The memory allocated for the slow path table flow group input structure
was not freed upon successful return, fix that.
Fixes: 1967ce6ea5 ("net/mlx5: E-Switch, Refactor fast path FDB table creation in switchdev mode")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Minimal stride size is 16.
Hence, the number of strides in a fragment (of PAGE_SIZE)
is <= PAGE_SIZE / 16 <= 4K.
u16 is sufficient to represent this.
Fixes: d7037ad73d ("net/mlx5: Fix QP fragmented buffer allocation")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Minimal stride size is 16.
Hence, the number of strides in a fragment (of PAGE_SIZE)
is <= PAGE_SIZE / 16 <= 4K.
u16 is sufficient to represent this.
Fixes: 388ca8be00 ("IB/mlx5: Implement fragmented completion queue (CQ)")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When initializing the device (procedure init_one), the driver
calls mlx5_pci_init to perform pci initialization. As part of this
initialization, mlx5_pci_init creates a debugfs directory.
If this creation fails, init_one aborts, returning failure to
the caller (which is the probe method caller).
The main reason for such a failure to occur is if the debugfs
directory already exists. This can happen if the last time
mlx5_pci_close was called, debugfs_remove (silently) failed due
to the debugfs directory not being empty.
Guarantee that such a debugfs_remove failure will not occur by
instead calling debugfs_remove_recursive in procedure mlx5_pci_close.
Fixes: 59211bd3b6 ("net/mlx5: Split the load/unload flow into hardware and software flows")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the mlx5 health mechanism detects a problem while the driver
is in the middle of init_one or remove_one, the driver needs to prevent
the health mechanism from scheduling future work; if future work
is scheduled, there is a problem with use-after-free: the system WQ
tries to run the work item (which has been freed) at the scheduled
future time.
Prevent this by disabling work item scheduling in the health mechanism
when the driver is in the middle of init_one() or remove_one().
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With performance optimization the spi transfer and messages of basic
register operations like qcaspi_read_register moved into the private
driver structure. But they weren't protected against mutual access
(e.g. between driver kthread and ethtool). So dumping the QCA7000
registers via ethtool during network traffic could make spi_sync
hang forever, because the completion in spi_message is overwritten.
So revert the optimization completely.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA700")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA allocated memory is lost in be_cmd_get_profile_config() when we
call it with non-NULL port_res parameter.
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC-aware mode was recently enabled by mlxsw on Spectrum switches in
commit 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw
ports"). Unfortunately, testing has shown that the fix is incomplete and
in the presented form actually makes the problem even worse, because any
amount of MC traffic causes UC disruption.
The reason for this is that currently, mlxsw configures the MC-specific
TCs (8..15) to map to pool 0. It also configures a maximum buffer size
of 0, but for MC traffic that maximum is disregarded and not part of the
quota. Therefore MC traffic is always admitted to the egress buffer.
Fix the configuration by directing the MC TCs into pool 15, which is
dedicated to MC traffic and recognized as such by the silicon.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all SFPs implement the registers containing sensor limits and
alarms. Luckily, there is a bit indicating if they are implemented or
not. Add checking for this bit, when deciding if the hwmon attributes
should be visible.
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the formula for calculating the RQ page remainder,
which should be in byte granularity. The result will be
non-zero only for RQs smaller than PAGE_SIZE, as an RQ size
is a power of 2.
Divide this by the SQ stride (MLX5_SEND_WQE_BB) to get the
SQ offset in strides granularity.
Fixes: d7037ad73d ("net/mlx5: Fix QP fragmented buffer allocation")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAluNJXcACgkQB8qZga/f
l8Qvfw//dBwlhMII862Evk4M8OzhdHfkJ4Kp/d2C476whbEySU/jRIIeetmVpXYV
5cfStTxBpGkwMj5PXy3DaA2PO++L5qaApDJfHc8DNWNmvt9rRRJul1zP05HjZRxW
G7aFCFRWVK0dlmVP9GC/b20KyUvz4OpklBnxylkIrx0FCkw5bAHs1SsjGZCg/6Tm
008DAhFz3Ds6hNLxwricvrk5oQ6eC1cDfDd4Rtk3jCYQ4t7KFn5gFoKzKldfLdWe
TFTpVQ26XAGzn9QVXzAiXN4ZNpUpZrFXosC7cn5Ugiyic4YtnHxS2wVDuL3vs1cL
J2hoW6wjEBg+U6vmHMcijo1lnQwW7ueYUDWLJPNIXHA6A7sGyA6z6D7vbbvHfoG6
L681BrYmTmKkXXquu5+r85/9WgP2cmzbRpoIxTQl3sU2Liw2k5IJ9ryLLyul+8z7
spnDPOY7h4c0JrAvhjHkrKIbbW4FKYunxZJ8dn9eyAzOd/58iKoXzu4yAggwm+0V
DtZiu0gSr52sKrh1vqEyfhrPFCN1Mc19DRsJBtabUfVEveQTwToCkbZ5s1sLqSId
m30XUjjYOiRk7MZnncar0lE4//eJ6bnL3Wie3UTmO3xsMwlgKQPqjI4TprNogUCk
R2dVeGmhm3HSriRHKJL3/D8uzw5mMBI3Kicw9tFSSyVjtJgxvpg=
=lLBA
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are quite a large number of fixes, notably:
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number
of MSIX vectors used by RDMA. There is one code path in open that needs
to check the true max_cp_rings including any used by RDMA. This code
is now checking for the reduced max_cp_rings which will fail when the
number of cp rings is very small.
To fix this in a clean way, we don't adjust max_cp_rings anymore.
Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the
reduced max_cp_rings when appropriate.
Fixes: ec86f14ea5 ("bnxt_en: Add ULP calls to stop and restart IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused bnxt_subtract_ulp_resources(). Change
bnxt_get_max_func_irqs() to static since it is only locally used.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver detects that resources have changed during open, it
should reset the rx and tx rings to 0. This will properly setup the
init sequence to initialize the default rings again. We also need
to signal the RDMA driver to stop and clear its interrupts. We then
call the RoCE driver to restart if a new set of default rings is
successfully reserved.
Fixes: 25e1acd6b9 ("bnxt_en: Notify firmware about IF state changes.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__emac_calc_base_mr1 was used instead of __emac4_calc_base_mr1
by copy-paste mistake for emac4syn.
Fixes: 45d6e54550 ("net/ibm/emac: add 8192 rx/tx fifo size")
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This card identifies itself as:
Ethernet controller [0200]: NCube Device [10ff:8168] (rev 06)
Subsystem: TP-LINK Technologies Co., Ltd. Device [7470:3468]
Adding a new entry to rtl8169_pci_tbl makes the card work.
Link: http://launchpad.net/bugs/1788730
Signed-off-by: Anthony Wong <anthony.wong@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel module may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.16 are:
[FUNC] usleep_range
drivers/net/ethernet/cadence/macb_main.c, 648:
usleep_range in macb_halt_tx
drivers/net/ethernet/cadence/macb_main.c, 730:
macb_halt_tx in macb_tx_error_task
drivers/net/ethernet/cadence/macb_main.c, 721:
_raw_spin_lock_irqsave in macb_tx_error_task
To fix this bug, usleep_range() is replaced with udelay().
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw-phy-sel device is not a child of the cpsw interconnect target
module. It lives in the system control module.
Let's fix this issue by trying to use cpsw-phy-sel phandle first if it
exists and if not fall back to current usage of trying to find the
cpsw-phy-sel child. That way the phy sel driver can be a child of the
system control module where it belongs in the device tree.
Without this fix, we cannot have a proper interconnect target module
hierarchy in device tree for things like genpd.
Note that deferred probe is mostly not supported by cpsw and this patch
does not attempt to fix that. In case deferred probe support is needed,
this could be added to cpsw_slave_open() and phy_connect() so they start
handling and returning errors.
For documenting it, looks like the cpsw-phy-sel is used for all cpsw device
tree nodes. It's missing the related binding documentation, so let's also
update the binding documentation accordingly.
Cc: devicetree@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the return codes of these functions and halt reset
in case of failure. The driver will remain in a dormant state
until the next reset event, when device initialization will be
re-attempted.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the race between netvsc_probe() and
rndis_set_subchannel(), which can cause a deadlock.
These are the related 3 paths which show the deadlock:
path #1:
Workqueue: hv_vmbus_con vmbus_onmessage_work [hv_vmbus]
Call Trace:
schedule
schedule_preempt_disabled
__mutex_lock
__device_attach
bus_probe_device
device_add
vmbus_device_register
vmbus_onoffer
vmbus_onmessage_work
process_one_work
worker_thread
kthread
ret_from_fork
path #2:
schedule
schedule_preempt_disabled
__mutex_lock
netvsc_probe
vmbus_probe
really_probe
__driver_attach
bus_for_each_dev
driver_attach_async
async_run_entry_fn
process_one_work
worker_thread
kthread
ret_from_fork
path #3:
Workqueue: events netvsc_subchan_work [hv_netvsc]
Call Trace:
schedule
rndis_set_subchannel
netvsc_subchan_work
process_one_work
worker_thread
kthread
ret_from_fork
Before path #1 finishes, path #2 can start to run, because just before
the "bus_probe_device(dev);" in device_add() in path #1, there is a line
"object_uevent(&dev->kobj, KOBJ_ADD);", so systemd-udevd can
immediately try to load hv_netvsc and hence path #2 can start to run.
Next, path #2 offloads the subchannal's initialization to a workqueue,
i.e. path #3, so we can end up in a deadlock situation like this:
Path #2 gets the device lock, and is trying to get the rtnl lock;
Path #3 gets the rtnl lock and is waiting for all the subchannel messages
to be processed;
Path #1 is trying to get the device lock, but since #2 is not releasing
the device lock, path #1 has to sleep; since the VMBus messages are
processed one by one, this means the sub-channel messages can't be
procedded, so #3 has to sleep with the rtnl lock held, and finally #2
has to sleep... Now all the 3 paths are sleeping and we hit the deadlock.
With the patch, we can make sure #2 gets both the device lock and the
rtnl lock together, gets its job done, and releases the locks, so #1
and #3 will not be blocked for ever.
Fixes: 8195b1396e ("hv_netvsc: fix deadlock on hotplug")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid leaking a running timer we need to wait for the
posted reconfigs after netdev is unregistered. In common
case the process of deinitializing the device will perform
synchronous reconfigs which wait for posted requests, but
especially with VXLAN ports being actively added and removed
there can be a race condition leaving a timer running after
adapter structure is freed leading to a crash.
Add an explicit flush after deregistering and for a good
measure a warning to check if timer is running just before
structures are freed.
Fixes: 3d780b926a ("nfp: add async reconfiguration mechanism")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without a valid of_node in struct device we can't find the mvpp2 port
device by its DT node. Specifically, this breaks
of_find_net_device_by_node().
For example, the Armada 8040 based Clearfog GT-8K uses Marvell 88E6141
switch connected to the &cp1_eth2 port:
&cp1_mdio {
...
switch0: switch0@4 {
compatible = "marvell,mv88e6085";
...
ports {
...
port@5 {
reg = <5>;
label = "cpu";
ethernet = <&cp1_eth2>;
};
};
};
};
Without this patch, dsa_register_switch() returns -EPROBE_DEFER because
of_find_net_device_by_node() can't find the device_node of the &cp1_eth2
device.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the fixed PHY with GENET (e.g. MOCA) the PHY link
status can be determined from the internal link status captured
by the MAC. This allows the PHY state machine to use the correct
link state with the fixed PHY even if MAC link event interrupts
are missed when the net device is opened.
Fixes: 8d88c6ebb3 ("net: bcmgenet: enable MoCA link state change detection")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Stratix10 SoC is an AARCH64 based platform that shares the same ethernet
controller that is on other SoCFPGA platforms. Build the platform driver.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the R7S9210 which is part of the RZ/A2 series.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are packets in hardware when changing the speed
or duplex, it may cause hardware hang up.
This patch adds netif_carrier_off before change speed and
duplex in ethtool_ops.set_link_ksettings, and adds
netif_carrier_on after complete the change.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are packets in hardware when changing the speed
or duplex, it may cause hardware hang up.
This patch adds the code for waiting chip to clean the all
pkts(TX & RX) in chip when the driver uses the function named
"adjust link".
This patch cleans the pkts as follows:
1) close rx of chip, close tx of protocol stack.
2) wait rcb, ppe, mac to clean.
3) adjust link
4) open rx of chip, open tx of protocol stack.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have two Ethernet adapters:
r8169 0000:03:01.0 eth0: RTL8169sb/8110sb, 00:14:d1:14:2d:49, XID 10000000, IRQ 18
r8169 0000:01:00.0 eth0: RTL8168e/8111e, 64:66:b3:11:14:5d, XID 2c200000, IRQ 30
And after upgrading from linux 4.15 [1] to linux 4.18+ [2] RTL8169sb failed to
receive any packets. tcpdump shows a lot of checksum mismatch.
[1]: a0f79386a4
[2]: 0519359784 (4.19 merge window opened)
I started bisecting and the found that [3] breaks it. According to [4]:
"For 8110S, 8110SB, and 8110SC series, the initial value of RxConfig
needs to be set after the tx/rx is enabled."
So I moved rtl_init_rxcfg() after enabling tx/rs and now my adapter works
(RTL8168e works too).
[3]: 3559d81e76
[4]: e542a2269f ("r8169: adjust the RxConfig
settings.")
Also drop "rx" from rtl_set_rx_tx_config_registers(), since it does nothing
with it already.
Fixes: 3559d81e76 ("r8169: simplify
rtl_hw_start_8169")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Azat Khuzhin <a3at.mail@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 4ae0169fd1.
This change in the handling of the coalesce timer is causing regression on
(at least) amlogic platforms.
Network will break down very quickly (a few seconds) after starting
a download. This can easily be reproduced using iperf3 for example.
The problem has been reported on the S805, S905, S912 and A113 SoCs
(Realtek and Micrel PHYs) and it is likely impacting all Amlogics
platforms using Gbit ethernet
No problem was seen with the platform using 10/100 only PHYs (GXL internal)
Reverting change brings things back to normal and allows to use network
again until we better understand the problem with the coalesce timer.
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User controls @idx which to be used as index of hwsim_world_regdom_custom.
So, It can be exploited via Spectre-like attack. (speculative execution)
This kind of attack leaks address of hwsim_world_regdom_custom,
It leads an attacker to bypass security mechanism such as KASLR.
So sanitize @idx before using it to prevent attack.
I leveraged strategy [1] to find and exploit this gadget.
[1] https://github.com/jinb-park/linux-exploit/tree/master/exploit-remaining-spectre-gadget/
Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
[johannes: unwrap URL]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make wmm_rule be part of the reg_rule structure. This simplifies the
code a lot at the cost of having bigger memory usage. However in most
cases we have only few reg_rule's and when we do have many like in
iwlwifi we do not save memory as it allocates a separate wmm_rule for
each channel anyway.
This also fixes a bug reported in various places where somewhere the
pointers were corrupted and we ended up doing a null-dereference.
Fixes: 230ebaa189 ("cfg80211: read wmm rules from regulatory database")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[rephrase commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mac80211_hwsim driver intends to say that it supports up to four
STBC receive streams, but instead it ends up saying something undefined.
The IEEE80211_VHT_CAP_RXSTBC_X macros aren't independent bits that can
be ORed together, but values. In this case, _4 is the appropriate one
to use.
Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) ICE, E1000, IGB, IXGBE, and I40E bug fixes from the Intel folks.
2) Better fix for AB-BA deadlock in packet scheduler code, from Cong
Wang.
3) bpf sockmap fixes (zero sized key handling, etc.) from Daniel
Borkmann.
4) Send zero IPID in TCP resets and SYN-RECV state ACKs, to prevent
attackers using it as a side-channel. From Eric Dumazet.
5) Memory leak in mediatek bluetooth driver, from Gustavo A. R. Silva.
6) Hook up rt->dst.input of ipv6 anycast routes properly, from Hangbin
Liu.
7) hns and hns3 bug fixes from Huazhong Tan.
8) Fix RIF leak in mlxsw driver, from Ido Schimmel.
9) iova range check fix in vhost, from Jason Wang.
10) Fix hang in do_tcp_sendpages() with tls, from John Fastabend.
11) More r8152 chips need to disable RX aggregation, from Kai-Heng Feng.
12) Memory exposure in TCA_U32_SEL handling, from Kees Cook.
13) TCP BBR congestion control fixes from Kevin Yang.
14) hv_netvsc, ignore non-PCI devices, from Stephen Hemminger.
15) qed driver fixes from Tomer Tayar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: sched: Fix memory exposure from short TCA_U32_SEL
qed: fix spelling mistake "comparsion" -> "comparison"
vhost: correctly check the iova range when waking virtqueue
qlge: Fix netdev features configuration.
net: macb: do not disable MDIO bus at open/close time
Revert "net: stmmac: fix build failure due to missing COMMON_CLK dependency"
net: macb: Fix regression breaking non-MDIO fixed-link PHYs
mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridge
i40e: fix condition of WARN_ONCE for stat strings
i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled
ixgbe: fix driver behaviour after issuing VFLR
ixgbe: Prevent unsupported configurations with XDP
ixgbe: Replace GFP_ATOMIC with GFP_KERNEL
igb: Replace mdelay() with msleep() in igb_integrated_phy_loopback()
igb: Replace GFP_ATOMIC with GFP_KERNEL in igb_sw_init()
igb: Use an advanced ctx descriptor for launchtime
e1000: ensure to free old tx/rx rings in set_ringparam()
e1000: check on netif_running() before calling e1000_up()
ixgb: use dma_zalloc_coherent instead of allocator/memset
ice: Trivial formatting fixes
...
Trivial fix to spelling mistake in DP_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlge_fix_features() is not supposed to modify hardware or
driver state, rather it is supposed to only fix requested
fetures bits. Currently qlge_fix_features() also goes for
interface down and up unnecessarily if there is not even
any change in features set.
This patch changes/fixes following -
1) Move reload of interface or device re-config from
qlge_fix_features() to qlge_set_features().
2) Reload of interface in qlge_set_features() only if
relevant feature bit (NETIF_F_HW_VLAN_CTAG_RX) is changed.
3) Get rid of qlge_fix_features() since driver is not really
required to fix any features bit.
Signed-off-by: Manish <manish.chopra@cavium.com>
Reviewed-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_reset_hw() is called from macb_close() and indirectly from
macb_open(). macb_reset_hw() zeroes the NCR register, including the MPE
(Management Port Enable) bit.
This will prevent accessing any other PHYs for other Ethernet MACs on
the MDIO bus, which remains registered at macb_reset_hw() time, until
macb_init_hw() is called from macb_open() which sets the MPE bit again.
I.e. currently the MDIO bus has a short disruption at open time and is
disabled at close time until the interface is opened again.
Fix that by only touching the RE and TE bits when enabling and disabling
RX/TX.
v2: Make macb_init_hw() NCR write a single statement.
Fixes: 6c36a70744 ("macb: Use generic PHY layer")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bde4975310.
All legacy clock implementations now implement clk_set_rate() (Some
implementations may be dummies, though).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arnd.de>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 739de9a156 ("net: macb: Reorganize macb_mii bringup") broke
initializing macb on the EVB-KSZ9477 eval board.
There, of_mdiobus_register was called even for the fixed-link representing
the RGMII-link to the switch with the result that the driver attempts to
enumerate PHYs on a non-existent MDIO bus:
libphy: MACB_mii_bus: probed
mdio_bus f0028000.ethernet-ffffffff: fixed-link has invalid PHY address
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 0
[snip]
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 31
The "MDIO" bus registration succeeds regardless, having claimed the reset GPIO,
and calling of_phy_register_fixed_link later on fails because it tries
to claim the same GPIO:
macb f0028000.ethernet: broken fixed-link specification
Fix this by registering the fixed-link before calling mdiobus_register.
Fixes: 739de9a156 ("net: macb: Reorganize macb_mii bringup")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bridge device is removed, the VLANs are flushed from each
configured port. This causes the ports to decrement the reference count
on the associated FIDs (filtering identifier). If the reference count of
a FID is 1 and it has a RIF (router interface), then this RIF is
destroyed.
However, if no port is member in the VLAN for which a RIF exists, then
the RIF will continue to exist after the removal of the bridge. To
reproduce:
# ip link add name br0 type bridge vlan_filtering 1
# ip link set dev swp1 master br0
# ip link add link br0 name br0.10 type vlan id 10
# ip address add 192.0.2.0/24 dev br0.10
# ip link del dev br0
The RIF associated with br0.10 continues to exist.
Fix this by iterating over all the bridge device uppers when it is
destroyed and take care of destroying their RIFs.
Fixes: 99f44bb352 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9b10df596b ("i40e: use WARN_ONCE to replace the commented
BUG_ON size check") introduced a warning check to make sure
that the size of the stat strings was always the expected value. This
code accidentally inverted the check of the data pointer. Fix this so
that we accurately count the size of the stats we copied in.
This fixes an erroneous WARN kernel splat that occurs when requesting
ethtool statistics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Tested-by: Mauro S M Rodrigues <maurosr@linux.vnet.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If interface is connected to switch port configured for DCB there are
TX timeouts when bringing up interface. Problem started appearing after
adding in i40e driver code mqprio hardware offload mode. In function
i40e_vsi_configure_bw_alloc was added resetting BW rate which should
be executing when mqprio qdisc is removed but was also when there was
no mqprio qdisc added and DCB was enabled. In this patch was added
additional check for DCB flag so now when DCB is enabled the correct
DCB configs from before mqprio patch are restored.
Signed-off-by: Martyna Szapar <martyna.szapar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since VFLR doesn't clear VFMBMEM (VF Mailbox Memory)
and is not re-enabling queues correctly we should fix
this behavior.
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These changes address comments by Jakub Kicinski on
commit 38b7e7f8ae ("ixgbe: Do not allow LRO or MTU change with XDP").
Change the MTU check with XDP to allow any supported value and only
reject those outside of the range as opposed to rejecting any change
when XDP is active. In situations where MTU size is not supported,
return -EINVAL instead of -EPERM.
Add checks when enabling SRIOV, DCB, or adding L2FW offloaded device
as they are not supported with XDP.
CC: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_fcoe_ddp_setup(), ixgbe_setup_fcoe_ddp_resources() and
ixgbe_sw_init() are never called in atomic context.
They call kmalloc(), dma_pool_alloc() and kzalloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb_integrated_phy_loopback() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb_sw_init() is never called in atomic context.
It calls kzalloc() and kcalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On i210, Launchtime (TxTime) requires the usage of an "Advanced
Transmit Context Descriptor" for retrieving the timestamp of a packet.
The igb driver correctly builds such descriptor on the segmentation
flow (i.e. igb_tso()) or on the checksum one (i.e. igb_tx_csum()), but the
feature is broken for AF_PACKET if the IGB_TX_FLAGS_VLAN is not set,
which happens due to an early return on igb_tx_csum().
This flag is only set by the kernel when a VLAN interface is used,
thus we can't just rely on it. Here we are fixing this issue by checking
if launchtime is enabled for the current tx_ring before performing the
early return.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In 'e1000_set_ringparam()', the tx_ring and rx_ring are updated with new value
and the old tx/rx rings are freed only when the device is up. There are resource
leaks on old tx/rx rings when the device is not up. This bug is reported by COD,
a tool for testing kernel module binaries I am building.
This patch fixes the bug by always calling 'kfree()' on old tx/rx rings in
'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the device is not up, the call to 'e1000_up()' from the error handling path
of 'e1000_set_ringparam()' causes a kernel oops with a null-pointer
dereference. The null-pointer dereference is triggered in function
'e1000_alloc_rx_buffers()' at line 'buffer_info = &rx_ring->buffer_info[i]'.
This bug was reported by COD, a tool for testing kernel module binaries I am
building. This bug was also detected by KFI from Dr. Kai Cong.
This patch fixes the bug by checking on 'netif_running()' before calling
'e1000_up()' in 'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Raed Salem