This is to prevent the case of working with a single MPWQE
(1 WQE is always reserved as RQ is linked-list).
When the WQE is fully consumed, HW should still have available buffer
in order not to drop packets.
Fixes: 461017cb00 ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, when dma mapping fails, put_page is called,
but the page is not set to null. Later, in the page_reuse treatment in
mlx5e_free_rx_descs(), mlx5e_page_release() is called for the second time,
improperly doing dma_unmap (for a non-mapped address) and an extra put_page.
Prevent this by nullifying the page pointer when dma_map fails.
Fixes: accd588332 ("net/mlx5e: Introduce RX Page-Reuse")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
napi->poll can be called with budget 0, e.g. in netpoll scenarios
where the caller only wants to poll TX rings
(poll_one_napi@net/core/netpoll.c).
The below commit changed RX polling from "while" loop to "do {} while",
which caused to ignore the initial budget and handle at least one RX
packet.
This fixes the following warning:
[ 2852.049194] mlx5e_napi_poll+0x0/0x260 [mlx5_core] exceeded budget in poll
[ 2852.049195] ------------[ cut here ]------------
[ 2852.049195] WARNING: CPU: 0 PID: 25691 at net/core/netpoll.c:171 netpoll_poll_dev+0x18a/0x1a0
Fixes: 4b7dfc9925 ("net/mlx5e: Early-return on empty completion queues")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Martin KaFai Lau <kafai@fb.com>
Tested-by: Martin KaFai Lau <kafai@fb.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After the panic teardown firmware command, health_care detects the error
in PCI bus and calls the mlx5_pci_err_detected. This health_care flow is
no longer needed because the panic teardown firmware command will bring
down the PCI bus communication with the HCA.
The solution is to cancel the health care timer and its pending
workqueue request before sending panic teardown firmware command.
Kernel trace:
mlx5_core 0033:01:00.0: Shutdown was called
mlx5_core 0033:01:00.0: health_care:154:(pid 9304): handling bad device here
mlx5_core 0033:01:00.0: mlx5_handle_bad_state:114:(pid 9304): NIC state 1
mlx5_core 0033:01:00.0: mlx5_pci_err_detected was called
mlx5_core 0033:01:00.0: mlx5_enter_error_state:96:(pid 9304): start
mlx5_3:mlx5_ib_event:3061:(pid 9304): warning: event on port 0
mlx5_core 0033:01:00.0: mlx5_enter_error_state:104:(pid 9304): end
Unable to handle kernel paging request for data at address 0x0000003f
Faulting instruction address: 0xc0080000434b8c80
Fixes: 8812c24d28 ('net/mlx5: Add fast unload support in shutdown flow')
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
list_splice_init initializing waiting_events_list after splicing it to
temp list, therefore we should loop over temp list to fire the events.
Fixes: 4ca637a20a ("net/mlx5: Delay events till mlx5 interface's add complete for pci resume")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
- Prevent the schedutil cpufreq governor from using the
utilization of a wrong CPU in some cases which started to
happen after one of the recent changes in it (Chris Redpath).
- Blacklist Dell XPS13 9360 from using the Low Power S0 Idle _DSM
interface as that causes serious issue (related to NVMe) to
appear on one of these machines, even though the other Dells
XPS13 9360 in somewhat different HW configurations behave
correctly (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJaBFMsAAoJEILEb/54YlRxb8sP/jhqgCEiaUvSpFYBLklx1fqK
QDbbYw3Os2JlAcMFElGjZEoV0+WBbadTHQxIxB353mpcAe1moI/SoDAJEgA9HWib
tjJIt1lak3nLF967y0pOgAi9uvFCG6Rw+ZyVSrYBnT+eG6fw3h6MdHaOEFeCHJY4
qUgj+Bm0OtisW9mRFk5zdGam+6MxaE1z9mhjRAebrAjOI+46Oj/LQl7q32S2vWTp
GJm6lSYOmSruo5vdU7T3dOSkBrkymf4E//1XkegFvcweEX/aITuCAil0Rl4X2PV0
NSeeCp66skftvlZ/vf3QOem1XLgPdVZ9dr7WRzOZt3CDctXuDaA3uKfRJf3oIMsi
rnrsmWnfsT4sNaqV6zHYTkMtQfSsxFfjOde/HC7vAtC0oM/EECsonBtIlMUBmYlR
7fi+wtrE6ErsMgkThOvplG+cAnvWCK8yhmFBAKbcwg9UHwooF0HxXPqVwHE6M8pw
eFALkJyagx1PTGKXNHOUTHfZcYGlhhJxH6SEhs/pJIxL8rVgey8mJfA9y8eGmEXP
fKPnEb6yI7/9ZpzFFu3DLiHMifgc6o9F0mRqw3apeQFGtg46frYw51meP5Faq0EZ
BAb0AXBF4qNB+XvORG0ABJkPqqDaZVPVfdo1SIA06IBr2mpVT1RAetMU0qSuWy+x
STI04myU/9hHmCSdqzpg
=F9fg
-----END PGP SIGNATURE-----
Merge tag 'pm-final-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull final power management fixes from Rafael Wysocki:
"These fix a regression in the schedutil cpufreq governor introduced by
a recent change and blacklist Dell XPS13 9360 from using the Low Power
S0 Idle _DSM interface which triggers serious problems on one of these
machines.
Specifics:
- Prevent the schedutil cpufreq governor from using the utilization
of a wrong CPU in some cases which started to happen after one of
the recent changes in it (Chris Redpath).
- Blacklist Dell XPS13 9360 from using the Low Power S0 Idle _DSM
interface as that causes serious issue (related to NVMe) to appear
on one of these machines, even though the other Dells XPS13 9360 in
somewhat different HW configurations behave correctly (Rafael
Wysocki)"
* tag 'pm-final-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Blacklist Low Power S0 Idle _DSM for Dell XPS13 9360
cpufreq: schedutil: Examine the correct CPU when we update util
The amount of the changes isn't as quite small as wished, nevertheless
they are straight fixes that deserve merging to 4.14 final.
Most of fixes are about ALSA core bugs spotted by fuzzer: a follow-up
fix for the previous nested rwsem patch, a fix to avoid the resource
hogs due to too many concurrent ALSA timer invocations, and a fix for
a crash with SYSEX MIDI transfer over OSS sequencer emulation that is
used by none but fuzzer.
The rest are usual HD-audio and USB-audio device-specific quirks,
which are safe to apply.
-----BEGIN PGP SIGNATURE-----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=Q2mh
-----END PGP SIGNATURE-----
Merge tag 'sound-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The amount of the changes isn't as quite small as wished, nevertheless
they are straight fixes that deserve merging to 4.14 final.
Most of fixes are about ALSA core bugs spotted by fuzzer: a follow-up
fix for the previous nested rwsem patch, a fix to avoid the resource
hogs due to too many concurrent ALSA timer invocations, and a fix for
a crash with SYSEX MIDI transfer over OSS sequencer emulation that is
used by none but fuzzer.
The rest are usual HD-audio and USB-audio device-specific quirks,
which are safe to apply"
* tag 'sound-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - fix headset mic problem for Dell machines with alc274
ALSA: seq: Fix OSS sysex delivery in OSS emulation
ALSA: seq: Avoid invalid lockdep class warning
ALSA: timer: Limit max instances per timer
ALSA: usb-audio: support new Amanero Combo384 firmware version
Pull networking fixes from David Miller:
1) Fix use-after-free in IPSEC input parsing, desintation address
pointer was loaded before pskb_may_pull() which can change the SKB
data pointers. From Florian Westphal.
2) Stack out-of-bounds read in xfrm_state_find(), from Steffen
Klassert.
3) IPVS state of SKB is not properly reset when moving between
namespaces, from Ye Yin.
4) Fix crash in asix driver suspend and resume, from Andrey Konovalov.
5) Don't deliver ipv6 l2tp tunnel packets to ipv4 l2tp tunnels, and
vice versa, from Guillaume Nault.
6) Fix DSACK undo on non-dup ACKs, from Priyaranjan Jha.
7) Fix regression in bond_xmit_hash()'s behavior after the TCP port
selection changes back in 4.2, from Hangbin Liu.
8) Two divide by zero bugs in USB networking drivers when parsing
descriptors, from Bjorn Mork.
9) Fix bonding slaves being stuck in BOND_LINK_FAIL state, from Jay
Vosburgh.
10) Missing skb_reset_mac_header() in qmi_wwan, from Kristian Evensen.
11) Fix the destruction of tc action object races properly, from Cong
Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (31 commits)
cls_u32: use tcf_exts_get_net() before call_rcu()
cls_tcindex: use tcf_exts_get_net() before call_rcu()
cls_rsvp: use tcf_exts_get_net() before call_rcu()
cls_route: use tcf_exts_get_net() before call_rcu()
cls_matchall: use tcf_exts_get_net() before call_rcu()
cls_fw: use tcf_exts_get_net() before call_rcu()
cls_flower: use tcf_exts_get_net() before call_rcu()
cls_flow: use tcf_exts_get_net() before call_rcu()
cls_cgroup: use tcf_exts_get_net() before call_rcu()
cls_bpf: use tcf_exts_get_net() before call_rcu()
cls_basic: use tcf_exts_get_net() before call_rcu()
net_sched: introduce tcf_exts_get_net() and tcf_exts_put_net()
Revert "net_sched: hold netns refcnt for each action"
net: usb: asix: fill null-ptr-deref in asix_suspend
Revert "net: usb: asix: fill null-ptr-deref in asix_suspend"
qmi_wwan: Add missing skb_reset_mac_header-call
bonding: fix slave stuck in BOND_LINK_FAIL state
qrtr: Move to postcore_initcall
net: qmi_wwan: fix divide by 0 on bad descriptors
net: cdc_ether: fix divide by 0 on bad descriptors
...
Confirmed with Kailang of Realtek, the pin 0x19 is for Headset Mic, and
the pin 0x1a is for Headphone Mic, he suggested to apply
ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to fix this problem. And we
verified applying this FIXUP can fix this problem.
Cc: <stable@vger.kernel.org>
Cc: Kailang Yang <kailang@realtek.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Steffen Klassert says:
====================
pull request (net): ipsec 2017-11-09
1) Fix a use after free due to a reallocated skb head.
From Florian Westphal.
2) Fix sporadic lookup failures on labeled IPSEC.
From Florian Westphal.
3) Fix a stack out of bounds when a socket policy is applied
to an IPv6 socket that sends IPv4 packets.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang says:
====================
net_sched: close the race between call_rcu() and cleanup_net()
This patchset tries to fix the race between call_rcu() and
cleanup_net() again. Without holding the netns refcnt the
tc_action_net_exit() in netns workqueue could be called before
filter destroy works in tc filter workqueue. This patchset
moves the netns refcnt from tc actions to tcf_exts, without
breaking per-netns tc actions.
Patch 1 reverts the previous fix, patch 2 introduces two new
API's to help to address the bug and the rest patches switch
to the new API's. Please see each patch for details.
I was not able to reproduce this bug, but now after adding
some delay in filter destroy work I manage to trigger the
crash. After this patchset, the crash is not reproducible
any more and the debugging printk's show the order is expected
too.
====================
Fixes: ddf97ccdd7 ("net_sched: add network namespace support for tc actions")
Reported-by: Lucas Bates <lucasb@mojatatu.com>
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of holding netns refcnt in tc actions, we can minimize
the holding time by saving it in struct tcf_exts instead. This
means we can just hold netns refcnt right before call_rcu() and
release it after tcf_exts_destroy() is done.
However, because on netns cleanup path we call tcf_proto_destroy()
too, obviously we can not hold netns for a zero refcnt, in this
case we have to do cleanup synchronously. It is fine for RCU too,
the caller cleanup_net() already waits for a grace period.
For other cases, refcnt is non-zero and we can safely grab it as
normal and release it after we are done.
This patch provides two new API for each filter to use:
tcf_exts_get_net() and tcf_exts_put_net(). And all filters now can
use the following pattern:
void __destroy_filter() {
tcf_exts_destroy();
tcf_exts_put_net(); // <== release netns refcnt
kfree();
}
void some_work() {
rtnl_lock();
__destroy_filter();
rtnl_unlock();
}
void some_rcu_callback() {
tcf_queue_work(some_work);
}
if (tcf_exts_get_net()) // <== hold netns refcnt
call_rcu(some_rcu_callback);
else
__destroy_filter();
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ceffcc5e25.
If we hold that refcnt, the netns can never be destroyed until
all actions are destroyed by user, this breaks our netns design
which we expect all actions are destroyed when we destroy the
whole netns.
Cc: Lucas Bates <lucasb@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit baedf68a06.
There is an updated version of this fix which covers
the problem more thoroughly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7744ccdbc1 ("x86/mm: Add Secure Memory Encryption (SME)
support") as a side-effect made PAGE_KERNEL all of a sudden unavailable
to modules which can't make use of EXPORT_SYMBOL_GPL() symbols.
This is because once SME is enabled, sme_me_mask (which is introduced as
EXPORT_SYMBOL_GPL) makes its way to PAGE_KERNEL through _PAGE_ENC,
causing imminent build failure for all the modules which make use of all
the EXPORT-SYMBOL()-exported API (such as vmap(), __vmalloc(),
remap_pfn_range(), ...).
Exporting (as EXPORT_SYMBOL()) interfaces (and having done so for ages)
that take pgprot_t argument, while making it impossible to -- all of a
sudden -- pass PAGE_KERNEL to it, feels rather incosistent.
Restore the original behavior and make it possible to pass PAGE_KERNEL
to all its EXPORT_SYMBOL() consumers.
[ This is all so not wonderful. We shouldn't need that "sme_me_mask"
access at all in all those places that really don't care about that
level of detail, and just want _PAGE_KERNEL or whatever.
We have some similar issues with _PAGE_CACHE_WP and _PAGE_NOCACHE,
both of which hide a "cachemode2protval()" call, and which also ends
up using another EXPORT_SYMBOL(), but at least that only triggers for
the much more rare cases.
Maybe we could move these dynamic page table bits to be generated much
deeper down in the VM layer, instead of hiding them in the macros that
everybody uses.
So this all would merit some cleanup. But not today. - Linus ]
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Despised-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull key handling fix from James Morris:
"Fix by Eric Biggers for the keys subsystem"
* 'fixes-v4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: fix NULL pointer dereference during ASN.1 parsing [ver #2]
This came in yesterday, and I have verified our regression tests
were missing this and it can cause an oops. Please apply.
There is a an off-by-one comparision on sig against MAXMAPPED_SIG
that can lead to a read outside the sig_map array if sig
is MAXMAPPED_SIG. Fix this.
Verified that the check is an out of bounds case that can cause an oops.
Revised: add comparison fix to second case
Fixes: cd1dbf76b2 ("apparmor: add the ability to mediate signals")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bonding miimon logic has a flaw, in that a failure of the
rtnl_trylock can cause a slave to become permanently stuck in
BOND_LINK_FAIL state.
The sequence of events to cause this is as follows:
1) bond_miimon_inspect finds that a slave's link is down, and so
calls bond_propose_link_state, setting slave->new_link_state to
BOND_LINK_FAIL, then sets slave->new_link to BOND_LINK_DOWN and returns
non-zero.
2) In bond_mii_monitor, the rtnl_trylock fails, and the timer is
rescheduled. No change is committed.
3) bond_miimon_inspect is called again, but this time the slave
from step 1 has recovered. slave->new_link is reset to NOCHANGE, and, as
slave->link was never changed, the switch enters the BOND_LINK_UP case,
and does nothing. The pending BOND_LINK_FAIL state from step 1 remains
pending, as new_link_state is not reset.
4) The state from step 3 persists until another slave changes link
state and causes bond_miimon_inspect to return non-zero. At this point,
the BOND_LINK_FAIL state change on the slave from steps 1-3 is committed,
and the slave will remain stuck in BOND_LINK_FAIL state even though it
is actually link up.
The remedy for this is to initialize new_link_state on each entry
to bond_miimon_inspect, as is already done with new_link.
Fixes: fb9eb899a6 ("bonding: handle link transition from FAIL to UP correctly")
Reported-by: Alex Sidorenko <alexandre.sidorenko@hpe.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registering qrtr with module_init makes the ability of typical platform
code to create AF_QIPCRTR socket during probe a matter of link order
luck. Moving qrtr to postcore_initcall() avoids this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting dev->hard_mtu to 0 will cause a divide error in
usbnet_probe. Protect against devices with bogus CDC Ethernet
functional descriptors by ignoring a zero wMaxSegmentSize.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 07f4c90062 ("tcp/dccp: try to not exhaust ip_local_port_range
in connect()"), we will try to use even ports for connect(). Then if an
application (seen clearly with iperf) opens multiple streams to the same
destination IP and port, each stream will be given an even source port.
So the bonding driver's simple xmit_hash_policy based on layer3+4 addressing
will always hash all these streams to the same interface. And the total
throughput will limited to a single slave.
Change the tcp code will impact the whole tcp behavior, only for bonding
usage. Paolo Abeni suggested fix this by changing the bonding code only,
which should be more reasonable, and less impact.
Fix this by discarding the lowest hash bit because it contains little entropy.
After the fix we can re-balance between slaves.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hn is being kfree'd in mlx5e_del_l2_from_hash and then dereferenced
by accessing hn->ai.addr
Fix this by copying the MAC address into a local variable for its safe use
in all possible execution paths within function mlx5e_execute_l2_action.
Addresses-Coverity-ID: 1417789
Fixes: eeb66cdb68 ("net/mlx5: Separate between E-Switch and MPFS")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2 driver can't cope at all with the TX affinities being
changed from userspace, and spit an endless stream of
[ 91.779920] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.779930] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780402] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780406] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780415] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780418] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
rendering the box completely useless (I've measured around 600k
interrupts/s on a 8040 box) once irqbalance kicks in and start
doing its job.
Obviously, the driver was never designed with this in mind. So let's
work around the problem by preventing userspace from interacting
with these interrupts altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 0day bot reports the below failure which happens occasionally, with
their randconfig testing (once every ~100 boots). The Code points at
the private pointer ->driver_data being NULL, which hints at a race of
sorts where the private driver_data descriptor has disappeared by the
time we get to run the workqueue.
So let's check that pointer before we continue with issuing the command
to the drive.
This fix is of the brown paper bag nature but considering that IDE is
long deprecated, let's do that so that random testing which happens to
enable CONFIG_IDE during randconfig builds, doesn't fail because of
this.
Besides, failing the TEST_UNIT_READY command because the drive private
data is gone is something which we could simply do anyway, to denote
that there was a problem communicating with the device.
BUG: unable to handle kernel NULL pointer dereference at 000001c0
IP: cdrom_check_status
*pde = 00000000
Oops: 0000 [#1] SMP
CPU: 1 PID: 155 Comm: kworker/1:2 Not tainted 4.14.0-rc8 #127
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Workqueue: events_freezable_power_ disk_events_workfn
task: 4fe90980 task.stack: 507ac000
EIP: cdrom_check_status+0x2c/0x90
EFLAGS: 00210246 CPU: 1
EAX: 00000000 EBX: 4fefec00 ECX: 00000000 EDX: 00000000
ESI: 00000003 EDI: ffffffff EBP: 467a9340 ESP: 507aded0
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 80050033 CR2: 000001c0 CR3: 06e0f000 CR4: 00000690
Call Trace:
? ide_cdrom_check_events_real
? cdrom_check_events
? disk_check_events
? process_one_work
? process_one_work
? worker_thread
? kthread
? process_one_work
? __kthread_create_on_node
? ret_from_fork
Code: 53 83 ec 14 89 c3 89 d1 be 03 00 00 00 65 a1 14 00 00 00 89 44 24 10 31 c0 8b 43 18 c7 44 24 04 00 00 00 00 c7 04 24 00 00 00 00 <8a> 80 c0 01 00 00 c7 44 24 08 00 00 00 00 83 e0 03 c7 44 24 0c
EIP: cdrom_check_status+0x2c/0x90 SS:ESP: 0068:507aded0
CR2: 00000000000001c0
---[ end trace 2410e586dd8f88b2 ]---
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 8a97712e53.
This commit added a call to sysfs_notify() from within
scsi_device_set_state(), which in turn turns out to make libata very
unhappy, because ata_eh_detach_dev() does
spin_lock_irqsave(ap->lock, flags);
..
if (ata_scsi_offline_dev(dev)) {
dev->flags |= ATA_DFLAG_DETACHED;
ap->pflags |= ATA_PFLAG_SCSI_HOTPLUG;
}
and ata_scsi_offline_dev() then does that scsi_device_set_state() to set
it offline.
So now we called sysfs_notify() from within a spinlocked region, which
really doesn't work. The 0day robot reported this as:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:238
because sysfs_notify() ends up calling kernfs_find_and_get_ns() which
then does mutex_lock(&kernfs_mutex)..
The pollability of the device state isn't critical, so revert this all
for now, and maybe we'll do it differently in the future.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SYSEX event delivery in OSS sequencer emulation assumed that the
event is encoded in the variable-length data with the straight
buffering. This was the normal behavior in the past, but during the
development, the chained buffers were introduced for carrying more
data, while the OSS code was left intact. As a result, when a SYSEX
event with the chained buffer data is passed to OSS sequencer port,
it may end up with the wrong memory access, as if it were having a too
large buffer.
This patch addresses the bug, by applying the buffer data expansion by
the generic snd_seq_dump_var_event() helper function.
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Mark Salyzyn <salyzyn@android.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At least one Dell XPS13 9360 is reported to have serious issues with
the Low Power S0 Idle _DSM interface and since this machine model
generally can do ACPI S3 just fine, add a blacklist entry to disable
that interface for Dell XPS13 9360.
Fixes: 8110dd281e (ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196907
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 4.13+ <stable@vger.kernel.org> # 4.13+
Pull workqueue fix from Tejun Heo:
"Another fix for a really old bug.
It only affects drain_workqueue() which isn't used often and even then
triggers only during a pretty small race window, so it isn't too
surprising that it stayed hidden for so long.
The fix is straight-forward and low-risk. Kudos to Li Bin for
reporting and fixing the bug"
* 'for-4.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Fix NULL pointer dereference
Currently we are leaking addresses from the kernel to user space. This
script is an attempt to find some of those leakages. Script parses
`dmesg` output and /proc and /sys files for hex strings that look like
kernel addresses.
Only works for 64 bit kernels, the reason being that kernel addresses on
64 bit kernels have 'ffff' as the leading bit pattern making greping
possible. On 32 kernels we don't have this luxury.
Scripts is _slightly_ smarter than a straight grep, we check for false
positives (all 0's or all 1's, and vsyscall start/finish addresses).
[ I think there is a lot of room for improvement here, but it's already
useful, so I'm merging it as-is. The whole "hash %p format" series is
expected to go into 4.15, but will not fix %x users, and will not
incentivize people to look at what they are leaking. - Linus ]
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent fix for adding rwsem nesting annotation was using the given
"hop" argument as the lock subclass key. Although the idea itself
works, it may trigger a kernel warning like:
BUG: looking up invalid subclass: 8
....
since the lockdep has a smaller number of subclasses (8) than we
currently allow for the hops there (10).
The current definition is merely a sanity check for avoiding the too
deep delivery paths, and the 8 hops are already enough. So, as a
quick fix, just follow the max hops as same as the max lockdep
subclasses.
Fixes: 1f20f9ff57 ("ALSA: seq: Fix nested rwsem annotation for lockdep splat")
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull crypto fixes from Herbert Xu:
"This fixes an unaligned panic in x86/sha-mb and a bug in ccm that
triggers with certain underlying implementations"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ccm - preserve the IV buffer
crypto: x86/sha1-mb - fix panic due to unaligned access
crypto: x86/sha256-mb - fix panic due to unaligned access
Currently we allow unlimited number of timer instances, and it may
bring the system hogging way too much CPU when too many timer
instances are opened and processed concurrently. This may end up with
a soft-lockup report as triggered by syzkaller, especially when
hrtimer backend is deployed.
Since such insane number of instances aren't demanded by the normal
use case of ALSA sequencer and it merely opens a risk only for abuse,
this patch introduces the upper limit for the number of instances per
timer backend. As default, it's set to 1000, but for the fine-grained
timer like hrtimer, it's set to 100.
Reported-by: syzbot
Tested-by: Jérôme Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Eugenia Emantayev