Register access to subdevices no longer needs bridge support for those
ioctls. The v4l2 core handles that these days.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mike Isely <isely@isely.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the V4L2_IDENT_* usage with tveeprom-specific defines. This header
is deprecated, so those defines shouldn't be used anymore.
The em28xx driver is the only one that uses the tveeprom audio_processor
field, so that has been updated to use the new tveeprom AUDPROC define.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove g_chip_ident and replace it with g_chip_info.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove g_chip_ident and replace it with g_chip_info.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT has been replaced by VIDIOC_DBG_G_CHIP_INFO. Remove
g_chip_ident support from bridge drivers since it is no longer needed.
This patch takes care of all the trivial cases.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_video_info() should never return EFAULT, instead it should return
the low-level usb_control_msg() error. Add a valid field to the hdpvr_video_info
struct so the driver can easily check if a valid format was detected.
Whenever get_video_info is called and it returns an error (e.g. usb_control_msg
failed), then return that error to userspace as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove an unnecessary 'else' and invert a condition which makes the code
more readable.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If no format has been detected, then querystd should return V4L2_STD_UNKNOWN,
not V4L2_STD_ALL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The device has been tested on a MIPSel box with kernel 3.1.1 and backported media_tree drivers
The kernel detects the device with the following output:
usbcore: registered new interface driver dvb_usb_rtl28xxu
usb 1-2: dvb_usb_v2: found a 'Crypto Redi PC50A' in warm state
usb 1-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Crypto Redi PC50A)
usb 1-2: DVB: registering adapter 1 frontend 0 (Realtek RTL2832 (DVB-T))...
i2c i2c-4: fc0012: Fitipower FC0012 successfully identified
usb 1-2: dvb_usb_v2: 'Crypto Redi PC50A' successfully initialized and connected
[crope@iki.fi: fix trivial merge conflict]
Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
USB ID 0413:6a03 is Leadtek WinFast DTV Dongle mini.
Decoder Realtek RTL2832U and tuner Infineon TUA9001.
Signed-off-by: Miroslav Šustek <sustmidown@centrum.cz>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
This patch uses the driver from openpli[1] as a template to restore the remote control support.
I had to divert from the original to use the in kernel rc protocol decoder. The key repetition does,
not seem to work but I cant find the problem in the driver. As a raw rc provider, no key table is
hardcoded.
Rodrigo.
[1]: https://aur.archlinux.org/packages/dvb-usb-rtl2832u-openpli/?comments=all
Signed-off-by: Rodrigo Tartajo <rtarty@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested on a MIPSel box with 3.3.6 kernel
The kernel output when the device will be detected follows:
usbcore: registered new interface driver dvb_usb_it913x
it913x: Chip Version=01 Chip Type=9135
it913x: Remote propriety (raw) mode
it913x: Dual mode=3 Tuner Type=38
it913x: Chip Version=01 Chip Type=9135
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in cold state
usb 2-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9137-01.fw'
it913x: FRM Starting Firmware Download
it913x: FRM Firmware Download Completed - Resetting Device
it913x: Chip Version=01 Chip Type=9135
it913x: Firmware Version 204147968
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in warm state
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 1 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_1)...
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 2 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_2)...
usb 2-1: dvb_usb_v2: 'Digital Dual TV Receiver CTVDIGDUAL_V2' successfully initialized and connected
RC part not tested
Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Maintaining the users count using an atomic variable makes sure that
access to the counter won't be racy, but doesn't serialize access to the
operations protected by the counter. This creates a race condition that
could result in the status URB being submitted multiple times.
Use a mutex to protect the users count and serialize access to the
status start and stop operations.
Reported-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
BugLink: http://bugs.launchpad.net/bugs/1180409
OminiVision webcam 0x05a9:0x2643 needs the same UVC_QUIRK_PROBE_DEF
as other OmniVision models to work properly.
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
BugLink: https://bugs.launchpad.net/bugs/1168430
OminiVision webcam 0x05a9:0x264a (in Dell Studio Hybrid 140g) needs the
same UVC_QUIRK_PROBE_DEF as other OmniVision model to be recognized
consistently.
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes check for EPERM in vidioc_g/s_register
as this check is already performed by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix hdpvr build errors when CONFIG_I2C=m and VIDEO_V4L2=m and
VIDEO_HDPVR=y.
drivers/built-in.o: In function `hdpvr_disconnect':
hdpvr-core.c:(.text+0xef542): undefined reference to `v4l2_device_disconnect'
hdpvr-core.c:(.text+0xef57e): undefined reference to `i2c_del_adapter'
hdpvr-core.c:(.text+0xef58a): undefined reference to `video_unregister_device'
drivers/built-in.o: In function `hdpvr_delete':
(.text+0xef5b9): undefined reference to `video_device_release'
drivers/built-in.o: In function `hdpvr_probe':
hdpvr-core.c:(.text+0xef63a): undefined reference to `v4l2_device_register'
hdpvr-core.c:(.text+0xefd97): undefined reference to `i2c_del_adapter'
drivers/built-in.o: In function `hdpvr_s_ctrl':
hdpvr-video.c:(.text+0xf03c0): undefined reference to `v4l2_ctrl_activate'
drivers/built-in.o: In function `hdpvr_device_release':
hdpvr-video.c:(.text+0xf0470): undefined reference to `v4l2_device_unregister'
hdpvr-video.c:(.text+0xf0479): undefined reference to `v4l2_ctrl_handler_free'
hdpvr-video.c:(.text+0xf048f): undefined reference to `i2c_del_adapter'
drivers/built-in.o: In function `hdpvr_open':
hdpvr-video.c:(.text+0xf0570): undefined reference to `video_devdata'
hdpvr-video.c:(.text+0xf057b): undefined reference to `v4l2_fh_init'
hdpvr-video.c:(.text+0xf0583): undefined reference to `v4l2_fh_add'
drivers/built-in.o: In function `video_drvdata':
hdpvr-video.c:(.text+0xf08a0): undefined reference to `video_devdata'
drivers/built-in.o: In function `vidioc_s_dv_timings':
hdpvr-video.c:(.text+0xf0d34): undefined reference to `v4l_match_dv_timings'
drivers/built-in.o: In function `hdpvr_poll':
hdpvr-video.c:(.text+0xf1455): undefined reference to `v4l2_ctrl_poll'
drivers/built-in.o: In function `hdpvr_release':
hdpvr-video.c:(.text+0xf18f6): undefined reference to `v4l2_fh_release'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1be3): undefined reference to `v4l2_ctrl_handler_init_class'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c19): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c42): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c6b): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1cac): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1cd5): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o:(.text+0xf1cfe): more undefined references to `v4l2_ctrl_new_std' follow
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1d75): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1d9e): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1dc3): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1de5): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e18): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e4b): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e90): undefined reference to `v4l2_ctrl_cluster'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e98): undefined reference to `v4l2_ctrl_handler_setup'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1ec1): undefined reference to `video_device_alloc'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1f85): undefined reference to `__video_register_device'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1fac): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `hdpvr_register_ir_tx_i2c':
(.text+0xf238f): undefined reference to `i2c_new_device'
drivers/built-in.o: In function `hdpvr_register_ir_rx_i2c':
(.text+0xf2434): undefined reference to `i2c_new_device'
drivers/built-in.o: In function `hdpvr_register_i2c_adapter':
(.text+0xf2514): undefined reference to `i2c_add_adapter'
drivers/built-in.o:(.rodata+0x1b368): undefined reference to `video_ioctl2'
drivers/built-in.o:(.rodata+0x1b690): undefined reference to `v4l2_ctrl_log_status'
drivers/built-in.o:(.rodata+0x1b6f8): undefined reference to `v4l2_ctrl_subscribe_event'
drivers/built-in.o:(.rodata+0x1b700): undefined reference to `v4l2_event_unsubscribe'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the enum values have changed recently, the comments are void.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
(a.k.a. Kconfig bool depending on a tristate considered harmful)
Fix various build errors when CONFIG_USB=m and media USB drivers
are builtin. In this case, CONFIG_USB_ZR364XX=y,
CONFIG_VIDEO_PVRUSB2=y, and CONFIG_VIDEO_STK1160=y.
This is caused by (from drivers/media/usb/Kconfig):
menuconfig MEDIA_USB_SUPPORT
bool "Media USB Adapters"
depends on USB && MEDIA_SUPPORT
=m =y
so MEDIA_USB_SUPPORT=y and all following Kconfig 'source' lines
are included. By adding an "if USB" guard around most of this file,
the needed dependencies are enforced.
drivers/built-in.o: In function `zr364xx_start_readpipe':
zr364xx.c:(.text+0xc726a): undefined reference to `usb_alloc_urb'
zr364xx.c:(.text+0xc72bb): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `zr364xx_stop_readpipe':
zr364xx.c:(.text+0xc72fd): undefined reference to `usb_kill_urb'
zr364xx.c:(.text+0xc7309): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `read_pipe_completion':
zr364xx.c:(.text+0xc7acc): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `send_control_msg.constprop.12':
zr364xx.c:(.text+0xc7d2f): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_ctl_timeout':
pvrusb2-hdw.c:(.text+0xcadb6): undefined reference to `usb_unlink_urb'
pvrusb2-hdw.c:(.text+0xcadcb): undefined reference to `usb_unlink_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc42c): undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc448): undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc5f9): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc65a): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc666): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_send_request_ex.part.22':
pvrusb2-hdw.c:(.text+0xccbe3): undefined reference to `usb_submit_urb'
pvrusb2-hdw.c:(.text+0xccc83): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `pvr2_hdw_remove_usb_stuff.part.25':
pvrusb2-hdw.c:(.text+0xcd3f9): undefined reference to `usb_kill_urb'
pvrusb2-hdw.c:(.text+0xcd405): undefined reference to `usb_free_urb'
pvrusb2-hdw.c:(.text+0xcd421): undefined reference to `usb_kill_urb'
pvrusb2-hdw.c:(.text+0xcd42d): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_hdw_device_reset':
(.text+0xcd658): undefined reference to `usb_lock_device_for_reset'
drivers/built-in.o: In function `pvr2_hdw_device_reset':
(.text+0xcd664): undefined reference to `usb_reset_device'
drivers/built-in.o: In function `pvr2_hdw_cpureset_assert':
(.text+0xcd6f9): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_hdw_cpufw_set_enabled':
(.text+0xcd84e): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_upload_firmware1':
pvrusb2-hdw.c:(.text+0xcda47): undefined reference to `usb_clear_halt'
pvrusb2-hdw.c:(.text+0xcdb04): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_upload_firmware2':
(.text+0xce7dc): undefined reference to `usb_bulk_msg'
drivers/built-in.o: In function `pvr2_stream_buffer_count':
pvrusb2-io.c:(.text+0xd2e05): undefined reference to `usb_alloc_urb'
pvrusb2-io.c:(.text+0xd2e5b): undefined reference to `usb_kill_urb'
pvrusb2-io.c:(.text+0xd2e9f): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_stream_internal_flush':
pvrusb2-io.c:(.text+0xd2f9b): undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `pvr2_buffer_queue':
(.text+0xd3328): undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `pvr2_buffer_queue':
(.text+0xd33ea): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `stk1160_read_reg':
(.text+0xd3efa): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `stk1160_write_reg':
(.text+0xd3f4f): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `stop_streaming':
stk1160-v4l.c:(.text+0xd4997): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `start_streaming':
stk1160-v4l.c:(.text+0xd4a9f): undefined reference to `usb_set_interface'
stk1160-v4l.c:(.text+0xd4afa): undefined reference to `usb_submit_urb'
stk1160-v4l.c:(.text+0xd4ba3): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `stk1160_isoc_irq':
stk1160-video.c:(.text+0xd509b): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `stk1160_cancel_isoc':
(.text+0xd50ef): undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `stk1160_free_isoc':
(.text+0xd5155): undefined reference to `usb_free_coherent'
drivers/built-in.o: In function `stk1160_free_isoc':
(.text+0xd515d): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `stk1160_alloc_isoc':
(.text+0xd5278): undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `stk1160_alloc_isoc':
(.text+0xd52c2): undefined reference to `usb_alloc_coherent'
drivers/built-in.o: In function `stk1160_alloc_isoc':
(.text+0xd53c4): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `zr364xx_driver_init':
zr364xx.c:(.init.text+0x463e): undefined reference to `usb_register_driver'
drivers/built-in.o: In function `pvr_init':
pvrusb2-main.c:(.init.text+0x4662): undefined reference to `usb_register_driver'
drivers/built-in.o: In function `stk1160_usb_driver_init':
stk1160-core.c:(.init.text+0x467d): undefined reference to `usb_register_driver'
drivers/built-in.o: In function `zr364xx_driver_exit':
zr364xx.c:(.exit.text+0x1377): undefined reference to `usb_deregister'
drivers/built-in.o: In function `pvr_exit':
pvrusb2-main.c:(.exit.text+0x1389): undefined reference to `usb_deregister'
drivers/built-in.o: In function `stk1160_usb_driver_exit':
stk1160-core.c:(.exit.text+0x13a0): undefined reference to `usb_deregister'
Suggested-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hardware is the same as MaxMedia UB425-TC but ships with a different
remote.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some unknown reason we need to increase hstart by 1 on when using the
PAS202 on the sn9c103 (versus on the sn9c102), otherwise we get the wrong
colors, due to shifting of the bayer pattern.
Reported-by: Patrizio Bassi <patrizio.bassi@gmail.com>
Tested-by: Patrizio Bassi <patrizio.bassi@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With all the changes to handle the locking in the v4l2-core rather then at
the driver level, the order in which the 2 pwc locks need to be taken has
changed, update the comment in the header file to correctly reflect this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media update from Mauro Carvalho Chehab:
- OF documentation and patches at core and drivers, to be used by for
embedded media systems
- some I2C drivers used on go7007 were rewritten/promoted from staging:
sony-btf-mpx, tw2804, tw9903, tw9906, wis-ov7640, wis-uda1342
- add fimc-is driver (Exynos)
- add a new radio driver: radio-si476x
- add a two new tuners: r820t and tuner_it913x
- split camera code on em28xx driver and add more models
- the cypress firmware load is used outside dvb usb drivers. So, move
it to a common directory to make easier to re-use it
- siano media driver updated to work with sms2270 devices
- several work done in order to promote go7007 and solo6x1x out of
staging (still, there are some pending issues)
- several API compliance fixes at v4l2 drivers that don't behave as
expected
- as usual, lots of driver fixes, improvements, cleanups and new device
addition at the existing drivers.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (831 commits)
[media] cx88: make core less verbose
[media] em28xx: fix oops at em28xx_dvb_bus_ctrl()
[media] s5c73m3: fix indentation of the help section in Kconfig
[media] cx25821-alsa: get rid of a __must_check warning
[media] cx25821-video: declare cx25821_vidioc_s_std as static
[media] cx25821-video: remove maxw from cx25821_vidioc_try_fmt_vid_cap
[media] r820t: Remove a warning for an unused value
[media] dib0090: Fix a warning at dib0090_set_EFUSE
[media] dib8000: fix a warning
[media] dib8000: Fix sub-channel range
[media] dib8000: store dtv_property_cache in a temp var
[media] dib8000: warning fix: declare internal functions as static
[media] r820t: quiet gcc warning on n_ring
[media] r820t: memory leak in release()
[media] r820t: precendence bug in r820t_xtal_check()
[media] videodev2.h: Remove the unused old V4L1 buffer types
[media] anysee: Grammar s/report the/report to/
[media] anysee: Initialize ret = 0 in anysee_frontend_attach()
[media] media: videobuf2: fix the length check for mmap
[media] em28xx: save isoc endpoint number for DVB only if endpoint has alt settings with xMaxPacketSize != 0
...
* topic/r820t: (31 commits)
[media] r820t: Don't divide the IF by two
[media] r820t: disable auto gain/VGA setting
[media] rtl2832: Fix IF calculus
[media] r820t: put it into automatic gain mode
[media] r820t: Fix hp_cor filter mask
[media] r820t: fix PLL calculus
[media] r820t: Don't put it in standby if not initialized yet
[media] r820t: avoid rewrite all regs when not needed
[media] r820t: Allow disabling IMR callibration
[media] r820t: add a commented code for GPIO
[media] r820t: add IMR calibrate code
[media] r820t: proper initialize the PLL register
[media] r820t: use usleep_range()
[media] r820t: fix prefix of the r820t_read() function
[media] r820t: split the function that read cached regs
[media] r820t: better report signal strength
[media] r820t: add support for diplexer
[media] r820t: Show the read data in the bit-reversed order
[media] r820t: use the second table for 7MHz
[media] r820t: Invert bits for read ops
...
drivers/media/usb/dvb-usb-v2/anysee.c: In function ‘anysee_frontend_attach’:
drivers/media/usb/dvb-usb-v2/anysee.c:641: warning: ‘ret’ may be used uninitialized in this function
And gcc is right (see the ANYSEE_HW_507T case), so initialize ret to zero
to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
In addition to commit 72cc9ba3 "em28xx: ignore isoc DVB USB endpoints with
wMaxPacketSize = 0 bytes for all alt settings" we should not save the endpoint
number of the isoc DVB endpoint before it has been validated.
While the current code works fine, dev->dvb_ep_isoc != 0 could be interpreted
as indicator that the device provides DVB support.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The intend of this patch is to improve the support of the dib7090 and
dib7790. The AGC1 min value is set to 32768 by default. The actual AGC1 min
and the external attenuation are controled depending on the received RF
level.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The intend of this patch is to remove the support for the dib7090E. The
DiB7090E-package has never left prototype state and never made it to
mass-prod-state.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The intend of this patch is to improve the support of the dib8096. The PLL
parameters are not automatically computed. The limit to set/unset external
diode for attenuation has been updated. The TFE8096P board is using the
new I2C API.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The intend of this patch is to improve the support of the dib8000.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
commit 61ff5d69 "em28xx: improve em2710/em2820 distinction" missed the
le16_to_cpu conversion of the USB vendor ID.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we can get the strength from r820t, use it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
This tuner is used on some rtl2882 dongles. Add it to the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
There are three drivers with *it913x name on it, and they all
belong to the same device:
a tuner, at it913x.c;
a frontend: it913x-fe.c;
a bridge: it913x.c, renamed to dvb_usb_it913x by the
building system.
This is confusing. Even more confusing are the two .c files with
the same name under different directories, with different contents
and different functions. So, prepend the tuner one.
This also breaks the out-of-tree compilation system.
Reported-by: Frederic Fays <frederic.fays@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit cd634f1 ("[media] v4l2: put VIDIOC_DBG_G_CHIP_NAME under
ADV_DEBUG") missed the initializer of radio_ioctl_ops:
drivers/media/usb/em28xx/em28xx-video.c:1830:2: error: unknown field 'vidioc_g_chip_info' specified in initializer
drivers/media/usb/em28xx/em28xx-video.c:1830:26: error: 'vidioc_g_chip_info' undeclared here (not in a function)
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chip id 18 is used by the em2710 and em2820.
The current code assumes that if the device is a camera, the chip is an em2710
and an em2820 otherwise.
But it turned out that the em2820 is also used in camera devices.
"Silvercrest 1.3 MPix" webcams for example are available with both chips.
Fortunately both variants are using different generic USD IDs which give us a
hint about the used chip.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The snapshot button support is currently broken, because module em28xx-rc is
loaded only if the device has remote control support.
Fix it by also loading this module if the device has a snapshot button.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both MythTV and gstreamer expect that they can set/get/query/enumerate the
standards, even if the input is the component input for which standards
really do not apply.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the latest firmware version and - it seems - the most reliable.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Video nodes can be used at once after registration, so make sure the full
initialization is done before registering them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This prepares the driver for priority and control event handling.
This patch also checks for correct streaming ownership and it makes a
small improvement to the encoder_cmd ioctls: always zero 'flags' and
drop the memset of 'raw' as that is already done by the v4l2 core.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb->adapter.priv should also be set to the i2c bus since that's what
em28xx_tuner_callback expects.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl will be extended to return more information than just the name.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only enable this ioctl if the VIDEO_ADV_DEBUG config option is set. This
prevents abuse from both userspace and kernelspace (some bridge drivers
abuse DBG_G_CHIP_IDENT, lets prevent that from happening again with this
ioctl).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"enum dmx_ts_pes" and "typedef enum dmx_pes_type_t" are just the
same enum declared twice, since Kernel (2.6.12). There's no reason
to duplicate it there, and sparse complains about that:
drivers/media/dvb-core/dmxdev.c:600:55: warning: mixing different enum types
So, remove the internal define, keeping just the external one.
Internally, use only "enum dmx_ts_pes", as it is too late to drop
dmx_pes_type_t from the userspace API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/usb/dvb-usb/m920x.c:91:6: warning: "ret" may be used uninitialized in this function [-Wuninitialized]
drivers/media/usb/dvb-usb/m920x.c:70:6: note: "ret" was declared here
This is real, if a remote control has an empty initialization sequence
we would get success or failure randomly.
OTOH the initialization of ret in m920x_init is needless, the function
returns with an error as soon as an error happens, so the last return
can only be a success and we can hard-code 0 there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx: fix typo in scale_to_size().
The second hscale should be vscale. This bug caused xawtv to fail because it
cannot find a workable image size.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Loading the cypress firmware is not dvb specific and should be common
functionality. Move the source to media/common and make it a standalone
module.
As a result we can remove the dependency on dvb-usb in go7007, which has
nothing to do with dvb.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The et61x251 driver was removed in v3.5. Remove the last references to
its Kconfig macro now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This sensor is used by the "SpeedLink Vicious And Devine Laplace webcam" and
others. It supports resolutions up to 1600x1200 (at 7-8 fps), but for
resolutions higher than 640x480, further driver changes will be necessary,
such as sensor output resolution switching (including further configuration
changes), bridge xclk adjustment and disabling of 16 bit (12 bit) output formats
at high resolutions. Image quality should also needs to be improved.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Windows driver also probes at least two further i2c addresses (0x22 >> 1
and 0x66 >> 1). I've got some hints that they are very likely used by Samsung
and Kodak sensors, which are known to be used in Empia devices, too.
We havn't seen any devices using these sensors yet and don't know how to probe
them properly, so leave a comment.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OmniVision sensors are used as well in Empiatech based cameras such as the
"SpeedLink Vicious And Devine Laplace" webcam (EM2765 + Omnivision OV2640).
With this patch applied, OminiVision sensors with 8 bit address and register
width are detected (recent models have a 16 bit address width and use different
client addresses).
The most commonly used sensors (including the ones listed by Empiatech) are
detected properly, although there is no support for them yet.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Other sensors like the ones from OmniVision need a different probing procedure,
so it makes sense have separate functions for each manufacturer/sensor type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add further Micron chip IDs to be able to identify all Micron sensors listed
by Empiatech.
Also probe the two alternate i2c addresses used by Micron sensors with 8 bit
address and 16 bit register width.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx-cards.c is very large and the sensor/camera related code is growing,
so move this code to a separate source code file em28xx-camera.c.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the board hints and the sensor initialization/configuration have been
separated, em28xx_detect_sensor() is the better name for this function.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sensor detection and initialization/configuration are currently mixed together.
This works as long as all devices with a particular sensor are working with the
same board configuration. In the long run, this will be not sufficient, so
separate these both steps to make the code more flexible and future proof.
This also makes the code more consistent, because the initialization of the
MT9V011 sensor subdevice is already separated.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current board hint code is mixed together with the sensor detection and
initialization code. It actually selects a board depending on the detected
sensor type only, with the result that 3 of the 6 webcam boards are currently
dead.
Separate it and move it to em28xx_hint_board() which already contains the board
hints for analog capturing+TV and DVB devices.
This way, we have all board hints at a common place which makes it easier
to extend the code and reduces the risk of regressions.
It also makes it possible again to use the boards EM2750_BOARD_DLCW_130,
EM2820_BOARD_VIDEOLOGY_20K14XUSB and EM2860_BOARD_NETGMBH_CAM (using the module
parameter "card").
NOTE: the current board hint logic for webcams is preserved. Not more not less.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices without DVB support (such as the "Terratec Grabby" and
"Easycap DC-60") provide isochronous DVB USB endpoints with wMaxPacketSize set
to 0 bytes for all alt settings.
Ignore these endpoints and avoid registering a DVB device node and loading the
DVB driver extension.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-ERANGE is the right error code when the value is outside of the menu
range, but -EINVAL must be reported for invalid values inside the range.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Windows driver writes the output resolution to registers 0x34 (width / 16)
and 0x35 (height / 16) always.
We don't know yet what these registers are used for.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Streaming doesn't work with the EM2765 if bit 5 of the output format register
0x27 is set.
It's actually not clear if really has to be set for the other chips, but for
now let's keep it to avoid regressions and add a comment to the code.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em25xx/em276x/em277x/em278x frame data format is different to the one used
by the em2710/em2750/em28xx chips.
With the recent cleanups and reorganization of the frame data processing code it
can be easily extended to support these devices.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This chip can be found in the SpeedLink VAD Laplace webcam (1ae7:9003 and 1ae7:9004).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcam "SpeedLink VAD Laplace" (em2765 + ov2640) uses a special algorithm
for i2c communication with the sensor, which is connected to a second i2c bus.
We don't know yet how to find out which devices support/use it.
It's very likely used by all em25xx and em276x+ bridges.
Tests with other em28xx chips (em2820, em2882/em2883) show, that this
algorithm always succeeds there although no slave device is connected.
The algorithm likely also works for real i2c client devices (OV2640 uses SCCB),
because the Windows driver seems to use it for probing Samsung and Kodak
sensors.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the missing unlock before return from function af9035_ctrl_msg()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- open/close/read and poll need to take the core lock as well.
- when the tuner goes to sleep we should set std_set_in_tuner_core
to 0 since the tuner loses the firmware at that time.
- initialize the tuner if std_set_in_tuner_core == 0 whenever:
1) g/s_tuner, s_std or s_frequency is called
2) read or poll is called
3) streamon is called
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After loading the module the initial video routing is not setup.
Explicitly call s_input to get this right.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just opening a device shouldn't have any side-effects.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Turn it into a simple function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver crashed when the device was disconnected while an application
still had a device node open. Fixed by using the release() callback of struct
v4l2_device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also get rid of unnecessary format type check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil