Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
The recent patch ("kgdboc: Add kgdboc_earlycon to support early kgdb
using boot consoles") adds a new kernel command line parameter.
Document it.
Note that the patch adding the feature does some comparing/contrasting
of "kgdboc_earlycon" vs. the existing "ekgdboc". See that patch for
more details, but briefly "ekgdboc" can be used _instead_ of "kgdboc"
and just makes "kgdboc" do its normal initialization early (only works
if your tty driver is already ready). The new "kgdboc_earlycon" works
in combination with "kgdboc" and is backed by boot consoles.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.9.I7d5eb42c6180c831d47aef1af44d0b8be3fac559@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Allow users to build parameterized variants of fixtures.
If fixtures want variants, they call FIXTURE_VARIANT() to declare
the structure to fill for each variant. Each fixture will be re-run
for each of the variants defined by calling FIXTURE_VARIANT_ADD()
with the differing parameters initializing the structure.
Since tests are being re-run, additional initialization (steps,
no_print) is also added.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This kunit update for Linux-5.7-rc1 consists of:
- debugfs support for displaying kunit test suite results; this is
especially useful for module-loaded tests to allow disentangling of
test result display from other dmesg events. CONFIG_KUNIT_DEBUGFS
enables/disables the debugfs support.
- Several fixes and improvements to kunit framework and tool.
-----BEGIN PGP SIGNATURE-----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=5w9O
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kunit updates from Shuah Khan:
"This kunit update consists of:
- debugfs support for displaying kunit test suite results.
This is especially useful for module-loaded tests to allow
disentangling of test result display from other dmesg events.
CONFIG_KUNIT_DEBUGFS enables/disables the debugfs support.
- Several fixes and improvements to kunit framework and tool"
* tag 'linux-kselftest-kunit-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: tool: add missing test data file content
kunit: update documentation to describe debugfs representation
kunit: subtests should be indented 4 spaces according to TAP
kunit: add log test
kunit: add debugfs /sys/kernel/debug/kunit/<suite>/results display
Documentation: kunit: Make the KUnit documentation less UML-specific
Fix linked-list KUnit test when run multiple times
kunit: kunit_tool: Allow .kunitconfig to disable config items
kunit: Always print actual pointer values in asserts
kunit: add --make_options
kunit: Run all KUnit tests through allyesconfig
kunit: kunit_parser: make parser more robust
- Lots of RST conversion work by Mauro, Daniel ALmeida, and others.
Maybe someday we'll get to the end of this stuff...maybe...
- Some organizational work to bring some order to the core-api manual.
- Various new docs and additions to the existing documentation.
- Typo fixes, warning fixes, ...
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl6BLf4PHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YLhkIAIhcg6gxp0oZZ3KDfQyhvej0EWQGVDNkmloQ
O1VOSV3RJsZL9HwN9xSNnNfN5+hw5RUYVbn1s201uj6kovZY9qcTpHP2LCizUeGb
eFkSTmzkyAuAbJjuVLgMPDerJPEew0HnudiToeSpQeoIL1WB6YGd4/5H/cN1KLex
8ggjllcY0wOgbiFffmK6+tavDv7vT0lKTdwKRYh2nxu7zrPVVd1ZnW+RtntdTVQt
i+xwV6/YdWtg5C53IwBPpeyubX40vqaIjU8rzpLq5SCVbsZN14sSR709m1AYCOK0
i4VDWEhfA2XBi6Nycl5U0czuGziwoHrTgSCkS1mmSDujnpgfKM8=
=6YOS
-----END PGP SIGNATURE-----
Merge tag 'docs-5.7' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"This has been a busy cycle for documentation work.
Highlights include:
- Lots of RST conversion work by Mauro, Daniel ALmeida, and others.
Maybe someday we'll get to the end of this stuff...maybe...
- Some organizational work to bring some order to the core-api
manual.
- Various new docs and additions to the existing documentation.
- Typo fixes, warning fixes, ..."
* tag 'docs-5.7' of git://git.lwn.net/linux: (123 commits)
Documentation: x86: exception-tables: document CONFIG_BUILDTIME_TABLE_SORT
MAINTAINERS: adjust to filesystem doc ReST conversion
docs: deprecated.rst: Add BUG()-family
doc: zh_CN: add translation for virtiofs
doc: zh_CN: index files in filesystems subdirectory
docs: locking: Drop :c:func: throughout
docs: locking: Add 'need' to hardirq section
docs: conf.py: avoid thousands of duplicate label warning on Sphinx
docs: prevent warnings due to autosectionlabel
docs: fix reference to core-api/namespaces.rst
docs: fix pointers to io-mapping.rst and io_ordering.rst files
Documentation: Better document the softlockup_panic sysctl
docs: hw-vuln: tsx_async_abort.rst: get rid of an unused ref
docs: perf: imx-ddr.rst: get rid of a warning
docs: filesystems: fuse.rst: supress a Sphinx warning
docs: translations: it: avoid duplicate refs at programming-language.rst
docs: driver.rst: supress two ReSt warnings
docs: trace: events.rst: convert some new stuff to ReST format
Documentation: Add io_ordering.rst to driver-api manual
Documentation: Add io-mapping.rst to driver-api manual
...
Remove some of the outmoded "Why KUnit" rationale, and move some
UML-specific information to the kunit_tool page. Also update the Getting
Started guide to mention running tests without the kunit_tool wrapper.
Signed-off-by: David Gow <davidgow@google.com>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
* Don't list powerpc twice (once as ppc)
* Drop tile, which has been removed from the source tree
* Mention arm64, nds32, arc, and xtensa
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20200303194215.23756-1-j.neuschaefer@gmx.net
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fix a missing newline in a code block that was causing a warning:
Documentation/dev-tools/kunit/usage.rst:553: WARNING: Error in "code-block" directive:
maximum 1 argument(s) allowed, 3 supplied.
.. code-block:: bash
modprobe example-test
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This tag contains a handful of patches that I'd like to target for this merge
window:
* Support for kasan.
* 32-bit physical addresses on rv32i-based systems.
* Support for CONFIG_DEBUG_VIRTUAL
* DT entry for the FU540 GPIO controller, which has recently had a device
driver merged.
These boot a buildroot-based system on QEMU's virt board for me.
-----BEGIN PGP SIGNATURE-----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=W7f7
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.6-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains a handful of patches for this merge window:
- Support for kasan
- 32-bit physical addresses on rv32i-based systems
- Support for CONFIG_DEBUG_VIRTUAL
- DT entry for the FU540 GPIO controller, which has recently had a
device driver merged
These boot a buildroot-based system on QEMU's virt board for me"
* tag 'riscv-for-linus-5.6-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: dts: Add DT support for SiFive FU540 GPIO driver
riscv: mm: add support for CONFIG_DEBUG_VIRTUAL
riscv: keep 32-bit kernel to 32-bit phys_addr_t
kasan: Add riscv to KASAN documentation.
riscv: Add KASAN support
kasan: No KASAN's memmove check if archs don't have it.
Add riscv to the KASAN documentation to mention that riscv
is supporting generic kasan now.
Signed-off-by: Nick Hu <nickhu@andestech.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Documentation should describe how to build kunit and tests as
modules.
Co-developed-by: Knut Omang <knut.omang@oracle.com>
Signed-off-by: Knut Omang <knut.omang@oracle.com>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Make the layout of kcov_remote_arg the same for 32-bit and 64-bit code.
This makes it more convenient to write userspace apps that can be
compiled into 32-bit or 64-bit binaries and still work with the same
64-bit kernel.
Also use proper __u32 types in uapi headers instead of unsigned ints.
Link: http://lkml.kernel.org/r/9e91020876029cfefc9211ff747685eba9536426.1575638983.git.andreyknvl@google.com
Fixes: eec028c938 ("kcov: remote coverage support")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Marco Elver <elver@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: "Jacky . Cao @ sony . com" <Jacky.Cao@sony.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Marco Elver <elver@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit renames 'kunitconfig' to '.kunitconfig' so that it can be
automatically ignored by git and do not disturb people who want to type
'kernel/' by pressing only the 'k' and then 'tab' key.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The kunit doc suggests users to get the default `kunitconfig` from an
external git tree. However, the file is already located under the
`arch/um/configs/` of the kernel tree. Because the local file is easier
to access and maintain, this commit updates the doc to use it.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit c78fd76f2b ("selftests: Move kselftest_module.sh into
kselftest/") moved kselftest_module.sh but missed updating a few
references to the path in documentation.
Fixes: c78fd76f2b ("selftests: Move kselftest_module.sh into kselftest/")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add documentation for the Python script used to build, run, and collect
results from the kernel known as kunit_tool. kunit_tool
(tools/testing/kunit/kunit.py) was already added in previous commits.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Fix typos and gramatical errors in the Getting Started and Usage guide
for KUnit.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patchwork.kernel.org/patch/11156481/
Reported-by: Rinat Ibragimov <ibragimovrinat@mail.ru>
Link: https://github.com/google/kunit-docs/issues/1
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Patch series " kcov: collect coverage from usb and vhost", v3.
This patchset extends kcov to allow collecting coverage from backgound
kernel threads. This extension requires custom annotations for each of
the places where coverage collection is desired. This patchset
implements this for hub events in the USB subsystem and for vhost
workers. See the first patch description for details about the kcov
extension. The other two patches apply this kcov extension to USB and
vhost.
Examples of other subsystems that might potentially benefit from this
when custom annotations are added (the list is based on
process_one_work() callers for bugs recently reported by syzbot):
1. fs: writeback wb_workfn() worker,
2. net: addrconf_dad_work()/addrconf_verify_work() workers,
3. net: neigh_periodic_work() worker,
4. net/p9: p9_write_work()/p9_read_work() workers,
5. block: blk_mq_run_work_fn() worker.
These patches have been used to enable coverage-guided USB fuzzing with
syzkaller for the last few years, see the details here:
https://github.com/google/syzkaller/blob/master/docs/linux/external_fuzzing_usb.md
This patchset has been pushed to the public Linux kernel Gerrit
instance:
https://linux-review.googlesource.com/c/linux/kernel/git/torvalds/linux/+/1524
This patch (of 3):
Add background thread coverage collection ability to kcov.
With KCOV_ENABLE coverage is collected only for syscalls that are issued
from the current process. With KCOV_REMOTE_ENABLE it's possible to
collect coverage for arbitrary parts of the kernel code, provided that
those parts are annotated with kcov_remote_start()/kcov_remote_stop().
This allows to collect coverage from two types of kernel background
threads: the global ones, that are spawned during kernel boot in a
limited number of instances (e.g. one USB hub_event() worker thread is
spawned per USB HCD); and the local ones, that are spawned when a user
interacts with some kernel interface (e.g. vhost workers).
To enable collecting coverage from a global background thread, a unique
global handle must be assigned and passed to the corresponding
kcov_remote_start() call. Then a userspace process can pass a list of
such handles to the KCOV_REMOTE_ENABLE ioctl in the handles array field
of the kcov_remote_arg struct. This will attach the used kcov device to
the code sections, that are referenced by those handles.
Since there might be many local background threads spawned from
different userspace processes, we can't use a single global handle per
annotation. Instead, the userspace process passes a non-zero handle
through the common_handle field of the kcov_remote_arg struct. This
common handle gets saved to the kcov_handle field in the current
task_struct and needs to be passed to the newly spawned threads via
custom annotations. Those threads should in turn be annotated with
kcov_remote_start()/kcov_remote_stop().
Internally kcov stores handles as u64 integers. The top byte of a
handle is used to denote the id of a subsystem that this handle belongs
to, and the lower 4 bytes are used to denote the id of a thread instance
within that subsystem. A reserved value 0 is used as a subsystem id for
common handles as they don't belong to a particular subsystem. The
bytes 4-7 are currently reserved and must be zero. In the future the
number of bytes used for the subsystem or handle ids might be increased.
When a particular userspace process collects coverage by via a common
handle, kcov will collect coverage for each code section that is
annotated to use the common handle obtained as kcov_handle from the
current task_struct. However non common handles allow to collect
coverage selectively from different subsystems.
Link: http://lkml.kernel.org/r/e90e315426a384207edbec1d6aa89e43008e4caf.1572366574.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: David Windsor <dwindsor@gmail.com>
Cc: Elena Reshetova <elena.reshetova@intel.com>
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: Alexander Potapenko <glider@google.com>
Cc: Marco Elver <elver@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Various kerneldoc script enhancements.
- More RST conversions; those are slowing down as we run out of things to
convert, but we're a ways from done still.
- Dan's "maintainer profile entry" work landed at last. Now we just need
to get maintainers to fill in the profiles...
- A reworking of the parallel build setup to work better with a variety of
systems (and to not take over huge systems entirely in particular).
- The MAINTAINERS file is now converted to RST during the build.
Hopefully nobody ever tries to print this thing, or they will need to
load a lot of paper.
- A script and documentation making it easy for maintainers to add Link:
tags at commit time.
Also included is the removal of a bunch of spurious CR characters.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl3j5B0PHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YtBcH/jIN2cO8/0YW2rjVT+1G6ytSdFUKx5WJ/lpf
5uBeCvuCeYhtCB6+BgnXvjykJ7jDW11/NJNjWqz/gsvD5l5FJK1rXarI/oz2Klyi
kcPtDmBF/ki4wz9qXzEpa0vg8LXdjeys50S1vE75qCzxZoPP7YjuRbPnLrlIJukv
JbDVi4p9kxgeHfRB4+BHOe5rFwA3mMmaxKNIX34Y+UUO2KZ0g/yUi1bAaQwQAdt+
PsORmkVQ8Puh3K9xRIr7dYlcWBlBiPqzYdvDgTVxSjrxdK6wjYjSgVk2VjC5MBUN
mTSTWgyfsIcD/76/s8tq7ZRl2fw+SkCSkFo79Rb/hJwDTb7Vnng=
=LPBr
-----END PGP SIGNATURE-----
Merge tag 'docs-5.5a' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"Here are the main documentation changes for 5.5:
- Various kerneldoc script enhancements.
- More RST conversions; those are slowing down as we run out of
things to convert, but we're a ways from done still.
- Dan's "maintainer profile entry" work landed at last. Now we just
need to get maintainers to fill in the profiles...
- A reworking of the parallel build setup to work better with a
variety of systems (and to not take over huge systems entirely in
particular).
- The MAINTAINERS file is now converted to RST during the build.
Hopefully nobody ever tries to print this thing, or they will need
to load a lot of paper.
- A script and documentation making it easy for maintainers to add
Link: tags at commit time.
Also included is the removal of a bunch of spurious CR characters"
* tag 'docs-5.5a' of git://git.lwn.net/linux: (91 commits)
docs: remove a bunch of stray CRs
docs: fix up the maintainer profile document
libnvdimm, MAINTAINERS: Maintainer Entry Profile
Maintainer Handbook: Maintainer Entry Profile
MAINTAINERS: Reclaim the P: tag for Maintainer Entry Profile
docs, parallelism: Rearrange how jobserver reservations are made
docs, parallelism: Do not leak blocking mode to other readers
docs, parallelism: Fix failure path and add comment
Documentation: Remove bootmem_debug from kernel-parameters.txt
Documentation: security: core.rst: fix warnings
Documentation/process/howto/kokr: Update for 4.x -> 5.x versioning
Documentation/translation: Use Korean for Korean translation title
docs/memory-barriers.txt: Remove remaining references to mmiowb()
docs/memory-barriers.txt/kokr: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt/kokr: Fix style, spacing and grammar in I/O section
Documentation/kokr: Kill all references to mmiowb()
docs/memory-barriers.txt/kokr: Rewrite "KERNEL I/O BARRIER EFFECTS" section
docs: Add initial documentation for devfreq
Documentation: Document how to get links with git am
docs: Add request_irq() documentation
...
Patch series "kasan: support backing vmalloc space with real shadow
memory", v11.
Currently, vmalloc space is backed by the early shadow page. This means
that kasan is incompatible with VMAP_STACK.
This series provides a mechanism to back vmalloc space with real,
dynamically allocated memory. I have only wired up x86, because that's
the only currently supported arch I can work with easily, but it's very
easy to wire up other architectures, and it appears that there is some
work-in-progress code to do this on arm64 and s390.
This has been discussed before in the context of VMAP_STACK:
- https://bugzilla.kernel.org/show_bug.cgi?id=202009
- https://lkml.org/lkml/2018/7/22/198
- https://lkml.org/lkml/2019/7/19/822
In terms of implementation details:
Most mappings in vmalloc space are small, requiring less than a full
page of shadow space. Allocating a full shadow page per mapping would
therefore be wasteful. Furthermore, to ensure that different mappings
use different shadow pages, mappings would have to be aligned to
KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE.
Instead, share backing space across multiple mappings. Allocate a
backing page when a mapping in vmalloc space uses a particular page of
the shadow region. This page can be shared by other vmalloc mappings
later on.
We hook in to the vmap infrastructure to lazily clean up unused shadow
memory.
Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that:
- Turning on KASAN, inline instrumentation, without vmalloc, introuduces
a 4.1x-4.2x slowdown in vmalloc operations.
- Turning this on introduces the following slowdowns over KASAN:
* ~1.76x slower single-threaded (test_vmalloc.sh performance)
* ~2.18x slower when both cpus are performing operations
simultaneously (test_vmalloc.sh sequential_test_order=1)
This is unfortunate but given that this is a debug feature only, not the
end of the world. The benchmarks are also a stress-test for the vmalloc
subsystem: they're not indicative of an overall 2x slowdown!
This patch (of 4):
Hook into vmalloc and vmap, and dynamically allocate real shadow memory
to back the mappings.
Most mappings in vmalloc space are small, requiring less than a full
page of shadow space. Allocating a full shadow page per mapping would
therefore be wasteful. Furthermore, to ensure that different mappings
use different shadow pages, mappings would have to be aligned to
KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE.
Instead, share backing space across multiple mappings. Allocate a
backing page when a mapping in vmalloc space uses a particular page of
the shadow region. This page can be shared by other vmalloc mappings
later on.
We hook in to the vmap infrastructure to lazily clean up unused shadow
memory.
To avoid the difficulties around swapping mappings around, this code
expects that the part of the shadow region that covers the vmalloc space
will not be covered by the early shadow page, but will be left unmapped.
This will require changes in arch-specific code.
This allows KASAN with VMAP_STACK, and may be helpful for architectures
that do not have a separate module space (e.g. powerpc64, which I am
currently working on). It also allows relaxing the module alignment
back to PAGE_SIZE.
Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that:
- Turning on KASAN, inline instrumentation, without vmalloc, introuduces
a 4.1x-4.2x slowdown in vmalloc operations.
- Turning this on introduces the following slowdowns over KASAN:
* ~1.76x slower single-threaded (test_vmalloc.sh performance)
* ~2.18x slower when both cpus are performing operations
simultaneously (test_vmalloc.sh sequential_test_order=3D1)
This is unfortunate but given that this is a debug feature only, not the
end of the world.
The full benchmark results are:
Performance
No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN
fix_size_alloc_test 662004 11404956 17.23 19144610 28.92 1.68
full_fit_alloc_test 710950 12029752 16.92 13184651 18.55 1.10
long_busy_list_alloc_test 9431875 43990172 4.66 82970178 8.80 1.89
random_size_alloc_test 5033626 23061762 4.58 47158834 9.37 2.04
fix_align_alloc_test 1252514 15276910 12.20 31266116 24.96 2.05
random_size_align_alloc_te 1648501 14578321 8.84 25560052 15.51 1.75
align_shift_alloc_test 147 830 5.65 5692 38.72 6.86
pcpu_alloc_test 80732 125520 1.55 140864 1.74 1.12
Total Cycles 119240774314 763211341128 6.40 1390338696894 11.66 1.82
Sequential, 2 cpus
No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN
fix_size_alloc_test 1423150 14276550 10.03 27733022 19.49 1.94
full_fit_alloc_test 1754219 14722640 8.39 15030786 8.57 1.02
long_busy_list_alloc_test 11451858 52154973 4.55 107016027 9.34 2.05
random_size_alloc_test 5989020 26735276 4.46 68885923 11.50 2.58
fix_align_alloc_test 2050976 20166900 9.83 50491675 24.62 2.50
random_size_align_alloc_te 2858229 17971700 6.29 38730225 13.55 2.16
align_shift_alloc_test 405 6428 15.87 26253 64.82 4.08
pcpu_alloc_test 127183 151464 1.19 216263 1.70 1.43
Total Cycles 54181269392 308723699764 5.70 650772566394 12.01 2.11
fix_size_alloc_test 1420404 14289308 10.06 27790035 19.56 1.94
full_fit_alloc_test 1736145 14806234 8.53 15274301 8.80 1.03
long_busy_list_alloc_test 11404638 52270785 4.58 107550254 9.43 2.06
random_size_alloc_test 6017006 26650625 4.43 68696127 11.42 2.58
fix_align_alloc_test 2045504 20280985 9.91 50414862 24.65 2.49
random_size_align_alloc_te 2845338 17931018 6.30 38510276 13.53 2.15
align_shift_alloc_test 472 3760 7.97 9656 20.46 2.57
pcpu_alloc_test 118643 132732 1.12 146504 1.23 1.10
Total Cycles 54040011688 309102805492 5.72 651325675652 12.05 2.11
[dja@axtens.net: fixups]
Link: http://lkml.kernel.org/r/20191120052719.7201-1-dja@axtens.net
Link: https://bugzilla.kernel.org/show_bug.cgi?id=3D202009
Link: http://lkml.kernel.org/r/20191031093909.9228-2-dja@axtens.net
Signed-off-by: Mark Rutland <mark.rutland@arm.com> [shadow rework]
Signed-off-by: Daniel Axtens <dja@axtens.net>
Co-developed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This kselftest update for Linux 5.5-rc1 adds KUnit, a lightweight unit
testing and mocking framework for the Linux kernel from Brendan Higgins.
KUnit is not an end-to-end testing framework. It is currently supported
on UML and sub-systems can write unit tests and run them in UML env.
KUnit documentation is included in this update.
In addition, this Kunit update adds 3 new kunit tests:
- kunit test for proc sysctl from Iurii Zaikin
- kunit test for the 'list' doubly linked list from David Gow
- ext4 kunit test for decoding extended timestamps from Iurii Zaikin
In the future KUnit will be linked to Kselftest framework to provide
a way to trigger KUnit tests from user-space.
-----BEGIN PGP SIGNATURE-----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=0zEe
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.5-rc1-kunit' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest KUnit support gtom Shuah Khan:
"This adds KUnit, a lightweight unit testing and mocking framework for
the Linux kernel from Brendan Higgins.
KUnit is not an end-to-end testing framework. It is currently
supported on UML and sub-systems can write unit tests and run them in
UML env. KUnit documentation is included in this update.
In addition, this Kunit update adds 3 new kunit tests:
- proc sysctl test from Iurii Zaikin
- the 'list' doubly linked list test from David Gow
- ext4 tests for decoding extended timestamps from Iurii Zaikin
In the future KUnit will be linked to Kselftest framework to provide a
way to trigger KUnit tests from user-space"
* tag 'linux-kselftest-5.5-rc1-kunit' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (23 commits)
lib/list-test: add a test for the 'list' doubly linked list
ext4: add kunit test for decoding extended timestamps
Documentation: kunit: Fix verification command
kunit: Fix '--build_dir' option
kunit: fix failure to build without printk
MAINTAINERS: add proc sysctl KUnit test to PROC SYSCTL section
kernel/sysctl-test: Add null pointer test for sysctl.c:proc_dointvec()
MAINTAINERS: add entry for KUnit the unit testing framework
Documentation: kunit: add documentation for KUnit
kunit: defconfig: add defconfigs for building KUnit tests
kunit: tool: add Python wrappers for running KUnit tests
kunit: test: add tests for KUnit managed resources
kunit: test: add the concept of assertions
kunit: test: add tests for kunit test abort
kunit: test: add support for test abort
objtool: add kunit_try_catch_throw to the noreturn list
kunit: test: add initial tests
lib: enable building KUnit in lib/
kunit: test: add the concept of expectations
kunit: test: add assertion printing library
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl2su/AeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGvm4H/1jkheCrvB/GJS69
wd18vizAg+eFmNCzxlGVhpQTKGymNRy+g6clnoli3cNJ3pSVKcYgVyB3oXaONIhp
g/ANudnBjTdjqYgJzfLij5AGecrGwDpF3YL0kuKrCB63s2I/HwQGYy/aPrYY8emy
gAYdaf1DGRu5/DIIB6soTo/TnpKoAyTE+XY5MaPSug++t/Flov19tlU40IZxXW94
bjTXbm0yklrsIx+LL5mYYGGnygSTCF66JjFg1qhDCBQaS2MZ21h1ZgaOtGZTwZcc
WgEiqLC5S1Iyj96zir1t78RcVQ4RzgvDbhUOgIqUFsYAO2wOicvxyFE3Hj8rPOKd
uGgVPRM=
=xgZa
-----END PGP SIGNATURE-----
Merge tag 'v5.4-rc4' into docs-next
I need to pick up the independent changes made to
Documentation/core-api/memory-allocation.rst to be able to merge further
work without creating a total mess.
Commit 8974558f49 ("mm, page_owner, debug_pagealloc: save and dump
freeing stack trace") enhanced page_owner to also store freeing stack
trace, when debug_pagealloc is also enabled. KASAN would also like to
do this [1] to improve error reports to debug e.g. UAF issues.
Kirill has suggested that the freeing stack trace saving should be also
possible to be enabled separately from KASAN or debug_pagealloc, i.e.
with an extra boot option. Qian argued that we have enough options
already, and avoiding the extra overhead is not worth the complications
in the case of a debugging option. Kirill noted that the extra stack
handle in struct page_owner requires 0.1% of memory.
This patch therefore enables free stack saving whenever page_owner is
enabled, regardless of whether debug_pagealloc or KASAN is also enabled.
KASAN kernels booted with page_owner=on will thus benefit from the
improved error reports.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=203967
[vbabka@suse.cz: v3]
Link: http://lkml.kernel.org/r/20191007091808.7096-3-vbabka@suse.cz
Link: http://lkml.kernel.org/r/20190930122916.14969-3-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Qian Cai <cai@lca.pw>
Suggested-by: Dmitry Vyukov <dvyukov@google.com>
Suggested-by: Walter Wu <walter-zh.wu@mediatek.com>
Suggested-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Suggested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Suggested-by: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kunit wrapper script ('kunit.py') receives a sub-command (only 'run' for
now) as its argument. If no sub-command is given, it prints help
message and just quit. However, an example command in the kunit
documentation for a verification of kunit is missing the sub-command.
This commit fixes the example.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Let the user specify an optional TARGETS skiplist through the new optional
SKIP_TARGETS Makefile variable.
It is easier to skip at will using a reduced and well defined list of
possibly problematic targets with SKIP_TARGETS than to provide a partially
stripped down list of good targets using the usual TARGETS variable.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit c566586818 ("mm: kmemleak: use the memory pool for early
allocations") renamed CONFIG_DEBUG_KMEMLEAK_EARLY_LOG_SIZE to
CONFIG_DEBUG_KMEMLEAK_MEM_POOL_SIZE. Update the documentation reference
to reflect that.
Fixes: c566586818 ("mm: kmemleak: use the memory pool for early allocations")
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add documentation for KUnit, the Linux kernel unit testing framework.
- Add intro and usage guide for KUnit
- Add API reference
Signed-off-by: Felix Guo <felixguoxiuping@gmail.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This fell into disrepair a while ago, and the majority of hits to the
snapshots were from bots, so it's more trouble to keep running than it's worth.
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the latex_documents are handled automatically, we can
remove those extra conf.py files.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Wikipedia now has a main article to "tracing garbage collector" topic.
Change the URL and use the reStructuredText syntax for hyperlinks and add
more details about the use of the tool. Add a section about how to use
the kmemleak-test module to test the memory leak scanning.
Link: http://lkml.kernel.org/r/20190612155231.19448-2-andrealmeid@collabora.com
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Document some things of note to gcov users:
1. GCC gcov and Clang llvm-cov tools are not compatible.
2. The use of GCC vs Clang is transparent at build-time.
Also adjust the documentation to account for the removal of config symbol
CONFIG_GCOV_FORMAT_AUTODETECT by commit 6a61b70b43 ("gcov: remove
CONFIG_GCOV_FORMAT_AUTODETECT").
Link: http://lkml.kernel.org/r/20190318025411.98014-4-trong@android.com
Signed-off-by: Tri Vo <trong@android.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Daniel Mentz <danielmentz@google.com>
Cc: Greg Hackmann <ghackmann@android.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Petri Gynther <pgynther@google.com>
Cc: Prasad Sodagudi <psodagud@quicinc.com>
Cc: Trilok Soni <tsoni@quicinc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Lots of work on the Chinese and Italian translations
- Some license-rules clarifications from Christoph
- Various build-script fixes
- A new document on memory models
- RST conversion of the live-patching docs
- The usual collection of typo fixes and corrections.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAlzSBFkPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YUDgIAIn+I0Wjv/vkuh5SKwAmz2wZBf46FCICz7Vg
jePmhd1GQ3K9k/xzIKMoaJOipAl+IXT4AnGa9eu+9Xm+D6HejASvtt/uTce4+qPi
9VLu7GmbtQQ0imRi4jjitenrebQXSKudAYbH+/bz7ycH7twWVJWKNLNQ8im9U5Ul
LRXQhRsYc2SwJ4mGOGTrqZkb69qkiOy0dQFGKbSM3ipHs/CQy8XMhlY/7aAh7t9N
SmKyH341s4Z/dRZIpoSx2QOfSp7njwTw7hxrnOq5unB82u2zrYvVFGxp5kzfQIyC
B/q26TG5hVNGH/37/+yOoziyP3Ma8IuF5W0zcg9DbmIi0Gdvg7s=
=4Zhc
-----END PGP SIGNATURE-----
Merge tag 'docs-5.2' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"A reasonably busy cycle for docs, including:
- Lots of work on the Chinese and Italian translations
- Some license-rules clarifications from Christoph
- Various build-script fixes
- A new document on memory models
- RST conversion of the live-patching docs
- The usual collection of typo fixes and corrections"
* tag 'docs-5.2' of git://git.lwn.net/linux: (140 commits)
docs/livepatch: Unify style of livepatch documentation in the ReST format
docs: livepatch: convert docs to ReST and rename to *.rst
scripts/documentation-file-ref-check: detect broken :doc:`foo`
scripts/documentation-file-ref-check: don't parse Next/ dir
LICENSES: Rename other to deprecated
LICENSES: Clearly mark dual license only licenses
docs: Don't reference the ZLib license in license-rules.rst
docs/vm: Minor editorial changes in the THP and hugetlbfs
docs/vm: add documentation of memory models
doc:it_IT: translation alignment
doc: fix typo in PGP guide
dontdiff: update with Kconfig build artifacts
docs/zh_CN: fix typos in 1.Intro.rst file
docs/zh_CN: redirect CoC docs to Chinese version
doc: mm: migration doesn't use FOLL_SPLIT anymore
docs: doc-guide: remove the extension from .rst files
doc: kselftest: Fix KBUILD_OUTPUT usage instructions
docs: trace: fix some Sphinx warnings
docs: speculation.txt: mark example blocks as such
docs: ntb.txt: add blank lines to clean up some Sphinx warnings
...
Fix KBUILD_OUTPUT usage instructions. The current documentation is
incorrect. Update and fix outdated information about summary option.
Add a reference to kselftest wiki for additional information on the
framework and tips on writing new tests.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
kselftest runs as a userspace process. Sometimes we need to test things
from kernel space. One way of doing this is by creating a test module.
Currently doing so requires developers to write a bunch of boiler plate
in the module if kselftest is to be used to run the tests. This means
we currently have a load of duplicate code to achieve these ends. If we
have a uniform method for implementing test modules then we can reduce
code duplication, ensure uniformity in the test framework, ease code
maintenance, and reduce the work required to create tests. This all
helps to encourage developers to write and run tests.
Add a C header file that can be included in test modules. This provides
a single point for common test functions/macros. Implement a few macros
that make up the start of the test framework.
Add documentation for new kselftest header to kselftest documentation.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Shuah Khan <shuah@kernel.org>
svn commit 231296 matches commit d29e939c63b71 ("Add fuzzing coverage
support") in the gcc git. The change is part of gcc 6.1.0.
Replace the svn commit number with a gcc version which everyone can
easily compare.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
document on perf security, more Italian translations, more
improvements to the memory-management docs, improvements to the
pathname lookup documentation, and the usual array of smaller
fixes.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAlwmSPkPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Y9ZoH/joPnMFykOxS0SmdfI7Z+F4EiJct/ZwF9bHx
T673T0RC30IgnUXGmBl5OtktfWqVh9aGqHOGwgh65ybp2QvzemdP0k6Lu6RtwNk9
6LfkpvuUb8FzaQmCHnSMzMSDmXtZUw3Z/mOjCBcQtfGAsUULNT08xl+Dr+gwWIWt
H+gPEEP+MCXTOQO1jm2dHOHW8NGm6XOijMTpOxp/pkoEY5tUxkVB1T//8EeX7LVh
c1QHzFrufE3bmmubCLtIuyVqZbm/V5l6rHREDQ46fnH/G9fM4gojzsrAL/Y2m4bt
E4y0XJHycjLMRDimAnYhbPm1ryTFAX1lNzHP3M/EF6Heqx8YHAk=
=vtwu
-----END PGP SIGNATURE-----
Merge tag 'docs-5.0' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"A fairly normal cycle for documentation stuff. We have a new document
on perf security, more Italian translations, more improvements to the
memory-management docs, improvements to the pathname lookup
documentation, and the usual array of smaller fixes.
As is often the case, there are a few reaches outside of
Documentation/ to adjust kerneldoc comments"
* tag 'docs-5.0' of git://git.lwn.net/linux: (38 commits)
docs: improve pathname-lookup document structure
configfs: fix wrong name of struct in documentation
docs/mm-api: link slab_common.c to "The Slab Cache" section
slab: make kmem_cache_create{_usercopy} description proper kernel-doc
doc:process: add links where missing
docs/core-api: make mm-api.rst more structured
x86, boot: documentation whitespace fixup
Documentation: devres: note checking needs when converting
doc🇮🇹 add some process/* translations
doc🇮🇹 fixes in process/1.Intro
Documentation: convert path-lookup from markdown to resturctured text
Documentation/admin-guide: update admin-guide index.rst
Documentation/admin-guide: introduce perf-security.rst file
scripts/kernel-doc: Fix struct and struct field attribute processing
Documentation: dev-tools: Fix typos in index.rst
Correct gen_init_cpio tool's documentation
Document /proc/pid PID reuse behavior
Documentation: update path-lookup.md for parallel lookups
Documentation: Use "while" instead of "whilst"
dmaengine: Add mailing list address to the documentation
...
This patch updates KASAN documentation to reflect the addition of the new
tag-based mode.
Link: http://lkml.kernel.org/r/aabef9de317c54b8a3919a4946ce534c6576726a.1544099024.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some documents are refering to others without links. With this
patch I add those missing links.
This patch affects only documents under process/ and labels where
necessary.
Signed-off-by: Federico Vaga <federico.vaga@vaga.pv.it>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fixes a spelling error and removes an extra whitespace character.
Signed-off-by: Shreyans Devendra Doshi <0xinfosect0r@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This is a small cleanup to kselftest.rst:
- Fix some language typos in the usage instructions.
- Change one non-ASCII space to an ASCII space.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
* Fix install instruction by adding `./autogen` command
before `./configure`.
* Add link to a more detailed installation instruction.
* Add link to SmPL grammar documentation.
* Add single space after ',' to slightly improve readability.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Config fragment files should be placed in
tools/testing/selftests/<testdir>/config
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add a description that kernel config options should be added into a
config file that is placed next to the newly added test.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add a description that the kernel headers should be used as far as it is
possible and then the system headers.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Mike Rapoport says:
These patches convert files in Documentation/vm to ReST format, add an
initial index and link it to the top level documentation.
There are no contents changes in the documentation, except few spelling
fixes. The relatively large diffstat stems from the indentation and
paragraph wrapping changes.
I've tried to keep the formatting as consistent as possible, but I could
miss some places that needed markup and add some markup where it was not
necessary.
[jc: significant conflicts in vm/hmm.rst]
- Lots of work aligning Documentation/ABI with reality, done by Aishwarya
Pant.
- The trace documentation has been converted to RST by Changbin Du
- I thrashed up kernel-doc to deal with a parsing issue and to try to make
the code more readable. It's still a 20+-year-old Perl hack, though.
- Lots of other updates, typo fixes, and more.
-----BEGIN PGP SIGNATURE-----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=QQ/a
-----END PGP SIGNATURE-----
Merge tag 'docs-4.17' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"There's been a fair amount of activity in Documentation/ this time
around:
- Lots of work aligning Documentation/ABI with reality, done by
Aishwarya Pant.
- The trace documentation has been converted to RST by Changbin Du
- I thrashed up kernel-doc to deal with a parsing issue and to try to
make the code more readable. It's still a 20+-year-old Perl hack,
though.
- Lots of other updates, typo fixes, and more"
* tag 'docs-4.17' of git://git.lwn.net/linux: (82 commits)
Documentation/process: update FUSE project website
docs: kernel-doc: fix parsing of arrays
dmaengine: Fix spelling for parenthesis in dmatest documentation
dmaengine: Make dmatest.rst indeed reST compatible
dmaengine: Add note to dmatest documentation about supported channels
Documentation: magic-numbers: Fix typo
Documentation: admin-guide: add kvmconfig, xenconfig and tinyconfig commands
Input: alps - Update documentation for trackstick v3 format
Documentation: Mention why %p prints ptrval
COPYING: use the new text with points to the license files
COPYING: create a new file with points to the Kernel license files
Input: trackpoint: document sysfs interface
xfs: Change URL for the project in xfs.txt
char/bsr: add sysfs interface documentation
acpi: nfit: document sysfs interface
block: rbd: update sysfs interface
Documentation/sparse: fix typo
Documentation/CodingStyle: Add an example for braces
docs/vm: update 00-INDEX
kernel-doc: Remove __sched markings
...
Linus Torvalds