If fec MDIO write method succeeds its return value comes from
call to pm_runtime_get_sync().
But pm_runtime_get_sync() can also return 1.
In case of Micrel KSZ9031 PHY this value will then
be returned along the call chain of phy_write() ->
ksz9031_extended_write() -> ksz9031_center_flp_timing() ->
ksz9031_config_init() -> phy_init_hw() -> phy_attach_direct() ->
phy_connect_direct().
Then phy_connect() will cast it into a pointer using ERR_PTR(),
which then fec_enet_mii_probe() will try to dereference
resulting in an oops.
Fix it by normalizing return value of pm_runtime_get_sync()
to be zero if positive in MDIO write method.
Fixes: 8fff755e9f ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch just to re-submit the patch "db3421c114cfa6326" because the
patch "4d494cdc92b3b9a0" remove the change.
Clear any pending receive interrupt before we process a pending packet.
This helps to avoid any spurious interrupts being raised after we have
fully cleaned the receive ring, while still allowing an interrupt to be
raised if we receive another packet.
The position of this is critical: we must do this prior to reading the
next packet status to avoid potentially dropping an interrupt when a
packet is still pending.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than re-initialising the entire completion on every mdio access,
use reinit_completion() which only resets the completion count. This
avoids possible reinitialisation of the contained spinlock and waitqueue
while they may be in use (eg, mid-completion.)
Such an event could occur if there's a long delay in interrupt handling
causing the mdio accessor to time out, then a second access comes in
while the interrupt handler on a different CPU has called complete().
Another scenario where this has been observed is while locking has
been missing at the phy layer, allowing concurrent attempts to access
the MDIO bus.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some MAC registers that need to be kept in sync
with the link state parameters, see adjust_link().
However, after a MAC soft reset default values for
these registers are assumed. In some cases (excepting
if down/ if up for example) adjust_link() does not see
that these values were reset to default because the
priv->old* link parameters were left unchanged.
So, reset the priv->old* link params as well during a
MAC reset to let adjust_link() restore the MAC link
settings to the actual link state values.
Fixes following case, for example:
Setting link to 100M, changing MTU (implies MAC reset),
link state remains unchanged to 100M but MAC registers
were reset to default (1G) breaking the connectivity w/
the PHY. Closing and re-opening the interface would
restore the MAC link parameters to the correct values.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use the IS_ERR_VALUE() macro for checking
the return value from pm_runtime_* functions.
Just do a simple negative test instead.
The semantic patch that makes this change is available
in scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current filer rule optimization is broken in several ways:
(1) Can perform reads/writes beyond end of allocated tables.
(gianfar_ethtool.c:1326).
(2) It breaks badly for rules with more than 2 specifiers
(e.g. matching ip, port, tos).
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 tos 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 tos 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 tos 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND Q:00 ctrl:00000080 prop:00000210
01: FPR == 00000210 AND CLE Q:00 ctrl:00000281 prop:00000210
02: MASK == ffffffff AND Q:00 ctrl:00000080 prop:ffffffff
03: DPT == 00000003 AND Q:00 ctrl:0000008e prop:00000003
04: TOS == 00000003 AND Q:00 ctrl:0000008a prop:00000003
05: DIA == 0a000003 AND Q:11 ctrl:0000448c prop:0a000003
06: DPT == 00000002 AND Q:00 ctrl:0000008e prop:00000002
07: TOS == 00000002 AND Q:00 ctrl:0000008a prop:00000002
08: DIA == 0a000002 AND Q:09 ctrl:0000248c prop:0a000002
09: DIA == 0a000001 AND Q:00 ctrl:0000008c prop:0a000001
0a: DPT == 00000001 AND Q:00 ctrl:0000008e prop:00000001
0b: TOS == 00000001 CLE Q:01 ctrl:0000060a prop:00000001
ff: MASK >= 00000000 Q:00 ctrl:00000020 prop:00000000
(Entire cluster gets AND-ed together).
(3) We observed that the masking rules it generates do not
play well with clustering on P2020. Only first rule
of the cluster would ever fire. Given that optimizer
relies heavily on masking this is very hard to fix.
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND Q:00 ctrl:00000080 prop:00000210
01: FPR == 00000210 AND CLE Q:00 ctrl:00000281 prop:00000210
02: MASK == ffffffff AND Q:00 ctrl:00000080 prop:ffffffff
03: DPT == 00000003 AND Q:00 ctrl:0000008e prop:00000003
04: DIA == 0a000003 Q:11 ctrl:0000440c prop:0a000003
05: DPT == 00000002 AND Q:00 ctrl:0000008e prop:00000002
06: DIA == 0a000002 Q:09 ctrl:0000240c prop:0a000002
07: DIA == 0a000001 AND Q:00 ctrl:0000008c prop:0a000001
08: DPT == 00000001 CLE Q:01 ctrl:0000060e prop:00000001
ff: MASK >= 00000000 Q:00 ctrl:00000020 prop:00000000
Which looks correct according to the spec but only the first
(eth id 252)/last added rule for 10.0.0.3 will ever trigger.
As if filer did not treat the AND CLE as cluster start but
also kept AND-ing the rules. We found no errata covering this.
The fact that nobody noticed (2) or (3) makes me think
that this feature is not very widely used and we should just
remove it.
Reported-by: Aleksander Dutkowski <adutkowski@gmail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At a cost of one line let's make sure .count is correct
when calling gfar_process_filer_changes().
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_FILER_IDX is the last usable index. Using less-than
will already guarantee that one entry for catch-all rule
will be left, no need to subtract 1 here.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not interested in interrupts for partially transmitted frames.
Unlike SCC and FCC, the FEC doesn't handle the I bit in buffer
descriptors, instead it defines two interrupt bits, TXB and TXF.
We have to mask TXB in order to only get interrupts once the
frame is fully transmitted.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not interested in interrupts for partially transmitted frames,
we have to clear BD_ENET_TX_INTR explicitly otherwise it may remain
from a previously used descriptor.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we transmit a fragmented skb, we may run into a race like the
following scenario (assume txq->cur_tx is next to txq->dirty_tx):
cpu 0 cpu 1
fec_enet_txq_submit_skb
reserve a bdp for the first fragment
fec_enet_txq_submit_frag_skb
update the bdp for the other fragment
update txq->cur_tx
fec_enet_tx_queue
bdp = fec_enet_get_nextdesc(txq->dirty_tx, fep, queue_id);
This bdp is the bdp reserved for the first segment. Given
that this bdp BD_ENET_TX_READY bit is not set and txq->cur_tx
is already pointed to a bdp beyond this one. We think this is a
completed bdp and try to reclaim it.
update the bdp for the first segment
update txq->cur_tx
So we shouldn't update the txq->cur_tx until all the update to the
bdps used for fragments are performed. Also add the corresponding
memory barrier to guarantee that the update to the bdps, dirty_tx and
cur_tx performed in the proper order.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clocks are initially active and thus the device is marked active.
This still keeps the PM refcount at 0, the pm_runtime_put_autosuspend()
call at the end of probe then leaves us with an invalid refcount of -1,
which in turn leads to the device staying in suspended state even though
netdev open had been called.
Fix this by initializing the refcount to be coherent with the initial
device status.
Fixes:
8fff755e9f (net: fec: Ensure clocks are enabled while using mdio bus)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The wol_en flag is 0 by default anyway, and we have the
following inconsistency: a MAGIC packet wol capable eth
interface is registered as a wake-up source but unable
to wake-up the system as wol_en is 0 (wake-on flag set to 'd').
Calling set_wakeup_enable() at netdev open is just redundant
because wol_en is 0 by default.
Let only ethtool call set_wakeup_enable() for now.
The bflock is obviously obsoleted, its utility has been corroded
over time. The bitfield flags used today in gianfar are accessed
only on the init/ config path, with no real possibility of
concurrency - nothing that would justify smth. like bflock.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we disable NAPI in the first place we can mask the device's
interrupts (and halt it) without fearing that imask may be
concurrently accessed from interrupt context, so there's
no need to do local_irq_save() around gfar_halt_nodisable().
lock_rx_qs()/unlock_tx_qs() are just obsoleted and potentially
buggy routines. The txlock is currently used in the driver only
to manage TX congestion, it has nothing to do with halting the
device. With these changes, the TX processing is stopped before
gfar_halt().
Compact gfar_halt() is used instead of gfar_halt_nodisable(),
as it disables Rx/TX DMA h/w blocks and the Rx/TX h/w queues.
gfar_start() re-enables all these blocks on resume. Enabling
the magic-packet mode remains the same, note that the RX block
is re-enabled just before entering sleep mode.
Add IRQF_NO_SUSPEND flag for the error interrupt line, to signal
that the interrupt line must remain active during sleep in order
to wake the system by magic packet (MAG) reception interrupt.
(On some systems the MAG interrupt did trigger w/o this flag
as well, but on others it didn't.)
Without these fixes, when suspended during fair Tx traffic the
interface occasionally failed to be woken up by magic packet.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC drivers/net/ethernet/freescale/gianfar.o
drivers/net/ethernet/freescale/gianfar.c:568:13: warning: 'lock_tx_qs'
defined but not used [-Wunused-function]
static void lock_tx_qs(struct gfar_private *priv)
^
drivers/net/ethernet/freescale/gianfar.c:576:13: warning: 'unlock_tx_qs'
defined but not used [-Wunused-function]
static void unlock_tx_qs(struct gfar_private *priv)
^
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of defconfig consolidation using fragments, we'd like to be
able to have the same drivers enabled on 32-bit and 64-bit. Gianfar
happens to only exist on 32-bit systems, and when building the
resulting 64-bit kernel warnings were produced.
A couple of the warnings are trivial, but the rfbptr code has deeper
issues. It uses the virtual address as the DMA address, which again,
happens to work in the environments where this driver is currently
used, but is not the right thing to do.
Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation
support")
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a switch is attached to the mdio bus, the mdio bus can be used
while the interface is not open. If the IPG clock is not enabled, MDIO
reads/writes will simply time out.
Add support for runtime PM to control this clock. Enable/disable this
clock using runtime PM, with open()/close() and mdio read()/write()
function triggering runtime PM operations. Since PM is optional, the
IPG clock is enabled at probe and is no longer modified by
fec_enet_clk_enable(), thus if PM is not enabled in the kernel, it is
guaranteed the clock is running when MDIO operations are performed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Cc: tyler.baker@linaro.org
Cc: fabio.estevam@freescale.com
Cc: shawn.guo@linaro.org
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function frees resources and cancels delayed work item that
have been initialized in fec_ptp_init().
Use this to do proper error handling if something goes wrong in
probe function after fec_ptp_init has been called.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So it gets freed when the device is going away.
This fixes a DMA memory leak on driver probe() fail and driver
remove().
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment in question is word-for-word copied from ixgbe, and clearly
has no meaning in freescale's driver. (it even says 'return an error'
when the code clearly does not). Remove the comment as it is obviously
incorrect and not applicable to the code as it is today.
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The eTSEC h/w is capable of scatter/gather on the receive side
too if MAXFRM > MRBLR, when the allowed maximum Rx frame size
is set to be greater than the maximum Rx buffer size (MRBLR).
It's about time the driver makes use of this h/w capability,
by supporting fixed buffer sizes and Rx S/G.
The buffer size given to eTSEC for reception is fixed to
1536B (must be multiple of 64), which is the same default
buffer size as before, used to accommodate standard MTU
(1500B) size frames. As before, eTSEC can receive frames of
up to 9600B. Individual Rx buffers are mapped to page halves
(page size for eTSEC systems is 4KB). The skb is built around
the first buffer of a frame (using build_skb()). In case the
frame spans multiple buffers, the trailing buffers are added
as Rx fragments to the skb. The last buffer in frame is marked
by the L status flag. A mechanism is in place to reuse the pages
owned by the driver (for Rx) for subsequent receptions.
Supporting fixed size buffers allows the implementation of Rx S/G,
which in turn removes the memory pressure issues the driver had
before when MTU was set for jumbo frame reception.
Also, in most cases, the Rx path becomes faster due to Rx page
reusal, since the overhead of allocating new rx buffers is removed
from the fast path.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use "ndev" instead of "dev", as the rx queue back pointer
to a net_device struct, to avoid name clashing with a
"struct device" reference. This prepares the addition of a
"struct device" back pointer to the rx queue structure.
Remove duplicated rxq registration in the process.
Move napi_gro_receive() outside gfar_process_frame().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several (long standing) problems about how the status
field of the rx buffer descriptor (rxbd) is currently handled on
the error path:
- too many unnecessary 16bit reads of the two halves of the rxbd
status field (32bit), also resulting in overuse of endianness
convesion macros;
- "bdp->status = RXBD_LARGE" makes no sense, since the "large"
flag is read only (only eTSEC can write it), and trying to clear
the other status bits is also error prone in this context
(most of the rx status bits are read only anyway).
This is fixed with a single 32bit read of the "status" field,
and then the appropriate 16bit shifting is applied to access
the various status bits or the rx frame length. Also corrected
the use of the RXBD_LARGE flag.
Additional fix:
"rx_over_errors" stat is incremented instead of "rx_crc_errors"
in case of RXBD_OVERRUN occurrence.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more common consumer/ producer index design to improve
rx buffer allocation. Instead of allocating a single new buffer
(skb) on each iteration, bundle the allocation of several rx
buffers at a time. This also opens the path for further memory
optimizations.
Remove useless check of rxq->rfbptr, since this patch touches
rx pause frame handling code as well. rxq->rfbptr is always
initialized as part of Rx BD ring init.
Remove redundant (and misleading) 'amount_pull' parameter.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6c3e921b18.
commit 6c3e921b18 ("net: fec: Ensure clocks are enabled while using mdio
bus") prevents the kernel to boot on mx6 boards, so let's revert it.
Reported-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a switch is attached to the mdio bus, the mdio bus can be used
while the interface is not open. If the IPG clock is not enabled, MDIO
reads/writes will simply time out.
Add support for runtime PM to control this clock. Enable/disable this
clock using runtime PM, with open()/close() and mdio read()/write()
function triggering runtime PM operations. Since PM is optional, the
IPG clock is enabled at probe and is no longer modified by
fec_enet_clk_enable(), thus if PM is not enabled in the kernel, it is
guaranteed the clock is running when MDIO operations are performed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all silicon implementations of the Freescale FEC hardware module
have the RACC (Receive Accelerator Function) register, so we should not
be trying to access it on those that don't. Currently none of the ColdFire
based parts with a FEC have it.
Support for RACC was introduced by commit 4c09eed9 ("net: fec: Enable imx6
enet checksum acceleration"). A fix was introduced in commit d1391930
("net: fec: Fix build for MCF5272") that disables its use on the ColdFire
M5272 part, but it doesn't fix the general case of other ColdFire parts.
To fix we create a quirk flag, FEC_QUIRK_HAS_RACC, and check it before
working with the RACC register.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_GIANFAR is not depended on FSL_SOC, it
can be built on non-PPC platforms.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Below case causes mii bus probe failed:
ifconfig eth0 down -> suspend/resume with Mega/fax mix off -> ifconfig eth0 up
In i.MX6SX/i.MX7D chip, Mega/fast mix off feature is supported that means most of
SOC power will be off including ENET MAC for power saving. Once ENET MAC power
off, all initialized MAC registers reset to default, so in the case, it must
init MAC prior to mii bus probe.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver adjust freq formula is:
fe * diff = ppb * pc
Note:
fe: ENET ref clock frequency in Hz
diff = inc_corr - inc: difference between default increment and correction increment
ppb: parts per billion adjustment from base
pc: correction period (in number of fe clock cycles)
The correction increment will be used after N cycles of regular increments,
not every N cycles (with N being the correction period). For example, set ENET_ATCOR=4,
INC=8, INC_CORR=9, there will be 4 increments of 8 (ENET_ATINC[INC]) , followed by 1
increment of 9 (ENET_ATINC[INC_CORR]).
So, the correct formula is:
fe * diff = ppb * (pc + 1)
For ENET_ATCOR, a value 0 disables the correction counter and no corrections occur.
So base on the origin formula, set pc = pc > 1 ? pc - 1 : pc.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the ethtool's "-d" and "--register-dump"
options for fec devices.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use device flag IFF_LIVE_ADDR_CHANGE to signal that
the device supports changing the hardware address when
the device is running.
This allows eth_mac_addr() to change the mac address
also when the network device's interface is open.
This capability is required by certain applications,
like bonding mode 6 (Adaptive Load Balancing).
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle TxFIFO underrun exceptions outside the fast path.
A controller reset is more reliable in this exceptional
case, as opposed to re-enabling on-the-fly the Tx DMA.
As the controller reset is handled outside the fast path
by the reset_gfar() workqueue handler, the locking
scheme on the Tx path is significantly simplified.
Because the Tx processing (xmit queues and tx napi) is
disabled during controller reset, tstat access from xmit
does not require locking. So the scope of the txlock on
the processing path is now reduced to num_txbdfree, which
is shared only between process context (xmit) and softirq
(clean_tx_ring). As a result, the txlock must not guard
against interrupt context, and the spin_lock_irqsave()
from xmit can be replaced by spin_lock_bh(). Likewise,
the locking has been downgraded for clean_tx_ring().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII-ID uses an internal delay within the transmitter or receiver. This
feature is phy specific. The rest of the communication is normal RGMII.
So the fec driver has to check for all RGMII modes, not only
'PHY_INTERFACE_MODE_RGMII'.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device features a 64 bit nanoseconds register, and so with this
patch the driver is ready for the year 2038.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's clock is implemented using a timecounter, and so with
this patch the driver is ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC modules used on i.MX28 and newer have a register to tune the MDIO
output hold time that should be at least 10 ns. Up to now this value was not
explicitly set and so resulted in less hold time if the fec clock was
faster than 100 MHz.
This was noticed on an i.MX28 machine that uses an input clock of ~150
Mhz which resulted in unreliable communication with a Marvell switch.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ucc_geth was indicating link up after a port is administratively enabled even
when nothing is plugged in. This causes user-space tools to see a spurious link
up the first time after boot.
Signed-off-by: Cliff Clark <cliff_clark@selinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej S. Szmigiero