Now sctp increases sk_wmem_alloc by 1 when doing set_owner_w for the
skb allocked in sctp_packet_transmit and decreases by 1 when freeing
this skb.
But when this skb goes through networking stack, some subcomponents
might change skb->truesize and add the same amount on sk_wmem_alloc.
However sctp doesn't know the amount to decrease by, it would cause
a leak on sk->sk_wmem_alloc and the sock can never be freed.
Xiumei found this issue when it hit esp_output_head() by using sctp
over ipsec, where skb->truesize is added and so is sk->sk_wmem_alloc.
Since sctp has used sk_wmem_queued to count for writable space since
Commit cd305c74b0 ("sctp: use sk_wmem_queued to check for writable
space"), it's ok to fix it by counting sk_wmem_alloc by skb truesize
in sctp_packet_transmit.
Fixes: cac2661c53 ("esp4: Avoid skb_cow_data whenever possible")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other than asoc pmtu sync from all transports, sctp_assoc_sync_pmtu
is also processing transport pmtu_pending by icmp packets. But it's
meaningless to use sctp_dst_mtu(t->dst) as new pmtu for a transport.
The right pmtu value should come from the icmp packet, and it would
be saved into transport->mtu_info in this patch and used later when
the pmtu sync happens in sctp_sendmsg_to_asoc or sctp_packet_config.
Besides, without this patch, as pmtu can only be updated correctly
when receiving a icmp packet and no place is holding sock lock, it
will take long time if the sock is busy with sending packets.
Note that it doesn't process transport->mtu_info in .release_cb(),
as there is no enough information for pmtu update, like for which
asoc or transport. It is not worth traversing all asocs to check
pmtu_pending. So unlike tcp, sctp does this in tx path, for which
mtu_info needs to be atomic_t.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp GSO uses skb_gro_receive() to append the data into head
skb frag_list. However it actually only needs very few code from
skb_gro_receive(). Besides, NAPI_GRO_CB has to be set while most
of its members are not needed here.
This patch is to add sctp_packet_gso_append() to build GSO frames
instead of skb_gro_receive(), and it would avoid many unnecessary
checks and make the code clearer.
Note that sctp will use page frags instead of frag_list to build
GSO frames in another patch. But it may take time, as sctp's GSO
frames may have different size. skb_segment() can only split it
into the frags with the same size, which would break the border
of sctp chunks.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are now keeping the MTU information synced between asoc, transport
and dst, which makes the check at sctp_packet_config() not needed
anymore. As it was the sole caller to this function, lets remove it.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When given a MTU, this function calculates how much payload we can carry
on it. Without a MTU, it calculates the amount of header overhead we
have.
So that when we have extra overhead, like the one added for IP options
on SELinux patches, it is easier to handle it.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=p2Sh
-----END PGP SIGNATURE-----
Merge tag 'selinux-pr-20180403' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull SELinux updates from Paul Moore:
"A bigger than usual pull request for SELinux, 13 patches (lucky!)
along with a scary looking diffstat.
Although if you look a bit closer, excluding the usual minor
tweaks/fixes, there are really only two significant changes in this
pull request: the addition of proper SELinux access controls for SCTP
and the encapsulation of a lot of internal SELinux state.
The SCTP changes are the result of a multi-month effort (maybe even a
year or longer?) between the SELinux folks and the SCTP folks to add
proper SELinux controls. A special thanks go to Richard for seeing
this through and keeping the effort moving forward.
The state encapsulation work is a bit of janitorial work that came out
of some early work on SELinux namespacing. The question of namespacing
is still an open one, but I believe there is some real value in the
encapsulation work so we've split that out and are now sending that up
to you"
* tag 'selinux-pr-20180403' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: wrap AVC state
selinux: wrap selinuxfs state
selinux: fix handling of uninitialized selinux state in get_bools/classes
selinux: Update SELinux SCTP documentation
selinux: Fix ltp test connect-syscall failure
selinux: rename the {is,set}_enforcing() functions
selinux: wrap global selinux state
selinux: fix typo in selinux_netlbl_sctp_sk_clone declaration
selinux: Add SCTP support
sctp: Add LSM hooks
sctp: Add ip option support
security: Add support for SCTP security hooks
netlabel: If PF_INET6, check sk_buff ip header version
With refcnt support for sh_key, chunks auth sh_keys can be decided
before enqueuing it. Changing the active key later will not affect
the chunks already enqueued.
Furthermore, this is necessary when adding the support for authinfo
for sendmsg in next patch.
Note that struct sctp_chunk can't be grown due to that performance
drop issue on slow cpu, so it just reuses head_skb memory for shkey
in sctp_chunk.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ip option support to allow LSM security modules to utilise CIPSO/IPv4
and CALIPSO/IPv6 services.
Signed-off-by: Richard Haines <richard_c_haines@btinternet.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
assign_number is added as a member of sctp_stream_interleave, used
to assign ssn for data or mid (message id) for idata, called in
sctp_packet_append_data. sctp_chunk_assign_ssn is left as it is,
and sctp_chunk_assign_mid is added for sctp_stream_interleave_1.
This procedure is described in section 2.2.2 of RFC8260.
All sizeof(struct sctp_data_chunk) in tx path is replaced with
sctp_datachk_len, to make it right for idata as well. And also
adjust sctp_chunk_is_data for SCTP_CID_I_DATA.
After this patch, idata can be built and sent in tx path.
Note that if sp strm_interleave is set, it has to wait_connect in
sctp_sendmsg, as asoc intl_enable need to be known after 4 shake-
hands, to decide if it should use data or idata later. data and
idata can't be mixed to send in one asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_xmit_t, and
replace with enum sctp_xmit in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_data_chunk_t, and replace
with struct sctp_data_chunk in the places where it's using this
typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->csum_not_inet carries the indication on which algorithm is needed to
compute checksum on skb in the transmit path, when skb->ip_summed is equal
to CHECKSUM_PARTIAL. If skb carries a SCTP packet and crc32c hasn't been
yet written in L4 header, skb->csum_not_inet is assigned to 1; otherwise,
assume Internet Checksum is needed and thus set skb->csum_not_inet to 0.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is almost to revert commit 02f3d4ce9e ("sctp: Adjust PMTU
updates to accomodate route invalidation."). As t->asoc can't be NULL
in sctp_transport_update_pmtu, it could get sk from asoc, and no need
to pass sk into that function.
It is also to remove some duplicated codes from that function.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move sctp_transport_dst_check into sctp_packet_config
from sctp_packet_transmit and add pathmtu check in sctp_packet_config.
With this fix, sctp can update dst or pathmtu before appending chunks,
which can void dropping packets in sctp_packet_transmit when dst is
obsolete or dst's mtu is changed.
This patch is also to improve some other codes in sctp_packet_config.
It updates packet max_size with gso_max_size, checks for dst and
pathmtu, and appends ecne chunk only when packet is empty and asoc
is not NULL.
It makes sctp flush work better, as we only need to set up them once
for one flush schedule. It's also safe, since asoc is NULL only when
the packet is created by sctp_ootb_pkt_new in which it just gets the
new dst, no need to do more things for it other than set packet with
transport's pathmtu.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Laight noticed the support for MSG_MORE with datamsg->force_delay
didn't really work as we expected, as the first msg with MSG_MORE set
would always block the following chunks' dequeuing.
This Patch is to rewrite it by saving the MSG_MORE flag into assoc as
David Laight suggested.
asoc->force_delay is used to save MSG_MORE flag before a msg is sent.
All chunks in queue would not be sent out if asoc->force_delay is set
by the msg with MSG_MORE flag, until a new msg without MSG_MORE flag
clears asoc->force_delay.
Note that this change would not affect the flush is generated by other
triggers, like asoc->state != ESTABLISHED, queue size > pmtu etc.
v1->v2:
Not clear asoc->force_delay after sending the msg with MSG_MORE flag.
Fixes: 4ea0c32f5f ("sctp: add support for MSG_MORE")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Laight <david.laight@aculab.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c86a773c78 ("sctp: add dst_pending_confirm flag") introduced
a temporary variable "confirm" in sctp_packet_transmit.
But it broke the rule that longer lines should be above shorter ones.
Besides, this variable is not necessary, so this patch is to just
remove it and use tp->dst_pending_confirm directly.
Fixes: c86a773c78 ("sctp: add dst_pending_confirm flag")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is to add support for MSG_MORE on sctp.
It adds force_delay in sctp_datamsg to save MSG_MORE, and sets it after
creating datamsg according to the send flag. sctp_packet_can_append_data
then uses it to decide if the chunks of this msg will be sent at once or
delay it.
Note that unlike [1], this patch saves MSG_MORE in datamsg, instead of
in assoc. As sctp enqueues the chunks first, then dequeue them one by
one. If it's saved in assoc,the current msg's send flag (MSG_MORE) may
affect other chunks' bundling.
Since last patch, sctp flush out queue once assoc state falls into
SHUTDOWN_PENDING, the close block problem mentioned in [1] has been
solved as well.
[1] https://patchwork.ozlabs.org/patch/372404/
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new transport flag to allow sockets to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
The flag is propagated from transport to every packet.
It is reset when cached dst is reset.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effee8 ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bedf3 ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to use this cascading. It doesn't add anything.
Let's remove it and simplify.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding sctp gso, sctp_packet_transmit is a quite big function now.
This patch is to extract the codes for packing packet to sctp_packet_pack
from sctp_packet_transmit, and add some comments, simplify the err path by
freeing auth chunk when freeing packet chunk_list in out path and freeing
head skb early if it fails to pack packet.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7303a14750 ("sctp: identify chunks that need to be fragmented
at IP level") made the chunk be fragmented at IP level in the next round
if it's size exceed PMTU.
But there still is another case, PMTU can be updated if transport's dst
expires and transport's pmtu_pending is set in sctp_packet_transmit. If
the new PMTU is less than the chunk, the same issue with that commit can
be triggered.
So we should drop this packet and let it retransmit in another round
where it would be fragmented at IP level.
This patch is to fix it by checking the chunk size after PMTU may be
updated and dropping this packet if it's size exceed PMTU.
Fixes: 90017accff ("sctp: Add GSO support")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prsctp polices include ttl expires policy already, we should remove
the old ttl expires codes, and just adjust the new polices' codes to be
compatible with the old one for users.
This patch is to remove all the old expires codes, and if prsctp polices
are not set, it will still set msg's expires_at and check the expires in
sctp_check_abandoned.
Note that asoc->prsctp_enable is set by default, so users can't feel any
difference even if they use the old expires api in userspace.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp uses chunk->resent to record if a chunk is retransmitted, for
RTT measurements with retransmitted DATA chunks. chunk->sent_count was
introduced to record how many times one chunk has been sent for prsctp
RTX policy before. We actually can know if one chunk is retransmitted
by checking chunk->sent_count is greater than 1.
This patch is to remove resent from sctp_chunk and reuse sent_count
to avoid retransmitted chunks for RTT measurements.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To something more meaningful these days, specially because this is
working on packet headers or lengths and which are not tied to any CPU
arch but to the protocol itself.
So, WORD_TRUNC becomes SCTP_TRUNC4 and WORD_ROUND becomes SCTP_PAD4.
Reported-by: David Laight <David.Laight@ACULAB.COM>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David and Marcelo's suggestion, ENOMEM err shouldn't return back to
user in transmit path. Instead, sctp's retransmit would take care of
the chunks that fail to send because of ENOMEM.
This patch is only to do some release job when alloc_skb fails, not to
return ENOMEM back any more.
Besides, it also cleans up sctp_packet_transmit's err path, and fixes
some issues in err path:
- It didn't free the head skb in nomem: path.
- No need to check nskb in no_route: path.
- It should goto err: path if alloc_skb fails for head.
- Not all the NOMEMs should free nskb.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every time when sctp calls sctp_outq_flush, it sends out the chunks of
control queue, retransmit queue and data queue. Even if some trunks are
failed to transmit, it still has to flush all the transports, as it's
the only chance to clean that transmit_list.
So the latest transmit error here should be returned back. This transmit
error is an internal error of sctp stack.
I checked all the places where it uses the transmit error (the return
value of sctp_outq_flush), most of them are actually just save it to
sk_err.
Except for sctp_assoc/endpoint_bh_rcv, they will drop the chunk if
it's failed to send a REPLY, which is actually incorrect, as we can't
be sure the error that sctp_outq_flush returns is from sending that
REPLY.
So it's meaningless for sctp_outq_flush to return error back.
This patch is to save transmit error to sk_err in sctp_outq_flush, the
new error can update the old value. Eventually, sctp_wait_for_* would
check for it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, without GSO, it was easy to identify it: if the chunk didn't
fit and there was no data chunk in the packet yet, we could fragment at
IP level. So if there was an auth chunk and we were bundling a big data
chunk, it would fragment regardless of the size of the auth chunk. This
also works for the context of PMTU reductions.
But with GSO, we cannot distinguish such PMTU events anymore, as the
packet is allowed to exceed PMTU.
So we need another check: to ensure that the chunk that we are adding,
actually fits the current PMTU. If it doesn't, trigger a flush and let
it be fragmented at IP level in the next round.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp needs to queue auth chunk back when we know that we are going
to generate another segment. But commit f1533cce60 ("sctp: fix
panic when sending auth chunks") requeues the last chunk processed
which is probably not the auth chunk.
It causes panic when calculating the MAC in sctp_auth_calculate_hmac(),
as the incorrect offset of the auth chunk in skb->data.
This fix is to requeue it by using packet->auth.
Fixes: f1533cce60 ("sctp: fix panic when sending auth chunks")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
prsctp TTL policy is a policy to abandon chunks when they expire
at the specific time in local stack. It's similar with expires_at
in struct sctp_datamsg.
This patch uses sinfo->sinfo_timetolive to set the specific time for
TTL policy. sinfo->sinfo_timetolive is also used for msg->expires_at.
So if prsctp_enable or TTL policy is not enabled, msg->expires_at
still works as before.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we introduced GSO support, if using auth the auth chunk was being
left queued on the packet even after the final segment was generated.
Later on sctp_transmit_packet it calls sctp_packet_reset, which zeroed
the packet len while not accounting for this left-over. This caused more
space to be used the next packet due to the chunk still being queued,
but space which wasn't allocated as its size wasn't accounted.
The fix is to only queue it back when we know that we are going to
generate another segment.
Fixes: 90017accff ("sctp: Add GSO support")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
size_t objects should be printed with %Z printf format.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is useful for debugging packet sizes.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP has this pecualiarity that its packets cannot be just segmented to
(P)MTU. Its chunks must be contained in IP segments, padding respected.
So we can't just generate a big skb, set gso_size to the fragmentation
point and deliver it to IP layer.
This patch takes a different approach. SCTP will now build a skb as it
would be if it was received using GRO. That is, there will be a cover
skb with protocol headers and children ones containing the actual
segments, already segmented to a way that respects SCTP RFCs.
With that, we can tell skb_segment() to just split based on frag_list,
trusting its sizes are already in accordance.
This way SCTP can benefit from GSO and instead of passing several
packets through the stack, it can pass a single large packet.
v2:
- Added support for receiving GSO frames, as requested by Dave Miller.
- Clear skb->cb if packet is GSO (otherwise it's not used by SCTP)
- Added heuristics similar to what we have in TCP for not generating
single GSO packets that fills cwnd.
v3:
- consider sctphdr size in skb_gso_transport_seglen()
- rebased due to 5c7cdf339a ("gso: Remove arbitrary checks for
unsupported GSO")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point on delaying the packet if we can't fit a single byte
of data on it anymore. So lets just reduce the threshold by the amount
that a data chunk with 4 bytes (rounding) would use.
v2: based on the right tree
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow my patch for commit cea8768f33 ("sctp: allow
sctp_transmit_packet and others to use gfp") missed two important
chunks, which are now added.
Fixes: cea8768f33 ("sctp: allow sctp_transmit_packet and others to use gfp")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently sctp_sendmsg() triggers some calls that will allocate memory
with GFP_ATOMIC even when not necessary. In the case of
sctp_packet_transmit it will allocate a linear skb that will be used to
construct the packet and this may cause sends to fail due to ENOMEM more
often than anticipated specially with big MTUs.
This patch thus allows it to inherit gfp flags from upper calls so that
it can use GFP_KERNEL if it was triggered by a sctp_sendmsg call or
similar. All others, like retransmits or flushes started from BH, are
still allocated using GFP_ATOMIC.
In netperf tests this didn't result in any performance drawbacks when
memory is not too fragmented and made it trigger ENOMEM way less often.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To accomodate for enough headroom for tunnels, use MAX_HEADER instead
of LL_MAX_HEADER. Robert reported that he has hit after roughly 40hrs
of trinity an skb_under_panic() via SCTP output path (see reference).
I couldn't reproduce it from here, but not using MAX_HEADER as elsewhere
in other protocols might be one possible cause for this.
In any case, it looks like accounting on chunks themself seems to look
good as the skb already passed the SCTP output path and did not hit
any skb_over_panic(). Given tunneling was enabled in his .config, the
headroom would have been expanded by MAX_HEADER in this case.
Reported-by: Robert Święcki <robert@swiecki.net>
Reference: https://lkml.org/lkml/2014/12/1/507
Fixes: 594ccc14df ("[SCTP] Replace incorrect use of dev_alloc_skb with alloc_skb in sctp_packet_transmit().")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/Makefile
net/ipv6/sysctl_net_ipv6.c
Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.
In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>
MSG_MORE and 'corking' a socket would require that the transmit of
a data chunk be delayed.
Rename the return value to be less specific.
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for Nagle contains 6 separate checks all of which must be true
before a data packet is delayed.
Separate out each into its own 'if (test) return SCTP_XMIT_OK' so that
the reasons can be individually described.
Also return directly with SCTP_XMIT_RWND_FULL.
Delete the now-unused 'retval' variable and 'finish' label from
sctp_packet_can_append_data().
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by several people, rename local_df to ignore_df,
since it means "ignore df bit if it is set".
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long