Since "wireless-regdb: remove antenna gain" was merged in the
wireless-regdb tree, the awk script parser has been incompatible
with the 'official' regulatory database. This fixes that up.
Without this change the max EIRP is set to 0 making 802.11 devices
useless.
The fragile nature of the awk parser must be replaced, but ideas
over how to do that in the most scalable way are being reviewed.
In the meantime update the documentation for CFG80211_INTERNAL_REGDB
so folks are aware of expectations for now.
Reported-by: John Walker <john@x109.net>
Reported-by: Krishna Chaitanya <chaitanya.mgit@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some VHT TDLS peers (Google Nexus 5) include the VHT-AID IE in their
TDLS setup request/response. Usermode passes this aid as the station
aid, causing it to fail verifiction, since this happens in the
"set_station" stage. Make an exception for the TDLS use-case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
tsc can be NULL (mac80211 currently always passes NULL),
resulting in NULL-dereference. check before copying it.
Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Driver is now responsible for veryfing if the
switch is possible.
Since this is inherently tricky driver may decide
to disconnect an interface later with
cfg80211_stop_iface().
This doesn't mean driver can accept everything. It
should do it's best to verify requests and reject
them as soon as possible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The non-split wiphy state shouldn't be increased in size
so move the new set_qos_map command into the split if
statement.
Cc: stable@vger.kernel.org (3.14+)
Fixes: fa9ffc7456 ("cfg80211: Add support for QoS mapping")
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
MAX_JIFFY_OFFSET has no meaning when calculating the
elapsed jiffies, as jiffies run out until ULONG_MAX.
This miscalculation results in erroneous values
in case of a wrap-around.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 8eca1fb692.
Felix notes that this broke regulatory, leaving channel 12 open for AP
operation in the US regulatory domain where it isn't permitted.
Link: http://mid.gmane.org/53A6C0FF.9090104@openwrt.org
Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, cfg80211 tries to implement ethtool, but that doesn't
really scale well, with all the different operations. Make the
lower-level driver responsible for it, which currently only has
an effect on mac80211. It will similarly not scale well at that
level though, since mac80211 also has many drivers.
To cleanly implement this in mac80211, introduce a new file and
move some code to appropriate places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Generalize the power conversion from mW to dBm
using log. This should fix the below compilation
error for country NO which adds a new power value
2000mW which is not handled earlier.
CC [M] net/wireless/wext-sme.o
CC [M] net/wireless/regdb.o
net/wireless/regdb.c:1130:1: error: Unknown undeclared here (not in
a function)
net/wireless/regdb.c:1130:9: error: expected } before power
make[2]: *** [net/wireless/regdb.o] Error 1
make[1]: *** [net/wireless] Error 2
make: *** [net] Error 2
Reported-By: John Walker <john@x109.net>
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
[remove unneeded parentheses, fix rounding by using %.0f]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're currently sending NEW_WIPHY events for renames (which
is a bit odd, but now can't be changed), but also send them
for really new devices that register.
Also send DEL_WIPHY events when a device is removed, the
event ID for this was already reserved.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channels in 2.4GHz band overlap, this means that if we
send a probe request on channel 1 and then move to channel
2, we will hear the probe response on channel 2. In this
case, the RSSI will be lower than if we had heard it on
the channel on which it was sent (1 in this case).
The firmware / low level driver can parse the channel in
the DS IE or HT IE and compensate the RSSI so that it will
still have a valid value even if we heard the frame on an
adjacent channel. This can be done up to a certain offset.
Add this offset as a configuration for the low level driver.
A low level driver that can compensate the low RSSI in this
case should assign the maximal offset for which the RSSI
value is still valid.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise every "indoor" setting by usermode will cause a regdomain reset.
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement and export the new cfg80211_get_station() API.
This utility can be used by other kernel modules to obtain
detailed information about a given wireless station.
It will be in particular useful to batman-adv which will
implement a wireless rate based metric.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Users may need information about the expected throughput
towards a given peer.
This value is supposed to consider the size overhead
generated by the 802.11 header.
This value is exported in kbps through the get_station() API
by including it into the station_info object.
Moreover, it is sent to user space when replying to the
nl80211 GET_STATION command.
This information will be useful to the batman-adv module
which will use it for its new metric computation.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This requires changing the nl80211 parsing code a bit to use
intermediate pointers for the allocation, but clarifies the
API towards the drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This also propagates through the drivers.
The orinoco driver uses the cfg80211 API structs for internal
bookkeeping, and so needs a (void *) cast that removes the
const - but that's OK because it allocates those pointers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the type of NL80211_ATTR_CSA_C_OFF_BEACON and
NL80211_ATTR_CSA_C_OFF_PRESP to be NLA_BINARY which allows
userspace to use beacons and probe responses with
multiple CSA counters.
This isn't breaking the API since userspace can
continue to use nla_put_u16 for this attributes, which
is equivalent to a single element u16 array.
In addition advertise max number of supported CSA counters.
This is needed when using CSA and eCSA IEs together.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_ATTR_CSA_C_OFFSETS_TX which holds an array
of offsets to the CSA counters which should be updated
when sending a management frames with NL80211_CMD_FRAME.
This API should be used by the drivers that wish to keep the
CSA counter updated in probe responses, but do not implement
probe response offloading and so, do not use
ieee80211_proberesp_get function.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no need to pass NL80211_IFTYPE_UNSPECIFIED when calling
cfg80211_chandef_dfs_required() since we always already have the
interface type. So, pass the actual interface type instead.
Additionally, have cfg80211_chandef_dfs_required() WARN if the passed
interface type is NL80211_IFTYPE_UNSPECIFIED, so we can detect
problems more easily.
Tested-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At the moment, the ath9k/ath10k DFS module only supports detecting ETSI
radar patterns.
Add a bitmap in the interface combinations, indicating which DFS regions
are supported by the detector. If unset, support for all regions is
assumed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver fails during HW restart or resume, the whole
stack goes into a very confused state with interfaces being
up while the hardware is down etc.
Address this by shutting down everything; we'll run into a
lot of warnings in the process but that's better than having
the whole stack get messed up.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This exports a new cfg80211_stop_iface() function.
This is intended for driver internal interface
combination management and channel switching.
Due to locking issues (it re-enters driver) the
call is asynchronous and uses cfg80211 event
list/worker.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add locked-version for cfg80211_sched_scan_stopped.
This is used for some users that might want to
call it when rtnl is already locked.
Fixes: d43c6b6 ("mac80211: reschedule sched scan after HW restart")
Cc: stable@vger.kernel.org (3.14+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 is notified about connection failures by
__cfg80211_connect_result() call. However, this
function currently does not free cfg80211 sme.
This results in hanging connection attempts in some cases
e.g. when mac80211 authentication attempt is denied,
we have this function call:
ieee80211_rx_mgmt_auth() -> cfg80211_rx_mlme_mgmt() ->
cfg80211_process_auth() -> cfg80211_sme_rx_auth() ->
__cfg80211_connect_result()
but cfg80211_sme_free() is never get called.
Fixes: ceca7b712 ("cfg80211: separate internal SME implementation")
Cc: stable@vger.kernel.org (3.10+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These really can't trigger unless somebody messes up the code,
but don't make debugging it needlessly complicated, WARN and
return instead of BUG_ON().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends NL80211_CMD_SET_CHANNEL to allow dynamic channel bandwidth
changes in AP mode (including P2P GO) during a lifetime of the BSS. This
can be used to implement, e.g., HT 20/40 MHz co-existence rules on the
2.4 GHz band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current code checks if the 20MHz bandwidth is allowed for
particular channel -- if it is not, the channel is disabled.
Since we need to use 5/10 MHz channels, this code is modified in
the way that the default bandwidth to check is 5MHz. If the
maximum bandwidth allowed by the channel is smaller than 5MHz,
the channel is disabled. Otherwise the channel is used and the
flags are set according to the bandwidth allowed by the channel.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since there are frequency bands (e.g. 5.9GHz) allowing channels
with only 10 or 5 MHz bandwidth, this patch adds attributes that
allow keeping track about this information.
When channel attributes are reported to user-space, make sure to
not break old tools, i.e. if the 'split wiphy dump' is enabled,
report the extra attributes (if present) describing the bandwidth
restrictions. If the 'split wiphy dump' is not enabled,
completely omit those channels that have flags set to either
IEEE80211_CHAN_NO_10MHZ or IEEE80211_CHAN_NO_20MHZ.
Add the check for new bandwidth restriction flags in
cfg80211_chandef_usable() to comply with the restrictions.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Name wiphy_to_rdev is more accurate to describe what the function
does, i.e., return a pointer pointing to struct
cfg80211_registered_device.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Name "dev" is too common and ambiguous, let all the pointer name
pointing to struct cfg80211_registered_device be "rdev". This can
improve code readability and consistency(since other places have
already called it rdev).
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch splits cfg80211_check_combinations()
into an iterator function and a simple iteration
user.
This makes it possible for drivers to asses how
many channels can use given iftype setup. This in
turn can be used for future
multi-interface/multi-channel channel switching.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At some locations, channels 149-165 are considered a single
bundle, while at some other locations, e.g., Indonesia, channels
149-161 are considered a single bundle, while channel 165 belongs
to a different bundle. This means that:
1. A station interface connection to an AP on channel 165 allows
the instantiation of a P2P GO on channels 149-165.
2. A station interface connection to an AP on channels 149-161
does NOT allow the instantiation of a P2P GO on channel 165.
Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows processing of the last regulatory request when
we determine its still pending. Without this if a regulatory
request failed to get processed by userspace we wouldn't
be able to re-process it later. An example situation that can
lead to an unprocessed last_request is enabling cfg80211 to
be built-in to the kernel, not enabling CFG80211_INTERNAL_REGDB
and the CRDA binary not being available at the time the udev
rule that kicks of CRDA triggers.
In such a situation we want to let some cfg80211 triggers
eventually kick CRDA for us again. Without this if the first
cycle attempt to kick off CRDA failed we'd be stuck without
the ability to change process any further regulatory domains.
cfg80211 will trigger re-processing of the regulatory queue
whenever schedule_work(®_work) is called, currently this
happens when:
* suspend / resume
* disconnect
* a beacon hint gets triggered (non DFS 5 GHz AP found)
* a regulatory request gets added to the queue
We don't have any specific opportunistic late boot triggers
to address a late mount of where CRDA resides though, adding
that should be done separately through another patch.
Without an opportunistic fix then this fix relies at least
one of the triggeres above to happen.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid freeing the last request while it is being processed. This can
happen in some cases if reg_work is kicked for some reason while the
currently pending request is in flight.
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Eliad Peller <eliad@wizery.com>
Tested-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set DFS CAC time also in case of using custom
and strict regulatory from drivers. In other case
we could have unset DFS CAC time directly after
driver loaded and before issue regulatory set from
user mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When looking for a BSS matching given parameters, ignore invalid
BSSIDs. This avoids, for example, trying to join an IBSS that has
a multicast BSSID, which isn't supported by all drivers nor is it
a valid configuration of the IBSS so better create a new one with
a correctly chosen random BSSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_wext_freq() is declared in wext-compat.h, but its
parameter struct wiphy's declaration is not included there.
As the parameter isn't used, just remove it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
[remove parameter instead of changing to netdev]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All bits from radar_detect must match combination
radar bitmask. Otherwise it is theoretically
possible to lead into an invalid combination
provided a driver reports strange combinations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get rid of the cfg80211_can_add_interface() and
cfg80211_can_change_interface() functions by moving that functionality
to mac80211. With this patch all interface combination checks are now
out of cfg80211 (except for the channel switch case which will be
addressed in a future commit).
Additionally, modify the ieee80211_check_combinations() function so
that an undefined chandef can be passed, in order to use it before a
channel is defined.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that mac80211 can check the interface combinations itself, move
the combinations check from cfg80211 to mac80211 when joining an IBSS.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville