Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calling force_performance_level() from set_power_state()
doesn't work on some asics because the current power
state pointer has not been properly updated at that point.
Move the calls to force_performance_level() out of the
asic specific set_power_state() functions and into
the main power state sequence.
Fixes dpm resume on SI.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check to make sure the dc limits are valid before using them.
Some systems may not have a dc limits table. In that case just
use the ac limits. This fixes hangs on systems when the power
state is changed when on battery (dc) due to invalid performance
state parameters.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=68708
v2: fix up limits in dpm_init()
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Clockgating needs to be disabled around certain parts
of dpm setup otherwise the smc gets into a bad state
and dpm doesn't work properly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for btc asics. This includes:
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen switching
Set radeon.dpm=1 to enable.
v2: remove unused radeon_atombios.c changes,
make missing smc ucode non-fatal
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are some hardware issue with reclocking on SI when
UVD is active, so use a stable power state when UVD is
active. Fixes possible hangs and performance issues when
using UVD on SI.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to check for engine and memory clock ss separately
and only enable dynamic ss if either of them are found.
This should fix systems which have a ss table, but do
not have entries for engine or memory. On those systems
we may enable dynamic spread spectrum without enabling
it on the engine or memory clocks which can lead to a
hang in some cases.
fixes some systems reported here:
https://bugs.freedesktop.org/show_bug.cgi?id=66963
v2: fix typo
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On rv770 and newer, clock gating is not required
for thermal protection. The only requirement is that
the design utilizes a thermal sensor.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The SMC interface changed compared to Cayman and
previous asics. Set the enabled levels properly
and enable reclocking by default when dpm is enabled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable cac setup on SI for now since it causes
strange performance level restrictions on certain
cards. I suspect there may be issues with some of
the 64 bit fixed point double emulation that is used
to set up those parameters. I need to double check
the math before this can be re-enabled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to set the DISP*_GAP fields as well as the
DISP*_GAP_MCHG fields. Same as on previous asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if we can switch the mclk during the vblank time otherwise
we may get artifacts on the screen when the mclk changes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for SI asics. This includes:
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2/gen3 switching
- power containment
- shader power scaling
Set radeon.dpm=1 to enable.
v2: enable hainan support, rebase
v3: guard acpi stuff
v4: fix 64 bit math
v5: fix 64 bit div harder
v6: fix thermal interrupt check noticed by Jerome
v7: attempt fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher