This is a driver for VMware's paravirtualized SCSI device,
which should improve disk performance for guests running
under control of VMware hypervisors that support such devices.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This driver supports PMC-Sierra PCIe SAS/SATA 8x6G SPC 8001 chip based
host adapters.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
[v2: fixed up virt_to_bus() issue spotted by sfr]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
People keep sending patches to expose CONFIG_SCSI_WAIT_SCAN as a tunable
item. These patches aren't accepted upstream, so let's stop the ongoing
irritation of people due to the unconditionally installed module and its
Kconfig symbol.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
New iSCSI driver for Broadcom BNX2 devices. The driver interfaces with
the CNIC driver to access the hardware.
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I had to set CONFIG_SCSI_MULTI_LUN to y in order to get my SE W595
working when plugging it as a mass storage. Looking at SCSI option to
get a phone behaving correctly was convoluted to say the least. There
are quite a few other reports about USB card readers needing this option
as well. This patch improves the help text to make the use of the option
more obvious.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Zero functional changes, just file movement.
This commit prepares for the upcoming integration of the
Marvell-provided driver update that splits the driver into support
for both 64xx and 94xx chip families.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
fnic is a driver for the Cisco PCI-Express FCoE HBA
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mention ATAPI. We could insert an essay about libata and ide-scsi etc but
the failure case is someone enables it which is just fine so keep it
simple.
(Revised text from suggestion by Matthew Wilcox)
Closes#7736
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Just sets up build environment for libfcoe module towards a
libfcoe library for libfc LLDs using FCoE as libfc transport.
Common library code to libfcoe is added in next patch.
Also, updated MODULE_LICENSE from "GPL" string to "GPL v2" for
libfc, libfcoe and fcoe modules to accurately match the licenses.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* This is new scsi lld device driver from LSI supporting the SAS 2.0
standard. I have split patchs by filename.
* Here is list of new 6gb host controllers:
LSI SAS2004
LSI SAS2008
LSI SAS2108
LSI SAS2116
* Here are the changes in the 4th posting of this patch set:
(1) fix compile errors when SCSI_MPT2SAS_LOGGING is not enabled
(2) add mpt2sas to the SCSI Mid Layer Makefile
(3) append mpt2sas_ to the naming of all non-static functions
(4) fix oops for SMP_PASSTHRU
(5) doorbell algorithm imported changes from windows driver
* Here are the changes in the 3rd posting of this patch set:
(1) add readl following writel from the function that disables interrupts
(2) replace 0xFFFFFFFFFFFFFFFFULL with ~0ULL
(3) when calling pci_enable_msix, only pass one msix entry (instead of 15).
(4) remove the "current HW implementation uses..... " comment in the sources
(5) merged bug fix for SIGIO/POLLIN notifcation; reported by the storlib team.
* Here are the changes in the 2nd posting of this patch set:
(1) use little endian types in the mpi headers
(2) merged in bug fix's from inhouse drivers.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Tested-by: peter Bogdanovic <pbog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
OSD in kernel source code is assumed to be at:
drivers/scsi/osd/ with its own Makefile and Kconfig
Add includes to them from drivers/scsi Makefile and Kconfig
Add OSD to MAINTAINERS file
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Kconfig entry for SCSI_LOGGING refers the reader to
drivers/scsi/scsi.c, but I didn't find any useful information
there. There is certainly logging code in that file, but the
logging types and logging levels are described in
drivers/scsi/scsi_logging.h.
Also, the procfs file referred to in the section is incorrect.
It should be /proc/sys/dev/scsi/logging_level and not
/proc/scsi/scsi.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
libfc uses crc32 functions, so cause it to be built
via select:
drivers/built-in.o: In function `fc_frame_crc_check':
(.text+0x75dae): undefined reference to `crc32_le'
drivers/built-in.o: In function `fc_fcp_recv':
fc_fcp.c:(.text+0x7b919): undefined reference to `crc32_le'
fc_fcp.c:(.text+0x7b9d5): undefined reference to `crc32_le'
fc_fcp.c:(.text+0x7ba54): undefined reference to `crc32_le'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix scsi_debug build error:
drivers/built-in.o: In function `resp_read':
scsi_debug.c:(.text+0x21379a): undefined reference to `crc_t10dif'
drivers/built-in.o: In function `resp_write':
scsi_debug.c:(.text+0x213fca): undefined reference to `crc_t10dif'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iSeries dependent drivers fail to build, when CONFIG_VIOPATH is disabled.
Fix the problem by making those drivers select it.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As planed, this removes ide-scsi.
The 2.6 kernel supports direct writing to ide CD drives, which
eliminates the need for ide-scsi. ide-scsi has been unmaintained and
marked as deprecated.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James.Bottomley@HansenPartnership.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
fcoe selects libfc and requires SCSI and PCI (the SCSI requirement is
implicitly covered by an enclosing if). Fix them both up so they
cannot be configured in an invalid state: make LIBFC select
SCSI_FC_ATTRS and make FCOE depend on PCI and select LIBFC.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch implements the cxgb3i iscsi connection acceleration for the
open-iscsi initiator.
The cxgb3i driver offers the iscsi PDU based offload:
- digest insertion and verification
- payload direct-placement into host memory buffer.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Encapsulation protocol for running Fibre Channel over Ethernet interfaces.
Creates virtual Fibre Channel host adapters using libfc.
This layer is the LLD to the scsi-ml. It allocates the Scsi_Host, utilizes
libfc for Fibre Channel protocol processing and interacts with netdev to
send/receive Ethernet packets.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
libFC is composed of 4 blocks supported by an exchange manager
and a framing library. The upper 4 layers are fc_lport, fc_disc,
fc_rport and fc_fcp. A LLD that uses libfc could choose to
either use libfc's block, or using the transport template
defined in libfc.h, override one or more blocks with its own
implementation.
The EM (Exchange Manager) manages exhcanges/sequences for all
commands- ELS, CT and FCP.
The framing library frames ELS and CT commands.
The fc_lport block manages the library's representation of the
host's FC enabled ports.
The fc_disc block manages discovery of targets as well as
handling changes that occur in the FC fabric (via. RSCN events).
The fc_rport block manages the library's representation of other
entities in the FC fabric. Currently the library uses this block
for targets, its peer when in point-to-point mode and the
directory server, but can be extended for other entities if
needed.
The fc_fcp block interacts with the scsi-ml and handles all
I/O.
Signed-off-by: Robert Love <robert.w.love@intel.com>
[jejb: added include of delay.h to fix ppc64 compile prob spotted by sfr]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch removes the Hades support that was marked as BROKEN 5 years ago.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This option was forgotten when the SCSI_QLOGIC_FC driver was removed.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Support for controllers and disks that implement DIF protection
information:
- During command preparation the RDPROTECT/WRPROTECT must be set
correctly if the target has DIF enabled.
- READ(6) and WRITE(6) are not supported when DIF is on.
- The controller must be told how to handle the I/O via the
protection operation field in scsi_cmnd.
- Refactor the I/O completion code that extracts failed LBA from the
returned sense data and handle DIF failures correctly.
- sd_dif.c implements the functions required to prepare and complete
requests with protection information attached.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds a new device driver to support the Virtual Fibre Channel
interface on IBM Power based servers. The Virtual I/O Server on IBM Power
servers utilizes N-Port ID Virtualization to export a Virtual Fibre Channel
adapter to the client. This driver is the client device driver.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The module name was changed from esp to sun_esp some time ago.
Also correct the list of chips supported by the driver.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some of the storage devices (that can be accessed through multiple paths),
do need some special handling for
1. Activating the passive path of the storage access.
2. Decode and handle the special sense codes returned by the devices.
3. Handle the I/Os being sent to the passive path, especially
during the device probe time.
when accessed through multiple paths.
As of today this special device handling is done at the dm-multipath
layer using dm-handlers. That works well for (1); for (2) to be handled
at dm layer, scsi sense information need to be exported from SCSI to dm-layer,
which is not very attractive; (3) cannot be done at all at the dm layer.
Device handler has been moved to SCSI mainly to handle (2) and (3) properly.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The new mac_esp scsi driver needs CONFIG_SCSI_SPI_ATTRS, just like all other
drivers using the new esp_scsi core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the code to actually support 64 bit platforms. 64 bit
DMA is enabled on both x86_32 PAE and 64 bit platforms.
This code is based in part on the unofficial adaptec 64-bit
dpt_i2o driver update that I got from Mark Salyzyn at Adaptec.
Signed-off-by: Miquel van Smoorenburg <miquels@cistron.nl>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Replace the mac_esp driver with a new one based on the esp_scsi core.
For esp_scsi: add support for sync transfers for the PIO mode, add a new
esp_driver_ops method to get the maximum dma transfer size (like the old
NCR53C9x driver), and some cleanups.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We've verified that there are 64 bit and endianness problems in the
flashpoint driver. Reverse the logic of CONFIG_OMIT_FLASHPOINT (make
it CONFIG_SCSI_FLASHPOINT) and make it depend on X86_32 so it can't
appear for any other architectures. Long term, if someone chooses,
they could make FlashPoint 64 bit compliant (it looks like its a
question of fixing up the sizes in some of the packed descriptors)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We have several drivers that don't list SCSI as a dependency in
Kconfig. That leads to them potentially being selected as Y even if
SCSI is M (which will produce a build failure). Fix this by making
the if SCSI_LOWLEVEL that goes around all the drivers a tristate
forcing them all automatically to inherit the value of SCSI.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix compilation warning in gdth.c, which was using the deprecated
pci_find_device.
drivers/scsi/gdth.c:645: warning: 'pci_find_device' is deprecated (declared at include/linux/pci.h:495)
Changing it to use pci_get_device, instead.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds support to SCSI for enclosure services devices. It also makes
use of the enclosure services added in an earlier patch to display the
enclosure topology in sysfs.
At the moment, the enclosures are SAS specific, but if anyone actually
has a non-SAS enclosure that follows the SES-2 standard, we can add that
as well.
On my Vitesse based system, the enclosures show up like this:
sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/
total 0
-r--r--r-- 1 root root 4096 2008-02-03 15:44 components
lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004
drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005
lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure
--w------- 1 root root 4096 2008-02-03 15:44 uevent
And the individual occupied slots like this:
sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/
total 0
-rw-r--r-- 1 root root 4096 2008-02-03 15:45 active
lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0
-rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault
-rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate
-rw-r--r-- 1 root root 4096 2008-02-03 15:45 status
lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component
-r--r--r-- 1 root root 4096 2008-02-03 15:45 type
--w------- 1 root root 4096 2008-02-03 15:45 uevent
You can flash the various blinky lights by echoing to the fault and locate files.
>From the device's point of view, you can see it has an enclosure like this:
sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/
block:sda generic queue_depth state
bsg:0:0:0:0 iocounterbits queue_type subsystem
bus iodone_cnt rescan timeout
delete ioerr_cnt rev type
device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent
driver modalias scsi_disk:0:0:0:0 vendor
enclosure_component:SLOT 001 model scsi_generic:sg0
evt_media_change power scsi_level
Note the enclosure_component:SLOT 001 which shows where in the enclosure
this device fits.
The astute will notice that I'm using SCSI VPD Inquiries to identify the
devices. This, unfortunately, won't work for SATA devices unless we do
some really nasty hacking about on the SAT because the only think that
knows the SAS addresses for SATA devices is libsas, not libata where the
SAT resides.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
These drivers depend on the deprecated NCR53C9X core and need to be converted
to the esp_scsi core.
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Linux/m68k <linux-m68k@vger.kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This driver depends on the deprecated NCR53C9X core and needs to be converted
to the esp_scsi core.
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This driver depends on the deprecated NCR53C9X core and needs to be converted
to the esp_scsi core.
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Converted sun3x_esp driver to use esp_scsi.c
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SGI IP28 machines would need special treatment (enable adding addtional
wait states) when accessing memory uncached. To avoid this pain I
changed the driver to use only cached access to memory.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
Fix typo in arch/powerpc/boot/flatdevtree_env.h.
There is no Documentation/networking/ixgbe.txt.
README.cycladesZ is now in Documentation/.
wavelan.p.h is now in drivers/net/wireless/.
HFS.txt is now Documentation/filesystems/hfs.txt.
OSS-files are now in sound/oss/.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use open-iscsi.org instead of linux-iscsi.sf.net, which hasn't been
updated for ages.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Most code changes were made to support adapters based on Marvell IOP, plus some
other fixes.
- add more PCI device IDs
- support for adapters based on Marvell IOP
- fix a result code translation error on big-endian systems
- fix resource releasing bug when scsi_host_alloc() fail in hptiop_probe()
- update scsi_cmnd.resid when finishing a request
- correct some coding style issues
[akpm@linux-foundation.org: type fixes]
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Apparently no one wonts this driver, and no one
is willing to fix it for future changes to SCSI.
So remove it, and if someone wants it in the future
He can revive it with the needed fixes.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The psi240i driver is still written for cmnd->request_buffer
as a char pointer to actual data. There was never any attempt
to use the scatterlist option.
- remove all source files (3) from drivers/scsi
- Remove from Makefile and Kconfig
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix links to files in Documentation/* in various Kconfig files
Signed-off-by: Dirk Hohndel <hohndel@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change PortAddr to be an unsigned int instead of an unsigned short (IO
Port address are 24 bit on parisc). Fix a couple of printk argument
warnings. Remove the Kconfig marking as 'BROKEN'.
I haven't removed the #warning yet because virt_to_bus/bus_to_virt are
only eliminated for narrow boards. Wide boards need more work.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Description:
** support ARC1200/1201/1202 SATA RAID adapter, which is named
ACB_ADAPTER_TYPE_B
** modify the arcmsr_pci_slot_reset function
** modify the arcmsr_pci_ers_disconnect_forepart function
** modify the arcmsr_pci_ers_need_reset_forepart function
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds minimum target driver support like the srp transport does:
- fc_remote_port_{rolechg,delete} calls
scsi_tgt_it_nexus_{create,destroy} for target drivers.
- add callbacks to notify target drivers of the nexus and tmf
operation results to fc_function_template.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
it's better to remove tgt dependencies in srp transport class since
most people want only initiator support.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This converts libsrp and ibmvstgt to use srp transport.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds minimum target driver support:
- srp_rport_{add,del} calls scsi_tgt_it_nexus_{create,destroy} for
target drivers.
- add a callback to notify target drivers of the nexus operation
results to srp_function_template.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This converts ibmvscsi to use the srp transport class.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds srp transport class that works with ib_srp and ibmvscsi.
It creates only /sys/class/{srp_host,srp_remote_ports} and
srp_remote_ports has only "port_id" attribute.
viola:/sys/class/srp_remote_ports/port-0:1# ls
device port_id subsystem uevent
viola:/sys/class/srp_remote_ports/port-0:1# cat port_id
4c:49:4e:55:58:20:56:49:4f:00:00:00:00:00:00:00
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Introduce CONFIG_CHECK_SIGNATURE to control inclusion of check_signature()
and avoid problems on platforms that don't have readb().
Let the few legacy (ISA || PCI || X86) drivers that need check_signature()
select CONFIG_CHECK_SIGNATURE.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m68k: Fix a few hickups in drivers/scsi/Kconfig
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sas transport class attaches one bsg device to every SAS object
(host, device, expander, etc). LLDs can define a function to handle
SMP requests via sas_function_template::smp_handler.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu",
so that the user can disable all the options in that menu at once
instead of having to disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make some offending drivers depend on it and set CONFIG_ARCH_NO_VIRT_TO_BUS
for ppc64 so that we don't build those drivers.
This gets PowerPC allmodconfig and allyesconfig much closer to building.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@ftp.linux.org.uk>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
Not converted to the 2.6 kconfig system and no code in the tree.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With
dma-mapping-prevent-dma-dependent-code-from-linking-on.patch
scsi fails to build on !HAS_DMA architectures:
drivers/built-in.o(.text+0x20af6): In function `scsi_dma_map':
: undefined reference to `dma_map_sg'
drivers/built-in.o(.text+0x20b5c): In function `scsi_dma_unmap':
: undefined reference to `dma_unmap_sg'
I split those functions out into a new file. Builds on s390 and i386.
Move scsi_dma_{map,unmap} into scsi_lib_dma.c which is only build if
HAS_DMA is set.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Mon, 11 Jun 2007 20:28:16 +0200 api wrote:
> Good day,
> When doing make menuconfig one comes across CONFIG_BLK_DEV_SD.
> The help file states that this is for scsi disks.NO MENTION IS MADE THAT
> IT IS NEEDE FOR SATA DISKS AS WELL!
> Would have saved me a lot of time if the help was up to date.
> I hope this can be changed so others can make a kernel for sata systems
> quicker.
From: Randy Dunlap <randy.dunlap@oracle.com>
Add help info for BLK_DEV_SD referring to its use in
SATA or PATA driver configurations.
Add help text for "ATA" indicating that it probably needs
some SCSI config symbols enabled in order to be useful.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
New driver for Amiga Zorro bus NCR53c710 SCSI controllers, using the 53c700
SCSI core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New driver for the Amiga 4000T built-in NCR53c710 SCSI controller, using the
53c700 SCSI core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New driver for the MVME16x NCR53C710 SCSI controller, using the 53c700 SCSI
core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New driver for the BVME6000 NCR53C710 SCSI controller, using the 53c700 SCSI
core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add m68k support to the 53c700 SCSI driver
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/jazz_esp.c
Same changes made by both SCSI and SPARC trees: problem with UTF-8
conversion in the copyright.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is basically a straight conversion. I have one of these things, so
I know it works ... my problem is that it has a wierd SCA like
connector, so I can't connect anything to it (no cables).
However, previously it panic'd in the interrupt, now it completes a bus
scan.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
kconfig: fix mconf segmentation fault
kbuild: enable use of code from a different dir
kconfig: error out if recursive dependencies are found
kbuild: scripts/basic/fixdep segfault on pathological string-o-death
kconfig: correct minor typo in Kconfig warning message.
kconfig: fix path to modules.txt in Kconfig help
usr/Kconfig: fix typo
kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
kbuild: be more explicit on missing .config file
kbuild: clarify the creation of the LOCALVERSION_AUTO string.
kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
kconfig: refer to qt3 if we cannot find qt libraries
kbuild: handle compressed cpio initramfs-es
kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
kbuild: remove stale comment in modpost.c
kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
kbuild: fix make mrproper for Documentation/DocBook/man
kbuild: remove kconfig binaries during make mrproper
kconfig/menuconfig: do not hardcode '.config'
kbuild: override build timestamp & version
...
SCSI should be working on a TT (but someone should really try!) but causes
trouble on a Falcon (as in: it ate a filesystem of mine) at least when
used concurrently with IDE. I have the notion it's because locking of the
ST-DMA interrupt by IDE is broken in 2.6 (the IDE driver always complains
about trying to release an already-released ST-DMA). Needs more work, but
that's on the IDE or m68k interrupt side rather than SCSI.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation/modules.txt doesn't exist, but
Documentation/kbuild/modules.txt does.
Signed-off-by: Alexander E. Patrakov
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Major features:
1) Tagged queuing support.
2) Will properly negotiate for synchronous transfers even on
devices that reject the wide negotiation message, such as
CDROMs
3) Significantly lower kernel stack usage in interrupt
handler path by elimination of function vector arrays,
replaced by a top-level switch statement state machine.
4) Uses generic scsi infrastructure as much as possible to
avoid code duplication.
5) Automatic request of sense data in response to CHECK_CONDITION
6) Portable to other platforms using ESP such as DEC and Sun3
systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unused SCSI-related kernel config variables
SCSI_NCR53C8XX_PROFILE_SUPPORT
SCSI_NCR53C8XX_PROFILE
53C700_IO_MAPPED
AIC79XX_ENABLE_RD_STRM
AIC7XXX_PROBE_EISA_VL
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently scsi_wait_scan is only built modular if SCSI is modular.
However, it's perfectly possible for a built in SCSI still to have
modular drivers and thus need scsi_wait_scan as a module. Therefore,
scsi_wait_scan should always be built as a module (unless the kernel
doesn't support modules).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Apparently the driver compiles and runs, so tidy up some macro warnings
and bring it back as unBROKEN.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make sun3 scsi drivers compile/work again (though with way too many warnings...)
Tested on 3/50, 3/60.
Signed-off-by: Sam Creasey <sammy@sammy.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- add comments for various devices
- remove unused device ids(0xf350, 0x4301, 0x8301, 0x8302)
- add new device id(0xe350)
- fix vendor id of st_vsc
- modify Kconfig help info
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is IBM Virtual SCSI target driver for tgt. The driver is based on
the original ibmvscsis driver:
http://lkml.org/lkml/2005/10/17/99
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
libsrp provides helper functions for SRP target drivers.
Some SRP target drivers would be out of drivers/scsi/ so we added an
entry for libsrp in drivers/scsi/Kconfig.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Makefile and Kconfig for tgt.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Without this patch, the user has to add a kernel command line parameter
to get asynchronous SCSI scanning. Now they can select the default at
compile time and still override it at boot time if they need to.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Both SCSI_IPR_TRACE and SCSI_IPR_DUMP should be defaulted to
yes when SCSI_IPR is enabled.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Randy brought it to my attention that in proper english "can not" should always
be written "cannot". I donot see any reason to argue, even if I mightnot
understand why this rule exists. This patch fixes "can not" in several
Documentation files as well as three Kconfigs.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Adds support to attach SATA devices to ipr SAS adapters.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
CONFIG_SCSI_NETLINK can become a bool since the item its
selecting (CONFIG_NET) cannot be a module.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch formally adds support for the posting of FC events via netlink.
It is a followup to the original RFC at:
http://marc.theaimsgroup.com/?l=linux-scsi&m=114530667923464&w=2
and the initial posting at:
http://marc.theaimsgroup.com/?l=linux-scsi&m=115507374832500&w=2
The patch has been updated to optimize the send path, per the discussions
in the initial posting.
Per discussions at the Storage Summit and at OLS, we are to use netlink for
async events from transports. Also per discussions, to avoid a netlink
protocol per transport, I've create a single NETLINK_SCSITRANSPORT protocol,
which can then be used by all transports.
This patch:
- Creates new files scsi_netlink.c and scsi_netlink.h, which contains the
single and shared definitions for the SCSI Transport. It is tied into the
base SCSI subsystem intialization.
Contains a single interface routine, scsi_send_transport_event(), for a
transport to send an event (via multicast to a protocol specific group).
- Creates a new scsi_netlink_fc.h file, which contains the FC netlink event
messages
- Adds 3 new routines to the fc transport:
fc_get_event_number() - to get a FC event #
fc_host_post_event() - to send a simple FC event (32 bits of data)
fc_host_post_vendor_event() - to send a Vendor unique event, with
arbitrary amounts of data.
Note: the separation of event number allows for a LLD to send a standard
event, followed by vendor-specific data for the event.
Note: This patch assumes 2 prior fc transport patches have been installed:
http://marc.theaimsgroup.com/?l=linux-scsi&m=115555807316329&w=2http://marc.theaimsgroup.com/?l=linux-scsi&m=115581614930261&w=2
Sorry - next time I'll do something like making these individual
patches of the same posting when I know they'll be posted closely
together.
Signed-off-by: James Smart <James.Smart@emulex.com>
Tidy up configuration not to make SCSI always select NET
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add Promise SuperTrak 'stex' driver, supporting SuperTrak
EX8350/8300/16350/16300 controllers. The controller's firmware accepts
SCSI commands, handing them to the underlying RAID or JBOD disks.
The driver consisted of the following cleanups and fixes, beyond its
initial submission:
Ed Lin:
stex: cleanup and minor fixes
stex: add new device ids
stex: update internal copy code path
stex: add hard reset function
stex: adjust command timeout in slave_config routine
stex: use more efficient method for unload/shutdown flush
Jeff Garzik:
[SCSI] Add Promise SuperTrak 'shasta' driver.
Rename drivers/scsi/shasta.c to stex.c ("SuperTrak EX").
[SCSI] stex: update with community comments from 'Promise SuperTrak' thread
[SCSI] stex: Fix warning, trim trailing whitespace.
[SCSI] stex: remove last remnants of "shasta" project code name
[SCSI] stex: removed 6-byte command emulation
[SCSI] stex: minor cleanups
[SCSI] stex: minor fixes: irq flag, error return value
[SCSI] stex: use dma_alloc_coherent()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the end point of the separate aic94xx driver based on the
original driver and transport class from Luben Tuikov
<ltuikov@yahoo.com>
The log of the separate development is:
Alexis Bruemmer:
o aic94xx: fix hotplug/unplug for expanderless systems
o aic94xx: disable split completion timer/setting by default
o aic94xx: wide port off expander support
o aic94xx: remove various inline functions
o aic94xx: use bitops
o aic94xx: remove queue comment
o aic94xx: remove sas_common.c
o aic94xx: sas remove depot's
o aic94xx: use available list_for_each_entry_safe_reverse()
o aic94xx: sas header file merge
James Bottomley:
o aic94xx: fix TF_TMF_NO_CTX processing
o aic94xx: convert to request_firmware interface
o aic94xx: fix hotplug/unplug
o aic94xx: add link error counts to the expander phys
o aic94xx: add transport class phy reset capability
o aic94xx: remove local_attached flag
o Remove README
o Fixup Makefile variable for libsas rename
o Rename sas->libsas
o aic94xx: correct return code for sas_discover_event
o aic94xx: use parent backlink port
o aic94xx: remove channel abstraction
o aic94xx: fix routing algorithms
o aic94xx: add backlink port
o aic94xx: fix cascaded expander properties
o aic94xx: fix sleep under lock
o aic94xx: fix panic on module removal in complex topology
o aic94xx: make use of the new sas_port
o rename sas_port to asd_sas_port
o Fix for eh_strategy_handler move
o aic94xx: move entirely over to correct transport class formulation
o remove last vestages of sas_rphy_alloc()
o update for eh_timed_out move
o Preliminary expander support for aic94xx
o sas: remove event thread
o minor warning cleanups
o remove last vestiges of id mapping arrays
o Further updates
o Convert aic94xx over entirely to the transport class end device and
o update aic94xx/sas to use the new sas transport class end device
o [PATCH] aic94xx: attaching to the sas transport class
o Add missing completion removal from prior patch
o [PATCH] aic94xx: attaching to the sas transport class
o Build fixes from akpm
Jeff Garzik:
o [scsi aic94xx] Remove ->owner from PCI info table
Luben Tuikov:
o initial aic94xx driver
Mike Anderson:
o aic94xx: fix panic on module insertion
o aic94xx: stub out SATA_DEV case
o aic94xx: compile warning cleanups
o aic94xx: sas_alloc_task
o aic94xx: ref count update
o aic94xx nexus loss time value
o [PATCH] aic94xx: driver assertion in non-x86 BIOS env
Randy Dunlap:
o libsas: externs not needed
Robert Tarte:
o aic94xx: sequence patch - fixes SATA support
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
arcmsr is a driver for the Areca Raid controller, a host based RAID
subsystem that speaks SCSI at the firmware level.
This patch is quite a clean up over the initial submission with
contributions from:
Randy Dunlap <rdunlap@xenotime.net>
Christoph Hellwig <hch@lst.de>
Matthew Wilcox <matthew@wil.cx>
Adrian Bunk <bunk@stusta.de>
Signed-off-by: Erich Chen <erich@areca.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ata_piix's Kconfig entry still refers only to ICH5, while it supports ICH6
through 8. This creates confusion with people who are looking to see
if their newer SATA enabled motherboards are supported. The
following patch makes this clear.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: trivial fixes in Makefile
kbuild: adding symbols in Kconfig and defconfig to TAGS
kbuild: replace abort() with exit(1)
kbuild: support for %.symtypes files
kbuild: fix silentoldconfig recursion
kbuild: add option for stripping modules while installing them
kbuild: kill some false positives from modpost
kbuild: export-symbol usage report generator
kbuild: fix make -rR breakage
kbuild: append -dirty for updated but uncommited changes
kbuild: append git revision for all untagged commits
kbuild: fix module.symvers parsing in modpost
kbuild: ignore make's built-in rules & variables
kbuild: bugfix with initramfs
kbuild: modpost build fix
kbuild: check license compatibility when building modules
kbuild: export-type enhancement to modpost.c
kbuild: add dependency on kernel.release to the package targets
kbuild: `make kernelrelease' speedup
kconfig: KCONFIG_OVERWRITECONFIG
...
HighPoint RocketRAID 3220/3320 series 8 channel PCI-X SATA RAID Host
Adapters.
Fixes from original submission:
Merge Andrew Morton's patches:
- Provide locking for global list
- Fix debug printks
- uninline function with multiple callsites
- coding style fixups
- remove unneeded casts of void*
- kfree(NULL) is legal
- Don't "succeed" if register_chrdev() failed - otherwise we'll later
unregister a not-registered chrdev.
- Don't return from hptiop_do_ioctl() with the spinlock held.
- uninline __hpt_do_ioctl()
Update for Arjan van de Ven's comments:
- put all asm/ includes after the linux/ ones
- replace mdelay with msleep
- add pci posting flush
- do not set pci command reqister in map_pci_bar
- do not try merging sg elements in hptiop_buildsgl()
- remove unused outstandingcommands member from hba structure
- remove unimplemented hptiop_abort() handler
- remove typedef u32 hpt_id_t
Other updates:
- fix endianess
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This removes all the leading whitespace kconfig now warns about.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Let people enable the advansys driver on x86-32, even though it's broken
on other architectures due to missing DMA mapping infrastructure.
It's used by Jeffrey Phillips Freeman <jeffreyfreeman@syncleus.com> and
possibly others.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most of the Kconfig options for switching between IO Port and MMIO
operations use the opposite sense from sym2. Really, this option
should be set at a chipset level rather than per-driver.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Most of the text by Mark Salyzyn <mark_salyzyn@adaptec.com>.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Make drivers that use directly PC parport HW depend on PARPORT_PC rather than
HW independent PARPORT.
Signed-off-by: Marko Kohtala <marko.kohtala@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
scsi_print_msg() is an SPI-specific concept. This patch moves it from
constants.c to scsi_transport_spi.c and updates the Kconfig to link in
the SPI class for the drivers which use scsi_print_msg().
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SCSI qlogicisp driver is both marked BROKEN and superseded by the
qla1280 driver.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hopefully there should be a brand new replacement driver for this heap
of junk by the beginning of next year.
Acked By: Martin K. Petersen <mkp@mkp.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This change makes quirk_intel_ide_combined() dependent on the precise
conditions under which it is needed:
* IDE is built in
* IDE SATA option is not set
* ata_piix or ahci drivers are enabled
This fixes an issue where some modular configurations would not cause
the quirk to be enabled.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus torvalds <torvalds@osdl.org>
Now it looks like we'll have multiple users of the iscsi transport
class, the iscsi initiator shouldn't really be a dependency of it. This
patch moves iscsi to being an initiator in its own right which selects
the transport attributes.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SAS transport class contains common code to deal with SAS HBAs, an
aproximated representation of SAS topologies in the driver model,
and various sysfs attributes to expose these topologies and managment
interfaces to userspace.
In addition to the basic SCSI core objects this transport class introduces
two additional intermediate objects: The SAS PHY as represented by struct
sas_phy defines an "outgoing" PHY on a SAS HBA or Expander, and the SAS
remote PHY represented by struct sas_rphy defines an "incoming" PHY on a
SAS Expander or end device. Note that this is purely a software concept, the
underlying hardware for a PHY and a remote PHY is the exactly the same.
There is no concept of a SAS port in this code, users can see what PHYs
form a wide port based on the port_identifier attribute, which is the same
for all PHYs in a port.
This submission doesn't handle hot-plug addition or removal of SAS devices
and thus doesn't do scanning in a workqueue yet, that will be added in
phase2 after this submission. In a third phase I will add additional
managment infrastructure.
I think this submission is ready for 2.6.14, but additional comments are
of course very welcome.
I'd like to thanks James Smart a lot for his very useful input on the
design.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is my libata compatible low level driver for the Marvell SATA
family. Currently it successfully runs in PIO mode on a 6081 chip.
EDMA support is in the works and should be done shortly. Review,
testing (especially on other flavors of Marvell), comments welcome.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The idea behind a RAID class is to provide a uniform interface to all
RAID subsystems (both hardware and software) in the kernel.
To do that, I've made this class a transport class that's entirely
subsystem independent (although the matching routines have to match per
subsystem, as you'll see looking at the code). I put it in the scsi
subdirectory purely because I needed somewhere to play with it, but it's
not a scsi specific module.
I used a fusion raid card as the test bed for this; with that kind of
card, this is the type of class output you get:
jejb@titanic> ls -l /sys/class/raid_devices/20\:0\:0\:0/
total 0
lrwxrwxrwx 1 root root 0 Aug 16 17:21 component-0 -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:1:0/20:1:0:0/
lrwxrwxrwx 1 root root 0 Aug 16 17:21 component-1 -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:1:1/20:1:1:0/
lrwxrwxrwx 1 root root 0 Aug 16 17:21 device -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:0:0/20:0:0:0/
-r--r--r-- 1 root root 16384 Aug 16 17:21 level
-r--r--r-- 1 root root 16384 Aug 16 17:21 resync
-r--r--r-- 1 root root 16384 Aug 16 17:21 state
So it's really simple: for a SCSI device representing a hardware raid,
it shows the raid level, the array state, the resync % complete (if the
state is resyncing) and the underlying components of the RAID (these are
exposed in fusion on the virtual channel 1).
As you can see, this type of information can be exported by almost
anything, including software raid.
The more difficult trick, of course, is going to be getting it to
perform configuration type actions with writable attributes.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Alok Kataria