Commit 4e27f752ab ("ARM: OMAP2+: Drop mmc platform data for am330x and
am43xx") dropped legacy mmc platform data for am3 and am4, but missed the
fact that we never updated the dts files for mmc3 that is directly on l3
interconnect instead of l4 interconnect. This leads to a situation with
no legacy platform data and incomplete dts data.
Let's update the mmc instances on l3 interconnect to probe properly with
ti-sysc interconnect target module driver to make mmc3 work again. Let's
still keep legacy "ti,hwmods" property around for v5.2 kernel and only
drop it later on.
Note that there is no need to use property status = "disabled" for mmc3.
The default for dts is enabled, and runtime PM will idle unused instances
just fine.
Fixes: 4e27f752ab ("ARM: OMAP2+: Drop mmc platform data for am330x and am43xx")
Reported-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the latest am572x[1] and dra74x[2] data manuals, mmc3
default, hs, sdr12 and sdr25 modes use iodelay values given in
MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is
selected and correct iodelay values can be configured.
[1] http://www.ti.com/lit/ds/symlink/am5728.pdf
[2] http://www.ti.com/lit/ds/symlink/dra746.pdf
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As seen on the AM335x TRM all the UARTs controller only are 0x1000 in size.
Fix this in the DTS.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now with the varity of several RPi boards, the memory should be defined
at board level. This step gives us the chance to fix the memory size
of the RPi 1 B+, Zero (incl. W) and Compute Module 1.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Eric Anholt <eric@anholt.net>
Starting with RPi 4 this is the first board, which doesn't use sdhost
as default SD interface. So the MMC interfaces should be defined finally at
board level. Since all boards using sdhci already does this, we can drop the
pinctrl part from bcm2835-rpi.dtsi.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Eric Anholt <eric@anholt.net>
Odroid-C1 uses the MAC address stored in eFuse at offset 0x1b4 (which is
defined as a "standard" offset for all Meson8 and Meson8b boards, but
testing shows that MXQ doesn't have the eFuse values programmed and
EC-100 stores it's MAC address in eMMC).
Add the nvmem cell which points to the MAC address and asssign it to the
Ethernet controller as "mac-address".
As result of this the MAC address which is stored in the eFuse is now
assigned to the Ethernet controller and consistent across reboots.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
CAM power domain contains CAMIF, 3AA and FIMC LITE devices. It is present
only in Exynos 5422/5800 SoCs. Currently there are no drivers nor the
device nodes for those devices, but instantiating its power domain allows
to turn it off and save some energy.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a power domain for G3D/Mali device present in Exynos542x/5800 SoCs.
Node for the Mali device will be added by a separate patch.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
DT nodes should be sorted by 'reg' property, so move MSC power domain
node in exynos5420.dtsi to the end of power domains to keep them sorted.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Exynos AHCI (SATA) controller has only one port for SATA device. According
to AHCI driver bindings (ata/ahci-platform.txt), if the bootloader doesn't
program the PORTS_IMPL register to proper value, the available port map has
to be provided by 'ports-implemented' device tree property. This fixes
SATA operation on Exynos5250-based boards since Linux v4.5.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The VDDEE regulator is basically a copy of the VCCK regulator. VDDEE
supplies for example the Mali GPU and is controlled by PWM_D instead of
PWM_C.
Add the VDDEE PWM regulator and make it the supply of the Mali GPU.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The VDDEE regulator is basically a copy of the VCCK regulator. VDDEE
supplies for example the Mali GPU and is controlled by PWM_D instead of
PWM_C.
Add the VDDEE PWM regulator and make it the supply of the Mali GPU.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The VDDEE regulator is basically a copy of the VCCK regulator. VDDEE
supplies for example the Mali GPU and is controlled by PWM_D instead of
PWM_C.
Add the VDDEE PWM regulator and make it the supply of the Mali GPU.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The PWM_D output is used for the VDDEE PWM regulator which supplies for
example the Mali GPU on the EC-100 and Odroid-C1 boards. Add the output
pin the VDDEE regulators can be added.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
If unspecified in DT, the fifo sizes are not automatically detected by
the dwmac1000 dma driver and the reported fifo sizes default to 0.
Because of this, flow control will be turned off on the device.
Add the fifo sizes provided by the datasheet in the SoC in DT so
flow control may be enabled if necessary.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Update the panel node with latest version of the panel used on the system.
Add missing pincontrol phandle to the panel node.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Before this change the device tree description of qspi node for
second memory on BK4 board was wrong (applicable to old, removed
fsl-quadspi.c driver).
As a result this memory was not recognized correctly when used
with the new spi-fsl-qspi.c driver.
From the dt-bindings:
"Required SPI slave node properties:
- reg: There are two buses (A and B) with two chip selects each.
This encodes to which bus and CS the flash is connected:
<0>: Bus A, CS 0
<1>: Bus A, CS 1
<2>: Bus B, CS 0
<3>: Bus B, CS 1"
According to above with new driver the second SPI-NOR memory shall
have reg=<2> as it is connected to Bus B, CS 0.
Fixes: a67d2c52a8 ("ARM: dts: Add support for Liebherr's BK4 device (vf610 based)")
Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the native-mode property inside the display-timings node.
According to
Documentation/devicetree/bindings/display/panel/display-timing.txt.
native-mode is a property of the display-timings node.
If it's located outside of display-timings, the native-mode setting is
ignored and the first display timing is used (which is a problem only if
someone adds another display timing).
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use a space before and after assignment operator to have consistent
style.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "vqmmc-1-8-v" and "ocr-limit" properties are not documented
anywhere, so just remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6qdl-wandboard can be connected to a OV5645 camera via
MIPI CSI port. Add support for it.
PAD_GPIO_6 has been originally used for the Ethernet FEC
ERR006687 workaround, but it needs to be used to provide the
camera sensor clock, so adjust it accordingly.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is like commit 0ca87bd5ba ("ARM: dts: rockchip: Add pin names
for rk3288-veyron-jerry") and other similar commits, but for the
veyron fievel board (and tiger, which includes the fievel .dtsi).
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fix/improve a few things for veyron fievel/tiger:
- move 'vccsys' regulator from tiger to fievel, both boards
have it (and tiger includes the fievel .dtsi)
- move 'ext_gmac' node below regulators
- fix GPIO ids of vcc5_host1 and vcc5_host2 regulators
- remove reset configuration from 'gmac' node, this is already done
in rk3288.dtsi
- fixed style issues of some multi-line comments
- switch 'vcc18_lcdt', 'vdd10_lcd' and 'vcc33_ccd' regulators off
during suspend
- no pull-up on the Bluetooth wake-up pin, there is an external
pull-up. The signal is active low, add the 'bt_host_wake_l'
pinctrl config
- move BC 1.2 pins up in the pinctrl config to keep 'wake only' pins
separate
- add BC 1.2 pins to sleep config
Fixes: 0067692b66 ("ARM: dts: rockchip: add veyron-fievel board")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch removes "ngpios" and "gpio-ranges" information from
stm32mp157-pinctrl.dtsi file as it is now filled in stm32mp157 pinctrl
package files.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The dsi physical layer is powered by the 1v8 power controller supply.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support of Cirrus cs42l51 audio codec on stm32mp157a-dk1 board.
Configuration overview:
- SAI2A is the CPU interface used for the codec audio playback
- SAI2B is the CPU interface used for the codec audio record
- SAI2A is configured as a clock provider for the audio codec
- SAI2A&B are configured as slave of the audio codec
- SAI2A&B share the same interface of the audio codec
Note:
In master mode, cs42l51 audio codec provides a bitclock
at 64 x FS, regardless of data width. This means that
slot width is always 32 bits.
Set slot width to 32 bits and slot number to 2
in SAI2A&B endpoint nodes, to match this constraint.
dai-tdm-slot-num and dai-tdm-slot-width properties are used here,
assuming that i2s is a special case of tdm, where slot number is 2.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On stm32mp157c, the ADC inputs are multiplexed with analog switches which
have reduced performances when their supply is below 2.7V (vdda by
default).
Add syscfg registers that can be used on stm32mp157c, to get full ADC
analog performances.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Fix compilations warnings detected by -Wall W=1 compilation option:
- node has a unit name, but no reg property
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Booster for ADC analog input switches can be used when Vdda is below 2.7V
to get maximum ADC analog performances.
Add booster for ADC analog switches on stm32mp157c.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Declare the M4 remote processor in a sub-node of the mlahb simple bus.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
vref fixed regulator shouldn't have unit address and reg properties.
Rename the label and phandle to "vref" according to the schematics.
Also remove it from simple-bus.
Fixes: 7465d81191 ("ARM: dts: stm32: enable ADC on stm32f429i-eval
board")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Added i2c mux for riser card and multiple ava card and its sensor
components for Facebook tiogapass platform
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Moved adc7 hwmon battery sensor to correct label to be read
by single applications for all adc sensors.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add initial version of device tree for Facebook Wedge100 AST2400 BMC
platform.
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add initial version of device tree for Facebook Wedge40 AST2400 BMC
platform.
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
"git diff" says:
\ No newline at end of file
after modifying the file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit b24413180f ("License cleanup: add SPDX GPL-2.0 license
identifier to files with no license") seem to have missed this
one file.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Change the FSI clock and data GPIOs to match what the hardware turned
out to use.
Fixes: 8e8fd0cbd7 ("ARM: dts: aspeed: Add Swift BMC machine")
Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Adriana Kobylak <anoo@us.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The dma dts node was missing the reset-names = "dma". The reset driver
needs this line to get the reset property.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Adjust GMAC1 clock lines skew to maximum (+960 ps) and TXD lines skew
to minimum (-420 ps), to improve signal integrity.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add missing buttons and signals to the VINING FPGA device tree,
so they are presented to the userspace via gpio-keys evdev.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
With commit d8e8fd0ebf ("mtd: rawnand: denali: decouple controller
and NAND chips"), the Denali NAND controller driver migrated to the
new controller/chip representation.
Update DT for it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Move USB PHYs to a standard arrays for Exynos EHCI/OHCI devices. This
resolves the conflict between Exynos EHCI/OHCI sub-nodes and generic USB
device bindings. Once the Exynos EHCI/OHCI sub-nodes are removed, the
boards can finally provide sub-nodes for the USB devices using generic USB
device bindings.
Suggested-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20190726081453.9456-4-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a space before and after assignment operator to have consistent
style.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This switches the kernel to parse the Redboot partitions
in the SL93512r and the NAS4220B properly using the
right compatible string instead of using hard-coded
partitions.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SL93512r board has its pin muxing set up for the wrong
ASIC: SL3516 instead of SL3512 that it is using. Fix it
up and reference the right GPIO for the WPS button.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Also known as the AOpen Chromebase Mini.
tiger and fievel are share the same board, tiger has a display and
touchscreen, fievel not. Use the fievel .dts as base and add the
extra bits.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
veyron jaq, jerry, minnie and speedy have mostly redundant regulator
and pinctrl configurations for the panel/backlight. Consolidate these
pieces in the eDP .dtsi.
Also change the default power supply for the panel to
'panel_regulator', instead of overriding it in all the board files.
pinky is the only device that uses 'vcc33_lcd' (the prior default),
so overwrite it in this case. pinky doesn't have a complete display
configuration, to keep things as they were delete the common nodes
that didn't exist previously in pinky's board file.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The chromebook .dtsi file contains common settings for veyron
Chromebooks with eDP displays. Some veyron devices with a display
aren't Chromebooks (e.g. 'tiger' aka 'AOpen Chromebase Mini'), move
display related bits from the chromebook .dtsi into a separate file
to avoid redundant DT settings.
The new file is included from the chromebook .dtsi and can be
included by non-Chromebook devices with a display.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The downstream Chrome OS 3.14 kernel for jerry limits WiFi TX power
through calibration data in the device tree [1]. Add a DT node for
the WiFi chip and use the downstream calibration data.
Not all calibration data entries have the length specified in the
binding (Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt),
however this is the data used by the downstream ('official') kernel
and the binding mentions that "the length can vary between hw
versions".
[1] https://crrev.com/c/271237
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds FMC2 NAND controller support used by stm32mp157c SOC.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The assigned register ranges for UART, SPI and I2C were too wasteful.
In order to avoid overlapping with the new functions on BCM2711
reduce the ranges.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Eric Anholt <eric@anholt.net>
Since A31, memory mapping of the IR driver has changed.
Prefer the A31 bindings instead of A13.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Since A31, memory mapping of the IR driver has changed.
Prefer the A31 bindings instead of A13.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
We are currently using a wrong register for dcan revision. Although
this is currently only used for detecting the dcan module, let's
fix it to avoid confusion.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ti,no-idle-on-init and ti,no-reset-on-init flags need to be at
the interconnect target module level for the modules that have it
defined. Otherwise we get the following warnings:
dts flag should be at module level for ti,no-idle-on-init
dts flag should be at module level for ti,no-reset-on-init
Reviewed-by: Suman Anna <s-anna@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Fix i.MX8MM SAI3 RXC/TXFS pinmux configuration.
- Fix i.MX7ULP usb-phy unit address to drop extra '0x' notation.
- Fix typo of clock frequency property name in a few i.MX6UL board
I2C buses.
- Drop "fsl,imx6sx-sai" from i.MX8M SAI device, as it's not compatible
with i.MX6SX SAI.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdNs2iAAoJEFBXWFqHsHzOyZ8H/3u3AjWSJxUa845cro1Q/Ibh
Ap2Skk9NgX3Wo9oRaet6Nc44iXG4zBXYfhVyzUG5H6t2mk4S2c2RaKLd55n6mHz0
6q1G57Z9ogxBzXrWgbiZtlCOlzZCNXVWZiB5eIUT12Mway+0HMEe4zcKAEvADZnt
c2tFf2AbjRe0ye1M2a6V09/TunIT8Hv2XH88vA4MxAJauOWNTkx4TrmXVNnokax+
S5Ha0Djr7seuHf6HLr95lB7QAj0ozTpZY17HsOmdFaO2UREVftm7JMhaNmxL072u
by1hwAALp9vYaDDzfw+7NjaquJiF6rGO6Vgi78d3brBFcXPSXmXpufUffl1aFWE=
=pQlh
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.3:
- Fix i.MX8MM SAI3 RXC/TXFS pinmux configuration.
- Fix i.MX7ULP usb-phy unit address to drop extra '0x' notation.
- Fix typo of clock frequency property name in a few i.MX6UL board
I2C buses.
- Drop "fsl,imx6sx-sai" from i.MX8M SAI device, as it's not compatible
with i.MX6SX SAI.
* tag 'imx-fixes-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mq: fix SAI compatible
arm64: dts: imx8mm: Correct SAI3 RXC/TXFS pin's mux option #1
ARM: dts: imx6ul: fix clock frequency property name of I2C buses
ARM: dts: imx7ulp: Fix usb-phy unit address format
Link: https://lore.kernel.org/r/20190723090827.GU15632@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
Even though the binding mentions that the PHY name must be "phy", it turns
out that all our DTs had "hdmi-phy" instead.
The code doesn't care about the phy-names property, so we can just change
our DTs to match the binding, without any side effect.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
simple-panel based bindings need only the display compatible, and
simple-panel isn't documented anywhere. Remove it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GIC is inside of SoC from architecture perspective, it should
be located inside of soc node in DT.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The thermal driver for the DB8500 was never properly converted
to device tree, the node should definitely be activated for
all board variants so move this down into the main SoC
DTSI, and default on.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel and
static replicator, so can dismiss warning during initialisation.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In addition to the PHYTEC phyCORE-i.MX 6UL the PHYTEC phyBOARD-Segin is
also available with the PHYTEC phyCORE-i.MX 6ULL. So this adds support
for this SOM and its baseboards.
It comes in a full featured option with either NAND flash or eMMC and in
a low cost option only available with NAND flash.
The hardware specs are:
- Full featured with NAND or eMMC:
* i.MX 6ULL Y2
* 512MB DDR3 memory
* 512MB NAND flash or 4GB/8GB eMMC
* Dual 10/100 Ethernet
* USB Host and USB OTG
* RS232
* MicroSD external storage
* Audio, RS232, I2C, SPI, CAN headers
* Further I/O options via A/V and Expansion headers
- Low cost with NAND:
* i.MX 6ULL Y0
* 256MB DDR3 memory
* 128MB NAND flash
* Single 10/100 Ethernet
* USB OTG
* RS232
* MicroSD external storage
* I2C
* Further I/O options via Expansion headers
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the imx6ul.dtsi include to the dts files so it is easier to reuse
the SOM dtsi for e.g. an i.MX 6ULL SOM.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ECSPI interface is available on the expansion connector of every
PHYTEC phyBOARD-Segin. Move its definition to the board include file
for better reuse.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The phyCORE-i.MX 6UL/ULL now can have eMMC instead of the NAND flash
memory. Add the eMMC node and disable it by default so it can be enabled
in case it is populated.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The phyCORE-i.MX 6UL/ULL now comes either with NAND flash or eMMC. We
have to configure the populated memory type in the device tree files. So
the GPMI node gets disabled by default and only enabled if populated.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To disable Ethernet interfaces in case they are not populated
make the FEC and Ethernet PHY status configurable in the dts files.
Also change the Ethernet PHYs labels to make them correspond to
the MDIO address.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix node name for the user LEDs to prevent the pinctrl of the phyCORE's
leds node from being overwritten. Also use more generic names for user
LEDs.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reduce the drive strength for the MDC, MDIO and TX pins of FEC1 and FEC2
on the phyBOARD-Segin to improve signal quality and EMC. Also disable
internal pull-ups on the MDC and MDIO pins.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is now a PHYTEC phyCORE-i.MX 6UL with eMMC instead of NAND flash
available. The dts filename needs to reflect that to differentiate both.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the same name scheme for the phyBOARD-Segin and the phyCORE-i.MX
6UL as is used for the PHYTEC phyBOARD-Mira and phyCORE-i.MX 6.
This is only a cosmetic change and there is no functional change
intended.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SGPM pinmux to ast2500-pinctrl function and group, to prepare for
supporting SGPIO in AST2500 SoC.
Signed-off-by: Hongwei Zhang <hongweiz@ami.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adds voltage regulators Infineon pxe1610 devices to Facebook
tiogapass platform.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Initial introduction of Lenovo Hr855xg2 family equipped with
Aspeed 2500 BMC SoC. Hr855xg2 is a x86 server development kit
with a ASPEED ast2500 BMC manufactured by Lenovo.
This adds the Hr855xg2 platform device tree file used by the Hr855xg2
BMC machines.
Signed-off-by: Andrew Peng <pengms1@lenovo.com>
Signed-off-by: Yonghui Liu <liuyh21@lenovo.com>
Signed-off-by: Lisa Liu <liuyj19@lenovo.com>
Signed-off-by: Harry Sung <hsung1@lenovo.com>
Signed-off-by: Derek Lin <dlin23@lenovo.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add initial version of device tree for Facebook Minipack ast2500 BMC.
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The DE2 bus takes two clocks, named bus and mod according to the binding.
However, the order of these clocks change from one SoC to another. Even
though it might not be an issue in most cases, having consistency will help
if we ever need to have some code to deal with deprecated bindings, and in
general it's just better.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A few boards set clock frequency of their I2C buses with
"clock_frequency" property. The right property is "clock-frequency".
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The phy device tree property has been deprecated in favor of phy-handle,
let's replace it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The DWMAC specific properties to manage the PHY have been superseeded by
the generic PHY properties. Let's move to it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
To make use of the new eLCDIF DRM driver OF graph description is
required. Describe the display using OF graph nodes.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following warning is seen when building with W=1:
arch/arm/boot/dts/imx7ulp.dtsi:189.31-195.5: Warning (simple_bus_reg): /bus@40000000/usb-phy@0x40350000: simple-bus unit address format error, expected "40350000"
Fix it as suggested by removing the extra "0x" notation.
Fixes: 5b7bd45631 ("ARM: dts: imx7ulp: add imx7ulp USBOTG1 support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 4664179fe6 ("ARM: dts: imx7s: Enable SNVS power key
according to board design") snvs_pwrkey is disabled by default, so there
is no need for disabling it explicitly in the board dts anymore.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 4664179fe6 ("ARM: dts: imx7s: Enable SNVS power key
according to board design") snvs_pwrkey is disabled by default, so there
is no need for disabling it explicitly in the board dts anymore.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Correct sdma compatible since ecspi errata ERR009165 has been fixed
on i.mx6sll as i.mx6ul.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Just like we did for rk3288-veyron-chromebook, we want to be able to
use one of the fixed PLLs in the system to make the pixel clock for
minnie.
Specifying these timings matches us with how the display is used on
the downstream Chrome OS kernel. See https://crrev.com/c/323211.
Unlike what we did for rk3288-veyron-chromebook, this CL actually
changes the timings (though not the pixel clock) that is used when
using the upstream kernel. Booting up a minnie shows that it ended up
with a 66.67 MHz pixel clock but it was still using the
porches/blankings it would have wanted for a 72.5 MHz pixel clock.
NOTE: compared to the downstream kernel, this seems to cause a
slightly different result reported in the 'modetest' command on a
Chromebook. The downstream kernel shows:
1280x800 60 1280 1298 1330 1351 800 804 822 830 66667
With this patch we have:
1280x800 59 1280 1298 1330 1351 800 804 822 830 66666
Specifically modetest was reporting 60 Hz on the downstream kernel but
the upstream kernel does the math and comesup with 59 (because we
actually achieve 59.45 Hz). Also upstream doesn't round the Hz up
when converting to kHz--it seems to truncate.
ALSO NOTE: when I look at the EDID from the datasheet, I see:
-hsync -vsync
...but it seems like we've never actually run with that so I've
continued leaving that out.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Let's document the display timings that most veyron chromebooks (like
jaq, jerry, mighty, speedy) have been using out in the field. This
uses the standard blankings but a slightly slower clock rate, thus
getting a refresh rate 58.3 Hz.
NOTE: this won't really do anything except cause DRM to properly
report the refresh rate since vop_crtc_mode_fixup() was rounding the
pixel clock to 74.25 MHz anyway. Apparently the adjusted rate isn't
exposed to userspace so it's important that the rate we're trying to
achieve is mostly right.
For the downstream kernel change related to this see See
https://crrev.com/c/324558.
NOTE: minnie uses a different panel will be fixed up in a future
patch, so for now we'll just delete the panel timings there.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
While properties and child nodes with the same name are valid DT, the
practice is not encouraged. Furthermore, the collision is problematic for
YAML encoded DT. Let's just avoid the issue and rename the nodes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190516225614.1458-1-robh@kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We continue to see a lot of new material. I've highlighted some of it
below, but there's been more beyond that as well.
One of the sweeping changes is that many boards have seen their ARM Mali
GPU devices added to device trees, since the DRM drivers have now been
merged.
So, with the caveat that I have surely missed several great
contributions, here's a collection of the material this time around:
New SoCs:
- Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53)
- TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA)
- Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53)
New Boards / platforms:
- Aspeed BMC support for a number of new server platforms
- Kontron SMARC SoM (several i.MX6 versions)
- Novtech's Meerkat96 (i.MX7)
- ST Micro Avenger96 board
- Hardkernel ODROID-N2 (Amlogic G12B)
- Purism Librem5 devkit (i.MX8MQ)
- Google Cheza (Qualcomm SDM845)
- Qualcomm Dragonboard 845c (Qualcomm SDM845)
- Hugsun X99 TV Box (Rockchip RK3399)
- Khadas Edge/Edge-V/Captain (Rockchip RK3399)
Updated / expanded boards and platforms:
- Renesas r7s9210 has a lot of new peripherals added
- Polish and fixes for Rockchip-based Chromebooks
- Amlogic G12A has a lot of peripherals added
- Nvidia Jetson Nano sees various fixes and improvements, and is now at
feature parity with TX1
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl0yUswPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3BrEP/2Hrqr9MHWSZ65iLmRkrMIMQ0nxxngN5//Jt
AlrmyBixwnV3l1eP5lpZT9VlXQL8lo7fkx+03fHPUaKxBihl6DN8LGsSnsT7Wnzu
aGA8SiJmdZhk8f1C30gGNssBBvOdJeTmc0vQzeKXJA6g4ra3+bmwn+T6OLEEGZlO
g0pl7BXST9lNLFlSBEG6DcjNL7m1mqCWpaRmWe70zjbFT86KKb/5YISY61fC7Qkf
AHccunoSXFBM6ttoIubxCInTkhfhKalJyZ2cUPZ6MRxhoE0+ABVOk2lw1oMmF3er
OOz8Qs9AcZcsC6k+WAxJgMjT8snTc8wRh273Df8drGfTzSgGkuXj0Uimmgmaqsts
3xPKu+6+UY+HxDt52NOQ4p/eo8yPMgVutfG7ciGynHZSgsklscLXMvUL7EGH67hR
AfJQFWJ3K+Jk/KeyyGgi1pa2C4BoJ1VmPw1P9oLHRMuuCLrY1B2XzG7nySX81uNG
2uTbLL236o2oUX3E/yaLN1k2tkreddG1G48HVw/srcIImAxD5Dl1sysRzMQRUWBw
tN5ZecSuz/JMQj5HaieZ8zL/v9dXzq6Gielee8SAJaO38nbnmxv3DfTHLLEoy3nv
mS/1OtySzbzI9obMZIsw+bpxDokvb525k89gthxBfWybm6KCRGJO119zc5nZ9r8G
PX5wvaPi
=sHZs
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM Devicetree updates from Olof Johansson:
"We continue to see a lot of new material. I've highlighted some of it
below, but there's been more beyond that as well.
One of the sweeping changes is that many boards have seen their ARM
Mali GPU devices added to device trees, since the DRM drivers have now
been merged.
So, with the caveat that I have surely missed several great
contributions, here's a collection of the material this time around:
New SoCs:
- Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53)
- TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA)
- Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53)
New Boards / platforms:
- Aspeed BMC support for a number of new server platforms
- Kontron SMARC SoM (several i.MX6 versions)
- Novtech's Meerkat96 (i.MX7)
- ST Micro Avenger96 board
- Hardkernel ODROID-N2 (Amlogic G12B)
- Purism Librem5 devkit (i.MX8MQ)
- Google Cheza (Qualcomm SDM845)
- Qualcomm Dragonboard 845c (Qualcomm SDM845)
- Hugsun X99 TV Box (Rockchip RK3399)
- Khadas Edge/Edge-V/Captain (Rockchip RK3399)
Updated / expanded boards and platforms:
- Renesas r7s9210 has a lot of new peripherals added
- Fixes and polish for Rockchip-based Chromebooks
- Amlogic G12A has a lot of peripherals added
- Nvidia Jetson Nano sees various fixes and improvements, and is now
at feature parity with TX1"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (586 commits)
ARM: dts: gemini: Set DIR-685 SPI CS as active low
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Arndale Octa
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Odroid XU3 family
ARM: dts: exynos: Move Mali400 GPU node to "/soc"
ARM: dts: exynos: Fix imprecise abort on Mali GPU probe on Exynos4210
arm64: dts: qcom: qcs404: Add missing space for cooling-cells property
arm64: dts: rockchip: Fix USB3 Type-C on rk3399-sapphire
arm64: dts: rockchip: Update DWC3 modules on RK3399 SoCs
arm64: dts: rockchip: enable rk3328 watchdog clock
ARM: dts: rockchip: add display nodes for rk322x
ARM: dts: rockchip: fix vop iommu-cells on rk322x
arm64: dts: rockchip: Add support for Hugsun X99 TV Box
arm64: dts: rockchip: Define values for the IPA governor for rock960
arm64: dts: rockchip: Fix multiple thermal zones conflict in rk3399.dtsi
arm64: dts: rockchip: add core dtsi file for RK3399Pro SoCs
arm64: dts: rockchip: improve rk3328-roc-cc rgmii performance.
Revert "ARM: dts: rockchip: set PWM delay backlight settings for Minnie"
ARM: dts: rockchip: Configure BT_DEV_WAKE in on rk3288-veyron
arm64: dts: qcom: sdm845-cheza: add initial cheza dt
ARM: dts: msm8974-FP2: Add vibration motor
...
The SPI to the display on the DIR-685 is active low, we were
just saved by the SPI library enforcing active low on everything
before, so set it as active low to avoid ambiguity.
Link: https://lore.kernel.org/r/20190715202101.16060-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while with
no reported issues. Nothing is earth-shattering, just constant forward
progress for more devices supported and cleanups and small fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed in.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSXjYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynMYACgnSRP3GylwMywrkc9paVmDeiIgNwAn0N2sika
JEW7C3lkBJZJ7R6V/Ynm
=drla
-----END PGP SIGNATURE-----
Merge tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY updates from Greg KH:
"Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while
with no reported issues. Nothing is earth-shattering, just constant
forward progress for more devices supported and cleanups and small
fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed
in"
* tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (145 commits)
Revert "usb: gadget: storage: Remove warning message"
Revert "dt-bindings: add binding for USBSS-DRD controller."
Revert "usb:gadget Separated decoding functions from dwc3 driver."
Revert "usb:gadget Patch simplify usb_decode_set_clear_feature function."
Revert "usb:gadget Simplify usb_decode_get_set_descriptor function."
Revert "usb:cdns3 Add Cadence USB3 DRD Driver"
Revert "usb:cdns3 Fix for stuck packets in on-chip OUT buffer."
usb :fsl: Change string format for errata property
usb: host: Stops USB controller init if PLL fails to lock
usb: linux/fsl_device: Add platform member has_fsl_erratum_a006918
usb: phy: Workaround for USB erratum-A005728
usb: fsl: Set USB_EN bit to select ULPI phy
usb: Handle USB3 remote wakeup for LPM enabled devices correctly
drivers/usb/typec/tps6598x.c: fix 4CC cmd write
drivers/usb/typec/tps6598x.c: fix portinfo width
usb: storage: scsiglue: Do not skip VPD if try_vpd_pages is set
usb: renesas_usbhs: add a workaround for a race condition of workqueue
usb: gadget: udc: renesas_usb3: remove redundant assignment to ret
usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
USB: gadget: function: fix issue Unneeded variable: "value"
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
1. Fix imprecise abort on Exynos4210 caused by newly added Mali nodes,
2. Reorganize Mali nodes under /soc,
3. Adjust buck regulators voltages on Arndale Octa and Odroid XU3/XU4
family to sane values.
-----BEGIN PGP SIGNATURE-----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=4yv0
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.3-3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.3, third round
1. Fix imprecise abort on Exynos4210 caused by newly added Mali nodes,
2. Reorganize Mali nodes under /soc,
3. Adjust buck regulators voltages on Arndale Octa and Odroid XU3/XU4
family to sane values.
* tag 'samsung-dt-5.3-3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Arndale Octa
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Odroid XU3 family
ARM: dts: exynos: Move Mali400 GPU node to "/soc"
ARM: dts: exynos: Fix imprecise abort on Mali GPU probe on Exynos4210
Link: https://lore.kernel.org/r/20190707180115.5562-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
OHCI driver was converted over to use GPIO regulators.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vwpF
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v5.2-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes
This set of patches fixes regressions introduced in v5.2 kernel when DA8xx
OHCI driver was converted over to use GPIO regulators.
* tag 'davinci-fixes-for-v5.2-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da830-evm: fix GPIO lookup for OHCI
ARM: davinci: omapl138-hawk: add missing regulator constraints for OHCI
ARM: davinci: da830-evm: add missing regulator constraints for OHCI
+ Linux 5.2-rc7
Signed-off-by: Olof Johansson <olof@lixom.net>
for rk3288-veyron boards.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl0Z0DEQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgbHRB/40x1DBDesIZnjpbnFPTBGcqhMXgc/tfawK
jtU7fwFiToyvXXzauY877+njhC54MCwF9JhtRfxn0c5O7WRBCnZnzRIfQpqKxdXD
VmIx5cKMI057oG0p4RB9tSDTHNAfg0lw9M9DQVw4f/Yl2M0kY/yk3TnL2vReMxMQ
mGd0j8KDAHnpdBgYpKQPSxQdbV8i5EFkb0RcvrEZ/VPHrikg74y91nbgSjBu3EgI
+NecSglseOG+SVzPzxbnU1kZ4E7Z/zXq6UQmpoVw2710MNn+QWrd1+F7bAcnszaO
KJCdHRM8Icpx9mNnekjonzYuNWOAEZf+LFS2FncR6qjrzFgBWi7c
=8Tz/
-----END PGP SIGNATURE-----
Merge tag 'v5.3-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Display support for rk3228/rk3229 (up to hdmi output) and more love
for rk3288-veyron boards.
* tag 'v5.3-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add display nodes for rk322x
ARM: dts: rockchip: fix vop iommu-cells on rk322x
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
Revert "ARM: dts: rockchip: set PWM delay backlight settings for Minnie"
ARM: dts: rockchip: Configure BT_DEV_WAKE in on rk3288-veyron
ARM: dts: rockchip: Configure BT_HOST_WAKE as wake-up signal on veyron
Signed-off-by: Olof Johansson <olof@lixom.net>
Use the armada-38x-uart compatible strings for Armada XP 98dx3236 SoCs
in order to not loose character anymore.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXRYouQAKCRALBhiOFHI7
1XlVAJ0Qjg4gFXUrf7MUpn8LuUi6UTEf3ACdGLW5ZT78BM78TiEGG79H+WsJ/ow=
=jxUU
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-5.2-2' of git://git.infradead.org/linux-mvebu into arm/fixes
mvebu fixes for 5.2 (part 2)
Use the armada-38x-uart compatible strings for Armada XP 98dx3236 SoCs
in order to not loose character anymore.
* tag 'mvebu-fixes-5.2-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-xp-98dx3236: Switch to armada-38x-uart serial node
Signed-off-by: Olof Johansson <olof@lixom.net>
The datasheet of S2MPS11 PMIC is slightly non-consistent in buck[78]
voltage regulators values.
1. The voltage tables for configuring their registers mention range of
voltages: 0.750 V to 3.55 V,
2. The constrains in electrical specifications say output voltage range
to be different (buck7: 1.2 V to 1.5 V, buck8: 1.8 V to 2.1 V).
Adjust the ranges to match the electrical specifications to stay on the
safe side. Anyway these regulators stay at default value so this should
not have effect.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The datasheet of S2MPS11 PMIC is slightly non-consistent in buck[78]
voltage regulators values.
1. The voltage tables for configuring their registers mention range of
voltages: 0.750 V to 3.55 V,
2. The constrains in electrical specifications say output voltage range
to be different (buck7: 1.2 V to 1.5 V, buck8: 1.8 V to 2.1 V).
Adjust the ranges to match the electrical specifications to stay on the
safe side. Also change the name of regulators to match reality. Anyway
these regulators stay at default value so this should not have effect.
Reported-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Mali400 GPU hardware module is a standard hardware module integrated to
Exynos3210/4210/4412 SoCs, so it should reside under the "/soc" node.
The only SoC components which are placed in the DT root, are those, which
are a part of CPUs: like ARM architected timers and ARM performance
measurement units.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The PMU module of Mali400 GPU is optional and it looks that it is not
present on Exynos4210, because any access to its registers causes external
abort. This patch removes "pmu" interrupt for Exynos4210 SoCs, so the
driver will skip the PMU module. This fixes following fault during kernel
boot:
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
(lima_pmu_init) from [<c059e6f8>] (lima_device_init+0x244/0x5a0)
(lima_device_init) from [<c059e40c>] (lima_pdev_probe+0x7c/0xd8)
(lima_pdev_probe) from [<c05afcb8>] (platform_drv_probe+0x48/0x9c)
(platform_drv_probe) from [<c05ad594>] (really_probe+0x1c4/0x400)
(really_probe) from [<c05ad988>] (driver_probe_device+0x78/0x1b8)
(driver_probe_device) from [<c05add30>] (device_driver_attach+0x58/0x60)
(device_driver_attach) from [<c05ade34>] (__driver_attach+0xfc/0x160)
(__driver_attach) from [<c05ab650>] (bus_for_each_dev+0x68/0xb4)
(bus_for_each_dev) from [<c05ac734>] (bus_add_driver+0x104/0x20c)
(bus_add_driver) from [<c05aece0>] (driver_register+0x78/0x10c)
(driver_register) from [<c0103214>] (do_one_initcall+0x8c/0x430)
(do_one_initcall) from [<c0f01328>] (kernel_init_freeable+0x3c8/0x4d0)
(kernel_init_freeable) from [<c0ac3aa0>] (kernel_init+0x8/0x10c)
(kernel_init) from [<c01010b4>] (ret_from_fork+0x14/0x20)
The PMU module seems to work fine on Exynos4412 SoCs, so the patch also
moves the interrupt definitions to exynos4210.dtsi and exynos4412.dtsi
respectively, to keep only the common part in exynos4.dtsi.
Fixes: 13efd80aca ("ARM: dts: exynos: Add GPU/Mali 400 node to Exynos4")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The biggest part here is a set of patches removing unnecesary variables
from several drivers.
Meson-g12a's dwc3 glue implemented IRQ-based OTG/DRD role swap.
Qcom's dwc3 glue added support for ACPI, mainly for the AArch64-based
SoCs.
DWC3 also got support for Intel Elkhart Lake platforms.
-----BEGIN PGP SIGNATURE-----
iQJRBAABCAA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAl0UdeMdHGZlbGlwZS5i
YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQbuBxAAqMp9nwVgYu9beeXP
1xEjfnc/OxA8oMPcbJVPiYseVowbrj5Ue3SK8XcDCeSDfEI09PNOqfpNtLXvjVie
NxDMj1zj31Ggb0XfoweOZQHXXpq/6tlfqVJ/oXfkxQ92wuSlyKzkoA7ZuCxAy9ay
p+E+/cSa1E5LGigI/XEyX2C9JuANd9vSM/CaA5Z2XbosThLK9svtHWlNRIPolIGB
fUBRm3JVi1jLxAMfbu/8Ng05xYGIPnwi8JDcQ8swAdm5nENtuq9Z0eMm8EAxLdvn
UwArRR14uI4Vgs69IH4R28tmM4MMsuUVnKv3nxOYcoqQ01u9dySiEYsT5x7RETLu
GH7v4NMdTqTIfN8ECFLUfaE8+tLBx6MjFOBxNHIeu1tc+MrRzb7a7Z00dkpUlMkg
jaddCfwbAx3CgJ77nDILBYnVRpaEzlKhZWrNkoSCUI1Ty0QlsnInUkhXtUuayi+R
AjCBc1PBXPOc6FHx5ECQrA0HWBhC0MW23ncdAFxz1eqqJPYhNbPn5zPEaZ8nNvmz
R1aUlxDi8FDyRvKbjmGoeRrLbiwzcu/9xiLZ13U4H/kPG4+1g+rx3F8ExIvWr1p+
XrCJCDdYKN+D9KxbO/5ERg38fARsynryXp4Yll4cLR7IWCQZykkVJ+MuLDwejNF1
itw69proXZUqZ3Voa9C5a1V/gCQ=
=3HLl
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v5.3 merge window
The biggest part here is a set of patches removing unnecesary variables
from several drivers.
Meson-g12a's dwc3 glue implemented IRQ-based OTG/DRD role swap.
Qcom's dwc3 glue added support for ACPI, mainly for the AArch64-based
SoCs.
DWC3 also got support for Intel Elkhart Lake platforms.
* tag 'usb-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (30 commits)
usb: dwc3: remove unused @lock member of dwc3_ep struct
usb: dwc3: pci: Add Support for Intel Elkhart Lake Devices
usb: Replace snprintf with scnprintf in gether_get_ifname
usb: gadget: ether: Fix race between gether_disconnect and rx_submit
usb: gadget: storage: Remove warning message
usb: dwc3: gadget: Add support for disabling U1 and U2 entries
usb: gadget: send usb_gadget as an argument in get_config_params
doc: dt: bindings: usb: dwc3: Update entries for disabling U1 and U2
usb: dwc3: qcom: Use of_clk_get_parent_count()
usb: dwc3: Fix core validation in probe, move after clocks are enabled
usb: dwc3: qcom: Improve error handling
usb: dwc3: qcom: Start USB in 'host mode' on the SDM845
usb: dwc3: qcom: Add support for booting with ACPI
soc: qcom: geni: Add support for ACPI
Revert "usb: dwc2: host: Setting qtd to NULL after freeing it"
usb: gadget: net2272: remove redundant assignments to pointer 's'
usb: gadget: Zero ffs_io_data
USB: omap_udc: Remove unneeded variable
fotg210-udc: Remove unneeded variable
usb: gadget: at91_udc: Remove unneeded variable
...
* Add vibrator motor for MSM8974 based Fairphone 2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=W5di
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm Device Tree Changes for v5.3
* Add vibrator motor for MSM8974 based Fairphone 2
* tag 'qcom-dts-for-5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: msm8974-FP2: Add vibration motor
Signed-off-by: Olof Johansson <olof@lixom.net>
A smaller batch of fixes, nothing that stands out as risky or scary.
Mostly DTS tweaks for a few issues:
- GPU fixlets for Meson
- CPU idle fix for LS1028A
- PWM interrupt fixes for i.MX6UL
Also, enable a driver (FSL_EDMA) on arm64 defconfig, and a warning and
two MAINTAINER tweaks.
-----BEGIN PGP SIGNATURE-----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=Jr9u
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A smaller batch of fixes, nothing that stands out as risky or scary.
Mostly DTS tweaks for a few issues:
- GPU fixlets for Meson
- CPU idle fix for LS1028A
- PWM interrupt fixes for i.MX6UL
Also, enable a driver (FSL_EDMA) on arm64 defconfig, and a warning and
two MAINTAINER tweaks"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: imx6ul: fix PWM[1-4] interrupts
ARM: omap2: remove incorrect __init annotation
ARM: dts: gemini Fix up DNS-313 compatible string
ARM: dts: Blank D-Link DIR-685 console
arm64: defconfig: Enable FSL_EDMA driver
arm64: dts: ls1028a: Fix CPU idle fail.
MAINTAINERS: BCM53573: Add internal Broadcom mailing list
MAINTAINERS: BCM2835: Add internal Broadcom mailing list
ARM: dts: meson8b: fix the operating voltage of the Mali GPU
ARM: dts: meson8b: drop undocumented property from the Mali GPU node
ARM: dts: meson8: fix GPU interrupts and drop an undocumented property
Switch to the "marvell,armada-38x-uart" driver variant to empty
the UART buffer before writing to the UART_LCR register.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>.
Cc: stable@vger.kernel.org
Fixes: 43e28ba877 ("ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and
am57xx-evms don't have this capability, disable voltage switching for
these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
commit 88a748419b ("ARM: dts: am57xx-idk: Remove support for voltage
switching for SD card") did this only for idk boards. Do it for all
affected boards.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add display_subsystem, hdmi_phy, vop, and hdmi device nodes plus
a few hdmi pinctrl entries to allow for HDMI output.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
[added assigned-clock settings for hdmiphy output]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
1. Add camera flash to Galaxy S3 boards,
2. Fix PMU affinity interrupt warning on Exynos4,
3. Improve regulator configuration on Odroid XU3/XU4/HC1 family and
Arndale Octa by disabling unneeded regulators and adding suspend
configuration. The suspend configuration brings significant reduce of
energy usage in Suspend to RAM (e.g. 120 -> ~7 mA on Odroid HC1).
4. Add Mali nodes to Exynos3 and Exynos4.
-----BEGIN PGP SIGNATURE-----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=ZMHl
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.3, second round
1. Add camera flash to Galaxy S3 boards,
2. Fix PMU affinity interrupt warning on Exynos4,
3. Improve regulator configuration on Odroid XU3/XU4/HC1 family and
Arndale Octa by disabling unneeded regulators and adding suspend
configuration. The suspend configuration brings significant reduce of
energy usage in Suspend to RAM (e.g. 120 -> ~7 mA on Odroid HC1).
4. Add Mali nodes to Exynos3 and Exynos4.
* tag 'samsung-dt-5.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add GPU/Mali 400 node to Exynos4
ARM: dts: exynos: Add GPU/Mali 400 node to Exynos3250
dt-bindings: gpu: mali: Add Samsung compatibles for Midgard and Utgard
ARM: dts: exynos: Use proper regulator for eMMC memory on Arndale Octa
ARM: dts: exynos: Add regulator suspend configuration to Odroid XU3/XU4/HC1 family
ARM: dts: exynos: Add regulator suspend configuration to Arndale Octa board
ARM: dts: exynos: Disable unused buck10 regulator on Odroid HC1 board
ARM: dts: exynos: Fix language typo and indentation
ARM: dts: exynos: Add PMU interrupt affinity to Exynos4 boards
ARM: dts: exynos: Add flash support to Galaxy S3 boards
Signed-off-by: Olof Johansson <olof@lixom.net>
- Migrate to the new binding for the Denali NAND controller
-----BEGIN PGP SIGNATURE-----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=Ezcw
-----END PGP SIGNATURE-----
Merge tag 'uniphier-dt-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM SoC DT updates for v5.3
- Migrate to the new binding for the Denali NAND controller
* tag 'uniphier-dt-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: update to new Denali NAND binding
Signed-off-by: Olof Johansson <olof@lixom.net>
This reverts commit 288ceb85b5.
The commit assumes that the minnie panel is a AUO B101EAN01.1 (LVDS
interface), however it is a AUO B101EAN01.8 (eDP interface). The eDP
panel doesn't need the 200 ms delay.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is the other half of the hacky solution from commit f497ab6b4b
("ARM: dts: rockchip: Configure BT_HOST_WAKE as wake-up signal on
veyron"). Specifically the LPM driver that the Broadcom Bluetooth
expects to have (but is missing in mainline) has two halves of the
equation: BT_HOST_WAKE and BT_DEV_WAKE. The BT_HOST_WAKE (which was
handled in the previous commit) is the one that lets the Bluetooth
wake the system up. The BT_DEV_WAKE (this patch) tells the Bluetooth
that it's OK to go into a low power mode. That means we were burning
a bit of extra power in S3 without this patch. Measurements are a bit
noisy, but it appears to be a few mA worth of difference.
NOTE: Though these pins don't do much on systems with Marvell
Bluetooth, downstream kernels set it on all veyron boards so we'll do
the same.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With commit d8e8fd0ebf ("mtd: rawnand: denali: decouple controller
and NAND chips"), the Denali NAND controller driver migrated to the
new controller/chip representation.
Update DT for it.
In the new binding, the number of connected chips are described in
DT instead of run-time probed.
I added just one chip to the reference boards, where we do not know
if the on-board NAND device is a single chip or multiple chips.
If we added too many chips into DT, it would end up with the timeout
error in nand_scan_ident().
I changed all the pinctrl properties to use the single CS.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- New board support: iMX6-based Kontron SMARC-sAMX6i, i.MX7D based
Meerkat96 board, and NXP LS1021A-TSN board.
- A series from Andrey Smirnov to update vf610-zii-dev and
imx7d-zii-rpu2 board, fixing UART2 pin assignment and stdout-path,
adding QSPI device, and dropping unused pinmux.
- Update imx6sl and imx6qdl device tree to assign corresponding clocks
instead of dummy clock.
- Update i.MX6/7 boards from NXP to assign corresponding power supply
for LDOs.
- Update i.MX6/7 device trees to enable SNVS poweroff key support
according to board design.
- Update coresight DT binding for i.MX7 according to consolidations
for CoreSight replicator and funnel.
- A series from Marek Vasut to update M53Menlo board on various devices
like UART, USB, ethernet PHY, GPIOs etc.
- Enable USBOTG support for imx7ulp and evk board.
- A series from Peter Robinson to update imx6sx-udoo board, switching
to SPDX License Identifier, enabling I2C devices and bluetooth
support.
- Add video capture support for i.MX53 and imx53-smd board.
- Add PXP device for i.MX6UL.
- Other random small updates on various boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdEbs9AAoJEFBXWFqHsHzOkIoIAKBS9jB7Lp6DSGpYIgwdjBmK
PY0ogud8FZEfHFdDi9WGt3d1KFkr0xBJPvJ1Tn48BdpN/k3TMrFs1sj/PRNlIRe5
llnBpCD5oV7SHAdIkFcGIQeWwHMfnpxe1NdhMiCpT6pKtk2oieRWVs0RvdZ5UgRI
aULSFbxs/ZEjvVa3Jcx7KjFmceCHP8naICtYm7ZYjn3vDI7y1ZosaD9pWFSL3N/k
l/F3B05Zh6HA4HpldGxCbxSVr94GE9HgLXGigo/nEGjiHmhecc2rievsegJP9AKa
z1bTtIK+qrsYmUtXWGPgNTXLpVfjRf+0Q6z60uVDhsfuNJx2IVJkyBeAebXCSMk=
=pBgY
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm32 DT changes for 5.3:
- New board support: iMX6-based Kontron SMARC-sAMX6i, i.MX7D based
Meerkat96 board, and NXP LS1021A-TSN board.
- A series from Andrey Smirnov to update vf610-zii-dev and
imx7d-zii-rpu2 board, fixing UART2 pin assignment and stdout-path,
adding QSPI device, and dropping unused pinmux.
- Update imx6sl and imx6qdl device tree to assign corresponding clocks
instead of dummy clock.
- Update i.MX6/7 boards from NXP to assign corresponding power supply
for LDOs.
- Update i.MX6/7 device trees to enable SNVS poweroff key support
according to board design.
- Update coresight DT binding for i.MX7 according to consolidations
for CoreSight replicator and funnel.
- A series from Marek Vasut to update M53Menlo board on various devices
like UART, USB, ethernet PHY, GPIOs etc.
- Enable USBOTG support for imx7ulp and evk board.
- A series from Peter Robinson to update imx6sx-udoo board, switching
to SPDX License Identifier, enabling I2C devices and bluetooth
support.
- Add video capture support for i.MX53 and imx53-smd board.
- Add PXP device for i.MX6UL.
- Other random small updates on various boards.
* tag 'imx-dt-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (46 commits)
ARM: dts: imx7ulp-evk: enable USBOTG1 support
ARM: dts: imx7ulp: add imx7ulp USBOTG1 support
ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support
ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module
ARM: dts: imx7d-zii-rpu2: Drop unused pinmux entries
ARM: dts: imx7d-zii-rpu2: Fix incorrrect 'stdout-path'
ARM: dts: Add support for 96Boards Meerkat96 board
ARM: dts: imx6ul: Add PXP node
ARM: dts: imx6sll: Enable SNVS poweroff according to board design
ARM: dts: imx7s: Enable SNVS power key according to board design
ARM: dts: imx6sll: Enable SNVS power key according to board design
ARM: dts: imx6ul: Enable SNVS power key according to board design
ARM: dts: imx6sx: Enable SNVS power key according to board design
ARM: dts: imx6qdl: Enable SNVS power key according to board design
ARM: dts: imx53: Bind CPLD on M53Menlo
ARM: dts: Introduce the NXP LS1021A-TSN board
ARM: dts: imx6ull-colibri: enable UHS-I for USDHC1
ARM: dts: imx7d: Update cpufreq OPP table
ARM: dts: imx6sx-udoo-neo: add bluetooth config to uart3
ARM: dts: imx6sx-udoo-neo: enable i2c-2 and i2c-4 for onboard sensors
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Highlights:
----------
MPU part:
-Add stm32mp157a-avenger board support:
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
, 1024MB of DDR3 and STPMIC1A pmic . Several connections are available on this boards:
2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG, ethernet
10/100/1000, WiFi 5 GHz & 2.4GHz, ...
-Add STMFX support en stm32mp157c-ev1 and enable joystick connected on
it.
-Add I2S and SAI support on stm32mp157c.
-Add and enable support of Vivante GPU on stm32mp157 ED1 and DK1 boards
(EV1 and DK2 inherit of it).
-Add camera support:
-Add DCMI support on stm32mp157c SOC
-Enabled OV5640 camera support on stm32mp157c-ev1 board
-Enable hdmi bridge sii9022 & display controller on stm32mp157c-dk1
board.
MCU part:
-Add STMFX support en stm32746g-eval and enable connections on it:
leds and joystick
-----BEGIN PGP SIGNATURE-----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=3ZUA
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.3, round 1
Highlights:
----------
MPU part:
-Add stm32mp157a-avenger board support:
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
, 1024MB of DDR3 and STPMIC1A pmic . Several connections are available on this boards:
2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG, ethernet
10/100/1000, WiFi 5 GHz & 2.4GHz, ...
-Add STMFX support en stm32mp157c-ev1 and enable joystick connected on
it.
-Add I2S and SAI support on stm32mp157c.
-Add and enable support of Vivante GPU on stm32mp157 ED1 and DK1 boards
(EV1 and DK2 inherit of it).
-Add camera support:
-Add DCMI support on stm32mp157c SOC
-Enabled OV5640 camera support on stm32mp157c-ev1 board
-Enable hdmi bridge sii9022 & display controller on stm32mp157c-dk1
board.
MCU part:
-Add STMFX support en stm32746g-eval and enable connections on it:
leds and joystick
* tag 'stm32-dt-for-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (27 commits)
ARM: dts: stm32: replace rgmii mode with rgmii-id on stm32mp15 boards
ARM: dts: stm32: Add Avenger96 devicetree support based on STM32MP157A
dt-bindings: arm: stm32: Document Avenger96 devicetree binding
dt-bindings: arm: stm32: Convert STM32 SoC bindings to DT schema
ARM: dts: stm32: Add missing pinctrl definitions for STM32MP157
ARM: dts: stm32: add sai id registers to stm32mp157c
ARM: dts: stm32: add power supply of rm68200 on stm32mp157c-ev1
ARM: dts: stm32: enable display on stm32mp157c-dk1 board
ARM: dts: stm32: Add I2C 1 config for stm32mp157a-dk1
ARM: dts: stm32: enable OV5640 camera on stm32mp157c-ev1 board
ARM: dts: stm32: add DCMI pins to stm32mp157c
ARM: dts: stm32: add DCMI camera interface support on stm32mp157c
ARM: dts: stm32: enable Vivante GPU support on stm32mp157a-dk1 board
ARM: dts: stm32: enable Vivante GPU support on stm32mp157c-ed1 board
ARM: dts: stm32: Add Vivante GPU support on STM32MP157c
ARM: dts: stm32: add i2s pins muxing on stm32mp157
ARM: dts: stm32: add i2s support on stm32mp157c
ARM: dts: stm32: add sai pins muxing on stm32mp157
ARM: dts: stm32: add sai support on stm32mp157c
ARM: dts: stm32: add jedec compatible for nor flash on stm32mp157c-ev1
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add LCD support on Netgear RN104
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXQyyfAAKCRALBhiOFHI7
1ZPaAJ9AaFGTVnIuqe8EjZLOiKdO03oWMgCgm8Eu0d9566U2ibYCHCbHN0FbUpU=
=F0cP
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-5.3-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt for 5.3 (part 1)
Add LCD support on Netgear RN104
* tag 'mvebu-dt-5.3-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada: netgear-rn104: Add LCD to RN104 dts.
Signed-off-by: Olof Johansson <olof@lixom.net>
arm and arm64, a fix for the array syntax raised by our DT schemas.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXQyRegAKCRDj7w1vZxhR
xQ7SAP9gWeCGiyq+N2lvgFUOMVUezlDcJx2IVjoJvSQcyjeD2QD/W0m+fldHe7BB
PEv3s5BbYAYFHe+krqTPejcLK+c5hwg=
=4UQl
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-5.3-201906210812' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
This time we only have a single patch for our command branch between
arm and arm64, a fix for the array syntax raised by our DT schemas.
* tag 'sunxi-h3-h5-for-5.3-201906210812' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: h3/h5: Fix GPIO regulator state array
Signed-off-by: Olof Johansson <olof@lixom.net>
- Some work on the BPi M2-Berry to support various devices
- Convert some bindings to a schema, and a lot of fixes reported by
the schemas we introduced.
- A few other fixes here and there
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXQyQTgAKCRDj7w1vZxhR
xYkmAQDT7s1MRH9OEFQpS80BcWCvQoj0drr1ghHdXwwEbfuBUgEAoIuLrfH1Vjyi
ZcEJwPGowLmSEZezVWSLqTL76iajJg4=
=PAul
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.3-201906210807' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of patches:
- Some work on the BPi M2-Berry to support various devices
- Convert some bindings to a schema, and a lot of fixes reported by
the schemas we introduced.
- A few other fixes here and there
* tag 'sunxi-dt-for-5.3-201906210807' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (21 commits)
dt-bindings: pwm: Convert Allwinner PWM to a schema
ARM: dts: sun8i: r40: Change the RTC compatible
ARM: dts: sun8i: v3s: Add external crystals accuracy
ARM: dts: sun8i: v3s: Fix the RTC node
ARM: dts: sun6i: Add external crystals accuracy
ARM: dts: sun6i: Fix RTC node
ARM: dts: sun8i: a83t: Add device node for CSI (Camera Sensor Interface)
ARM: dts: gr8-evb: Fix RTC vendor
ARM: dts: sun7i: icnova-swac: Fix the model vendor
ARM: dts: sun8i: a711: Change LRADC node names to avoid warnings
ARM: dts: sun7i: olimex-lime2: Enable ac and power supplies
ARM: dts: sun6i: Add default address and size cells for SPI
ARM: dts: sun8i-h3: Fix wifi in Beelink X2 DT
dt-bindings: bus: Convert Allwinner RSB to a schema
ARM: dts: sun8i: r40: bananapi-m2-ultra: Remove regulator-always-on
ARM: dts: sun8i: v40: bananapi-m2-berry: Add Bluetooth device node
ARM: dts: sun8i: v40: bananapi-m2-berry: Enable AHCI
ARM: dts: sun8i: v40: bananapi-m2-berry: Enable HDMI output
ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC ethernet controller
ARM: dts: sun8i: v40: bananapi-m2-berry: Add GPIO pin-bank regulator supplies
...
Signed-off-by: Olof Johansson <olof@lixom.net>
We have various device tree updates from the OpenBMC project to enable
bits and pieces in existing systems, notably updates to Google's Zaius.
There are some AST2500 machines under development:
* Lenovo Hr630
* IBM Swift
* Facebook YAMP
And some AST2400 machines that have been around but out of tree and have
now joined the party:
* YADRO VESNIN
* Microsoft Olympus
-----BEGIN PGP SIGNATURE-----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=Hwcm
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.3-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/dt
ASPEED device tree updates for 5.3
We have various device tree updates from the OpenBMC project to enable
bits and pieces in existing systems, notably updates to Google's Zaius.
There are some AST2500 machines under development:
* Lenovo Hr630
* IBM Swift
* Facebook YAMP
And some AST2400 machines that have been around but out of tree and have
now joined the party:
* YADRO VESNIN
* Microsoft Olympus
* tag 'aspeed-5.3-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: Enable video engine on romulus and wtherspoon
ARM: dts: aspeed: Add Inspur fp5280g2 BMC machine
ARM: dts: aspeed: Add YADRO VESNIN BMC
ARM: dts: aspeed: Add Microsoft Olympus BMC
ARM: dts: aspeed: Adding Lenovo Hr630 BMC
ARM: dts: aspeed: Add Facebook YAMP BMC
ARM: dts: aspeed: swift: Add pca9539 devices
ARM: dts: aspeed: Add Swift BMC machine
ARM: dts: aspeed: cmm: enable ehci host controllers
ARM: dts: aspeed: zaius: fixed I2C bus numbers for pcie slots
ARM: dts: aspeed: zaius: update 12V brick I2C address
ARM: dts: aspeed: zaius: add Infineon and Intersil regulators
ARM: dts: aspeed: quanta-q71: Enable p2a node
ARM: dts: aspeed: Add aspeed-p2a-ctrl node
ARM: dts: aspeed: Add Power9 and Power9 CFAM description
ARM: dts: aspeed: Rename flash-controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add display support to MSM8974
* Add display, backlight, and touchscreen support to MSM8974 Hammerhead
* Update coresight bindings for MSM8974 and APQ8064
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q1ev
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm Device Tree Changes for v5.3
* Add display support to MSM8974
* Add display, backlight, and touchscreen support to MSM8974 Hammerhead
* Update coresight bindings for MSM8974 and APQ8064
* tag 'qcom-dts-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: msm8974-hammerhead: add support for display
ARM: dts: msm8974: add display support
ARM: dts: qcom: msm8974-hammerhead: add support for backlight
ARM: dts: qcom: msm8974-hammerhead: add touchscreen support
ARM: dts: qcom-msm8974: Update coresight DT bindings
ARM: dts: qcom-apq8064: Update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
- Updated CoreSight funnel and replicator using new bindings to fix warning
for the hip04.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJdCloiAAoJEAvIV27ZiWZcnLQP/Az5KoBhY1q9ve5jF/2vRKHU
/vWlNp9fYpndza5XGOTFa53/59mI/D7BWUKPcLZ9V9weof8dVD+IDffAZrNozUTs
anfvn2S7ZlpGxnSnNnDLELk2mAe9jq8JwCi/wPlkHcO7dn55LTREBSRJSDQJj9mg
5YZmSN/1DM0aw85/PB2P69r1Ri5VNGOpNMEWv8mZGt8DhKfeW0/UMv4r7pzrgkr7
MEyWopNoe/Ca0u6GjJWz4aSCgmI12IkXkZETYVGEvYnWHMZxzIaPXCuEnyo9aqvW
L8zMPtVF7yIJcnv2JR8Dwv3VS1b6amThQiHBq4oKWJjZrJzlOA3XHbvLdkwYTOkl
b2Xls0R/kgetHRoD27imIMMYL81Ftv3gyL8FV0zRybrKWL43tk5rYKgB/NXbZv3U
02M9jK5BQlnzDVdhg56UWK/Ish3JhbHMbDbUPB/X72eA/2wEb3qJeBrxsVwr6cJx
UmMOOL4TkKcP6KRGe0SNd6NhX4Go9H+3zlPAGrfU8pEMQF5FqW8BnThb50+AsWTk
EpwjMudBtAv8eNHbBQonN0VnB3OeWQQUP2B5B5/RT1NNxFG8UFvQdM5pWSKi29tD
wBmON4jJuwUdPbLbo9LaqEFA4w2IcSOPmvELc6d2t2fv4cFNScic9tITVmWQCZRs
cdgbu5cMFjqTs25G1zqB
=vaAE
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm32-dt-for-5.3' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM: DT: Hisilicon ARM32 SoCs updates for v5.3
- Updated CoreSight funnel and replicator using new bindings to fix warning
for the hip04.
* tag 'hisi-arm32-dt-for-5.3' of git://github.com/hisilicon/linux-hisi:
ARM: dts: hip04: Update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
- A recent testing by Sébastien discovers that the PWM interrupts of
i.MX6UL were wrongly coded in device tree. It's a fix for it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdEXKFAAoJEFBXWFqHsHzOnh4H/RVNWE/NwhLlcqXHnRq4TPpi
CdKQ9ZdXYWfi7SkFQJK8bYefklxfY7JUg4Pa/igTbkyeuwpHQugkYRK7is/jsEcd
TZSCllyvbn4QIOCZJiRsWd3/soEryjaQmZcHTVRLTJXZKhTPB89MuTX7j1BmGd22
SiSCTRtgVRWOY0ORF9oMtjNq1BiHEtf8M7GwvkifhlZCUh3pyqI7sqg+Zer/CEmM
TCOpDc42x56igw36/H/TMKyRQestYNlp8AKxg1cagwNrrLNE4D3Icm5UHdd44KuT
cS5O68BQxUldhfgdejfIZUvVguVlYQkuEZbCW/l18GdiK9IECW/xZRliBqO8RSw=
=Gn7a
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.2, round 3:
- A recent testing by Sébastien discovers that the PWM interrupts of
i.MX6UL were wrongly coded in device tree. It's a fix for it.
* tag 'imx-fixes-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6ul: fix PWM[1-4] interrupts
Signed-off-by: Olof Johansson <olof@lixom.net>
- fix GPU interrupts and operating voltage
-----BEGIN PGP SIGNATURE-----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=SdFR
-----END PGP SIGNATURE-----
Merge tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixes
ARM: dts: Amlogic fixes for v5.2-rc
- fix GPU interrupts and operating voltage
* tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8b: fix the operating voltage of the Mali GPU
ARM: dts: meson8b: drop undocumented property from the Mali GPU node
ARM: dts: meson8: fix GPU interrupts and drop an undocumented property
Signed-off-by: Olof Johansson <olof@lixom.net>
for 5.3 please pull the following:
- Lukas enables DMA support for the BCM2835 (Raspberry Pi) SPI
controller
- Florian fixes a number of dtc W=1 warnings in the Broadcom DTS files
and provides a fix for devices failing to boot after the removal of
skelton.dtsi (that commit has been submitted as a separate fix)
-----BEGIN PGP SIGNATURE-----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=AQ6F
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.3/devicetree-v2' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contain Broadcom ARM-based SoCs Device Tree changes
for 5.3 please pull the following:
- Lukas enables DMA support for the BCM2835 (Raspberry Pi) SPI
controller
- Florian fixes a number of dtc W=1 warnings in the Broadcom DTS files
and provides a fix for devices failing to boot after the removal of
skelton.dtsi (that commit has been submitted as a separate fix)
* tag 'arm-soc/for-5.3/devicetree-v2' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Fix most DTC W=1 warnings
ARM: dts: NSP: Fix the bulk of W=1 DTC warnings
ARM: dts: BCM63xx: Fix DTC W=1 warnings
ARM: dts: BCM53573: Fix DTC W=1 warnings
ARM: dts: bcm-mobile: Fix most DTC W=1 warnings
ARM: dts: Cygnus: Fix most DTC W=1 warnings
ARM: dts: Fix BCM7445 DTC warnings
ARM: bcm283x: Enable DMA support for SPI controller
ARM: dts: bcm: Add missing device_type = "memory" property
Signed-off-by: Olof Johansson <olof@lixom.net>
Add nodes for GPU (Mali 400) to Exynos4210 and Exynos4412. Describe the
GPU as much as possible however still few elements are missing:
1. Exynos4210 bus clock is not described in hardware manual therefore
the IP gate clock was provided,
2. Exynos4412: Not sure what to do with CLK_G3D clock responsible for
gating entire IP block (it is now being disabled as unused),
3. Regulator supplies on Trats board.
Limited testing on Odroid U3 (Exynos4412).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add nodes for GPU (Mali 400) to Exynos3250. This is still limited and
not tested:
1. No dynamic voltage and frequency scaling,
2. Not sure what to do with CLK_G3D clock responsible for gating entire
IP block (it is now being disabled as unused).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The eMMC memory is supplied by LDO18 (PVDD_EMMC_1V8) and buck10
(PVDD_EMMCF_2V8), not by LDO10. The LDO10 (PVDD_PRE_1V8) supplies
instead VDDP_MMC pin of eMMC host interface and it is already marked as
always on.
This change only properly models the hardware and reflects in usage of
regulators. There is no functional change because:
1. LDO18 cannot be turned off (e.g. by lack of consumers) because in
off mode it is controlled by LDO18EN pin, which is pulled up by
always-on regulator LDO2 (PVDD_APIO_1V8).
2. LDO10 is marked as always on so removing its consumer will not have
effect.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add the PMIC regulator suspend configuration to entire Odroid
XU3/XU4/HC1 family of boards to reduce power usage during suspend. The
configuration is based on vendor (Hardkernel) reference kernel with
additional buck9 suspend configuration (for USB hub suspend and proper
reset).
Energy consumption measurements from Marek Szyprowski during suspend to
RAM:
- all at 5 V power supply,
- before: next-20190620,
- after: next-20190620 + this patch + suspend configuration for s2mps11
regulator driver,
Board | before [mA] | after [mA] |
Odroid HC1 | 120 | 7-10 |
Odroid XU4, sdcard | 88 | 6-9 |
Odroid XU4, eMMC | 100 | 6-9 |
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Add the PMIC regulator suspend configuration to Arndale Octa board to
reduce power usage during suspend and keep necessary regulators on. The
configuration is based on vendor (Insignal) reference kernel and the
board datasheet. Comparing to vendor kernel, additionally turn off in
suspend all regulators controlled by external pin (LDO3, LDO7, LDO18 and
buck10).
This is purely for hardware description because board does not support
Suspend to RAM and the S2MPS11 driver does not support
"regulator-on-in-suspend" property.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The eMMC memory on Odroid XU3/XU4 boards is supplied by two regulators
LDO18 and buck10 (and LDO13 for the host interface).
However the Odroid HC1 board does not have eMMC connector so this
regulator does not have to be always on.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable USBOTG1 support for evk board, it is dual-role function
port.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The patch adds the following interfaces according the SMARC Spec 1.1
[1] and provided schematics:
- SMARC SPI0/1
Note: Since Kontron still uses silicon revisions below 1.3 they have
add a spi-nor to implement Workaround #1 of erratum ERR006282.
- SMARC SDIO
- SMARC LCD
- SMARC HDMI
- SMARC Management pins
Note: Kontron don't route all of these pins to the i.MX6, some are
routed to the SoM CPLD.
- SMARC GPIO
- SMARC CSI Camera
Note: As specified in [1] the data lanes are shared to cover the
csi and the parallel case. The case depends on the baseboard so
muxing the data lanes is not part of this patch.
- SMARC I2S
- SMARC Watchdog
Note: The watchdog output pin is routed to the CPLD and the SMARC
header. The CPLD performs a reset after a 30s timeout so we
need to enable the watchdog per default.
- SMARC module eeprom
Due to the lack of hardware not all of these interfaces are tesetd.
[1] https://sget.org/standards/smarc
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the i.MX6UL/L RM, table 3.1 "ARM Cortex A7 domain interrupt
summary", the interrupts for the PWM[1-4] go from 83 to 86.
Fixes: b9901fe84f ("ARM: dts: imx6ul: add pwm[1-4] nodes")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These settings are needed to make the hardware operable.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The PEN2 line needs to be pulled up for the charger to enter high-current
mode. Do this with a static pull on the GPIO.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The dock detection input key is active low. Also add a pinmux for it.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This allows users of the pinctrl driver to specify either
pinctrl-single,bias-pullup = MPF_PULL_UP;
or
pinctrl-single,bias-pulldown = MPF_PULL_DOWN;
To activate the pull bits in the MFP registers.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
SMARC-sAMX6i is a SMARC (Smart Mobility Architecture) compliant
module.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
warnings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes a number of unit_address_vs_reg warnings:
DTC arch/arm/boot/dts/bcm7445-bcm97445svmb.dtb
arch/arm/boot/dts/bcm7445.dtsi:66.6-225.4: Warning (unit_address_vs_reg): /rdb: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445.dtsi:227.21-298.4: Warning (unit_address_vs_reg): /memory_controllers: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445-bcm97445svmb.dts:9.9-14.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445.dtsi:255.10-275.5: Warning (simple_bus_reg): /memory_controllers/memc@1: simple-bus unit address format error, expected "80000"
arch/arm/boot/dts/bcm7445.dtsi:277.10-297.5: Warning (simple_bus_reg): /memory_controllers/memc@2: simple-bus unit address format error, expected "100000"
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Without this, the driver for the BCM2835 SPI controller uses interrupt
mode instead of DMA mode, incurring a significant performance penalty.
The Foundation's device tree has had these attributes for years, but for
some reason they were never upstreamed.
They were originally contributed by Noralf Trønnes and Martin Sperl:
https://github.com/raspberrypi/linux/commit/25f3e064afc8https://github.com/raspberrypi/linux/commit/e0edb52b47e6
The DREQ numbers 6 and 7 are documented in section 4.2.1.3 of:
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
On disco and eval board, Tx and Rx delay are applied (pull-up of 4.7k
put on VDD) so which correspond to RGMII-ID mode with internal RX and TX
delays provided by the PHY, the MAC should not add the RX or TX delays
in this case
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add devicetree support for Avenger96 board based on STM32MP157A MPU
from ST Micro. This board is one of the 96Boards Consumer Edition board
from Arrow Electronics and has the following features:
SoC: STM32MP157AAC
PMIC: STPMIC1A
RAM: 1024 Mbyte @ 533MHz
Storage: eMMC v4.51: 8 Gbyte
microSD Socket: UHS-1 v3.01
Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant
Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
Bluetooth®v4.2 (BR/EDR/BLE)
USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG
Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4
LED: 4x User LED, 1x WiFi LED, 1x BT LED
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add identification registers to address range
of SAI DT parent node, for stm32mp157c.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds a new property (power-supply) to panel rm68200 (raydium)
on stm32mp157c-ev1.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add CMT0 and CMT1 to the R-Car Gen2 V2H (r8a7792) SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit d6cd33ad71 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes: 9eb36b945b ("ARM: dts: iwg23s-sbc: Add uSD and eMMC support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tony Lindgren