Add support for mmap'ed RX and TX ring setup and teardown based on the
af_packet.c code. The following patches will use this to add the real
mmap'ed receive and transmit functionality.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For mmap'ed I/O a netlink specific skb destructor needs to be invoked
after the final kfree_skb() to clean up state. This doesn't work currently
since the skb's ownership is transfered to the receiving socket using
skb_set_owner_r(), which orphans the skb, thereby invoking the destructor
prematurely.
Since netlink doesn't account skbs to the originating socket, there's no
need to orphan the skb. Add a netlink specific skb_set_owner_r() variant
that does not orphan the skb and use a netlink specific destructor to
call sock_rfree().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netlink doesn't account skbs to the sending socket, so the there's no
need to orphan the skb before trimming it.
Removing the skb_orphan() call is required for mmap'ed netlink, which uses
a netlink specific skb destructor that must not be invoked before the
final freeing of the skb.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to allocate a sk_buff head without any data. This will
be used by memory mapped netlink to attach data from the mmaped area
to the skb.
Additionally change skb_release_all() to check whether the skb has a
data area to allow the skb destructor to clear the data pointer in case
only a head has been allocated.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory mapped netlink needs to store the receiving userspace socket
when sending from the kernel to userspace. Rename 'ssk' to 'sk' to
avoid confusion.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy says:
====================
The following patches add support for 802.1ad (provider tagging) to the
VLAN driver. The patchset consists of the following parts:
- renaming of the NET_F_HW_VLAN feature flags to indicate that they only
operate on CTAGs
- preparation for 802.1ad VLAN filtering offload by adding a proto argument
to the rx_{add,kill}_vid net_device_ops callbacks
- preparation of the VLAN code to support multiple protocols by making the
protocol used for tagging a property of the VLAN device and converting
the device lookup functions accordingly
- second step of preparation of the VLAN code by making the packet tagging
functions take a protocol argument
- introducation of 802.1ad support in the VLAN code, consisting mainly of
checking for ETH_P_8021AD in a couple of places and testing the netdevice
offload feature checks to take the protocol into account
- announcement of STAG offloading capabilities in a couple of drivers for
virtual network devices
The patchset is based on net-next.git and has been tested with single and
double tagging with and without HW acceleration (for CTAGs).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- macvlan: propagate STAG filtering capabilities from underlying device
- ifb: announce STAG tagging support in addition to CTAG tagging support
- veth: announce STAG tagging/stripping support in addition to CTAG support
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 802.1ad VLAN devices. This mainly consists of checking for
ETH_P_8021AD in addition to ETH_P_8021Q in a couple of places and check
offloading capabilities based on the used protocol.
Configuration is done using "ip link":
# ip link add link eth0 eth0.1000 \
type vlan proto 802.1ad id 1000
# ip link add link eth0.1000 eth0.1000.1000 \
type vlan proto 802.1q id 1000
52:54:00:12:34:56 > 92:b1:54:28:e4:8c, ethertype 802.1Q (0x8100), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84)
20.1.0.2 > 20.1.0.1: ICMP echo request, id 3003, seq 8, length 64
92:b1:54:28:e4:8c > 52:54:00:12:34:56, ethertype 802.1Q-QinQ (0x88a8), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 47944, offset 0, flags [none], proto ICMP (1), length 84)
20.1.0.1 > 20.1.0.2: ICMP echo reply, id 3003, seq 8, length 64
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the encapsulation protocol value a property of VLAN devices and change
the device lookup functions to take the protocol value into account.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to ixgbe and igb.
The ixgbe changes contains 2 patches from the community, one which is a
fix from akepner to fix a issue where netif_running() in shutdown was
not done under rtnl_lock. The other community fix from Joe Perches
cleans up #ifdef CONFIG_DEBUG_FS which is no longer necessary. The
last ixgbe patch, from Jacob Keller, adds support for WoL on 82559
SFP+ LOM.
The remaining patches are against igb, 10 of which were previously
submitted in a pull request where changes were requested.
The following igb patches:
igb: Support for 100base-fx SFP
igb: Support to read and export SFF-8472/8079 data
are v2 based on feedback from Dan Carpenter and Ben Hutchings in
the previous pull request.
The largest set of changes are in my patch to cleanup code comments
and whitespace to align the igb driver with the networking style of
code comments. While cleaning up the code comments, fixed several
other whitespace/checkpatch.pl code formatting issues.
Other notable igb patches are EEE capable devices query the PHY to
determine what the link partner is advertising, added support for
i354 devices and added support for spoofchk config.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds base support for new i354 devices. Loopback test is
unsupported for this release.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for spoofchk configuration per VF via iproute2 tool.
Signed-off-by: Lior Levy <lior.levy@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On EEE-capable devices, query the PHY to determine what the link partner is
advertising.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Aligns the multi-line code comments with the desired style for the
networking tree. Also cleaned up whitespace issues found during the
cleanup of code comments (i.e. remove unnecessary blank lines,
use tabs where possible, properly wrap lines and keep strings on a
single line)
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
This patch fixes sparse warnings on function pointers that are not
defined as static.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It turns out that the InterruptThrottleRate module parameter was only
having the effect of locking the ITR at the starting ITR value. This was
because the values stored in rx_itr_setting and tx_itr_setting were being
ignored when configuring the initial itr_val of the q_vector.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We only need the adapter pointer in the case of ptp. As such we can pull the
adapter out of the main path and place it inside the if statement to avoid
the temptation of accessing the adapter pointer in the fast path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were incorrectly checking the entire frag_off field when we only wanted the
fragment offset. As a result we were not pulling in TCP headers when the DNF
flag was set.
To correct that we will now check for frag off using the IP_OFFSET mask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes code and comments as identified in the driver.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on original patch from Aurélien Guillaume <footplus@gmail.com>
This patch adds support to turn on I2C, with sfp cage powered.
CC: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support to read and export SFF-8472/8079 (SFP data)
over i2c, through Ethtool.
v2: Changed implementation to accommodate any offset within SFF module
length boundary.
Reported-by: Aurélien Guillaume <footplus@gmail.com>
CC: Aurélien Guillaume <footplus@gmail.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for 100base-fx SFP and report proper link speed/duplex
via Ethtool.
v2: fix smatch warnings
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add some empty static inlines instead to make
the code more readable.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds software support for WoL for the 82599 SFP+ LOM device,
(ID 0x8976)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
This series contains updates to ixgbe only.
v2- Dropped the following 2 patches from the series:
ixgbe: Support using build_skb in the case that jumbo frames are disabled
ixgbe: walk pci-e bus to find minimum width
Ben Hutchings found a bug with Alex's patch, so that patch was dropped
permanently. Jacob's "walk PCIe bus" patch is being re-worked for
a more generic solution so that other drivers can benefit.
In the remaining patches...
Alex provides a fix where we were incorrectly checking the entire frag_off
field when we only wanted the fragment offset. Alex also cleans up
the check for PAGE_SIZE, since the default configuration allocates 32K
for all buffers.
Emil provides a change to the calculation of eerd so that it is consistent
between the read and write functions by using | instead of +.
Jacob adds support for displaying PCIe Gen3 link speed, which was
previously missing from the ixgbe driver. He also provides a patch
to clean up ixgbe_get_bus_info_generic to call some conversion
functions, which are used also in another patch provided by Jacob.
Jacob modifies the driver to enable certain devices (which have an
internal switch) to read from the physical slot rather than reading
data from the internal switch.
Don provides a couple of fixes (which are more appropriate for net-next),
one of which resolves an issue where ixgbe was only turning on the laser
when the adapter was up which caused issues for those who wanted to
access the MNG firmware while the port was in a down state. The other
fix is for WoL when currently linked at 1G. Lastly Don bumps the driver
version keep the in-kernel driver up to date with the current functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Host queues (Qdisc + NIC) can hold packets so long that TCP can
eventually retransmit a packet before the first transmit even left
the host.
Its not clear right now if we could avoid this in the first place :
- We could arm RTO timer not at the time we enqueue packets, but
at the time we TX complete them (tcp_wfree())
- Cancel the sending of the new copy of the packet if prior one
is still in queue.
This patch adds instrumentation so that we can at least see how
often this problem happens.
TCPSpuriousRtxHostQueues SNMP counter is incremented every time
we detect the fast clone is not yet freed in tcp_transmit_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing in the driver that requires <asm/coldfire.h> and
<asm/mcfsim.h>.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump the version number reflect the corresponding functionality in the
out of tree driver.
Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We reset during the shutdown path which will reset AUTOC register. This
would change LMS to 10G. If we were currently linked at 1G we will lose
link, which is a bad thing if we wanted WoL to work. For the fix I needed
to know if WoL is supported so I created a new bool in the ixgbe_hw struct.
If this is set we will not allow the reset to change the current LMS value
in AUTOC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were only turning the laser on when the adapter was up. This
causes issues for those who wanted to access the MNG FW while the
port was in a down state. This patch makes sure the laser is turned
on in probe and remain up even after the port is brought down.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the driver to enable certain devices, which have an internal
switch, to read data from the physical slot rather than reading data from the
internal switch. The internal switch will always report the same PCI width and
speed, which is not useful compared to knowing the width and speed of the slot
the physical card is plugged into.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up ixgbe_get_bus_info_generic to call some conversion
functions, which are used also in a follow on patch that needs to convert
between the link_status PCIe config values into ixgbe's internal enum
representations.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for displaying PCIe Gen3 link speed, which was
previously missing from the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for PAGE_SIZE is pointless now that the default configuration is to
allocate 32K for all buffers. Since the Tx descriptor limit is 16K we can
just drop the check and always compare the descriptors to the maximum size
supported.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the calculation of eerd consistent between the read and write functions
by using | instead of + for IXGBE_EEPROM_RW_REG_START
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were incorrectly checking the entire frag_off field when we only wanted the
fragment offset. As a result we were not pulling in TCP headers when the DNF
flag was set.
To correct that we will now check for frag off using the IP_OFFSET mask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Patrick McHardy says:
====================
The following patchset adds support for running TIPC over InfiniBand.
The patchset consists of three parts (+ a minor fix for the ethernet media
type):
- Preparation: removal of an the unused str2addr callback and move of the
bcast_addr from struct tipc_media to struct tipc_bearer. This is necessary
because InfiniBand doesn't have a fixed broadcast address like ethernet,
so it needs to be initialized with the device's broadcast address when
the bearer is enabled
- Introduction of a TIPC InfiniBand media type. A new media type is needed
to deal with the different address sizes
- Support for ETH_P_TIPC in IPoIB
Since the last posting I've addressed all feedback I received and rebased
to the current net-next tree.
I consider these patches ready for merging. Since they mainly affect TIPC
code, I'd propose to have them either go through the TIPC tree or through
Dave directly (not sure how TIPC patches are managed).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support TIPC in the IPoIB driver. Since IPoIB now keeps track of its own
neighbour entries and doesn't require the packet to have a dst_entry
anymore, the only necessary changes are to:
- not drop multicast TIPC packets because of the unknown ethernet type
- handle unicast TIPC packets similar to IPv4/IPv6 unicast packets
in ipoib_start_xmit().
An alternative would be to remove all ethertype limitations since they're
not necessary anymore, all TIPC needs to know about is ARP and RARP since
it wants to always perform "path find", even if a path is already known.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add InfiniBand media type based on the ethernet media type.
The only real difference is that in case of InfiniBand, we need the entire
20 bytes of space reserved for media addresses, so the TIPC media type ID is
not explicitly stored in the packet payload.
Sample output of tipc-config:
# tipc-config -v -addr -netid -nt=all -p -m -b -n -ls
node address: <10.1.4>
current network id: 4711
Type Lower Upper Port Identity Publication Scope
0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster
167776260 167776260 <10.1.4:1216454657> 1216454658 zone
1 1 1 <10.1.4:1216479235> 1216479236 node
Ports:
1216479235: bound to {1,1}
1216454657: bound to {0,167776260}
Media:
eth
ib
Bearers:
ib:ib0
Nodes known:
<10.1.1>: up
Link <broadcast-link>
Window:20 packets
RX packets:0 fragments:0/0 bundles:0/0
TX packets:0 fragments:0/0 bundles:0/0
RX naks:0 defs:0 dups:0
TX naks:0 acks:0 dups:0
Congestion bearer:0 link:0 Send queue max:0 avg:0
Link <10.1.4:ib0-10.1.1:ib0>
ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets
RX packets:80 fragments:0/0 bundles:0/0
TX packets:40 fragments:0/0 bundles:0/0
TX profile sample:22 packets average:54 octets
0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0%
RX states:410 probes:213 naks:0 defs:0 dups:0
TX states:410 probes:197 naks:0 acks:0 dups:0
Congestion bearer:0 link:0 Send queue max:1 avg:0
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb->protocol field is used by packet classifiers and for AF_PACKET
cooked format, TIPC needs to set it properly.
Fixes packet classification and ethertype of 0x0000 in cooked captures:
Out 20:c9:d0:43:12:d9 ethertype Unknown (0x0000), length 56:
0x0000: 5b50 0028 0000 30d4 0100 1000 0100 1001 [P.(..0.........
0x0010: 0000 03e8 0000 0001 20c9 d043 12d9 0000 ...........C....
0x0020: 0000 0000 0000 0000 ........
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network protocols, like InfiniBand, don't have a fixed broadcast
address but one that depends on the configuration. Move the bcast_addr
to struct tipc_bearer and initialize it with the broadcast address of
the network device when the bearer is enabled.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove warning introduced by commit 418fc57 ("usbnet: cdc-ether: apply
usbnet_link_change"):
CHECK .../drivers/net/usb/cdc_ether.c
.../drivers/net/usb/cdc_ether.c:409:46: warning: incorrect type in argument 2 (different base types)
.../drivers/net/usb/cdc_ether.c:409:46: expected bool [unsigned] [usertype] <noident>
.../drivers/net/usb/cdc_ether.c:409:46: got restricted __le16 [usertype] wValue
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure sctp_ulpq is embedded into sctp_association and never
separately allocated, also ulpq->malloced is always 0, so that
kfree() is never called. Therefore, remove this code.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sctp_bind_addr structure has a 'malloced' member that is
always set to 0, thus in sctp_bind_addr_free() the kfree()
part can never be called. This part is embedded into
sctp_ep_common anyway and never alloced.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy