In preparation for naming the SHA-1 stuff in <linux/cryptohash.h>
properly and moving it to a more appropriate header, fix the HMAC-SHA256
code in mptcp_crypto_hmac_sha() to use SHA256_BLOCK_SIZE instead of
"SHA_MESSAGE_BYTES" which is actually the SHA-1 block size.
(Fortunately these are both 64 bytes, so this wasn't a "real" bug...)
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: mptcp@lists.01.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of manually allocating a 'struct shash_desc' on the stack and
calling crypto_shash_digest(), switch to using the new helper function
crypto_shash_tfm_digest() which does this for us.
Cc: linux-sctp@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of manually allocating a 'struct shash_desc' on the stack and
calling crypto_shash_digest(), switch to using the new helper function
crypto_shash_tfm_digest() which does this for us.
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
syzbot managed to trigger a recursive NETDEV_FEAT_CHANGE event
between bonding master and slave. I managed to find a reproducer
for this:
ip li set bond0 up
ifenslave bond0 eth0
brctl addbr br0
ethtool -K eth0 lro off
brctl addif br0 bond0
ip li set br0 up
When a NETDEV_FEAT_CHANGE event is triggered on a bonding slave,
it captures this and calls bond_compute_features() to fixup its
master's and other slaves' features. However, when syncing with
its lower devices by netdev_sync_lower_features() this event is
triggered again on slaves when the LRO feature fails to change,
so it goes back and forth recursively until the kernel stack is
exhausted.
Commit 17b85d29e8 intentionally lets __netdev_update_features()
return -1 for such a failure case, so we have to just rely on
the existing check inside netdev_sync_lower_features() and skip
NETDEV_FEAT_CHANGE event only for this specific failure case.
Fixes: fd867d51f8 ("net/core: generic support for disabling netdev features down stack")
Reported-by: syzbot+e73ceacfd8560cc8a3ca@syzkaller.appspotmail.com
Reported-by: syzbot+c2fb6f9ddcea95ba49b5@syzkaller.appspotmail.com
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jann Horn <jannh@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a subflow is created via mptcp_subflow_create_socket(),
a new 'struct socket' is allocated, with a new i_ino value.
When inspecting TCP sockets via the procfs and or the diag
interface, the above ones are not related to the process owning
the MPTCP master socket, even if they are a logical part of it
('ss -p' shows an empty process field)
Additionally, subflows created by the path manager get
the uid/gid from the running workqueue.
Subflows are part of the owning MPTCP master socket, let's
adjust the vfs info to reflect this.
After this patch, 'ss' correctly displays subflows as belonging
to the msk socket creator.
Fixes: 2303f994b3 ("mptcp: Associate MPTCP context with TCP socket")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 19bda36c4299ce3d7e5bce10bebe01764a655a6d:
| ipv6: add mtu lock check in __ip6_rt_update_pmtu
|
| Prior to this patch, ipv6 didn't do mtu lock check in ip6_update_pmtu.
| It leaded to that mtu lock doesn't really work when receiving the pkt
| of ICMPV6_PKT_TOOBIG.
|
| This patch is to add mtu lock check in __ip6_rt_update_pmtu just as ipv4
| did in __ip_rt_update_pmtu.
The above reasoning is incorrect. IPv6 *requires* icmp based pmtu to work.
There's already a comment to this effect elsewhere in the kernel:
$ git grep -p -B1 -A3 'RTAX_MTU lock'
net/ipv6/route.c=4813=
static int rt6_mtu_change_route(struct fib6_info *f6i, void *p_arg)
...
/* In IPv6 pmtu discovery is not optional,
so that RTAX_MTU lock cannot disable it.
We still use this lock to block changes
caused by addrconf/ndisc.
*/
This reverts to the pre-4.9 behaviour.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Fixes: 19bda36c42 ("ipv6: add mtu lock check in __ip6_rt_update_pmtu")
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix reference count leaks in various parts of batman-adv, from Xiyu
Yang.
2) Update NAT checksum even when it is zero, from Guillaume Nault.
3) sk_psock reference count leak in tls code, also from Xiyu Yang.
4) Sanity check TCA_FQ_CODEL_DROP_BATCH_SIZE netlink attribute in
fq_codel, from Eric Dumazet.
5) Fix panic in choke_reset(), also from Eric Dumazet.
6) Fix VLAN accel handling in bnxt_fix_features(), from Michael Chan.
7) Disallow out of range quantum values in sch_sfq, from Eric Dumazet.
8) Fix crash in x25_disconnect(), from Yue Haibing.
9) Don't pass pointer to local variable back to the caller in
nf_osf_hdr_ctx_init(), from Arnd Bergmann.
10) Wireguard should use the ECN decap helper functions, from Toke
Høiland-Jørgensen.
11) Fix command entry leak in mlx5 driver, from Moshe Shemesh.
12) Fix uninitialized variable access in mptcp's
subflow_syn_recv_sock(), from Paolo Abeni.
13) Fix unnecessary out-of-order ingress frame ordering in macsec, from
Scott Dial.
14) IPv6 needs to use a global serial number for dst validation just
like ipv4, from David Ahern.
15) Fix up PTP_1588_CLOCK deps, from Clay McClure.
16) Missing NLM_F_MULTI flag in gtp driver netlink messages, from
Yoshiyuki Kurauchi.
17) Fix a regression in that dsa user port errors should not be fatal,
from Florian Fainelli.
18) Fix iomap leak in enetc driver, from Dejin Zheng.
19) Fix use after free in lec_arp_clear_vccs(), from Cong Wang.
20) Initialize protocol value earlier in neigh code paths when
generating events, from Roman Mashak.
21) netdev_update_features() must be called with RTNL mutex in macsec
driver, from Antoine Tenart.
22) Validate untrusted GSO packets even more strictly, from Willem de
Bruijn.
23) Wireguard decrypt worker needs a cond_resched(), from Jason
Donenfeld.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
net: flow_offload: skip hw stats check for FLOW_ACTION_HW_STATS_DONT_CARE
MAINTAINERS: put DYNAMIC INTERRUPT MODERATION in proper order
wireguard: send/receive: use explicit unlikely branch instead of implicit coalescing
wireguard: selftests: initalize ipv6 members to NULL to squelch clang warning
wireguard: send/receive: cond_resched() when processing worker ringbuffers
wireguard: socket: remove errant restriction on looping to self
wireguard: selftests: use normal kernel stack size on ppc64
net: ethernet: ti: am65-cpsw-nuss: fix irqs type
ionic: Use debugfs_create_bool() to export bool
net: dsa: Do not leave DSA master with NULL netdev_ops
net: dsa: remove duplicate assignment in dsa_slave_add_cls_matchall_mirred
net: stricter validation of untrusted gso packets
seg6: fix SRH processing to comply with RFC8754
net: mscc: ocelot: ANA_AUTOAGE_AGE_PERIOD holds a value in seconds, not ms
net: dsa: ocelot: the MAC table on Felix is twice as large
net: dsa: sja1105: the PTP_CLK extts input reacts on both edges
selftests: net: tcp_mmap: fix SO_RCVLOWAT setting
net: hsr: fix incorrect type usage for protocol variable
net: macsec: fix rtnl locking issue
net: mvpp2: cls: Prevent buffer overflow in mvpp2_ethtool_cls_rule_del()
...
This patch adds FLOW_ACTION_HW_STATS_DONT_CARE which tells the driver
that the frontend does not need counters, this hw stats type request
never fails. The FLOW_ACTION_HW_STATS_DISABLED type explicitly requests
the driver to disable the stats, however, if the driver cannot disable
counters, it bails out.
TCA_ACT_HW_STATS_* maintains the 1:1 mapping with FLOW_ACTION_HW_STATS_*
except by disabled which is mapped to FLOW_ACTION_HW_STATS_DISABLED
(this is 0 in tc). Add tc_act_hw_stats() to perform the mapping between
TCA_ACT_HW_STATS_* and FLOW_ACTION_HW_STATS_*.
Fixes: 319a1d1947 ("flow_offload: check for basic action hw stats type")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ndo_get_phys_port_name() for the CPU port was added we introduced
an early check for when the DSA master network device in
dsa_master_ndo_setup() already implements ndo_get_phys_port_name(). When
we perform the teardown operation in dsa_master_ndo_teardown() we would
not be checking that cpu_dp->orig_ndo_ops was successfully allocated and
non-NULL initialized.
With network device drivers such as virtio_net, this leads to a NPD as
soon as the DSA switch hanging off of it gets torn down because we are
now assigning the virtio_net device's netdev_ops a NULL pointer.
Fixes: da7b9e9b00 ("net: dsa: Add ndo_get_phys_port_name() for CPU port")
Reported-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was caused by a poor merge conflict resolution on my side. The
"act = &cls->rule->action.entries[0];" assignment was already present in
the code prior to the patch mentioned below.
Fixes: e13c207528 ("net: dsa: refactor matchall mirred action to separate function")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Segment Routing Header (SRH) which defines the SRv6 dataplane is defined
in RFC8754.
RFC8754 (section 4.1) defines the SR source node behavior which encapsulates
packets into an outer IPv6 header and SRH. The SR source node encodes the
full list of Segments that defines the packet path in the SRH. Then, the
first segment from list of Segments is copied into the Destination address
of the outer IPv6 header and the packet is sent to the first hop in its path
towards the destination.
If the Segment list has only one segment, the SR source node can omit the SRH
as he only segment is added in the destination address.
RFC8754 (section 4.1.1) defines the Reduced SRH, when a source does not
require the entire SID list to be preserved in the SRH. A reduced SRH does
not contain the first segment of the related SR Policy (the first segment is
the one already in the DA of the IPv6 header), and the Last Entry field is
set to n-2, where n is the number of elements in the SR Policy.
RFC8754 (section 4.3.1.1) defines the SRH processing and the logic to
validate the SRH (S09, S10, S11) which works for both reduced and
non-reduced behaviors.
This patch updates seg6_validate_srh() to validate the SRH as per RFC8754.
Signed-off-by: Ahmed Abdelsalam <ahabdels@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse checker warning:-
net/hsr/hsr_slave.c:38:18: warning: incorrect type in assignment (different base types)
net/hsr/hsr_slave.c:38:18: expected unsigned short [unsigned] [usertype] protocol
net/hsr/hsr_slave.c:38:18: got restricted __be16 [usertype] h_proto
net/hsr/hsr_slave.c:39:25: warning: restricted __be16 degrades to integer
net/hsr/hsr_slave.c:39:57: warning: restricted __be16 degrades to integer
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bpf_tcp_ingress we used apply_bytes to subtract bytes from sg.size
which is used to track total bytes in a message. But this is not
correct because apply_bytes is itself modified in the main loop doing
the mem_charge.
Then at the end of this we have sg.size incorrectly set and out of
sync with actual sk values. Then we can get a splat if we try to
cork the data later and again try to redirect the msg to ingress. To
fix instead of trying to track msg.size do the easy thing and include
it as part of the sk_msg_xfer logic so that when the msg is moved the
sg.size is always correct.
To reproduce the below users will need ingress + cork and hit an
error path that will then try to 'free' the skmsg.
[ 173.699981] BUG: KASAN: null-ptr-deref in sk_msg_free_elem+0xdd/0x120
[ 173.699987] Read of size 8 at addr 0000000000000008 by task test_sockmap/5317
[ 173.700000] CPU: 2 PID: 5317 Comm: test_sockmap Tainted: G I 5.7.0-rc1+ #43
[ 173.700005] Hardware name: Dell Inc. Precision 5820 Tower/002KVM, BIOS 1.9.2 01/24/2019
[ 173.700009] Call Trace:
[ 173.700021] dump_stack+0x8e/0xcb
[ 173.700029] ? sk_msg_free_elem+0xdd/0x120
[ 173.700034] ? sk_msg_free_elem+0xdd/0x120
[ 173.700042] __kasan_report+0x102/0x15f
[ 173.700052] ? sk_msg_free_elem+0xdd/0x120
[ 173.700060] kasan_report+0x32/0x50
[ 173.700070] sk_msg_free_elem+0xdd/0x120
[ 173.700080] __sk_msg_free+0x87/0x150
[ 173.700094] tcp_bpf_send_verdict+0x179/0x4f0
[ 173.700109] tcp_bpf_sendpage+0x3ce/0x5d0
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/158861290407.14306.5327773422227552482.stgit@john-Precision-5820-Tower
When sk_msg_pop() is called where the pop operation is working on
the end of a sge element and there is no additional trailing data
and there _is_ data in front of pop, like the following case,
|____________a_____________|__pop__|
We have out of order operations where we incorrectly set the pop
variable so that instead of zero'ing pop we incorrectly leave it
untouched, effectively. This can cause later logic to shift the
buffers around believing it should pop extra space. The result is
we have 'popped' more data then we expected potentially breaking
program logic.
It took us a while to hit this case because typically we pop headers
which seem to rarely be at the end of a scatterlist elements but
we can't rely on this.
Fixes: 7246d8ed4d ("bpf: helper to pop data from messages")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/158861288359.14306.7654891716919968144.stgit@john-Precision-5820-Tower
When a new neighbor entry has been added, event is generated but it does not
include protocol, because its value is assigned after the event notification
routine has run, so move protocol assignment code earlier.
Fixes: df9b0e30d4 ("neighbor: Add protocol attribute")
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gengming reported a UAF in lec_arp_clear_vccs(),
where we add a vcc socket to an entry in a per-device
list but free the socket without removing it from the
list when vcc->dev is NULL.
We need to call lec_vcc_close() to search and remove
those entries contain the vcc being destroyed. This can
be done by calling vcc->push(vcc, NULL) unconditionally
in vcc_destroy_socket().
Another issue discovered by Gengming's reproducer is
the vcc->dev may point to the static device lecatm_dev,
for which we don't need to register/unregister device,
so we can just check for vcc->dev->ops->owner.
Reported-by: Gengming Liu <l.dmxcsnsbh@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we tell kernel to dump filters from root (ffff:ffff),
those filters on ingress (ffff:0000) are matched, but their
true parents must be dumped as they are. However, kernel
dumps just whatever we tell it, that is either ffff:ffff
or ffff:0000:
$ nl-cls-list --dev=dummy0 --parent=root
cls basic dev dummy0 id none parent root prio 49152 protocol ip match-all
cls basic dev dummy0 id :1 parent root prio 49152 protocol ip match-all
$ nl-cls-list --dev=dummy0 --parent=ffff:
cls basic dev dummy0 id none parent ffff: prio 49152 protocol ip match-all
cls basic dev dummy0 id :1 parent ffff: prio 49152 protocol ip match-all
This is confusing and misleading, more importantly this is
a regression since 4.15, so the old behavior must be restored.
And, when tc filters are installed on a tc class, the parent
should be the classid, rather than the qdisc handle. Commit
edf6711c98 ("net: sched: remove classid and q fields from tcf_proto")
removed the classid we save for filters, we can just restore
this classid in tcf_block.
Steps to reproduce this:
ip li set dev dummy0 up
tc qd add dev dummy0 ingress
tc filter add dev dummy0 parent ffff: protocol arp basic action pass
tc filter show dev dummy0 root
Before this patch:
filter protocol arp pref 49152 basic
filter protocol arp pref 49152 basic handle 0x1
action order 1: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
After this patch:
filter parent ffff: protocol arp pref 49152 basic
filter parent ffff: protocol arp pref 49152 basic handle 0x1
action order 1: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
Fixes: a10fa20101 ("net: sched: propagate q and parent from caller down to tcf_fill_node")
Fixes: edf6711c98 ("net: sched: remove classid and q fields from tcf_proto")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink health core conditions the reporter's recovery with the
expiration of the grace period. This is not relevant for the first
recovery. Explicitly demand that the grace period will only apply to
recoveries other than the first.
Fixes: c8e1da0bf9 ("devlink: Add health report functionality")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an application connects to the TIPC topology server and subscribes
to some services, a new connection is created along with some objects -
'tipc_subscription' to store related data correspondingly...
However, there is one omission in the connection handling that when the
connection or application is orderly shutdown (e.g. via SIGQUIT, etc.),
the connection is not closed in kernel, the 'tipc_subscription' objects
are not freed too.
This results in:
- The maximum number of subscriptions (65535) will be reached soon, new
subscriptions will be rejected;
- TIPC module cannot be removed (unless the objects are somehow forced
to release first);
The commit fixes the issue by closing the connection if the 'recvmsg()'
returns '0' i.e. when the peer is shutdown gracefully. It also includes
the other unexpected cases.
Acked-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to 1d27732f41 ("net: dsa: setup and teardown ports"), we would
not treat failures to set-up an user port as fatal, but after this
commit we would, which is a regression for some systems where interfaces
may be declared in the Device Tree, but the underlying hardware may not
be present (pluggable daughter cards for instance).
Fixes: 1d27732f41 ("net: dsa: setup and teardown ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not assume the attribute has the right size.
Fixes: aea5f654e6 ("net/sched: add skbprio scheduler")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include:
Stable fixes
- fix handling of backchannel binding in BIND_CONN_TO_SESSION
Bugfixes
- Fix a credential use-after-free issue in pnfs_roc()
- Fix potential posix_acl refcnt leak in nfs3_set_acl
- defer slow parts of rpc_free_client() to a workqueue
- Fix an Oopsable race in __nfs_list_for_each_server()
- Fix trace point use-after-free race
- Regression: the RDMA client no longer responds to server disconnect requests
- Fix return values of xdr_stream_encode_item_{present, absent}
- _pnfs_return_layout() must always wait for layoutreturn completion
Cleanups
- Remove unreachable error conditions
-----BEGIN PGP SIGNATURE-----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=w0zk
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- fix handling of backchannel binding in BIND_CONN_TO_SESSION
Bugfixes:
- Fix a credential use-after-free issue in pnfs_roc()
- Fix potential posix_acl refcnt leak in nfs3_set_acl
- defer slow parts of rpc_free_client() to a workqueue
- Fix an Oopsable race in __nfs_list_for_each_server()
- Fix trace point use-after-free race
- Regression: the RDMA client no longer responds to server disconnect
requests
- Fix return values of xdr_stream_encode_item_{present, absent}
- _pnfs_return_layout() must always wait for layoutreturn completion
Cleanups:
- Remove unreachable error conditions"
* tag 'nfs-for-5.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix a race in __nfs_list_for_each_server()
NFSv4.1: fix handling of backchannel binding in BIND_CONN_TO_SESSION
SUNRPC: defer slow parts of rpc_free_client() to a workqueue.
NFSv4: Remove unreachable error condition due to rpc_run_task()
SUNRPC: Remove unreachable error condition
xprtrdma: Fix use of xdr_stream_encode_item_{present, absent}
xprtrdma: Fix trace point use-after-free race
xprtrdma: Restore wake-up-all to rpcrdma_cm_event_handler()
nfs: Fix potential posix_acl refcnt leak in nfs3_set_acl
NFS/pnfs: Fix a credential use-after-free issue in pnfs_roc()
NFS/pnfs: Ensure that _pnfs_return_layout() waits for layoutreturn completion
The current gcc-10 snapshot produces a false-positive warning:
net/core/drop_monitor.c: In function 'trace_drop_common.constprop':
cc1: error: writing 8 bytes into a region of size 0 [-Werror=stringop-overflow=]
In file included from net/core/drop_monitor.c:23:
include/uapi/linux/net_dropmon.h:36:8: note: at offset 0 to object 'entries' with size 4 declared here
36 | __u32 entries;
| ^~~~~~~
I reported this in the gcc bugzilla, but in case it does not get
fixed in the release, work around it by using a temporary variable.
Fixes: 9a8afc8d39 ("Network Drop Monitor: Adding drop monitor implementation & Netlink protocol")
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=94881
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d5b90e99e1 ("devlink: report 0 after hitting end in region read")
fixed region dump, but region read still returns a spurious error:
$ devlink region read netdevsim/netdevsim1/dummy snapshot 0 addr 0 len 128
0000000000000000 a6 f4 c4 1c 21 35 95 a6 9d 34 c3 5b 87 5b 35 79
0000000000000010 f3 a0 d7 ee 4f 2f 82 7f c6 dd c4 f6 a5 c3 1b ae
0000000000000020 a4 fd c8 62 07 59 48 03 70 3b c7 09 86 88 7f 68
0000000000000030 6f 45 5d 6d 7d 0e 16 38 a9 d0 7a 4b 1e 1e 2e a6
0000000000000040 e6 1d ae 06 d6 18 00 85 ca 62 e8 7e 11 7e f6 0f
0000000000000050 79 7e f7 0f f3 94 68 bd e6 40 22 85 b6 be 6f b1
0000000000000060 af db ef 5e 34 f0 98 4b 62 9a e3 1b 8b 93 fc 17
devlink answers: Invalid argument
0000000000000070 61 e8 11 11 66 10 a5 f7 b1 ea 8d 40 60 53 ed 12
This is a minimal fix, I'll follow up with a restructuring
so we don't have two checks for the same condition.
Fixes: fdd41ec21e ("devlink: Return right error code in case of errors for region read")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nik reported a bug with pcpu dst cache when nexthop objects are
used illustrated by the following:
$ ip netns add foo
$ ip -netns foo li set lo up
$ ip -netns foo addr add 2001:db8:11::1/128 dev lo
$ ip netns exec foo sysctl net.ipv6.conf.all.forwarding=1
$ ip li add veth1 type veth peer name veth2
$ ip li set veth1 up
$ ip addr add 2001:db8:10::1/64 dev veth1
$ ip li set dev veth2 netns foo
$ ip -netns foo li set veth2 up
$ ip -netns foo addr add 2001:db8:10::2/64 dev veth2
$ ip -6 nexthop add id 100 via 2001:db8:10::2 dev veth1
$ ip -6 route add 2001:db8:11::1/128 nhid 100
Create a pcpu entry on cpu 0:
$ taskset -a -c 0 ip -6 route get 2001:db8:11::1
Re-add the route entry:
$ ip -6 ro del 2001:db8:11::1
$ ip -6 route add 2001:db8:11::1/128 nhid 100
Route get on cpu 0 returns the stale pcpu:
$ taskset -a -c 0 ip -6 route get 2001:db8:11::1
RTNETLINK answers: Network is unreachable
While cpu 1 works:
$ taskset -a -c 1 ip -6 route get 2001:db8:11::1
2001:db8:11::1 from :: via 2001:db8:10::2 dev veth1 src 2001:db8:10::1 metric 1024 pref medium
Conversion of FIB entries to work with external nexthop objects
missed an important difference between IPv4 and IPv6 - how dst
entries are invalidated when the FIB changes. IPv4 has a per-network
namespace generation id (rt_genid) that is bumped on changes to the FIB.
Checking if a dst_entry is still valid means comparing rt_genid in the
rtable to the current value of rt_genid for the namespace.
IPv6 also has a per network namespace counter, fib6_sernum, but the
count is saved per fib6_node. With the per-node counter only dst_entries
based on fib entries under the node are invalidated when changes are
made to the routes - limiting the scope of invalidations. IPv6 uses a
reference in the rt6_info, 'from', to track the corresponding fib entry
used to create the dst_entry. When validating a dst_entry, the 'from'
is used to backtrack to the fib6_node and check the sernum of it to the
cookie passed to the dst_check operation.
With the inline format (nexthop definition inline with the fib6_info),
dst_entries cached in the fib6_nh have a 1:1 correlation between fib
entries, nexthop data and dst_entries. With external nexthops, IPv6
looks more like IPv4 which means multiple fib entries across disparate
fib6_nodes can all reference the same fib6_nh. That means validation
of dst_entries based on external nexthops needs to use the IPv4 format
- the per-network namespace counter.
Add sernum to rt6_info and set it when creating a pcpu dst entry. Update
rt6_get_cookie to return sernum if it is set and update dst_check for
IPv6 to look for sernum set and based the check on it if so. Finally,
rt6_get_pcpu_route needs to validate the cached entry before returning
a pcpu entry (similar to the rt_cache_valid calls in __mkroute_input and
__mkroute_output for IPv4).
This problem only affects routes using the new, external nexthops.
Thanks to the kbuild test robot for catching the IS_ENABLED needed
around rt_genid_ipv6 before I sent this out.
Fixes: 5b98324ebe ("ipv6: Allow routes to use nexthop objects")
Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Do not update the UDP checksum when it's zero, from Guillaume Nault.
2) Fix return of local variable in nf_osf, from Arnd Bergmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
User space can request to delete a range of VLANs from a bridge slave in
one netlink request. For each deleted VLAN the FDB needs to be traversed
in order to flush all the affected entries.
If a large range of VLANs is deleted and the number of FDB entries is
large or the FDB lock is contented, it is possible for the kernel to
loop through the deleted VLANs for a long time. In case preemption is
disabled, this can result in a soft lockup.
Fix this by adding a schedule point after each VLAN is deleted to yield
the CPU, if needed. This is safe because the VLANs are traversed in
process context.
Fixes: bdced7ef78 ("bridge: support for multiple vlans and vlan ranges in setlink and dellink requests")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Tested-by: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_v{4,6}_syn_recv_sock() set 'own_req' only when returning
a not NULL 'child', let's check 'own_req' only if child is
available to avoid an - unharmful - UBSAN splat.
v1 -> v2:
- reference the correct hash
Fixes: 4c8941de78 ("mptcp: avoid flipping mp_capable field in syn_recv_sock()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing MPC+data packets we set the dss field, so
we must also initialize the data_fin, or we can find stray
value there.
Fixes: 9a19371bf0 ("mptcp: fix data_fin handing in RX path")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mentioned RX option field is initialized only for DSS
packet, we must access it only if 'dss' is set too, or
the subflow will end-up in a bad status, leading to
RFC violations.
Fixes: d22f4988ff ("mptcp: process MP_CAPABLE data option")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzcaller has found a way to trigger the WARN_ON_ONCE condition
in check_fully_established().
The root cause is a legit fallback to TCP scenario, so replace
the WARN with a plain message on a more strict condition.
Fixes: f296234c98 ("mptcp: Add handling of incoming MP_JOIN requests")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the MPTCP code uses 2 hooks to process syn-ack
packets, mptcp_rcv_synsent() and the sk_rx_dst_set()
callback.
We can drop the first, moving the relevant code into the
latter, reducing the hooking into the TCP code. This is
also needed by the next patch.
v1 -> v2:
- use local tcp sock ptr instead of casting the sk variable
several times - DaveM
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo points out that mptcp_disconnect is bogus:
"lock_sock(sk);
looks suspicious (lock should be already held by the caller)
And call to: tcp_disconnect(sk, flags); too, sk is not a tcp
socket".
->disconnect() gets called from e.g. inet_stream_connect when
one tries to disassociate a connected socket again (to re-connect
without closing the socket first).
MPTCP however uses mptcp_stream_connect, not inet_stream_connect,
for the mptcp-socket connect call.
inet_stream_connect only gets called indirectly, for the tcp socket,
so any ->disconnect() calls end up calling tcp_disconnect for that
tcp subflow sk.
This also explains why syzkaller has not yet reported a problem
here. So for now replace this with a stub that doesn't do anything.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/14
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-10 points out that a code path exists where a pointer to a stack
variable may be passed back to the caller:
net/netfilter/nfnetlink_osf.c: In function 'nf_osf_hdr_ctx_init':
cc1: warning: function may return address of local variable [-Wreturn-local-addr]
net/netfilter/nfnetlink_osf.c:171:16: note: declared here
171 | struct tcphdr _tcph;
| ^~~~~
I am not sure whether this can happen in practice, but moving the
variable declaration into the callers avoids the problem.
Fixes: 31a9c29210 ("netfilter: nf_osf: add struct nf_osf_hdr_ctx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Bugfixes:
- Restore wake-up-all to rpcrdma_cm_event_handler()
- Otherwise the client won't respond to server disconnect requests
- Fix tracepoint use-after-free race
- Fix usage of xdr_stream_encode_item_{present, absent}
- These functions return a size on success, and not 0
-----BEGIN PGP SIGNATURE-----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=jre3
-----END PGP SIGNATURE-----
Merge tag 'nfs-rdma-for-5.7-2' of git://git.linux-nfs.org/projects/anna/linux-nfs
NFSoRDMA Client Fixes for Linux 5.7
Bugfixes:
- Restore wake-up-all to rpcrdma_cm_event_handler()
- Otherwise the client won't respond to server disconnect requests
- Fix tracepoint use-after-free race
- Fix usage of xdr_stream_encode_item_{present, absent}
- These functions return a size on success, and not 0
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
The rpciod workqueue is on the write-out path for freeing dirty memory,
so it is important that it never block waiting for memory to be
allocated - this can lead to a deadlock.
rpc_execute() - which is often called by an rpciod work item - calls
rcp_task_release_client() which can lead to rpc_free_client().
rpc_free_client() makes two calls which could potentially block wating
for memory allocation.
rpc_clnt_debugfs_unregister() calls into debugfs and will block while
any of the debugfs files are being accessed. In particular it can block
while any of the 'open' methods are being called and all of these use
malloc for one thing or another. So this can deadlock if the memory
allocation waits for NFS to complete some writes via rpciod.
rpc_clnt_remove_pipedir() can take the inode_lock() and while it isn't
obvious that memory allocations can happen while the lock it held, it is
safer to assume they might and to not let rpciod call
rpc_clnt_remove_pipedir().
So this patch moves these two calls (together with the final kfree() and
rpciod_down()) into a work-item to be run from the system work-queue.
rpciod can continue its important work, and the final stages of the free
can happen whenever they happen.
I have seen this deadlock on a 4.12 based kernel where debugfs used
synchronize_srcu() when removing objects. synchronize_srcu() requires a
workqueue and there were no free workther threads and none could be
allocated. While debugsfs no longer uses SRCU, I believe the deadlock
is still possible.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
tcp_bpf_recvmsg() invokes sk_psock_get(), which returns a reference of
the specified sk_psock object to "psock" with increased refcnt.
When tcp_bpf_recvmsg() returns, local variable "psock" becomes invalid,
so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in several exception handling paths
of tcp_bpf_recvmsg(). When those error scenarios occur such as "flags"
includes MSG_ERRQUEUE, the function forgets to decrease the refcnt
increased by sk_psock_get(), causing a refcnt leak.
Fix this issue by calling sk_psock_put() or pulling up the error queue
read handling when those error scenarios occur.
Fixes: e7a5f1f1cd ("bpf/sockmap: Read psock ingress_msg before sk_receive_queue")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/1587872115-42805-1-git-send-email-xiyuyang19@fudan.edu.cn
- fix random number generation in network coding, by George Spelvin
- fix reference counter leaks, by Xiyu Yang (3 patches)
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEE1ilQI7G+y+fdhnrfoSvjmEKSnqEFAl6m8zEWHHN3QHNpbW9u
d3VuZGVybGljaC5kZQAKCRChK+OYQpKeoc4dD/9rKLN853rKJe30QkOBJeinSJOO
/aEgCbsOVxgLCfvZxdiwSDQRTPFxChXcNZri6cuHu4h7T9ZYcBEKQNRy4D//h9YH
9wx2+WP7rTKtfScVqOnBf+03fIYzOS9qQnpoA/6id3YIqg5AAhCTB2n5CS1/ILI4
6WrDfsJH4jgol4Ud+lVAFSokjElxVpQ+5AlcKVTBGli1f4aReu7g3xPSZVIBuikz
axsO3UEfzLNU+k+Y3Y+/97HWdaEFelIkLoymZSSOxJ/BRX2Dz8M/eUyy/p5iVzb2
gSF46estgvJodVYrwUEb3UtSSpHP0p562h2QxxjqgayObpJQDwKNeEWkmwHb5RcF
a8l025LlA9+iW25r/RttXiQ0FoLymY1PCdcsY36MZUXAnFn0UyRv/Zt1CUosoImc
C9+CA7jM9XlXeipXnHQvNryUcqwsJJI1hUF7WmIRuOAdeqcvNPTzLiCYWAGQmZ4U
V9CdHQseFKgNnDTaoraW5AMJmuP8frXKcdJd4XWJvOgQO6rX53VTEYqmzqBjFjQZ
dynAIY1w+REmbqYeROgpp02VVXpXw7LVgKRyQIaDJa0cjXfpgmWATyWuewgLgfyK
9EGp2Adu4z7QoVRG7I9Uq2UwPuDVPbbKohNgQZsJt98itKkqv1afQ8U83ref6LQO
5/Mbxke3iQ9ftYVqlg==
=fNPb
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20200427' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- fix random number generation in network coding, by George Spelvin
- fix reference counter leaks, by Xiyu Yang (3 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot managed to set up sfq so that q->scaled_quantum was zero,
triggering an infinite loop in sfq_dequeue()
More generally, we must only accept quantum between 1 and 2^18 - 7,
meaning scaled_quantum must be in [1, 0x7FFF] range.
Otherwise, we also could have a loop in sfq_dequeue()
if scaled_quantum happens to be 0x8000, since slot->allot
could indefinitely switch between 0 and 0x8000.
Fixes: eeaeb068f1 ("sch_sfq: allow big packets and be fair")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+0251e883fe39e7a0cb0a@syzkaller.appspotmail.com
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My intent was to not let users set a zero drop_batch_size,
it seems I once again messed with min()/max().
Fixes: 9d18562a22 ("fq_codel: add batch ability to fq_codel_drop()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tls_data_ready() invokes sk_psock_get(), which returns a reference of
the specified sk_psock object to "psock" with increased refcnt.
When tls_data_ready() returns, local variable "psock" becomes invalid,
so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
tls_data_ready(). When "psock->ingress_msg" is empty but "psock" is not
NULL, the function forgets to decrease the refcnt increased by
sk_psock_get(), causing a refcnt leak.
Fix this issue by calling sk_psock_put() on all paths when "psock" is
not NULL.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
x25_connect() invokes x25_get_neigh(), which returns a reference of the
specified x25_neigh object to "x25->neighbour" with increased refcnt.
When x25 connect success and returns, the reference still be hold by
"x25->neighbour", so the refcount should be decreased in
x25_disconnect() to keep refcount balanced.
The reference counting issue happens in x25_disconnect(), which forgets
to decrease the refcnt increased by x25_get_neigh() in x25_connect(),
causing a refcnt leak.
Fix this issue by calling x25_neigh_put() before x25_disconnect()
returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_exec_tx_verdict() invokes sk_psock_get(), which returns a reference
of the specified sk_psock object to "psock" with increased refcnt.
When bpf_exec_tx_verdict() returns, local variable "psock" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
bpf_exec_tx_verdict(). When "policy" equals to NULL but "psock" is not
NULL, the function forgets to decrease the refcnt increased by
sk_psock_get(), causing a refcnt leak.
Fix this issue by calling sk_psock_put() on this error path before
bpf_exec_tx_verdict() returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In virtio_transport.c, if the virtqueue is full, the transmitting
packet is queued up and it will be sent in the next iteration.
This causes the same packet to be delivered multiple times to
monitoring devices.
We want to continue to deliver packets to monitoring devices before
it is put in the virtqueue, to avoid that replies can appear in the
packet capture before the transmitted packet.
This patch fixes the issue, adding a new flag (tap_delivered) in
struct virtio_vsock_pkt, to check if the packet is already delivered
to monitoring devices.
In vhost/vsock.c, we are splitting packets, so we must set
'tap_delivered' to false when we queue up the same virtio_vsock_pkt
to handle the remaining bytes.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've noticed that when krb5i or krb5p security is in use,
retransmitted requests are missing the server's duplicate reply
cache. The computed checksum on the retransmitted request does not
match the cached checksum, resulting in the server performing the
retransmitted request again instead of returning the cached reply.
The assumptions made when removing xdr_buf_trim() were not correct.
In the send paths, the upper layer has already set the segment
lengths correctly, and shorting the buffer's content is simply a
matter of reducing buf->len.
xdr_buf_trim() is the right answer in the receive/unwrap path on
both the client and the server. The buffer segment lengths have to
be shortened one-by-one.
On the server side in particular, head.iov_len needs to be updated
correctly to enable nfsd_cache_csum() to work correctly. The simple
buf->len computation doesn't do that, and that results in
checksumming stale data in the buffer.
The problem isn't noticed until there's significant instability of
the RPC transport. At that point, the reliability of retransmit
detection on the server becomes crucial.
Fixes: 241b1f419f ("SUNRPC: Remove xdr_buf_trim()")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
When the au_ralign field was added to gss_unwrap_resp_priv, the
wrong calculation was used. Setting au_rslack == au_ralign is
probably correct for kerberos_v1 privacy, but kerberos_v2 privacy
adds additional GSS data after the clear text RPC message.
au_ralign needs to be smaller than au_rslack in that fairly common
case.
When xdr_buf_trim() is restored to gss_unwrap_kerberos_v2(), it does
exactly what I feared it would: it trims off part of the clear text
RPC message. However, that's because rpc_prepare_reply_pages() does
not set up the rq_rcv_buf's tail correctly because au_ralign is too
large.
Fixing the au_ralign computation also corrects the alignment of
rq_rcv_buf->pages so that the client does not have to shift reply
data payloads after they are received.
Fixes: 35e77d21ba ("SUNRPC: Add rpc_auth::au_ralign field")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Refactor: This is a pre-requisite to fixing the client-side ralign
computation in gss_unwrap_resp_priv().
The length value is passed in explicitly rather that as the value
of buf->len. This will subsequently allow gss_unwrap_kerberos_v1()
to compute a slack and align value, instead of computing it in
gss_unwrap_resp_priv().
Fixes: 35e77d21ba ("SUNRPC: Add rpc_auth::au_ralign field")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
If the UDP header of a local VXLAN endpoint is NAT-ed, and the VXLAN
device has disabled UDP checksums and enabled Tx checksum offloading,
then the skb passed to udp_manip_pkt() has hdr->check == 0 (outer
checksum disabled) and skb->ip_summed == CHECKSUM_PARTIAL (inner packet
checksum offloaded).
Because of the ->ip_summed value, udp_manip_pkt() tries to update the
outer checksum with the new address and port, leading to an invalid
checksum sent on the wire, as the original null checksum obviously
didn't take the old address and port into account.
So, we can't take ->ip_summed into account in udp_manip_pkt(), as it
might not refer to the checksum we're acting on. Instead, we can base
the decision to update the UDP checksum entirely on the value of
hdr->check, because it's null if and only if checksum is disabled:
* A fully computed checksum can't be 0, since a 0 checksum is
represented by the CSUM_MANGLED_0 value instead.
* A partial checksum can't be 0, since the pseudo-header always adds
at least one non-zero value (the UDP protocol type 0x11) and adding
more values to the sum can't make it wrap to 0 as the carry is then
added to the wrapped number.
* A disabled checksum uses the special value 0.
The problem seems to be there from day one, although it was probably
not visible before UDP tunnels were implemented.
Fixes: 5b1158e909 ("[NETFILTER]: Add NAT support for nf_conntrack")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit b656722906 ("net: Increase the size of skb_frag_t")
removed the 16bit limitation of a frag on some 32bit arches.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently subflow_finish_connect() changes unconditionally
any msk socket status other than TCP_ESTABLISHED.
If an unblocking connect() races with close(), we can end-up
triggering:
IPv4: Attempt to release TCP socket in state 1 00000000e32b8b7e
when the msk socket is disposed.
Be sure to enter the established status only from SYN_SENT.
Fixes: c3c123d16c ("net: mptcp: don't hang in mptcp_sendmsg() after TCP fallback")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix memory leak in netfilter flowtable, from Roi Dayan.
2) Ref-count leaks in netrom and tipc, from Xiyu Yang.
3) Fix warning when mptcp socket is never accepted before close, from
Florian Westphal.
4) Missed locking in ovs_ct_exit(), from Tonghao Zhang.
5) Fix large delays during PTP synchornization in cxgb4, from Rahul
Lakkireddy.
6) team_mode_get() can hang, from Taehee Yoo.
7) Need to use kvzalloc() when allocating fw tracer in mlx5 driver,
from Niklas Schnelle.
8) Fix handling of bpf XADD on BTF memory, from Jann Horn.
9) Fix BPF_STX/BPF_B encoding in x86 bpf jit, from Luke Nelson.
10) Missing queue memory release in iwlwifi pcie code, from Johannes
Berg.
11) Fix NULL deref in macvlan device event, from Taehee Yoo.
12) Initialize lan87xx phy correctly, from Yuiko Oshino.
13) Fix looping between VRF and XFRM lookups, from David Ahern.
14) etf packet scheduler assumes all sockets are full sockets, which is
not necessarily true. From Eric Dumazet.
15) Fix mptcp data_fin handling in RX path, from Paolo Abeni.
16) fib_select_default() needs to handle nexthop objects, from David
Ahern.
17) Use GFP_ATOMIC under spinlock in mac80211_hwsim, from Wei Yongjun.
18) vxlan and geneve use wrong nlattr array, from Sabrina Dubroca.
19) Correct rx/tx stats in bcmgenet driver, from Doug Berger.
20) BPF_LDX zero-extension is encoded improperly in x86_32 bpf jit, fix
from Luke Nelson.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (100 commits)
selftests/bpf: Fix a couple of broken test_btf cases
tools/runqslower: Ensure own vmlinux.h is picked up first
bpf: Make bpf_link_fops static
bpftool: Respect the -d option in struct_ops cmd
selftests/bpf: Add test for freplace program with expected_attach_type
bpf: Propagate expected_attach_type when verifying freplace programs
bpf: Fix leak in LINK_UPDATE and enforce empty old_prog_fd
bpf, x86_32: Fix logic error in BPF_LDX zero-extension
bpf, x86_32: Fix clobbering of dst for BPF_JSET
bpf, x86_32: Fix incorrect encoding in BPF_LDX zero-extension
bpf: Fix reStructuredText markup
net: systemport: suppress warnings on failed Rx SKB allocations
net: bcmgenet: suppress warnings on failed Rx SKB allocations
macsec: avoid to set wrong mtu
mac80211: sta_info: Add lockdep condition for RCU list usage
mac80211: populate debugfs only after cfg80211 init
net: bcmgenet: correct per TX/RX ring statistics
net: meth: remove spurious copyright text
net: phy: bcm84881: clear settings on link down
chcr: Fix CPU hard lockup
...
* fix a wrong GFP_KERNEL in hwsim
* fix the debugfs mess after the mac80211 registration race fix
* suppress false-positive RCU list lockdep warnings
-----BEGIN PGP SIGNATURE-----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=SKNj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2020-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just three changes:
* fix a wrong GFP_KERNEL in hwsim
* fix the debugfs mess after the mac80211 registration race fix
* suppress false-positive RCU list lockdep warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sta_info_get_by_idx() uses RCU list primitive.
It is called with local->sta_mtx held from mac80211/cfg.c.
Add lockdep expression to avoid any false positive RCU list warnings.
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200409082906.27427-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When fixing the initialization race, we neglected to account for
the fact that debugfs is initialized in wiphy_register(), and
some debugfs things went missing (or rather were rerooted to the
global debugfs root).
Fix this by adding debugfs entries only after wiphy_register().
This requires some changes in the rate control code since it
currently adds debugfs at alloc time, which can no longer be
done after the reordering.
Reported-by: Jouni Malinen <j@w1.fi>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Felix Fietkau <nbd@nbd.name>
Cc: stable@vger.kernel.org
Fixes: 52e04b4ce5 ("mac80211: fix race in ieee80211_register_hw()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200423111344.0e00d3346f12.Iadc76a03a55093d94391fc672e996a458702875d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
x25_lapb_receive_frame() invokes x25_get_neigh(), which returns a
reference of the specified x25_neigh object to "nb" with increased
refcnt.
When x25_lapb_receive_frame() returns, local variable "nb" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one path of
x25_lapb_receive_frame(). When pskb_may_pull() returns false, the
function forgets to decrease the refcnt increased by x25_get_neigh(),
causing a refcnt leak.
Fix this issue by calling x25_neigh_put() when pskb_may_pull() returns
false.
Fixes: cb101ed2c3 ("x25: Handle undersized/fragmented skbs")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normal there should be checked for nla_put_in6_addr like other
usage in net.
Detected by CoverityScan, CID# 1461639
Fixes: 01cacb00b3 ("mptcp: add netlink-based PM")
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Address several use-after-free and memory leak bugs
- Prevent a backchannel livelock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Zoup
-----END PGP SIGNATURE-----
Merge tag 'nfsd-5.7-rc-1' of git://git.linux-nfs.org/projects/cel/cel-2.6
Pull nfsd fixes from Chuck Lever:
"The first set of 5.7-rc fixes for NFS server issues.
These were all unresolved at the time the 5.7 window opened, and
needed some additional time to ensure they were correctly addressed.
They are ready now.
At the moment I know of one more urgent issue regarding the NFS
server. A fix has been tested and is under review. I expect to send
one more pull request, containing this fix (which now consists of 3
patches).
Fixes:
- Address several use-after-free and memory leak bugs
- Prevent a backchannel livelock"
* tag 'nfsd-5.7-rc-1' of git://git.linux-nfs.org/projects/cel/cel-2.6:
svcrdma: Fix leak of svc_rdma_recv_ctxt objects
svcrdma: Fix trace point use-after-free race
SUNRPC: Fix backchannel RPC soft lockups
SUNRPC/cache: Fix unsafe traverse caused double-free in cache_purge
nfsd: memory corruption in nfsd4_lock()
In Commit dd9ee34440 ("vti4: Fix a ipip packet processing bug in
'IPCOMP' virtual tunnel"), it tries to receive IPIP packets in vti
by calling xfrm_input(). This case happens when a small packet or
frag sent by peer is too small to get compressed.
However, xfrm_input() will still get to the IPCOMP path where skb
sec_path is set, but never dropped while it should have been done
in vti_ipcomp4_protocol.cb_handler(vti_rcv_cb), as it's not an
ipcomp4 packet. This will cause that the packet can never pass
xfrm4_policy_check() in the upper protocol rcv functions.
So this patch is to call ip_tunnel_rcv() to process IPIP packets
instead.
Fixes: dd9ee34440 ("vti4: Fix a ipip packet processing bug in 'IPCOMP' virtual tunnel")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The NetLabel Tools project has moved from http://netlabel.sf.net to a
GitHub project. Update to directly refer to the new home for the tools.
Signed-off-by: Salvatore Bonaccorso <carnil@debian.org>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data fin flag is set only via a DSS option, but
mptcp_incoming_options() copies it unconditionally from the
provided RX options.
Since we do not clear all the mptcp sock RX options in a
socket free/alloc cycle, we can end-up with a stray data_fin
value while parsing e.g. MPC packets.
That would lead to mapping data corruption and will trigger
a few WARN_ON() in the RX path.
Instead of adding a costly memset(), fetch the data_fin flag
only for DSS packets - when we always explicitly initialize
such bit at option parsing time.
Fixes: 648ef4b886 ("mptcp: Implement MPTCP receive path")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When starting shutdown in sctp_sf_do_dupcook_a(), get the value for
SHUTDOWN Cumulative TSN Ack from the new association, which is
reconstructed from the cookie, instead of the old association, which
the peer doesn't have anymore.
Otherwise the SHUTDOWN is either ignored or replied to with an ABORT
by the peer because CTSN Ack doesn't match the peer's Initial TSN.
Fixes: bdf6fa52f0 ("sctp: handle association restarts when the socket is closed.")
Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we start shutdown in sctp_sf_do_dupcook_a(), we want to bundle
the SHUTDOWN with the COOKIE-ACK to ensure that the peer receives them
at the same time and in the correct order. This bundling was broken by
commit 4ff40b8626 ("sctp: set chunk transport correctly when it's a
new asoc"), which assigns a transport for the COOKIE-ACK, but not for
the SHUTDOWN.
Fix this by passing a reference to the COOKIE-ACK chunk as an argument
to sctp_sf_do_9_2_start_shutdown() and onward to
sctp_make_shutdown(). This way the SHUTDOWN chunk is assigned the same
transport as the COOKIE-ACK chunk, which allows them to be bundled.
In sctp_sf_do_9_2_start_shutdown(), the void *arg parameter was
previously unused. Now that we're taking it into use, it must be a
valid pointer to a chunk, or NULL. There is only one call site where
it's not, in sctp_sf_autoclose_timer_expire(). Fix that too.
Fixes: 4ff40b8626 ("sctp: set chunk transport correctly when it's a new asoc")
Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to fail the probing of the switch if the MTU couldn't
be configured correctly (either the switch port itself, or the host
port) for whatever reason. MTU-sized traffic probably won't work, sure,
but we can still probably limp on and support some form of communication
anyway, which the users would probably appreciate more.
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPSKB_XFRM_TRANSFORMED and IP6SKB_XFRM_TRANSFORMED are skb flags set by
xfrm code to tell other skb handlers that the packet has been passed
through the xfrm output functions. Simplify the code and just always
set them rather than conditionally based on netfilter enabled thus
making the flag available for other users.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rpc_clnt_test_and_add_xprt() invokes rpc_call_null_helper(), which
return the value of rpc_run_task() to "task". Since rpc_run_task() is
impossible to return an ERR pointer, there is no need to add the
IS_ERR() condition on "task" here. So we need to remove it.
Fixes: 7f55489058 ("SUNRPC: Allow addition of new transports to a struct rpc_clnt")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Commit 018d26fcd1 ("cgroup, netclassid: periodically release file_lock
on classid") added a second cond_resched to write_classid indirectly by
update_classid_task. Remove the one in write_classid.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Dmitry Yakunin <zeil@yandex-team.ru>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) flow_block_cb memleak in nf_flow_table_offload_del_cb(), from Roi Dayan.
2) Fix error path handling in nf_nat_inet_register_fn(), from Hillf Danton.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
batadv_v_ogm_process() invokes batadv_hardif_neigh_get(), which returns
a reference of the neighbor object to "hardif_neigh" with increased
refcount.
When batadv_v_ogm_process() returns, "hardif_neigh" becomes invalid, so
the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling paths of
batadv_v_ogm_process(). When batadv_v_ogm_orig_get() fails to get the
orig node and returns NULL, the refcnt increased by
batadv_hardif_neigh_get() is not decreased, causing a refcnt leak.
Fix this issue by jumping to "out" label when batadv_v_ogm_orig_get()
fails to get the orig node.
Fixes: 9323158ef9 ("batman-adv: OGMv2 - implement originators logic")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batadv_show_throughput_override() invokes batadv_hardif_get_by_netdev(),
which gets a batadv_hard_iface object from net_dev with increased refcnt
and its reference is assigned to a local pointer 'hard_iface'.
When batadv_store_throughput_override() returns, "hard_iface" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The issue happens in one error path of
batadv_store_throughput_override(). When batadv_parse_throughput()
returns NULL, the refcnt increased by batadv_hardif_get_by_netdev() is
not decreased, causing a refcnt leak.
Fix this issue by jumping to "out" label when batadv_parse_throughput()
returns NULL.
Fixes: 0b5ecc6811 ("batman-adv: add throughput override attribute to hard_ifaces")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batadv_show_throughput_override() invokes batadv_hardif_get_by_netdev(),
which gets a batadv_hard_iface object from net_dev with increased refcnt
and its reference is assigned to a local pointer 'hard_iface'.
When batadv_show_throughput_override() returns, "hard_iface" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The issue happens in the normal path of
batadv_show_throughput_override(), which forgets to decrease the refcnt
increased by batadv_hardif_get_by_netdev() before the function returns,
causing a refcnt leak.
Fix this issue by calling batadv_hardif_put() before the
batadv_show_throughput_override() returns in the normal path.
Fixes: 0b5ecc6811 ("batman-adv: add throughput override attribute to hard_ifaces")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
and change to pseudorandom numbers, as this is a traffic dithering
operation that doesn't need crypto-grade.
The previous code operated in 4 steps:
1. Generate a random byte 0 <= rand_tq <= 255
2. Multiply it by BATADV_TQ_MAX_VALUE - tq
3. Divide by 255 (= BATADV_TQ_MAX_VALUE)
4. Return BATADV_TQ_MAX_VALUE - rand_tq
This would apperar to scale (BATADV_TQ_MAX_VALUE - tq) by a random
value between 0/255 and 255/255.
But! The intermediate value between steps 3 and 4 is stored in a u8
variable. So it's truncated, and most of the time, is less than 255, after
which the division produces 0. Specifically, if tq is odd, the product is
always even, and can never be 255. If tq is even, there's exactly one
random byte value that will produce a product byte of 255.
Thus, the return value is 255 (511/512 of the time) or 254 (1/512
of the time).
If we assume that the truncation is a bug, and the code is meant to scale
the input, a simpler way of looking at it is that it's returning a random
value between tq and BATADV_TQ_MAX_VALUE, inclusive.
Well, we have an optimized function for doing just that.
Fixes: 3c12de9a5c ("batman-adv: network coding - code and transmit packets if possible")
Signed-off-by: George Spelvin <lkml@sdf.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
An use-after-free crash can be triggered when sending big packets over
vxlan over esp with esp offload enabled:
[] BUG: KASAN: use-after-free in ipv6_gso_pull_exthdrs.part.8+0x32c/0x4e0
[] Call Trace:
[] dump_stack+0x75/0xa0
[] kasan_report+0x37/0x50
[] ipv6_gso_pull_exthdrs.part.8+0x32c/0x4e0
[] ipv6_gso_segment+0x2c8/0x13c0
[] skb_mac_gso_segment+0x1cb/0x420
[] skb_udp_tunnel_segment+0x6b5/0x1c90
[] inet_gso_segment+0x440/0x1380
[] skb_mac_gso_segment+0x1cb/0x420
[] esp4_gso_segment+0xae8/0x1709 [esp4_offload]
[] inet_gso_segment+0x440/0x1380
[] skb_mac_gso_segment+0x1cb/0x420
[] __skb_gso_segment+0x2d7/0x5f0
[] validate_xmit_skb+0x527/0xb10
[] __dev_queue_xmit+0x10f8/0x2320 <---
[] ip_finish_output2+0xa2e/0x1b50
[] ip_output+0x1a8/0x2f0
[] xfrm_output_resume+0x110e/0x15f0
[] __xfrm4_output+0xe1/0x1b0
[] xfrm4_output+0xa0/0x200
[] iptunnel_xmit+0x5a7/0x920
[] vxlan_xmit_one+0x1658/0x37a0 [vxlan]
[] vxlan_xmit+0x5e4/0x3ec8 [vxlan]
[] dev_hard_start_xmit+0x125/0x540
[] __dev_queue_xmit+0x17bd/0x2320 <---
[] ip6_finish_output2+0xb20/0x1b80
[] ip6_output+0x1b3/0x390
[] ip6_xmit+0xb82/0x17e0
[] inet6_csk_xmit+0x225/0x3d0
[] __tcp_transmit_skb+0x1763/0x3520
[] tcp_write_xmit+0xd64/0x5fe0
[] __tcp_push_pending_frames+0x8c/0x320
[] tcp_sendmsg_locked+0x2245/0x3500
[] tcp_sendmsg+0x27/0x40
As on the tx path of vxlan over esp, skb->inner_network_header would be
set on vxlan_xmit() and xfrm4_tunnel_encap_add(), and the later one can
overwrite the former one. It causes skb_udp_tunnel_segment() to use a
wrong skb->inner_network_header, then the issue occurs.
This patch is to fix it by calling xfrm_output_gso() instead when the
inner_protocol is set, in which gso_segment of inner_protocol will be
done first.
While at it, also improve some code around.
Fixes: 7862b4058b ("esp: Add gso handlers for esp4 and esp6")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
For beet mode, when it's ipv6 inner address with nexthdrs set,
the packet format might be:
----------------------------------------------------
| outer | | dest | | | ESP | ESP |
| IP hdr | ESP | opts.| TCP | Data | Trailer | ICV |
----------------------------------------------------
Before doing gso segment in xfrm4_beet_gso_segment(), the same
thing is needed as it does in xfrm6_beet_gso_segment() in last
patch 'esp6: support ipv6 nexthdrs process for beet gso segment'.
v1->v2:
- remove skb_transport_offset(), as it will always return 0
in xfrm6_beet_gso_segment(), thank Sabrina's check.
Fixes: 384a46ea7b ("esp4: add gso_segment for esp4 beet mode")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
For beet mode, when it's ipv6 inner address with nexthdrs set,
the packet format might be:
----------------------------------------------------
| outer | | dest | | | ESP | ESP |
| IP6 hdr| ESP | opts.| TCP | Data | Trailer | ICV |
----------------------------------------------------
Before doing gso segment in xfrm6_beet_gso_segment(), it should
skip all nexthdrs and get the real transport proto, and set
transport_header properly.
This patch is to fix it by simply calling ipv6_skip_exthdr()
in xfrm6_beet_gso_segment().
v1->v2:
- remove skb_transport_offset(), as it will always return 0
in xfrm6_beet_gso_segment(), thank Sabrina's check.
Fixes: 7f9e40eb18 ("esp6: add gso_segment for esp6 beet mode")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We don't need them, as we can use the current ingress opt
data instead. Setting them in syn_recv_sock() may causes
inconsistent mptcp socket status, as per previous commit.
Fixes: cc7972ea19 ("mptcp: parse and emit MP_CAPABLE option according to v1 spec")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If multiple CPUs races on the same req_sock in syn_recv_sock(),
flipping such field can cause inconsistent child socket status.
When racing, the CPU losing the req ownership may still change
the mptcp request socket mp_capable flag while the CPU owning
the request is cloning the socket, leaving the child socket with
'is_mptcp' set but no 'mp_capable' flag.
Such socket will stay with 'conn' field cleared, heading to oops
in later mptcp callback.
Address the issue tracking the fallback status in a local variable.
Fixes: 58b0991962 ("mptcp: create msk early")
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following splat can occur during self test:
BUG: KASAN: use-after-free in subflow_data_ready+0x156/0x160
Read of size 8 at addr ffff888100c35c28 by task mptcp_connect/4808
subflow_data_ready+0x156/0x160
tcp_child_process+0x6a3/0xb30
tcp_v4_rcv+0x2231/0x3730
ip_protocol_deliver_rcu+0x5c/0x860
ip_local_deliver_finish+0x220/0x360
ip_local_deliver+0x1c8/0x4e0
ip_rcv_finish+0x1da/0x2f0
ip_rcv+0xd0/0x3c0
__netif_receive_skb_one_core+0xf5/0x160
__netif_receive_skb+0x27/0x1c0
process_backlog+0x21e/0x780
net_rx_action+0x35f/0xe90
do_softirq+0x4c/0x50
[..]
This occurs when accessing subflow_ctx->conn.
Problem is that tcp_child_process() calls listen sockets'
sk_data_ready() notification, but it doesn't hold the listener
lock. Another cpu calling close() on the listener will then cause
transition of refcount to 0.
Fixes: 58b0991962 ("mptcp: create msk early")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b6f6118901 ("ipv6: restrict IPV6_ADDRFORM operation") fixed a
problem found by syzbot an unfortunate logic error meant that it
also broke IPV6_ADDRFORM.
Rearrange the checks so that the earlier test is just one of the series
of checks made before moving the socket from IPv6 to IPv4.
Fixes: b6f6118901 ("ipv6: restrict IPV6_ADDRFORM operation")
Signed-off-by: John Haxby <john.haxby@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
These new helpers do not return 0 on success, they return the
encoded size. Thus they are not a drop-in replacement for the
old helpers.
Fixes: 5c266df527 ("SUNRPC: Add encoders for list item discriminators")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
It's not safe to use resources pointed to by the @send_wr of
ib_post_send() _after_ that function returns. Those resources are
typically freed by the Send completion handler, which can run before
ib_post_send() returns.
Thus the trace points currently around ib_post_send() in the
client's RPC/RDMA transport are a hazard, even when they are
disabled. Rearrange them so that they touch the Work Request only
_before_ ib_post_send() is invoked.
Fixes: ab03eff58e ("xprtrdma: Add trace points in RPC Call transmit paths")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Commit e28ce90083 ("xprtrdma: kmalloc rpcrdma_ep separate from
rpcrdma_xprt") erroneously removed a xprt_force_disconnect()
call from the "transport disconnect" path. The result was that the
client no longer responded to server-side disconnect requests.
Restore that call.
Fixes: e28ce90083 ("xprtrdma: kmalloc rpcrdma_ep separate from rpcrdma_xprt")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
When ESP encapsulation is enabled on a TCP socket, I'm replacing the
existing ->sk_destruct callback with espintcp_destruct. We still need to
call the old callback to perform the other cleanups when the socket is
destroyed. Save the old callback, and call it from espintcp_destruct.
Fixes: e27cca96cd ("xfrm: add espintcp (RFC 8229)")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This xfrm_state_put call in esp4/6_gro_receive() will cause
double put for state, as in out_reset path secpath_reset()
will put all states set in skb sec_path.
So fix it by simply remove the xfrm_state_put call.
Fixes: 6ed69184ed ("xfrm: Reset secpath in xfrm failure")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We need to set sk_state to CLOSED, else we will get following:
IPv4: Attempt to release TCP socket in state 3 00000000b95f109e
IPv4: Attempt to release TCP socket in state 10 00000000b95f109e
First one is from inet_sock_destruct(), second one from
mptcp_sk_clone failure handling. Setting sk_state to CLOSED isn't
enough, we also need to orphan sk so it has DEAD flag set.
Otherwise, a very similar warning is printed from inet_sock_destruct().
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following snippet (replicated from syzkaller reproducer) generates
warning: "IPv4: Attempt to release TCP socket in state 1".
int main(void) {
struct sockaddr_in sin1 = { .sin_family = 2, .sin_port = 0x4e20,
.sin_addr.s_addr = 0x010000e0, };
struct sockaddr_in sin2 = { .sin_family = 2,
.sin_addr.s_addr = 0x0100007f, };
struct sockaddr_in sin3 = { .sin_family = 2, .sin_port = 0x4e20,
.sin_addr.s_addr = 0x0100007f, };
int r0 = socket(0x2, 0x1, 0x106);
int r1 = socket(0x2, 0x1, 0x106);
bind(r1, (void *)&sin1, sizeof(sin1));
connect(r1, (void *)&sin2, sizeof(sin2));
listen(r1, 3);
return connect(r0, (void *)&sin3, 0x4d);
}
Reason is that the newly generated mptcp socket is closed via the ulp
release of the tcp listener socket when its accept backlog gets purged.
To fix this, delay setting the ESTABLISHED state until after userspace
calls accept and via mptcp specific destructor.
Fixes: 58b0991962 ("mptcp: create msk early")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/9
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it impossible that cmpri or cmpre values are set to the
value 16 which is not possible, because these are 4 bit values. We
currently run in an overflow when assigning the value 16 to it.
According to the standard a value of 16 can be interpreted as a full
elided address which isn't possible to set as compression value. A reason
why this cannot be set is that the current ipv6 header destination address
should never show up inside the segments of the rpl header. In this case we
run in a overflow and the address will have no compression at all. Means
cmpri or compre is set to 0.
As we handle cmpri and cmpre sometimes as unsigned char or 4 bit value
inside the rpl header the current behaviour ends in an invalid header
format. This patch simple use the best compression method if we ever run
into the case that the destination address is showed up inside the rpl
segments. We avoid the overflow handling and the rpl header is still valid,
even when we have the destination address inside the rpl segments.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_rcv() invokes tipc_node_find() twice, which returns a reference of
the specified tipc_node object to "n" with increased refcnt.
When tipc_rcv() returns or a new object is assigned to "n", the original
local reference of "n" becomes invalid, so the refcount should be
decreased to keep refcount balanced.
The issue happens in some paths of tipc_rcv(), which forget to decrease
the refcnt increased by tipc_node_find() and will cause a refcnt leak.
Fix this issue by calling tipc_node_put() before the original object
pointed by "n" becomes invalid.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_crypto_rcv() invokes tipc_aead_get(), which returns a reference of
the tipc_aead object to "aead" with increased refcnt.
When tipc_crypto_rcv() returns, the original local reference of "aead"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.
The issue happens in one error path of tipc_crypto_rcv(). When TIPC
message decryption status is EINPROGRESS or EBUSY, the function forgets
to decrease the refcnt increased by tipc_aead_get() and causes a refcnt
leak.
Fix this issue by calling tipc_aead_put() on the error path when TIPC
message decryption status is EINPROGRESS or EBUSY.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nr_add_node() invokes nr_neigh_get_dev(), which returns a local
reference of the nr_neigh object to "nr_neigh" with increased refcnt.
When nr_add_node() returns, "nr_neigh" becomes invalid, so the refcount
should be decreased to keep refcount balanced.
The issue happens in one normal path of nr_add_node(), which forgets to
decrease the refcnt increased by nr_neigh_get_dev() and causes a refcnt
leak. It should decrease the refcnt before the function returns like
other normal paths do.
Fix this issue by calling nr_neigh_put() before the nr_add_node()
returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the xpo_release_rqst transport method to ensure that each
rqstp's svc_rdma_recv_ctxt object is released even when the server
cannot return a Reply for that rqstp.
Without this fix, each RPC whose Reply cannot be sent leaks one
svc_rdma_recv_ctxt. This is a 2.5KB structure, a 4KB DMA-mapped
Receive buffer, and any pages that might be part of the Reply
message.
The leak is infrequent unless the network fabric is unreliable or
Kerberos is in use, as GSS sequence window overruns, which result
in connection loss, are more common on fast transports.
Fixes: 3a88092ee3 ("svcrdma: Preserve Receive buffer until svc_rdma_sendto")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Currently, after the forward channel connection goes away,
backchannel operations are causing soft lockups on the server
because call_transmit_status's SOFTCONN logic ignores ENOTCONN.
Such backchannel Calls are aggressively retried until the client
reconnects.
Backchannel Calls should use RPC_TASK_NOCONNECT rather than
RPC_TASK_SOFTCONN. If there is no forward connection, the server is
not capable of establishing a connection back to the client, thus
that backchannel request should fail before the server attempts to
send it. Commit 58255a4e3c ("NFSD: NFSv4 callback client should
use RPC_TASK_SOFTCONN") was merged several years before
RPC_TASK_NOCONNECT was available.
Because setup_callback_client() explicitly sets NOPING, the NFSv4.0
callback connection depends on the first callback RPC to initiate
a connection to the client. Thus NFSv4.0 needs to continue to use
RPC_TASK_SOFTCONN.
Suggested-by: Trond Myklebust <trondmy@hammerspace.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: <stable@vger.kernel.org> # v4.20+
Pull networking fixes from David Miller:
1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.
2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet.
3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing.
4) Adjust icmp6 message source address selection when routes have a
preferred source address set, from Tim Stallard.
5) Be sure to validate HSR protocol version when creating new links,
from Taehee Yoo.
6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in
non-initial namespaces, from Michael Weiß.
7) Missing release firmware call in mlx5, from Eran Ben Elisha.
8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from
Taehee Yoo.
9) Fix pause frame negotiation in marvell phy driver, from Clemens
Gruber.
10) Record RX queue early enough in tun packet paths such that XDP
programs will see the correct RX queue index, from Gilberto Bertin.
11) Fix double unlock in mptcp, from Florian Westphal.
12) Fix offset overflow in ARM bpf JIT, from Luke Nelson.
13) marvell10g needs to soft reset PHY when coming out of low power
mode, from Russell King.
14) Fix MTU setting regression in stmmac for some chip types, from
Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
amd-xgbe: Use __napi_schedule() in BH context
mISDN: make dmril and dmrim static
net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes
net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode
tipc: fix incorrect increasing of link window
Documentation: Fix tcp_challenge_ack_limit default value
net: tulip: make early_486_chipsets static
dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400
ipv6: remove redundant assignment to variable err
net/rds: Use ERR_PTR for rds_message_alloc_sgs()
net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
selftests/bpf: Check for correct program attach/detach in xdp_attach test
libbpf: Fix type of old_fd in bpf_xdp_set_link_opts
libbpf: Always specify expected_attach_type on program load if supported
xsk: Add missing check on user supplied headroom size
mac80211: fix channel switch trigger from unknown mesh peer
mac80211: fix race in ieee80211_register_hw()
net: marvell10g: soft-reset the PHY when coming out of low power
net: marvell10g: report firmware version
net/cxgb4: Check the return from t4_query_params properly
...
In commit 16ad3f4022 ("tipc: introduce variable window congestion
control"), we allow link window to change with the congestion avoidance
algorithm. However, there is a bug that during the slow-start if packet
retransmission occurs, the link will enter the fast-recovery phase, set
its window to the 'ssthresh' which is never less than 300, so the link
window suddenly increases to that limit instead of decreasing.
Consequently, two issues have been observed:
- For broadcast-link: it can leave a gap between the link queues that a
new packet will be inserted and sent before the previous ones, i.e. not
in-order.
- For unicast: the algorithm does not work as expected, the link window
jumps to the slow-start threshold whereas packet retransmission occurs.
This commit fixes the issues by avoiding such the link window increase,
but still decreasing if the 'ssthresh' is lowered.
Fixes: 16ad3f4022 ("tipc: introduce variable window congestion control")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable err is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning the error code via a 'int *ret' when the function returns a
pointer is very un-kernely and causes gcc 10's static analysis to choke:
net/rds/message.c: In function ‘rds_message_map_pages’:
net/rds/message.c:358:10: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
358 | return ERR_PTR(ret);
Use a typical ERR_PTR return instead.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2020-04-15
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 3 day(s) which contain
a total of 11 files changed, 238 insertions(+), 95 deletions(-).
The main changes are:
1) Fix offset overflow for BPF_MEM BPF_DW insn mapping on arm32 JIT,
from Luke Nelson and Xi Wang.
2) Prevent mprotect() to make frozen & mmap()'ed BPF map writeable
again, from Andrii Nakryiko and Jann Horn.
3) Fix type of old_fd in bpf_xdp_set_link_opts to int in libbpf and add
selftests, from Toke Høiland-Jørgensen.
4) Fix AF_XDP to check that headroom cannot be larger than the available
space in the chunk, from Magnus Karlsson.
5) Fix reset of XDP prog when expected_fd is set, from David Ahern.
6) Fix a segfault in bpftool's struct_ops command when BTF is not
available, from Daniel T. Lee.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* FTM responder policy netlink validation fix
(but the only user validates again later)
* kernel-doc fixes
* a fix for a race in mac80211 radio registration vs. userspace
* a mesh channel switch fix
* a fix for a syzbot reported kasprintf() issue
-----BEGIN PGP SIGNATURE-----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=1yy8
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2020-04-15' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A couple of fixes:
* FTM responder policy netlink validation fix
(but the only user validates again later)
* kernel-doc fixes
* a fix for a race in mac80211 radio registration vs. userspace
* a mesh channel switch fix
* a fix for a syzbot reported kasprintf() issue
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a check that the headroom cannot be larger than the available
space in the chunk. In the current code, a malicious user can set the
headroom to a value larger than the chunk size minus the fixed XDP
headroom. That way packets with a length larger than the supported
size in the umem could get accepted and result in an out-of-bounds
write.
Fixes: c0c77d8fb7 ("xsk: add user memory registration support sockopt")
Reported-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=207225
Link: https://lore.kernel.org/bpf/1586849715-23490-1-git-send-email-magnus.karlsson@intel.com
Previously mesh channel switch happens if beacon contains
CSA IE without checking the mesh peer info. Due to that
channel switch happens even if the beacon is not from
its own mesh peer. Fixing that by checking if the CSA
originated from the same mesh network before proceeding
for channel switch.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1585403604-29274-1-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For transport mode, when ipv6 nexthdr is set, the packet format might
be like:
----------------------------------------------------
| | dest | | | | ESP | ESP |
| IP6 hdr| opts.| ESP | TCP | Data | Trailer | ICV |
----------------------------------------------------
What it wants to get for x-proto in esp6_gso_encap() is the proto that
will be set in ESP nexthdr. So it should skip all ipv6 nexthdrs and
get the real transport protocol. Othersize, the wrong proto number
will be set into ESP nexthdr.
This patch is to skip all ipv6 nexthdrs by calling ipv6_skip_exthdr()
in esp6_gso_encap().
Fixes: 7862b4058b ("esp: Add gso handlers for esp4 and esp6")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
For transport mode, when ipv6 nexthdr is set, the packet format might
be like:
----------------------------------------------------
| | dest | | | | ESP | ESP |
| IP6 hdr| opts.| ESP | TCP | Data | Trailer | ICV |
----------------------------------------------------
and in __xfrm_transport_prep():
pskb_pull(skb, skb->mac_len + sizeof(ip6hdr) + x->props.header_len);
it will pull the data pointer to the wrong position, as it missed the
nexthdrs/dest opts.
This patch is to fix it by using:
pskb_pull(skb, skb_transport_offset(skb) + x->props.header_len);
as we can be sure transport_header points to ESP header at that moment.
It also fixes a panic when packets with ipv6 nexthdr are sent over
esp6 transport mode:
[ 100.473845] kernel BUG at net/core/skbuff.c:4325!
[ 100.478517] RIP: 0010:__skb_to_sgvec+0x252/0x260
[ 100.494355] Call Trace:
[ 100.494829] skb_to_sgvec+0x11/0x40
[ 100.495492] esp6_output_tail+0x12e/0x550 [esp6]
[ 100.496358] esp6_xmit+0x1d5/0x260 [esp6_offload]
[ 100.498029] validate_xmit_xfrm+0x22f/0x2e0
[ 100.499604] __dev_queue_xmit+0x589/0x910
[ 100.502928] ip6_finish_output2+0x2a5/0x5a0
[ 100.503718] ip6_output+0x6c/0x120
[ 100.505198] xfrm_output_resume+0x4bf/0x530
[ 100.508683] xfrm6_output+0x3a/0xc0
[ 100.513446] inet6_csk_xmit+0xa1/0xf0
[ 100.517335] tcp_sendmsg+0x27/0x40
[ 100.517977] sock_sendmsg+0x3e/0x60
[ 100.518648] __sys_sendto+0xee/0x160
Fixes: c35fe4106b ("xfrm: Add mode handlers for IPsec on layer 2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
For beet mode, when it's ipv6 inner address with nexthdrs set,
the packet format might be:
----------------------------------------------------
| outer | | dest | | | ESP | ESP |
| IP hdr | ESP | opts.| TCP | Data | Trailer | ICV |
----------------------------------------------------
The nexthdr from ESP could be NEXTHDR_HOP(0), so it should
continue processing the packet when nexthdr returns 0 in
xfrm_input(). Otherwise, when ipv6 nexthdr is set, the
packet will be dropped.
I don't see any error cases that nexthdr may return 0. So
fix it by removing the check for nexthdr == 0.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
A race condition leading to a kernel crash is observed during invocation
of ieee80211_register_hw() on a dragonboard410c device having wcn36xx
driver built as a loadable module along with a wifi manager in user-space
waiting for a wifi device (wlanX) to be active.
Sequence diagram for a particular kernel crash scenario:
user-space ieee80211_register_hw() ieee80211_tasklet_handler()
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
| | |
|<---phy0----wiphy_register() |
|-----iwd if_add---->| |
| |<---IRQ----(RX packet)
| Kernel crash |
| due to unallocated |
| workqueue. |
| | |
| alloc_ordered_workqueue() |
| | |
| Misc wiphy init. |
| | |
| ieee80211_if_add() |
| | |
As evident from above sequence diagram, this race condition isn't specific
to a particular wifi driver but rather the initialization sequence in
ieee80211_register_hw() needs to be fixed. So re-order the initialization
sequence and the updated sequence diagram would look like:
user-space ieee80211_register_hw() ieee80211_tasklet_handler()
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
| | |
| alloc_ordered_workqueue() |
| | |
| Misc wiphy init. |
| | |
|<---phy0----wiphy_register() |
|-----iwd if_add---->| |
| |<---IRQ----(RX packet)
| | |
| ieee80211_if_add() |
| | |
Cc: stable@vger.kernel.org
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/1586254255-28713-1-git-send-email-sumit.garg@linaro.org
[Johannes: fix rtnl imbalances]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
DSA and CPU ports can be configured in two ways. By default, the
driver should configure such ports to there maximum bandwidth. For
most use cases, this is sufficient. When this default is insufficient,
a phylink instance can be bound to such ports, and phylink will
configure the port, e.g. based on fixed-link properties. phylink
assumes the port is initially down. Given that the driver should have
already configured it to its maximum speed, ask the driver to down
the port before instantiating the phylink instance.
Fixes: 30c4a5b0aa ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the DATA packet transmission to disable nofrag for UDPv4 on an AF_INET6
socket as well as UDPv6 when trying to transmit fragmentably.
Without this, packets filled to the normal size used by the kernel AFS
client of 1412 bytes be rejected by udp_sendmsg() with EMSGSIZE
immediately. The ->sk_error_report() notification hook is called, but
rxrpc doesn't generate a trace for it.
This is a temporary fix; a more permanent solution needs to involve
changing the size of the packets being filled in accordance with the MTU,
which isn't currently done in AF_RXRPC. The reason for not doing so was
that, barring the last packet in an rx jumbo packet, jumbos can only be
assembled out of 1412-byte packets - and the plan was to construct jumbos
on the fly at transmission time.
Also, there's no point turning on IPV6_MTU_DISCOVER, since IPv6 has to
engage in this anyway since fragmentation is only done by the sender. We
can then condense the switch-statement in rxrpc_send_data_packet().
Fixes: 75b54cb57c ("rxrpc: Add IPv6 support")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free block_cb memory when asked to be deleted.
Fixes: 978703f425 ("netfilter: flowtable: Add API for registering to flow table events")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The commit mentioned in the Fixes tag reuses the local prog variable
when looking up an expected_fd. The variable is not reset when fd < 0
causing a detach with the expected_fd set to actually call
dev_xdp_install for the existing program. The end result is that the
detach does not happen.
Fixes: 92234c8f15 ("xdp: Support specifying expected existing program when attaching XDP")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200412133204.43847-1-dsahern@kernel.org
Deleting list entry within hlist_for_each_entry_safe is not safe unless
next pointer (tmp) is protected too. It's not, because once hash_lock
is released, cache_clean may delete the entry that tmp points to. Then
cache_purge can walk to a deleted entry and tries to double free it.
Fix this bug by holding only the deleted entry's reference.
Suggested-by: NeilBrown <neilb@suse.de>
Signed-off-by: Yihao Wu <wuyihao@linux.alibaba.com>
Reviewed-by: NeilBrown <neilb@suse.de>
[ cel: removed unused variable ]
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
mptcp_connect/28740 is trying to release lock (sk_lock-AF_INET) at:
[<ffffffff82c15869>] mptcp_poll+0xb9/0x550
but there are no more locks to release!
Call Trace:
lock_release+0x50f/0x750
release_sock+0x171/0x1b0
mptcp_poll+0xb9/0x550
sock_poll+0x157/0x470
? get_net_ns+0xb0/0xb0
do_sys_poll+0x63c/0xdd0
Problem is that __mptcp_tcp_fallback() releases the mptcp socket lock,
but after recent change it doesn't do this in all of its return paths.
To fix this, remove the unlock from __mptcp_tcp_fallback() and
always do the unlock in the caller.
Also add a small comment as to why we have this
__mptcp_needs_tcp_fallback().
Fixes: 0b4f33def7 ("mptcp: fix tcp fallback crash")
Reported-by: syzbot+e56606435b7bfeea8cf5@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- raise minimum supported binutils version to 2.23
- remove old CONFIG_AS_* macros that we know binutils >= 2.23 supports
- move remaining CONFIG_AS_* tests to Kconfig from Makefile
- enable -Wtautological-compare warnings to catch more issues
- do not support GCC plugins for GCC <= 4.7
- fix various breakages of 'make xconfig'
- include the linker version used for linking the kernel into
LINUX_COMPILER, which is used for the banner, and also exposed to
/proc/version
- link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y,
which allows us to remove the lib-ksyms.o workaround, and to
solve the last known issue of the LLVM linker
- add dummy tools in scripts/dummy-tools/ to enable all compiler
tests in Kconfig, which will be useful for distro maintainers
- support the single switch, LLVM=1 to use Clang and all LLVM utilities
instead of GCC and Binutils.
- support LLVM_IAS=1 to enable the integrated assembler, which is still
experimental
-----BEGIN PGP SIGNATURE-----
iQJJBAABCgAzFiEEbmPs18K1szRHjPqEPYsBB53g2wYFAl6RNqEVHG1hc2FoaXJv
eUBrZXJuZWwub3JnAAoJED2LAQed4NsGZPEP/3affmzIWJuKGF1RErOHK3KCe/uX
PmLjoRZ7im7V+J4b3W+p+re6BOXIXhW+rtKoP/Ijuys9g80WeeAb2nB4h0ESOtff
3NgN97v28mh4tVtbluJambFDXItei+UwDp1sgg2sZ7ehaSBVny9hgNmPRn5YcyoS
O3Juy85q70l8awBWThjEHgSxEw2Rzh9PLE6YmMt40rHTxVEDjMOPSuBlp/+TWj3X
ugF/wInp+J5mCAKCwJI4L6PavdwIwf9hg3Cv/DpoOw60TxwH+7Rq6RueDKBgHhe3
UEPHrXyPCsF/JQwwSFxN7k481RV2PjkXFwA3U5vH+3WIRb4ETX0+fmBIrLPSAX4z
6rZiEvdrGS4TVvW2i8mrkJUrLPHNyQ90q/FU0V18A1k77Cv7mWJjSebTAVYNvz/v
f/DxApaepwprdtHcNYJMN/TVnwxNexJK+U+bkuXsmDggvZYCxwLQUjtI3Sab1Rv9
C6Y8WgqKx8yP6NbqVtUMkwXdEhBiHgybVxkl9hseUEbhUElIViuq5rlrHa0FVt2Q
w4orgFXOd7k5iuDr7ka+wa3p20KLQQuB+vwLaCpi35+4vepQ7P0i2tFNwSclo7lO
+iNy4Bq20W0/cmQeUJIzctJGibwro1I3HPN1UJ7gp0fZ2WVGzV0SKpwQ0tLOVuuU
y9yPsL1ciDpKQKMh
=jpyF
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- raise minimum supported binutils version to 2.23
- remove old CONFIG_AS_* macros that we know binutils >= 2.23 supports
- move remaining CONFIG_AS_* tests to Kconfig from Makefile
- enable -Wtautological-compare warnings to catch more issues
- do not support GCC plugins for GCC <= 4.7
- fix various breakages of 'make xconfig'
- include the linker version used for linking the kernel into
LINUX_COMPILER, which is used for the banner, and also exposed to
/proc/version
- link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y, which
allows us to remove the lib-ksyms.o workaround, and to solve the last
known issue of the LLVM linker
- add dummy tools in scripts/dummy-tools/ to enable all compiler tests
in Kconfig, which will be useful for distro maintainers
- support the single switch, LLVM=1 to use Clang and all LLVM utilities
instead of GCC and Binutils.
- support LLVM_IAS=1 to enable the integrated assembler, which is still
experimental
* tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (36 commits)
kbuild: fix comment about missing include guard detection
kbuild: support LLVM=1 to switch the default tools to Clang/LLVM
kbuild: replace AS=clang with LLVM_IAS=1
kbuild: add dummy toolchains to enable all cc-option etc. in Kconfig
kbuild: link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y
MIPS: fw: arc: add __weak to prom_meminit and prom_free_prom_memory
kbuild: remove -I$(srctree)/tools/include from scripts/Makefile
kbuild: do not pass $(KBUILD_CFLAGS) to scripts/mkcompile_h
Documentation/llvm: fix the name of llvm-size
kbuild: mkcompile_h: Include $LD version in /proc/version
kconfig: qconf: Fix a few alignment issues
kconfig: qconf: remove some old bogus TODOs
kconfig: qconf: fix support for the split view mode
kconfig: qconf: fix the content of the main widget
kconfig: qconf: Change title for the item window
kconfig: qconf: clean deprecated warnings
gcc-plugins: drop support for GCC <= 4.7
kbuild: Enable -Wtautological-compare
x86: update AS_* macros to binutils >=2.23, supporting ADX and AVX2
crypto: x86 - clean up poly1305-x86_64-cryptogams.S by 'make clean'
...
Daniel Borkmann says:
====================
pull-request: bpf 2020-04-10
The following pull-request contains BPF updates for your *net* tree.
We've added 13 non-merge commits during the last 7 day(s) which contain
a total of 13 files changed, 137 insertions(+), 43 deletions(-).
The main changes are:
1) JIT code emission fixes for riscv and arm32, from Luke Nelson and Xi Wang.
2) Disable vmlinux BTF info if GCC_PLUGIN_RANDSTRUCT is used, from Slava Bacherikov.
3) Fix oob write in AF_XDP when meta data is used, from Li RongQing.
4) Fix bpf_get_link_xdp_id() handling on single prog when flags are specified,
from Andrey Ignatov.
5) Fix sk_assign() BPF helper for request sockets that can have sk_reuseport
field uninitialized, from Joe Stringer.
6) Fix mprotect() test case for the BPF LSM, from KP Singh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_IP_MULTICAST is not set and multicast ip is added to the device
with autojoin flag or when multicast ip is deleted kernel will crash.
steps to reproduce:
ip addr add 224.0.0.0/32 dev eth0
ip addr del 224.0.0.0/32 dev eth0
or
ip addr add 224.0.0.0/32 dev eth0 autojoin
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000088
pc : _raw_write_lock_irqsave+0x1e0/0x2ac
lr : lock_sock_nested+0x1c/0x60
Call trace:
_raw_write_lock_irqsave+0x1e0/0x2ac
lock_sock_nested+0x1c/0x60
ip_mc_config.isra.28+0x50/0xe0
inet_rtm_deladdr+0x1a8/0x1f0
rtnetlink_rcv_msg+0x120/0x350
netlink_rcv_skb+0x58/0x120
rtnetlink_rcv+0x14/0x20
netlink_unicast+0x1b8/0x270
netlink_sendmsg+0x1a0/0x3b0
____sys_sendmsg+0x248/0x290
___sys_sendmsg+0x80/0xc0
__sys_sendmsg+0x68/0xc0
__arm64_sys_sendmsg+0x20/0x30
el0_svc_common.constprop.2+0x88/0x150
do_el0_svc+0x20/0x80
el0_sync_handler+0x118/0x190
el0_sync+0x140/0x180
Fixes: 93a714d6b5 ("multicast: Extend ip address command to enable multicast group join/leave on")
Signed-off-by: Taras Chornyi <taras.chornyi@plvision.eu>
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rds_free_mr(), it calls rds_destroy_mr(mr) directly. But this
defeats the purpose of reference counting and makes MR free handling
impossible. It means that holding a reference does not guarantee that
it is safe to access some fields. For example, In
rds_cmsg_rdma_dest(), it increases the ref count, unlocks and then
calls mr->r_trans->sync_mr(). But if rds_free_mr() (and
rds_destroy_mr()) is called in between (there is no lock preventing
this to happen), r_trans_private is set to NULL, causing a panic.
Similar issue is in rds_rdma_unuse().
Reported-by: zerons <sironhide0null@gmail.com>
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And removed rds_mr_put().
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable ret is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the local node id(qrtr_local_nid) is not modified after its
initialization, it equals to the broadcast node id(QRTR_NODE_BCAST).
So the messages from local node should not be taken as broadcast
and keep the process going to send them out anyway.
The definitions are as follow:
static unsigned int qrtr_local_nid = NUMA_NO_NODE;
Fixes: fdf5fd3975 ("net: qrtr: Broadcast messages only from control port")
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- support for asynchronous create and unlink (Jeff Layton). Creates
and unlinks are satisfied locally, without waiting for a reply from
the MDS, provided the client has been granted appropriate caps (new
in v15.y.z ("Octopus") release). This can be a big help for metadata
heavy workloads such as tar and rsync. Opt-in with the new nowsync
mount option.
- multiple blk-mq queues for rbd (Hannes Reinecke and myself). When
the driver was converted to blk-mq, we settled on a single blk-mq
queue because of a global lock in libceph and some other technical
debt. These have since been addressed, so allocate a queue per CPU
to enhance parallelism.
- don't hold onto caps that aren't actually needed (Zheng Yan). This
has been our long-standing behavior, but it causes issues with some
active/standby applications (synchronous I/O, stalls if the standby
goes down, etc).
- .snap directory timestamps consistent with ceph-fuse (Luis Henriques)
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAl6OEO4THGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi0XNB/wItYipkjlL5fIUBqiRWzYai72DWdPp
CnOZo8LB+O0MQDomPT6DdpU1OMlWZi5HF7zklrZ35LTm21UkRNC9zvccjs9l66PJ
qo9cKJbxxju+hgzIvgvK9PjlDlaiFAc/pkF8lZ/NaOnSsM1vvsFL9IuY2LXS38MY
A/uUTZNUnFy5udam8TPuN+gWwZcUIH48lRWQLWe2I/hNJSweX1l8OHvecOBg+cYH
G+8vb7mLU2V9ky0YT5JJmVxUV3CWA5wH6ZrWWy1ofVDdeSFLPrhgWX6IMjaNq+Gd
xPfxmly47uBviSqON9dMkiThgy0Qj7yi0Pvx+1sAZbD7aj/6A4qg3LX5
=GIX0
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.7-rc1' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"The main items are:
- support for asynchronous create and unlink (Jeff Layton).
Creates and unlinks are satisfied locally, without waiting for a
reply from the MDS, provided the client has been granted
appropriate caps (new in v15.y.z ("Octopus") release). This can be
a big help for metadata heavy workloads such as tar and rsync.
Opt-in with the new nowsync mount option.
- multiple blk-mq queues for rbd (Hannes Reinecke and myself).
When the driver was converted to blk-mq, we settled on a single
blk-mq queue because of a global lock in libceph and some other
technical debt. These have since been addressed, so allocate a
queue per CPU to enhance parallelism.
- don't hold onto caps that aren't actually needed (Zheng Yan).
This has been our long-standing behavior, but it causes issues with
some active/standby applications (synchronous I/O, stalls if the
standby goes down, etc).
- .snap directory timestamps consistent with ceph-fuse (Luis
Henriques)"
* tag 'ceph-for-5.7-rc1' of git://github.com/ceph/ceph-client: (49 commits)
ceph: fix snapshot directory timestamps
ceph: wait for async creating inode before requesting new max size
ceph: don't skip updating wanted caps when cap is stale
ceph: request new max size only when there is auth cap
ceph: cleanup return error of try_get_cap_refs()
ceph: return ceph_mdsc_do_request() errors from __get_parent()
ceph: check all mds' caps after page writeback
ceph: update i_requested_max_size only when sending cap msg to auth mds
ceph: simplify calling of ceph_get_fmode()
ceph: remove delay check logic from ceph_check_caps()
ceph: consider inode's last read/write when calculating wanted caps
ceph: always renew caps if mds_wanted is insufficient
ceph: update dentry lease for async create
ceph: attempt to do async create when possible
ceph: cache layout in parent dir on first sync create
ceph: add new MDS req field to hold delegated inode number
ceph: decode interval_sets for delegated inos
ceph: make ceph_fill_inode non-static
ceph: perform asynchronous unlink if we have sufficient caps
ceph: don't take refs to want mask unless we have all bits
...
In testing, we found that for request sockets the sk->sk_reuseport field
may yet be uninitialized, which caused bpf_sk_assign() to randomly
succeed or return -ESOCKTNOSUPPORT when handling the forward ACK in a
three-way handshake.
Fix it by only applying the reuseport check for full sockets.
Fixes: cf7fbe660f ("bpf: Add socket assign support")
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200408033540.10339-1-joe@wand.net.nz
Building with some experimental patches, I came across a warning
in the tls code:
include/linux/compiler.h:215:30: warning: assignment discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
215 | *(volatile typeof(x) *)&(x) = (val); \
| ^
net/tls/tls_main.c:650:4: note: in expansion of macro 'smp_store_release'
650 | smp_store_release(&saved_tcpv4_prot, prot);
This appears to be a legitimate warning about assigning a const pointer
into the non-const 'saved_tcpv4_prot' global. Annotate both the ipv4 and
ipv6 pointers 'const' to make the code internally consistent.
Fixes: 5bb4c45d46 ("net/tls: Read sk_prot once when building tls proto ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creation and management of L2TPv3 tunnels and session through netlink
requires CAP_NET_ADMIN. However, a process with CAP_NET_ADMIN in a
non-initial user namespace gets an EPERM due to the use of the
genetlink GENL_ADMIN_PERM flag. Thus, management of L2TP VPNs inside
an unprivileged container won't work.
We replaced the GENL_ADMIN_PERM by the GENL_UNS_ADMIN_PERM flag
similar to other network modules which also had this problem, e.g.,
openvswitch (commit 4a92602aa1 "openvswitch: allow management from
inside user namespaces") and nl80211 (commit 5617c6cd6f "nl80211:
Allow privileged operations from user namespaces").
I tested this in the container runtime trustm3 (trustm3.github.io)
and was able to create l2tp tunnels and sessions in unpriviliged
(user namespaced) containers using a private network namespace.
For other runtimes such as docker or lxc this should work, too.
Signed-off-by: Michael Weiß <michael.weiss@aisec.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the kernel specifies binutils 2.23 as the minimum version, we
can remove ifdefs for AVX2 and ADX throughout.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Doing this probing inside of the Makefiles means we have a maze of
ifdefs inside the source code and child Makefiles that need to make
proper decisions on this too. Instead, we do it at Kconfig time, like
many other compiler and assembler options, which allows us to set up the
dependencies normally for full compilation units. In the process, the
ADX test changes to use %eax instead of %r10 so that it's valid in both
32-bit and 64-bit mode.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
In the current hsr code, only 0 and 1 protocol versions are valid.
But current hsr code doesn't check the version, which is received by
userspace.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1 version 4
In the test commands, version 4 is invalid.
So, the command should be failed.
After this patch, following error will occur.
"Error: hsr: Only versions 0..1 are supported."
Fixes: ee1c279772 ("net/hsr: Added support for HSR v1")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After driver sets the missed chain on the tc skb extension it is
consumed (deleted) by tc_classify_ingress and tc jumps to that chain.
If tc now misses on this chain (either no match, or no goto action),
then last executed chain remains 0, and the skb extension is not re-added,
and the next datapath (ovs) will start from 0.
Fix that by setting last executed chain to the chain read from the skb
extension, so if there is a miss, we set it back.
Fixes: af699626ee ("net: sched: Support specifying a starting chain via tc skb ext")
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For HZ < 1000 timeout 2000us rounds up to 1 jiffy but expires randomly
because next timer interrupt could come shortly after starting softirq.
For commonly used CONFIG_HZ=1000 nothing changes.
Fixes: 7acf8a1e8a ("Replace 2 jiffies with sysctl netdev_budget_usecs to enable softirq tuning")
Reported-by: Dmitry Yakunin <zeil@yandex-team.ru>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit fac6fce9bd ("net: icmp6: provide input address for
traceroute6") ICMPv6 errors have source addresses from the ingress
interface. However, this overrides when source address selection is
influenced by setting preferred source addresses on routes.
This can result in ICMP errors being lost to upstream BCP38 filters
when the wrong source addresses are used, breaking path MTU discovery
and traceroute.
This patch sets the modified source address selection to only take place
when the route used has no prefsrc set.
It can be tested with:
ip link add v1 type veth peer name v2
ip netns add test
ip netns exec test ip link set lo up
ip link set v2 netns test
ip link set v1 up
ip netns exec test ip link set v2 up
ip addr add 2001:db8::1/64 dev v1 nodad
ip addr add 2001:db8::3 dev v1 nodad
ip netns exec test ip addr add 2001:db8::2/64 dev v2 nodad
ip netns exec test ip route add unreachable 2001:db8:1::1
ip netns exec test ip addr add 2001:db8:100::1 dev lo
ip netns exec test ip route add 2001:db8::1 dev v2 src 2001:db8:100::1
ip route add 2001:db8:1000::1 via 2001:db8::2
traceroute6 -s 2001:db8::1 2001:db8:1000::1
traceroute6 -s 2001:db8::3 2001:db8:1000::1
ip netns delete test
Output before:
$ traceroute6 -s 2001:db8::1 2001:db8:1000::1
traceroute to 2001:db8:1000::1 (2001:db8:1000::1), 30 hops max, 80 byte packets
1 2001:db8::2 (2001:db8::2) 0.843 ms !N 0.396 ms !N 0.257 ms !N
$ traceroute6 -s 2001:db8::3 2001:db8:1000::1
traceroute to 2001:db8:1000::1 (2001:db8:1000::1), 30 hops max, 80 byte packets
1 2001:db8::2 (2001:db8::2) 0.772 ms !N 0.257 ms !N 0.357 ms !N
After:
$ traceroute6 -s 2001:db8::1 2001:db8:1000::1
traceroute to 2001:db8:1000::1 (2001:db8:1000::1), 30 hops max, 80 byte packets
1 2001:db8:100::1 (2001:db8:100::1) 8.885 ms !N 0.310 ms !N 0.174 ms !N
$ traceroute6 -s 2001:db8::3 2001:db8:1000::1
traceroute to 2001:db8:1000::1 (2001:db8:1000::1), 30 hops max, 80 byte packets
1 2001:db8::2 (2001:db8::2) 1.403 ms !N 0.205 ms !N 0.313 ms !N
Fixes: fac6fce9bd ("net: icmp6: provide input address for traceroute6")
Signed-off-by: Tim Stallard <code@timstallard.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net, they are:
1) Fix spurious overlap condition in the rbtree tree, from Stefano Brivio.
2) Fix possible uninitialized pointer dereference in nft_lookup.
3) IDLETIMER v1 target matches the Android layout, from
Maciej Zenczykowski.
4) Dangling pointer in nf_tables_set_alloc_name, from Eric Dumazet.
5) Fix RCU warning splat in ipset find_set_type(), from Amol Grover.
6) Report EOPNOTSUPP on unsupported set flags and object types in sets.
7) Add NFT_SET_CONCAT flag to provide consistent error reporting
when users defines set with ranges in concatenations in old kernels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include:
Stable fixes:
- Fix a page leak in nfs_destroy_unlinked_subrequests()
- Fix use-after-free issues in nfs_pageio_add_request()
- Fix new mount code constant_table array definitions
- finish_automount() requires us to hold 2 refs to the mount record
Features:
- Improve the accuracy of telldir/seekdir by using 64-bit cookies when
possible.
- Allow one RDMA active connection and several zombie connections to
prevent blocking if the remote server is unresponsive.
- Limit the size of the NFS access cache by default
- Reduce the number of references to credentials that are taken by NFS
- pNFS files and flexfiles drivers now support per-layout segment
COMMIT lists.
- Enable partial-file layout segments in the pNFS/flexfiles driver.
- Add support for CB_RECALL_ANY to the pNFS flexfiles layout type
- pNFS/flexfiles Report NFS4ERR_DELAY and NFS4ERR_GRACE errors from
the DS using the layouterror mechanism.
Bugfixes and cleanups:
- SUNRPC: Fix krb5p regressions
- Don't specify NFS version in "UDP not supported" error
- nfsroot: set tcp as the default transport protocol
- pnfs: Return valid stateids in nfs_layout_find_inode_by_stateid()
- alloc_nfs_open_context() must use the file cred when available
- Fix locking when dereferencing the delegation cred
- Fix memory leaks in O_DIRECT when nfs_get_lock_context() fails
- Various clean ups of the NFS O_DIRECT commit code
- Clean up RDMA connect/disconnect
- Replace zero-length arrays with C99-style flexible arrays
-----BEGIN PGP SIGNATURE-----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=YUcP
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.7-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Stable fixes:
- Fix a page leak in nfs_destroy_unlinked_subrequests()
- Fix use-after-free issues in nfs_pageio_add_request()
- Fix new mount code constant_table array definitions
- finish_automount() requires us to hold 2 refs to the mount record
Features:
- Improve the accuracy of telldir/seekdir by using 64-bit cookies
when possible.
- Allow one RDMA active connection and several zombie connections to
prevent blocking if the remote server is unresponsive.
- Limit the size of the NFS access cache by default
- Reduce the number of references to credentials that are taken by
NFS
- pNFS files and flexfiles drivers now support per-layout segment
COMMIT lists.
- Enable partial-file layout segments in the pNFS/flexfiles driver.
- Add support for CB_RECALL_ANY to the pNFS flexfiles layout type
- pNFS/flexfiles Report NFS4ERR_DELAY and NFS4ERR_GRACE errors from
the DS using the layouterror mechanism.
Bugfixes and cleanups:
- SUNRPC: Fix krb5p regressions
- Don't specify NFS version in "UDP not supported" error
- nfsroot: set tcp as the default transport protocol
- pnfs: Return valid stateids in nfs_layout_find_inode_by_stateid()
- alloc_nfs_open_context() must use the file cred when available
- Fix locking when dereferencing the delegation cred
- Fix memory leaks in O_DIRECT when nfs_get_lock_context() fails
- Various clean ups of the NFS O_DIRECT commit code
- Clean up RDMA connect/disconnect
- Replace zero-length arrays with C99-style flexible arrays"
* tag 'nfs-for-5.7-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (86 commits)
NFS: Clean up process of marking inode stale.
SUNRPC: Don't start a timer on an already queued rpc task
NFS/pnfs: Reference the layout cred in pnfs_prepare_layoutreturn()
NFS/pnfs: Fix dereference of layout cred in pnfs_layoutcommit_inode()
NFS: Beware when dereferencing the delegation cred
NFS: Add a module parameter to set nfs_mountpoint_expiry_timeout
NFS: finish_automount() requires us to hold 2 refs to the mount record
NFS: Fix a few constant_table array definitions
NFS: Try to join page groups before an O_DIRECT retransmission
NFS: Refactor nfs_lock_and_join_requests()
NFS: Reverse the submission order of requests in __nfs_pageio_add_request()
NFS: Clean up nfs_lock_and_join_requests()
NFS: Remove the redundant function nfs_pgio_has_mirroring()
NFS: Fix memory leaks in nfs_pageio_stop_mirroring()
NFS: Fix a request reference leak in nfs_direct_write_clear_reqs()
NFS: Fix use-after-free issues in nfs_pageio_add_request()
NFS: Fix races nfs_page_group_destroy() vs nfs_destroy_unlinked_subrequests()
NFS: Fix a page leak in nfs_destroy_unlinked_subrequests()
NFS: Remove unused FLUSH_SYNC support in nfs_initiate_pgio()
pNFS/flexfiles: Specify the layout segment range in LAYOUTGET
...
Pull networking fixes from David Miller:
1) Slave bond and team devices should not be assigned ipv6 link local
addresses, from Jarod Wilson.
2) Fix clock sink config on some at803x PHY devices, from Oleksij
Rempel.
3) Uninitialized stack space transmitted in slcan frames, fix from
Richard Palethorpe.
4) Guard HW VLAN ops properly in stmmac driver, from Jose Abreu.
5) "=" --> "|=" fix in aquantia driver, from Colin Ian King.
6) Fix TCP fallback in mptcp, from Florian Westphal. (accessing a plain
tcp_sk as if it were an mptcp socket).
7) Fix cavium driver in some configurations wrt. PTP, from Yue Haibing.
8) Make ipv6 and ipv4 consistent in the lower bound allowed for
neighbour entry retrans_time, from Hangbin Liu.
9) Don't use private workqueue in pegasus usb driver, from Petko
Manolov.
10) Fix integer overflow in mlxsw, from Colin Ian King.
11) Missing refcnt init in cls_tcindex, from Cong Wang.
12) One too many loop iterations when processing cmpri entries in ipv6
rpl code, from Alexander Aring.
13) Disable SG and TSO by default in r8169, from Heiner Kallweit.
14) NULL deref in macsec, from Davide Caratti.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (42 commits)
macsec: fix NULL dereference in macsec_upd_offload()
skbuff.h: Improve the checksum related comments
net: dsa: bcm_sf2: Ensure correct sub-node is parsed
qed: remove redundant assignment to variable 'rc'
wimax: remove some redundant assignments to variable result
mlxsw: spectrum_flower: Do not stop at FLOW_ACTION_VLAN_MANGLE
mlxsw: spectrum_flower: Do not stop at FLOW_ACTION_PRIORITY
r8169: change back SG and TSO to be disabled by default
net: dsa: bcm_sf2: Do not register slave MDIO bus with OF
ipv6: rpl: fix loop iteration
tun: Don't put_page() for all negative return values from XDP program
net: dsa: mt7530: fix null pointer dereferencing in port5 setup
mptcp: add some missing pr_fmt defines
net: phy: micrel: kszphy_resume(): add delay after genphy_resume() before accessing PHY registers
net_sched: fix a missing refcnt in tcindex_init()
net: stmmac: dwmac1000: fix out-of-bounds mac address reg setting
mlxsw: spectrum_trap: fix unintention integer overflow on left shift
pegasus: Remove pegasus' own workqueue
neigh: support smaller retrans_time settting
net: openvswitch: use hlist_for_each_entry_rcu instead of hlist_for_each_entry
...
Stefano originally proposed to introduce this flag, users hit EOPNOTSUPP
in new binaries with old kernels when defining a set with ranges in
a concatenation.
Fixes: f3a2181e16 ("netfilter: nf_tables: Support for sets with multiple ranged fields")
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
EINVAL should be used for malformed netlink messages. New userspace
utility and old kernels might easily result in EINVAL when exercising
new set features, which is misleading.
Fixes: 8aeff920dc ("netfilter: nf_tables: add stateful object reference to set elements")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
first_len is the remainder of the first page we're copying.
If this size is larger, then out of page boundary write will
otherwise happen.
Fixes: c05cd36458 ("xsk: add support to allow unaligned chunk placement")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1585813930-19712-1-git-send-email-lirongqing@baidu.com
This patch fix the loop iteration by not walking over the last
iteration. The cmpri compressing value exempt the last segment. As the
code shows the last iteration will be overwritten by cmpre value
handling which is for the last segment.
I think this doesn't end in any bufferoverflows because we work on worst
case temporary buffer sizes but it ends in not best compression settings
in some cases.
Fixes: 8610c7c6e3 ("net: ipv6: add support for rpl sr exthdr")
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix read with O_NONBLOCK to allow incomplete read and return immediately
- Rest is just cleanup (indent, unused field in struct, extra semicolon)
-----BEGIN PGP SIGNATURE-----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=wAe5
-----END PGP SIGNATURE-----
Merge tag '9p-for-5.7' of git://github.com/martinetd/linux
Pull 9p updates from Dominique Martinet:
"Not much new, but a few patches for this cycle:
- Fix read with O_NONBLOCK to allow incomplete read and return
immediately
- Rest is just cleanup (indent, unused field in struct, extra
semicolon)"
* tag '9p-for-5.7' of git://github.com/martinetd/linux:
net/9p: remove unused p9_req_t aux field
9p: read only once on O_NONBLOCK
9pnet: allow making incomplete read requests
9p: Remove unneeded semicolon
9p: Fix Kconfig indentation
ip_set_type_list is traversed using list_for_each_entry_rcu
outside an RCU read-side critical section but under the protection
of ip_set_type_mutex.
Hence, add corresponding lockdep expression to silence false-positive
warnings, and harden RCU lists.
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Android has long had an extension to IDLETIMER to send netlink
messages to userspace, see:
https://android.googlesource.com/kernel/common/+/refs/heads/android-mainline/include/uapi/linux/netfilter/xt_IDLETIMER.h#42
Note: this is idletimer target rev 1, there is no rev 0 in
the Android common kernel sources, see registration at:
https://android.googlesource.com/kernel/common/+/refs/heads/android-mainline/net/netfilter/xt_IDLETIMER.c#483
When we compare that to upstream's new idletimer target rev 1:
https://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next.git/tree/include/uapi/linux/netfilter/xt_IDLETIMER.h#n46
We immediately notice that these two rev 1 structs are the
same size and layout, and that while timer_type and send_nl_msg
are differently named and serve a different purpose, they're
at the same offset.
This makes them impossible to tell apart - and thus one cannot
know in a mixed Android/vanilla environment whether one means
timer_type or send_nl_msg.
Since this is iptables/netfilter uapi it introduces a problem
between iptables (vanilla vs Android) userspace and kernel
(vanilla vs Android) if the two don't match each other.
Additionally when at some point in the future Android picks up
5.7+ it's not at all clear how to resolve the resulting merge
conflict.
Furthermore, since upgrading the kernel on old Android phones
is pretty much impossible there does not seem to be an easy way
out of this predicament.
The only thing I've been able to come up with is some super
disgusting kernel version >= 5.7 check in the iptables binary
to flip between different struct layouts.
By adding a dummy field to the vanilla Linux kernel header file
we can force the two structs to be compatible with each other.
Long term I think I would like to deprecate send_nl_msg out of
Android entirely, but I haven't quite been able to figure out
exactly how we depend on it. It seems to be very similar to
sysfs notifications but with some extra info.
Currently it's actually always enabled whenever Android uses
the IDLETIMER target, so we could also probably entirely
remove it from the uapi in favour of just always enabling it,
but again we can't upgrade old kernels already in the field.
(Also note that this doesn't change the structure's size,
as it is simply fitting into the pre-existing padding, and
that since 5.7 hasn't been released yet, there's still time
to make this uapi visible change)
Cc: Manoj Basapathi <manojbm@codeaurora.org>
Cc: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Initialize set lookup matching element to NULL. Otherwise, the
NFT_LOOKUP_F_INV flag reverses the matching logic and it leads to
deference an uninitialized pointer to the matching element. Make sure
element data area and stateful expression are accessed if there is a
matching set element.
This patch undoes 24791b9aa1 ("netfilter: nft_set_bitmap: initialize set
element extension in lookups") which is not required anymore.
Fixes: 339706bc21 ("netfilter: nft_lookup: update element stateful expression")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Case a1. for overlap detection in __nft_rbtree_insert() is not a valid
one: start-after-start is not needed to detect any type of interval
overlap and it actually results in a false positive if, while
descending the tree, this is the only step we hit after starting from
the root.
This introduced a regression, as reported by Pablo, in Python tests
cases ip/ip.t and ip/numgen.t:
ip/ip.t: ERROR: line 124: add rule ip test-ip4 input ip hdrlength vmap { 0-4 : drop, 5 : accept, 6 : continue } counter: This rule should not have failed.
ip/numgen.t: ERROR: line 7: add rule ip test-ip4 pre dnat to numgen inc mod 10 map { 0-5 : 192.168.10.100, 6-9 : 192.168.20.200}: This rule should not have failed.
Drop case a1. and renumber others, so that they are a bit clearer. In
order for these diagrams to be readily understandable, a bigger rework
is probably needed, such as an ASCII art of the actual rbtree (instead
of a flattened version).
Shell script test sets/0044interval_overlap_0 should cover all
possible cases for false negatives, so I consider that test case still
sufficient after this change.
v2: Fix comments for cases a3. and b3.
Reported-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fixes: 7c84d41416 ("netfilter: nft_set_rbtree: Detect partial overlaps on insertion")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Eric Biggers