* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (110 commits)
sh: i2c-sh7760: Replase from ctrl_* to __raw_*
sh: clkfwk: Shuffle around to match the intc split up.
sh: clkfwk: modify for_each_frequency end condition
sh: fix clk_get() error handling
sh: clkfwk: Fix fault in frequency iterator.
sh: clkfwk: Add a helper for rate rounding by divisor ranges.
sh: clkfwk: Abstract rate rounding helper.
sh: clkfwk: support clock remapping.
sh: pci: Convert to upper/lower_32_bits() helpers.
sh: mach-sdk7786: Add support for the FPGA SRAM.
sh: Provide a generic SRAM pool for tiny memories.
sh: pci: Support secondary FPGA-driven PCIe clocks on SDK7786.
sh: pci: Support slot 4 routing on SDK7786.
sh: Fix up PMB locking.
sh: mach-sdk7786: Add support for fpga gpios.
sh: use pr_fmt for clock framework, too.
sh: remove name and id from struct clk
sh: free-without-alloc fix for sh_mobile_lcdcfb
sh: perf: Set up perf_max_events.
sh: perf: Support SH-X3 hardware counters.
...
Fix up trivial conflicts (perf_max_events got removed) in arch/sh/kernel/perf_event.c
Provide a mechanism that allows running code in IRQ context. It is
most useful for NMI code that needs to interact with the rest of the
system -- like wakeup a task to drain buffers.
Perf currently has such a mechanism, so extract that and provide it as
a generic feature, independent of perf so that others may also
benefit.
The IRQ context callback is generated through self-IPIs where
possible, or on architectures like powerpc the decrementer (the
built-in timer facility) is set to generate an interrupt immediately.
Architectures that don't have anything like this get to do with a
callback from the timer tick. These architectures can call
irq_work_run() at the tail of any IRQ handlers that might enqueue such
work (like the perf IRQ handler) to avoid undue latencies in
processing the work.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[ various fixes ]
Signed-off-by: Huang Ying <ying.huang@intel.com>
LKML-Reference: <1287036094.7768.291.camel@yhuang-dev>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that we've got a generic perf-events based oprofile backend we might
as well make use of it seeing as SH doesn't do anything special with its
oprofile backend. Also introduce a new CONFIG_HW_PERF_EVENTS symbol so
that we can fallback to using the timer interrupt for oprofile if the
CPU doesn't support perf events.
Also, to avoid a section mismatch warning we need to annotate
oprofile_arch_exit() with an __exit marker.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
The SH-X3 proto CPU has all of the external IRQ and IRL pins muxed, make
sure that we're able to grab them before attempting to register their
respective IRQ controllers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When executing:
make ARCH=sh defconfig
kconfig segfaulted.
kconfig should obviously not segfault.
But this indicated a problem in the sh files which was
tracked down to a recursive dependency.
We select HAVE_HW_BREAKPOINT and in the following line
we use the same symbol in an expression.
Drop the conditional as it is of no use.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that all arches have been converted over to use generic time via
clocksources or arch_gettimeoffset(), we can remove the GENERIC_TIME
config option and simplify the generic code.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-4-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
via following scripts
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/lmb/memblock/g' \
-e 's/LMB/MEMBLOCK/g' \
$FILES
for N in $(find . -name lmb.[ch]); do
M=$(echo $N | sed 's/lmb/memblock/g')
mv $N $M
done
and remove some wrong change like lmbench and dlmb etc.
also move memblock.c from lib/ to mm/
Suggested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This follows the x86/ppc changes for kprobe-based event tracing on sh.
While kprobes is only supported on 32-bit sh, we provide the API for
HAVE_REGS_AND_STACK_ACCESS_API for both 32 and 64-bit.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This extends some of the existing special casing for HAS_IOPORT
platforms and gets it to the point where platforms can begin to
conditionally select it.
The major changes here are that the PIO routines themselves go away
completely, including all of the machvec port mapping wrappers. With this
in place it's possible for any non-machvec abusing platform to disable
PIO completely. At present this is left as an opt-in until the abusers
are the odd ones out instead of the majority.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is V2 of the MMCIF romImage boot support
for sh7724 and the Ecovec board. With this patch
applied and CONFIG_ROMIMAGE_MMCIF selected the
romImage kernel image can be written to a MMC card
and booted directly by the sh7724 cpu.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are only two ways to define sg_dma_len(); use sg->dma_length or
sg->length. This patch introduces NEED_SG_DMA_LENGTH that enables
architectures to choose sg->dma_length or sg->length.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (127 commits)
sh: update defconfigs.
sh: Fix up the NUMA build for recent LMB changes.
sh64: provide a stub per_cpu_trap_init() definition.
sh: fix up CONFIG_KEXEC=n build.
sh: fixup the docbook paths for clock framework shuffling.
driver core: Early dev_name() depends on slab_is_available().
sh: simplify WARN usage in SH clock driver
sh: Check return value of clk_get on ms7724
sh: Check return value of clk_get on ecovec24
sh: move sh clock-cpg.c contents to drivers/sh/clk-cpg.c
sh: move sh clock.c contents to drivers/sh/clk.
sh: move sh asm/clock.h contents to linux/sh_clk.h V2
sh: remove unused clock lookup
sh: switch boards to clkdev
sh: switch sh4-202 to clkdev
sh: switch shx3 to clkdev
sh: switch sh7757 to clkdev
sh: switch sh7763 to clkdev
sh: switch sh7780 to clkdev
sh: switch sh7786 to clkdev
...
There's still quite a bit of shootdown logic that needs to be hacked up
to support SMP for kdump properly, so just add in a BROKEN_ON_SMP
dependency for now.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are two outstanding fashions for archs to implement hardware
breakpoints.
The first is to separate breakpoint address pattern definition
space between data and instruction breakpoints. We then have
typically distinct instruction address breakpoint registers
and data address breakpoint registers, delivered with
separate control registers for data and instruction breakpoints
as well. This is the case of PowerPc and ARM for example.
The second consists in having merged breakpoint address space
definition between data and instruction breakpoint. Address
registers can host either instruction or data address and
the access mode for the breakpoint is defined in a control
register. This is the case of x86 and Super H.
This patch adds a new CONFIG_HAVE_MIXED_BREAKPOINTS_REGS config
that archs can select if they belong to the second case. Those
will have their slot allocation merged for instructions and
data breakpoints.
The others will have a separate slot tracking between data and
instruction breakpoints.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: K. Prasad <prasad@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Add CONFIG_VIRTUALIZATION to the SH architecture
and include the virtio code there. Used to enable
the virtio drivers under QEMU.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The UP dependency was inherited from ARM, which seems to have run in to
it due to the stacktrace code not being available for SMP in certain
cases, as we don't have this particular limitation there is no specific
need to block on the SMP dependency.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for hardware-assisted userspace irq masking for
special priority levels. Due to the SR.IMASK interactivity, only some
platforms implement this in hardware (including but not limited to
SH-4A interrupt controllers, and ARM-based SH-Mobile CPUs). Each CPU
needs to wire this up on its own, for now only SH7786 is wired up as an
example.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
IRQ autoprobing hasn't actually worked for us at all since very early in
2.6, but no one seems to have noticed given that none of the drivers
that use it see much testing.
yenta_socket is the odd one out, and that depends on PCI IRQs which are
fixed on all SH platforms anyways. Consequently, turning off autoprobing
fixes up crashes triggered by yenta_socket and at least gets it working
again on r7785rp.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
highlander and r2d are the only remaining ones that were blocking
sparseirq being turned on by default, but it turns out that they already
work fine with it by virtue of register_intc_controller(). As such, we
can kill off the dependencies and turn it on by default.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This uses the new create_irq_nr() to build up the FPGA's desired virtual
IRQ mapping and permits us to finally flip on sparseirq for this board.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Newer SH parts are now commonly shipping with multiple controllers, so
we wire up PCI domain support to deal with them. Shamelessly cloned from
the MIPS implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This rewrites the SH7786 clock framework support completely. It's
reworked to provide all of the DIV4 and MSTP function clocks. This brings
it in line with the current clock framework code and lets us drop SH7786
from the list of CPUs that require legacy CPG handling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently ioremap_prot() uses an unsigned long to pass the pgprot value
around. This results in the upper half of the pgprot being chomped when
using 64-bit pgprots on a 32-bit ABI (X2TLB and SH-5).
As the only users of ioremap_prot() are presently legacy parts, this
doesn't cause too much of an issue. In the future when the interface is
converted to use pgprot_t directly this can be re-enabled for the other
parts, too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As SH has a very sparse IRQ map by default, all new CPUs and boards
benefit from using sparseirq by default. Despite this, there are still a
few stragglers (mostly due to using a fixed IRQ range for their FPGA
IRQ mappings), and these still need to be converted over one by one. As
these are now in the minority, and we do not want to encourage this sort
of brain-damage in newer board ports, we force sparseirq on.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All SH CPUs (with the exception of sh64) support the UBC, so select
HW_BREAKPOINT support by default. This fixes up the build for non-SH4A
targets.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As CPUs are migrated over to more fully-featured clock frameworks of
their own and off of the legacy CPG code, they no longer have any real
need for defining the PCLK value. The PCLK define in itself is already
fairly misleading, as many boards get their input clocks from different
sources, making this value fairly arbitrary anyways.
Outside of the legacy CPG clock framework, the only place where this
value is used is for deriving CLOCK_TICK_RATE, which we set back to the
legacy PIT value that it was before the PCLK definitions were added in
the first place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the x86 change to select perf events when hw_breakpoint
support is enabled. This fixes up build issues where perf events can
otherwise be disabled on their own.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Conflict between FPU thread flag migration and debug
thread flag addition.
Conflicts:
arch/sh/include/asm/thread_info.h
arch/sh/include/asm/ubc.h
arch/sh/kernel/process_32.c
This adds preliminary support for the SH-4A UBC to the hw-breakpoints API.
Presently only a single channel is implemented, and the ptrace interface
still needs to be converted. This is the first step to cleaning up the
long-standing UBC mess, making the UBC more generally accessible, and
finally making it SMP safe.
An additional abstraction will be layered on top of this as with the perf
events code to permit the various CPU families to wire up support for
their own specific UBCs, as many variations exist.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The vast majority of SH platforms want this, and the few that don't
aren't going to care one way or the other. Enable it across the board.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that this contains a grand total of 1 Kconfig option, it's hardly
worth keeping split out. Roll CONFIG_PCI back in to the top-level
architecture Kconfig, along with the other bus types.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Leaving this configurable caused more trouble than it was ever worth, so
just make it explicit. Boards that are verified one way or the other can
fix up their selects accordingly. We presently default to non-coherent
for most platforms.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The hugetlb dependencies presently depend on SUPERH && MMU while the
hugetlb page size definitions depend on CPU_SH4 or CPU_SH5. This
unfortunately allows SH-3 + MMU configurations to enable hugetlbfs
without a corresponding HPAGE_SHIFT definition, resulting in the build
blowing up.
As SH-3 doesn't support variable page sizes, we tighten up the
dependenies a bit to prevent hugetlbfs from being enabled. These days
we also have a shiny new SYS_SUPPORTS_HUGETLBFS, so switch to using
that rather than adding to the list of corner cases in fs/Kconfig.
Reported-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code was added for some ancient SH-4 solution engines with peculiar
boot ROMs that did silly things to the UBC MSTP bits. None of these have
been in the wild for years, and these days the clock framework wraps up
the MSTP bits, meaning that the UBC code is one of the few interfaces
that is stomping MSTP bits underneath the clock framework. At this point
the risks far outweigh any benefit this code provided, so just kill it
off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This cribs the x86 implementation of ftrace_nmi_enter() and friends to
make ftrace_modify_code() NMI safe, particularly on SMP configurations.
For additional notes on the problems involved, see the comment below
ftrace_call_replace().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Bye-bye Performance Counters, welcome Performance Events!
In the past few months the perfcounters subsystem has grown out its
initial role of counting hardware events, and has become (and is
becoming) a much broader generic event enumeration, reporting, logging,
monitoring, analysis facility.
Naming its core object 'perf_counter' and naming the subsystem
'perfcounters' has become more and more of a misnomer. With pending
code like hw-breakpoints support the 'counter' name is less and
less appropriate.
All in one, we've decided to rename the subsystem to 'performance
events' and to propagate this rename through all fields, variables
and API names. (in an ABI compatible fashion)
The word 'event' is also a bit shorter than 'counter' - which makes
it slightly more convenient to write/handle as well.
Thanks goes to Stephane Eranian who first observed this misnomer and
suggested a rename.
User-space tooling and ABI compatibility is not affected - this patch
should be function-invariant. (Also, defconfigs were not touched to
keep the size down.)
This patch has been generated via the following script:
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/PERF_EVENT_/PERF_RECORD_/g' \
-e 's/PERF_COUNTER/PERF_EVENT/g' \
-e 's/perf_counter/perf_event/g' \
-e 's/nb_counters/nb_events/g' \
-e 's/swcounter/swevent/g' \
-e 's/tpcounter_event/tp_event/g' \
$FILES
for N in $(find . -name perf_counter.[ch]); do
M=$(echo $N | sed 's/perf_counter/perf_event/g')
mv $N $M
done
FILES=$(find . -name perf_event.*)
sed -i \
-e 's/COUNTER_MASK/REG_MASK/g' \
-e 's/COUNTER/EVENT/g' \
-e 's/\<event\>/event_id/g' \
-e 's/counter/event/g' \
-e 's/Counter/Event/g' \
$FILES
... to keep it as correct as possible. This script can also be
used by anyone who has pending perfcounters patches - it converts
a Linux kernel tree over to the new naming. We tried to time this
change to the point in time where the amount of pending patches
is the smallest: the end of the merge window.
Namespace clashes were fixed up in a preparatory patch - and some
stylistic fallout will be fixed up in a subsequent patch.
( NOTE: 'counters' are still the proper terminology when we deal
with hardware registers - and these sed scripts are a bit
over-eager in renaming them. I've undone some of that, but
in case there's something left where 'counter' would be
better than 'event' we can undo that on an individual basis
instead of touching an otherwise nicely automated patch. )
Suggested-by: Stephane Eranian <eranian@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is necessary to get ftrace syscall tracing working again.. a fairly
trivial and mechanical change. The one benefit is that this can also be
enabled on sh64, despite not having its own ftrace port.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
So far kernel command line arguments could be passed in by a bootloader
or defined as CONFIG_CMDLINE, which completely overwriting the first one.
This change allows a developer to declare selected kernel parameters in
a kernel configuration (eg. project-specific defconfig), retaining
possibility of passing others by a bootloader.
The obvious examples of the first type are MTD partition or
bigphysarea-like region definitions, while "debug" option or network
configuration should be given by a bootloader or a JTAG boot script.
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the Runtime PM driver changes in place, we must have
Runtime PM support in place. Otherwise there is no way to
enable clocks to the Runtime PM enabled hardware blocks.
This patch makes Runtime PM mandatory on SuperH Mobile.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This brings the zImage handling in to the current century, in preparation
for handling the other compression types.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add both dynamic and static function graph tracer support for sh.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that I've added TIF_SYSCALL_FTRACE the thread flags do not fit into
a single byte any more. Code testing them now needs to be aware of the
upper and lower bytes.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable HAVE_FUNCTION_TRACE_MCOUNT_TEST and test the value of
function_trace_stop from our assembly code as opposed to using the
generic C function. This should optimise our mcount/ftrace code path.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rework the bootmem allocator to use the lmb framework.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
That's HAVE_PERF_COUNTERS not HAVE_PERF_COUNTER. This was right
initially but I seem to have screwed it up while re-typing it out
by hand on another machine when I checked it in. Hmph.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7786 is roughly identical to SH-X3 proto SMP, though there are only 2
CPUs. This just wraps in to the existing SH-X3 SMP code with some minor
changes for SH7786, including wiring up the IPIs properly, enabling
IRQ_PER_CPU, and so forth.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Crib the x86 cpu_idle_wait() implementation and shove it in with the
idle code, subsequently enabling ARCH_HAS_CPU_IDLE_WAIT.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables support for the generic software-based perf counters.
Hardware counter support could be added in the future, but the lack
of a performance counter IRQ makes this rather dubious.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the dependent patches are merged, we are ready to enable
sparseirq support. This simply adds the Kconfig option, and then converts
from the _cpu to the _node allocation routines to follow the upstream
sparseirq API changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7722 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
While at it, now when all SuperH Mobile processors
are converted, fix CONFIG_SH_CLK_CPG_LEGACY to depend
on CONFIG_ARCH_SHMOBILE.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7366 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7343 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains V3 of the sh7724 clock framework
rewrite. The new code makes use of the recently merged
div4, div6 and mstp32 helper code. Both extal and fll are
supported as input clocks to the pll. The div6 clocks are
fed through a divide-by-3 block.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains V2 of the sh7723 clock framework
rewrite. The new code makes use of the recently merged
div4, div6 and mstp32 helper code. Both extal and dll
are supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CONFIG_SH_PCLK_FREQ=33333333 is correct for sh7724.
sh7724 master clock is 33333333, but peripheral is 41666666.
This bug came to light because sh-sci driver had changed clk
from "module_clk" to "peripheral_clk"
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This tidies up the boot_cpu_data.flags probing on SH-4A. All of them have
a few things in common, which we can blindly set, rather than having each
subtype have to set the same flags. We can also make assumptions about
cache ways and the validity of PTEA, so this also kills off CPU_HAS_PTEA
as a config option. There was also a bug in the FPU probing, which is now
tidied up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a new SH_CLK_CPG for parts that have CPG support.
SH_CLK_CPG_LEGACY is made to depend on this, and still needs to be set
for platforms that want clock-cpg to register the legacy clocks. With
this new config item in place, it is now possible to start layering more
generic CPG code in place while other platforms transition off of the
legacy clocks.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This updates the SH7785 CPU code as well as the SH7785LCR board support
code for making use of the newly refactored clock framework. Support for
the legacy CPG clocks is dropped at this point, with the extal frequency
fed in from the board code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves out the old legacy CPG clocks to their own file, and converts
over the existing users. With these clocks going away and each CPU
dealing with them on their own, CPUs can gradually move over to the new
interface.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now with all of the TMU users moved over to the new TMU driver, and the
old TMU driver killed off, the left-over infrastructure can go along
with it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the old TMU driver (CONFIG_SH_TMU/timer-tmu.c)
As replacement, select the sh_tmu driver with CONFIG_SH_TIMER_TMU
and configure timer channel using platform data.
If multiple TMU channels are enabled using platform data, use the
earlytimer parameter on the kernel command line to select channel.
For instance, use "earlytimer=sh_tmu.0" to select the first channel.
To verify which timer is being used, look at printouts or the timer
irq count in /proc/interrupts.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds CMT platform data for sh7720 and sh7721.
All 5 32-bit CMT channels unfortunately share a single IRQ.
Both clockevent and clocksource support is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Consolidate these in a single place in the Kconfig menus. At the same
time, disable their interactivity and set them according to the board
config defaults.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The RTC_LIB helpers are used in arch/sh/kernel/time.c, which was
previously only the case for the 32-bit variant. Now that this has
become the common implementation, move the RTC_LIB select to reflect
that. Fixes up the sh64 build.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that everything has converted over to generic timekeeping, we need an
alternate method for keeping the RTC updated for those platforms that are
still using the rtc_sh_get/set_time pairs, presently limited to SH-03 and
the Dreamcast. This wires up the GENERIC_CMOS_UPDATE hooks for those to
maintain the same behaviour.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds sh_tmu support to the SH-5 subtypes, which subsequently allows
us to kill off time_64.c and use the now generic time_32.c. As a bonus,
SH-5 now supports highres timers and tickless for the first time.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The TMU block is supported on all SH-3 and SH-4 subtypes, so just select
it there, rather than conditionalizing it per subtype.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds TMU platform data for sh7785. Both clockevent
and clocksource support is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh64 is still using this, so re-enable it temporarily while SH-5 gets
converted to use the generic code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the rest of the timers that didn't support clockevents have been
rewritten, both of these can be enabled by default.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds TMU platform data for sh7722. Only clockevent
mode is enabled for now, clocksource requires this patch:
"clocksource: setup mult_orig in clocksource_enable()"
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Linus Torvalds