Remove BUG_ON(), which is frowned upon and not needed here.
Restructure to remove some excessive complexity.
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Rename variables to better reflect what their purpose is. As a side
effect, this reduces the need for some of the comments previously
removed in this series.
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Remove "__of_" prefix from local function names. The pattern of
a leading "__" is used in drivers/of/ to signify a function that
must be called with a lock held. These functions do not fit
that pattern.
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Some function names are misleading or do not provide a good
sense of what they do. Rename the functions to ne more
informative.
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert comparisons to zero or NULL to logical expressions. A
small number of such comparisons remain where they provide more
clarity of the numeric nature of a variable.
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Remove extra debug and error printks. A single pr_err() will
be added at the end of this series to replace many of these
error messages.
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Remove comments that report what is obvious from the code.
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
On arm64 NUMA kernels we can pass "numa=off" on the command line to
disable NUMA. A side effect of this is that kmalloc_node() calls to
non-zero nodes will crash the system with an OOPS:
[ 0.000000] ITS@0x0000901000020000: allocated 2097152 Devices @10002000000 (flat, esz 8, psz 64K, shr 1)
[ 0.000000] Unable to handle kernel NULL pointer dereference at virtual address 00001680
[ 0.000000] pgd = fffffc0009470000
[ 0.000000] [00001680] *pgd=0000010ffff90003, *pud=0000010ffff90003, *pmd=0000010ffff90003, *pte=0000000000000000
[ 0.000000] Internal error: Oops: 96000006 [#1] SMP
.
.
.
[ 0.000000] [<fffffc00081c8950>] __alloc_pages_nodemask+0xa4/0xe68
[ 0.000000] [<fffffc000821fa70>] new_slab+0xd0/0x564
[ 0.000000] [<fffffc0008221e24>] ___slab_alloc+0x2e4/0x514
[ 0.000000] [<fffffc0008239498>] __slab_alloc+0x48/0x58
[ 0.000000] [<fffffc0008222c20>] __kmalloc_node+0xd0/0x2dc
[ 0.000000] [<fffffc0008115374>] __irq_domain_add+0x7c/0x164
[ 0.000000] [<fffffc0008b461dc>] its_probe+0x784/0x81c
[ 0.000000] [<fffffc0008b462bc>] its_init+0x48/0x1b0
[ 0.000000] [<fffffc0008b4543c>] gic_init_bases+0x228/0x360
[ 0.000000] [<fffffc0008b456bc>] gic_of_init+0x148/0x1cc
[ 0.000000] [<fffffc0008b5aec8>] of_irq_init+0x184/0x298
[ 0.000000] [<fffffc0008b43f9c>] irqchip_init+0x14/0x38
[ 0.000000] [<fffffc0008b12d60>] init_IRQ+0xc/0x30
[ 0.000000] [<fffffc0008b10a3c>] start_kernel+0x240/0x3b8
[ 0.000000] [<fffffc0008b101c4>] __primary_switched+0x30/0x6c
[ 0.000000] Code: 912ec2a0 b9403809 0a0902fb 37b007db (f9400300)
.
.
.
This is caused by code like this in kernel/irq/irqdomain.c
domain = kzalloc_node(sizeof(*domain) + (sizeof(unsigned int) * size),
GFP_KERNEL, of_node_to_nid(of_node));
When NUMA is disabled, the concept of a node is really undefined, so
of_node_to_nid() should unconditionally return NUMA_NO_NODE.
Fix by returning NUMA_NO_NODE when the nid is not in the set of
possible nodes.
Reported-by: Gilbert Netzer <noname@pdc.kth.se>
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Rob Herring <robh@kernel.org>
This new helper function could be used by host drivers to get the limitaion
of max link speed provided by DT. If the property isn't assigned or is
invalid, it will return -EINVAL to the caller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
This reverts commit 05fd007e46 ("console: don't prefer first
registered if DT specifies stdout-path").
The reverted commit changes existing behavior on which many ARM boards
rely. Many ARM small-board-computers, like e.g. the Raspberry Pi have
both a video output and a serial console. Depending on whether the user
is using the device as a more regular computer; or as a headless device
we need to have the console on either one or the other.
Many users rely on the kernel behavior of the console being present on
both outputs, before the reverted commit the console setup with no
console= kernel arguments on an ARM board which sets stdout-path in dt
would look like this:
[root@localhost ~]# cat /proc/consoles
ttyS0 -W- (EC p a) 4:64
tty0 -WU (E p ) 4:1
Where as after the reverted commit, it looks like this:
[root@localhost ~]# cat /proc/consoles
ttyS0 -W- (EC p a) 4:64
This commit reverts commit 05fd007e46 ("console: don't prefer first
registered if DT specifies stdout-path") restoring the original
behavior.
Fixes: 05fd007e46 ("console: don't prefer first registered if DT specifies stdout-path")
Link: http://lkml.kernel.org/r/20161104121135.4780-2-hdegoede@redhat.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch add of overlay notifications.
When DT overlays are being added, some drivers/subsystems
need to see device tree overlays before the changes go into
the live tree.
This is distinct from reconfig notifiers that are
post-apply or post-remove and which issue very granular
notifications without providing access to the context
of a whole overlay.
The following 4 notificatons are issued:
OF_OVERLAY_PRE_APPLY
OF_OVERLAY_POST_APPLY
OF_OVERLAY_PRE_REMOVE
OF_OVERLAY_POST_REMOVE
In the case of pre-apply notification, if the notifier
returns error, the overlay will be rejected.
This patch exports two functions for registering/unregistering
notifications:
of_overlay_notifier_register(struct notifier_block *nb)
of_overlay_notifier_unregister(struct notifier_block *nb)
The of_mutex is held during these notifications. The
notification data includes pointers to the overlay target
and the overlay:
struct of_overlay_notify_data {
struct device_node *overlay;
struct device_node *target;
};
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The of_msi_configure routine is only accessible by the built-in
kernel drivers. Export this function so that modules can use it
too.
This function is useful for configuring MSI on child device tree
nodes on hierarchical objects.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull MIPS updates from Ralf Baechle:
"This is the main MIPS pull request for 4.9:
MIPS core arch code:
- traps: 64bit kernels should read CP0_EBase 64bit
- traps: Convert ebase to KSEG0
- c-r4k: Drop bc_wback_inv() from icache flush
- c-r4k: Split user/kernel flush_icache_range()
- cacheflush: Use __flush_icache_user_range()
- uprobes: Flush icache via kernel address
- KVM: Use __local_flush_icache_user_range()
- c-r4k: Fix flush_icache_range() for EVA
- Fix -mabi=64 build of vdso.lds
- VDSO: Drop duplicated -I*/-E* aflags
- tracing: move insn_has_delay_slot to a shared header
- tracing: disable uprobe/kprobe on compact branch instructions
- ptrace: Fix regs_return_value for kernel context
- Squash lines for simple wrapper functions
- Move identification of VP(E) into proc.c from smp-mt.c
- Add definitions of SYNC barrierstype values
- traps: Ensure full EBase is written
- tlb-r4k: If there are wired entries, don't use TLBINVF
- Sanitise coherentio semantics
- dma-default: Don't check hw_coherentio if device is non-coherent
- Support per-device DMA coherence
- Adjust MIPS64 CAC_BASE to reflect Config.K0
- Support generating Flattened Image Trees (.itb)
- generic: Introduce generic DT-based board support
- generic: Convert SEAD-3 to a generic board
- Enable hardened usercopy
- Don't specify STACKPROTECTOR in defconfigs
Octeon:
- Delete dead code and files across the platform.
- Change to use all memory into use by default.
- Rename upper case variables in setup code to lowercase.
- Delete legacy hack for broken bootloaders.
- Leave maintaining the link state to the actual ethernet/PHY drivers.
- Add DTS for D-Link DSR-500N.
- Fix PCI interrupt routing on D-Link DSR-500N.
Pistachio:
- Remove ANDROID_TIMED_OUTPUT from defconfig
TX39xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
TX49xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
txx9wdt:
- Add missing clock (un)prepare calls for CCF
BMIPS:
- Add PW, GPIO SDHCI and NAND device node names
- Support APPENDED_DTB
- Add missing bcm97435svmb to DT_NONE
- Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
- Add DT examples for BCM63268, BCM3368 and BCM6362
- Add support for BCM3368 and BCM6362
PCI
- Reduce stack frame usage
- Use struct list_head lists
- Support for CONFIG_PCI_DOMAINS_GENERIC
- Make pcibios_set_cache_line_size an initcall
- Inline pcibios_assign_all_busses
- Split pci.c into pci.c & pci-legacy.c
- Introduce CONFIG_PCI_DRIVERS_LEGACY
- Support generic drivers
CPC
- Convert bare 'unsigned' to 'unsigned int'
- Avoid lock when MIPS CM >= 3 is present
GIC:
- Delete unused file smp-gic.c
mt7620:
- Delete unnecessary assignment for the field "owner" from PCI
BCM63xx:
- Let clk_disable() return immediately if clk is NULL
pm-cps:
- Change FSB workaround to CPU blacklist
- Update comments on barrier instructions
- Use MIPS standard lightweight ordering barrier
- Use MIPS standard completion barrier
- Remove selection of sync types
- Add MIPSr6 CPU support
- Support CM3 changes to Coherence Enable Register
SMP:
- Wrap call to mips_cpc_lock_other in mips_cm_lock_other
- Introduce mechanism for freeing and allocating IPIs
cpuidle:
- cpuidle-cps: Enable use with MIPSr6 CPUs.
SEAD3:
- Rewrite to use DT and generic kernel feature.
USB:
- host: ehci-sead3: Remove SEAD-3 EHCI code
FBDEV:
- cobalt_lcdfb: Drop SEAD3 support
dt-bindings:
- Document a binding for simple ASCII LCDs
auxdisplay:
- img-ascii-lcd: driver for simple ASCII LCD displays
irqchip i8259:
- i8259: Add domain before mapping parent irq
- i8259: Allow platforms to override poll function
- i8259: Remove unused i8259A_irq_pending
Malta:
- Rewrite to use DT
of/platform:
- Probe "isa" busses by default
CM:
- Print CM error reports upon bus errors
Module:
- Migrate exception table users off module.h and onto extable.h
- Make various drivers explicitly non-modular:
- Audit and remove any unnecessary uses of module.h
mailmap:
- Canonicalize to Qais' current email address.
Documentation:
- MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
Loongson1C:
- Add CPU support for Loongson1C
- Add board support
- Add defconfig
- Add RTC support for Loongson1C board
All this except one Documentation fix has sat in linux-next and has
survived Imagination's automated build test system"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
MIPS: ptrace: Fix regs_return_value for kernel context
MIPS: VDSO: Drop duplicated -I*/-E* aflags
MIPS: Fix -mabi=64 build of vdso.lds
MIPS: Enable hardened usercopy
MIPS: generic: Convert SEAD-3 to a generic board
MIPS: generic: Introduce generic DT-based board support
MIPS: Support generating Flattened Image Trees (.itb)
MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
MIPS: Print CM error reports upon bus errors
MIPS: Support per-device DMA coherence
MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
MIPS: Sanitise coherentio semantics
MIPS: PCI: Support generic drivers
MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
MIPS: PCI: Inline pcibios_assign_all_busses
MIPS: PCI: Make pcibios_set_cache_line_size an initcall
MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
MIPS: PCI: Use struct list_head lists
...
Including:
* Support for interrupt virtualization in the AMD IOMMU driver.
These patches were shared with the KVM tree and are already
merged through that tree.
* Generic DT-binding support for the ARM-SMMU driver. With this
the driver now makes use of the generic DMA-API code. This
also required some changes outside of the IOMMU code, but
these are acked by the respective maintainers.
* More cleanups and fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1hFE
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- support for interrupt virtualization in the AMD IOMMU driver. These
patches were shared with the KVM tree and are already merged through
that tree.
- generic DT-binding support for the ARM-SMMU driver. With this the
driver now makes use of the generic DMA-API code. This also required
some changes outside of the IOMMU code, but these are acked by the
respective maintainers.
- more cleanups and fixes all over the place.
* tag 'iommu-updates-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (40 commits)
iommu/amd: No need to wait iommu completion if no dte irq entry change
iommu/amd: Free domain id when free a domain of struct dma_ops_domain
iommu/amd: Use standard bitmap operation to set bitmap
iommu/amd: Clean up the cmpxchg64 invocation
iommu/io-pgtable-arm: Check for v7s-incapable systems
iommu/dma: Avoid PCI host bridge windows
iommu/dma: Add support for mapping MSIs
iommu/arm-smmu: Set domain geometry
iommu/arm-smmu: Wire up generic configuration support
Docs: dt: document ARM SMMU generic binding usage
iommu/arm-smmu: Convert to iommu_fwspec
iommu/arm-smmu: Intelligent SMR allocation
iommu/arm-smmu: Add a stream map entry iterator
iommu/arm-smmu: Streamline SMMU data lookups
iommu/arm-smmu: Refactor mmu-masters handling
iommu/arm-smmu: Keep track of S2CR state
iommu/arm-smmu: Consolidate stream map entry state
iommu/arm-smmu: Handle stream IDs more dynamically
iommu/arm-smmu: Set PRIVCFG in stage 1 STEs
iommu/arm-smmu: Support non-PCI devices with SMMUv3
...
NAND:
* Add the infrastructure to automate NAND timings configuration
* Provide a generic DT property to maximize ECC strength
* Some refactoring in the core bad block table handling, to help with
improving some of the logic in error cases.
* Minor cleanups and fixes
MTD:
* Add APIs for handling page pairing; this is necessary for reliably
supporting MLC and TLC NAND flash, where paired-page disturbance affects
reliability. Upper layers (e.g., UBI) should make use of these in the near
future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/PuY
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20161008' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"I've not been very active this cycle, so these are mostly from Boris,
for the NAND flash subsystem.
NAND:
- Add the infrastructure to automate NAND timings configuration
- Provide a generic DT property to maximize ECC strength
- Some refactoring in the core bad block table handling, to help with
improving some of the logic in error cases.
- Minor cleanups and fixes
MTD:
- Add APIs for handling page pairing; this is necessary for reliably
supporting MLC and TLC NAND flash, where paired-page disturbance
affects reliability. Upper layers (e.g., UBI) should make use of
these in the near future"
* tag 'for-linus-20161008' of git://git.infradead.org/linux-mtd: (35 commits)
mtd: nand: fix trivial spelling error
mtdpart: Propagate _get/put_device()
mtd: nand: Provide nand_cleanup() function to free NAND related resources
mtd: Kill the OF_MTD Kconfig option
mtd: nand: mxc: Test CONFIG_OF instead of CONFIG_OF_MTD
mtd: nand: Fix nand_command_lp() for 8bits opcodes
mtd: nand: sunxi: Support ECC maximization
mtd: nand: Support maximizing ECC when using software BCH
mtd: nand: Add an option to maximize the ECC strength
mtd: nand: mxc: Add timing setup for v2 controllers
mtd: nand: mxc: implement onfi get/set features
mtd: nand: sunxi: switch from manual to automated timing config
mtd: nand: automate NAND timings selection
mtd: nand: Expose data interface for ONFI mode 0
mtd: nand: Add function to convert ONFI mode to data_interface
mtd: nand: convert ONFI mode into data interface
mtd: nand: Introduce nand_data_interface
mtd: nand: Create a NAND reset function
mtd: nand: remove unnecessary 'extern' from function declarations
MAINTAINERS: Add maintainer entry for Ingenic JZ4780 NAND driver
...
If a device tree specifies a preferred device for kernel console output
via the stdout-path or linux,stdout-path chosen node properties or the
stdout alias then the kernel ought to honor it & output the kernel
console to that device. As it stands, this isn't the case. Whilst we
parse the stdout-path properties & set an of_stdout variable from
of_alias_scan(), and use that from of_console_check() to determine
whether to add a console device as a preferred console whilst
registering it, we also prefer the first registered console if no other
has been selected at the time of its registration.
This means that if a console other than the one the device tree selects
via stdout-path is registered first, we will switch to using it & when
the stdout-path console is later registered the call to
add_preferred_console() via of_console_check() is too late to do
anything useful. In practice this seems to mean that we switch to the
dummy console device fairly early & see no further console output:
Console: colour dummy device 80x25
console [tty0] enabled
bootconsole [ns16550a0] disabled
Fix this by not automatically preferring the first registered console if
one is specified by the device tree. This allows consoles to be
registered but not enabled, and once the driver for the console selected
by stdout-path calls of_console_check() the driver will be added to the
list of preferred consoles before any other console has been enabled.
When that console is then registered via register_console() it will be
enabled as expected.
Link: http://lkml.kernel.org/r/20160809151937.26118-1-paul.burton@imgtec.com
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ivan Delalande <colona@arista.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Jan Kara <jack@suse.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Joe Perches <joe@perches.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 44a7185c2a ("of/platform: Add common method to populate
default bus") platforms calling of_platform_bus_probe from an initcall
is either a rather unsafe race with of_platform_default_populate_init or
a no-op. The MIPS Malta board needs to probe devices under an ISA bus,
which we do support in the of_busses array but until now haven't
included in of_default_bus_match_table.
Add an "isa" entry to of_default_bus_match_table such that we can just
accept use of of_platform_default_populate_init & remove the
Malta-specific match table in a later patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14275/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here is the big TTY and Serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by some
serial drivers, and they were all acked by the DMA maintainer. Also in
here is the long-suffering ACPI SPCR patchset, which was passed around
from maintainer to maintainer like a hot-potato. Seems I was the
sucker^Wlucky one. All of those patches have been acked by the various
subsystem maintainers as well.
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNjEPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspwIcAn2uN
qCD8xQJ0Cs61hD1nUzhNygG8AJ94I4zz/fPGpyh/CtJfLQwtUdLhNA==
=Rken
-----END PGP SIGNATURE-----
Merge tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial updates from Greg KH:
"Here is the big tty and serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by
some serial drivers, and they were all acked by the DMA maintainer.
Also in here is the long-suffering ACPI SPCR patchset, which was
passed around from maintainer to maintainer like a hot-potato. Seems I
was the sucker^Wlucky one. All of those patches have been acked by the
various subsystem maintainers as well.
All of this has been in linux-next with no reported issues"
* tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (111 commits)
Revert "serial: pl011: add console matching function"
MAINTAINERS: update entry for atmel_serial driver
serial: pl011: add console matching function
ARM64: ACPI: enable ACPI_SPCR_TABLE
ACPI: parse SPCR and enable matching console
of/serial: move earlycon early_param handling to serial
Revert "drivers/tty: Explicitly pass current to show_stack"
tty: amba-pl011: Don't complain on -EPROBE_DEFER when no irq
nios2: dts: 10m50: Add tx-threshold parameter
serial: 8250: Set Altera 16550 TX FIFO Threshold
serial: 8250: of: Load TX FIFO Threshold from DT
Documentation: dt: serial: Add TX FIFO threshold parameter
drivers/tty: Explicitly pass current to show_stack
serial: imx: Fix DCD reading
serial: stm32: mark symbols static where possible
serial: xuartps: Add some register initialisation to cdns_early_console_setup()
serial: xuartps: Removed unwanted checks while reading the error conditions
serial: xuartps: Rewrite the interrupt handling logic
serial: stm32: use mapbase instead of membase for DMA
tty/serial: atmel: fix fractional baud rate computation
...
We have multiple "earlycon" early_param handlers - merge the DT one into
the main earlycon one. It's a cleanup that also will be useful
to defer setting up DT console until ACPI/DT decision is made.
Rename the exported function to avoid clashing with the function from
arch/microblaze/kernel/prom.c
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d48f62b9a0 ("mtd: nand: move of_get_nand_xxx() helpers into
nand_base.c") removed the drivers/of/of_mtd.c file but did not remove
the associated OF_MTD Kconfig option.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The PCI msi-map code is already doing double-duty translating IDs and
retrieving MSI parents, which unsurprisingly is the same functionality
we need for the identically-formatted PCI iommu-map property. Drag the
core parsing routine up yet another layer into the general OF-PCI code,
and further generalise it for either kind of lookup in either flavour
of map property.
Acked-by: Rob Herring <robh+dt@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Whilst we're some of the way towards a universal firmware property
interface, drivers which deal with both OF and ACPI probing end up
having to do things like this:
dev->of_node ? &dev->of_node->fwnode : dev->fwnode
This seems unnecessary, when the OF code could instead simply fill in
the device's fwnode when binding the of_node, and let the drivers use
dev->fwnode either way. Let's give it a go and see what falls out.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a new set of array reading functions that take a minimum and
maximum size limit and will fail if the property size is not within
the size limits. This makes it more convenient for drivers that
use variable-size DT arrays which must be bounded at both ends -
data must be at least N entries but must not overflow the array
it is being copied into. It is also more efficient than making this
functionality out of existing public functions and avoids duplication.
The existing array functions have been left in the API, since there
are a very large number of clients of those functions and their
existing functionality is still useful. This avoids turning a small
API improvement into a major kernel rework.
The old functions have been turned into mininmal static inlines calling
the new functions. The old functions had no upper limit on the actual
size of the dts entry, to preserve this functionality rather than keeping
two near-identical implementations, if the new function is called with
max=0 there is no limit on the size of the dts entry but only the min
number of elements are read.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Rob Herring <robh@kernel.org>
In preparation for adding variable-length array reads, change
of_find_property_value_of_size so that it takes an optional
maximum length. If the maximum is passed as 0, the behaviour is
unchanged and it will return a property if it's >= the requested
minimum length. If maximum is non-zero it will only return a
property whose length is min <= l <= max.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Use pr_fmt to prefix kernel output.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Use of_get_next_parent() instead of open-code.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This warning has been printed in of_numa_parse_cpu_nodes before.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If the numa-id which was configured in memory@ devicetree node is greater
than MAX_NUMNODES, we should report a warning. We have done this for cpus
and distance-map dt nodes, this patch help them to be consistent.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
For a normal memory@ devicetree node, its reg property can contains more
memory blocks.
Because we don't known how many memory blocks maybe contained, so we try
from index=0, increase 1 until error returned(the end).
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This information will be printed in the subfunction numa_add_memblk.
They are not the same, but very similar.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The called of_graph_get_next_endpoint() already decrements the refcount
of the prev node, so it is wrong to do it again in the calling function.
Use the for_each_endpoint_of_node() helper to interate through the
endpoint OF nodes, which already does the right thing and simplifies
the code a bit.
Fixes: 8ccd0d0ca0
(of: add helper for getting endpoint node of specific identifiers)
Cc: stable@vger.kernel.org
Reported-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
With the commit 44a7185c2a ("of/platform: Add common method to
populate default bus"), a default function is introduced to populate
the default bus and this function is invoked at the arch_initcall_sync
level. But a lot of ppc boards use machine_device_initcall() to
populate the default bus. This means that the default populate function
has higher priority and would override the arch specific population of
the bus. The side effect is that some arch specific bus are not probed,
then cause various malfunction due to the miss of some devices. Since
it is very possible to introduce bugs if we simply change the initcall
level for all these boards(about 30+). This just disable this default
function for all the ppc boards.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
That way the init callback may clear the flag again, in case of drivers
split between early irq chip and a normal platform driver.
Fixes: 15cc2ed6dc ("of/irq: Mark initialised interrupt controllers as populated")
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
@mynodes is set to NULL when __unflatten_device_tree() is called
to unflatten device sub-tree in PCI hot add scenario on PowerPC
PowerNV platform. Marking @mynodes detached unconditionally causes
kernel crash as below backtrace shows:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc000000000b26f64
cpu 0x0: Vector: 300 (Data Access) at [c000003fcc7cf740]
pc: c000000000b26f64: __unflatten_device_tree+0xf4/0x190
lr: c000000000b26f40: __unflatten_device_tree+0xd0/0x190
sp: c000003fcc7cf9c0
msr: 900000000280b033
dar: 0
dsisr: 40000000
current = 0xc000003fcc281680
paca = 0xc00000000ff00000 softe: 0 irq_happened: 0x01
pid = 2724, comm = sh
Linux version 4.7.0-gavin-07754-g92a6836 (gwshan@gwshan) (gcc version \
4.9.3 (Buildroot 2016.02-rc2-00093-g5ea3bce) ) #539 SMP Mon Aug 1 \
12:40:29 AEST 2016
enter ? for help
[c000003fcc7cfa50] c000000000b27060 of_fdt_unflatten_tree+0x60/0x90
[c000003fcc7cfaa0] c0000000004c6288 pnv_php_set_slot_power_state+0x118/0x440
[c000003fcc7cfb80] c0000000004c6a10 pnv_php_enable+0xc0/0x170
[c000003fcc7cfbd0] c0000000004c4d80 power_write_file+0xa0/0x190
[c000003fcc7cfc50] c0000000004be93c pci_slot_attr_store+0x3c/0x60
[c000003fcc7cfc70] c0000000002d3fd4 sysfs_kf_write+0x94/0xc0
[c000003fcc7cfcb0] c0000000002d2c30 kernfs_fop_write+0x180/0x260
[c000003fcc7cfd00] c000000000230fe0 __vfs_write+0x40/0x190
[c000003fcc7cfd90] c000000000232278 vfs_write+0xc8/0x240
[c000003fcc7cfde0] c000000000233d90 SyS_write+0x60/0x110
[c000003fcc7cfe30] c000000000009524 system_call+0x38/0x108
This avoids the kernel crash by marking @mynodes detached only when
@mynodes is dereferencing valid device node in __unflatten_device_tree().
Fixes: 1d1bde550e ("of: fdt: mark unflattened tree as detached")
Reported-by: Meng Li <shlimeng@cn.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The of_node_put() function tests whether its argument is NULL
and then returns immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Instead of a ramoops-specific node, use a child node of /reserved-memory.
This requires that of_platform_device_create() be explicitly called
for the node, though, since "/reserved-memory" does not have its own
"compatible" property.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder. from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang
Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman,
Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Z5kM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
- Removal of most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to call
it if they have special needs.
- Use pr_fmt on all the DT core print statements.
- CoreSight binding doc improvements to block name descriptions.
- Add dt_to_config script which can parse dts files and list
corresponding kernel config options.
- Fix memory leak hit with a PowerMac DT.
- Correct a bunch of STMicro compatible strings to use the correct
vendor prefix.
- Fix DA9052 PMIC binding doc to match what is actually used in dts
files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wLMr
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
- ACPI support for guests on ARM platforms.
- Generic steal time support for arm and x86.
- Support cases where kernel cpu is not Xen VCPU number (e.g., if
in-guest kexec is used).
- Use the system workqueue instead of a custom workqueue in various
places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXmLlrAAoJEFxbo/MsZsTRvRQH/1wOMF8BmlbZfR7H3qwDfjst
ApNifCiZE08xDtWBlwUaBFAQxyflQS9BBiNZDVK0sysIdXeOdpWV7V0ZjRoLL+xr
czsaaGXDcmXxJxApoMDVuT7FeP6rEk6LVAYRoHpVjJjMZGW3BbX1vZaMW4DXl2WM
9YNaF2Lj+rpc1f8iG31nUxwkpmcXFog6ct4tu7HiyCFT3hDkHt/a4ghuBdQItCkd
vqBa1pTpcGtQBhSmWzlylN/PV2+NKcRd+kGiwd09/O/rNzogTMCTTWeHKAtMpPYb
Cu6oSqJtlK5o0vtr0qyLSWEGIoyjE2gE92s0wN3iCzFY1PldqdsxUO622nIj+6o=
=G6q3
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Features and fixes for 4.8-rc0:
- ACPI support for guests on ARM platforms.
- Generic steal time support for arm and x86.
- Support cases where kernel cpu is not Xen VCPU number (e.g., if
in-guest kexec is used).
- Use the system workqueue instead of a custom workqueue in various
places"
* tag 'for-linus-4.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (47 commits)
xen: add static initialization of steal_clock op to xen_time_ops
xen/pvhvm: run xen_vcpu_setup() for the boot CPU
xen/evtchn: use xen_vcpu_id mapping
xen/events: fifo: use xen_vcpu_id mapping
xen/events: use xen_vcpu_id mapping in events_base
x86/xen: use xen_vcpu_id mapping when pointing vcpu_info to shared_info
x86/xen: use xen_vcpu_id mapping for HYPERVISOR_vcpu_op
xen: introduce xen_vcpu_id mapping
x86/acpi: store ACPI ids from MADT for future usage
x86/xen: update cpuid.h from Xen-4.7
xen/evtchn: add IOCTL_EVTCHN_RESTRICT
xen-blkback: really don't leak mode property
xen-blkback: constify instance of "struct attribute_group"
xen-blkfront: prefer xenbus_scanf() over xenbus_gather()
xen-blkback: prefer xenbus_scanf() over xenbus_gather()
xen: support runqueue steal time on xen
arm/xen: add support for vm_assist hypercall
xen: update xen headers
xen-pciback: drop superfluous variables
xen-pciback: short-circuit read path used for merging write values
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mrOW
-----END PGP SIGNATURE-----
Merge tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new framework support for HDMI CEC and remote control support
- new encoding codec driver for Mediatek SoC
- new frontend driver: helene tuner
- added support for NetUp almost universal devices, with supports
DVB-C/S/S2/T/T2 and ISDB-T
- the mn88472 frontend driver got promoted from staging
- a new driver for RCar video input
- some soc_camera legacy drivers got removed: timb, omap1, mx2, mx3
- lots of driver cleanups, improvements and fixups
* tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (377 commits)
[media] cec: always check all_device_types and features
[media] cec: poll should check if there is room in the tx queue
[media] vivid: support monitor all mode
[media] cec: fix test for unconfigured adapter in main message loop
[media] cec: limit the size of the transmit queue
[media] cec: zero unused msg part after msg->len
[media] cec: don't set fh to NULL in CEC_TRANSMIT
[media] cec: clear all status fields before transmit and always fill in sequence
[media] cec: CEC_RECEIVE overwrote the timeout field
[media] cxd2841er: Reading SNR for DVB-C added
[media] cxd2841er: Reading BER and UCB for DVB-C added
[media] cxd2841er: fix switch-case for DVB-C
[media] cxd2841er: fix signal strength scale for ISDB-T
[media] cxd2841er: adjust the dB scale for DVB-C
[media] cxd2841er: provide signal strength for DVB-C
[media] cxd2841er: fix BER report via DVBv5 stats API
[media] mb86a20s: apply mask to val after checking for read failure
[media] airspy: fix error logic during device register
[media] s5p-cec/TODO: add TODO item
[media] cec/TODO: drop comment about sphinx documentation
...
This provides an equivalent of of_fdt_match() for non-flat trees.
This is more practical than matching an array of of_device_id structs
when converting a bunch of existing users of of_fdt_match().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The tree returned from of_fdt_unflatten_tree cannot be attached to the
live tree because it is not marked as detached so mark it as such. The
dt resolver checks the flag and refuses to process the tree otherwise.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Applying overlay fails silently in case of an error. Add error prints.
Most notably the lack of symbols in the live tree is not reported.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Clean-up all the DT printk functions to use common pr_fmt prefix.
Some print statements such as kmalloc errors were redundant, so just
drop those.
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Abstract a general interface "of_phy_get_and_connect"
for PHY connect. User will have no bother with getting
"phy-mode" and "phy-handle" any more.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXefulAAoJEHm+PkMAQRiG6nMH/2O1vcZeOtqmx2yCMUeXyKAT
wG88XflXzf3rM7C7TiObEYVf/bbLleJ7saDLEeic7ButD5gyYacIuzylVnrcqfBc
vinz4cOw5kvu9DrRkCKdOfiTAgwYtqQW+syJ8ZK4lPQuSxnPAs+F/FKSOpyUF5FN
Dngr520KjYKBEtn27W9UDPChFRwQoWAlaOC534eusaArCJtHGHHiuq5TEDn2EIo8
pUw2vwx5JiquSHOY34WLU7r+QoilovCQlUSsBQdLlPjfMB1QFtclPYa+5yEMjkT4
wusOUOfS/zK0rV6KnEdc/SkpiVX5C9WpFiWUOdEeJ5mZ+KijVkaOa9K1EDx8jSM=
=7Hwh
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rc6' into patchwork
Linux 4.7-rc6
* tag 'v4.7-rc6': (1245 commits)
Linux 4.7-rc6
ovl: warn instead of error if d_type is not supported
MIPS: Fix possible corruption of cache mode by mprotect.
locks: use file_inode()
usb: dwc3: st: Use explicit reset_control_get_exclusive() API
phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
phy: miphy28lp: Inform the reset framework that our reset line may be shared
namespace: update event counter when umounting a deleted dentry
9p: use file_dentry()
lockd: unregister notifier blocks if the service fails to come up completely
ACPI,PCI,IRQ: correct operator precedence
fuse: serialize dirops by default
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
powerpc: Initialise pci_io_base as early as possible
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
...
Sometimes it needs to check if there is a subnode of given node in FDT
by given name. Introduce this helper to get the subnode if it exists.
CC: Rob Herring <robh@kernel.org>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Julien Grall <julien.grall@arm.com>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling the fixed-phy functions when CONFIG_FIXED_PHY=m as a previous
change tried cannot work if the caller is in built-in code:
drivers/of/built-in.o: In function `of_phy_register_fixed_link':
of_reserved_mem.c:(.text+0x85e0): undefined reference to `fixed_phy_register'
Making of_mdio depend on 'FIXED_PHY || !FIXED_PHY' would solve this
dependency by enforcing that OF_MDIO itself becomes a loadable module
when FIXED_PHY=y, but that creates a different dependency as it
breaks any built-in ethernet driver that uses of_mdio.
Making FIXED_PHY a bool option also cannot work, since it depends on
PHYLIB, which again is tristate.
This version now uses 'select FIXED_PHY' to ensure that the fixed-phy
portion of of_mdio is not optional. The main downside of this is
a small increase in code size for cases that do not need fixed phy
support, but it should avoid all of the link-time problems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d1bd330a22 ("of_mdio: Enable fixed PHY support if driver is a module")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For interrupt controllers successfully initialised early via device-tree,
mark these interrupt controllers as populated so we don't unnecessarily
create a device and populate any platform data later on in the boot
sequence when we populate all the various platform devices.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Fix a memory leak resulting from memory allocation in safe_name().
This patch fixes all call sites of safe_name().
Mathieu Malaterre reported the memory leak on boot:
On my PowerMac device-tree would generate a duplicate name:
[ 0.023043] device-tree: Duplicate name in PowerPC,G4@0, renamed to "l2-cache#1"
in this case a newly allocated name is generated by `safe_name`. However
in this case it is never deallocated.
The bug was found using kmemleak reported as:
unreferenced object 0xdf532e60 (size 32):
comm "swapper", pid 1, jiffies 4294892300 (age 1993.532s)
hex dump (first 32 bytes):
6c 32 2d 63 61 63 68 65 23 31 00 dd e4 dd 1e c2 l2-cache#1......
ec d4 ba ce 04 ec cc de 8e 85 e9 ca c4 ec cc 9e ................
backtrace:
[<c02d3350>] kvasprintf+0x64/0xc8
[<c02d3400>] kasprintf+0x4c/0x5c
[<c0453814>] safe_name.isra.1+0x80/0xc4
[<c04545d8>] __of_attach_node_sysfs+0x6c/0x11c
[<c075f21c>] of_core_init+0x8c/0xf8
[<c0729594>] kernel_init_freeable+0xd4/0x208
[<c00047e8>] kernel_init+0x24/0x11c
[<c00158ec>] ret_from_kernel_thread+0x5c/0x64
Link: https://bugzilla.kernel.org/show_bug.cgi?id=120331
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Reported-by: mathieu.malaterre@gmail.com
Tested-by: Mathieu Malaterre <mathieu.malaterre@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
This reverts commit b80443c221.
After covering to use helper of_platform_default_populate() to populate
the default bus, no need to export of_default_bus_match_table anymore.
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Use helper of_platform_default_populate() in linux/of_platform
when possible, instead of calling of_platform_populate() with
the default match table.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The arch code calls of_platform_populate() with default match table
when it wants to populate default bus.
This patch introduce a new of_platform_default_populate_init() and make it
arch_initcall_sync(it should be later than some iommu configration, eg,
of_iommu_init() and swiotlb_late_init in arm64), then we can finish above
job in common method.
In order to avoid the default bus being populated twice, simply checking
the flag of bus node whether has be set OF_POPULATED_BUS or not.
After that, we can safely remove the caller in arch code.
Btw, add debug print in of_platform_populate(), and use __func__ to
print function's name of of_platform_bus_create().
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The fixed_phy driver doesn't have to be built-in, and it's
important that of_mdio supports it even if it's a module.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is unflattening device sub-tree blob if @dad passed to
the function is valid. Currently, this functionality is used by PPC
PowerNV PCI hotplug driver only. There are possibly multiple nodes
in the first level of depth, fdt_next_node() bails immediately when
@depth becomes negative before the second device node can be probed
successfully. It leads to the device nodes except the first one won't
be unflattened successfully.
This fixes the issue by setting the initial depth (@inital_depth) to
1 when this function is called to unflatten device sub-tree blob. No
logic changes when this function is used to unflatten non-sub-tree
blob.
Cc: Rhyland Klein <rklein@nvidia.com>
Fixes: 78c44d910 ("drivers/of: Fix depth when unflattening devicetree")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Rhyland Klein <rklein@nvidia.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Change return value back to -ENODEV when no region is defined for given
device. This restores old behavior of this function, as some drivers rely
on such error code.
Fixes: 59ce403972 ("of: reserved_mem: add support for using more than
one region for given device")
Reported-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
pageblock_order can be (at least) an unsigned int or an unsigned long
depending on the kernel config and architecture, so use max_t(unsigned
long ...) when comparing it.
fixes these warnings:
In file included from include/linux/list.h:8:0,
from include/linux/kobject.h:20,
from include/linux/of.h:21,
from drivers/of/of_reserved_mem.c:17:
drivers/of/of_reserved_mem.c: In function ‘__reserved_mem_alloc_size’:
include/linux/kernel.h:748:17: warning: comparison of distinct pointer types lacks a cast
(void) (&_max1 == &_max2); \
^
include/linux/kernel.h:747:9: note: in definition of macro ‘max’
typeof(y) _max2 = (y); \
^
drivers/of/of_reserved_mem.c:131:48: note: in expansion of macro ‘max’
align = max(align, (phys_addr_t)PAGE_SIZE << max(MAX_ORDER - 1, pageblock_ord
^
include/linux/kernel.h:748:17: warning: comparison of distinct pointer types lacks a cast
(void) (&_max1 == &_max2); \
^
include/linux/kernel.h:747:21: note: in definition of macro ‘max’
typeof(y) _max2 = (y); \
^
drivers/of/of_reserved_mem.c:131:48: note: in expansion of macro ‘max’
align = max(align, (phys_addr_t)PAGE_SIZE << max(MAX_ORDER - 1, pageblock_ord
^
Fixes: 1cc8e3458b ("drivers: of: of_reserved_mem: fixup the alignment with CMA setup")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rob Herring <robh@kernel.org>
There was an alignment mismatch issue for CMA and it was fixed by
commit 1cc8e3458b ("drivers: of: of_reserved_mem: fixup the alignment with CMA setup").
However the way of the commit considers not only dma-contiguous(CMA) but also
dma-coherent which has no that requirement.
This patch checks more to distinguish dma-contiguous(CMA) from dma-coherent.
Signed-off-by: Jaewon Kim <jaewon31.kim@samsung.com>
Acked-by: Jason Liu <r64343@freescale.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
[robh: remove erroneous opening bracket]
Signed-off-by: Rob Herring <robh@kernel.org>
The kernel-doc for the of_irq_get[_byname]() is clearly inadequate in
describing the return values -- of_irq_get_byname() is documented better
than of_irq_get() but it still doesn't mention that 0 is returned iff
irq_create_of_mapping() fails (it doesn't return an error code in this
case). Document all possible return value variants, making the writing
of the word "IRQ" consistent, while at it...
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Fixes: ad69674e73 ("of/irq: do irq resolution in platform_get_irq_byname()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
CC: stable@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
This patch allows device drivers to initialize more than one reserved
memory region assigned to given device. When driver needs to use more
than one reserved memory region, it should allocate child devices and
initialize regions by index for each of its child devices.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rework numa_add_memblk() to update the parameter "u64 size" to "u64
end", this will make it consistent with x86 and simplifies the arm64
ACPI NUMA code to be added later.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
First cycle with Boris as NAND maintainer! Many (most) bullets stolen from him.
Generic:
* Migrated NAND LED trigger to be a generic MTD trigger
NAND:
* Introduction of the "ECC algorithm" concept, to avoid overloading the ECC
mode field too much more
* Replaced the nand_ecclayout infrastructure with something a little more
flexible (finally!) and future proof
* Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some of
this into their own tree as well
* Prepare the sunxi NAND driver to receive DMA support
* Handle bitflips in erased pages on GPMI revisions that do not support
this in hardware.
SPI NOR:
* Start using the spi_flash_read() API for SPI drivers that support it (i.e.,
SPI drivers with special memory-mapped flash modes)
And other small scattered improvments.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXQ9oUAAoJEFySrpd9RFgttf0P/3oIVCvLHSFIsi7XiUusWJWk
Cb+xW3ujFd2kNUqAQGnyvPUGU1amgjAjy2kwMpvpOG07DVgSnxQVGaQLins8Zwpw
auWxH8llISmC6UkNsS1jV0d7KzSMCT2Ne+BenRAn68kq3ovXPPB3B19B6dFj8ail
s83ajoZhsn1+eyctiKtbhXgZWkJHlRmBeXPKAJcS0lBcSibR+6N+O//JEAMnyYvc
7azuw0KMVwQNnNYFAfd9dilV5juZ9bZptTJYH7XuF+44FhxmSKvTX2a9gmp0C4Bm
FszUiPrIWF+t98nSQxxSn/zPlyllFyoisa6F7eGnDHIz+bH0Emf2oVwsSG5ASl42
XTml0kB0jCfuBfgAiyhYU2Uds7rSYs/ZcHr3iPgpUY3Sc3dgoArDdahMJXwqaoa8
UdChu6A+rjhi9PqhzNNVTarbilp3pOVgKAUVEWTdpQ1wGU4c+9SNlTTwhPy4g7RB
uKlqbMeiZ/5rPiihaMUNtzxMxSe9OGYW2HVNVExvmlF2Ca42M1xJJBMlAA6IIXyS
35d3Y4F5zPP7U6GCVla06WHkL5ahXJWmI0Xhf+2jCnDMipeAl6eCEiAJY5EmvAnr
FTpZ4qkspED69mO8oZW9ORje0n6PCm4XPOi4Vl8kci8tlBsEJMk9jaedWwGlZkRk
I5leUP4NEougvuHce2Cn
=J6KN
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
- Rewrite of the unflattening code to avoid recursion and lessen the
stack usage.
- Rewrite of the phandle args parsing code to get rid of the fixed args
size. This is needed for IOMMU code.
- Sync to latest dtc which adds more dts style checking. These warnings
are enabled with "W=1" compiles.
- Tegra documentation updates related to the above warnings.
- A bunch of spelling and other doc fixes.
- Various vendor prefix additions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=s+gW
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Rewrite of the unflattening code to avoid recursion and lessen the
stack usage.
- Rewrite of the phandle args parsing code to get rid of the fixed args
size. This is needed for IOMMU code.
- Sync to latest dtc which adds more dts style checking. These
warnings are enabled with "W=1" compiles.
- Tegra documentation updates related to the above warnings.
- A bunch of spelling and other doc fixes.
- Various vendor prefix additions.
* tag 'devicetree-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (52 commits)
devicetree: Add Creative Technology vendor id
gpio: dt-bindings: add ibm,ppc4xx-gpio binding
of/unittest: Remove unnecessary module.h header inclusion
drivers/of: Fix build warning in populate_node()
drivers/of: Fix depth when unflattening devicetree
of: dynamic: changeset prop-update revert fix
drivers/of: Export of_detach_node()
drivers/of: Return allocated memory from of_fdt_unflatten_tree()
drivers/of: Specify parent node in of_fdt_unflatten_tree()
drivers/of: Rename unflatten_dt_node()
drivers/of: Avoid recursively calling unflatten_dt_node()
drivers/of: Split unflatten_dt_node()
of: include errno.h in of_graph.h
of: document refcount incrementation of of_get_cpu_node()
Documentation: dt: soc: fix spelling mistakes
Documentation: dt: power: fix spelling mistake
Documentation: dt: pinctrl: fix spelling mistake
Documentation: dt: opp: fix spelling mistake
Documentation: dt: net: fix spelling mistakes
Documentation: dt: mtd: fix spelling mistake
...
Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie, Lennart
Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring, Michael
Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras, Rashmica Gupta,
Russell Currey, Suraj Jitindar Singh, Thiago Jung Bauermann, Valentin
Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell" from Guilherme G. Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme G. Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled from Ian Munsie
- Check periodically the coherent platform function's state from Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes, an erratum
workaround, and a kconfig dependency fix."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YvyQ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie,
Lennart Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring,
Michael Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras,
Rashmica Gupta, Russell Currey, Suraj Jitindar Singh, Thiago Jung
Bauermann, Valentin Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan
Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
from Guilherme G Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme
G Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica
Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe
Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic
Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian
Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs
from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled
from Ian Munsie
- Check periodically the coherent platform function's state from
Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes,
an erratum workaround, and a kconfig dependency fix."
* tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (192 commits)
powerpc/86xx: Fix PCI interrupt map definition
powerpc/86xx: Move pci1 definition to the include file
powerpc/fsl: Fix build of the dtb embedded kernel images
powerpc/fsl: Fix rcpm compatible string
powerpc/fsl: Remove FSL_SOC dependency from FSL_LBC
powerpc/fsl-pci: Add a workaround for PCI 5 errata
powerpc/fsl: Fix SPI compatible on t208xrdb and t1040rdb
powerpc/powernv/npu: Add PE to PHB's list
powerpc/powernv: Fix insufficient memory allocation
powerpc/iommu: Remove the dependency on EEH struct in DDW mechanism
Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
powerpc/eeh: Drop unnecessary label in eeh_pe_change_owner()
powerpc/eeh: Ignore handlers in eeh_pe_reset_and_recover()
powerpc/eeh: Restore initial state in eeh_pe_reset_and_recover()
powerpc/eeh: Don't report error in eeh_pe_reset_and_recover()
Revert "powerpc/powernv: Exclude root bus in pnv_pci_reset_secondary_bus()"
powerpc/powernv/npu: Enable NVLink pass through
powerpc/powernv/npu: Rework TCE Kill handling
powerpc/powernv/npu: Add set/unset window helpers
powerpc/powernv/ioda2: Export debug helper pe_level_printk()
...
Pull i2c updates from Wolfram Sang:
- Peter Rosin did some major rework on the locking of i2c muxes by
seperating parent-locked muxes and mux-locked muxes.
This avoids deadlocks/workarounds when the mux itself needs i2c
commands for muxing. And as a side-effect, other workarounds in the
media layer could be eliminated. Also, Peter stepped up as the i2c
mux maintainer and will keep an eye on these changes.
- major updates to the octeon driver
- add a helper to the core to generate the address+rw_bit octal and
make drivers use it
- quite a bunch of driver updates
* 'i2c/for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (84 commits)
i2c: rcar: add DMA support
i2c: st: Implement bus clear
i2c: only check scl functions when using generic recovery
i2c: algo-bit: declare i2c_bit_quirk_no_clk_stretch as static
i2c: tegra: disable clock before returning error
[media] rtl2832: regmap is aware of lockdep, drop local locking hack
[media] rtl2832_sdr: get rid of empty regmap wrappers
[media] rtl2832: change the i2c gate to be mux-locked
[media] si2168: change the i2c gate to be mux-locked
iio: imu: inv_mpu6050: change the i2c gate to be mux-locked
i2c: mux: document i2c muxes and elaborate on parent-/mux-locked muxes
i2c: mux: relax locking of the top i2c adapter during mux-locked muxing
i2c: muxes always lock the parent adapter
i2c: allow adapter drivers to override the adapter locking
i2c: uniphier: add "\n" at the end of error log
i2c: mv64xxx: remove CONFIG_HAVE_CLK conditionals
i2c: mv64xxx: use clk_{prepare_enable,disable_unprepare}
i2c: mv64xxx: handle probe deferral for the clock
i2c: mv64xxx: enable the driver on ARCH_MVEBU
i2c: octeon: Add workaround for broken irqs on CN3860
...
The updates include:
* Rate limiting for the VT-d fault handler
* Remove statistics code from the AMD IOMMU driver. It is unused
and should be replaced by something more generic if needed
* Per-domain pagesize-bitmaps in IOMMU core code to support
systems with different types of IOMMUs
* Support for ACPI devices in the AMD IOMMU driver
* 4GB mode support for Mediatek IOMMU driver
* ARM-SMMU updates from Will Deacon:
- Support for 64k pages with SMMUv1 implementations
(e.g MMU-401)
- Remove open-coded 64-bit MMIO accessors
- Initial support for 16-bit VMIDs, as supported by some
ThunderX SMMU implementations
- A couple of errata workarounds for silicon in the
field
* Various fixes here and there
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJXPeM1AAoJECvwRC2XARrjA2QP/2Cz+pVkpQCuvhAse57eN4rB
wWXKTjqSFZ4PcA3Vu5yvX6XMv15g46xXFJAhf2spE5//8+xgFfYBgkBRpnqu1brw
SL6f8A912MnfMRgWqcdKkJNeHbiN0kOvcIQv1J8GNfciqMiyYFhiLP6fFiRmWR/F
XDBjUeFZ5+Uwf1BAGqw0cVPexeakEbsLHUGqxFsh5g2T4i43aHzO2HJT3IdwWHDt
F2ivs8gNFGBeJEyzhW8TD0rOEEyHAnM3N18qPEU9+dD0UmjnTQPymEZSbsGW5d4j
Cn40QYlA+Zmbwgx6LaDVChzQyRJu6O3uvFThyRviiYKCri/Nc9cUT4vHsFGU4MXb
1d3bqrgzaw7vw31BN7S1Py3MV+WpVnEYjFm2O+hW28OjtSpm6ZvbI8wc0rF4UT/I
KgL0gSeA8tp25uVISM+ktpIrObYsAcoCz8nvurpDv2AGkKRzhyoSze0Jg43rusD8
BH7iFWu1LRPlulTGlrHMtNmbZeEApUPbObcQAOcrBOj9vjuFaZ8qduZmB+hwS2iV
p9atn+54LmGO0LuzqsGrhApIeXTeTZSrGyjlbUADWBJlTw8Xyk/CR39Wf3m/Xmpr
DiJ/5oa8SKQtNbwvbScn1+sInNWP/pH/JgnRO3Yvqth8HWF/DlpzNj5XxAB8czwr
qjk9WjpEXun50ocPFQeS
=jpPD
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"The updates include:
- rate limiting for the VT-d fault handler
- remove statistics code from the AMD IOMMU driver. It is unused and
should be replaced by something more generic if needed
- per-domain pagesize-bitmaps in IOMMU core code to support systems
with different types of IOMMUs
- support for ACPI devices in the AMD IOMMU driver
- 4GB mode support for Mediatek IOMMU driver
- ARM-SMMU updates from Will Deacon:
- support for 64k pages with SMMUv1 implementations (e.g MMU-401)
- remove open-coded 64-bit MMIO accessors
- initial support for 16-bit VMIDs, as supported by some ThunderX
SMMU implementations
- a couple of errata workarounds for silicon in the field
- various fixes here and there"
* tag 'iommu-updates-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (44 commits)
iommu/arm-smmu: Use per-domain page sizes.
iommu/amd: Remove statistics code
iommu/dma: Finish optimising higher-order allocations
iommu: Allow selecting page sizes per domain
iommu: of: enforce const-ness of struct iommu_ops
iommu: remove unused priv field from struct iommu_ops
iommu/dma: Implement scatterlist segment merging
iommu/arm-smmu: Clear cache lock bit of ACR
iommu/arm-smmu: Support SMMUv1 64KB supplement
iommu/arm-smmu: Decouple context format from kernel config
iommu/arm-smmu: Tidy up 64-bit/atomic I/O accesses
io-64-nonatomic: Add relaxed accessor variants
iommu/arm-smmu: Work around MMU-500 prefetch errata
iommu/arm-smmu: Convert ThunderX workaround to new method
iommu/arm-smmu: Differentiate specific implementations
iommu/arm-smmu: Workaround for ThunderX erratum #27704
iommu/arm-smmu: Add support for 16 bit VMID
iommu/amd: Move get_device_id() and friends to beginning of file
iommu/amd: Don't use IS_ERR_VALUE to check integer values
iommu/amd: Signedness bug in acpihid_device_group()
...
Enumeration
Refine PCI support check in pcibios_init() (Adrian-Ken Rueegsegger)
Provide common functions for ECAM mapping (Jayachandran C)
Allow all PCIe services on non-ACPI host bridges (Jon Derrick)
Remove return values from pcie_port_platform_notify() and relatives (Jon Derrick)
Widen portdrv service type from 4 bits to 8 bits (Keith Busch)
Add Downstream Port Containment portdrv service type (Keith Busch)
Add Downstream Port Containment driver (Keith Busch)
Resource management
Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs (Alex Williamson)
Supply CPU physical address (not bus address) to iomem_is_exclusive() (Bjorn Helgaas)
alpha: Call iomem_is_exclusive() for IORESOURCE_MEM, but not IORESOURCE_IO (Bjorn Helgaas)
Mark Broadwell-EP Home Agent 1 as having non-compliant BARs (Prarit Bhargava)
Disable all BAR sizing for devices with non-compliant BARs (Prarit Bhargava)
Move PCI I/O space management from OF to PCI core code (Tomasz Nowicki)
PCI device hotplug
acpiphp_ibm: Avoid uninitialized variable reference (Dan Carpenter)
Use cached copy of PCI_EXP_SLTCAP_HPC bit (Lukas Wunner)
Virtualization
Mark Intel i40e NIC INTx masking as broken (Alex Williamson)
Reverse standard ACS vs device-specific ACS enabling (Alex Williamson)
Work around Intel Sunrise Point PCH incorrect ACS capability (Alex Williamson)
IOMMU
Add pci_add_dma_alias() to abstract implementation (Bjorn Helgaas)
Move informational printk to pci_add_dma_alias() (Bjorn Helgaas)
Add support for multiple DMA aliases (Jacek Lawrynowicz)
Add DMA alias quirk for mic_x200_dma (Jacek Lawrynowicz)
Thunderbolt
Fix double free of drom buffer (Andreas Noever)
Add Intel Thunderbolt device IDs (Lukas Wunner)
Fix typos and magic number (Lukas Wunner)
Support 1st gen Light Ridge controller (Lukas Wunner)
Generic host bridge driver
Use generic ECAM API (Jayachandran C)
Cavium ThunderX host bridge driver
Don't clobber read-only bits in bridge config registers (David Daney)
Use generic ECAM API (Jayachandran C)
Freescale i.MX6 host bridge driver
Use enum instead of bool for variant indicator (Andrey Smirnov)
Implement reset sequence for i.MX6+ (Andrey Smirnov)
Factor out ref clock enable (Bjorn Helgaas)
Add initial imx6sx support (Christoph Fritz)
Add reset-gpio-active-high boolean property to DT (Petr Štetiar)
Add DT property for link gen, default to Gen1 (Tim Harvey)
dts: Specify imx6qp version of PCIe core (Andrey Smirnov)
dts: Fix PCIe reset GPIO polarity on Toradex Apalis Ixora (Petr Štetiar)
Marvell Armada host bridge driver
add DT binding for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Add driver for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Marvell MVEBU host bridge driver
Constify mvebu_pcie_pm_ops structure (Jisheng Zhang)
Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for mvebu_pcie_pm_ops (Jisheng Zhang)
Microsoft Hyper-V host bridge driver
Report resources release after stopping the bus (Vitaly Kuznetsov)
Add explicit barriers to config space access (Vitaly Kuznetsov)
Renesas R-Car host bridge driver
Select PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
Synopsys DesignWare host bridge driver
Remove incorrect RC memory base/limit configuration (Gabriele Paoloni)
Move Root Complex setup code to dw_pcie_setup_rc() (Jisheng Zhang)
TI Keystone host bridge driver
Add error IRQ handler (Murali Karicheri)
Remove unnecessary goto statement (Murali Karicheri)
Miscellaneous
Fix spelling errors (Colin Ian King)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=68Iz
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Refine PCI support check in pcibios_init() (Adrian-Ken Rueegsegger)
- Provide common functions for ECAM mapping (Jayachandran C)
- Allow all PCIe services on non-ACPI host bridges (Jon Derrick)
- Remove return values from pcie_port_platform_notify() and relatives (Jon Derrick)
- Widen portdrv service type from 4 bits to 8 bits (Keith Busch)
- Add Downstream Port Containment portdrv service type (Keith Busch)
- Add Downstream Port Containment driver (Keith Busch)
Resource management:
- Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs (Alex Williamson)
- Supply CPU physical address (not bus address) to iomem_is_exclusive() (Bjorn Helgaas)
- alpha: Call iomem_is_exclusive() for IORESOURCE_MEM, but not IORESOURCE_IO (Bjorn Helgaas)
- Mark Broadwell-EP Home Agent 1 as having non-compliant BARs (Prarit Bhargava)
- Disable all BAR sizing for devices with non-compliant BARs (Prarit Bhargava)
- Move PCI I/O space management from OF to PCI core code (Tomasz Nowicki)
PCI device hotplug:
- acpiphp_ibm: Avoid uninitialized variable reference (Dan Carpenter)
- Use cached copy of PCI_EXP_SLTCAP_HPC bit (Lukas Wunner)
Virtualization:
- Mark Intel i40e NIC INTx masking as broken (Alex Williamson)
- Reverse standard ACS vs device-specific ACS enabling (Alex Williamson)
- Work around Intel Sunrise Point PCH incorrect ACS capability (Alex Williamson)
IOMMU:
- Add pci_add_dma_alias() to abstract implementation (Bjorn Helgaas)
- Move informational printk to pci_add_dma_alias() (Bjorn Helgaas)
- Add support for multiple DMA aliases (Jacek Lawrynowicz)
- Add DMA alias quirk for mic_x200_dma (Jacek Lawrynowicz)
Thunderbolt:
- Fix double free of drom buffer (Andreas Noever)
- Add Intel Thunderbolt device IDs (Lukas Wunner)
- Fix typos and magic number (Lukas Wunner)
- Support 1st gen Light Ridge controller (Lukas Wunner)
Generic host bridge driver:
- Use generic ECAM API (Jayachandran C)
Cavium ThunderX host bridge driver:
- Don't clobber read-only bits in bridge config registers (David Daney)
- Use generic ECAM API (Jayachandran C)
Freescale i.MX6 host bridge driver:
- Use enum instead of bool for variant indicator (Andrey Smirnov)
- Implement reset sequence for i.MX6+ (Andrey Smirnov)
- Factor out ref clock enable (Bjorn Helgaas)
- Add initial imx6sx support (Christoph Fritz)
- Add reset-gpio-active-high boolean property to DT (Petr Štetiar)
- Add DT property for link gen, default to Gen1 (Tim Harvey)
- dts: Specify imx6qp version of PCIe core (Andrey Smirnov)
- dts: Fix PCIe reset GPIO polarity on Toradex Apalis Ixora (Petr Štetiar)
Marvell Armada host bridge driver:
- add DT binding for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
- Add driver for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Marvell MVEBU host bridge driver:
- Constify mvebu_pcie_pm_ops structure (Jisheng Zhang)
- Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for mvebu_pcie_pm_ops (Jisheng Zhang)
Microsoft Hyper-V host bridge driver:
- Report resources release after stopping the bus (Vitaly Kuznetsov)
- Add explicit barriers to config space access (Vitaly Kuznetsov)
Renesas R-Car host bridge driver:
- Select PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
Synopsys DesignWare host bridge driver:
- Remove incorrect RC memory base/limit configuration (Gabriele Paoloni)
- Move Root Complex setup code to dw_pcie_setup_rc() (Jisheng Zhang)
TI Keystone host bridge driver:
- Add error IRQ handler (Murali Karicheri)
- Remove unnecessary goto statement (Murali Karicheri)
Miscellaneous:
- Fix spelling errors (Colin Ian King)"
* tag 'pci-v4.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Disable all BAR sizing for devices with non-compliant BARs
x86/PCI: Mark Broadwell-EP Home Agent 1 as having non-compliant BARs
PCI: Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs
PCI, of: Move PCI I/O space management to PCI core code
PCI: generic, thunder: Use generic ECAM API
PCI: Provide common functions for ECAM mapping
PCI: hv: Add explicit barriers to config space access
PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Add Downstream Port Containment driver
PCI: Add Downstream Port Containment portdrv service type
PCI: Widen portdrv service type from 4 bits to 8 bits
PCI: designware: Remove incorrect RC memory base/limit configuration
PCI: hv: Report resources release after stopping the bus
ARM: dts: imx6qp: Specify imx6qp version of PCIe core
PCI: imx6: Implement reset sequence for i.MX6+
PCI: imx6: Use enum instead of bool for variant indicator
PCI: thunder: Don't clobber read-only bits in bridge config registers
thunderbolt: Fix double free of drom buffer
PCI: rcar: Select PCI_MSI_IRQ_DOMAIN
PCI: armada: Add driver for Marvell Armada 7K/8K PCIe controller
...
The OF_UNITTEST Kconfig symbol is bool so this unittest can only be
built-in and not build as a module. Also, nothing defined in this
header file used so is not necessary to include it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Function populate_node() is used to unflatten FDT blob to device
tree. It supports maximal 64 level of device nodes. There is one
array @fpsizes[64] tracking the full name length of last unflattened
device node in the corresponding level (index of element in the
array - 1). Build warning is seen with CONFIG_FRAME_WARN=1024 like
below on ARM64 as Geert reported. The issue can be reproduced on
PPC64 as well.
$ make drivers/of/fdt.o
drivers/of/fdt.c:443:1: warning: the frame size of 1136 bytes is \
larger than 1024 bytes [-Wframe-larger-than=]
This changes the data type of @fpsizes[i] from "unsigned long" to
"unsigned int" to avoid the build warning. The return value type
of populate_node() and its @fpsize argument is adjusted accordingly.
With this applied, 256 bytes saved from the stack frame on ARM64 and
PPC64 platforms and the above warning isn't seen.
Fixes: 50800082f1 ("drivers/of: Avoid recursively calling unflatten_dt_node()")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
When the implementation for unflatten_dt_node() changed from being
recursive to being non-recursive, it had a side effect of increasing the
depth passed to fdt_next_node() by 1. This is fine most of the time, but
it seems that when the end of the dtb is being parsed, it will cause the
FDT_END condition in fdt_next_node() to return a different value
(returning nextoffset instead of -FDT_ERR_NOTFOUND). This ends up passing
an FDT_ERR_TRUNCATED error back to the unflatten_dt_node() which then
sees that and complains "Error -8 processing FDT" causing boot to fail.
This patch simply avoids incrementing depth and uses modified accesses
for local array indices so that the depth is the same as it was before
the change as far as fdt_next_node() is concerned.
This problem was discovered trying to boot Tegra210-Smaug platforms.
Fixes: 50800082f1 ("drivers/of: Avoid recursively calling unflatten_dt_node()")
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[robh: squashed in KASAN fix from Rhyland]
Signed-off-by: Rob Herring <robh@kernel.org>
Traditionally we've had two separate branches for cleanups and non-critical
bug fixes, but both of these got smaller with each release and the differences
are rather unclear now, so it seems more appropriate to have a combined
branch.
The most notably change is for OMAP, which gets a small rework to simplify
handling of the AUXDATA mechanism used on machines that are not completely
DT based yet, along with other work that is used as preparation for dropping
the legacy board files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=au7y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanups-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups and fixes from Arnd Bergmann:
"Traditionally we've had two separate branches for cleanups and
non-critical bug fixes, but both of these got smaller with each
release and the differences are rather unclear now, so it seems more
appropriate to have a combined branch.
The most notable change is for OMAP, which gets a small rework to
simplify handling of the AUXDATA mechanism used on machines that are
not completely DT based yet, along with other work that is used as
preparation for dropping the legacy board files"
* tag 'armsoc-cleanups-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: exynos: Add interrupt line to MAX8997 PMIC on exynos4210-trats
ARM: dts: exynos: Fix regulator name to avoid forbidden character on exynos4210-trats
ARM: dts: exynos: Add MFC memory banks for Peach boards
ARM: OMAP2+: n900 needs MMC slot names for legacy user space
ARM: OMAP2+: Add more functions to pwm pdata for ir-rx51
ARM: debug: remove extraneous DEBUG_HI3716_UART option
ARM: OMAP2+: Simplify auxdata by using the generic match
of/platform: Allow secondary compatible match in of_dev_lookup
ARM: davinci: use IRQCHIP_DECLARE for cp_intc
ARM: davinci: remove unused DA8XX_NUM_UARTS
ARM: davinci: simplify call to of populate
ARM: DaVinci USB: removed deprecated properties from MUSB config
ARM: rockchip: Fix use of plain integer as NULL pointer
ARM: realview: hide unused 'pmu_device' object
soc: versatile: dynamically detect RealView HBI numbers
Pull networking updates from David Miller:
"Highlights:
1) Support SPI based w5100 devices, from Akinobu Mita.
2) Partial Segmentation Offload, from Alexander Duyck.
3) Add GMAC4 support to stmmac driver, from Alexandre TORGUE.
4) Allow cls_flower stats offload, from Amir Vadai.
5) Implement bpf blinding, from Daniel Borkmann.
6) Optimize _ASYNC_ bit twiddling on sockets, unless the socket is
actually using FASYNC these atomics are superfluous. From Eric
Dumazet.
7) Run TCP more preemptibly, also from Eric Dumazet.
8) Support LED blinking, EEPROM dumps, and rxvlan offloading in mlx5e
driver, from Gal Pressman.
9) Allow creating ppp devices via rtnetlink, from Guillaume Nault.
10) Improve BPF usage documentation, from Jesper Dangaard Brouer.
11) Support tunneling offloads in qed, from Manish Chopra.
12) aRFS offloading in mlx5e, from Maor Gottlieb.
13) Add RFS and RPS support to SCTP protocol, from Marcelo Ricardo
Leitner.
14) Add MSG_EOR support to TCP, this allows controlling packet
coalescing on application record boundaries for more accurate
socket timestamp sampling. From Martin KaFai Lau.
15) Fix alignment of 64-bit netlink attributes across the board, from
Nicolas Dichtel.
16) Per-vlan stats in bridging, from Nikolay Aleksandrov.
17) Several conversions of drivers to ethtool ksettings, from Philippe
Reynes.
18) Checksum neutral ILA in ipv6, from Tom Herbert.
19) Factorize all of the various marvell dsa drivers into one, from
Vivien Didelot
20) Add VF support to qed driver, from Yuval Mintz"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1649 commits)
Revert "phy dp83867: Fix compilation with CONFIG_OF_MDIO=m"
Revert "phy dp83867: Make rgmii parameters optional"
r8169: default to 64-bit DMA on recent PCIe chips
phy dp83867: Make rgmii parameters optional
phy dp83867: Fix compilation with CONFIG_OF_MDIO=m
bpf: arm64: remove callee-save registers use for tmp registers
asix: Fix offset calculation in asix_rx_fixup() causing slow transmissions
switchdev: pass pointer to fib_info instead of copy
net_sched: close another race condition in tcf_mirred_release()
tipc: fix nametable publication field in nl compat
drivers: net: Don't print unpopulated net_device name
qed: add support for dcbx.
ravb: Add missing free_irq() calls to ravb_close()
qed: Remove a stray tab
net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fec-mpc52xx: use phydev from struct net_device
bpf, doc: fix typo on bpf_asm descriptions
stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fs-enet: use phydev from struct net_device
...
When reverting an update property changeset entry that created a
property the reverse operation is a remove property and not an update.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This returns the allocate memory chunk, storing the unflattened device
tree, from of_fdt_unflatten_tree() so that memory chunk can be released
on demand in PowerNV PCI hotplug driver.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
This adds one more argument to of_fdt_unflatten_tree() to specify
the parent node of the FDT blob that is going to be unflattened.
In the result, the function can be used to unflatten FDT blob that
represents device sub-tree in PowerNV PCI hotplug driver.
Cc: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This renames unflatten_dt_node() to unflatten_dt_nodes() as it
populates multiple device nodes from FDT blob. No logical changes
introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
In current implementation, unflatten_dt_node() is called recursively
to unflatten device nodes in FDT blob. It's stress to limited stack
capacity, especially to adopt the function to unflatten device sub-tree
that possibly has multiple root nodes. In that case, we runs out of
stack and the system can't boot up successfully.
In order to reuse the function to unflatten device sub-tree, this avoids
calling the function recursively, meaning the device nodes are unflattened
in one call on unflatten_dt_node(): two arrays are introduced to track the
parent path size and the device node of current level of depth, which will
be used by the device node on next level of depth to be unflattened. All
device nodes in more than 64 level of depth are dropped and hopefully,
the system can boot up successfully with the partial device-tree.
Also, the parameter "poffset" and "fpsize" are unused and dropped and the
parameter "dryrun" is figured out from "mem == NULL". Besides, the return
value of the function is changed to indicate the size of memory consumed by
the unflatten device tree or error code.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The function unflatten_dt_node() is called recursively to unflatten
device nodes and properties in the FDT blob. It looks complicated
and hard to be understood.
This splits the function into 3 functions: populate_properties(),
populate_node() and unflatten_dt_node(). populate_properties(),
which is called by populate_node(), creates properties for the
indicated device node. The later one creates the device nodes
from FDT blob. populate_node() gets the offset in FDT blob for
next device nodes and then calls populate_node(). No logical
changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
No functional changes in this patch.
PCI I/O space mapping code does not depend on OF; therefore it can be moved
to PCI core code. This way we will be able to use it, e.g., in ACPI PCI
code.
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Liviu Dudau <Liviu.Dudau@arm.com>
The validity of the property input argument to of_remove_property() is
never checked within the function and thus it is possible to pass a null
value. It happens that this will be picked up in __of_remove_property()
as no matching property of the device node will be found and thus an
error will be returned, however once again there is no explicit check
for a null value. By the time this is detected 2 locks have already been
acquired which is completely unnecessary if the property to remove is
null.
Add an explicit check in the function of_remove_property() for a null
property value and return -ENODEV in this case, this is consistent with
what the previous return value would have been when the null value was
not detected and passed to __of_remove_property().
By moving an explicit check for the property paramenter into the
of_remove_property() function, this will remove the need to perform this
check in calling code before invocation of the of_remove_property()
function.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As a set of driver-provided callbacks and static data, there is no
compelling reason for struct iommu_ops to be mutable in core code, so
enforce const-ness throughout.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Now that all drivers go through nand_set_flash_node() to parse the generic
NAND properties, we can move all of_get_nand_xxx() helpers in to
nand_base.c, make them static and remove of_mtd.c and of_mtd.h.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add a check whether the 'struct device_node' pointer passed to
of_mdiobus_register() is an available (aka enabled) node in the Device
Tree.
Rationale for doing this are cases where an Ethernet MAC provides a MDIO
bus controller and node, and an additional Ethernet MAC might be
connecting its PHY/switches to that first MDIO bus controller, while
still embedding one internally which is therefore marked as "disabled".
Instead of sprinkling checks like these in callers of
of_mdiobus_register(), do this in a central location.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_phy_device() no longer returns NULL on error, we don't need
to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function increments refcount. This is worth noting.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This helper function can be used to copy the arguments of a
phandle to an array.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
With this macro any user can easily iterate over a list of
phandles. The patch also converts __of_parse_phandle_with_args()
to make use of the macro.
The of_count_phandle_with_args() function is not converted,
because the macro hides the return value of of_phandle_iterator_init(),
which is needed in there.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
The index = -1 case in __of_parse_phandle_with_args() is
used to just return the number of phandles. That special
case needs extra handling, so move it to the place where it
is needed: of_count_phandle_with_args().
This allows to further simplify __of_parse_phandle_with_args()
later on.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Move the code to walk over the phandles out of the loop in
__of_parse_phandle_with_args() to a separate function that
just works with the iterator handle: of_phandle_iterator_next().
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
This struct carrys all necessary information to iterate over
a list of phandles and extract the arguments. Add an
init-function for the iterator and make use of it in
__of_parse_phandle_with_args().
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
On arm CONFIG_CMDLINE_EXTEND does not append build-in
cmdline in kernel to U-boot parameters. Fix it here.
Theoretically this patch should repair kdump work where
it adds elfcorehdr= and memmap additional parameters
to second kernel.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
NAND subsystem is being slightly reworked to store ECC details in
separated fields. In future we'll want to add support for more DT
properties as specifying every possible setup with a single
"nand-ecc-mode" is a pretty bad idea.
To allow this let's add a helper that will support something like
"nand-ecc-algo" in future. Right now we use it for keeping backward
compatibility.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The results of of_mdiobus_register_{device|phy}() are never checked, so we
can make both these functions *void*...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree parsing for NUMA topology using device
"numa-node-id" property in distance-map and cpu nodes.
This is a complete rewrite of a previous patch by:
Ganapatrao Kulkarni<gkulkarni@caviumnetworks.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We currently try to match of_dev_auxdata based on compatible,
IO address, and device name. But in some cases we have multiple
instances of drivers that can use the same auxdata.
Let's add an additional secondary lookup for generic compatible
match for auxdata if no device specific match is found. This does
not change the existing matching, and still allows adding device
specific auxdata.
This simplifies things as specifying the IO address and device
name is prone errors as it requires maintaining an in kernel
database for each SoC.
To specify a generic match, all that is needed is to add a
OF_DEV_AUXDATA entry with no device instance specified:
OF_DEV_AUXDATA("pinctrl-single", 0, NULL, &pcs_pdata),
As the auxdata is already initialized only for the booted SoC,
there's not much of a chance of getting things wrong.
Let's also fix two checkpatch warnings while at it to add a
space before parenthesis in the for loop, and remove a comparison
to NULL by using !auxdata->compatible.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- New tool dtx_diff to diff DT files.
- Sync kernel's dtc/libfdt to current dtc repo master.
- Fix for reserved memory regions located in highmem.
- Document standard unit suffixes for DT properties.
- Various DT binding doc updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hz7v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- new tool 'dtx_diff' to diff DT files
- sync kernel's dtc/libfdt to current dtc repo master
- fix for reserved memory regions located in highmem
- document standard unit suffixes for DT properties
- various DT binding doc updates
* tag 'devicetree-for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: Add vendor prefix for eGalax_eMPIA Technology Inc
Input: ads7846: Add description how to use internal reference (ADS7846)
ARM: realview: add EB syscon variants to bindings
devicetree: bindings: ARM: Use "uV" for micro-volt
serial: fsl-imx-uart: Fix typo in fsl,dte-mode description
of: add 'const' for of_property_*_string*() parameter '*np'
of/unittest: fix infinite loop in of_unittest_destroy_tracked_overlays()
of: alloc anywhere from memblock if range not specified
kbuild: Allow using host dtc instead of kernel's copy
of: resolver: Add missing of_node_get and of_node_put
of: Add United Radiant Technology Corporation vendor prefix
dt/bindings: add documentation on standard property unit suffixes
scripts/dtc: Update to upstream commit b06e55c88b9b
ARM: boot: Add an implementation of strnlen for libfdt
scripts/dtc: dtx_diff - add info to error message
dtc: create tool to diff device trees
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
- Initial page table creation reworked to avoid breaking large block
mappings (huge pages) into smaller ones. The ARM architecture requires
break-before-make in such cases to avoid TLB conflicts but that's not
always possible on live page tables
- Kernel virtual memory layout: the kernel image is no longer linked to
the bottom of the linear mapping (PAGE_OFFSET) but at the bottom of
the vmalloc space, allowing the kernel to be loaded (nearly) anywhere
in physical RAM
- Kernel ASLR: position independent kernel Image and modules being
randomly mapped in the vmalloc space with the randomness is provided
by UEFI (efi_get_random_bytes() patches merged via the arm64 tree,
acked by Matt Fleming)
- Implement relative exception tables for arm64, required by KASLR
(initial code for ARCH_HAS_RELATIVE_EXTABLE added to lib/extable.c but
actual x86 conversion to deferred to 4.7 because of the merge
dependencies)
- Support for the User Access Override feature of ARMv8.2: this allows
uaccess functions (get_user etc.) to be implemented using LDTR/STTR
instructions. Such instructions, when run by the kernel, perform
unprivileged accesses adding an extra level of protection. The
set_fs() macro is used to "upgrade" such instruction to privileged
accesses via the UAO bit
- Half-precision floating point support (part of ARMv8.2)
- Optimisations for CPUs with or without a hardware prefetcher (using
run-time code patching)
- copy_page performance improvement to deal with 128 bytes at a time
- Sanity checks on the CPU capabilities (via CPUID) to prevent
incompatible secondary CPUs from being brought up (e.g. weird
big.LITTLE configurations)
- valid_user_regs() reworked for better sanity check of the sigcontext
information (restored pstate information)
- ACPI parking protocol implementation
- CONFIG_DEBUG_RODATA enabled by default
- VDSO code marked as read-only
- DEBUG_PAGEALLOC support
- ARCH_HAS_UBSAN_SANITIZE_ALL enabled
- Erratum workaround Cavium ThunderX SoC
- set_pte_at() fix for PROT_NONE mappings
- Code clean-ups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/oS+
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Here are the main arm64 updates for 4.6. There are some relatively
intrusive changes to support KASLR, the reworking of the kernel
virtual memory layout and initial page table creation.
Summary:
- Initial page table creation reworked to avoid breaking large block
mappings (huge pages) into smaller ones. The ARM architecture
requires break-before-make in such cases to avoid TLB conflicts but
that's not always possible on live page tables
- Kernel virtual memory layout: the kernel image is no longer linked
to the bottom of the linear mapping (PAGE_OFFSET) but at the bottom
of the vmalloc space, allowing the kernel to be loaded (nearly)
anywhere in physical RAM
- Kernel ASLR: position independent kernel Image and modules being
randomly mapped in the vmalloc space with the randomness is
provided by UEFI (efi_get_random_bytes() patches merged via the
arm64 tree, acked by Matt Fleming)
- Implement relative exception tables for arm64, required by KASLR
(initial code for ARCH_HAS_RELATIVE_EXTABLE added to lib/extable.c
but actual x86 conversion to deferred to 4.7 because of the merge
dependencies)
- Support for the User Access Override feature of ARMv8.2: this
allows uaccess functions (get_user etc.) to be implemented using
LDTR/STTR instructions. Such instructions, when run by the kernel,
perform unprivileged accesses adding an extra level of protection.
The set_fs() macro is used to "upgrade" such instruction to
privileged accesses via the UAO bit
- Half-precision floating point support (part of ARMv8.2)
- Optimisations for CPUs with or without a hardware prefetcher (using
run-time code patching)
- copy_page performance improvement to deal with 128 bytes at a time
- Sanity checks on the CPU capabilities (via CPUID) to prevent
incompatible secondary CPUs from being brought up (e.g. weird
big.LITTLE configurations)
- valid_user_regs() reworked for better sanity check of the
sigcontext information (restored pstate information)
- ACPI parking protocol implementation
- CONFIG_DEBUG_RODATA enabled by default
- VDSO code marked as read-only
- DEBUG_PAGEALLOC support
- ARCH_HAS_UBSAN_SANITIZE_ALL enabled
- Erratum workaround Cavium ThunderX SoC
- set_pte_at() fix for PROT_NONE mappings
- Code clean-ups"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (99 commits)
arm64: kasan: Fix zero shadow mapping overriding kernel image shadow
arm64: kasan: Use actual memory node when populating the kernel image shadow
arm64: Update PTE_RDONLY in set_pte_at() for PROT_NONE permission
arm64: Fix misspellings in comments.
arm64: efi: add missing frame pointer assignment
arm64: make mrs_s prefixing implicit in read_cpuid
arm64: enable CONFIG_DEBUG_RODATA by default
arm64: Rework valid_user_regs
arm64: mm: check at build time that PAGE_OFFSET divides the VA space evenly
arm64: KVM: Move kvm_call_hyp back to its original localtion
arm64: mm: treat memstart_addr as a signed quantity
arm64: mm: list kernel sections in order
arm64: lse: deal with clobbered IP registers after branch via PLT
arm64: mm: dump: Use VA_START directly instead of private LOWEST_ADDR
arm64: kconfig: add submenu for 8.2 architectural features
arm64: kernel: acpi: fix ioremap in ACPI parking protocol cpu_postboot
arm64: Add support for Half precision floating point
arm64: Remove fixmap include fragility
arm64: Add workaround for Cavium erratum 27456
arm64: mm: Mark .rodata as RO
...
Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp8z8ACgkQMUfUDdst+ym1vwCgnOOCORaZyeQ4QrcxPAK5pHFn
VrMAoNHvDgNYtG+Hmzv25Lgp3HnysPin
=MLRG
-----END PGP SIGNATURE-----
Merge tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (220 commits)
serial: 8250: describe CONFIG_SERIAL_8250_RSA
serial: samsung: optimize UART rx fifo access routine
serial: pl011: add mark/space parity support
serial: sa1100: make sa1100_register_uart_fns a function
tty: serial: 8250: add MOXA Smartio MUE boards support
serial: 8250: convert drivers to use up_to_u8250p()
serial: 8250/mediatek: fix building with SERIAL_8250=m
serial: 8250/ingenic: fix building with SERIAL_8250=m
serial: 8250/uniphier: fix modular build
Revert "drivers/tty/serial: make 8250/8250_ingenic.c explicitly non-modular"
Revert "drivers/tty/serial: make 8250/8250_mtk.c explicitly non-modular"
serial: mvebu-uart: initial support for Armada-3700 serial port
serial: mctrl_gpio: Add missing module license
serial: ifx6x60: avoid uninitialized variable use
tty/serial: at91: fix bad offset for UART timeout register
tty/serial: at91: restore dynamic driver binding
serial: 8250: Add hardware dependency to RT288X option
TTY, devpts: document pty count limiting
tty: goldfish: support platform_device with id -1
drivers: tty: goldfish: Add device tree bindings
...
PTR_ERR_OR_ZERO() is open coded in of_phy_register_fixed_link(), so just
call it directly...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR_OR_NULL() is open coded in of_mdiobus_register_phy(), so just call
it directly...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio_device_create() never returns NULL, thus checking for it in
of_mdiobus_register_device() is pointless...
Suggested-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_property_{read,count,match}_string* family of functions never
modify the struct device_node pointer that is passed in, so there is no
reason for it to be non-const. Equivalent functions for all other types
already take a 'const struct device_node *np'.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
of_overlay_destroy() can return `-ENODEV' error code once it
failed to find the requested overlay in `ov_idr'. However,
of_unittest_destroy_tracked_overlays() does not handle this
error code correctly and continues to call of_overlay_destroy()
on the 'missing' overlay over and over again. This results in
a printk flood
[..]
[ 33.497583] of_overlay_destroy: Could not find overlay #6
[ 33.497583] of_overlay_destroy: Could not find overlay #6
[ 33.497584] ### dt-test ### of_unittest_destroy_tracked_overlays: overlay destroy failed for #6
[ 33.497584] ### dt-test ### of_unittest_destroy_tracked_overlays: overlay destroy failed for #6
[ 33.497586] of_overlay_destroy: Could not find overlay #6
[ 33.497586] of_overlay_destroy: Could not find overlay #6
[ 33.497587] ### dt-test ### of_unittest_destroy_tracked_overlays: overlay destroy failed for #6
[ 33.497587] ### dt-test ### of_unittest_destroy_tracked_overlays: overlay destroy failed for #6
[..]
which is not really good due to printk design, and can lead to soft
lockups, hard lockups, etc. (depending on the context console_unlock()
is being called from). The problem has bee observed in real life
and reported by Ying Huang.
This patch does not address the root cause of missing overlay in
`ov_idr', it fixes the endless loop only.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: kernel test robot <ying.huang@linux.intel.com>
Link: lkml.kernel.org/r/87fuwk1c0o.fsf@yhuang-dev.intel.com
Signed-off-by: Rob Herring <robh@kernel.org>
early_init_dt_alloc_reserved_memory_arch passes end as 0 to
__memblock_alloc_base, when limits are not specified. But
__memblock_alloc_base takes end value of 0 as MEMBLOCK_ALLOC_ACCESSIBLE
and limits the end to memblock.current_limit. This results in regions
never being placed in HIGHMEM area, for e.g. CMA.
Let __memblock_alloc_base allocate from anywhere in memory if limits are
not specified.
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Vinayak Menon <vinmenon@codeaurora.org>
Cc: stable@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The 'flags' parameter of the of_phy_connect() function wasn't described
in the kernel-doc comment...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_mdiobus_register() declares the 'paddr' variable to hold the result of
the of_get_property() but only uses it once after that while the function
can be called directly from the *if* statement. Remove that variable and
switch to calling of_find_property() instead since we don't care about
the "reg" property's value anyway...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since architectures may not yet have their linear mapping up and running
when the initrd address is discovered from the DT, factor out the
assignment of initrd_start and initrd_end, so that an architecture can
override it and use the translation it needs.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
By default, early_init_dt_add_memory_arch() ignores memory below
the base of the kernel image since it won't be addressable via the
linear mapping. However, this is not appropriate anymore once we
decouple the kernel text mapping from the linear mapping, so archs
may want to drop the low limit entirely. So allow the minimum to be
overridden by setting MIN_MEMBLOCK_ADDR.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In __of_find_node_by_full_name, add an of_node_get when detecting the
desired element, to ensure that it ends up with a reference count that is
one greater than on entering the function.
Also in __of_find_node_by_full_name, add an of_node_put on breaking
out of the for_each_child_of_node loop, to ensure that the reference
count of the returned value is not double incremented. This change
was made using Coccinelle.
The semantic patch used for this is as follows:
// <smpl>
@@
expression e;
local idexpression n;
@@
for_each_child_of_node(..., n) {
... when != of_node_put(n)
when != e = n
(
return n;
|
+ of_node_put(n);
? return ...;
)
...
}
// </smpl
Finally, add an of_node_put in for_each_child_of_node in the function
__of_adjust_phandle_ref after the value returned by
__of_find_node_by_full_name is no longer useful.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The existing msi-map code is fine for shifting the entire RID space
upwards, but attempting finer-grained remapping reveals a bug. It turns
out that we are mistakenly treating the msi-base part as an offset, not
as a new base to remap onto, so things get squiffy when rid-base is
nonzero. Fix this, and at the same time add a sanity check against
having msi-map-mask clash with a nonzero rid-base, as that's another
thing one can easily get wrong.
CC: <stable@vger.kernel.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Stuart Yoder <stuart.yoder@nxp.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Commit ae46113196 ("of: of_mdio: Add a whitelist of PHY
compatibilities.") missed one compatible string used in in-tree DTBs:
in OCTEON, for selected boards, the kernel DTB pruning code will overwrite
the DTB compatible string with "marvell,88e1145", which is missing
from the whitelist. Add it.
The patch fixes broken networking on EdgeRouter Lite.
Fixes: ae46113196 ("of: of_mdio: Add a whitelist of PHY compatibilities.")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlycon may fail to initialize for a variety of reasons, most of
which log the default early param message. If the stdout-path node is
not found, log the path which was not found (and suppress the
default early param message).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanup the early DT/earlycon separation; remove the 'addr' parameter
from of_setup_earlycon() and get the uart phys addr directly with a
new wrapper function, of_flat_dt_translate_addr(). Limit
fdt_translate_address() to file scope.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Read the optional "reg-offset", "reg-shift", "reg-io-width" and endianness
properties and initialize the respective struct uart_port field if found.
NB: These bindings are common to several drivers and the values merely
indicate the default value; the registering earlycon setup() method can
simply override the values if required.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass-through any options string in the 'stdout-path' property to the
earlycon "driver" setup.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the console name embedded in the OF earlycon table by the
OF_EARLYCON_DECLARE() macro to initialize the struct console 'name'
and 'index' fields.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a single common table of struct earlycon_id for both command line
and devicetree. Re-define OF_EARLYCON_DECLARE() macro to instance a
unique earlycon declaration (the declaration is only guaranteed to be
unique within a compilation unit; separate compilation units must still
use unique earlycon names).
The semantics of OF_EARLYCON_DECLARE() is different; it declares an
earlycon which can matched either on the command line or by devicetree.
EARLYCON_DECLARE() is semantically unchanged; it declares an earlycon
which is matched by command line only. Remove redundant instances of
EARLYCON_DECLARE().
This enables all earlycons to properly initialize struct console
with the appropriate name and index, which improves diagnostics and
enables direct earlycon-to-console handoff.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
include/asm-generic/pci-bridge.h is now empty, so remove every #include of
it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com> (arm64)
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
Pull IRQ fixes from Ingo Molnar:
"Mostly irqchip driver fixes, but also an irq core crash fix and a
build fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mxs: Add missing set_handle_irq()
irqchip/atmel-aic: Fix wrong bit operation for IRQ priority
irqchip/gic-v3-its: Recompute the number of pages on page size change
base: Export platform_msi_domain_[alloc,free]_irqs
of: MSI: Simplify irqdomain lookup
irqdomain: Allow domain lookup with DOMAIN_BUS_WIRED token
irqchip: Fix dependencies for archs w/o HAS_IOMEM
irqchip/s3c24xx: Mark init_eint as __maybe_unused
genirq: Validate action before dereferencing it in handle_irq_event_percpu()
Some phy nodes list a compatible value indicating the PHY make/model.
This is never used to match the device to the driver. However it does
confuse the code to separate a PHY from a generic MDIO device like a
switch. Generic MDIO devices must have a compatible value, PHYs can
list clause 22 or 45, but nothing else.
Issue a warning if we find a compatible value known on the whitelist,
and say it is a PHY.
Fixes: a9049e0c51 ("mdio: Add support for mdio drivers.")
Reported-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_find_device() is used to find the phy device associated with a
device node. It is expected the node is for a PHY device, but in fact
it could of been probed as a generic MDIO device. Ensure the device is
a PHY before returning it.
Fixes: a9049e0c51 ("mdio: Add support for mdio drivers.")
Reported-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, when trying to associate a device with its MSI domain,
we first lookup the domain using a MSI token, and if this
doesn't return anything useful, we pick up any domain matching
the same node.
This logic is broken for two reasons:
1) Only the generic MSI code (PCI or platform) sets this token
to PCI/MSI or platform MSI. So we're guaranteed that if there
is something to be found, we will find it with the first call.
2) If we have a convoluted situation where:
- a single node implements both wired and MSI interrupts
- MSI support for that HW hasn't been compiled in
we'll end up using the wired domain for MSIs anyway, and things
break badly.
So let's just remove __of_get_msi_domain, and replace it by a direct
call to irq_find_matching_host, because that's what we really want.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1453816347-32720-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Rework and export the changeset API to make it available to users
other than DT overlays
- ARM secure devices binding
- OCTEON USB binding
- Clean-up of various SRAM binding docs
- Various other binding doc updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LW4w
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- Rework and export the changeset API to make it available to users
other than DT overlays
- ARM secure devices binding
- OCTEON USB binding
- Clean-up of various SRAM binding docs
- Various other binding doc updates
* tag 'devicetree-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (21 commits)
drivers/of: Export OF changeset functions
Fix documentation for adp1653 DT
ARM: psci: Fix indentation in DT bindings
of/platform: export of_default_bus_match_table
of/unittest: Show broken behaviour in the platform bus
of: fix declaration of of_io_request_and_map
of/address: replace printk(KERN_ERR ...) with pr_err(...)
of/irq: optimize device node matching loop in of_irq_init()
dt-bindings: tda998x: Document the required 'port' node.
net/macb: bindings doc: Merge cdns-emac to macb
dt-bindings: Misc fix for the ATH79 DDR controllers
dt-bindings: Misc fix for the ATH79 MISC interrupt controllers
Documentation: dt: Add bindings for Secure-only devices
dt-bindings: ARM: add arm,cortex-a72 compatible string
ASoC: Atmel: ClassD: add GCK's parent clock in DT binding
DT: add Olimex to vendor prefixes
Documentation: fsl-quadspi: Add fsl,ls1021-qspi compatible string
Documentation/devicetree: document OCTEON USB bindings
usb: misc: usb3503: Describe better how to bind clock to the hub
dt-bindings: Consolidate SRAM bindings from all vendors
...
The PowerNV PCI hotplug driver is going to use the OF changeset
to manage the changed device sub-tree. This exports those OF
changeset functions for that.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Rob Herring <robh@kernel.org>
It used to be that mdio->irq was a pointer but after e7f4dc3536
('mdio: Move allocation of interrupts into core') it's an array inside
the mdio struct so it can never be NULL.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers
are PHY drivers. Add support for generic MDIO drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon support devices other than phys on the mdio bus. Look at
a child's compatibility string to determine if it is a phy, before
registering a phy device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, drivers/bus/uniphier-system-bus.c is kept from being a
module due to the unresolved reference to of_default_bus_match_table.
Refer to commit 326ea45aa8 ("bus: uniphier: allow only built-in
driver").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a single resource to the test bus device to exercise the platform
bus code a little more. This isn't strictly a devicetree test, but it is
a corner case that the devicetree runs into. Until we've got platform
device unittests, it can live here. It doesn't need to be an explicit
text because the kernel will oops when it is wrong.
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
[wsa: added the comment provided by Grant, rebased, and tested]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Rob Herring <robh@kernel.org>
A trivial change suggested by checkpatch.pl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Currently, of_irq_init() iterates over interrupt controller nodes
with for_each_matching_node(), and then gets each init function with
of_match_node() later.
This routine can be optimized with for_each_matching_node_and_match().
It allows to get the interrupt controller node and its init function
at the same time, saving __of_match_node() callings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
of_irq_find_parent was made static since it had no users outside of
of_irq.c. Export it again since we are going to use it again.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
[robh: move of_irq_find_parent to correct ifdef section]
Signed-off-by: Rob Herring <robh@kernel.org>
__unflatten_device_tree() calls unflatten_dt_node(), which declares
a static variable. It is therefore not reentrant.
One of the callers of __unflatten_device_tree(), unflatten_device_tree(),
is only called once during early initialization and does not need to be
protected. The other caller, of_fdt_unflatten_tree(), can be called at
any time, possibly multiple times in parallel. This can happen, for
example, if multiple devicetree overlays have to be loaded and installed.
Without this protection, errors such as the following may be seen.
kernel: End of tree marker overwritten: e6a3a458
kernel: find_target_node:
Failed to find target-indirect node at /fragment@0
kernel: __of_overlay_create: of_build_overlay_info() failed for tree@/
Add a mutex to of_fdt_unflatten_tree() to make the call reentrant.
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Rob Herring <robh@kernel.org>
Remove the "not" before "cannot".
I am fixing the comment block style while I am here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Frank Rowand