* Use optimized ATA version check from Sergei in ata_id_is_sata().
* ide_dev_is_sata() -> ata_id_is_sata()
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove (id[ATA_ID_FIELD_VALID] & 2) check from ide_dev_has_iordy()
(it is for validity of words 64-70, IORDY is in word 49).
* ide_dev_has_iordy() -> ata_id_has_iordy()
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out HDIO_{GET,SET}_NICE ioctl handling from
generic_ide_ioctl() to ide_{get,set}_nice_ioctl().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use drive->media and drive->scsi to check if ->dsc_overlap
can be set by HDIO_SET_NICE ioctl in generic_ide_ioctl().
* Remove unused ->supports_dsc_overlap field from ide_driver_t.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out the common code from check_prefetch()
and set_prefetch_mode() to __set_prefetch_mode().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add struct ide_devset, S_* flags, *DEVSET() & ide*_devset_*() macros.
* Add 'const struct ide_devset **settings' to ide_driver_t.
* Use 'const struct ide_devset **settings' in ide_drive_t instead of
'struct ide_settings_s *settings'. Then convert core code and device
drivers to use struct ide_devset and co.:
- device settings are no longer allocated dynamically for each device
but instead there is an unique struct ide_devset instance per setting
- device driver keeps the pointer to the table of pointers to its
settings in ide_driver_t.settings
- generic settings are kept in ide_generic_setting[]
- ide_proc_[un]register_driver(), ide_find_setting_by_name(),
ide_{read,write}_setting() and proc_ide_{read,write}_settings()
are updated accordingly
- ide*_add_settings() are removed
* Remove no longer used __ide_add_setting(), ide_add_setting(),
__ide_remove_setting() and auto_remove_settings().
* Remove no longer used TYPE_*, SETTING_*, ide_procset_t
and ide_settings_t.
* ->keep_settings, ->using_dma, ->unmask, ->noflush, ->dsc_overlap,
->nice1, ->addressing, ->wcache and ->nowerr ide_drive_t fields
can now be bitfield flags.
While at it:
* Rename ide_find_setting_by_name() to ide_find_setting().
* Rename write_wcache() to set_wcache().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After rework settings will be no longer created dynamically
for each device so we need to make some fixups first.
* Use set_[ksettings,unmaskirq]() as a set function for
["keepsettings","unmaskirq"] setting.
* Allow writes to ["io_32bit","unmaskirq"] settings also when
drive->no_[io_32bit,unmask] is set (this is checked later inside
set_[io_32bit,unmaskirq]() anywyay and keeps consistency with
the corresponding HDIO_SET_[32BIT,UNMASKINTR] ioctls).
* Use max possible multi sectors value (16) as an allowed max for
"multcount" setting. set_multcount() set function checks against
device's max possbile value anyway and it makes the proc setting
consistent with the corresponding HDIO_SET_MULTCOUNT ioctl.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Call ide_proc_register_driver() in ide*_setup() (just before
ide*_add_settings() call) instead of in ->probe method.
Despite being basically a preparation for /proc/ide/hd*/settings
rework this is a nice cleanup in itself.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Include <linux/ata.h> directly in <linux/ide.h>
instead of through <linux/hdreg.h>.
* Include <linux/hdreg.h> only when needed.
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use multi PIO by default when available and remove no longer
needed CONFIG_IDEDISK_MULTI_MODE (it should be safe nowadays,
despite to what help entry has been saying).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Change ide_get_paired_drive() to return NULL if peer device
is not present and update all users accordingly.
While at it:
* ide_get_paired_drive() -> ide_get_pair_dev()
* Use ide_get_pair_dev() in cs5530.c, sc1200.c and via82cxxx.c.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove needless drive->present checks from ->probe methods
(device model takes care of that).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
init_irq() is now called only during initial host registration
so these BUG_ON()-s are no loner needed (+ the last one was done
too late anyway).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_busy_sleep() take timeout value as a parameter
and also allow use of AltStatus Register if requested with
altstatus parameter. Update existing users accordingly.
* Convert ide_driveid_update() and actual_try_to_identify()
to use ide_busy_sleep().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix EXABYTENEST handling in probe_for_drive() (so drive->present
is checked for "nested" device) and cleanup enable_nest().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Friday 25 July 2008, Linus Torvalds wrote:
>
> On Fri, 25 Jul 2008, Ben Dooks wrote:
> >
> > personally, i would much prefer to see the loop being less evil
> > like:
> >
> > for (p = s; p < end; p += 2)
> > be16_to_cpus((u16 *)p);
>
> Well, in this case, the code actually depends on 'p' being back at the
> start of the buffer by the end of it all, so it would need some more
> changes than that.
>
> But yes, I applied David's patch, but I _also_ suspect that we would be
> better off without code that does horrid things like casts and assignments
> inside the function arguments.
>
> So it would be nice to re-code that loop to be more readable. But due to
> the reliance of 'p' being 's' after the loop, the minimal patch would be
> something like the appended.
>
> Bartlomiej - take this or not, I'm not going to commit it - I haven't
> tested it, nor do I even have any machines that would trigger it. So this
> is more a "maybe something like this" than anything else.
From: Linus Torvalds <torvalds@linux-foundation.org>
CC: Ben Dooks <ben-linux@fluff.org>
Cc: David Miller <davem@davemloft.net>
Cc: harvey.harrison@gmail.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ATA_CMD_* defines instead of WIN_* ones.
* Include <linux/ata.h> directly instead of through <linux/hdreg.h>.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ATA_CMD_* defines instead of WIN_* ones.
While at it:
* EXABYTE_ENABLE_NEXT -> ATA_EXABYTE_ENABLE_NEST
* SETFEATURES_{EN,DIS}_WCACHE -> SETFEATURES_WC_{ON,OFF}
* SETFEATURES_{EN,DIS}_AAM -> SETFEATURES_AAM_{ON,OFF}
* SMART_* -> ATA_SMART_*
* Remove stale comment from ide-proc.c.
Partially based on earlier work by Chris Wedgwood.
Acked-by: Chris Wedgwood <cw@f00f.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
idedisk_supports_hpa() -> ata_id_hpa_enabled().
The latter one also checks validity of words 82 & 85.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace open-coded check by ata_id_wcache_enabled()
(which also checks validity of word 85).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace open-coded checks by ata_id_current_chs_valid().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out HDIO_[OBSOLETE,GET]_IDENTITY ioctls handling
to ide_get_identity_ioctl().
* Use temporary buffer in ide_get_identity_ioctl() instead
of accessing drive->id directly.
* Add ide_id_to_hd_driveid() inline to convert raw id into
struct hd_driveid format (needed on big-endian).
* Use ide_id_to_hd_driveid() in ide_get_identity_ioctl(),
cleanup ide_fix_driveid() and switch ide to use use raw id.
* Remove no longer needed drive->driveid.
This leaves us with 3 users of struct hd_driveid in tree:
- arch/um/drivers/ubd_kern.c
- drivers/block/xsysace.c
- drivers/usb/storage/isd200.c
While at it:
* Use ata_id_u{32,64}() and ata_id_has_{dma,lba,iordy}() macros.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make drive->id an unnamed union so id can be accessed either by using
'u16 *id' or 'struct hd_driveid *driveid'. Then convert all existing
drive->id users accordingly (using 'u16 *id' when possible).
This is an intermediate step to make ide 'struct hd_driveid'-free.
While at it:
- Add missing KERN_CONTs in it821x.c.
- Use ATA_ID_WORDS and ATA_ID_*_LEN defines.
- Remove unnecessary checks for drive->id.
- s/drive_table/table/ in ide_in_drive_list().
- Cleanup ide_config_drive_speed() a bit.
- s/drive1/dev1/ & s/drive0/dev0/ in ide_undecoded_slave().
v2:
Fix typo in drivers/ide/ppc/pmac.c. (From Stephen Rothwell)
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove superfluous checks for drive->mult_req.
* No need to zero drive's fields.
* Move the common code out of #ifdef scope.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This condition is checked by both ide_disk_init_mult_count()
and set_multcount() so no need to do it again in ide_disk_special().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The format specifier for rq->sector didn't specify the proper size and
signedness. Borislav Petkov discovered that the signedness for
rq->nr_sectors and rq->current_nr_sectors also were incorrect.
Signed-off-by: Mark de Wever <koraq@xs4all.nl>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
[bart: remove trailing whitespace]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
selinux: Fix an uninitialized variable BUG/panic in selinux_secattr_to_sid()
selinux: use default proc sid on symlinks
file capabilities: uninline cap_safe_nice
Update selinux info in MAINTAINERS and Kconfig help text
SELinux: add gitignore file for mdp script
SELinux: add boundary support and thread context assignment
securityfs: do not depend on CONFIG_SECURITY
selinux: add support for installing a dummy policy (v2)
security: add/fix security kernel-doc
selinux: Unify for- and while-loop style
selinux: conditional expression type validation was off-by-one
smack: limit privilege by label
SELinux: Fix a potentially uninitialised variable in SELinux hooks
SELinux: trivial, remove unneeded local variable
SELinux: Trivial minor fixes that change C null character style
make selinux_write_opts() static
The 3215 console irq handler used to schedule a tasklet. However the
console irq handler also gets called from the infamous cio_tpi()
function. Which in turn does something like
local_bh_disable()
[call console irq handler]
_local_bh_enable()
_local_bh_enable() prevents execution of softirqs, which is intended
within cio_tpi(). However there might be a new softirq pending because
irq handler scheduled a tasklet.
In order to prevent this behaviour we just get rid of the tasklet.
It's not doing much anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 console drivers use the unblank callback of the console
structure to flush the console buffer. In case of a panic or a
reboot the CPU doing the callback can block on the console i/o.
The other CPUs in the system continue to work. For panic this is
not a good idea.
Replace the unblank callback with proper panic/reboot notifier.
These get called after all but one CPU have been stopped.
Signed-off-by: Holger Smolinski <Holger.Smolinski@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
EMC Symmetrix Subsystem Control I/O through CKD dasd requires a
specific parameter list sent to the array via a Perform Subsystem
Function CCW. The Symmetrix response is retrieved from the array
via a Read Subsystem Data CCW.
Signed-off-by: Nigel Hislop <hislop_nigel@emc.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The xpram driver uses a single block device queue for all of its
devices so far. With recent kernels removing xpram module fails to
clean up all sysfs files. The next time the xpram module is loaded
you'll get warnings:
WARNING: at fs/sysfs/dir.c:463 sysfs_add_one+0x5e/0x64()
sysfs: duplicate filename '35:0' can not be created
Modules linked in: xpram(+) [last unloaded: xpram]
Followed by the usual WARN_ON output, followed by an error message
from kobject_add_internal, followed by a badness in genhd. Allocating
a block queue per device fixes this.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In the unsolicited interupt handler fake IRBs from CIO have to be
ignored because there is nothing to do.
The function dump_sense should not be called if there is no sense
data available.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move cio's private simple udelay function to lib/delay.c and turn it
into something much more readable. So we have all implementations
at one place.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The DCSS block device driver is modified to add >2G DCSSs support and
allow a DCSS block device to map to a set of contiguous DCSSs. The
extmem code is also modified to use new Diagnose x'64' subcodes for
>2G DCSSs.
Signed-off-by: Hongjie Yang <hongjie@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for z10 HiperSockets multiwrite SBALs on output
queues. This is used on LPAR with EDDP enabled devices.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In commit e6bafba5b4, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way. In particular,
the result of !scsw_stctl(&request->irb.scsw) & SCSW_STCTL_STATUS_PEND is
always just !scsw_stctl(&request->irb.scsw).
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E; constant C; @@
(
!E & !C
|
- !E & C
+ !(E & C)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix incorrect in- and output constraints, remove volatile declaration
of inline assembly parameters and reformat constraint declarations to
be more consistent.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use dev_name() in the new qdio driver.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
No need to define a static device for the kvm_s390 root device,
just use s390_root_dev_register().
This is needed for the bus_id rework
Acked-by: Carsten Otte <cotte@de.ibm.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some further bus_id -> dev_name() conversions in s390 code.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert most s390 users setting bus_id to dev_set_name().
css and ccw busses are deferred since they need some special
treatment.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow users to remove blacklisted ccw devices by using the
/proc/cio_ignore interface:
echo purge > /proc/cio_ignore
will remove all devices which are offline and blacklisted.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use dedicated slow path work queue when unregistering a device due to
a user action. This ensures serialialization of other register/
unregister requests.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If an asynchronous HiperSockets queue runs full, no further packet
can be sent. In this case the next initiative to give transmitted
skbs back to the stack is triggered only by a 10-seconds qdio timer.
This timer has been introduced for low multicast traffic scenarios
to guarantee freeing of skbs in a limited amount of time. For high
HiperSocket multicast traffic scenarios progress checking on the
outbound queue should be enforced by tasklet rescheduling.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We were not reporting a status code back ath9k_hw_setpower() failed
during reset so lets correct this.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is fucking horribe crap code so nuke it. There I cursed too in a commit log.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On sparc32 debian etch, the cursor is not disabled
when leaving X windows. This patch disables the
cursor when leaving graphics mode just like the
ffb driver.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On sparc32 debian etch, the cursor is not disabled
when leaving X windows. This patch disables the
cursor when leaving graphics mode just like the
ffb driver.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (29 commits)
RDMA/nes: Fix slab corruption
IB/mlx4: Set RLKEY bit for kernel QPs
RDMA/nes: Correct error_module bit mask
RDMA/nes: Fix routed RDMA connections
RDMA/nes: Enhanced PFT management scheme
RDMA/nes: Handle AE bounds violation
RDMA/nes: Limit critical error interrupts
RDMA/nes: Stop spurious MAC interrupts
RDMA/nes: Correct tso_wqe_length
RDMA/nes: Fill in firmware version for ethtool
RDMA/nes: Use ethtool timer value
RDMA/nes: Correct MAX TSO frags value
RDMA/nes: Enable MC/UC after changing MTU
RDMA/nes: Free NIC TX buffers when destroying NIC QP
RDMA/nes: Fix MDC setting
RDMA/nes: Add wqm_quanta module option
RDMA/nes: Module parameter permissions
RDMA/cxgb3: Set active_mtu in ib_port_attr
RDMA/nes: Add support for 4-port 1G HP blade card
RDMA/nes: Make mini_cm_connect() static
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (37 commits)
[SCSI] zfcp: fix double dbf id usage
[SCSI] zfcp: wait on SCSI work to be finished before proceeding with init dev
[SCSI] zfcp: fix erp list usage without using locks
[SCSI] zfcp: prevent fc_remote_port_delete calls for unregistered rport
[SCSI] zfcp: fix deadlock caused by shared work queue tasks
[SCSI] zfcp: put threshold data in hba trace
[SCSI] zfcp: Simplify zfcp data structures
[SCSI] zfcp: Simplify get_adapter_by_busid
[SCSI] zfcp: remove all typedefs and replace them with standards
[SCSI] zfcp: attach and release SAN nameserver port on demand
[SCSI] zfcp: remove unused references, declarations and flags
[SCSI] zfcp: Update message with input from review
[SCSI] zfcp: add queue_full sysfs attribute
[SCSI] scsi_dh: suppress comparison warning
[SCSI] scsi_dh: add Dell product information into rdac device handler
[SCSI] qla2xxx: remove the unused SCSI_QLOGIC_FC_FIRMWARE option
[SCSI] qla2xxx: fix printk format warnings
[SCSI] qla2xxx: Update version number to 8.02.01-k8.
[SCSI] qla2xxx: Ignore payload reserved-bits during RSCN processing.
[SCSI] qla2xxx: Additional residual-count corrections during UNDERRUN handling.
...
* 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block: (132 commits)
doc/cdrom: Trvial documentation error, file not present
block_dev: fix kernel-doc in new functions
block: add some comments around the bio read-write flags
block: mark bio_split_pool static
block: Find bio sector offset given idx and offset
block: gendisk integrity wrapper
block: Switch blk_integrity_compare from bdev to gendisk
block: Fix double put in blk_integrity_unregister
block: Introduce integrity data ownership flag
block: revert part of d7533ad0e132f92e75c1b2eb7c26387b25a583c1
bio.h: Remove unused conditional code
block: remove end_{queued|dequeued}_request()
block: change elevator to use __blk_end_request()
gdrom: change to use __blk_end_request()
memstick: change to use __blk_end_request()
virtio_blk: change to use __blk_end_request()
blktrace: use BLKTRACE_BDEV_SIZE as the name size for setup structure
block: add lld busy state exporting interface
block: Fix blk_start_queueing() to not kick a stopped queue
include blktrace_api.h in headers_install
...
We already did that a long time ago for pnp_system_init, but
pnpacpi_init and pnpbios_init remained as subsys_initcalls, and get
linked into the kernel before the arch-specific routines that finalize
the PCI resources (pci_subsys_init).
This means that the PnP routines would either register their resources
before the PCI layer could, or would be unable to check whether a PCI
resource had already been registered. Both are problematic.
I wanted to do this before 2.6.27, but every time we change something
like this, something breaks. That said, _every_ single time we trust
some firmware (like PnP tables) more than we trust the hardware itself
(like PCI probing), the problems have been worse.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
libata-eh: clear UNIT ATTENTION after reset
ata_piix: add Hercules EC-900 mini-notebook to ich_laptop short cable list
libata: reorder ata_device to remove 8 bytes of padding on 64 bits
[libata] pata_bf54x: Add proper PM operation
pata_sil680: convert CONFIG_PPC_MERGE to CONFIG_PPC
libata: Implement disk shock protection support
[libata] Introduce ata_id_has_unload()
PATA: RPC now selects HAVE_PATA_PLATFORM for pata platform driver
ata_piix: drop merged SCR access and use slave_link instead
libata: implement slave_link
libata: misc updates to prepare for slave link
libata: reimplement link iterator
libata: make SCR access ops per-link
This patch allows the use of the hardware watchdog in the
Marvell Orion series of ARM SoCs.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
convert to use ioremap() and __raw_{read/write} friends.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
These are changes that have been sitting in linux-omap
and were never sent upstream.
Hopefully, it'll never happen again at least for this
driver.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a driver for the watchdog timer embedded into AT91SAM9X chips.
Signed-off-by: Renaud Cerrato <r.cerrato@til-technologies.fr>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Adapted the w83627hf_wdt.c driver to work with the w83697ug/uf chip,
found on MSI Fuzzy CX700 boards.
The method used is taken directly from the winbond datasheet and
surprisingly it differs slightly from all the other winbond watchdogs.
So far it has only been tested on the CX700 board that I have, but it
seems to work nicely.
Signed-off-by: Flemming Frandsen <ff@nrvissing.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Detect and report buggy drivers that destroy their request_queue.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Stefan Raspl <raspl@linux.vnet.ibm.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Publish dm_vcalloc in include/linux/device-mapper.h because this function is
used by targets.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Publish dm_table_unplug_all in include/linux/device-mapper.h because this
function is used by targets.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Publish dm_get_mapinfo in include/linux/device-mapper.h because this function
is used by targets.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Split struct dm_dev in two and publish the part that other targets need in
include/linux/device-mapper.h.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Don't wait between submitting crypt requests for a bio unless
we are short of memory.
There are two situations when we must split an encrypted bio:
1) there are no free pages;
2) the new bio would violate underlying device restrictions
(e.g. max hw segments).
In case (2) we do not need to wait.
Add output variable to crypt_alloc_buffer() to distinguish between
these cases.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move the initialisation of ctx->pending into one place, at the
start of crypt_convert().
Introduce crypt_finished to indicate whether or not the encryption
is finished, for use in a later patch.
No functional change.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The pending reference count must be incremented *before* the async work is
queued to another thread, not after. Otherwise there's a race if the
work completes and decrements the reference count before it gets incremented.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Make kcryptd_crypt_write_io_submit() responsible for decrementing
the pending count after an error.
Also fixes a bug in the async path that forgot to decrement it.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Make the caller reponsible for incrementing the pending count before calling
kcryptd_crypt_write_io_submit() in the non-async case to bring it into line
with the async case.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move kcryptd_crypt_write_convert_loop inside kcryptd_crypt_write_convert.
This change is needed for a later patch.
No functional change.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Factor out crypt io allocation code.
Later patches will call it from another place.
No functional change.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move io pending to one place.
No functional change, usefull to simplify debugging.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change uint32_t into chunk_t to remove 32-bit limitation on the
number of chunks on systems with 64-bit sector numbers.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move this logic to a function, because it will be reused later.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-raid1 is setting the 'DM_KCOPYD_IGNORE_ERROR' flag unconditionally
when assigning kcopyd work. kcopyd is responsible for copying an
assigned section of disk to one or more other disks. The
'DM_KCOPYD_IGNORE_ERROR' flag affects kcopyd in the following way:
When not set:
kcopyd will immediately stop the copy operation when an error is
encountered.
When set:
kcopyd will try to proceed regardless of errors and try to continue
copying any remaining amount.
Since dm-raid1 tracks regions of the address space that are (or
are not) in sync and it now has the ability to handle these
errors, we can safely enable this optimization. This optimization
is conditional on whether mirror error handling has been enabled.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch moves 'is_active' from struct dm_path to struct pgpath
as it does not need exporting.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch allows path errors from the multipath ctr function to
propagate up to userspace as errno values from the ioctl() call.
This is in response to
https://www.redhat.com/archives/dm-devel/2008-May/msg00000.html
and
https://bugzilla.redhat.com/show_bug.cgi?id=444421
The patch only lets through the errors that it needs to in order to
get the path errors from parse_path().
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Referencing cm_node after it is freed via rem_ref_cm_node() causes a
slab corruption. There is no need to set cm_node->cm_id to NULL in
mini_cm_close().
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix warnings caught by David Miller on sparc64
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to modulus the queue number in ->hard_start_xmit() since the
core is going to do that for you modulus ->real_num_tx_queues.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading transmit checksums only, the driver was not
correctly configuring the hardware to handle the case of a zero
checksum. For UDP the correct behavior is to leave it alone, but
for tcp the checksum must be changed from 0x0000 to 0xFFFF. The
hardware takes care of this case but only if it is told the
packet is tcp.
same patch as e1000e
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading transmit checksums only, the driver was not
correctly configuring the hardware to handle the case of a zero
checksum. For UDP the correct behavior is to leave it alone, but
for tcp the checksum must be changed from 0x0000 to 0xFFFF. The
hardware takes care of this case but only if it is told the
packet is tcp.
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before, the driver would not care about the return codes from pci_map_*
functions. This could be potentially dangerous if a mapping failed.
Now, we will check all pci_map_* calls. On the transmit side, we switch
to use the new function skb_dma_map(). On the receive side, we add
pci_dma_mapping_error().
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this new firmware, the driver no longer has to modify the
TCP/IP header fields when transmitting TSO packets.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check netif_running() state in most ethtool operations
and properly handle the !netif_running() state where the chip is
in an uninitailzed state or low power state that may not accept
any MMIO.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This logic is used in bnx2_close() and bnx2_suspend() and
so should be separated out into a separate function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to export the governors for use as the default governor,
because the default governor will be built-in anyway and we can access
the symbol directly.
This also fixes the following sparse warnings:
drivers/cpufreq/cpufreq_conservative.c:578:25: warning: symbol 'cpufreq_gov_conservative' was not declared. Should it be static?
drivers/cpufreq/cpufreq_ondemand.c:582:25: warning: symbol 'cpufreq_gov_ondemand' was not declared. Should it be static?
drivers/cpufreq/cpufreq_performance.c:39:25: warning: symbol 'cpufreq_gov_performance' was not declared. Should it be static?
drivers/cpufreq/cpufreq_powersave.c:38:25: warning: symbol 'cpufreq_gov_powersave' was not declared. Should it be static?
drivers/cpufreq/cpufreq_userspace.c:190:25: warning: symbol 'cpufreq_gov_userspace' was not declared. Should it be static?
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Use get_cpu_idle_time_us() to get micro-accounted idle information.
This enables ondemand to get more accurate idle and busy timings
than the jiffy based calculation. As a result, we can decrease
the ondemand safety gaurd band from 80-10 to 95-3.
Results in more aggressive power savings.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Use a parameter for down differential, instead of hardcoded 10%. Follow-on
patch changes the down-differential dynamically, based on whether
we are using idle micro-accounting or not.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Preparatory changes for doing idle micro-accounting in ondemand governor.
get_cpu_idle_time() gets extra parameter and returns idle time and also the
wall time that corresponds to the idle time measurement.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Change the load calculation algorithm in ondemand to work well with software
coordination of frequency across the dependent cpus.
Multiply individual CPU utilization with the average freq of that logical CPU
during the measurement interval (using getavg call). And find the max CPU
utilization number in terms of CPU freq. That number is then used to
get to the target freq for next sampling interval.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Add a cpu parameter to __cpufreq_driver_getavg(). This is needed for software
cpufreq coordination where policy->cpu may not be same as the CPU on which we
want to getavg frequency.
A follow-on patch will use this parameter to getavg freq from all cpus
in policy->cpus.
Change since last patch. Fix the offline/online and suspend/resume
oops reported by Youquan Song <youquan.song@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Venki Pallipadi made a similar change to the ondemand governor a while
back (in commit 28287033e1). It seems to
work just as well in the conservative governor, leading to fewer wakeups
as reported by powertop.
Signed-off-by: Ben Slusky <sluskyb@paranoiacs.org>
Signed-off-by: Dave Jones <davej@redhat.com>
After calling cpufreq_cpu_get, error handling code should call
cpufreq_cpu_put.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r@
expression x,E;
statement S;
position p1,p2,p3;
@@
(
if ((x = cpufreq_cpu_get@p1(...)) == NULL || ...) S
|
x = cpufreq_cpu_get@p1(...)
... when != x
if (x == NULL || ...) S
)
<...
if@p3 (...) { ... when != cpufreq_cpu_put(x)
when != if (x) { ... cpufreq_cpu_put(x); ...}
return@p2 ...;
}
...>
(
return x;
|
return 0;
|
x = E
|
E = x
|
cpufreq_cpu_put(x)
)
@exists@
position r.p1,r.p2,r.p3;
expression x;
int ret != 0;
statement S;
@@
* x = cpufreq_cpu_get@p1(...)
<...
* if@p3 (...)
S
...>
* return@p2 \(NULL\|ret\);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dave Jones <davej@redhat.com>
Add error handling for cpufreq_register_governor() error
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: cpufreq@lists.linux.org.uk
Signed-off-by: Dave Jones <davej@redhat.com>
1. arch/powerpc/platforms/pasemi/gpio_mdio.c also needs to be
converted over to mdiobus_{alloc,free}().
2. drivers/net/phy/fixed.c used to embed a struct mii_bus into its
struct fixed_mdio_bus and then use container_of() to go from the
former to the latter. Since mii bus structures are no longer
embedded, we need to do something like use the mii bus private
pointer to go from mii_bus to fixed_mdio_bus instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable driver checking of the DMI product name (when enabled) on
an Abit AT8 32X, instead of falling back to a manual probe. This
eliminates false negatives and eventually will help avoid
unnecessary bus probes on unsupported mainboards.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The table for the Abit AT8 32X was incorrectly missing an entry
for the sixth ("AUX3") fan. Add this entry, exporting the fan
reading to userspace.
Closes lm-sensors.org ticket #2339.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
On the Shuttle SN68PT, FAN_CTL2 is apparently not connected to a fan,
but to something else. One user has reported instant system power-off
when changing the PWM2 duty cycle, so we disable it.
I use the board name string as the trigger in case the same board is
ever used in other systems.
This closes lm-sensors ticket #2349:
pwmconfig causes a hard poweroff
http://www.lm-sensors.org/ticket/2349
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Creates a name file in the sysfs directory, that
is needed for the libsensors library to work.
Also rename fan1_pwm to pwm1 and scale its value as needed.
This fixes bug #11520:
http://bugzilla.kernel.org/show_bug.cgi?id=11520
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Since all bio_split calls refer the same single bio_split_pool, the bio_split
function can use bio_split_pool directly instead of the mempool_t parameter;
then the mempool_t parameter can be removed from bio_split param list, and
bio_split_pool is only referred in fs/bio.c file, can be marked static.
Signed-off-by: Denis ChengRq <crquan@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts gdrom to use __blk_end_request() directly
so that end_{queued|dequeued}_request() can be removed.
gd.transfer is '1' in error cases and '0' in non-error cases,
so gdrom hasn't been propagating any error code to the block layer.
We can just convert error cases to '-EIO'.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts memstick to use __blk_end_request() directly
so that end_{queued|dequeued}_request() can be removed.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts virtio_blk to use __blk_end_request() directly
so that end_{queued|dequeued}_request() can be removed.
Related 'uptodate' argument is converted to 'error'.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
SSD devices should give an RPM setting of 1 in word 217 of the ID
page. If we see such a device, tell the block layer about it.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The current floppy_struct allows floppies to number sectors starting
from 0 or 1. This patch allows arbitrary first-sector numbers - for
example, 0xC1 for Amstrad CPC disks.
This extends the existing 1-bit field (FD_ZEROBASED, bit 2 of stretch)
to 8 bits (FD_SECTMASK, bits 2 to 9).
Currently 0x00 denotes a first sector number of 1, and 0x01 denotes a
first sector number of 0. We extend this by interpreting FD_SECTMASK
as the first sector number with the LSB flipped.
Signed-off-by: Keith Wansbrough <keith@lochan.org>
Cc: Alain Knaff <alain@linux.lu>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Karel Zak <kzak@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix cciss SCSI rescan code to better notice device changes.
If you hot-unplug a tape drive, then hot-plug a different
tape drive into the same slot in a storage enclosure,
the cciss driver wouldn't notice anything had changed, as
it was only looking at the LUN address and device type.
Now it looks at the inquiry page 0x83 device identifier,
and vendor and model strings as well.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Until recently, the maximum number of xvd block devices you could attach
to a Xen domU was 16. This limitation turned out to be problematic for
some users, so it was expanded to handle a much larger number of disks.
However, this requires a couple of changes in the way that blkfront
scans for disks. This functionality is already present in the Xen
linux-2.6.18-xen.hg tree; the attached patch adds this functionality to
the mainline xen-blkfront implementation. I successfully tested it on a
2.6.25 tree, and build tested it on 2.6.27-rc3.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
blk_rq_unmap_user in sg_finish_rem_req can take care of all the cases.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sg_read_xfer was used to copy data to user space for READ
commands. blk_rq_unmap_user does the job so sg_read_xfer does nothing
useful.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sg_write_xfer was used to copy data from user space for WRITE
commands. blk_rq_map_user_iov and blk_rq_map_user do the job so
sg_write_xfer does nothing useful.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Calling blk_rq_map_user() at a single place is better than at
different two places. It makes the code more understandable.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
__sg_start_req() was used temporarily to call blk_get_request() during
converting sg to use the block layer.
Now sg always calls blk_get_request() so we can move blk_get_request()
to sg_start_req(). We don't need __sg_start_req anymore.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's not used for anything useful after the block layer conversion.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sg had lots of the own functions for the direct IO but now sg uses the
block layer functions for it. There are only five lines for the direct
IO. SG_ALLOW_DIO_CODE define was used to compile out the direct IO
code but we don't need the define. If someone wants to remove the
direct IO code, he can do easily without the define.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
old sg_rq_end_io() was used to wrap sg_cmd_done during converting sg
to use the block layer (in order to cover the difference
scsi_execute_async and blk_execute_rq_nowait). Now we don't need it so
let's remove it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Bartlomiej Zolnierkiewicz