Add support for Dual Data Rate MMC cards as defined in the 4.4
specification.
Signed-off-by: Hanumath Prasad <hanumath.prasad@stericsson.com>
Cc: linux-mmc@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Global symbols should use their subsystem name in a prefixed fashion.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Conversion from struct device to struct mmc_card is used more than in one
place. Due to this it's better to have public macro for such thing.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are some chips (like TI WL12xx series) that can be interfaced over
SDIO but don't support the SDIO specification, meaning that they are
missing CIA (Common I/O Area) with all it's registers. Current Linux SDIO
implementation relies on those registers to identify and configure the
card, so non-standard cards can not function and cause lots of warnings
from the core when it reads invalid data from non-existent registers.
After this patch, init_card() host callback can now set new quirk
MMC_QUIRK_NONSTD_SDIO, which means that SDIO core should not try to access
any standard SDIO registers and rely on init_card() to fill all SDIO
structures instead. As those cards are usually embedded chips, all the
required information can be obtained from machine board files by the host
driver when it's called through init_card() callback.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Kalle Valo <kvalo@adurom.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The eMMC spec 4.4 and 4.3 + additional feature chips has CSD structure
version 3 and version 3 have to check the CSD_STRUCTURE byte in the
EXT_CSD register.
Also fix EXT_CSD revision message.
[akpm@linux-foundation.org: fix comment, per Chris Ball]
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDIO cards expect byte transfers not to exceed the configured block
transfer size. Add a quirk to that effect.
Patches to make use of this quirk will be sent separately.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Normally writes to SDIO function 0 outside the vendor specific CCCR
registers are prohibited.
To support embedded devices that require writes to SDIO function 0 outside
this range (e.g. TI WL127x embedded sdio wifi device),
MMC_QUIRK_LENIENT_FN0 is introduced.
A card quirks field is added to `struct mmc_card' to support non-standard
devices (e.g. embedded sdio devices).
[akpm@linux-foundation.org: code in C, not cpp!]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to disconnect the pull-up resistor on CD/DAT[3] (pin 1)
of the card. This may be desired on certain setups of boards,
controllers and embedded sdio devices which do not need the card's
pull-up. As a result, card detection is disabled and power is saved.
[akpm@linux-foundation.org: simplify sdio_disable_cd() a bit]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the new MMC command SLEEP_AWAKE.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For each card successfully added to the bus, create a subdirectory under
the host's debugfs root with information about the card.
At the moment, only a single file is added to the card directory for
all cards: "state". It reflects the "state" field in struct mmc_card,
indicating whether the card is present, readonly, etc.
For MMC and SD cards (not SDIO), another file is added: "status".
Reading this file will ask the card about its current status and
return it. This can be useful if the card just refuses to respond to
any commands, which might indicate that the card state is not what the
MMC core thinks it is (due to a missing stop command, for example.)
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add a more clean separation between global, common CIS information
and the function specific one as we need the common information in
places where no specific function is specified.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The classic MMC bus was defined as multi card bus
system, which is reflected in the design in the MMC
layer.
When SD showed up, the bus topology was abandoned
and a star topology (one card per host) was mandated.
MMC version 4 has followed this, officially deprecating
the bus topology.
As we do not have any known users of the bus
topology we can remove support for it. This will
simplify the code and rectify some incorrect
assumptions in the newer additions.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support for MMC 4.2 sector based cards. This tweaks the init a
bit and reads a new field out of the EXT_CSD.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Thanks to the generous donation of an SDHC card by John Gilmore, and
the surprisingly enlightened decision by the SD Card Association to
publish useful specs, I've been able to bash out support for SDHC. The
changes are not too profound:
i) Add a card flag indicating the card uses block level addressing and
check it in the block driver. As we never took advantage of byte-level
addressing, this simply involves skipping the block -> byte
translation when sending commands.
ii) The layout of the CSD is changed - a set of fields are discarded
to make space for a larger C_SIZE. We did not reference any of the
discarded fields except those related to the C_SIZE.
iii) Read and write timeouts are fixed values and not calculated from
CSD values.
iv) Before invoking SEND_APP_OP_COND, we must invoke the new
SEND_IF_COND to inform the card we support SDHC.
Signed-off-by: Philipl Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Modern SD cards support a clock speed of 50 MHz. Make sure we test for
this capability and do the song and dance required to activate it.
Activating high speed support actually modifies the TRAN_SPEED field
of the CSD. But as the spec says that the cards must report 50 MHz,
we might as well skip re-reading the CSD.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This adds support for the high-speed modes defined by mmc v4
(assuming the host controller is up to it). On a TI sdhci controller,
it improves read speed from 1.3MBps to 2.3MBps. The TI controller can
only go up to 24MHz, but everything helps. Another person has taken
this basic patch and used it on a Nokia 770 to get a bigger boost
because that controller can run at 48MHZ.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The CSD contains a "read2write factor" which determines the multiplier to
be applied to the read timeout to obtain the write timeout. We were
ignoring this parameter, resulting in the possibility for writes being
timed out too early.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Select a block size for IO based on the read and write block size
combinations, and whether the card supports partial block reads
and/or partial block writes.
If we are able to satisfy block reads but not block writes, mark
the device read only.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Read the SD specific SCR register from the card.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the read-only switch on SD cards which must be enforced by the
host.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the Secure Digital protocol in the MMC layer.
A summary of the legal issues surrounding SD cards, as understood by yours
truly:
Members of the Secure Digital Association, hereafter SDA, are required to sign
a NDA[1] before given access to any specifications. It has been speculated
that including an SD implementation would forbid these members to redistribute
Linux. This is the basic problem with SD support so it is unclear if it even
is a problem since it has no effect on those of us that aren't members.
The SDA doesn't seem to enforce these rules though since the patches included
here are based on documentation made public by some of the members. The most
complete specs[2] are actually released by Sandisk, one of the founding
companies of the SDA.
Because of this the NDA is considered a non-issue by most involved in the
discussions concerning these patches. It might be that the SDA is only
interested in protecting the so called "secure" bits of SD, which so far
hasn't been found in any public spec. (The card is split into two sections,
one "normal" and one "secure" which has an access scheme similar to TPM:s).
(As a side note, Microsoft is working to make things easier for us since they
want to be able to include the source code for a SD driver in one of their
development kits. HP is making sure that the new NDA will allow a Linux
implementation. So far only the SDIO specs have been opened up[3]. More will
hopefully follow.)
[1] http://www.sdcard.org/membership/images/ippolicy.pdf
[2] http://www.sandisk.com/pdf/oem/ProdManualSDCardv1.9.pdf
[3] http://www.sdcard.org/sdio/Simplified%20SDIO%20Card%20Specification.pdf
This patch contains the central parts of the SD support. If no MMC cards are
found on a bus then the MMC layer proceeds looking for SD cards. Helper
functions are extended to handle the special needs of SD cards.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Hanumath Prasad