When this driver is built as a module, I cannot rmmod it after insmoding
it.
This is because that this driver calls ravb_mdio_init() at the time of
probe, and module->refcnt is incremented by alloc_mdio_bitbang() called
after that.
Therefore, even if ifup is not performed, the driver is in use and rmmod
cannot be performed.
$ lsmod
Module Size Used by
ravb 40960 1
$ rmmod ravb
rmmod: ERROR: Module ravb is in use
Call ravb_mdio_init() at open and free_mdio_bitbang() at close, thereby
rmmod is possible in the ifdown state.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yuusuke Ashizuka <ashiduka@fujitsu.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When devm_kcalloc() fails, dev should be freed just
like what we've done in the subsequent error paths.
Fixes: 7b78be48a8 ("net: systemport: Dynamically allocate number of TX rings")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns_nic_dev_probe allocates ndev, but not free it on
two error handling paths, which may lead to memleak.
Fixes: 63434888aa ("net: hns: net: hns: enet adds support of acpi")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Nothing earth shattering here, lots of small fixes (f.e. missing RCU
protection, bad ref counting, missing memset(), etc.) all over the
place:
1) Use get_file_rcu() in task_file iterator, from Yonghong Song.
2) There are two ways to set remote source MAC addresses in macvlan
driver, but only one of which validates things properly. Fix this.
From Alvin Šipraga.
3) Missing of_node_put() in gianfar probing, from Sumera
Priyadarsini.
4) Preserve device wanted feature bits across multiple netlink
ethtool requests, from Maxim Mikityanskiy.
5) Fix rcu_sched stall in task and task_file bpf iterators, from
Yonghong Song.
6) Avoid reset after device destroy in ena driver, from Shay
Agroskin.
7) Missing memset() in netlink policy export reallocation path, from
Johannes Berg.
8) Fix info leak in __smc_diag_dump(), from Peilin Ye.
9) Decapsulate ECN properly for ipv6 in ipv4 tunnels, from Mark
Tomlinson.
10) Fix number of data stream negotiation in SCTP, from David Laight.
11) Fix double free in connection tracker action module, from Alaa
Hleihel.
12) Don't allow empty NHA_GROUP attributes, from Nikolay Aleksandrov"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (46 commits)
net: nexthop: don't allow empty NHA_GROUP
bpf: Fix two typos in uapi/linux/bpf.h
net: dsa: b53: check for timeout
tipc: call rcu_read_lock() in tipc_aead_encrypt_done()
net/sched: act_ct: Fix skb double-free in tcf_ct_handle_fragments() error flow
net: sctp: Fix negotiation of the number of data streams.
dt-bindings: net: renesas, ether: Improve schema validation
gre6: Fix reception with IP6_TNL_F_RCV_DSCP_COPY
hv_netvsc: Fix the queue_mapping in netvsc_vf_xmit()
hv_netvsc: Remove "unlikely" from netvsc_select_queue
bpf: selftests: global_funcs: Check err_str before strstr
bpf: xdp: Fix XDP mode when no mode flags specified
selftests/bpf: Remove test_align leftovers
tools/resolve_btfids: Fix sections with wrong alignment
net/smc: Prevent kernel-infoleak in __smc_diag_dump()
sfc: fix build warnings on 32-bit
net: phy: mscc: Fix a couple of spelling mistakes "spcified" -> "specified"
libbpf: Fix map index used in error message
net: gemini: Fix missing free_netdev() in error path of gemini_ethernet_port_probe()
net: atlantic: Use readx_poll_timeout() for large timeout
...
23 fixes in 5 drivers (qla2xxx, ufs, scsi_debug, fcoe, zfcp). The
bulk of the changes are in qla2xxx and ufs and all are mostly small
and definitely don't impact the core.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX0CxgiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVI9AP40cRrH
p0wrE1fKUyj+LbtnWrrHUXsuknS3Sf58zyPeEAEA3qxxLspTxWgLuSnT/KC2gqFB
Kv/XJyKM9CnRg7Uo4mo=
=GRmA
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"23 fixes in 5 drivers (qla2xxx, ufs, scsi_debug, fcoe, zfcp). The bulk
of the changes are in qla2xxx and ufs and all are mostly small and
definitely don't impact the core"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (23 commits)
Revert "scsi: qla2xxx: Disable T10-DIF feature with FC-NVMe during probe"
Revert "scsi: qla2xxx: Fix crash on qla2x00_mailbox_command"
scsi: qla2xxx: Fix null pointer access during disconnect from subsystem
scsi: qla2xxx: Check if FW supports MQ before enabling
scsi: qla2xxx: Fix WARN_ON in qla_nvme_register_hba
scsi: qla2xxx: Allow ql2xextended_error_logging special value 1 to be set anytime
scsi: qla2xxx: Reduce noisy debug message
scsi: qla2xxx: Fix login timeout
scsi: qla2xxx: Indicate correct supported speeds for Mezz card
scsi: qla2xxx: Flush I/O on zone disable
scsi: qla2xxx: Flush all sessions on zone disable
scsi: qla2xxx: Use MBX_TOV_SECONDS for mailbox command timeout values
scsi: scsi_debug: Fix scp is NULL errors
scsi: zfcp: Fix use-after-free in request timeout handlers
scsi: ufs: No need to send Abort Task if the task in DB was cleared
scsi: ufs: Clean up completed request without interrupt notification
scsi: ufs: Improve interrupt handling for shared interrupts
scsi: ufs: Fix interrupt error message for shared interrupts
scsi: ufs-pci: Add quirk for broken auto-hibernate for Intel EHL
scsi: ufs-mediatek: Fix incorrect time to wait link status
...
clang static analysis reports this problem
b53_common.c:1583:13: warning: The left expression of the compound
assignment is an uninitialized value. The computed value will
also be garbage
ent.port &= ~BIT(port);
~~~~~~~~ ^
ent is set by a successful call to b53_arl_read(). Unsuccessful
calls are caught by an switch statement handling specific returns.
b32_arl_read() calls b53_arl_op_wait() which fails with the
unhandled -ETIMEDOUT.
So add -ETIMEDOUT to the switch statement. Because
b53_arl_op_wait() already prints out a message, do not add another
one.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netvsc_vf_xmit() / dev_queue_xmit() will call VF NIC’s ndo_select_queue
or netdev_pick_tx() again. They will use skb_get_rx_queue() to get the
queue number, so the “skb->queue_mapping - 1” will be used. This may
cause the last queue of VF not been used.
Use skb_record_rx_queue() here, so that the skb_get_rx_queue() called
later will get the correct queue number, and VF will be able to use
all queues.
Fixes: b3bf5666a5 ("hv_netvsc: defer queue selection to VF")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using vf_ops->ndo_select_queue, the number of queues of VF is
usually bigger than the synthetic NIC. This condition may happen
often.
Remove "unlikely" from the comparison of ndev->real_num_tx_queues.
Fixes: b3bf5666a5 ("hv_netvsc: defer queue selection to VF")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Truncation of DMA_BIT_MASK to 32-bit dma_addr_t is semantically safe,
but the compiler was warning because it was happening implicitly.
Insert explicit casts to suppress the warnings.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple of spelling mistakes in comment text. Fix these.
Signed-off-by: Kaige Li <likaige@loongson.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace alloc_etherdev_mq with devm_alloc_etherdev_mqs. In this way,
when probe fails, netdev can be freed automatically.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit
8dcf2ad39f ("net: atlantic: add hwmon getter for MAC temperature")
implemented a read callback with an udelay(10000U). This fails to
compile on ARM because the delay is >1ms. I doubt that it is needed to
spin for 10ms even if possible on x86.
>From looking at the code, the context appears to be preemptible so using
usleep() should work and avoid busy spinning.
Use readx_poll_timeout() in the poll loop.
Fixes: 8dcf2ad39f ("net: atlantic: add hwmon getter for MAC temperature")
Cc: Mark Starovoytov <mstarovoitov@marvell.com>
Cc: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most statistics in ena driver are incremented, meaning that a stat's
value is a sum of all increases done to it since driver/queue
initialization.
This patch makes all statistics this way, effectively making missed_tx
statistic incremental.
Also added a comment regarding rx_drops and tx_drops to make it
clearer how these counters are calculated.
Fixes: 11095fdb71 ("net: ena: add statistics for missed tx packets")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ena_del_napi_in_range() function unregisters the napi handler for
rings in a given range.
This function had the following WARN_ON macro:
WARN_ON(ENA_IS_XDP_INDEX(adapter, i) &&
adapter->ena_napi[i].xdp_ring);
This macro prints the call stack if the expression inside of it is
true [1], but the expression inside of it is the wanted situation.
The expression checks whether the ring has an XDP queue and its index
corresponds to a XDP one.
This patch changes the expression to
!ENA_IS_XDP_INDEX(adapter, i) && adapter->ena_napi[i].xdp_ring
which indicates an unwanted situation.
Also, change the structure of the function. The napi handler is
unregistered for all rings, and so there's no need to check whether the
index is an XDP index or not. By removing this check the code becomes
much more readable.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset work is scheduled by the timer routine whenever it
detects that a device reset is required (e.g. when a keep_alive signal
is missing).
When releasing device resources in ena_destroy_device() the driver
cancels the scheduling of the timer routine without destroying the reset
work explicitly.
This creates the following bug:
The driver is suspended and the ena_suspend() function is called
-> This function calls ena_destroy_device() to free the net device
resources
-> The driver waits for the timer routine to finish
its execution and then cancels it, thus preventing from it
to be called again.
If, in its final execution, the timer routine schedules a reset,
the reset routine might be called afterwards,and a redundant call to
ena_restore_device() would be made.
By changing the reset routine we allow it to read the device's state
accurately.
This is achieved by checking whether ENA_FLAG_TRIGGER_RESET flag is set
before resetting the device and making both the destruction function and
the flag check are under rtnl lock.
The ENA_FLAG_TRIGGER_RESET is cleared at the end of the destruction
routine. Also surround the flag check with 'likely' because
we expect that the reset routine would be called only when
ENA_FLAG_TRIGGER_RESET flag is set.
The destruction of the timer and reset services in __ena_shutoff() have to
stay, even though the timer routine is destroyed in ena_destroy_device().
This is to avoid a case in which the reset routine is scheduled after
free_netdev() in __ena_shutoff(), which would create an access to freed
memory in adapter->flags.
Fixes: 8c5c7abdeb ("net: ena: add power management ops to the ENA driver")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig help text contains the phrase "the the" in the help
text. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ARP monitor is used for link detection, ARP replies are
validated for all slaves (arp_validate=3) and fail_over_mac is set to
active, two slaves of an active-backup bond may get stuck in a state
where both of them are active and pass packets that they receive to
the bond. This state makes IPv6 duplicate address detection fail. The
state is reached thus:
1. The current active slave goes down because the ARP target
is not reachable.
2. The current ARP slave is chosen and made active.
3. A new slave is enslaved. This new slave becomes the current active
slave and can reach the ARP target.
As a result, the current ARP slave stays active after the enslave
action has finished and the log is littered with "PROBE BAD" messages:
> bond0: PROBE: c_arp ens10 && cas ens11 BAD
The workaround is to remove the slave with "going back" status from
the bond and re-enslave it. This issue was encountered when DPDK PMD
interfaces were being enslaved to an active-backup bond.
I would be possible to fix the issue in bond_enslave() or
bond_change_active_slave() but the ARP monitor was fixed instead to
keep most of the actions changing the current ARP slave in the ARP
monitor code. The current ARP slave is set as inactive and backup
during the commit phase. A new state, BOND_LINK_FAIL, has been
introduced for slaves in the context of the ARP monitor. This allows
administrators to see how slaves are rotated for sending ARP requests
and attempts are made to find a new active slave.
Fixes: b2220cad58 ("bonding: refactor ARP active-backup monitor")
Signed-off-by: Jiri Wiesner <jwiesner@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every iteration of for_each_available_child_of_node() decrements
reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in gianfar.c by inserting of_node_put()
before the goto statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even after Tx queues are marked stopped, there exists a
small window where the current packet in the normal Tx
path is still being sent out and loopback selftest ends
up corrupting the same Tx ring. So, ensure selftest takes
the Tx lock to synchronize access the Tx ring.
Fixes: 7235ffae3d ("cxgb4: add loopback ethtool self-test")
Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Work request used for sending loopback packet needs to add
the firmware work request only once. So, fix by using
correct structure size.
Fixes: 7235ffae3d ("cxgb4: add loopback ethtool self-test")
Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If efx_nic_init_interrupt fails, or was never run (e.g. due to an earlier
failure in ef100_net_open), freeing irqs in efx_nic_fini_interrupt is not
needed and will cause error messages and stack traces.
So instead, only do this if efx_nic_init_interrupt successfully completed,
as indicated by the new efx->irqs_hooked flag.
Fixes: 965b549f3c ("sfc_ef100: implement ndo_open/close and EVQ probing")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an ef100_net_open() fails, ef100_net_stop() may be called without
channel->rps_flow_id having been written; thus it may hold the address
freed by a previous ef100_net_stop()'s call to efx_remove_filters().
This then causes a double-free when efx_remove_filters() is called
again, leading to a panic.
To prevent this, after freeing it, overwrite it with NULL.
Fixes: a9dc3d5612 ("sfc_ef100: RX filter table management and related gubbins")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When downing and upping the ef100 filter table, we need to take a write
lock on efx->filter_sem, not just a read lock, because we may kfree()
the table pointers.
Without this, resets cause a WARN_ON from efx_rwsem_assert_write_locked().
Fixes: a9dc3d5612 ("sfc_ef100: RX filter table management and related gubbins")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually hook up the .rx_buf_hash_valid method in EF100's nic_type.
Fixes: 068885434c ("sfc: check hash is valid before using it")
Reported-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remote source MAC addresses can be set on a 'source mode' macvlan
interface via the IFLA_MACVLAN_MACADDR_DATA attribute. This commit
tightens the validation of these MAC addresses to match the validation
already performed when setting or adding a single MAC address via the
IFLA_MACVLAN_MACADDR attribute.
iproute2 uses IFLA_MACVLAN_MACADDR_DATA for its 'macvlan macaddr set'
command, and IFLA_MACVLAN_MACADDR for its 'macvlan macaddr add' command,
which demonstrates the inconsistent behaviour that this commit
addresses:
# ip link add link eth0 name macvlan0 type macvlan mode source
# ip link set link dev macvlan0 type macvlan macaddr add 01:00:00:00:00:00
RTNETLINK answers: Cannot assign requested address
# ip link set link dev macvlan0 type macvlan macaddr set 01:00:00:00:00:00
# ip -d link show macvlan0
5: macvlan0@eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 ...
link/ether 2e:ac:fd:2d:69:f8 brd ff:ff:ff:ff:ff:ff promiscuity 0
macvlan mode source remotes (1) 01:00:00:00:00:00 numtxqueues 1 ...
With this change, the 'set' command will (rightly) fail in the same way
as the 'add' command.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_fcoe_ddp_setup() can be called from the main I/O path and is called
with a spin_lock held, so we have to use GFP_ATOMIC allocation instead of
GFP_KERNEL.
Link: https://lore.kernel.org/r/1596831813-9839-1-git-send-email-michael.christie@oracle.com
cc: Hannes Reinecke <hare@suse.de>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull networking fixes from David Miller:
"Another batch of fixes:
1) Remove nft_compat counter flush optimization, it generates warnings
from the refcount infrastructure. From Florian Westphal.
2) Fix BPF to search for build id more robustly, from Jiri Olsa.
3) Handle bogus getopt lengths in ebtables, from Florian Westphal.
4) Infoleak and other fixes to j1939 CAN driver, from Eric Dumazet and
Oleksij Rempel.
5) Reset iter properly on mptcp sendmsg() error, from Florian
Westphal.
6) Show a saner speed in bonding broadcast mode, from Jarod Wilson.
7) Various kerneldoc fixes in bonding and elsewhere, from Lee Jones.
8) Fix double unregister in bonding during namespace tear down, from
Cong Wang.
9) Disable RP filter during icmp_redirect selftest, from David Ahern"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (75 commits)
otx2_common: Use devm_kcalloc() in otx2_config_npa()
net: qrtr: fix usage of idr in port assignment to socket
selftests: disable rp_filter for icmp_redirect.sh
Revert "net: xdp: pull ethernet header off packet after computing skb->protocol"
phylink: <linux/phylink.h>: fix function prototype kernel-doc warning
mptcp: sendmsg: reset iter on error redux
net: devlink: Remove overzealous WARN_ON with snapshots
tipc: not enable tipc when ipv6 works as a module
tipc: fix uninit skb->data in tipc_nl_compat_dumpit()
net: Fix potential wrong skb->protocol in skb_vlan_untag()
net: xdp: pull ethernet header off packet after computing skb->protocol
ipvlan: fix device features
bonding: fix a potential double-unregister
can: j1939: add rxtimer for multipacket broadcast session
can: j1939: abort multipacket broadcast session when timeout occurs
can: j1939: cancel rxtimer on multipacket broadcast session complete
can: j1939: fix support for multipacket broadcast message
net: fddi: skfp: cfm: Remove seemingly unused variable 'ID_sccs'
net: fddi: skfp: cfm: Remove set but unused variable 'oldstate'
net: fddi: skfp: smt: Remove seemingly unused variable 'ID_sccs'
...
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kcalloc".
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing NETDEV_FEAT_CHANGE causes IPvlan links to lose
NETIF_F_LLTX feature because of the incorrect handling of
features in ipvlan_fix_features().
--before--
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: on [fixed]
lpaa10:~# ethtool -K ipvl0 tso off
Cannot change tcp-segmentation-offload
Actual changes:
vlan-challenged: off [fixed]
tx-lockless: off [fixed]
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: off [fixed]
lpaa10:~#
--after--
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: on [fixed]
lpaa10:~# ethtool -K ipvl0 tso off
Cannot change tcp-segmentation-offload
Could not change any device features
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: on [fixed]
lpaa10:~#
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we tear down a network namespace, we unregister all
the netdevices within it. So we may queue a slave device
and a bonding device together in the same unregister queue.
If the only slave device is non-ethernet, it would
automatically unregister the bonding device as well. Thus,
we may end up unregistering the bonding device twice.
Workaround this special case by checking reg_state.
Fixes: 9b5e383c11 ("net: Introduce unregister_netdevice_many()")
Reported-by: syzbot+af23e7f3e0a7e10c8b67@syzkaller.appspotmail.com
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is present in many source files and has not been used
anywhere (at least internally) since it was introduced.
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/cfm.c: In function ‘cfm’:
drivers/net/fddi/skfp/cfm.c:211:6: warning: variable ‘oldstate’ set but not used [-Wunused-but-set-variable]
drivers/net/fddi/skfp/cfm.c:40:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we're at it, remove some code which has never been invoked.
Keep the comment though, as it seems potentially half useful.
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/cfm.c: In function ‘cfm’:
drivers/net/fddi/skfp/cfm.c:211:6: warning: variable ‘oldstate’ set but not used [-Wunused-but-set-variable]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is present in many source files and has not been used
anywhere (at least internally) since it was introduced.
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/smt.c:24:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable 'smt_pdef' is only used if LITTLE_ENDIAN is set, so only
define it if this is the case.
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/smt.c:1572:3: warning: ‘smt_pdef’ defined but not used [-Wunused-const-variable=]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is present in many source files and has not been used
anywhere (at least internally) since it was introduced.
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/fplustm.c:25:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: netdev@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is present in many source files and has not been used
anywhere (at least internally) since it was introduced.
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/hwmtm.c:14:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/wan/dlci.c: In function ‘dlci_close’:
drivers/net/wan/dlci.c:298:8: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Mike McLagan <mike.mclagan@linux.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/8390/axnet_cs.c:907: warning: Function parameter or member 'txqueue' not described in 'axnet_tx_timeout'
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Martin Habets <mhabets@solarflare.com>
Cc: Shannon Nelson <snelson@pensando.io>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: William Lee <william@asix.com.tw>
Cc: "A. Hinds --" <dahinds@users.sourceforge.net>
Cc: reached at <becker@scyld.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/bonding/bond_alb.c:1222: warning: Function parameter or member 'bond' not described in 'alb_set_mac_address'
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/3com/3c574_cs.c: In function ‘update_stats’:
drivers/net/ethernet/3com/3c574_cs.c:954:9: warning: variable ‘tx’ set but not used [-Wunused-but-set-variable]
954 | u8 rx, tx, up;
| ^~
drivers/net/ethernet/3com/3c574_cs.c:954:5: warning: variable ‘rx’ set but not used [-Wunused-but-set-variable]
954 | u8 rx, tx, up;
| ^~
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Shannon Nelson <snelson@pensando.io>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Martin Habets <mhabets@solarflare.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Donald Becker <becker@scyld.com>
Cc: David Hinds <dahinds@users.sourceforge.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/bonding/bond_main.c:329: warning: Function parameter or member 'proto' not described in 'bond_vlan_rx_add_vid'
drivers/net/bonding/bond_main.c:362: warning: Function parameter or member 'proto' not described in 'bond_vlan_rx_kill_vid'
drivers/net/bonding/bond_main.c:964: warning: Function parameter or member 'new_active' not described in 'bond_change_active_slave'
drivers/net/bonding/bond_main.c:964: warning: Excess function parameter 'new' description in 'bond_change_active_slave'
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Thomas Davis <tadavis@lbl.gov>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renames and missing descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/net/bonding/bond_3ad.c:140: warning: Function parameter or member 'port' not described in '__get_first_agg'
drivers/net/bonding/bond_3ad.c:140: warning: Excess function parameter 'bond' description in '__get_first_agg'
drivers/net/bonding/bond_3ad.c:1655: warning: Function parameter or member 'agg' not described in 'ad_agg_selection_logic'
drivers/net/bonding/bond_3ad.c:1655: warning: Excess function parameter 'aggregator' description in 'ad_agg_selection_logic'
drivers/net/bonding/bond_3ad.c:1817: warning: Function parameter or member 'port' not described in 'ad_initialize_port'
drivers/net/bonding/bond_3ad.c:1817: warning: Excess function parameter 'aggregator' description in 'ad_initialize_port'
drivers/net/bonding/bond_3ad.c:1976: warning: Function parameter or member 'timeout' not described in 'bond_3ad_initiate_agg_selection'
drivers/net/bonding/bond_3ad.c:2274: warning: Function parameter or member 'work' not described in 'bond_3ad_state_machine_handler'
drivers/net/bonding/bond_3ad.c:2274: warning: Excess function parameter 'bond' description in 'bond_3ad_state_machine_handler'
drivers/net/bonding/bond_3ad.c:2508: warning: Function parameter or member 'link' not described in 'bond_3ad_handle_link_change'
drivers/net/bonding/bond_3ad.c:2508: warning: Excess function parameter 'status' description in 'bond_3ad_handle_link_change'
drivers/net/bonding/bond_3ad.c:2566: warning: Function parameter or member 'bond' not described in 'bond_3ad_set_carrier'
drivers/net/bonding/bond_3ad.c:2677: warning: Function parameter or member 'bond' not described in 'bond_3ad_update_lacp_rate'
drivers/net/bonding/bond_3ad.c:1655: warning: Function parameter or member 'agg' not described in 'ad_agg_selection_logic'
drivers/net/bonding/bond_3ad.c:1655: warning: Excess function parameter 'aggregator' description in 'ad_agg_selection_logic'
drivers/net/bonding/bond_3ad.c:1817: warning: Function parameter or member 'port' not described in 'ad_initialize_port'
drivers/net/bonding/bond_3ad.c:1817: warning: Excess function parameter 'aggregator' description in 'ad_initialize_port'
drivers/net/bonding/bond_3ad.c:1976: warning: Function parameter or member 'timeout' not described in 'bond_3ad_initiate_agg_selection'
drivers/net/bonding/bond_3ad.c:2274: warning: Function parameter or member 'work' not described in 'bond_3ad_state_machine_handler'
drivers/net/bonding/bond_3ad.c:2274: warning: Excess function parameter 'bond' description in 'bond_3ad_state_machine_handler'
drivers/net/bonding/bond_3ad.c:2508: warning: Function parameter or member 'link' not described in 'bond_3ad_handle_link_change'
drivers/net/bonding/bond_3ad.c:2508: warning: Excess function parameter 'status' description in 'bond_3ad_handle_link_change'
drivers/net/bonding/bond_3ad.c:2566: warning: Function parameter or member 'bond' not described in 'bond_3ad_set_carrier'
drivers/net/bonding/bond_3ad.c:2677: warning: Function parameter or member 'bond' not described in 'bond_3ad_update_lacp_rate'
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Added a skb->len check
This driver expects upper layers to include a pseudo header of 1 byte
when passing down a skb for transmission. This driver will read this
1-byte header. This patch added a skb->len check before reading the
header to make sure the header exists.
2. Added needed_headroom and set hard_header_len to 0
When this driver transmits data,
first this driver will remove a pseudo header of 1 byte,
then the lapb module will prepend the LAPB header of 2 or 3 bytes.
So the value of needed_headroom in this driver should be 3 - 1.
Because this driver has no header_ops, according to the logic of
af_packet.c, the value of hard_header_len should be 0.
Reason of setting needed_headroom and hard_header_len at this place:
This driver is written using the API of the hdlc module, the hdlc
module enables this driver (the protocol driver) to run on any hardware
that has a driver (the hardware driver) written using the API of the
hdlc module.
Two other hdlc protocol drivers - hdlc_ppp and hdlc_raw_eth, also set
things like hard_header_len at this place. In hdlc_ppp, it sets
hard_header_len after attach_hdlc_protocol and before setting dev->type.
In hdlc_raw_eth, it sets hard_header_len by calling ether_setup after
attach_hdlc_protocol and after memcpy the settings.
3. Reset needed_headroom when detaching protocols (in hdlc.c)
When detaching a protocol from a hardware device, the hdlc module will
reset various parameters of the device (including hard_header_len) to
the default values. We add needed_headroom here so that needed_headroom
will also be reset.
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcast mode bonds transmit a copy of all traffic simultaneously out of
all interfaces, so the "speed" of the bond isn't really the aggregate of
all interfaces, but rather, the speed of the slowest active interface.
Also, the type of the speed field is u32, not unsigned long, so adjust
that accordingly, as required to make min() function here without
complaining about mismatching types.
Fixes: bb5b052f75 ("bond: add support to read speed and duplex via ethtool")
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ioreadX() helpers have inconsistent interface. On some architectures
void *__iomem address argument is a pointer to const, on some not.
Implementations of ioreadX() do not modify the memory under the address so
they can be converted to a "const" version for const-safety and
consistency among architectures.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Allen Hubbe <allenbh@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200709072837.5869-3-krzk@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct the error path for regulator disable.
Fixes: 9269e5560b ("net: fec: add phy-reset-gpios PROBE_DEFER check")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-08-14
This series contains updates to i40e and igc drivers.
Vinicius fixes an issue with PTP spinlock being accessed before
initialization.
Przemyslaw fixes an issue with trusted VFs seeing additional traffic.
Grzegorz adds a wait for pending resets on driver removal to prevent
null pointer dereference.
v2: Fix function parameter for hw/aq in patch 2. Fix fixes tag in patch 3.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trusted VF with unicast promiscuous mode set, could listen to TX
traffic of other VFs.
Set unicast promiscuous mode to RX traffic, if VSI has port VLAN
configured. Rename misleading I40E_AQC_SET_VSI_PROMISC_TX bit to
I40E_AQC_SET_VSI_PROMISC_RX_ONLY. Aligned unicast promiscuous with
VLAN to the one without VLAN.
Fixes: 6c41a76069 ("i40e: Add promiscuous on VLAN support")
Fixes: 3b1200891b ("i40e: When in promisc mode apply promisc mode to Tx Traffic as well")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
On EF100, the RX hash field in the packet prefix may not be valid (e.g.
if the header parse failed), and this is indicated by a one-bit flag
elsewhere in the packet prefix. Only call skb_set_hash() if the
RSS_HASH_VALID bit is set.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuusuke Ashizuka