During hw initialisation, wifi may be ready after bt has already been
ready, which causes bt to act abnormally. To avoid this, set GNT_BT to
high during hw init.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Stable <stable@vger.kernel.org>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some chips use an external antenna switch, but fw may not realize it.
Here we tell fw exactly that which type of switch we are using.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For a2dp and hid, we need extra process to avoid voice degradation
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If bt is queing, we need to set the packet priority properly.
Originally we only consider if wifi was connected or not, but now we
also consider if bt is under abnormal scan or wifi is scanning, roaming
or linking, and set the coex table.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver is going to sleep, it does not leave LPS/IPS, thus the
BTCoex may have mismatch when driver wakes up. To avoid that, BTCoex
needs to clear the IPS/LPS state when it receives a pnp notify, then
it can properly set up the hw when driver wakes up.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the hardware initialisation stage, the PTA circuits may be unstable,
so we reset it after 6 secs to fix the problem.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These cases are for the btcoex to tune the performance
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If ap num < 10, let wifi and bt transmit simultaneously, otherwise set
wifi into standy when bt is transmitting
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable is for PS tdma duration adjust, so rename it to clearly
to specify its usage.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For time division multiple access, the wifi and bt take turns to
transmit, but we need to let AP know that wifi is under standby mode by
sending null data to "pretend" entering power saving state using lps
rpwm.
But, the fw does not know if it is the actual power saving mode or just a
fake one to cheat to the AP. Hence, before fw setting the tdma duration,
the fw needs the driver to check the power saving state first.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When receiving pno results there may be duplicate channels and/or
ssids. Assure each is added only once when preparing the internal
escan request.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checking whether the address of an array element is null is bogus
so removing it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Assure the event data buffer is long enough to hold the array
of netinfo items and that SSID length does not exceed the maximum
of 32 characters as per 802.11 spec.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The fwsignal module is part of the bcdc protocol and as such does
its instance data is not needed in core structure. Moving it into
struct brcmf_bcdc instead.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When brcmf_fws_add_interface() is called the struct brcmf_if::fws_desc
field is initialized regardless the state of the fwsignal functionality,
ie. the fcmode. This is not needed when fcmode is NONE, which is the
default mode.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a non-functional change to align the fwsignal module to
the naming pattern used throughout the driver.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Systems with 64 bit DMA at least partially require buffers to be used
for DMA to be 8-byte-aligned. One example is Amlogic Meson GX.
Switching the MMC/SDIO driver for this platform to SG DMA mode
resulted in problems due to unaligned buffers.
Fortunately the brcmfmac driver has a global define for the alignment.
Changing it to 8 fixed the issues with Meson GX.
Suggested-by: Helmut Klein <hgkr.klein@gmail.com>
Tested-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have to use start port, for TX/RX of single packet,
instead of current aggregating port. This will fix SDIO
CMD53(TX/RX) returning -ETIMEDOUT and halting the data path.
Fixes: 0cb52aac4d ("mwifiex: do not set multiport flag for tx/rx single packet")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This field is never big enough to warrant 16-bitness.
8-bit accesses enjoy shorted encoding on i386/x86_64 than 16-bit
accesses:
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-10 (-10)
function old new delta
loopback_setup 169 164 -5
ether_setup 148 143 -5
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver may use build_skb() for received packets.
These SKBs then have a head_frag.
Since commit d7e8883cfc ("net: make GRO aware of
skb->head_frag"), GRO may build frag_list SKBs out of
head_frag received SKBs.
In such a case, the chained SKBs end up with a head_frag.
Commit 07b26c9454 ("gso: Support partial splitting at
the frag_list pointer") adds partial segmentation of frag_list
SKB chains into individual SKBs.
However, this is not done if the chained SKBs have any
linear part, because the device may not be able to DMA
the private linear buffer.
A chained frag_list SKB with head_frag is wrongfully
detected in this case as having a private linear part
and thus falls back to software GSO, while in fact the
linear part is backed by a DMA page just like any other frag.
This causes low performance when forwarding those packets
that were built with build_skb()
Allow partial segmentation at the frag_list pointer for
chained SKBs with head_frag.
Note that such SKBs can only be created by GRO, when applied
to received packets with head_frag.
Also note that this change only affects the data path that
performs the partial segmentation at frag_list pointer, and
not any of the other more common data paths.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault says:
====================
l2tp: constify l2tp_session_get*() and l2tp_tunnel_find*()
Declare parameters of these functions as "const" where possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_tunnel_find() and l2tp_tunnel_find_nth() don't modify "net".
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make l2tp_pernet()'s parameter constant, so that l2tp_session_get*() can
declare their "net" variable as "const".
Also constify "ifname" in l2tp_session_get_by_ifname().
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt says:
====================
ftgmac100: Rework batch 4 - Misc
This is v2 of the fourth batch of updates to the ftgmac100 driver.
This is a bunch of misc cleanups and fixes, such as properly
disabling HW checksum generation on AST2400 where it's known
to be broken and some chip init updates.
This also adds the ability to turn HW checksum on/off and
configure the ring sizes via ethtool.
v2 Fixes patch 1/10 (NETIF_F_HW_CSUM conversion)
The next (and last) batch will add a few more "features" such
as netpoll, multicast/promist, vlan offload...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I haven't seen any improvement above that size on the machines
I've tested with.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set an arbitrary max at 1024 since we pre-allocate the actual
descriptor arrays and skb arrays to the full size to keep the
code a bit simpler and avoid allocation failures in the reset
task.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear stale interrupts on entry, configure FIFO sizes, set FIFO
thresholds, configure interrupt mitigation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helpers just take space but don't provide much value. Simple
one line comments are more explanatory.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To remove more confusion. This function is about obtaining the
initial MAC address at driver probe time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid confusion with the ndo callback and generally be
clearer about the purpose of that function
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
So features can be turned on/off via ethtool
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found out that HW checksum generation only works from AST2500
onward. This disables it on AST2400 and removes the "no-hw-checksum"
properties in the device-trees. The problem we had wasn't related
to NC-SI.
Also rework the logic testing for that property so it can be used
to disable HW checksum generation and checking regardless of whether
NC-SI is used or not in case other variants out there need this.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We test for aspeed chips to handle a couple of special cases,
but we do that by checking the machine type which isn't right.
Instead check the actual device compatible property. This also
updates the dtsi files for the aspeed SoC to match.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation describes NETIF_F_IP_CSUM as deprecated
so let's switch to NETIF_F_HW_CSUM and use the helper to
handle unhandled protocols.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
net/smc: patches for net-next
here are some patches for net/smc. Most important are
improvements for socket closing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
smc specifies IB_SEND_INLINE for IB_WR_SEND ib_post_send calls, but
provides a mapped buffer to be sent. This is inconsistent, since
IB_SEND_INLINE works without mapped buffer. Problem has not been
detected in the past, because tests had been limited to Connect X3 cards
from Mellanox, whose mlx4 driver just ignored the IB_SEND_INLINE flag.
For now, the IB_SEND_INLINE flag is removed.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure sockets never accepted are removed cleanly.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
unhash is already called in sock_put_work. Remove the second call.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State SMC_CLOSED should be reached only, if ConnClosed has been sent to
the peer. If ConnClosed is received from the peer, a socket with
shutdown SHUT_WR done, switches errorneously to state SMC_CLOSED, which
means the peer socket is dangling. The local SMC socket is supposed to
switch to state APPFINCLOSEWAIT to make sure smc_close_final() is called
during socket close.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several state changes occur during SMC socket closing. Currently
state changes triggered locally occur in process context with
lock_sock() taken while state changes triggered by peer occur in
tasklet context with bh_lock_sock() taken. bh_lock_sock() does not
wait till a lock_sock(() task in process context is finished. This
may lead to races in socket state transitions resulting in dangling
SMC-sockets, or it may lead to duplicate SMC socket freeing.
This patch introduces a closing worker to run all state changes under
lock_sock().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake up reading file descriptors for a closing socket as well, otherwise
some socket applications may stall.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If peer indicates write_blocked, the cursor state of the received data
should be send to the peer immediately (in smc_tx_consumer_update()).
Afterwards the write_blocked indicator is cleared.
If there is no free slot for another write request, sending is postponed
to worker smc_tx_work, and the write_blocked indicator is not cleared.
Therefore another clearing check is needed in smc_tx_work().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC requires an active ib port on the RoCE device.
smc_pnet_find_roce_resource() determines the matching RoCE device port
according to the configured PNET table. Do not return the found
RoCE device port, if it is not flagged active.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The global event handler is created only, if the ib_device has already
been used by at least one link group. It is guaranteed that there exists
the corresponding entry in the smc_ib_devices list. Get rid of this
superfluous check.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes an outdated comment.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the submission of the lastest multiple buffer patch set, this fix was lost.
I am sending this patch to put it right again. The fix was originally proposed
by Arnd Bergmann.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF helper functions access socket fields through skb->sk. This is not
set in ingress cgroup and socket filters. The association is only made
in skb_set_owner_r once the filter has accepted the packet. Sk is
available as socket lookup has taken place.
Temporarily set skb->sk to sk in these cases.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the return value check which testing the wrong variable
in devlink_dpipe_header_put().
Fixes: 1555d204e7 ("devlink: Support for pipeline debug (dpipe)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
more s390/net updates
here's a second batch of s390/net patches for net-next.
A mixed bunch of qeth cleanups, and a few patches to add support for
ETHTOOL_GLINKSETTINGS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yan-Hsuan Chuang