x00/rt61pci.c
Now, we only need to bind "struct dev_pm_ops" variable to
"struct pci_driver". Thus, make the callbacks static. Declare an
"extern const struct dev_pm_ops" variable and bind PM callbacks to it. Now,
export the variable instead and use it in respective drivers.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717110928.454867-1-vaibhavgupta40@gmail.com
Moved macros used for Vendor/Device ID from wilc1000 driver to common
header file and changed macro name for consistency with other macros.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717051134.19160-1-ajay.kathat@microchip.com
In the implementation of mt7601u_mcu_msg_send(), skb is supposed to be
consumed on all execution paths. Release skb before returning if
test_bit() fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200718052630.11032-1-navid.emamdoost@gmail.com
Missing this firmware is not fatal, my wifi card still works. Even more,
I couldn't find any documentation what it is or where to get it. So, I
don't think the users should be notified if it is missing. If you browse
the net, you see the message is present is in quite some logs. Better
remove it.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200625165210.14904-1-wsa@kernel.org
Without this patch, RTL8821CE will not have coex support,
and will crash the system because of the NULL pointers
for the coex functions.
While RTL8822C series are WiFi + BT combo chips, it needs
the co-existence mechanism for the device to work on both
WiFi and BT without interfering each other. And the coex
support has already been added before, most of the mechanisms
are implemented. The driver should just add corresponding
functions to operate on different types of chips and its
coex parameters.
Fixes: f745eb9ca5 ("rtw88: 8821c: Add 8821CE to Kconfig and Makefile")
Signed-off-by: Ping-Cheng Chen <pc.chen@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200724054208.31115-1-yhchuang@realtek.com
The sparse tool complains as follows:
drivers/net/wireless/realtek/rtw88/rtw8821c.c:1374:32: warning:
symbol 'rtw8821c_rtw_pwr_track_tbl' was not declared. Should it be static?
This variable is not used outside of rtw8821c.c, so this commit
marks it static.
Fixes: 3a4312828c ("rtw88: 8821c: add power tracking")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721134901.33968-1-weiyongjun1@huawei.com
It's very useful to send H2C command for debug usage. Add an entry
for sending H2C command to firmware.
usage example:
echo 42,00,00,43,02,00,00,00 > /sys/kernel/debug/ieee80211/phyX/rtw88
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-8-yhchuang@realtek.com
Sometimes mac80211 will just ask driver to change the interface
instead of to remove and then add a new one. And for driver, to
change the interface is just simply to remove and add a new one
but change the type of it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-6-yhchuang@realtek.com
The coex mechanism used to skip upon the freeze flag is raised.
That will cause the coex mechanism being skipped unexpectedly.
Coex only wanted to keep the TDMA table from being changed by
BT side.
So, check the freeze and reason, if the coex reason is coming
from BT info, skip it, to make sure the coex triggered by Wifi
itself can work.
This is required for the AP mode, while the control flow is
different with STA mode. When starting an AP mode, the AP mode
needs to start working immedaitely after leaving IPS, and the
freeze flag could be raised. If the coex info is skipped, then
the AP mode will not set the antenna owner, leads to TX stuck.
Fixes: 4136214f7c ("rtw88: add BT co-existence support")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-5-yhchuang@realtek.com
Previous settings for TX descriptors of and reserved page packets
are insufficient.
For the sequence number of packets downloaded to reserved page, it
should be filled by hardware.
And for ps-poll packets in reserved page, to prevent AID being
changed by hardware, NAVUSEHDR should be set.
Additionally, the rate should be adjusted based on the current band
for mgmt and reserved page packets.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-4-yhchuang@realtek.com
Fix the transmission is not sent with short GI under
some conditions even if the receiver supports short GI.
If VHT capability IE exists in the beacon, the original
code uses the short GI for 80M field as driver's short GI
setting for transmission, even the current bandwidth is
not 80MHz.
Short GI supported fields for 20M/40M are informed in HT
capability information element, and short GI supported
field for 80M is informed in VHT capability information
element.
These three fields may be set to different values.
Driver needs to record each short GI support field for
each bandwidth, and send correct info depends on current
bandwidth to the WiFi firmware.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-3-yhchuang@realtek.com
Convert the type of LDPC field to boolen because
LDPC field of RA info H2C command to firmware
is only one bit.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-2-yhchuang@realtek.com
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions as through
the generic framework, PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721125514.145607-1-vaibhavgupta40@gmail.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719121224.58581-1-grandmaster@al2klimov.de
The variables ant_num and single_ant_path are being initialized with a
value that is never read and are being updated later with a new value.
The initializations are redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723163214.995226-1-colin.king@canonical.com
* locking fixes
* tx queue mapping fixes for 7615/7915
* ARP filter offload for 7663
* runtime power management for 7663
* testmode support for mfg calibration
* memory leak fixes
* support for more channels
-----BEGIN PGP SIGNATURE-----
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAl8XH2gACgkQ130UHQKnbvVrIwCfcjYdZ0A9ArrrAR6nvmwvh2K2
qqwAniwJcp/2wYNHisIIduM3V5UKtnsU
=Lpxf
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2020-07-21' of https://github.com/nbd168/wireless
mt76 patches for 5.9
* locking fixes
* tx queue mapping fixes for 7615/7915
* ARP filter offload for 7663
* runtime power management for 7663
* testmode support for mfg calibration
* memory leak fixes
* support for more channels
# gpg: Signature made Tue 21 Jul 2020 08:01:28 PM EEST using DSA key ID 02A76EF5
# gpg: Good signature from "Felix Fietkau <nbd@nbd.name>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 75D1 1A7D 91A7 710F 4900 42EF D77D 141D 02A7 6EF5
This is a collection of minor fixes including typos, white space, and
style. No functional changes.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
The profile ID map lock should be held till the caller completes
all references of that profile entries.
The current code releases the lock right after the match search.
This caused a driver issue when the profile map entries were
referenced after it was freed in other thread after the lock was
released earlier.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update the PTYPE lookup table to reflect values that can be set by the
hardware.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Disable VLAN pruning when entering promiscuous mode, and re-enable it
when exiting.
Without this VLAN-over-bridge topologies created on the device won't be
functional unless rx-vlan-filter is explicitly disabled with ethtool.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the ice_init_hw_tbls, if the devm_kcalloc for es->written fails, catch
that error and bail out gracefully, instead of continuing with a NULL
pointer.
Fixes: 32d63fa1e9 ("ice: Initialize DDP package structures")
Signed-off-by: Surabhi Boob <surabhi.boob@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This is a port of commit 248de22e63 ("i40e/i40evf: Account for frags
split over multiple descriptors in check linearize")
As part of testing workloads (read/write) using larger IO size (128K)
tx_timeout is observed and whenever it happens, it was due to
tx_linearize.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently VFs are only allowed to get 16, 4, and 1 queue pair by
default, which require 17, 5, and 2 MSI-X vectors respectively. This
is because each VF needs a MSI-X per data queue and a MSI-X for its
other interrupt. The calculation is based on the number of VFs created,
MSI-X available, and queue pairs available at the time of VF creation.
Unfortunately the values above exclude 2 queue pairs when only 3 MSI-X
are available to each VF based on resource constraints. The current
calculation would default to 2 MSI-X and 1 queue pair. This is a waste
of resources, so fix this by allowing 2 queue pairs per VF when there
are between 2 and 5 MSI-X available per VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This fix has been added to address memory leak issues resulting from
triggering a sudden driver reset which does not allow us to follow our
normal removal flows for SW XLT entries for advanced features.
- Adding call to destroy flow profile locks when clearing SW XLT tables.
- Extraction sequence entries were not correctly cleared previously
which could cause ownership conflicts for repeated reset-replay calls.
Fixes: 31ad4e4ee1 ("ice: Allocate flow profile")
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Display and count some useful hot-path statistics. The usefulness is as
follows:
- tx_restart: use to determine if the transmit ring size is too small or
if the transmit interrupt rate is too low.
- rx_gro_dropped: use to count drops from GRO layer, which previously were
completely uncounted when occurring.
- tx_busy: use to determine when the driver is miscounting number of
descriptors needed for an skb.
- tx_timeout: as our other drivers, count the number of times we've reset
due to timeout because the kernel only prints a warning once per netdev.
Several of these were already counted but not displayed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The page reuse statistic wasn't even being displayed to the user, even
though the driver counted it. Don't waste the struct space and hot-path
cycles since the driver doesn't display it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replacing flow profile locks with RSS profile locks in the function to
remove all RSS rules for a given VSI. This is to align the locks used
for RSS rule addition to VSI and removal during VSI teardown to avoid
a race condition owing to several iterations of the above operations.
In function to get RSS rules for given VSI and protocol header replacing
the pointer reference of the RSS entry with a copy of hash value to
ensure thread safety.
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
set_rss_lut can fail due to incorrect vsi_id mask. vsi_id is 10 bit
but mask was 0x1FF whereas it should be 0x3FF.
For vsi_num >= 512, FW set_rss_lut can fail with return code
EACCESS (VSI ownership issue) because software was providing
incorrect vsi_num (dropping 10th bit due to incorrect mask) for
set_rss_lut admin command
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The grst_delay variable in ice_check_reset contains the maximum time
(in 100 msec units) that the driver will wait for a reset event to
transition to the Device Active state. The value is the sum of three
separate components:
1) The maximum time it may take for the firmware to process its
outstanding command before handling the reset request.
2) The value in RSTCTL.GRSTDEL (the delay firmware inserts between first
seeing the driver reset request and the actual hardware assertion).
3) The maximum expected reset processing time in hardware.
Referring to this total time as "grst_delay" is misleading and
potentially confusing to someone checking the code and cross-referencing
the hardware specification.
Fix this by renaming the variable to "grst_timeout", which is more
descriptive of its actual use.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In certain configurations without power management support, the
following warnings happen:
drivers/net/ethernet/intel/ice/ice_main.c:4214:12: warning:
'ice_resume' defined but not used [-Wunused-function]
4214 | static int ice_resume(struct device *dev)
| ^~~~~~~~~~
drivers/net/ethernet/intel/ice/ice_main.c:4150:12: warning:
'ice_suspend' defined but not used [-Wunused-function]
4150 | static int ice_suspend(struct device *dev)
| ^~~~~~~~~~~
Mark these functions as __maybe_unused to make it clear to the
compiler that this is going to happen based on the configuration,
which is the standard for these types of functions.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
* code cleanups and fixups as usual
* AQL & internal TXQ improvements from Felix
* some mesh 802.1X support bits
* some injection improvements from Mathy of KRACK
fame, so we'll see what this results in ;-)
* some more initial S1G supports bits, this time
(some of?) the userspace APIs
-----BEGIN PGP SIGNATURE-----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=FR6T
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a number of changes
* code cleanups and fixups as usual
* AQL & internal TXQ improvements from Felix
* some mesh 802.1X support bits
* some injection improvements from Mathy of KRACK
fame, so we'll see what this results in ;-)
* some more initial S1G supports bits, this time
(some of?) the userspace APIs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We expecte prog_p to be protected by rcu, so adding the rcu annotation
to fix the following sparse warning:
drivers/net/tun.c:3003:36: warning: incorrect type in argument 2 (different address spaces)
drivers/net/tun.c:3003:36: expected struct tun_prog [noderef] __rcu **prog_p
drivers/net/tun.c:3003:36: got struct tun_prog **prog_p
drivers/net/tun.c:3292:42: warning: incorrect type in argument 2 (different address spaces)
drivers/net/tun.c:3292:42: expected struct tun_prog **prog_p
drivers/net/tun.c:3292:42: got struct tun_prog [noderef] __rcu **
drivers/net/tun.c:3296:42: warning: incorrect type in argument 2 (different address spaces)
drivers/net/tun.c:3296:42: expected struct tun_prog **prog_p
drivers/net/tun.c:3296:42: got struct tun_prog [noderef] __rcu **
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl8jebYACgkQSD+KveBX
+j6Vnwf/Z0LVx9aIVOl+lfIuIqeKCtbwdoh9kTa6wNIuX0c/NnG2u2bt9GjOGyKh
LqTVX6Nu2sfcuTtkyrqhiIj6PyivzHciDN+au8hqrvBV429KsKbNu+jvXJmL/mXX
BU47mExP6ZMsWDTkBEnRQnwSsKDHbUw+xT7LeO36DE9Rrjlox6AtjFeWuJBoyBMO
QlbTjgDHtwV1bJe8sVBrymZmQcy582hEcoZqAGnzDVAF5DW6TAZkSqx3UdiO6KeN
hLTMYZbiIDRDs3n1dOyLlQlXSWzzQzw1gae/Q7nJsYu4VPsGjEeNXUw8d9RNWv4v
EGhJF999G9Np6mjzWtXDC00tM2X7LQ==
=+emh
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-07-30' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-07-30
This small patchset introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.18:
('net/mlx5e: fix bpf_prog reference count leaks in mlx5e_alloc_rq')
For -stable v5.7:
('net/mlx5e: E-Switch, Add misc bit when misc fields changed for mirroring')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2020-07-30
This series contains updates to e100, e1000, e1000e, igb, igbvf, ixgbe,
ixgbevf, iavf, and driver documentation.
Vaibhav Gupta converts legacy .suspend() and .resume() to generic PM
callbacks for e100, igbvf, ixgbe, ixgbevf, and iavf.
Suraj Upadhyay replaces 1 byte memsets with assignments for e1000,
e1000e, igb, and ixgbe.
Alexander Klimov replaces http links with https.
Miaohe Lin replaces uses of memset to clear MAC addresses with
eth_zero_addr().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-07-30
This series contains updates to the e1000e and igb drivers.
Aaron Ma allows PHY initialization to continue if ULP disable failed for
e1000e.
Francesco Ruggeri fixes race conditions in igb reset that could cause panics.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to %pM instead of using custom code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to %pM instead of using custom code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-07-31
Here's the main bluetooth-next pull request for 5.9:
- Fix firmware filenames for Marvell chipsets
- Several suspend-related fixes
- Addedd mgmt commands for runtime configuration
- Multiple fixes for Qualcomm-based controllers
- Add new monitoring feature for mgmt
- Fix handling of legacy cipher (E4) together with security level 4
- Add support for Realtek 8822CE controller
- Fix issues with Chinese controllers using fake VID/PID values
- Multiple other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function invokes bpf_prog_inc(), which increases the reference
count of a bpf_prog object "rq->xdp_prog" if the object isn't NULL.
The refcount leak issues take place in two error handling paths. When
either mlx5_wq_ll_create() or mlx5_wq_cyc_create() fails, the function
simply returns the error code and forgets to drop the reference count
increased earlier, causing a reference count leak of "rq->xdp_prog".
Fix this issue by jumping to the error handling path err_rq_wq_destroy
while either function fails.
Fixes: 422d4c401e ("net/mlx5e: RX, Split WQ objects for different RQ types")
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The flow_source must be specified, even for rule without matching
source vport, because some actions are only allowed in uplink.
Otherwise, rule can't be offloaded and firmware syndrome happens.
Fixes: 6fb0701a9c ("net/mlx5: E-Switch, Add support for offloading rules with no in_port")
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The modified flow_context fields in FTE must be indicated in
modify_enable bitmask. Previously, the misc bit in modify_enable is
always set as source vport must be set for each rule. So, when parsing
vxlan/gre/geneve/qinq rules, this bit is not set because those are all
from the same misc fileds that source vport fields are located at, and
we don't need to set the indicator twice.
After adding per vport tables for mirroring, misc bit is not set, then
firmware syndrome happens. To fix it, set the bit wherever misc fileds
are changed. This also makes it unnecessary to check misc fields and set
the misc bit accordingly in metadata matching, so here remove it.
Besides, flow_source must be specified for uplink because firmware
will check it and some actions are only allowed for packets received
from uplink.
Fixes: 96e326878f ("net/mlx5e: Eswitch, Use per vport tables for mirroring")
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the driver restores only IPv4 tunnel headers.
Add support for restoring IPv6 tunnel header.
Fixes: b8ce903709 ("net/mlx5e: Restore tunnel metadata on miss")
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix the missing clk_disable_unprepare() before return
from gemini_ethernet_port_probe() in the error handling case.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_get_resource() may fail and return NULL, so we had better
check its return value to avoid a NULL pointer dereference a bit later
in the code. Fix it to use devm_platform_ioremap_resource_byname()
instead of calling platform_get_resource_byname() and devm_ioremap().
Fixes: 8425c41d1e ("net: ll_temac: Extend support to non-device-tree platforms")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes coccicheck warning:
./drivers/net/ethernet/broadcom/bnxt/bnxt.c:3730:19-37: WARNING:
dma_alloc_coherent use in stats -> hw_stats already zeroes out
memory, so memset is not needed
dma_alloc_coherent use in status already zeroes out memory,
so memset is not needed
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of struct octeon_dispatch is too small, it is better to use
kmalloc instead of vmalloc.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the flex_array_size() helper to calculate the size of a
flexible array member within an enclosing structure.
This helper offers defense-in-depth against potential integer
overflows, while at the same time makes it explicitly clear that
we are dealing witha flexible array member.
Also, remove unnecessary pointer identifier sub_pool.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On an error return, jump to the unlock at the end to be sure
to unlock the queue_lock mutex.
Fixes: 0925e9db4d ("ionic: use mutex to protect queue operations")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
in recent kernel versions there are warnings about incorrect MTU size
like these:
eth0: mtu greater than device maximum
mtk_soc_eth 1b100000.ethernet eth0: error -22 setting MTU to include DSA overhead
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Fixes: 72579e14a1 ("net: dsa: don't fail to probe if we couldn't set the MTU")
Fixes: 7a4c53bee3 ("net: report invalid mtu value via netlink extack")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If some processes in nixge_probe() fail, free_netdev(dev)
needs to be called to aviod a memory leak.
Fixes: 87ab207981 ("net: nixge: Separate ctrl and dma resources")
Fixes: abcd3d6fc6 ("net: nixge: Fix error path for obtaining mac address")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Lu Wei <luwei32@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_zero_addr() to clear mac address instead of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use eth_zero_addr() to clear mac address instead of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This converts all the existing DECLARE_TASKLET() (and ...DISABLED)
macros with DECLARE_TASKLET_OLD() in preparation for refactoring the
tasklet callback type. All existing DECLARE_TASKLET() users had a "0"
data argument, it has been removed here as well.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Replace memsets of 1 byte with simple assignment.
Issue found with checkpatch.pl
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace memsets of 1 byte with simple assignment.
Issue found with checkpatch.pl
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace memsets of 1 byte with simple assignments.
Issue found with checkpatch.pl
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace memsets of 1 byte with simple assignments.
Issue reported by checkpatch.pl.
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With legacy PM hooks, it was the responsibility of a driver to manage PCI
states and also the device's power state. The generic approach is to let
PCI core handle the work.
e100_suspend() calls __e100_shutdown() to perform intermediate tasks.
__e100_shutdown() calls pci_save_state() which is not recommended.
e100_suspend() also calls __e100_power_off() which is calling PCI helper
functions, pci_prepare_to_sleep(), pci_set_power_state(), along with
pci_wake_from_d3(...,false). Hence, the functin call is removed and wol is
disabled as earlier using device_wakeup_disable().
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We observed two panics involving races with igb_reset_task.
The first panic is caused by this race condition:
kworker reboot -f
igb_reset_task
igb_reinit_locked
igb_down
napi_synchronize
__igb_shutdown
igb_clear_interrupt_scheme
igb_free_q_vectors
igb_free_q_vector
adapter->q_vector[v_idx] = NULL;
napi_disable
Panics trying to access
adapter->q_vector[v_idx].napi_state
The second panic (a divide error) is caused by this race:
kworker reboot -f tx packet
igb_reset_task
__igb_shutdown
rtnl_lock()
...
igb_clear_interrupt_scheme
igb_free_q_vectors
adapter->num_tx_queues = 0
...
rtnl_unlock()
rtnl_lock()
igb_reinit_locked
igb_down
igb_up
netif_tx_start_all_queues
dev_hard_start_xmit
igb_xmit_frame
igb_tx_queue_mapping
Panics on
r_idx % adapter->num_tx_queues
This commit applies to igb_reset_task the same changes that
were applied to ixgbe in commit 2f90b8657e ("ixgbe: this patch
adds support for DCB to the kernel and ixgbe driver"),
commit 8f4c5c9fb8 ("ixgbe: reinit_locked() should be called with
rtnl_lock") and commit 88adce4ea8 ("ixgbe: fix possible race in
reset subtask").
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After 'commit e086ba2fcc ("e1000e: disable s0ix entry and exit flows
for ME systems")',
ThinkPad P14s always failed to disable ULP by ME.
'commit 0c80cdbf33 ("e1000e: Warn if disabling ULP failed")'
break out of init phy:
error log:
[ 42.364753] e1000e 0000:00:1f.6 enp0s31f6: Failed to disable ULP
[ 42.524626] e1000e 0000:00:1f.6 enp0s31f6: PHY Wakeup cause - Unicast Packet
[ 42.822476] e1000e 0000:00:1f.6 enp0s31f6: Hardware Error
When disable s0ix, E1000_FWSM_ULP_CFG_DONE will never be 1.
If continue to init phy like before, it can work as before.
iperf test result good too.
Fixes: 0c80cdbf33 ("e1000e: Warn if disabling ULP failed")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
The driver was invoking PCI helper functions like pci_save/restore_state(),
and pci_enable/disable_device(), which is not recommended.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With legacy PM hooks, it was the responsibility of a driver to manage PCI
states and also the device's power state. The generic approach is to let
PCI core handle the work.
ixgbe_suspend() calls __ixgbe_shutdown() to perform intermediate tasks.
__ixgbe_shutdown() modifies the value of "wake" (device should be wakeup
enabled or not), responsible for controlling the flow of legacy PM.
Since, PCI core has no idea about the value of "wake", new code for generic
PM may produce unexpected results. Thus, use "device_set_wakeup_enable()"
to wakeup-enable the device accordingly.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove legacy PM callbacks and use generic operations. With legacy code,
drivers were responsible for handling PCI PM operations like
pci_save_state(). In generic code, all these are handled by PCI core.
The generic suspend() and resume() are called at the same point the legacy
ones were called. Thus, it does not affect the normal functioning of the
driver.
__maybe_unused attribute is used with .resume() but not with .suspend(), as
.suspend() is called by .shutdown().
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With the support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI states
changes and device's power state themselves. The required operations are
done by PCI core.
PCI drivers are not expected to invoke PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(),
pci_set_power_state(), etc. Their tasks are completed by PCI core itself.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
RX queue IRQ mappings are disposed in both the TX IRQ and RX IRQ
error paths. Fix this and dispose of TX IRQ mappings correctly in
case of an error.
Fixes: ea22d51a78 ("ibmvnic: simplify and improve driver probe function")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2020-07-29
This series contains updates to the ice driver only.
Dave works around LFC settings not being preserved through link events.
Fixes link issues with GLOBR reset and handling of multiple link events.
Nick restores VF MSI-X after PCI reset.
Kiran corrects the error code returned in ice_aq_sw_rules if the rule
does not exist.
Paul prevents overwriting of user set descriptors.
Tarun adds masking before accessing rate limiting profile types and
corrects queue bandwidth configuration.
Victor modifies Tx queue scheduler distribution to spread more evenly
across queue group nodes.
Krzysztof sets need_wakeup flag for Tx AF_XDP.
Brett allows VLANs in safe mode.
Marcin cleans up VSIs on probe failure.
Bruce reduces the scope of a variable.
Ben removes a FW workaround.
Tony fixes an unused parameter warning.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta has switched to phylink, so the comment should look
like "We may have called phylink_speed_down before".
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lifetime of the Rx listener item ('rxl_item') is managed using RCU,
but is dereferenced outside of RCU read-side critical section, which can
lead to a use-after-free.
Fix this by increasing the scope of the RCU read-side critical section.
Fixes: 93c1edb27f ("mlxsw: Introduce Mellanox switch driver core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited commit mistakenly removed the trap group for externally routed
packets (e.g., via the management interface) and grouped locally routed
and externally routed packet traps under the same group, thereby
subjecting them to the same policer.
This can result in problems, for example, when FRR is restarted and
suddenly all transient traffic is trapped to the CPU because of a
default route through the management interface. Locally routed packets
required to re-establish a BGP connection will never reach the CPU and
the routing tables will not be re-populated.
Fix this by using a different trap group for externally routed packets.
Fixes: 8110668ecd ("mlxsw: spectrum_trap: Register layer 3 control traps")
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited commit added the ability to program link-local prefix routes to
the ASIC so that relevant packets are routed and trapped correctly.
However, host routes were not included in the change and thus not
programmed to the ASIC. This can result in packets being trapped via an
external route trap instead of a local route trap as in IPv4.
Fix this by programming all the link-local routes to the ASIC.
Fixes: 10d3757fcb ("mlxsw: spectrum_router: Allow programming link-local prefix routes")
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit cited below removed the RCU read-side critical section from
rtnl_fdb_dump() which means that the ndo_fdb_dump() callback is invoked
without RCU protection.
This results in the following warning [1] in the VXLAN driver, which
relied on the callback being invoked from an RCU read-side critical
section.
Fix this by calling rcu_read_lock() in the VXLAN driver, as already done
in the bridge driver.
[1]
WARNING: suspicious RCU usage
5.8.0-rc4-custom-01521-g481007553ce6 #29 Not tainted
-----------------------------
drivers/net/vxlan.c:1379 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by bridge/166:
#0: ffffffff85a27850 (rtnl_mutex){+.+.}-{3:3}, at: netlink_dump+0xea/0x1090
stack backtrace:
CPU: 1 PID: 166 Comm: bridge Not tainted 5.8.0-rc4-custom-01521-g481007553ce6 #29
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
dump_stack+0x100/0x184
lockdep_rcu_suspicious+0x153/0x15d
vxlan_fdb_dump+0x51e/0x6d0
rtnl_fdb_dump+0x4dc/0xad0
netlink_dump+0x540/0x1090
__netlink_dump_start+0x695/0x950
rtnetlink_rcv_msg+0x802/0xbd0
netlink_rcv_skb+0x17a/0x480
rtnetlink_rcv+0x22/0x30
netlink_unicast+0x5ae/0x890
netlink_sendmsg+0x98a/0xf40
__sys_sendto+0x279/0x3b0
__x64_sys_sendto+0xe6/0x1a0
do_syscall_64+0x54/0xa0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fe14fa2ade0
Code: Bad RIP value.
RSP: 002b:00007fff75bb5b88 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00005614b1ba0020 RCX: 00007fe14fa2ade0
RDX: 000000000000011c RSI: 00007fff75bb5b90 RDI: 0000000000000003
RBP: 00007fff75bb5b90 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00005614b1b89160
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
Fixes: 5e6d243587 ("bridge: netlink dump interface at par with brctl")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on PAGE_SIZE, the following unused parameter warning can be
reported:
drivers/net/ethernet/intel/ice/ice_txrx.c: In function ‘ice_rx_frame_truesize’:
drivers/net/ethernet/intel/ice/ice_txrx.c:513:21: warning: unused parameter ‘size’ [-Wunused-parameter]
unsigned int size)
The 'size' variable is used only when PAGE_SIZE >= 8192. Add __maybe_unused
to remove the warning.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
For the FW logging info AQ command, we currently set the ICE_AQ_FLAG_RD
in order to work around a FW issue. This issue has been fixed so remove the
workaround.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The scope of the macro local variable 'i' can be reduced. Do so to avoid
static analysis tools from complaining.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As part of ice_setup_pf_sw() a PF VSI is setup; release the VSI in case of
failure.
Signed-off-by: Marcin Szycik <marcin.szycik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the PF VSI's context parameters are left in a bad state when
going into safe mode. This is causing VLAN traffic to not pass. Fix this
by configuring the PF VSI to allow all VLAN tagged traffic.
Also, remove redundant comment explaining the safe mode flow in
ice_probe().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This is a port of i40e commit 705639572e ("i40e: need_wakeup flag might
not be set for Tx").
Quoting the original commit message:
"The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an interrupt
since interrupts are disabled in the napi poll loop) between the time we
stopped processing the Tx completions and interrupts are enabled again.
In this case, the need_wakeup flag will have been cleared at the end of
the Tx completion processing as we believe we will get an interrupt from
the outstanding completion at a later point in time. But if this
completion interrupt occurs before interrupts are enable, we lose it and
should at that point really have set the need_wakeup flag since there
are no more outstanding completions that can generate an interrupt to
continue the processing. When this happens, user space will see a Tx
queue need_wakeup of 0 and skip issuing a syscall, which means will
never get into the Tx processing again and we have a deadlock."
As a result, packet processing stops. This patch introduces a fix for
this issue, by always setting the need_wakeup flag at the end of an
interrupt processing. This ensures that the deadlock will not happen.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Distribute the Tx queues evenly across all queue groups. This will
help the queues to get more equal sharing among the queues when all
are in use.
In the previous algorithm, the next queue group node will be picked up
only after the previous one filled with max children.
For example: if VSI is configured with 9 queues, the first 8 queues
will be assigned to queue group 1 and the 9th queue will be assigned to
queue group 2.
The 2 queue groups split the bandwidth between them equally (50:50).
The first queue group node will share the 50% bandwidth with all of
its children (8 queues). And the second queue group node will share
the entire 50% bandwidth with its only children.
The new algorithm will fix this issue.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
By default the queues are configured in legacy mode. The default
BW settings for legacy/advanced modes are different. The existing
code was using the advanced mode default value of 1 which was
incorrect. This caused the unbalanced BW sharing among siblings.
The recommended default value is applied.
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mask bits before accessing the profile type field.
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If a user sets the value of the TX or RX descriptors to some non-default
value using 'ethtool -G' then we need to not overwrite the values when
we rebuild the VSI. The VSI rebuild could happen as a result of a user
setting the number of queues via the 'ethtool -L' command. Fix this by
checking to see if the value we have stored is non-zero and if it is
then don't change the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Return ICE_ERR_DOES_NOT_EXIST return code if admin command error code is
ICE_AQ_RC_ENOENT (not exist). ice_aq_sw_rules is used when switch
rule is getting added/deleted/updated. In case of delete/update
switch rule, admin command can return ICE_AQ_RC_ENOENT error code
if such rule does not exist, hence return ICE_ERR_DOES_NOT_EXIST error
code from ice_aq_sw_rule, so that caller of this function can decide
how to handle ICE_ERR_DOES_NOT_EXIST.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
During a PCI FLR the MSI-X Enable flag in the VF PCI MSI-X capability
register will be cleared. This can lead to issues when a VF is
assigned to a VM because in these cases the VF driver receives no
indication of the PF PCI error/reset and additionally it is incapable
of restoring the cleared flag in the hypervisor configuration space
without fully reinitializing the driver interrupt functionality.
Since the VF driver is unable to easily resolve this condition on its own,
restore the VF MSI-X flag during the PF PCI reset handling.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the driver experiences a link event (especially link up)
there can be multiple events generated. Some of these are
link fault and still have a state of DOWN set. The problem
happens when the link comes UP during the PF driver handling
one of the LINK DOWN events. The status of the link is updated
and is now seen as UP, so when the actual LINK UP event comes,
the port information has already been updated to be seen as UP,
even though none of the UP activities have been completed.
After the link information has been updated in the link
handler and evaluated for MEDIA PRESENT, if the state
of the link has been changed to UP, treat the DOWN event
as an UP event since the link is now UP.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After a GLOBR, the link was broken so that a link
up situation was being seen as a link down.
The problem was that the rebuild process was updating
the port_info link status without doing any of the
other things that need to be done when link changes.
This was causing the port_info struct to have current
"UP" information so that any further UP interrupts
were skipped as redundant.
The rebuild flow should *not* be updating the port_info
struct link information, so eliminate this and leave
it to the link event handling code.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a bug where the LFC settings are not being preserved
through a link event. The registers in question are the ones
that are touched (and restored) when a set_local_mib AQ command
is performed.
On a link-up event, make sure that a set_local_mib is being
performed.
Move the function ice_aq_set_lldp_mib() from the DCB specific
ice_dcb.c to ice_common.c so that the driver always has access
to this AQ command.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When WoL is enabled and the machine is powered off, the PHY remains
waiting for wakeup events at max speed, which is a waste of energy.
Slow down the PHY speed before stopping the ethernet if WoL is enabled,
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the stmmac driver WOL implementation relies on MAC's PMT
feature. We have a case: the MAC HW doesn't enable PMT, instead, we
rely on the phy to support WOL. Implement the support for this case.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to prepare WOL support with phy. Compared with WOL
implementation which relies on the MAC's PMT features, in phy
supported WOL case, device_may_wakeup() may also be true, but we
should not call mac's pmt() function if HW doesn't enable PMT.
And during resume, we should call phylink_start() if PMT is disabled.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If !device_can_wakeup(), there's no need to futher check. And return
-EOPNOTSUPP rather than -EINVAL if !device_can_wakeup().
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove WAKE_MAGIC from supported modes if the HW capability register
shows no support for pmt_magic_frame.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alter the rtl8366_vlan_add() to call rtl8366_set_vlan()
inside the loop that goes over all VIDs since we now
properly support calling that function more than once.
Augment the loop to postincrement as this is more
intuitive.
The loop moved past the last VID but called
rtl8366_set_vlan() with the port number instead of
the VID, assuming a 1-to-1 correspondence between
ports and VIDs. This was also a bug.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8366 would not handle adding new members (ports) to
a VLAN: the code assumed that ->port_vlan_add() was only
called once for a single port. When intializing the
switch with .configure_vlan_while_not_filtering set to
true, the function is called numerous times for adding
all ports to VLAN1, which was something the code could
not handle.
Alter rtl8366_set_vlan() to just |= new members and
untagged flags to 4k and MC VLAN table entries alike.
This makes it possible to just add new ports to a
VLAN.
Put in some helpful debug code that can be used to find
any further bugs here.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multiproto mode, bareudp_xmit() accepts sending multicast MPLS and
IPv6 packets regardless of the bareudp ethertype. In practice, this
let an IP tunnel send multicast MPLS packets, or an MPLS tunnel send
IPv6 packets.
We need to restrict the test further, so that the multiproto mode only
enables
* IPv6 for IPv4 tunnels,
* or multicast MPLS for unicast MPLS tunnels.
To improve clarity, the protocol validation is moved to its own
function, where each logical test has its own condition.
v2: s/ntohs/htons/
Fixes: 4b5f67232d ("net: Special handling for IP & MPLS.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
improve the error message when functions return failure and dump
relevant registers in some exception handling processes
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add support to handle hw abnormal event such as hardware failure,
cable unplugged,link error
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added unregister_netdev in the driver remove
function. Generally unregister_netdev is called
after disabling all the device interrupts but here
it is called before disabling device mailbox
interrupts. The reason behind this is VF needs
mailbox interrupt to communicate with its PF to
clean up its resources during otx2_stop.
otx2_stop disables packet I/O and queue interrupts
first and by using mailbox interrupt communicates
to PF to free VF resources. Hence this patch
calls unregister_device just before
disabling mailbox interrupts.
Fixes: 3184fb5ba9 ("octeontx2-vf: Virtual function driver support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver exit cancel the queued
reset_task work in VF driver.
Fixes: 3184fb5ba9 ("octeontx2-vf: Virtual function driver support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two bugs exist in the code related to reset_task
in PF driver one is the missing protection
against network stack ndo_open and ndo_close.
Other one is the missing cancel_work.
This patch fixes those problems.
Fixes: 4ff7d1488a ("octeontx2-pf: Error handling support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new SSR notifier infrastructure to request notifications of
modem events, rather than the remoteproc IPA notification system.
The latter was put in place temporarily with the knowledge that the
new mechanism would become available.
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200724181142.13581-2-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use the newly added pldmfw library to implement device flash update for
the Intel ice networking device driver. This support uses the devlink
flash update interface.
The main parts of the flash include the Option ROM, the netlist module,
and the main NVM data. The PLDM firmware file contains modules for each
of these components.
Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.
The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset (which would usually occur during
the next reboot).
Although the firmware AdminQ interface does report an immediate status
for each command, the NVM erase and NVM write commands receive status
asynchronously. The driver must not continue writing until previous
erase and write commands have finished. The real status of the NVM
commands is returned over the receive AdminQ. Implement a simple
interface that uses a wait queue so that the main update thread can
sleep until the completion status is reported by firmware. For erasing
the inactive banks, this can take quite a while in practice.
To help visualize the process to the devlink application and other
applications based on the devlink netlink interface, status is reported
via the devlink_flash_update_status_notify. While we do report status
after each 4k block when writing, there is no real status we can report
during erasing. We simply must wait for the complete module erasure to
finish.
With this implementation, basic flash update for the ice hardware is
supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a flash update, the pending status of the update can be determined
from the device capabilities.
Read the appropriate device capability and store whether there is
a pending update awaiting a reboot.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add structures, identifiers, and helper functions for several AdminQ
commands related to performing a firmware update for the ice hardware.
These will be used in future code for implementing the devlink
.flash_update handler.
Signed-off-by: Cudzilo, Szymon T <szymon.t.cudzilo@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends function parsing response from Discover Device
Capability AQC to check if the device supports unified NVM update flow.
Signed-off-by: Jacek Naczyk <jacek.naczyk@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify mtk_gmac0_rgmii_adjust() so it can always be called.
mtk_gmac0_rgmii_adjust() sets-up the TRGMII clocks.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-By: David Woodhouse <dwmw2@infradead.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl8ggswACgkQSD+KveBX
+j7yOgf8DjzPtSpVfUA7Iq28WO6YxJy208oUdLjKNuRNr74vXulHegNlP6cFDHU3
QIddvTBNMTp2BpJpoFMbEod7sVTBq5KVQZvpIuFM2JU4h76vL4cYbWeBuT6rFIoJ
m5vuuUyAB+16QbJzagY/rqfQMs0w7KnR+Zhv18JzwyHhBiRLaPzYdmSWM2kkF8HZ
3DrY8RWgkeaI9vTpE6Fau7BRNDUOMgjIahiUrojJuyPsYZpJf5g+KaMj4xvgcqMa
vaPaw8iHN7+N3KIdcf6MJhfzx3SHP5YNieU/MfvE9sLvdPvfLETdpexYPB8b0/vs
L9w2D8j0uZyXek30fIiIwHaibQGZPw==
=W0Fn
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-07-28' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes-2020-07-28
This series introduces some fixes to mlx5 driver.
v1->v2:
- Drop the "Hold reference on mirred devices" patch, until Or's
comments are addressed.
- Imporve "Modify uplink state" patch commit message per Or's request.
Please pull and let me know if there is any problem.
For -Stable:
For -stable v4.9
('net/mlx5e: Fix error path of device attach')
For -stable v4.15
('net/mlx5: Verify Hardware supports requested ptp function on a given
pin')
For -stable v5.3
('net/mlx5e: Modify uplink state on interface up/down')
For -stable v5.4
('net/mlx5e: Fix kernel crash when setting vf VLANID on a VF dev')
('net/mlx5: E-switch, Destroy TSAR when fail to enable the mode')
For -stable v5.5
('net/mlx5: E-switch, Destroy TSAR after reload interface')
For -stable v5.7
('net/mlx5: Fix a bug of using ptp channel index as pin index')
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the bogus endpoint-lookup helper which could end up accepting
interfaces based on endpoints belonging to unrelated altsettings.
Note that the returned bulk pipes and interrupt endpoint descriptor
were never actually used. Instead the bulk-endpoint numbers are
hardcoded to 1 and 2 (matching the specification), while the interrupt-
endpoint descriptor was assumed to be the third descriptor created by
USB core.
Try to bring some order to this by dropping the bogus lookup helper and
adding the missing endpoint sanity checks while keeping the interrupt-
descriptor assumption for now.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt URB transfer-buffer was never freed on disconnect or after
probe errors.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing endpoint sanity check to prevent a NULL-pointer
dereference should a malicious device lack the expected endpoints.
Note that the driver has a broken endpoint-lookup helper,
lan78xx_get_endpoints(), which can end up accepting interfaces in an
altsetting without endpoints as long as *some* altsetting has a bulk-in
and a bulk-out endpoint.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow QSFP-DD transceivers temperature thresholds reading for hardware
monitoring and thermal control.
For this type, the thresholds are located in page 02h according to the
"Module and Lane Thresholds" description from Common Management
Interface Specification.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Quad Small Form Factor Pluggable Double Density (QSFP-DD) hardware
specification defines a form factor that supports up to 400 Gbps in
aggregate over an 8x50-Gbps electrical interface. The QSFP-DD supports
both optical and copper interfaces.
Implementation is based on Common Management Interface Specification;
Rev 4.0 May 8, 2019. Table 8-2 "Identifier and Status Summary (Lower
Page)" from this spec defines "Id and Status" fields located at offsets
00h - 02h. Bit 2 at offset 02h ("Flat_mem") specifies QSFP EEPROM memory
mode, which could be "upper memory flat" or "paged". Flat memory mode is
coded "1", and indicates that only page 00h is implemented in EEPROM.
Paged memory is coded "0" and indicates that pages 00h, 01h, 02h, 10h
and 11h are implemented. Pages 10h and 11h are currently not supported
by the driver.
"Flat" memory mode is used for the passive copper transceivers. For this
type only page 00h (256 bytes) is available. "Paged" memory is used for
the optical transceivers. For this type pages 00h (256 bytes), 01h (128
bytes) and 02h (128 bytes) are available. Upper page 01h contains static
advertising field, while upper page 02h contains the module-defined
thresholds and lane-specific monitors.
Extend enumerator 'mlxsw_reg_mcia_eeprom_module_info_id' with additional
field 'MLXSW_REG_MCIA_EEPROM_MODULE_INFO_TYPE_ID'. This field is used to
indicate for QSFP-DD transceiver type which memory mode is to be used.
Expose 256 bytes buffer for QSFP-DD passive copper transceiver and
512 bytes buffer for optical.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Misc and small update to mlx5 driver:
1) Aya adds PCIe relaxed ordering support for mlx5 netdev queues.
2) Eran Refactors pages data base to be per vf/function to speedup
unload time.
3) Parav changes eswitch steering initialization to account for
tota_vports rather than for only active vports and
Link non uplink representors to PCI device, for uniform naming scheme.
4) Tariq, trivial RX code improvements and missing inidirect calls
wrappers.
5) Small cleanup patches
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl8f8fgACgkQSD+KveBX
+j5pgggAtjGZ3dWt43WNIMEYum/OZYrIhAVIaB4IgPY2Q90i26A7VMpBUOpQxTzk
Z+PYiSuiwplWeQ0k9GW2yMCAEACsuiSQXQG/eUA4jKRKf9hQEXi5guuVEIYJRm68
uL4aI4m4Aygx/n2UTdajARB69RVZ02ZhoNucMGETw4gzvqLdSgVCyR2tiDnPiKKW
3+y9nViglik7XqvDrYT9H+7vo8geCg5zBWEABy/Ls0VUCWN2xCjPNbGL9VCMG8Q+
A6n5SdhaOMIc9u5vkcE4CVgOnUPwNPQeu+GVgEodZ7GhFwX897A8dvFwljfML/UU
rBRPgC2kUTtGDZxVcSBMlBjrXl6zMQ==
=iwh/
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-07-28' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-07-28
Misc and small update to mlx5 driver:
1) Aya adds PCIe relaxed ordering support for mlx5 netdev queues.
2) Eran Refactors pages data base to be per vf/function to speedup
unload time.
3) Parav changes eswitch steering initialization to account for
tota_vports rather than for only active vports and
Link non uplink representors to PCI device, for uniform naming scheme.
4) Tariq, trivial RX code improvements and missing inidirect calls
wrappers.
5) Small cleanup patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The .suspend() and .resume() callbacks are not defined for this driver.
Still, their power management structure follows the legacy framework. To
bring it under the generic framework, simply remove the binding of
callbacks from "struct pci_driver".
Change code indentation from space to tab in "struct pci_driver".
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the PF interface up/down, notify the firmware to update
uplink state via MODIFY_VPORT_STATE, when E-Switch is enabled.
This behavior will prevent sending traffic out on uplink port when PF is
down, such as sending traffic from a VF interface which is still up.
Currently when calling mlx5e_open/close(), the driver only sends PAOS
command to notify the firmware to set the physical port state to
up/down, however, it is not sufficient. When VF is in "auto" state, it
follows the uplink state, which was not updated on mlx5e_open/close()
before this patch.
When switchdev mode is enabled and uplink representor is first enabled,
set the uplink port state value back to its FW default "AUTO".
Fixes: 63bfd399de ("net/mlx5e: Send PAOS command on interface up/down")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In a special configuration, a ConnectX6-Dx pin pps-out might be activated
when driver is loaded. Fix the driver to always read the operational pin
mode when registering it, and advertise it accordingly.
Fixes: ee7f12205a ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5e_rep_is_lag_netdev is used as first check as part of netdev events
handler for bond device of non-uplink representors, this handler can get
any netdevice under the same network namespace of mlx5e netdevice. Current
code treats the netdev as mlx5e netdev and only later on verifies this,
hence causes the following Kasan trace:
[15402.744990] ==================================================================
[15402.746942] BUG: KASAN: slab-out-of-bounds in mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.749009] Read of size 8 at addr ffff880391f3f6b0 by task ovs-vswitchd/5347
[15402.752065] CPU: 7 PID: 5347 Comm: ovs-vswitchd Kdump: loaded Tainted: G B O --------- -t - 4.18.0-g3dcc204d291d-dirty #1
[15402.755349] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[15402.757600] Call Trace:
[15402.758968] dump_stack+0x71/0xab
[15402.760427] print_address_description+0x6a/0x270
[15402.761969] kasan_report+0x179/0x2d0
[15402.763445] ? mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.765121] mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.766782] mlx5e_rep_esw_bond_netevent+0x129/0x620 [mlx5_core]
Fix by deferring the violating access to be post the netdev verify check.
Fixes: 7e51891a23 ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix a bug where driver did not verify Hardware pin capabilities for
PTP functions.
Fixes: ee7f12205a ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On PTP mlx5_ptp_enable(on=0) flow, driver mistakenly used channel index
as pin index.
After ptp patch marked in fixes tag was introduced, driver can freely
call ptp_find_pin() as part of the .enable() callback.
Fix driver mlx5_ptp_enable(on=0) flow to always use ptp_find_pin(). With
that, Driver will use the correct pin index in mlx5_ptp_enable(on=0) flow.
In addition, when initializing the pins, always set channel to zero. As
all pins can be attached to all channels, let ptp_set_pinfunc() to move
them between the channels.
For stable branches, this fix to be applied only on kernels that includes
both patches in fixes tag. Otherwise, mlx5_ptp_enable(on=0) will be stuck
on pincfg_mux.
Fixes: 62582a7ee7 ("ptp: Avoid deadlocks in the programmable pin code.")
Fixes: ee7f12205a ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cited commit add initialization of ethtool steering during
representor rx initializations without cleaning it up in representor
rx cleanup, this may cause for stale ethtool flows to remain after
moving back from switchdev mode to legacy mode.
Fixed by calling ethtool steering cleanup during rep rx cleanup.
Fixes: 6783e8b29f ("net/mlx5e: Init ethtool steering for representors")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On failure to attach the netdev, fix the rollback by re-setting the
device's state back to MLX5E_STATE_DESTROYING.
Failing to attach doesn't stop statistics polling via .ndo_get_stats64.
In this case, although the device is not attached, it falsely continues
to query the firmware for counters. Setting the device's state back to
MLX5E_STATE_DESTROYING prevents the firmware counters query.
Fixes: 26e59d8077 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The steering tree is as follow (nic RX as example):
---------
|root_ns|
---------
|
--------------------------------
| | |
---------- ---------- ---------
|p(prio)0| | p1 | | pn |
---------- ---------- ---------
| |
---------------- ---------------
|ns(e.g bypass)| |ns(e.g. lag) |
---------------- ---------------
| | |
---- ---- ----
|p0| |p1| |pn|
---- ---- ----
|
----
|FT|
----
find_next_chained_ft(prio) returns the first flow table in the next
priority. If prio is a parent of a flow table then it returns the first
flow table in the next priority in the same namespace, else if prio
is parent of namespace, then it should return the first flow table
in the next namespace. Currently if the user requests to forward to
next namespace, the code calls to find_next_chained_ft with the prio
of the next namespace and not the prio of the namesapce itself.
Fixes: 9254f8ed15 ("net/mlx5: Add support in forward to namespace")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When eswitch offloads is enabled, TSAR is created before reloading
the interfaces.
However when eswitch offloads mode is disabled, TSAR is disabled before
reloading the interfaces.
To keep the eswitch enable/disable sequence as mirror, destroy TSAR
after reloading the interfaces.
Fixes: 1bd27b11c1 ("net/mlx5: Introduce E-switch QoS management")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When either esw_legacy_enable() or esw_offloads_enable() fails,
code missed to destroy the created TSAR.
Hence, add the missing call to destroy the TSAR.
Fixes: 610090ebce ("net/mlx5: E-switch, Initialize TSAR Qos hardware block before its user vports")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When device is resetting or reset failed, firmware is unable to
handle mailbox. VLAN should not be configured in this case.
Fixes: fe4144d47e ("net: hns3: sync VLAN filter entries when kill VLAN ID failed")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user had created a FD rule, all the aRFS rules should be clear up.
HNS3 process flow as below:
1.get spin lock of fd_ruls_list
2.clear up all aRFS rules
3.release lock
4.get spin lock of fd_ruls_list
5.creat a rules
6.release lock;
There is a short period of time between step 3 and step 4, which would
creatting some new aRFS FD rules if driver was receiving packet.
So refactor the fd_rule_lock to fix it.
Fixes: 4412288757 ("net: hns3: refine the flow director handle")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hclgevf_update_port_base_vlan_info() may be called when
VF is resetting, which may cause hns3_nic_net_open() being called
twice unexpectedly.
So fix it by adding a reset check for it, and extend critical
region for rntl_lock in hclgevf_update_port_base_vlan_info().
Fixes: 92f11ea177 ("net: hns3: fix set port based VLAN issue for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the queue depth and queue parameters are modified, there is
a low probability that TX timeout occurs. The two operations cause
the link to be down or up when the watchdog is still working. All
queues are stopped when the link is down. After the carrier is on,
all queues are woken up. If the watchdog detects the link between
the carrier on and wakeup queues, a false TX timeout occurs.
So fix this issue by modifying the sequence of carrier on and queue
wakeup, which is symmetrical to the link down action.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The linear and frag data part may be changed when the skb is expanded
or lineared in skb_cow_head() or skb_checksum_help(), which is called
by hns3_fill_skb_desc(), so the linear len return by skb_headlen()
before the calling of hns3_fill_skb_desc() is unreliable.
Move hns3_fill_skb_desc() before the calling of skb_headlen() to fix
this bug.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
list_for_each_entry is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
Note that list_for_each_entry is defined in terms of list_first_entry,
which indicates that it should not be used on an empty list. But in
list_for_each_entry, the element obtained by list_first_entry is not
really accessed, only the address of its list_head field is compared
to the address of the list head, so the list_first_entry is safe.
The semantic patch that makes this change is as follows (with another
variant for the no brace case): (http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
iterator name list_for_each_entry;
statement S;
identifier i;
@@
-if (!(list_empty(x))) {
list_for_each_entry(i,x,...) S
- }
... when != i
? i = e
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There is no need to print on each unsuccessful matcher
ip_version combination since it probably will happen when
trying to create all the possible combinations.
On a real failure we have a print in the calling function.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The concept of Relaxed Ordering in the PCI Express environment allows
switches in the path between the Requester and Completer to reorder some
transactions just received before others that were previously enqueued.
In ETH driver, there is no question of write integrity since each memory
segment is written only once per cycle. In addition, the driver doesn't
access the memory shared with the hardware until the corresponding CQE
arrives indicating all PCI transactions are done.
Running TCP single stream over ConnectX-4 LX, ARM CPU on remote-numa has
300% improvement in the bandwidth.
With relaxed ordering turned off: BW:10 [GB/s]
With relaxed ordering turned on: BW:40 [GB/s]
The driver turns relaxed ordering with respect to the firmware
capabilities and the return value from pcie_relaxed_ordering_enabled().
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use the indirect call wrapper API macros for declaration and scope
of the RX post WQEs functions.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Instead of exposing the RQ datapath handlers (from en_rx.c) so that
they are set in the control path (in en_main.c), wrap this logic
in a single function in en_rx.c and expose it alone.
Every profile will now have a pointer to the new mlx5e_rx_handlers
structure, instead of directly pointing to the previously-exposed
RQ handlers.
This significantly improves locality and modularity of the driver,
and allows many functions in en_rx.c to become static.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently PF and VF representors are exposed as virtual device.
They are not linked to its parent PCI device like how uplink
representor is linked.
Due to this, PF and VF representors cannot benefit of the
systemd defined naming scheme. This requires special handling
by the users.
Hence, link the PF and VF representors to their parent PCI device
similar to existing uplink representor netdevice.
Example:
udevadm output before linking to PCI device:
$ udevadm test-builtin net_id /sys/class/net/eth6
Load module index
Network interface NamePolicy= disabled on kernel command line, ignoring.
Parsed configuration file /usr/lib/systemd/network/99-default.link
Created link configuration context.
Using default interface naming scheme 'v243'.
ID_NET_NAMING_SCHEME=v243
Unload module index
Unloaded link configuration context.
udevadm output after linking to PCI device:
$ udevadm test-builtin net_id /sys/class/net/eth6
Load module index
Network interface NamePolicy= disabled on kernel command line, ignoring.
Parsed configuration file /usr/lib/systemd/network/99-default.link
Created link configuration context.
Using default interface naming scheme 'v243'.
ID_NET_NAMING_SCHEME=v243
ID_NET_NAME_PATH=enp0s8f0npf0vf0
Unload module index
Unloaded link configuration context.
In past there was little concern over seeing 10,000 lines output
showing up at thread [1] is not applicable as ndo ops for VF
handling is not exposed for all the 100 repesentors for mlx5 devices.
Additionally alternative device naming [2] to overcome shorter device
naming is also part of the latest systemd release v245.
[1] https://marc.info/?l=linux-netdev&m=152657949117904&w=2
[2] https://lwn.net/Articles/814068/
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently steering table and rx group initialization helper
routines works on the total_vports passed as input parameter.
Both eswitch helpers work on the mlx5_eswitch and thereby have access
to esw->total_vports. Hence use it directly instead of passing it
via function input arguments.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Total e-switch vports are already stored in mlx5_eswitch total_vports.
Avoid copy of it in nvports and reuse existing total_vports calculation.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When eswitch is enabled, VFs might not be enabled. Hence, consider
maximum number of VFs.
This further closes the gap between handling VF vports between ECPF and
PF.
Fixes: ea2128fd63 ("net/mlx5: E-switch, Reduce dependency on num_vfs during mode set")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add function ID to reclaim pages debug log for better user visibility.
Signed-off-by: Avihu Hagag <avihuh@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Per page request event, FW request to allocated or release pages for a
single function. Driver maintains FW pages object per function, so there
is no need to hold one global page data-base. Instead, have a page
data-base per function, which will improve performance release flow in all
cases, especially for "release all pages".
As the range of function IDs is large and not sequential, use xarray to
store a per function ID page data-base, where the function ID is the key.
Upon first allocation of a page to a function ID, create the page
data-base per function. This data-base will be released only at pagealloc
mechanism cleanup.
NIC: ConnectX-4 Lx
CPU: Intel(R) Xeon(R) CPU E5-2650 v2 @ 2.60GHz
Test case: 32 VFs, measure release pages on one VF as part of FLR
Before: 0.021 Sec
After: 0.014 Sec
The improvement depends on amount of VFs and memory utilization
by them. Time measurements above were taken from idle system.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2020-07-27
This series contains updates to igc driver only.
Sasha cleans up double definitions, unneeded and non applicable
registers, and removes unused fields in structs. Ensures the Receive
Descriptor Minimum Threshold Count is cleared and fixes a static checker
error.
v2: Remove fields from hw_stats in patches that removed their uses.
Reworded patch descriptions for patches 1, 2, and 4.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In ef100_reset(), make the MCDI call to do the reset.
Also, do a reset at start-of-day during probe, to put the function in
a clean state.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC_CMD_GET_CAPABILITIES now has a third word of flags; extend the
efx_has_cap() machinery to cover it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently RX and TX-completion events are unhandled, as neither the RX
nor the TX path has been implemented yet.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Channels are probed, but actual event handling is still stubbed out.
Stub implementation of check_caps is needed because ptp.c will call into
it from efx_ptp_use_mac_tx_timestamps() to decide if it wants TXQs.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We handle everything ourselves in ef100_reset(), rather than relying on
the generic down/up routines.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't actually do the MCDI to probe it fully until we have working
MCDI, which comes later, but we need efx->phy_data to be allocated so
that when we get MCDI events the link-state change handler doesn't
NULL-dereference.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't actually do the efx_mcdi_reset() because we don't have MCDI yet.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No TX or RX path, no MCDI, not even an ifup/down handler.
Besides stubs, the bulk of the patch deals with reading the Xilinx
extended PCIe capability, which tells us where to find our BAR.
Though in the same module, EF100 has its own struct pci_driver,
which is named sfc_ef100.
A small number of additional nic_type methods are added; those in the
TX (tx_enqueue) and RX (rx_packet) paths are called through indirect
call wrappers to minimise the performance impact.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EF100 adds a few new valid addresses for efx_writed_page(), as well as
a Function Control Window in the BAR whose location is variable.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An MDIO-based n-way restart does not make sense for any of the NICs
supported by this driver, nor for the coming EF100.
Unlike on Falcon (which was already split off into a separate driver),
the PHY on all of Siena, EF10 and EF100 is managed by MC firmware.
While Siena can talk to the PHY over MDIO, doing so for anything other
than debugging purposes (mdio_mii_ioctl) is likely to confuse the
firmware.
(According to the SFC firmware team, this support was originally added
to the Siena driver early in the development of that product, before
it was decided to have firmware manage the PHY.)
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson