Comments in linux/spi/spi.h and observed behavior show that .setup()
callback can be called multiple times without corresponding calls to
.cleanup(), what was incorrectly assumed by spi-s3c64xx driver, leading
to failures trying to request CS GPIO multiple times.
This patch modifies the behavior of spi-s3c64xx driver to request CS
GPIO only on first call to .setup() after last .cleanup().
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Not all fields of dma_slave_config struct are being initialized by
prepare_dma() function, leaving those which are not in undefined state,
which can confuse DMA drivers using them.
This patch adds call to memset() to zero the struct before initializing
a subset of its fields.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that the bitbang core does not require a setup() function we can
drop the check in the altera, nuc900 and xilinx drivers.
Signed-off-by: Mark Brown <broonie@linaro.org>
It's perfectly valid not to have a setup callback when the probe routine
does all the needed things. So don't even check for this case and trust
the caller.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The bits_per_word variable is not used after commit 24778be20f
"spi: convert drivers to use bits_per_word_mask".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that DMA support has been added to the driver it needs the
architecture DMA driver to be built in order to link.
Signed-off-by: Mark Brown <broonie@linaro.org>
this patch enables DMA support for SiRFSoC SPI driver, if both
buffers and length are aligned with DMA controller's hardware
limitation, use generic SiRF generic dmaengine driver.
for PIO, SiRF SPI controller actually is using rx to trigger rx,
that means if we write any word to tx fifo, we will get a word
from rx fifo. for DMA, we use two different channel for tx and
rx, and issue them both for every transfer.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pass master to platform_set_drvdata() then we can remove my_master pointer.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have a SPI_BPW_MASK macro defined in spi.h, use it instead of open-coded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Don't rely on shdma dhaengine driver getting DMA slave addresses from its
slave configuration. Instead provide those addresses, using a
dmaengine_slave_config() call.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the following sparse warning by changing the
the format specifier for size_t to %zu.
drivers/spi/spi-ep93xx.c:512:3: warning:
format ‘%d’ expects argument of type ‘int’,
but argument 3 has type ‘size_t’ [-Wformat]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the following sparse warnings.
dma_addr_t can be either u32 or u64 so we should cast to the
largest type and use the format specifier %llx.
drivers/spi/spi-atmel.c: In function ‘atmel_spi_next_xfer_dma_submit’:
drivers/spi/spi-atmel.c:631:2: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 7 has type ‘dma_addr_t’ [-Wformat]
drivers/spi/spi-atmel.c:631:2: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 9 has type ‘dma_addr_t’ [-Wformat]
drivers/spi/spi-atmel.c: In function ‘atmel_spi_pdc_next_xfer’:
drivers/spi/spi-atmel.c:734:3: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 7 has type ‘dma_addr_t’ [-Wformat]
drivers/spi/spi-atmel.c:734:3: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 9 has type ‘dma_addr_t’ [-Wformat]
drivers/spi/spi-atmel.c:773:3: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 7 has type ‘dma_addr_t’ [-Wformat]
drivers/spi/spi-atmel.c:773:3: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 9 has type ‘dma_addr_t’ [-Wformat]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 048177ce3b (spi: spi-davinci:
convert to DMA engine API) introduced a regression: dma_map_single()
is called with direction DMA_FROM_DEVICE for rx and for tx.
Signed-off-by: Christian Eggers <ceggers@gmx.de>
Acked-by: Matt Porter <mporter@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org # v3.7.x+
Most SPI drivers that implement runtime PM support use identical code to
do so: they acquire a runtime PM lock in prepare_transfer_hardware() and
then they release it in unprepare_transfer_hardware(). The variations in
this are mostly missing error checking and the choice to use autosuspend.
Since these runtime PM calls are normally the only thing in the prepare
and unprepare callbacks and the autosuspend API transparently does the
right thing on devices with autosuspend disabled factor all of this out
into the core with a flag to enable the behaviour.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Currently the tegra slink driver acquires a runtime PM reference for the
duration of each transfer. This may result in the IP being powered down
between transfers which would be at best wasteful. Instead it is better
to do this in the callbacks that are generated before and after starting
a series of transfers, keeping the IP powered throughout.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Currently the tegra sflash driver acquires a runtime PM reference for the
duration of each transfer. This may result in the IP being powered down
between transfers which would be at best wasteful. Instead it is better
to do this in the callbacks that are generated before and after starting
a series of transfers, keeping the IP powered throughout.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Currently the tegra114 driver acquires a runtime PM reference for the
duration of each transfer. This may result in the IP being powered down
between transfers which would be at best wasteful. Instead it is better
to do this in the callbacks that are generated before and after starting
a series of transfers, keeping the IP powered throughout.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Enable auto loading by udev when spi-imx is compiled as a module.
Signed-off-by: Niels de Vos <ndevos@redhat.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable the build of drivers which don't have any real build time
dependency on their architecture or platform with COMPILE_TEST,
providing better build time coverage.
Signed-off-by: Mark Brown <broonie@linaro.org>
Previously the runtime PM API insisted on having callbacks for everything
but this requirement was removed a while ago so the empty callbacks can
also be removed.
Signed-off-by: Mark Brown <broonie@linaro.org>
Keystone2 SOCs share the SPI IP block with DaVinci based SOCs. Update
the config bits so that its usable on Keystone2 based SOCs.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
sdd->ops->request is unsigned int, not unsigned long.
Also, sdd->rx_dma.ch is a 'struct dma_chan *'.
Thus, (void *) is converted to (struct dma_chan *)(unsigned long),
in order to fix possible sparse warnings.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following build warnings when LPAE is enabled:
drivers/spi/spi-s3c64xx.c:1466:2: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type
'resource_size_t' [-Wformat]
drivers/spi/spi-s3c64xx.c:1466:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type
'resource_size_t' [-Wformat]
Use vsprintf extension %pR to format resource.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch error and warnings:
ERROR: "(foo*)" should be "(foo *)"
WARNING: line over 80 characters
WARNING: quoted string split across lines
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since the driver has been converted to use the core message pump code
the only use of the messsage queue in the driver is a check to see if
it is empty which will always succeed since nothing ever adds to the
queue. Just remove the queue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
As devm_ioremap_resource() is used on probe, there is no need to explicitly
check the return value from platform_get_resource(), as this is something that
devm_ioremap_resource() takes care by itself.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make spi core calculate the message length while
populating the other transfer parameters.
Usecase, driver can use it to populate framelength filed in their
controller.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 2025172e3 (spi/bitbang: Use core message pump), the following
kernel crash is seen:
Unable to handle kernel NULL pointer dereference at virtual address 0000000d
pgd = 80004000
[0000000d] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 48 Comm: spi32766 Not tainted 3.11.0-rc1+ #4
task: bfa3e580 ti: bfb90000 task.ti: bfb90000
PC is at spi_bitbang_transfer_one+0x50/0x248
LR is at spi_bitbang_transfer_one+0x20/0x248
...
,and also the following build warning:
drivers/spi/spi-bitbang.c: In function 'spi_bitbang_start':
drivers/spi/spi-bitbang.c:436:31: warning: assignment from incompatible pointer type [enabled by default]
In order to fix it, we need to change the first parameter of
spi_bitbang_transfer_one() to 'struct spi_master *master'.
Tested on a mx6qsabrelite by succesfully probing a SPI NOR flash.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In xilinx_spi_probe() we use xspi->irq to store negative error codes so
it has to be signed. We weren't going to use the upper bit any way so
this is fine.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert drivers using bitbang to use the core mesasge pump infrastructure,
saving some code and meaning that these drivers get to take advantage of
work done on improving the core implementation.
Signed-off-by: Mark Brown <broonie@linaro.org>
The SPI core provides infrastructure for standard message queueing. Use
that instead of handling it in the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_request_irq() for irq allocation which
simplify driver code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_ioremap_resource() automatically checks that
struct resource is initialized.
Also group platform_get_resource() and devm_ioremap_resource()
together.
And remove mem resource from struct xilinx_spi.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a more traditional name and makes things a bit clearer when
referring to actual struct devices as we do frequently during probe().
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
In the past there used to be a separate platform device type for device
tree systems so the probe and removal functions were split into generic
and bus sections. Since this is no longer the case simplify the code (and
remove some unprototyped exports) by factoring everything into the bus
probe() and remove().
Signed-off-by: Mark Brown <broonie@linaro.org>
We have nice specifier in kernel for that.
It changes separator from ',' (comma) to space, though it's not a big deal
since it's just a debug message.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Missing this will cause some user cases fail when they want to change spi
transfer mode.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Due to changes in mainline prior to submission the spi device detection
in polling mode breaks. This revealed the missing check for polling
during dma prepare. This patch adds the missing check.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is an additional bit in the Intel LPSS SPI private registers that
needs to be set in order to be able to use DMA with the SPI controller.
Enable this as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
stmp_reset_block() may fail, so let's check its return value and propagate it in
the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
While at it, rename 'out_free_dma' to 'out_disable_clk' so that it can properly
describe its purpose.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
On mxs_spi_probe() the dma channels are requested prior to enabling the SSP
clock, so in the error path we should disable the SSP clock first and
release the DMA channels later.
Same logic applies in mxs_spi_remove().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
While at it, fix the order of clk_disable_unprepare calls: clk_ipg should be
disabled first, followed by clk_per.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Using devm functions can make the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The divider values stored in the per chip data are only used to set the
registers in the hardware to generate the desired SPI clock. Since these
are calculated per transfer based on the t->speed_hz there is no reason
keep them in the per chip data.
Move the ep93xx_spi_calc_divisors() call into ep93xx_spi_chip_setup()
and return the dividers thru pointers. Remove the divider values from
the per chip data structure.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
The divisors needed to generate the SPI clock are calculated per
transfer based on the t->speed_hz. There is no reason to calculate
them in ep93xx_spi_setup().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_clk_get() so that the clk_put() happens automatically when
the last reference to this driver is dropped.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
This value is only needed to set the bits per word for each transfer
of a message. There is no reason to set the value in ep93xx_spi_enable()
because ep93xx_spi_process_transfer() sets it again for each transfer.
Just pass the t->bits_per_word directly to ep93xx_spi_chip_setup() in
ep93xx_spi_process_transfer() and remove 'dss' from the per chip private
data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
The kzalloc() failure will have already output a message.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
Get the platform resources early in the (*probe) to minimize the number
of goto's in the error path.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
Check t->bits_per_word directly and remove the inline helper function.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
The memory resource used by this driver is ioremap()'d and the normal
read,write calls can be used instead of the __raw_* variants.
Also, remove the inline tag on the helper functions and let the compiler
decide if they are inlined.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
__spi_async(), which starts every SPI message transfer, initializes
the bits_per_word and max speed for every transfer in the message.
Since the conditional test in ep93xx_spi_process_transfer() will
always succeed just remove it and always call ep93xx_spi_chip_setup()
to configure the hardware for each transfer in the message.
Remove the redundant ep93xx_spi_chp_setup() in ep93xx_spi_process_transfer()
which just initializes the hardware to the "default" based on the SPI
device.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
Allow drivers to avoid implementing their own checks for simple rates by
specifying the limits in the master structure.
Signed-off-by: Mark Brown <broonie@linaro.org>
The filter function used by the rspi driver is part of the DMAE controller
driver so if the DMA controller driver is somehow disabled then the rspi
driver will fail to build.
Signed-off-by: Mark Brown <broonie@linaro.org>
New spi controller(version 3) is integrated into Blackfin
60x processor. Comparing to bf5xx spi controller, we support
32 bits word size and independent receive and transmit DMA
channels now. Also mode 0 and 2 (CPHA = 0) can get fully
supported becasue cs line may be controlled by the software.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to make it easier to convert to transfer_one_message() lift the
code that does the actual message transfer out of the work function that
implements the message pump. This should have no functional impact, it's
just a simple code motion patch.
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently no drivers use the ability to override spi_bitbang_transfer()
and if any started this would make it harder to convert the bitbang code
to use transfer_one_message() so remove the export in order to prevent
anyone starting.
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Commit 24778be "spi: convert drivers to use bits_per_word_mask" removed
what appeared to be redundant code from many drivers. However, it
appears that in the spi-bitbang case, these functions are required by
the spi-bitbang core, even if they don't do anything. Restore them.
For 3.12, the spi-bitbang core should be adjusted not to require these
callbacks to exist if they don't need to do anything.
This is the equivalent of Michal Simek's patch "spi/xilinx: Revert
master->setup function removal", applied to other affected drivers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
master->setup() must be initialized to be able
to successfully run spi_bitbang_start()
and satisfy if/else logic there.
"spi: convert drivers to use bits_per_word_mask"
(sha1: 24778be20f)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merge first patch-bomb from Andrew Morton:
- various misc bits
- I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
distracted. There has been quite a bit of activity.
- About half the MM queue
- Some backlight bits
- Various lib/ updates
- checkpatch updates
- zillions more little rtc patches
- ptrace
- signals
- exec
- procfs
- rapidio
- nbd
- aoe
- pps
- memstick
- tools/testing/selftests updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
tools/testing/selftests: don't assume the x bit is set on scripts
selftests: add .gitignore for kcmp
selftests: fix clean target in kcmp Makefile
selftests: add .gitignore for vm
selftests: add hugetlbfstest
self-test: fix make clean
selftests: exit 1 on failure
kernel/resource.c: remove the unneeded assignment in function __find_resource
aio: fix wrong comment in aio_complete()
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
drivers/memstick/host/r592.c: convert to module_pci_driver
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
pps-gpio: add device-tree binding and support
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
drivers/parport/share.c: use kzalloc
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
aoe: update internal version number to v83
aoe: update copyright date
aoe: perform I/O completions in parallel
...
Calling kthread_run with a single name parameter causes it to be handled
as a format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Hotplug changes allowing device hot-removal operations to fail
gracefully (instead of crashing the kernel) if they cannot be
carried out completely. From Rafael J Wysocki and Toshi Kani.
- Freezer update from Colin Cross and Mandeep Singh Baines targeted
at making the freezing of tasks a bit less heavy weight operation.
- cpufreq resume fix from Srivatsa S Bhat for a regression introduced
during the 3.10 cycle causing some cpufreq sysfs attributes to
return wrong values to user space after resume.
- New freqdomain_cpus sysfs attribute for the acpi-cpufreq driver to
provide information previously available via related_cpus from
Lan Tianyu.
- cpufreq fixes and cleanups from Viresh Kumar, Jacob Shin,
Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia, Arnd Bergmann, and
Tang Yuantian.
- Fix for an ACPICA regression causing suspend/resume issues to
appear on some systems introduced during the 3.4 development cycle
from Lv Zheng.
- ACPICA fixes and cleanups from Bob Moore, Tomasz Nowicki, Lv Zheng,
Chao Guan, and Zhang Rui.
- New cupidle driver for Xilinx Zynq processors from Michal Simek.
- cpuidle fixes and cleanups from Daniel Lezcano.
- Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk.
- ACPI device power management fixes and cleanups from Fengguang Wu
and Rafael J Wysocki.
- ACPI documentation updates from Lv Zheng, Aaron Lu and Hanjun Guo.
- Fix for the IA-64 issue that was the reason for reverting commit
9f29ab1 and updates of the ACPI scan code from Rafael J Wysocki.
- Mechanism for adding CMOS RTC address space handlers from Lan Tianyu
(to allow some EC-related breakage to be fixed on some systems).
- Spec-compliant implementation of acpi_os_get_timer() from
Mika Westerberg.
- Modification of do_acpi_find_child() to execute _STA in order to
to avoid situations in which a pointer to a disabled device object
is returned instead of an enabled one with the same _ADR value.
From Jeff Wu.
- Intel BayTrail PCH (Platform Controller Hub) support for the ACPI
Intel Low-Power Subsystems (LPSS) driver and modificaions of that
driver to work around a couple of known BIOS issues from
Mika Westerberg and Heikki Krogerus.
- EC driver fix from Vasiliy Kulikov to make it use get_user() and
put_user() instead of dereferencing user space pointers blindly.
- Assorted ACPI code cleanups from Bjorn Helgaas, Nicholas Mazzuca and
Toshi Kani.
- Modification of the "runtime idle" helper routine to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows some code bloat
reduction to be done, from Rafael J Wysocki and Alan Stern.
- New trace points for PM QoS from Sahara <keun-o.park@windriver.com>.
- PM QoS documentation update from Lan Tianyu.
- Assorted core PM code cleanups and changes from Bernie Thompson,
Bjorn Helgaas, Julius Werner, and Shuah Khan.
- New devfreq driver for the Exynos5-bus device from Abhilash Kesavan.
- Minor devfreq cleanups, fixes and MAINTAINERS update from
MyungJoo Ham, Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and
Wei Yongjun.
- OMAP Adaptive Voltage Scaling (AVS) SmartReflex voltage control
driver updates from Andrii Tseglytskyi and Nishanth Menon.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=VBBq
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the total number of ACPI commits is slightly greater than
the number of cpufreq commits, but Viresh Kumar (who works on cpufreq)
remains the most active patch submitter.
To me, the most significant change is the addition of offline/online
device operations to the driver core (with the Greg's blessing) and
the related modifications of the ACPI core hotplug code. Next are the
freezer updates from Colin Cross that should make the freezing of
tasks a bit less heavy weight.
We also have a couple of regression fixes, a number of fixes for
issues that have not been identified as regressions, two new drivers
and a bunch of cleanups all over.
Highlights:
- Hotplug changes to support graceful hot-removal failures.
It sometimes is necessary to fail device hot-removal operations
gracefully if they cannot be carried out completely. For example,
if memory from a memory module being hot-removed has been allocated
for the kernel's own use and cannot be moved elsewhere, it's
desirable to fail the hot-removal operation in a graceful way
rather than to crash the kernel, but currenty a success or a kernel
crash are the only possible outcomes of an attempted memory
hot-removal. Needless to say, that is not a very attractive
alternative and it had to be addressed.
However, in order to make it work for memory, I first had to make
it work for CPUs and for this purpose I needed to modify the ACPI
processor driver. It's been split into two parts, a resident one
handling the low-level initialization/cleanup and a modular one
playing the actual driver's role (but it binds to the CPU system
device objects rather than to the ACPI device objects representing
processors). That's been sort of like a live brain surgery on a
patient who's riding a bike.
So this is a little scary, but since we found and fixed a couple of
regressions it caused to happen during the early linux-next testing
(a month ago), nobody has complained.
As a bonus we remove some duplicated ACPI hotplug code, because the
ACPI-based CPU hotplug is now going to use the common ACPI hotplug
code.
- Lighter weight freezing of tasks.
These changes from Colin Cross and Mandeep Singh Baines are
targeted at making the freezing of tasks a bit less heavy weight
operation. They reduce the number of tasks woken up every time
during the freezing, by using the observation that the freezer
simply doesn't need to wake up some of them and wait for them all
to call refrigerator(). The time needed for the freezer to decide
to report a failure is reduced too.
Also reintroduced is the check causing a lockdep warining to
trigger when try_to_freeze() is called with locks held (which is
generally unsafe and shouldn't happen).
- cpufreq updates
First off, a commit from Srivatsa S Bhat fixes a resume regression
introduced during the 3.10 cycle causing some cpufreq sysfs
attributes to return wrong values to user space after resume. The
fix is kind of fresh, but also it's pretty obvious once Srivatsa
has identified the root cause.
Second, we have a new freqdomain_cpus sysfs attribute for the
acpi-cpufreq driver to provide information previously available via
related_cpus. From Lan Tianyu.
Finally, we fix a number of issues, mostly related to the
CPUFREQ_POSTCHANGE notifier and cpufreq Kconfig options and clean
up some code. The majority of changes from Viresh Kumar with bits
from Jacob Shin, Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia,
Arnd Bergmann, and Tang Yuantian.
- ACPICA update
A usual bunch of updates from the ACPICA upstream.
During the 3.4 cycle we introduced support for ACPI 5 extended
sleep registers, but they are only supposed to be used if the
HW-reduced mode bit is set in the FADT flags and the code attempted
to use them without checking that bit. That caused suspend/resume
regressions to happen on some systems. Fix from Lv Zheng causes
those registers to be used only if the HW-reduced mode bit is set.
Apart from this some other ACPICA bugs are fixed and code cleanups
are made by Bob Moore, Tomasz Nowicki, Lv Zheng, Chao Guan, and
Zhang Rui.
- cpuidle updates
New driver for Xilinx Zynq processors is added by Michal Simek.
Multidriver support simplification, addition of some missing
kerneldoc comments and Kconfig-related fixes come from Daniel
Lezcano.
- ACPI power management updates
Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk, sparse warning fix from Fengguang Wu and
cleanups and fixes of the ACPI device power state selection
routine.
- ACPI documentation updates
Some previously missing pieces of ACPI documentation are added by
Lv Zheng and Aaron Lu (hopefully, that will help people to
uderstand how the ACPI subsystem works) and one outdated doc is
updated by Hanjun Guo.
- Assorted ACPI updates
We finally nailed down the IA-64 issue that was the reason for
reverting commit 9f29ab11dd ("ACPI / scan: do not match drivers
against objects having scan handlers"), so we can fix it and move
the ACPI scan handler check added to the ACPI video driver back to
the core.
A mechanism for adding CMOS RTC address space handlers is
introduced by Lan Tianyu to allow some EC-related breakage to be
fixed on some systems.
A spec-compliant implementation of acpi_os_get_timer() is added by
Mika Westerberg.
The evaluation of _STA is added to do_acpi_find_child() to avoid
situations in which a pointer to a disabled device object is
returned instead of an enabled one with the same _ADR value. From
Jeff Wu.
Intel BayTrail PCH (Platform Controller Hub) support is added to
the ACPI driver for Intel Low-Power Subsystems (LPSS) and that
driver is modified to work around a couple of known BIOS issues.
Changes from Mika Westerberg and Heikki Krogerus.
The EC driver is fixed by Vasiliy Kulikov to use get_user() and
put_user() instead of dereferencing user space pointers blindly.
Code cleanups are made by Bjorn Helgaas, Nicholas Mazzuca and Toshi
Kani.
- Assorted power management updates
The "runtime idle" helper routine is changed to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows us to reduce the
overall code bloat a bit (by dropping some code that's not
necessary any more after that modification).
The runtime PM documentation is updated by Alan Stern (to reflect
the "runtime idle" behavior change).
New trace points for PM QoS are added by Sahara
(<keun-o.park@windriver.com>).
PM QoS documentation is updated by Lan Tianyu.
Code cleanups are made and minor issues are addressed by Bernie
Thompson, Bjorn Helgaas, Julius Werner, and Shuah Khan.
- devfreq updates
New driver for the Exynos5-bus device from Abhilash Kesavan.
Minor cleanups, fixes and MAINTAINERS update from MyungJoo Ham,
Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and Wei Yongjun.
- OMAP power management updates
Adaptive Voltage Scaling (AVS) SmartReflex voltage control driver
updates from Andrii Tseglytskyi and Nishanth Menon."
* tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
cpufreq: Fix cpufreq regression after suspend/resume
ACPI / PM: Fix possible NULL pointer deref in acpi_pm_device_sleep_state()
PM / Sleep: Warn about system time after resume with pm_trace
cpufreq: don't leave stale policy pointer in cdbs->cur_policy
acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
cpufreq: make sure frequency transitions are serialized
ACPI: implement acpi_os_get_timer() according the spec
ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
ACPI: Add CMOS RTC Operation Region handler support
ACPI / processor: Drop unused variable from processor_perflib.c
cpufreq: tegra: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: s3c64xx: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: omap: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: imx6q: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: exynos: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: dbx500: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: davinci: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: arm-big-little: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
...
A fairly quiet release for the SPI subsystem, the standout changes
being:
- Core support for implementing bits per word constraints implemented by
Stephen Warren, factoring some code out of drivers.
- Addition of polling mode support for the s3c64xx driver as some newer
Exynos systems have taken the unusual step of removing interrupt
support.
- Use of the in-IP FIFO and generic dmaengine support for the OMAP2
driver, providing improved performance.
- Conversion of the mpc512x driver to use the core message queue
infrastructure.
The nicest thing being that all the factoring out into common code leads
to a negative diffstat overall.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/2eV
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for the SPI subsystem, the standout changes
being:
- Core support for implementing bits per word constraints implemented
by Stephen Warren, factoring some code out of drivers.
- Addition of polling mode support for the s3c64xx driver as some
newer Exynos systems have taken the unusual step of removing
interrupt support.
- Use of the in-IP FIFO and generic dmaengine support for the OMAP2
driver, providing improved performance.
- Conversion of the mpc512x driver to use the core message queue
infrastructure.
The nicest thing being that all the factoring out into common code
leads to a negative diffstat overall."
* tag 'spi-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (42 commits)
spi/s3c64xx: Rely on the compiler eliminating the OF ID table
spi: s3c64xx: Added support for exynos5440 spi
spi: s3c64xx: Added provision for dedicated cs pin
spi: omap2-mcspi: add generic DMA request support to the DT binding
spi: omap2-mcspi: convert to dma_request_slave_channel_compat()
spi/s3c64xx: Make wait_for_timeout() function name less generic
spi: s3c64xx: added support for polling mode
spi: omap2-mcspi: Add FIFO buffer support
spi: omap2-mcspi: Move bytes per word calculation to the function
spi: spi-xilinx: cleanup a check in xilinx_spi_txrx_bufs()
spi: spi-nuc900: Remove redundant platform_set_drvdata()
spi: spi-fsl-lib: Make mpc8xxx_spi_work static
spi: spi-topcliff-pch: Fix sparse warnings
spi: spi-xilinx: Remove redundant platform_set_drvdata()
spi: spi-xilinx: Add run run-time endian detection
spi: mpc512x: use the SPI subsystem's message queue
spi: mpc512x: improve throughput in the RX/TX func
spi: mpc512x: minor prep before feature change
spi: atmel: convert to dma_request_slave_channel_compat()
spi: sirf: avoid uninitialized-use warning
...
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJR0Z07AAoJEEEQszewGV1zx+oP/j+bh39e1Fc8ySFNvpwLFFRb
EbQZx21XsK+d4fUVYQJ1IBh3e5FTqkmvHarbO1aNttqyk7eN5P4EFb3dLExIX+81
6SJYtldH5ZdvLpJNvSXAX6fUjTD1CtBCDs5z5AvDQjqUArQ2tKlzJJgFXW8MSd3B
5hd7XdU5g30GbVzFwrPbVUZwRM12YVs/HACkP6uFqDjB8KX6nXpETlqeeFW+ApvW
RPT7iN/CsFls7gl6mHsPvScdfXar0ilZfu0hTf3EmhlVK1/iPOV6aqAF9z4j2Yxf
ICL/x3phJ0Q7yNeZslif0KN3iJnrRGbdNvBi6wim35Ds5Uf3lY2SAhSvxNmkjT8n
DB9oBTvQzr5OEv8fstWJAT+BWIdZ6Z91IqJ5Gy40A91oVUU9NDDBR3ur2gIneEUz
51kOUhucCzpiht5A/7djAx6MYYOEUwjGNzjOs7tGcxCxz4+Rb2DbAXZ3Cew45ddh
1QsfL3588A0DTp7ccw7f4QwYveX/cquzia/MD8AtdrUSYFEPfkexEo540/VqMl8j
aMJ8Uuca9GSnyXDk+ziwkzLg2DjTw+p+6IygNr2GLrXFH2LTAKRpz/SidyLArDsw
0sTFan0sdU3497rHX5Xc8yCyDY4sXCdQm3/er+TE+Z7V2dS99GuEysCAInIdvM1I
Wupqaxw4A25YSmbRFVpR
=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
These are various bug fixes that were not considered important enough
for merging into 3.10. The majority of the ARM fixes are for the OMAP
and at91 platforms, and there is another set of bug fixes for device
drivers that resolve 'randconfig' build errors and that the subsystem
maintainers either did not pick up or preferred to get merged through
the arm-soc tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gNDf
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-cricitical bug fixes from Arnd Bergmann:
"These are various bug fixes that were not considered important enough
for merging into 3.10.
The majority of the ARM fixes are for the OMAP and at91 platforms, and
there is another set of bug fixes for device drivers that resolve
'randconfig' build errors and that the subsystem maintainers either
did not pick up or preferred to get merged through the arm-soc tree."
* tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: at91/PMC: use at91_usb_rate() for UTMI PLL
ARM: at91/PMC: fix at91sam9n12 USB FS init
ARM: at91/PMC: at91sam9n12 family has a PLLB
ARM: at91/PMC: sama5d3 family doesn't have a PLLB
ARM: tegra: fix section mismatch in tegra_pmc_parse_dt
ARM: mxs: don't select HAVE_PWM
ARM: mxs: stub out mxs_pm_init for !CONFIG_PM
cpuidle: calxeda: select ARM_CPU_SUSPEND
ARM: mvebu: fix length of ethernet registers in mv78260 dtsi
ARM: at91: cpuidle: Fix target_residency
ARM: at91: fix at91_extern_irq usage for non-dt boards
ARM: sirf: use CONFIG_SIRF rather than CONFIG_PRIMA2 where necessary
clocksource: kona: adapt to CLOCKSOURCE_OF_DECLARE change
X.509: do not emit any informational output
mtd: omap2: allow bulding as a module
[SCSI] nsp32: use mdelay instead of large udelay constants
hwrng: bcm2835: fix MODULE_LICENSE tag
ARM: at91: Change the internal SRAM memory type MT_MEMORY_NONCACHED
ARM: at91: Fix link breakage when !CONFIG_PHYLIB
MAINTAINERS: Add exynos filename match to ARM/S5P EXYNOS ARM ARCHITECTURES
...
After the patch "spi/s3c64xx: Fix non-dmaengine usage"
with commit id 563b444e33
submitted by Mark Brown, the spi device detection in polling
mode breaks. This revealed the missing check for polling during
dma prepare. This patch adds the missing check.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This should work with modern compilers, isn't that much of an issue if
it goes wrong and it ensures that the DT-only hardware variants don't
leave unreferenced parameters structures lying around.
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the exynos5440 spi controller.
The integration of the spi IP in exynos5440 is different from
other SoC's. The I/O pins are no more configured via gpio, they
have dedicated pins.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The existing driver supports gpio based /cs signal.
For controller's that have one device per controller,
the slave device's /cs signal might be internally controlled
by the chip select bit of slave select register. They are not
externally asserted/deasserted using gpio pin.
This patch adds support for controllers with dedicated /cs pin.
if "cs-gpio" property doesnt exist in a spi dts node, the controller
would treat the /cs pin as dedicated.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert dmaengine channel requests to use
dma_request_slave_channel_compat(). This supports the DT case of
platforms requiring channel selection from either the OMAP DMA or
the EDMA engine. AM33xx only boots from DT and is the only user
implementing EDMA so in the !DT case we can default to the OMAP DMA
filter.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRvsJmAAoJEFBXWFqHsHzOHOIH/jjVCaAFdOskPI4d9qPPAt9C
5o0aJDjerzTm+vH2mbec2507fChaYrLybAypJUj6wDYRf03RhAgPXorY83Y+3WtG
SYz2UWza7MY8GeZv6e9tdrYS3JUSicFXPf8MsOcINsuyIub3dD96z36OqrnWZLFy
uH5V81e4gOHECd4PWIxmhdjwawqmwb/Pqzl0V3+vXi2JM07xrn7/SqlZ7VfUwM2q
DNhu5ugH7FtaFp75YrmTIhp6i+tovguRr0RIt6dnk/9gbJBQnV2Cw2MzdRPT12U5
bC79P7sojkKRtITcq9c1fnUNhkgc0+hS8HoezcQmzKMin6nFmVAh5wQFSlRJMJE=
=mZw+
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
imx soc changes for 3.11:
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
* tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (29 commits)
ARM: imx_v6_v7_defconfig: Enable Vybrid VF610
ARM: imx_v6_v7_defconfig: Enable imx-wm8962 by default
ARM: clk-imx6qdl: Add clko1 configuration for imx6qdl-sabresd
ARM: imx_v6_v7_defconfig: Enable PWM and backlight options
ARM: imx: Remove mxc specific ulpi access ops
ARM: imx: add initial support for VF610
ARM: imx: add VF610 clock support
ARM: imx_v6_v7_defconfig: enable parallel display
ARM: imx: clk: No need to initialize phandle struct
ARM: imx: irq-common: Include header to avoid sparse warning
ARM: imx: Enable mx6 solo-lite support
ARM: imx6: use common of_clk_init() call to initialize clocks
ARM: imx6q: call of_clk_init() to register fixed rate clocks
ARM: imx: imx_v6_v7_defconfig: Select CONFIG_DRM_IMX_TVE
ARM: i.MX6: clk: add different DualLite MLB clock config
ARM i.MX5: Add S/PDIF clocks
ARM i.MX53: Add SATA clock
ARM: imx6q: clk: add the eim_slow clock
ARM: imx: remove MLB PLL from pllv3
ARM: imx: disable pll8_mlb in mx6q_clks
...
Conflicts:
arch/arm/Kconfig.debug (simple add/add conflict)
Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=fstd
-----END PGP SIGNATURE-----
Merge tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/soc
From Linus Walleij:
Device Tree and Multiplatform support for U300:
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
* tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (40 commits)
ARM: u300: switch to using syscon regmap for board
ARM: u300: Update MMC configs for u300 defconfig
spi: pl022: use DMA by default when probing from DT
pinctrl: get rid of all platform data for coh901
ARM: u300: convert MMC/SD clock to device tree
ARM: u300: move the gated system controller clocks to DT
i2c: stu300: do not request a specific clock name
clk: move the U300 fixed and fixed-factor to DT
ARM: u300: remove register definition file
ARM: u300: add syscon node
ARM: u300 use module_spi_driver to register driver
ARM: u300: delete remnant machine headers
ARM: u300: convert to multiplatform
ARM: u300: localize <mach/u300-regs.h>
ARM: u300: delete <mach/irqs.h>
ARM: u300: delete <mach/hardware.h>
ARM: u300: push down syscon registers
ARM: u300: remove deps from debug macro
ARM: u300: move debugmacro to debug includes
ARM: u300: delete all static board data
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I got a build error today that made me realize that it is not
possible to build a kernel for a SiRF platform without enabling
CONFIG_PRIMA2, since a lot of common code depends on CONFIG_PRIMA2.
This fixes all occurences that appear like common SiRF code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
The 64xx spi driver supports partial polling mode.
Only the last chunk of the transfer length is transferred
or recieved in polling mode.
Some SoC's that adopt this controller might not have have dma
interface. This patch adds support for complete polling mode
and gives flexibity for the user to select poll/dma mode.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
pxa2xx_spi_map_dma_buffer() gets called in tasklet context so we can't
sleep when we allocate a new sg table. Use GFP_ATOMIC here instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The MCSPI controller has a built-in FIFO buffer to unload the DMA or interrupt
handler and improve data throughput. This patch adds FIFO buffer support for SPI
transfers in DMA mode.
For SPI transfers in DMA mode, the largest possible FIFO buffer size will be
calculated and set up. The FIFO won't be used for the SPI transfers in DMA mode
if: calculated FIFO buffer size is less then 2 bytes or the FIFO buffer size
isn't multiple of the SPI word length.
Signed-off-by: Illia Smyrnov <illia.smyrnov@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the past we controlled the selection of DMA for a certain
host by a boolean switch in the platform data. Currently
there is no way to enable DMA on a PL022 probed from the
device tree. Let's default to trying to obtain DMA channels
in the DT case, and then we can always fail (and thus fall
back to PIO mode).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce mcspi_bytes_per_word function as replacement for the next code
fragment:
int c = (word_len <= 8) ? 1 :
(word_len <= 16) ? 2 :
/* word_len <= 32 */ 4;
This code used 2 times in current driver code and will be used 2 times in
the next FIFO buffer support patch. Replace it with inline function with clear
name to improve code legibility.
Signed-off-by: Illia Smyrnov <illia.smyrnov@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This utilize the new pinctrl core PM helpers to transition
the driver to "sleep" and "idle" states, cutting away some
boilerplate code.
Cc: Hebbar Gururaja <gururaja.hebbar@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
Without this patch there are seen errors like:
[ 8.540000] s3c64xx-spi 13930000.spi: Failed to enable device: 1
[ 8.545000] spi_master spi1: failed to prepare transfer hardware
Likely because the driver uses synchronous API to runtime enable
the device and asynchronous one to disable it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonielinaro.org>
Cc: stable@vger.kernel.org
'!' has higher precedence than comparisons so the original condition
is equivalent to "if (xspi->remaining_bytes == 0)". This makes the
static checkers complain.
xspi->remaining_bytes is signed and from looking at the code
briefly, I think it might be able to go negative. I suspect that
going negative may cause a bug, but I don't have the hardware and
can't test.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Tomasz Figa