The gic_set_type() function included writes to the MIPS GIC polarity,
trigger & dual-trigger registers in each case of a switch statement
determining the IRQs type. This is all well & good when we only have a
single cluster & thus a single GIC whose register we want to update. It
will lead to significant duplication once we have multi-cluster support
& multiple GICs to update.
Refactor this such that we determine values for the polarity, trigger &
dual-trigger registers and then have a single set of register writes
following the switch statement. This will allow us to write the same
values to each GIC in a multi-cluster system in a later patch, rather
than needing to duplicate more register writes in each case.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Following the past few patches nothing uses the gic_vpes variable any
longer. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reserving a number of IPIs based upon the number of VPs reported by the
GIC makes little sense for a few reasons:
- The kernel may have been configured with NR_CPUS less than the number
of VPs in the cluster, in which case using gic_vpes causes us to
reserve more interrupts for IPIs than we will possibly use.
- If a kernel is configured without support for multi-threading & runs
on a system with multi-threading & multiple VPs per core then we'll
similarly reserve more interrupts for IPIs than we will possibly use.
- In systems with multiple clusters the GIC can only provide us with
the number of VPs in its cluster, not across all clusters. In this
case we'll reserve fewer interrupts for IPIs than we need.
Fix these issues by using num_possible_cpus() instead, which in all
cases is actually indicative of how many IPIs we may need.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Rather than configuring EIC mode for all CPUs during boot, configure it
locally on each when they come online. This will become important with
multi-cluster support, since clusters may be powered on & off (for
example via hotplug) and would lose the EIC configuration when powered
off.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We currently walk through the range 0..gic_vpes-1, expecting these
values all to be valid Linux CPU numbers to provide to mips_cm_vp_id(),
and masking all routable local interrupts during boot. This approach has
a few drawbacks:
- In multi-cluster systems we won't have access to all CPU's GIC local
registers when the driver is probed, since clusters (and their GICs)
may be powered down at this point & only brought online later.
- In multi-cluster systems we may power down clusters at runtime, for
example if we offline all CPUs within it via hotplug, and the
cluster's GIC may lose state. We therefore need to reinitialise it
when powering back up, which this approach does not take into
account.
- The range 0..gic_vpes-1 may not all be valid Linux CPU numbers, for
example if we run a kernel configured to support fewer CPUs than the
system it is running on actually has. In this case we'll get garbage
values from mips_cm_vp_id() as we read past the end of the cpu_data
array.
Fix this and simplify the code somewhat by writing an all-bits-set
value to the VP-local reset mask register when a CPU is brought online,
before any local interrupts are configured for it. This removes the need
for us to access all CPUs during driver probe, removing all of the
problems described above.
In the name of simplicity we drop the checks for routability of
interrupts and simply clear the mask bits for all interrupts. Bits for
non-routable local interrupts will have no effect so there's no point
performing extra work to avoid modifying them.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The gic_all_vpes_local_irq_controller chip currently attempts to operate
on all CPUs/VPs in the system when masking or unmasking an interrupt.
This has a few drawbacks:
- In multi-cluster systems we may not always have access to all CPUs in
the system. When all CPUs in a cluster are powered down that
cluster's GIC may also power down, in which case we cannot configure
its state.
- Relatedly, if we power down a cluster after having configured
interrupts for CPUs within it then the cluster's GIC may lose state &
we need to reconfigure it. The current approach doesn't take this
into account.
- It's wasteful if we run Linux on fewer VPs than are present in the
system. For example if we run a uniprocessor kernel on CPU0 of a
system with 16 CPUs then there's no point in us configuring CPUs
1-15.
- The implementation is also lacking in that it expects the range
0..gic_vpes-1 to represent valid Linux CPU numbers which may not
always be the case - for example if we run on a system with more VPs
than the kernel is configured to support.
Fix all of these issues by only configuring the affected interrupts for
CPUs which are online at the time, and recording the configuration in a
new struct gic_all_vpes_chip_data for later use by CPUs being brought
online. We register a CPU hotplug state (reusing
CPUHP_AP_IRQ_GIC_STARTING which the ARM GIC driver uses, and which seems
suitably generic for reuse with the MIPS GIC) and execute
irq_cpu_online() in order to configure the interrupts on the newly
onlined CPU.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The gic_local_irq_domain_map() function has only one callsite in
gic_irq_domain_map(), and the split between the two functions makes it
unclear that they duplicate calculations & checks.
Inline gic_local_irq_domain_map() into gic_irq_domain_map() in order to
clean this up. Doing this makes the following small issues obvious, and
the patch tidies them up:
- Both functions used GIC_HWIRQ_TO_LOCAL() to convert a hwirq number to
a local IRQ number. We now only do this once. Although the compiler
ought to have optimised this away before anyway, the change leaves us
with less duplicate code.
- gic_local_irq_domain_map() had a check for invalid local interrupt
numbers (intr > GIC_LOCAL_INT_FDC). This condition can never occur
because any hwirq higher than those used for local interrupts is a
shared interrupt, which gic_irq_domain_map() already handles
separately. We therefore remove this check.
- The decision of whether to map the interrupt to gic_cpu_pin or
timer_cpu_pin can be handled within the existing switch statement in
gic_irq_domain_map(), shortening the code a little.
The change additionally prepares us nicely for the following patch of
the series which would otherwise need to duplicate the check for whether
a local interrupt should be percpu_devid or just percpu (ie. the switch
statement from gic_irq_domain_map()) in gic_local_irq_domain_map().
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Meson8 uses the same GPIO interrupt controller IP block as the other
Meson SoCs. A total of 134 pins can be spied on, which is the sum of:
- 22 pins on bank GPIOX
- 17 pins on bank GPIOY
- 30 pins on bank GPIODV
- 10 pins on bank GPIOH
- 15 pins on bank GPIOZ
- 7 pins on bank CARD
- 19 pins on bank BOOT
- 14 pins in the AO domain
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is a lot of broken firmware out there that don't really
expose the information the kernel requires when it comes with dealing
with GICv2:
(1) Firmware that only describes the first 4kB of GICv2
(2) Firmware that describe 128kB of CPU interface, while
the usable portion of the address space is between
60 and 68kB
So far, we only deal with (2). But we have platforms exhibiting
behaviour (1), resulting in two sub-cases:
(a) The GIC is occupying 8kB, as required by the GICv2 architecture
(b) It is actually spread 128kB, and this is likely to be a version
of (2)
This patch tries to work around both (a) and (b) by poking at
the outside of the described memory region, and try to work out
what is actually there. This is of course unsafe, and should
only be enabled if there is no way to otherwise fix the DT provided
by the firmware (we provide a "irqchip.gicv2_force_probe" option
to that effect).
Note that for the time being, we restrict ourselves to GICv2
implementations provided by ARM, since there I have no knowledge
of an alternative implementations. This could be relaxed if such
an implementation comes to light on a broken platform.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, we require the hypervisor to update the VLPI properties
once the the VLPI mapping has been established. While this
makes it easy for the ITS driver, it creates a window where
an incoming interrupt can be delivered with an unknown set
of properties. Not very nice.
Instead, let's add a "properties" field to the mapping structure,
and use that to configure the VLPI before it actually gets mapped.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver fails to compile with CONFIG_COMPILE_TEST=y on x86:
irq-meson-gpio.c: In function ‘meson_gpio_irq_parse_dt’:
irq-meson-gpio.c:343:8: error: implicit declaration of function
‘of_property_read_variable_u32_array’
ret = of_property_read_variable_u32_array(node,
Adding COMPILE_TEST to a driver requires at least compile testing it for
x86....
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
please pull the following:
- Danilo removes the clock provider driver stubs which are no longer needed
now that we have a proper CPRMAN clock provider driver
- Stefan moves the SMP startup code for BCM2836 from the interrupt controller
driver down to where it belongs in the architecture code, this was requested
by Marc Zyngier before comitting any fixes to that code
- Phil provides a fix for a future Raspberry Pi firmware which will make the
secondary cores wait for an event and therefore requires the CPU onlining
other cores to send such event (along with the appropriate barrier)
- Florian fixes the BRCMSTB UART debug stub to work correctly when using an
ARM BE8 kernel since there were some missing register read swapping needed
-----BEGIN PGP SIGNATURE-----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=h/36
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.15/soc' of http://github.com/Broadcom/stblinux into next/soc
Pull "Broadcom soc changes for 4.15 (part 1)" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC/Kconfig changes for 4.15
please pull the following:
- Danilo removes the clock provider driver stubs which are no longer needed
now that we have a proper CPRMAN clock provider driver
- Stefan moves the SMP startup code for BCM2836 from the interrupt controller
driver down to where it belongs in the architecture code, this was requested
by Marc Zyngier before comitting any fixes to that code
- Phil provides a fix for a future Raspberry Pi firmware which will make the
secondary cores wait for an event and therefore requires the CPU onlining
other cores to send such event (along with the appropriate barrier)
- Florian fixes the BRCMSTB UART debug stub to work correctly when using an
ARM BE8 kernel since there were some missing register read swapping needed
* tag 'arm-soc/for-4.15/soc' of http://github.com/Broadcom/stblinux:
ARM: brcmstb: Add appropriate ARM_BE8() macros for swapping
ARM: bcm2836: Send event when onlining other cores
irqchip: bcm2836: Move SMP startup code to arch/arm (v2)
clk: bcm2835: remove remains from stub clk driver
In case of error, the function of_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test..
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add support for the interrupt gpio controller found on Amlogic's meson
SoC family.
This controller is a separate controller from the gpio controller. It is
able to spy on the SoC pad. It is essentially a 256 to 8 router with a
filtering block to select level or edge and polarity. The number of actual
mappable inputs depends on the SoC.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When setting the affinity of a VPE (either because we map or move
it), make sure the effective affinity is correctly reported back
to the core kernel.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Sending VINVALL to all ITSs is completely pointless, as all
we're trying to achieve is to tell the redistributor that
the property table for this VPE should be invalidated.
Let's issue the command on the first valid ITS and be done with it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, we map all VPEs on all ITSs. While this is not wrong,
this is quite a big hammer, as moving a VPE around requires
all ITSs to be synchronized. Needles to say, this is an
expensive proposition.
Instead, let's switch to a mode where we issue VMAPP commands
only on ITSs that are actually involved in reporting interrupts
to the given VM.
For that purpose, we refcount the number of interrupts are are
mapped for this VM on each ITS, performing the map/unmap
operations as required. It then allows us to use this refcount
to only issue VMOVP to the ITSs that need to know about this
VM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently, its_send_vmapp operates on all ITSs. As we're about
to try and limit the amount of commands we send to ITSs that are
not involved in dealing with a given VM, let's redefine that
primitive so that it takes a target ITS as a parameter.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently, its_send_vinvall operates on all ITSs. As we're about
to try and limit the amount of commands we send to ITSs that are
not involved in dealing with a given VM, let's redefine that
primitive so that it takes a target ITS as a parameter.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're about to make use of the maximum number of ITSs in
a GICv4 system, let's make this value global (and rename it to
GICv4_ITS_LIST_MAX).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
At boot time, we enumerate all the GICv4-capable ITSs, and build
a mask of the available ITSs. Take this opportunity to store
the ITS number in the its_node structure so that we can use it
at a later time.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ITSes on the Hip07 (as present in the Huawei D05) are broken when
it comes to addressing the redistributors, and need to be explicitely
told to address the VLPI page instead of the redistributor base address.
So let's add yet another quirk, fixing up the target address
in the command stream.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to be able to issue command variants depending on
how broken an ITS is, let's pass the its pointer to all
command building primitives.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the ITS stops processing commands, we're pretty much toasted
as we cannot update the configuration anymore (and we're not
even sure that the ITS still translates interrups).
If that happens, let's dump some basic information about the
state of affairs before moving on.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Socionext Synquacer SoC's implementation of GICv3 has a so-called
'pre-ITS', which maps 32-bit writes targeted at a separate window of
size '4 << device_id_bits' onto writes to GITS_TRANSLATER with device
ID taken from bits [device_id_bits + 1:2] of the window offset.
Writes that target GITS_TRANSLATER directly are reported as originating
from device ID #0.
So add a workaround for this. Given that this breaks isolation, clear
the IRQ_DOMAIN_FLAG_MSI_REMAP flag as well.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As it turns out, the IIDR is not sufficient to distinguish between GICv3
implementations when it comes to enabling quirks. So update the prototype
of the init() hook to return a bool, and interpret a 'false' return value
as no match, in which case the 'enabling workaround' log message should
not be printed.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Before adding another SoC whose device ID space deviates from the
value presented in the GIC ID registers, let's slightly refactor
the code so that the ID registers are probed before that quirks
handling executes. This allows us to move the device ID override
into the quirk handler itself.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A new feature Range Selector (RS) has been added to GIC specification
in order to support more than 16 CPUs at affinity level 0. New fields
are introduced in SGI system registers (ICC_SGI0R_EL1, ICC_SGI1R_EL1
and ICC_ASGI1R_EL1) to relax an artificial limit of 16 at level 0.
- A new RSS field in ICC_CTLR_EL3, ICC_CTLR_EL1 and ICV_CTLR_EL1:
[18] - Range Selector Support (RSS)
0b0 = Targeted SGIs with affinity level 0 values of 0-15 are supported.
0b1 = Targeted SGIs with affinity level 0 values of 0-255 are supported.
- A new RS field in ICC_SGI0R_EL1, ICC_SGI1R_EL1 and ICC_ASGI1R_EL1:
[47:44] - RangeSelector (RS) which group of 16 TargetList[n] field
TargetList[n] represents aff0 value ((RS*16)+n)
When ICC_CTLR_EL3.RSS==0 or ICC_CTLR_EL1.RSS==0, RS is RES0.
- A new RSS field in GICD_TYPER:
[26] - Range Selector Support (RSS)
0b0 = Targeted SGIs with affinity level 0 values of 0-15 are supported.
0b1 = Targeted SGIs with affinity level 0 values of 0-255 are supported.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the initialization of the generic irq chip for the BCM7271 L2
interrupt controller. This controller only supports level
interrupts and uses the "brcm,bcm7271-l2-intc" compatibility
string.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Added register block offsets to the brcmstb_l2_intc_data structure
for the status and mask registers to support reading the active
interupts in an abstracted way. It seems like an irq_chip method
should have been provided for this, but it's not there yet.
Abstracted the implementation of the handler, suspend, and resume
functions to not use any hard coded register offsets.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Saving the generic chip pointer in the brcmstb_l2_intc_data prevents
the need to call irq_get_domain_generic_chip(). Also don't need to
save parent_irq and base there since local variables in the
brcmstb_l2_intc_of_init() function are just as good.
The handle_edge_irq flow or chained_irq_enter takes care of the
acknowledgment of the interrupt so it is redundant to clear it in
brcmstb_l2_intc_irq_handle().
irq_linear_revmap() is a fast path equivalent of irq_find_mapping()
that is appropriate to use for domain controllers of this type.
Defining irq_mask_ack is slightly more efficient than just
implementing irq_mask and irq_ack separately.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Use the of_device_get_match_data() helper instead of open coding.
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a menu for IRQ chip drivers. This makes the Device drivers menu be more
consistent (listing "subsystems" instead of specific options) and makes the
IRQCHIP options be listed in expected places for 'make menu|xconfig'.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/3db7385a-c6a1-5c93-0797-6f4b6b2b2cde@infradead.org
omap_nr_pending and omap_nr_irqs variables are initialized
right at the beginning of intc_of_init function, so there's
no need to statically initialize them.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20171016161303.veumgcd3xom5c54r@lenoch
All mach-omap2 variants are device tree only now, so this function is dead
code. Remove it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-omap@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20171016160422.uu2i7vvrgy7cc4aw@lenoch
The only usage of the irq_gc_mask_disable_reg_and_ack() function
is by the Tango irqchip driver. This usage is replaced by the
irq_gc_mask_disable_and_ack_set() function since it provides the
intended functionality.
Fixes: 4bba66899a ("irqchip/tango: Add support for Sigma Designs SMP86xx/SMP87xx interrupt controller")
Acked-by: Mans Rullgard <mans@mansr.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The current ITS driver works fine as long as normal memory and GICR
regions are located within the lower 48bit (>=0 && <2^48) physical
address space. Some of the registers GICR_PEND/PROP, GICR_VPEND/VPROP
and GITS_CBASER are handled properly but not all when configuring
the hardware with 52bit physical address.
This patch does the following changes to support 52bit PA.
-Handle 52bit PA in GITS_BASERn.
-Fix ITT_addr width to 52bits, bits[51:8].
-Fix RDbase width to 52bits, bits[51:16].
-Fix VPT_addr width to 52bits, bits[51:16].
Definition of the GITS_BASERn register when ITS PageSize is 64KB:
-Bits[47:16] of the register provide bits[47:16] of the table PA.
-Bits[15:12] of the register provide bits[51:48] of the table PA.
-Bits[15:00] of the base physical address are 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The VCPU table consists of vPE entries, and its size provides the number
of VPEs supported by GICv4 hardware. Unfortunately the maximum size of
the VPE table is not discoverable like Device table. All VLPI commands
limits the number of bits to 16 to hold VPEID, which is index into VCPU
table. Don't apply DEVID bits for VCPU table instead assume maximum bits
to 16.
ITS log messages on QDF2400 without fix:
allocated 524288 Devices (indirect, esz 8, psz 64K, shr 1)
allocated 8192 Interrupt Collections (flat, esz 8, psz 64K, shr 1)
Virtual CPUs Table too large, reduce ids 32->26
Virtual CPUs too large, reduce ITS pages 8192->256
allocated 2097152 Virtual CPUs (flat, esz 8, psz 64K, shr 1)
ITS log messages on QDF2400 with fix:
allocated 524288 Devices (indirect, esz 8, psz 64K, shr 1)
allocated 8192 Interrupt Collections (flat, esz 8, psz 64K, shr 1)
allocated 65536 Virtual CPUs (flat, esz 8, psz 64K, shr 1)
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The driver probe path hits 'BUG_ON(entries != vpe_proxy.dev->nr_ites)'
on systems where it has VLPI capability, doesn't support direct LPI
feature and boot with a single CPU.
Relax the BUG_ON() condition to fix the issue.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ls1012a implements only 1 MSI controller, and it is the same as
ls1043a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Commit 7778c4b27c ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") adjusted the way we handle masking interrupts to set &
clear the interrupt's bit in each pcpu_mask. This allows us to avoid
needing to read the GIC mask registers and perform a bitwise and of
their values with the pending & pcpu_masks.
Unfortunately this didn't quite work for IPIs, which were mapped to a
particular CPU/VP during initialisation but never set the affinity or
effective_affinity fields of their struct irq_desc. This led to them
losing their affinity when gic_unmask_irq() was called for them, and
they'd all become affine to cpu0.
Fix this by:
1) Setting the effective affinity of interrupts in
gic_shared_irq_domain_map(), which is where we actually map an
interrupt to a CPU/VP. This ensures that the effective affinity mask
is always valid, not just after explicitly setting affinity.
2) Using an interrupt's effective affinity when unmasking it, which
prevents gic_unmask_irq() from unintentionally changing which
pcpu_mask includes an interrupt.
Fixes: 7778c4b27c ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20170922062440.23701-3-paul.burton@imgtec.com
The MIPS GIC driver is incorrectly using __fls to shift registers,
intending to shift to the least significant bit of a value based upon
its mask but instead shifting off all but the value's top bit. It should
actually be using __ffs to shift to the first, not last, bit of the
value.
Apparently the system I used when testing commit 3680746abd
("irqchip: mips-gic: Convert remaining shared reg access to new
accessors") and commit b2b2e584ce ("irqchip: mips-gic: Clean up mti,
reserved-cpu-vectors handling") managed to work correctly despite this
issue, but not all systems do...
Fixes: 3680746abd ("irqchip: mips-gic: Convert remaining shared reg access to new accessors")
Fixes: b2b2e584ce ("irqchip: mips-gic: Clean up mti, reserved-cpu-vectors handling")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20170922062440.23701-2-paul.burton@imgtec.com
In order to easily provide SMP for BCM2837 on 32-bit and 64-bit
the SMP startup code was placed in irq-bcm2836. That's not the
right approach. So move this code where it belongs.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 41f4988cc2 ("irqchip/bcm2836: Add SMP support for the 2836")
Tested-by: Eric Anholt <eric@anholt.net>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.
The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:
- A return value, so activation can fail at request_irq() time
- Information that the activate invocation is early, i.e. before
request_irq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.848490816@linutronix.de
The write_gic_smask() & write_gic_rmask() functions take a shared
interrupt number as a parameter, but we're incorrectly providing them a
bitmask with the shared interrupt's bit set. This effectively means that
we mask or unmask the shared interrupt 1<<n rather than shared interrupt
n, and as a result likely drop interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 68898c8765f4 ("irqchip: mips-gic: Drop gic_(re)set_mask() functions")
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
gcc-4.5 and earlier don't like named initializers for anonymous
union members:
drivers/irqchip/irq-gic-v4.c: In function 'its_map_vlpi':
drivers/irqchip/irq-gic-v4.c:176:3: error: unknown field 'map' specified in initializer
drivers/irqchip/irq-gic-v4.c:176:3: error: missing braces around initializer
drivers/irqchip/irq-gic-v4.c:176:3: error: (near initialization for 'info.<anonymous>')
drivers/irqchip/irq-gic-v4.c: In function 'its_get_vlpi':
drivers/irqchip/irq-gic-v4.c:192:3: error: unknown field 'map' specified in initializer
drivers/irqchip/irq-gic-v4.c:192:3: error: missing braces around initializer
drivers/irqchip/irq-gic-v4.c:192:3: error: (near initialization for 'info.<anonymous>')
drivers/irqchip/irq-gic-v4.c: In function 'its_prop_update_vlpi':
drivers/irqchip/irq-gic-v4.c:208:3: error: unknown field 'config' specified in initializer
drivers/irqchip/irq-gic-v4.c:208:3: error: missing braces around initializer
drivers/irqchip/irq-gic-v4.c:208:3: error: (near initialization for 'info.<anonymous>')
drivers/irqchip/irq-gic-v4.c:208:3: error: initialization makes pointer from integer without a cast
This is fairly easy to work around, by using extra curly braces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
get_cpu_number() doesn't use existing helper to iterate over possible
CPUs, It will cause an error in case of discontinuous @cpu_possible_mask
such as 0b11110001, which can result from a core having failed to come
up on a SMP machine.
Fixed by using existing helper for_each_possible_cpu().
Signed-off-by: zijun_hu <zijun_hu@htc.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
Pull irq updates from Thomas Gleixner:
"The interrupt subsystem delivers this time:
- Refactoring of the GIC-V3 driver to prepare for the GIC-V4 support
- Initial GIC-V4 support
- Consolidation of the FSL MSI support
- Utilize the effective affinity interface in various ARM irqchip
drivers
- Yet another interrupt chip driver (UniPhier AIDET)
- Bulk conversion of the irq chip driver to use %pOF
- The usual small fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
irqchip/ls-scfg-msi: Add MSI affinity support
irqchip/ls-scfg-msi: Add LS1043a v1.1 MSI support
irqchip/ls-scfg-msi: Add LS1046a MSI support
arm64: dts: ls1046a: Add MSI dts node
arm64: dts: ls1043a: Share all MSIs
arm: dts: ls1021a: Share all MSIs
arm64: dts: ls1043a: Fix typo of MSI compatible string
arm: dts: ls1021a: Fix typo of MSI compatible string
irqchip/ls-scfg-msi: Fix typo of MSI compatible strings
irqchip/irq-bcm7120-l2: Use correct I/O accessors for irq_fwd_mask
irqchip/mmp: Make mmp_intc_conf const
irqchip/gic: Make irq_chip const
irqchip/gic-v3: Advertise GICv4 support to KVM
irqchip/gic-v4: Enable low-level GICv4 operations
irqchip/gic-v4: Add some basic documentation
irqchip/gic-v4: Add VLPI configuration interface
irqchip/gic-v4: Add VPE command interface
irqchip/gic-v4: Add per-VM VPE domain creation
irqchip/gic-v3-its: Set implementation defined bit to enable VLPIs
irqchip/gic-v3-its: Allow doorbell interrupts to be injected/cleared
...
gic_set_affinity() manually copies the provided cpumask to the struct
irq_common_data affinity field, returning IRQ_SET_MASK_OK_NOCOPY in
order to prevent the core code from doing that.
We can instead simply let the core code do it for us, by returning
IRQ_SET_MASK_OK instead of IRQ_SET_MASK_OK_NOCOPY & doing the copy
ourselves.
[ralf@linux-mips.org: Resolve merge conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17056/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently in gic_set_affinity() we calculate a temporary cpumask holding
the intersection of the provided cpumask & the CPUs that are online,
then we call cpumask_first twice on it to find the first such CPU. Since
we don't need the temporary cpumask for anything else & we only care
about the first CPU that's both online & in the provided cpumask, we can
instead use cpumask_first_and to find that CPU & drop the temporary
mask.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17110/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When parsing mti,reserved-cpu-vectors we generate a mask of all bits
that have been declared reserved, the loop through starting from bit 2
to find one that isn't reserved (ie. is zero).
This patch accomplishes the same task more simply by:
- Inititialising the reserved mask to 0x3 (ie. the 2 software
interrupts). This means we don't need to skip them later as the loop
previously has.
- Replacing the loop checking for zero bits with find_first_zero_bit,
which fits our needs now that the 2 software interrupts are marked
reserved. This requires that the type of reserved is changed to
unsigned long so that it's suitable for use with bitmap functions.
- Replacing the magic number 8 with the hamming weight of the ST0_IM
field - ie. the number of bits that a MIPS CPU has for interrupt
inputs. This is still a compile-time constant 8, but makes it
clearer why it's 8.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17054/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch avoids the need to read the GIC_SH_MASK* registers when
decoding shared interrupts by setting & clearing the interrupt's bit in
the appropriate CPU's pcpu_masks entry when masking or unmasking the
interrupt.
This effectively means that whilst an interrupt is masked we clear its
bit in all pcpu_masks, which causes gic_handle_shared_int() to ignore it
on all CPUs without needing to check GIC_SH_MASK*.
In essence, we add a little overhead to masking or unmasking interrupts
but in return reduce the overhead of the far more common task of
decoding interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17109/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Define the pcpu_masks variable using the kernel's standard per-cpu
variable support, rather than an open-coded array of structs containing
bitmaps.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17052/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
gic_basic_init() is now a fairly short function that is only called in
one place. Inline it into gic_of_init() to help readability.
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17051/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The __gic_init() function is only called from gic_of_init() now that the
non-DT path has been removed. In order to simplify the code & aid
readability, fold __gic_init() into gic_of_init().
This provides us with the ability to return an error code, which
__gic_init() was previously unable to do. As such the irq_domain_add_*()
error paths are modified to print & return an error rather than panic().
[ralf@linux-mips.org: Resoled reject.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17050/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The linux/irqchip/mips-gic.h header is now almost empty. Move the
declarations of gic_get_c0_compare_int(), gic_get_c0_perfcount_int() &
gic_get_c0_fdc_int() to asm/mips-gic.h in order to close in on being
able to delete the former header.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17046/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nothing uses the global gic_present variable anymore; mips_gic_present()
should be used instead. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17045/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All in-tree platforms now probe the GIC driver using device tree, and as
such nothing calls gic_init() any longer. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17043/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We provide a forward declaration of the __gic_irq_dispatch() function
for no apparent reason. Remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17042/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS VDSO code is no longer reliant upon the irqchip driver to
provide the address of the GIC's user-visible section via
gic_get_usm_range(). Remove the now-dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17041/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the definitions of macros used to convert between hardware IRQ
numbers & shared or local interrupt numbers into the irqchip driver,
which is all that should ever need to care about them.
Remove GIC_CPU_TO_VEC_OFFSET() in the process since it's never used.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17039/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the remaining accesses to registers in the GIC VP-local &
VP-other register blocks to use the new accessor functions provided by
asm/mips-gic.h, resulting in code which is often shorter & easier to
read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17036/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the new accessor functions provided by asm/mips-gic.h to access
masks controlling local interrupts, resulting in code which is often
shorter & easier to read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17035/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the remaining accesses to registers in the GIC shared register
block to use the new accessor functions provided by asm/mips-gic.h,
resulting in code which is often shorter & easier to read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17034/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_map_to_vpe() function in favour of using the new
write_gic_map_vp() accessor function which isn't any more complex to
use & allows us to drop a level of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17033/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_map_to_pin() function in favour of using the new
write_gic_map_pin() accessor function which isn't any more complex to
use & allows us to drop a level of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_set_dual_edge() function in favour of using the new
change_gic_dual() accessor function which provides equivalent
functionality. This also allows us to remove the gic_update_bits()
function which gic_set_dual_edge() was the last user of, along with the
GIC_INTR_OFS() & GIC_INTR_BIT() macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17031/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_set_trigger() function in favour of using the new
change_gic_trig() accessor function which provides equivalent
functionality.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17030/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_set_polarity() function in favour of using the new
change_gic_pol() accessor function which provides equivalent
functionality.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17029/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The gic_set_mask() & gic_reset_mask() functions are now no more
convenient to call than the write_gic_smask() or write_gic_rmask()
accessor functions. Remove the layer of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17028/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simplify gic_local_irq_domain_map() by:
- Moving the check for invalid IRQs outside of the loop.
- Moving the decision about whether to use gic_cpu_pin or timer_cpu_pin
outside of the loop.
- Using the new write_gic_vo_map() accessor function to avoid the need
to handle each map register separately.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17027/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simplify the reads of the bitmaps indicating pending & masked interrupts
in gic_handle_shared_int() using the __ioread32_copy() &
__ioread64_copy() helper functions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17026/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nothing needs gic_read_local_vp_id() any longer, so remove the dead
code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17024/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS GIC clocksource driver is no longer using the accessor
functions provided by the irqchip driver, so remove them.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17022/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- irqchip-specific part of the monster GICv4 series
- new UniPhier AIDET irqchip driver
- new variants of some Freescale MSI widget
- blanket removal of of_node->full_name in printk
- random collection of fixes
-----BEGIN PGP SIGNATURE-----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=3ZS3
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates for 4.14 from Marc Zyngier:
- irqchip-specific part of the monster GICv4 series
- new UniPhier AIDET irqchip driver
- new variants of some Freescale MSI widget
- blanket removal of of_node->full_name in printk
- random collection of fixes
For LS1046a and LS1043a v1.1, the MSI controller has 4 MSIRs and 4 GIC
SPI interrupts which can be associated with different Core.
So we can support affinity to improve the performance.
The MSI message data is a byte for Layerscape MSI.
7 6 5 4 3 2 1 0
| - | IBS | SRS |
SRS bit0-1 is to select a MSIR which is associated with a CPU.
IBS bit2-6 of ls1046, bit2-4 of ls1043a v1.1 is to select bit of the
MSIR. With affinity, only bits of MSIR0(srs=0 cpu0) are available.
All other bits of the MSIR1-3(cpu1-3) are reserved. The MSI hwirq
always equals bit index of the MSIR0. When changing affinity, MSI
message data will be appended corresponding SRS then MSI will be
moved to the corresponding core.
But in affinity mode, there is only 8 MSI interrupts for a controller
of LS1043a v1.1. It cannot meet the requirement of the some PCIe
devices such as 4 ports Ethernet card. In contrast, without affinity,
all MSIRs can be used for core 0, the MSI interrupts can up to 32.
So the parameter is added to control affinity mode.
"lsmsi=no-affinity" will disable affinity and increase MSI
interrupt number.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A MSI controller of LS1043a v1.0 only includes one MSIR and
is assigned one GIC interrupt. In order to support affinity,
LS1043a v1.1 MSI is assigned 4 MSIRs and 4 GIC interrupts.
But the MSIR has the different offset and only supports 8 MSIs.
The bits between variable bit_start and bit_end in structure
ls_scfg_msir are used to show 8 MSI interrupts. msir_irqs and
msir_base are added to describe the difference of MSI between
LS1043a v1.1 and other SoCs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
LS1046a includes 4 MSIRs, each MSIR is assigned a dedicate GIC
SPI interrupt and provides 32 MSI interrupts. Compared to previous
MSI, LS1046a's IBS(interrupt bit select) shift is changed to 2 and
total MSI interrupt number is changed to 128.
The patch adds structure 'ls_scfg_msir' to describe MSIR setting and
'ibs_shift' to store the different value between the SoCs.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The patch is to fix typo of the Layerscape SCFG MSI dts compatible
strings. "1" is replaced by "l".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Initialization of irq_fwd_mask was done using __raw_writel() which
happens to work for all cases except when using ARM BE8 which requires
writel() (with the proper swapping). Move the initialization of the
irq_fwd_mask till later when we have correctly defined our I/O
accessors.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make these const as they are only used during a copy operation. Done
using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct mmp_intc_conf s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct mmp_intc_conf s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make this const as it is only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As KVM needs to know about the availability of GICv4 to enable
direct injection of interrupts, let's advertise the feature in
the gic_kvm_info structure.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Do a braindump of the way things are supposed to work.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the required interfaces to map, unmap and update a VLPI.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the required interfaces to schedule a VPE and perform a
VINVALL command.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When creating a VM, it is very convenient to have an irq domain
containing all the doorbell interrupts associated with that VM
(each interrupt representing a VPE).
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A long time ago, GITS_CTLR[1] used to be called GITC_CTLR.EnableVLPI.
It has been subsequently deprecated and is now an "Implementation
Defined" bit that may ot may not be set for GICv4. Brilliant.
And the current crop of the FastModel requires that bit for VLPIs
to be enabled. Oh well... Let's set it and find out what breaks.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
While the doorbell interrupts are usually driven by the HW itself,
having a way to trigger them independently has proved to be a
really useful debug feature. As it is actually very little code,
let's add it to the VPE irqchip operations.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
After moving a VPE from a redistributor to another, we're still left
with a potential pending doorbell interrupt on the old redistributor.
That interrupt should be moved to the new one to be either cleared
or take, depending on what the hypervisor wishes to do.
So let's move it right after having execited VMOVP. This doesn't
add much cost in the !DirectLPI case (we trade a DISCARD for a MOVI),
and the cost of the DIRECTLPI case should be minimal (two extra MMIO
accesses).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When we don't have the DirectLPI feature, we must work around the
architecture shortcomings to be able to perform the required
maintenance (interrupt masking, clearing and injection).
For this, we create a fake device whose sole purpose is to
provide a way to issue commands as if we were dealing with LPIs
coming from that device (while they actually originate from
the ITS). This fake device doesn't have LPIs allocated to it,
but instead uses the VPE LPIs.
Of course, this could be a real bottleneck, and a naive
implementation would require 6 commands to issue an invalidation.
Instead, let's allocate at least one event per physical CPU
(rounded up to the next power of 2), and opportunistically
map the VPE doorbell to an event. This doorbell will be mapped
until we roll over and need to reallocate this slot.
This ensures that most of the time, we only need 2 commands
to issue an INV, INT or CLEAR, making the performance a lot
better, given that we always issue a CLEAR on entry, and
an INV on each side of a trapped WFI.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The normal course of action when allocating the ITS' view of a
device is to allocate the corresponding LPIs. But we're about
to introduce devices that borrow their interrupts from
some other entities.
So let's make the allocation optional.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When masking/unmasking a doorbell interrupt, it is necessary
to issue an invalidation to the corresponding redistributor.
We use the DirectLPI feature by writting directly to the corresponding
redistributor.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When we're about to run a vcpu, it is crucial that the redistributor
associated with the physical CPU is being told about the new residency.
This is abstracted by hijacking the irq_set_affinity method for the
doorbell interrupt associated with the VPE. It is expected that the
hypervisor will call this method before scheduling the VPE.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When a guest issues a INVALL command targetting a collection, it must
be translated into a VINVALL for the VPE that has this collection.
This patch implements a hook that offers this functionallity to the
hypervisor.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When a VPE is scheduled to run, the corresponding redistributor must
be told so, by setting VPROPBASER to the VM's property table, and
VPENDBASER to the vcpu's pending table.
When scheduled out, we preserve the IDAI and PendingLast bits. The
latter is specially important, as it tells the hypervisor that
there are pending interrupts for this vcpu.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On activation, a VPE is mapped using the VMAPP command, followed
by a VINVALL for a good measure. On deactivation, the VPE is
simply unmapped.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When creating a VM, the low level GICv4 code is responsible for:
- allocating each VPE a unique VPEID
- allocating a doorbell interrupt for each VPE
- allocating the pending tables for each VPE
- allocating the property table for the VM
This of course has to be reversed when the VM is brought down.
All of this is wired into the irq domain alloc/free methods.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the basic GICv4 VPE (vcpu in GICv4 parlance) infrastructure
(irqchip, irq domain) that is going to be populated in the following
patches.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When a VLPI is reconfigured (enabled, disabled, change in priority),
the full configuration byte must be written, and the caches invalidated.
Also, when using the irq_mask/irq_unmask methods, it is necessary
to disable the doorbell for that particular interrupt (by mapping it
to 1023) on top of clearing the Enable bit.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to let a VLPI being injected into a guest, the VLPI must
be mapped using the VMAPTI command. When moved to a different vcpu,
it must be moved with the VMOVI command.
These commands are issued via the irq_set_vcpu_affinity method,
making sure we unmap the corresponding host LPI first.
The reverse is also done when the VLPI is unmapped from the guest.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the skeleton irq_set_vcpu_affinity method that will be used
to configure VLPIs.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the new GICv4 ITS command definitions, most of them, being
defined in terms of their physical counterparts.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch introduces a new header providing accessor functions for the
MIPS Global Interrupt Controller (GIC) mirroring those provided for the
other 2 components of the MIPS Coherent Processing System (CPS) - the
Coherence Manager (CM) & Cluster Power Controller (CPC).
This header makes use of the new standardised CPS accessor macros where
possible, but does require some custom accessors for cases where we have
either a bit or a register per interrupt.
A major advantage of this over the existing
include/linux/irqchip/mips-gic.h definitions is that code performing
accesses can become much simpler, for example this:
gic_update_bits(GIC_REG(SHARED, GIC_SH_SET_TRIGGER) +
GIC_INTR_OFS(intr), 1ul << GIC_INTR_BIT(intr),
(unsigned long)trig << GIC_INTR_BIT(intr));
...can become simply:
change_gic_trig(intr, trig);
The accessors handle 32 vs 64 bit in the same way as for CM & CPC code,
which means that GIC code will also not need to worry about the access
size in most cases. They are also accessible outside of
drivers/irqchip/irq-mips-gic.c which will allow for simplification in
the use of the non-interrupt portions of the GIC (eg. counters) which
currently require the interrupt controller driver to expose helper
functions for access.
This patch doesn't change any existing code over to use the new
accessors yet, since a wholesale change would be invasive & difficult to
review. Instead follow-on patches will convert code piecemeal to use
this new header. The one change to existing code is to rename gic_base
to mips_gic_base & make it global, in order to fit in with the naming
expected by the standardised CPS accessor macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17020/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A SYNC is required between enabling the GIC region and actually trying
to use it, even if the first access is a read, otherwise its possible
depending on the timing (and in my case depending on the precise
alignment of certain kernel code) to hit CM bus errors on that first
access.
Add the SYNC straight after setting the GIC base.
[paul.burton@imgtec.com:
Changes later in this series increase our likelihood of hitting this
by reducing the amount of code that runs between enabling the GIC &
accessing it.]
Fixes: a7057270c2 ("irqchip: mips-gic: Add device-tree support")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17019/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A SYNC is required between enabling the GIC region and actually trying
to use it, even if the first access is a read, otherwise its possible
depending on the timing (and in my case depending on the precise
alignment of certain kernel code) to hit CM bus errors on that first
access.
Add the SYNC straight after setting the GIC base.
[paul.burton@imgtec.com:
Changes later in this series increase our likelihood of hitting this
by reducing the amount of code that runs between enabling the GIC &
accessing it.]
Fixes: a7057270c2 ("irqchip: mips-gic: Add device-tree support")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.19.x-
Patchwork: https://patchwork.linux-mips.org/patch/17019/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With Coherence Manager (CM) 3.5 information about the topology of the
system, which has previously only been available through & accessed from
the CM, is now also provided by the Cluster Power Controller (CPC). This
includes a new CPC_CONFIG register mirroring GCR_CONFIG, and similarly a
new CPC_Cx_CONFIG register mirroring GCR_Cx_CONFIG.
In preparation for adjusting functions such as mips_cm_numcores(), which
have previously only needed to access the CM, to also access the CPC
this patch modifies the way we use the various CPS headers. Rather than
having users include asm/mips-cm.h or asm/mips-cpc.h individually we
instead have users include asm/mips-cps.h which in turn includes
asm/mips-cm.h & asm/mips-cpc.h. This means that users will gain access
to both CM & CPC registers by including one header, and most importantly
it makes asm/mips-cps.h an ideal location for helper functions which
need to access the various components of the CPS.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17015/
Patchwork: https://patchwork.linux-mips.org/patch/17217/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Up until now we have open-coded checks for whether CPUs are siblings,
with slight variations on whether we consider the package ID or not.
This will only get more complex when we introduce cluster support, so in
preparation for that this patch introduces a cpus_are_siblings()
function which can be used to check whether or not 2 CPUs are siblings
in a consistent manner.
By checking globalnumber with the VP ID masked out this also has the
neat side effect of being ready for multi-cluster systems already.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17011/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There's no reason for us not to use BIT() & GENMASK() in asm/mips-cm.h
when declaring macros corresponding to register fields. This patch
modifies our definitions to do so.
The *_SHF definitions are removed entirely - they duplicate information
found in the masks, are infrequently used & can be replaced with use of
__ffs() where needed.
The *_MSK definitions then lose their _MSK suffix which is now somewhat
redundant, and users are modified to match.
The field definitions are moved to follow the appropriate register's
accessor functions, which helps to keep the field definitions in order &
to find the appropriate fields for a given register. Whilst here a
comment is added describing each register & including its name, which is
helpful both for linking the register back to hardware documentation &
for grepping purposes.
This also cleans up a couple of issues that became obvious as a result
of making the changes described above:
- We previously had definitions for GCR_Cx_RESET_EXT_BASE & a phony
copy of that named GCR_RESET_EXT_BASE - a register which does not
exist. The bad definitions were added by commit 497e803ebf ("MIPS:
smp-cps: Ensure secondary cores start with EVA disabled") and made
use of from boot_core(), which is now modified to use the
GCR_Cx_RESET_EXT_BASE definitions.
- We had a typo in CM_GCR_ERROR_CAUSE_ERRINGO_MSK - we now correctly
define this as inFo rather than inGo.
Now that we don't duplicate field information between _SHF & _MSK
definitions, and keep the fields next to the register accessors, it will
be much easier to spot & prevent any similar oddities being introduced
in the future.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17001/
Patchwork: https://patchwork.linux-mips.org/patch/17216/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We're are going to need to change a bit more than just the enable
bit in the LPI property table in the future. So let's change the
LPI configuration funtion to take a set of bits to be cleared,
and a set of bits to be set.
This way, we'll be able to use it when a guest updates an LPI
property (priority, for example).
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we want to use 2-level tables for VCPUs, let's hack the device
table allocator in order to make it slightly more generic. It
will get reused in subsequent patches.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Rework LPI deallocation so that it can be reused by the v4 support
code.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Just as for the property table, let's move the pending table
allocation to a separate function.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The VCPU tables can be quite sparse as well, and it makes sense
to use indirect tables as well if possible.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Move the LPI property table allocation into its own function, as
this is going to be required for those associated with VMs in
the future.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Allow the pending state of an LPI to be set or cleared via
irq_set_irqchip_state.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Most ITS commands do operate on a collection object, and require
a SYNC command to be performed on that collection in order to
guarantee the execution of the first command.
With GICv4 ITS, another set of commands perform similar operations
on a VPE object, and a VSYNC operations must be executed to guarantee
their execution.
Given the similarities (post a command, perform a synchronization
operation on a sync object), it makes sense to reuse the same
mechanism for both class of commands.
Let's start with turning its_send_single_command into a huge macro
that performs the bulk of the work, and a set of helpers that
make this macro usable for the GICv3 ITS commands.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the probing code for the ITS VLPI support. This includes
configuring the ITS number if not supporting the single VMOVP
command feature.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The various LPI definitions are in the middle of the code, and
would be better placed at the beginning, given that we're going
to use some of them much earlier.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add helper functions that probe for VLPI and DirectLPI properties.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to discover the VLPI properties, we need to iterate over
the redistributor regions. As we already have code that does this,
let's factor it out and make it slightly more generic.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lee Jones <lee@kernel.org>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
UniPhier SoCs contain AIDET (ARM Interrupt Detector). This is intended
to provide additional features that are not covered by GIC. The main
purpose is to provide logic inverter to support low level and falling
edge trigger types for interrupt lines from on-board devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
wait_for_range_completion() is nicely busted when handling
wrapping of the command queue, leading to an early exit
instead of waiting for the command to have been executed.
Fortunately, the impact is pretty minor, as it only impair
the detection of an ITS that doesn't make any forward progress
for a whole second. And an ITS should *never* lock up.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Armada XP does not only support MSI, but also MSI-X. This patch sets
the MSI_FLAG_PCI_MSIX flag in the interrupt controller driver which
is the only change necessary to enable MSI-X support on this SoC. As
the Linux PCI MSI-X infrastructure takes care of writing the data and
address structures into the BAR specified by the MSI-X controller.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The xtensa-mx driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-13-marc.zyngier@arm.com
The MIPS GIC driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-12-marc.zyngier@arm.com
The HIP04 driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-11-marc.zyngier@arm.com
The metag-ext driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-10-marc.zyngier@arm.com
The BCM 7038-L1 driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-9-marc.zyngier@arm.com
The BCM 6345-L1 driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-8-marc.zyngier@arm.com
The Armada 370 XP driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-7-marc.zyngier@arm.com
The GICv3 ITS driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-6-marc.zyngier@arm.com
The GICv3 driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-5-marc.zyngier@arm.com
The GIC driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-4-marc.zyngier@arm.com
While parsing the msi-parent property to chase up the IRQ domain
a given device belongs to, the index into the msi-parent tuple should
be incremented to ensure all properties entries are taken into account.
Current code missed the index update so the parsing loop does not work
in case multiple msi-parent phandles are present and may turn into
an infinite loop in of_pmsi_get_dev_id() if phandle at index 0 does
not correspond to the domain we are actually looking-up.
Fix the code by updating the phandle index at each iteration in
of_pmsi_get_dev_id().
Fixes: deac7fc1c8 ("irqchip/gic-v3-its: Parse new version of msi-parent property")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When enabling ITS NUMA support on D05, I got the boot log:
[ 0.000000] SRAT: PXM 0 -> ITS 0 -> Node 0
[ 0.000000] SRAT: PXM 0 -> ITS 1 -> Node 0
[ 0.000000] SRAT: PXM 0 -> ITS 2 -> Node 0
[ 0.000000] SRAT: PXM 1 -> ITS 3 -> Node 1
[ 0.000000] SRAT: ITS affinity exceeding max count[4]
This is wrong on D05 as we have 8 ITSs with 4 NUMA nodes.
So dynamically alloc the memory needed instead of using
its_srat_maps[MAX_NUMNODES], which count the number of
ITS entry(ies) in SRAT and alloc its_srat_maps as needed,
then build the mapping of numa node to ITS ID. Of course,
its_srat_maps will be freed after ITS probing because
we don't need that after boot.
After doing this, I got what I wanted:
[ 0.000000] SRAT: PXM 0 -> ITS 0 -> Node 0
[ 0.000000] SRAT: PXM 0 -> ITS 1 -> Node 0
[ 0.000000] SRAT: PXM 0 -> ITS 2 -> Node 0
[ 0.000000] SRAT: PXM 1 -> ITS 3 -> Node 1
[ 0.000000] SRAT: PXM 2 -> ITS 4 -> Node 2
[ 0.000000] SRAT: PXM 2 -> ITS 5 -> Node 2
[ 0.000000] SRAT: PXM 2 -> ITS 6 -> Node 2
[ 0.000000] SRAT: PXM 3 -> ITS 7 -> Node 3
Fixes: dbd2b82672 ("irqchip/gic-v3-its: Add ACPI NUMA node mapping")
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
Cc: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Broadcom STB platforms support S5 and we allow specific hardware
wake-up events to take us out of this state. Because we were not
defining an irq_pm_shutdown() function pointer, we would not be
correctly masking non-wakeup events, which would result in spurious
wake-ups from sources that were not explicitly configured for wake-up.
Fixes: 7f646e9276 ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller")
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Devices that expose their interrupt status registers via system
registers (e.g. Statistical profiling, CPU PMU, DynamIQ PMU, arch timer,
vgic (although unused by Linux), ...) rely on a context synchronising
operation on the CPU to ensure that the updated status register is
visible to the CPU when handling the interrupt. This usually happens as
a result of taking the IRQ exception in the first place, but there are
two race scenarios where this isn't the case.
For example, let's say we have two peripherals (X and Y), where Y uses a
system register for its interrupt status.
Case 1:
1. CPU takes an IRQ exception as a result of X raising an interrupt
2. Y then raises its interrupt line, but the update to its system
register is not yet visible to the CPU
3. The GIC decides to expose Y's interrupt number first in the Ack
register
4. The CPU runs the IRQ handler for Y, but the status register is stale
Case 2:
1. CPU takes an IRQ exception as a result of X raising an interrupt
2. CPU reads the interrupt number for X from the Ack register and runs
its IRQ handler
3. Y raises its interrupt line and the Ack register is updated, but
again, the update to its system register is not yet visible to the
CPU.
4. Since the GIC drivers poll the Ack register, we read Y's interrupt
number and run its handler without a context synchronisation
operation, therefore seeing the stale register value.
In either case, we run the risk of missing an IRQ. This patch solves the
problem by ensuring that we execute an ISB in the GIC drivers prior
to invoking the interrupt handler. This is already the case for GICv3
and EOIMode 1 (the usual case for the host).
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The version check was added due to dependency to
a618c7f89a ACPICA: Add support for new SRAT subtable
Now, that this code is in the kernel, remove the check. This is esp.
useful to enable backports.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Cc: keescook@chromium.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1500149266-32357-11-git-send-email-Julia.Lawall@lip6.fr
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: keescook@chromium.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1500149266-32357-7-git-send-email-Julia.Lawall@lip6.fr
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: keescook@chromium.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1500149266-32357-6-git-send-email-Julia.Lawall@lip6.fr
Since commit d59f6617ee ("genirq: Allow fwnode to carry name
information only") the irqdomain core sets the names of irq domains.
When the name is allocated the new IRQ_DOMAIN_NAME_ALLOCATED flag is
set. Replacing the allocated name with a constant one is not a good
idea, since calling the new irq_domain_update_bus_token() API, added to
the MIPS GIC driver by commit 96f0d93a48 ("irqchip/MSI: Use
irq_domain_update_bus_token instead of an open coded access") will
attempt to kfree the pointer, and result in a kernel OOPS.
Fix this by removing the names, now that they are set by the irqdomain
core. This effectively reverts commit 21c57fd135 ("irqchip/mips-gic:
Populate irq_domain names").
Fixes: d59f6617ee ("genirq: Allow fwnode to carry name information only")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1500363561-32213-1-git-send-email-matt.redfearn@imgtec.com
Honor the 'force' flag for set_affinity, by selecting a CPU
from the given mask (which may not be reported "online" by
the cpu_online_mask). Some drivers, like ARM PMU, rely on it.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the GIC cannot map an IRQ via irq_domain_ops->alloc(), it doesn't
return an error code. This can cause a problem with drivers, where
it thinks it has successfully got an IRQ for the device, but requesting
the same ends up failure with -ENOSYS (as the IRQ's chip is not set).
Fixes: commit 443acc4f37 ("irqchip: GICv3: Convert to domain hierarchy")
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the GIC cannot map an IRQ via irq_domain_ops->alloc(), it doesn't
return an error code. This can cause a problem with drivers, where
it thinks it has successfully got an IRQ for the device, but requesting
the same ends up failure with -ENOSYS (as the IRQ's chip is not set).
Fixes: commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq domain.")
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We are no longer using the root argument passed to the ->fixup() hooks.
Remove it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
of_find_compatible_node() is calling of_node_put() on its first argument
thus leading to an unbalanced of_node_get/put() issue if the node has not
been retained before that.
Instead of passing the root node, pass NULL, which does exactly the same:
iterate over all DT nodes, starting from the root node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: 3d61467f9b ("irqchip: atmel-aic: Implement RTC irq fixup")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
aic_common_irq_fixup() is calling twice of_node_put() on the same node
thus leading to an unbalanced refcount on the root node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: b2f579b58e ("irqchip: atmel-aic: Add irq fixup infrastructure")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull irq updates from Thomas Gleixner:
"The irq department delivers:
- Expand the generic infrastructure handling the irq migration on CPU
hotplug and convert X86 over to it. (Thomas Gleixner)
Aside of consolidating code this is a preparatory change for:
- Finalizing the affinity management for multi-queue devices. The
main change here is to shut down interrupts which are affine to a
outgoing CPU and reenabling them when the CPU comes online again.
That avoids moving interrupts pointlessly around and breaking and
reestablishing affinities for no value. (Christoph Hellwig)
Note: This contains also the BLOCK-MQ and NVME changes which depend
on the rework of the irq core infrastructure. Jens acked them and
agreed that they should go with the irq changes.
- Consolidation of irq domain code (Marc Zyngier)
- State tracking consolidation in the core code (Jeffy Chen)
- Add debug infrastructure for hierarchical irq domains (Thomas
Gleixner)
- Infrastructure enhancement for managing generic interrupt chips via
devmem (Bartosz Golaszewski)
- Constification work all over the place (Tobias Klauser)
- Two new interrupt controller drivers for MVEBU (Thomas Petazzoni)
- The usual set of fixes, updates and enhancements all over the
place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (112 commits)
irqchip/or1k-pic: Fix interrupt acknowledgement
irqchip/irq-mvebu-gicp: Allocate enough memory for spi_bitmap
irqchip/gic-v3: Fix out-of-bound access in gic_set_affinity
nvme: Allocate queues for all possible CPUs
blk-mq: Create hctx for each present CPU
blk-mq: Include all present CPUs in the default queue mapping
genirq: Avoid unnecessary low level irq function calls
genirq: Set irq masked state when initializing irq_desc
genirq/timings: Add infrastructure for estimating the next interrupt arrival time
genirq/timings: Add infrastructure to track the interrupt timings
genirq/debugfs: Remove pointless NULL pointer check
irqchip/gic-v3-its: Don't assume GICv3 hardware supports 16bit INTID
irqchip/gic-v3-its: Add ACPI NUMA node mapping
irqchip/gic-v3-its-platform-msi: Make of_device_ids const
irqchip/gic-v3-its: Make of_device_ids const
irqchip/irq-mvebu-icu: Add new driver for Marvell ICU
irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP
dt-bindings/interrupt-controller: Add DT binding for the Marvell ICU
genirq/irqdomain: Remove auto-recursive hierarchy support
irqchip/MSI: Use irq_domain_update_bus_token instead of an open coded access
...
- Potential out of bound access for GICv3
- Memory allocation gotcha in the Marvell GICP driver
- Fix openrisc interrupt acknowledgement
-----BEGIN PGP SIGNATURE-----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=sOY7
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Merge second batch of irqchip updates for 4.13 from Marc Zyngier
- Potential out of bound access for GICv3
- Memory allocation gotcha in the Marvell GICP driver
- Fix openrisc interrupt acknowledgement
Usually, hardware implicitly acknowledges interrupts when
reading them. However, if this is not the case, the IRQ
gets fired over and over again in the current implementation.
This patch uses the right mask acknowledge function to handle the
aforementioned situation on or1k processors that interact with
such kind of hardware.
Acked-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Pedro H. Penna <pedrohenriquepenna@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
BITS_TO_LONGS() gives us the number of longs we need, but we want to
allocate the number of bytes.
Fixes: a68a63cb4d ("irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP")
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- support for the new Marvell wire-to-MSI bridge
- support for the Aspeed I2C irqchip
- Armada XP370 per-cpu interrupt fixes
- GICv3 ITS ACPI NUMA support
- sunxi-nmi cleanup and updates for new platform support
- various GICv3 ITS cleanups and fixes
- some constifying in various places
-----BEGIN PGP SIGNATURE-----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=CAfw
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates for v4.13 from Marc Zyngier
- support for the new Marvell wire-to-MSI bridge
- support for the Aspeed I2C irqchip
- Armada XP370 per-cpu interrupt fixes
- GICv3 ITS ACPI NUMA support
- sunxi-nmi cleanup and updates for new platform support
- various GICv3 ITS cleanups and fixes
- some constifying in various places
The current ITS driver is assuming every ITS hardware implementation
supports minimum of 16bit INTID. But this is not true, as per GICv3
specification, INTID field is IMPLEMENTATION DEFINED in the range of
14-24 bits. We might see an unpredictable system behavior on systems
where hardware support less than 16bits and software tries to use
64K LPI interrupts.
On Qualcomm Datacenter Technologies QDF2400 platform, boot log shows
confusing information about number of LPI chunks as shown below. The
QDF2400 ITS hardware supports 24bit INTID.
This patch allocates the memory resources for PEND/PROP tables based
on discoverable value which is specified in GITS_TYPER.IDbits. Also
it fixes the log message that reflects the correct number of LPI
chunks were allocated.
ITS@0xff7efe0000: allocated 524288 Devices @3c0400000 (indirect, esz 8, psz 64K, shr 1)
ITS@0xff7efe0000: allocated 8192 Interrupt Collections @3c0130000 (flat, esz 8, psz 64K, shr 1)
ITS@0xff7efe0000: allocated 8192 Virtual CPUs @3c0140000 (flat, esz 8, psz 64K, shr 1)
ITS: Allocated 524032 chunks for LPIs
PCI/MSI: ITS@0xff7efe0000 domain created
Platform MSI: ITS@0xff7efe0000 domain created
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add code to parse SRAT ITS Affinity sub table as defined in ACPI 6.2.
Later in per device probe, ITS devices are mapped to numa node using
ITS Id to proximity domain mapping.
[maz: fix dependency on ACPICA, fixed structure name, minor cleanups]
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Marvell ICU unit is found in the CP110 block of the Marvell Armada
7K and 8K SoCs. It collects the wired interrupts of the devices located
in the CP110 and turns them into SPI interrupts in the GIC located in
the AP806 side of the SoC, by using a memory transaction.
Until now, the ICU was configured in a static fashion by the firmware,
and Linux was relying on this static configuration. By having Linux
configure the ICU, we are more flexible, and we can allocate dynamically
the GIC SPI interrupts only for devices that are actually in use.
The driver was initially written by Hanna Hawa <hannah@marvell.com>.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This commit adds a simple driver for the Marvell GICP, a hardware unit
that converts memory writes into GIC SPI interrupts. The driver provides
a number of functions to the ICU driver to allocate GICP interrupts, and
get the physical addresses that the ICUs should write to to set/clear
interrupts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we have irq_domain_update_bus_token(), switch everyone over
to it. The debugfs code thanks you for your continued support.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the builtin_platform_driver() macro to make the code simpler.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Aspeed 24XX/25XX chips share a single hardware interrupt across 14
separate I2C busses. This adds a dummy irqchip which maps the single
hardware interrupt to software interrupts for each of the busses.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In addition to introducing the new compatible string the bindings
description is reworked to be more generic.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This reverts commit 353d6d6c82, which is
no longer needed, now that the irq-armada-370-xp driver properly
re-enables per-CPU interrupt on both the boot CPU and secondary CPUs
after resume.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit d17cab4451 ("irqchip: Kill off set_irq_flags usage") changed
the code of armada_370_xp_mpic_irq_map() from using set_irq_flags() to
irq_set_probe().
While the commit log seems to imply that there are no functional
changes, there are indeed functional changes introduced by this commit:
the IRQ_NOAUTOEN flag is no longer cleared. This functional change
caused a regression on Armada XP, which no longer works properly after
suspend/resume because per-CPU interrupts remain disabled. This
regression was temporarly worked around in commit
353d6d6c82 ("irqchip/armada-370-xp: Fix regression by clearing
IRQ_NOAUTOEN"), but it is not the most satisfying solution. This commit
implements the solution that was initially discussed with Thomas
Gleixner.
Due to how the hardware registers work, the irq-armada-370-xp cannot
simply save/restore a bunch of registers at suspend/resume to make sure
that the interrupts remain in the same state after resuming. Therefore,
it relies on the kernel to say whether the interrupt is disabled or not,
using the irqd_irq_disabled() function. This was all working fine while
the IRQ_NOAUTOEN flag was cleared.
With the change introduced by Rob Herring in d17cab4451, the
IRQ_NOAUTOEN flag is now set for all interrupts. irqd_irq_disabled()
returns false for per-CPU interrupts, and therefore our per-CPU
interrupts are no longer re-enabled after resume.
This commit fixes that by using irqd_irq_disabled() only for global
interrupts, and using the newly introduced irq_percpu_is_enabled() for
per-CPU interrupts.
Also, it fixes a related problems that per-CPU interrupts were only
re-enabled on the boot CPU and not other CPUs. Until now this wasn't a
problem since on this platform, only the local timers are using per-CPU
interrupts and the local timers of secondary CPUs are turned off/on
during CPU hotplug before suspend, after after resume. However, since
Linux 4.4, we are also be using per-CPU interrupts for the network
controller, so we need to properly restore the per-CPU interrupts on
secondary CPUs as well.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since the overall logic of the driver to handle the global and per-CPU
masking of the interrupts is far from trivial, this commit adds a long
comment detailing how the hardware operates and what strategy the
driver implements on top of that.
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to clarify to which register base the various register
definitions apply, this commit re-orders them, and adds a comment that
clearly indicate which registers are relative to "main_int_base" and
which registers are relative to "per_cpu_int_base".
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Just skip the irq affinity setting when the target cpu is the same as
current setting.
This is a small optimization for irq affinity setting logic.
Signed-off-by: MaJun <majun258@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The call to pci_for_each_dma_alias() in the ITS PCI code has aroused
suspicion in the past, and upon closer inspection does turn out to be
completely backwards. Rather than iterating through each RID alias of
the given device, what we actually want to be doing here is iterating
through all the *other* devices which may also alias the same RID, in
order to size the table for the worst case.
Do the right thing by ignoring the initial DMA aliases themselves and
just using that walk to detect an aliasing bridge, then walking back
down the bus topology as necessary to actually count everything else.
Our alias handling still isn't perfect, since we don't account for the
cases of certain bridges only taking ownership of transactions under
particular circumstances, but without completely reworking the ITS code
to cope with the notion of multiple DevIDs per device, it'll have to do.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The R_INTC on the A31 is undocumented. It was previously supported
by the sun6i-a31-sc-nmi compatible. This compatible however required
the register region to start at the first used register, rather than
the boundaries laid out in the SoC's memory map. The new compatible
fixes the alignment, while also naming it properly.
Since the only difference between the old and new compatibles are
a fixed offset for the registers, and since the old one is deprecated,
this patch adds a set of register defines for the new compatible,
while modifying the old set to reference the new set minus a fixed
offset.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The sunxi_sc_nmi_reg_offs, which hold the register offsets for the
various variants, is never modified, and only used at init time within
the init functions referenced by IRQCHIP_DECLARE, which themselves are
tagged __init.
Const-ify the sunxi_sc_nmi_reg_offs structures, and tag them as
__initconst.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This is a pure code move to reorder the various sunxi_sc_nmi_reg_offs'
by family and alphabetical order. No functionality changes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The sunxi-nmi disables all its interrupts and clears any pending
interrupts at probe time.
Add comments documenting it, just to make it clear.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The sunxi-nmi driver has a bunch of raw register offsets and bit values.
Convert them into define macros for better readability.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
gic_read_count(), gic_write_compare() and gic_write_cpu_compare() are
often used in a sequence to update the compare register with a count
value increased by a small offset.
With small delta values used to update the compare register, the time to
update function trace for these operations may be longer than the update
timeout leading to update failure.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1496991845-27031-1-git-send-email-marcin.nowakowski@imgtec.com
ACPI IORT is an ACPI addendum to describe the connection topology of
devices with IOMMUs and interrupt controllers on ARM64 ACPI systems.
Currently the ACPI IORT Kbuild symbol is selected whenever the Kbuild
symbol ARM_GIC_V3_ITS is enabled, which in turn is selected by ARM64
Kbuild defaults. This makes the logic behind ACPI_IORT selection a bit
twisted and not easy to follow. On ARM64 systems enabling ACPI the
kbuild symbol ACPI_IORT should always be selected in that it is a kernel
layer provided to the ARM64 arch code to parse and enable ACPI firmware
bindings.
Make the ACPI_IORT selection explicit in ARM64 Kbuild and remove the
selection from ARM_GIC_V3_ITS entry, making the ACPI_IORT selection
logic clearer to follow.
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- don't use linux IRQ #0 in legacy irq domains: fixes timer interrupt
assignment when it's hardware IRQ # is 0 and the kernel is built w/o
device tree support;
- reduce reservation size for double exception vector literals from 48
to 20 bytes: fixes build on cores with small user exception vector;
- cleanups: use kmalloc_array instead of kmalloc in simdisk_init and
seq_puts instead of seq_printf in c_show.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5lPB
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20170612' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa fixes from Max Filippov:
- don't use linux IRQ #0 in legacy irq domains: fixes timer interrupt
assignment when it's hardware IRQ # is 0 and the kernel is built w/o
device tree support
- reduce reservation size for double exception vector literals from 48
to 20 bytes: fixes build on cores with small user exception vector
- cleanups: use kmalloc_array instead of kmalloc in simdisk_init and
seq_puts instead of seq_printf in c_show.
* tag 'xtensa-20170612' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: don't use linux IRQ #0
xtensa: reduce double exception literal reservation
xtensa: ISS: Use kmalloc_array() in simdisk_init()
xtensa: Use seq_puts() in c_show()
Linux IRQ #0 is reserved for error reporting and may not be used.
Increase NR_IRQS for one additional slot and increase
irq_domain_add_legacy parameter first_irq value to 1, so that linux
IRQ #0 is not associated with hardware IRQ #0 in legacy IRQ domains.
Introduce macro XTENSA_PIC_LINUX_IRQ for static translation of xtensa
PIC hardware IRQ # to linux IRQ #. Use this macro in XTFPGA platform
data definitions.
This fixes inability to use hardware IRQ #0 in configurations that don't
use device tree and allows for non-identity mapping between linux IRQ #
and hardware IRQ #.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Pull irq fixes from Thomas Gleixner:
"A set of small fixes for the irq subsystem:
- Cure a data ordering problem with chained interrupts
- Three small fixlets for the mbigen irq chip"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix chained interrupt data ordering
irqchip/mbigen: Fix the clear register offset calculation
irqchip/mbigen: Fix potential NULL dereferencing
irqchip/mbigen: Fix memory mapping code
The register array offset for clearing an interrupt is calculated by:
offset = (hwirq - RESERVED_IRQ_PER_MBIGEN_CHIP) / 32;
This is wrong because the clear register array includes the reserved
interrupts. So the clear operation ends up in the wrong register.
This went unnoticed so far, because the hardware clears the real bit
through a timeout mechanism when the hardware is configured in debug
mode. That debug mode was enabled on early generations of the hardware, so
the problem was papered over.
On newer hardware with updated firmware the debug mode was disabled, so the
bits did not get cleared which causes the system to malfunction.
Remove the subtraction of RESERVED_IRQ_PER_MBIGEN_CHIP, so the correct
register is accessed.
[ tglx: Rewrote changelog ]
Fixes: a6c2f87b88 ("irqchip/mbigen: Implement the mbigen irq chip operation functions")
Signed-off-by: MaJun <majun258@huawei.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: linuxarm@huawei.com
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Link: http://lkml.kernel.org/r/1494561328-39514-4-git-send-email-guohanjun@huawei.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some mbigens share memory regions, and devm_ioremap_resource
does not allow to share resources which will break the probe
of mbigen, in opposition to devm_ioremap.
This patch restores back usage of devm_ioremap function, but
with proper error handling and logging.
Fixes: 216646e4d8 ("irqchip/mbigen: Fix return value check in mbigen_device_probe()")
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: linuxarm@huawei.com
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: MaJun <majun258@huawei.com>
Link: http://lkml.kernel.org/r/1494561328-39514-2-git-send-email-guohanjun@huawei.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). Use devm_ioremap_resource() instead of devm_ioremap()
to fix the IS_ERR() test issue.
Fixes: 76e1f77f9c ("irqchip/mbigen: Introduce mbigen_of_create_domain()")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/20170427152113.31147-1-weiyj.lk@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 4cfffcfa51 ("irqchip/mips-gic: Fix local interrupts") fixed
local interrupts by creating virq mappings for them all at startup.
Unfortunately this change broke legacy IRQ controllers in the same
system, such as the i8259 on the Malta platform, as it allocates virq
numbers that were expected to be available for the legacy controller.
Instead of creating the mappings statically when the GIC is probed,
re-introduce the irq domain .map function, removed by commit e875bd66df
("irqchip/mips-gic: Fix local interrupts") and use it to set up the irq
handler and chip. Since a good deal of the required functionality is
already implemented by gic_irq_domain_alloc, repurpose that function for
gic_irq_domain_map and add a new gic_irq_domain_alloc which wraps
gic_irq_domain_map with the necessary conversion.
This change fixes the legacy interrupt controller of the Malta platform
without breaking the perf interrupt fixed by commit e875bd66df
("irqchip/mips-gic: Fix local interrupts").
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1492679256-14513-4-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In commit c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Qais indicates that he felt having a separate device IRQ domain was
cleaner, but along with everyone else I'm aware of touching this driver
I disagree.
Remove the separate device IRQ domain so that we simply have the main
GIC IRQ domain used for devices, and an IPI IRQ domain as a child. The
logic for handling the device interrupts & IPIs is cleanly separated
into the appropriate domain ops, making it much easier to reason about
what the driver is doing than the previous approach where the 2 child
domains had to call up to their parent, which had to handle both types
of interrupt & had all sorts of weird & wonderful duplication or
outright clobbering of setup performed by multiple domains.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1492679256-14513-3-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since commit 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy
domain") introduced the GIC IPI IRQ domain we have tracked both
reservation of interrupts & their use with a single bitmap - ipi_resrv.
If an interrupt is reserved for use as an IPI but not actually in use
then the appropriate bit is set in ipi_resrv. If an interrupt is either
not reserved for use as an IPI or has been allocated as one then the
appropriate bit is clear in ipi_resrv.
Unfortunately this means that checking whether a bit is set in ipi_resrv
to prevent IPI interrupts being allocated for use with a device is
broken, because if the interrupt has been allocated as an IPI first then
its bit will be clear.
Fix this by separating the tracking of IPI reservation & usage,
introducing a separate ipi_available bitmap for the latter. This means
that ipi_resrv will now always have bits set corresponding to all
interrupts reserved for use as IPIs, whether or not they have been
allocated yet, and therefore that checking it when allocating device
interrupts works as expected.
Fixes: 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1492679256-14513-2-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Introduce support for registering an IPI IRQ domain suitable for use by
systems using the MIPS MT (multithreading) ASE within a single core.
This will allow for such systems to be supported generically, without
the current kludge of IPI code split between the MIPS arch & the malta
board support code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15836/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The various struct irq_chip callbacks in the MIPS CPU interrupt
controller driver have been calculating the hardware interrupt number by
subtracting MIPS_CPU_IRQ_BASE from the virq number. This presumes a
linear mapping beginning from MIPS_CPU_IRQ_BASE, and this will not hold
once an IPI IRQ domain is introduced. Switch to using the hwirq field of
struct irq_data which already contains the hardware interrupt number
instead of attempting to calculate it.
Similarly, plat_irq_dispatch calculated the virq number by adding
MIPS_CPU_IRQ_BASE to the hardware interrupt number. Ready this for the
introduction of an IPI IRQ domain by instead using irq_linear_revmap.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15835/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace use of the magic number 0x100 (ie. bit 8) with the more
explanatory IE_SW0 (ie. interrupt enable for software interrupt 0) or
C_SW0 (ie. cause bit for software interrupt 0) as appropriate.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15834/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Clear OF_POPULATED flag, so that GPC power domain driver[1] can be
bound to "gpc" node as well.
[1] https://lkml.org/lkml/2017/3/28/835
Cc: yurovsky@gmail.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On sama5d2, VDD core may be cut while suspending to RAM. This means the
AIC5 registers content is lost. Restore it at resume time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In Mediatek SOCs, the CIRQ is a low power interrupt controller
designed to works outside MCUSYS which comprises with Cortex-Ax
cores,CCI and GIC.
The CIRQ controller is integrated in between MCUSYS( include
Cortex-Ax, CCI and GIC ) and interrupt sources as the second
level interrupt controller. The external interrupts which outside
MCUSYS will feed through CIRQ then bypass to GIC. CIRQ can monitors
all edge trigger interupts. When an edge interrupt is triggered,
CIRQ can record the status and generate a pulse signal to GIC when
flush command executed.
When system enters sleep mode, MCUSYS will be turned off to improve
power consumption, also GIC is power down. The edge trigger interrupts
will be lost in this scenario without CIRQ.
This commit provides the CIRQ irqchip implement.
Signed-off-by: Youlin Pei <youlin.pei@mediatek.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Getting hold of the DevID requires us to call iort_pmsi_get_dev_id().
Since iort_pmsi_get_dev_id() may or may not be implemented, we
provide a weak function that acts as a stub.
The weak function will be removed when the ACPI counterpart is
merged.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
With the preparation of platform msi support and interrupt producer
in commit d44fa3d460 ("ACPI: Add support for ResourceSource/IRQ
domain mapping"), we can add mbigen ACPI support now.
Now that the major framework changes are ready, we just need to add
the ACPI probe code which creates the irqdomain for devices connecting
to it.
In order to create the irqdomain, we need to know the number of hw
irqs as input which is provided by mbigen. In DT case, we are using
"num-pins" property to describe it, and we will take advantage of
that too using _DSD in ACPI as there is no standard way of describe
it in ACPI way, also according to the _DSD rule described in
Documentation/acpi/DSD-properties-rules.txt, it doesn't break
the rules.
The DSDT is represented as below:
For mbigen,
Device(MBI0) {
Name(_HID, "HISI0152")
Name(_UID, Zero)
Name(_CRS, ResourceTemplate() {
Memory32Fixed(ReadWrite, 0xa0080000, 0x10000)
})
Name(_DSD, Package () {
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {"num-pins", 378}
}
})
}
For devices,
Device(SAS0) {
Name(_HID, "HISIxxxx")
Name(_UID, Zero)
Name(_CRS, ResourceTemplate() {
Memory32Fixed(ReadWrite, 0xb0030000, 0x10000)
Interrupt(ResourceConsumer,..., "\_SB.MBI0") {12, ...}
})
}
So for the devices connected to the mbigen, as we clearly say that
it refers to a specific interrupt controller (mbigen), we can get
the virq from mbigen's irqdomain once it's created successfully.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: MaJun <majun258@huawei.com>
Cc: Al Stone <ahs3@redhat.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce mbigen_of_create_domain() to consolidate OF related
code and prepare for ACPI later, no funtional change.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Ma Jun <majun258@huawei.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Module owner will be set by driver core, so drop it.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Ma Jun <majun258@huawei.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
With the introduction of its_pmsi_init_one(), support for ACPI
firmware interface can be plugged into the gicv3 ITS driver.
Add code to scan the MADT table to get the ITS entry(ies), then use
the information to create the platform msi domain for devices
connected to it, mirroring the ITS PCI MSI code path.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce its_pmsi_init_one() to separate firmware dependent
code (ie OF dependent code) and firmware agnostic code so
that gic3-its code can be made to support other firmware
bindings easily.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
By adding ACPI support for platform MSI, the gicv3 driver has to
provide code to retrieve the dev id through ACPI instead of device
tree bindings; given that its_pmsi_prepare() allows already to get
the dev id but it is OF dependent, factor OF related code out into
a single function to make its_pmsi_prepare() ready to be used with
other firmware interfaces.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Rearrange header file includes in alphabetic order.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: fixed commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This prevent unnecessary visibility when configuring trigger type
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Originally driver only supports one base. However, MT6797 has
more than one bases to configure interrupt polarity. To support
possible design change, here comes a solution to use arbitrary
number of bases.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Moxa Art interrupt controller is very very likely just an instance
of the Faraday FTINTC010 interrupt controller from Faraday Technology.
An indication would be its close association with the FA526 ARM core
and the fact that the register layout is the same.
The implementation in irq-moxart.c can probably be right off replaced
with the irq-ftintc010.c driver by adding a compatible string, selecting
this irqchip from the machine and run.
As a bonus we have an irqchip driver supporting high/low and
rising/falling edges for the Moxa Art, and shared code with the Gemini
platform.
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The triggers in the driver were right for high level triggered
IRQs but the edge detection on edge triggered IRQs was wrong.
After studying a proper driver from Po-Yu Chuang I now know how
to handle these right, and we can properly implement low level
IRQs as well.
The device trees for the Gemini had polarity switched around
so these have been fixed to conform to the right polarity as
well.
Cc: Greentime Hu <green.hu@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Gemini irqchip turns out to be a standard IP component from
Faraday Technology named FTINTC010 after some research and new
information.
- Rename the driver and all symbols to reflect the new information.
- Add the new compatible string "faraday,ftintc010"
- Create a Kconfig symbol CONFIG_FARADAY_FTINTC010 so that SoCs
using this interrupt controller can easily select and reuse it
instead of hardwiring it to ARCH_GEMINI
I have created a separate patch to select the new Kconfig symbol
from the Gemini machine, which will be merged through the ARM
SoC tree.
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit 4cfffcfa51 ("irqchip/mips-gic: Fix local interrupts") added
mapping of several local interrupts during initialisation of the gic
driver. This associates virq numbers with these interrupts.
Unfortunately, as not all of the interrupts are mapped in hardware
order, when drivers subsequently request these interrupts they conflict
with the mappings that have already been set up. For example, this
manifests itself in the gic clocksource driver, which fails to probe
with the message:
clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0x7350c9738,
max_idle_ns: 440795203769 ns
GIC timer IRQ 25 setup failed: -22
This is because virq 25 (the correct IRQ number specified via device
tree) was allocated to the PERFCTR interrupt (and 24 to the timer, 26 to
the FDC). To fix this, map all of these local interrupts in the hardware
order so as to associate their virq numbers with the correct hw
interrupts.
Fixes: 4cfffcfa51 ("irqchip/mips-gic: Fix local interrupts")
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This driver uses the MSI domain but has no strict dependency on PCI_MSI, so we
may run into a build failure when CONFIG_GENERIC_MSI_IRQ_DOMAIN is disabled:
drivers/irqchip/irq-mvebu-odmi.c:152:15: error: variable 'odmi_msi_ops' has initializer but incomplete type
static struct msi_domain_ops odmi_msi_ops = {
^~~~~~~~~~~~~~
drivers/irqchip/irq-mvebu-odmi.c:155:15: error: variable 'odmi_msi_domain_info' has initializer but incomplete type
static struct msi_domain_info odmi_msi_domain_info = {
^~~~~~~~~~~~~~~
drivers/irqchip/irq-mvebu-odmi.c:156:3: error: 'struct msi_domain_info' has no member named 'flags'
.flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS),
^~~~~
drivers/irqchip/irq-mvebu-odmi.c:156:12: error: 'MSI_FLAG_USE_DEF_DOM_OPS' undeclared here (not in a function)
.flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS),
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/irqchip/irq-mvebu-odmi.c:156:39: error: 'MSI_FLAG_USE_DEF_CHIP_OPS' undeclared here (not in a function); did you mean 'MSI_FLAG_USE_DEF_DOM_OPS'?
Selecting the option from this driver seems to solve this nicely, though I could
not find any other instance of this in irqchip drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- irqchip/crossbar: Some type tidying up
- irqchip/gicv3-its: Workaround for a Qualcomm erratum
- irqdomain: Compile for for systems that don't use CONFIG_IRQ_DOMAIN
-----BEGIN PGP SIGNATURE-----
iQFJBAABCAAzFiEEaVjJ8iM8Xp1syoGKqzCcdLk7HqEFAljBLCQVHG1hcmMuenlu
Z2llckBhcm0uY29tAAoJEKswnHS5Ox6h6h8IAJKt0NHSLV4vQH51MdX1flj8uyw0
xzeosx/r7hsV/apbaFcciJuaOZNDYdVH+a1NboklpDe2g8N1eSwSITodXnsg3seO
1EyGWkZT9lWbz8/febvG8WPLLZJu0CeD9wNRT7cePTUgNZgGRR1IN6ySM/TtWixA
csIL9kgdRvChcU6hydTPceBzN5pSpZ169+BTeEL5CVTggRiq24fJlmBwM7caOu1Z
nZDsKckUQA5D/VO0CiopE6BpCZTBzB6TTC2251DEEfVxyL6/M947lOtsC4EXK4y2
6CjWM4II24ImvPmqYDNIwzK1ZimhWO0Uo8jy1LZZKVpiXXXk8zm6LKxqJbU=
=JV9b
-----END PGP SIGNATURE-----
Merge tag 'irq-fixes-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip/irqdomain updates for 4.11-rc2 from Marc Zyngier
- irqchip/crossbar: Some type tidying up
- irqchip/gicv3-its: Workaround for a Qualcomm erratum
- irqdomain: Compile for for systems that don't use CONFIG_IRQ_DOMAIN
Fixed up minor conflict in the crossbar driver.
The 'size' variable is unsigned according to the dt-bindings.
As this variable is used as integer in other places, create a new variable
that allows to fix the following sparse issue (-Wtypesign):
drivers/irqchip/irq-crossbar.c:279:52: warning: incorrect type in argument 3 (different signedness)
drivers/irqchip/irq-crossbar.c:279:52: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:279:52: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On Qualcomm Datacenter Technologies QDF2400 SoCs, the ITS hardware
implementation uses 16Bytes for Interrupt Translation Entry (ITE),
but reports an incorrect value of 8Bytes in GITS_TYPER.ITTE_size.
It might cause kernel memory corruption depending on the number
of MSI(x) that are configured and the amount of memory that has
been allocated for ITEs in its_create_device().
This patch fixes the potential memory corruption by setting the
correct ITE size to 16Bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The max and entry variables are unsigned according to the dt-bindings.
Fix following 3 sparse issues (-Wtypesign):
drivers/irqchip/irq-crossbar.c:222:52: warning: incorrect type in argument 3 (different signedness)
drivers/irqchip/irq-crossbar.c:222:52: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:222:52: got int *<noident>
drivers/irqchip/irq-crossbar.c:245:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:245:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:245:56: got int *<noident>
drivers/irqchip/irq-crossbar.c:263:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:263:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:263:56: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The max and entry variables are unsigned according to the dt-bindings.
Fix following 3 sparse issues (-Wtypesign):
drivers/irqchip/irq-crossbar.c:222:52: warning: incorrect type in argument 3 (different signedness)
drivers/irqchip/irq-crossbar.c:222:52: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:222:52: got int *<noident>
drivers/irqchip/irq-crossbar.c:245:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:245:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:245:56: got int *<noident>
drivers/irqchip/irq-crossbar.c:263:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:263:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:263:56: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Cc: marc.zyngier@arm.com
Cc: jason@lakedaemon.net
Link: http://lkml.kernel.org/r/20170223094855.6546-1-fdemathieu@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The changes include:
* KVM PCIe/MSI passthrough support on ARM/ARM64
* Introduction of a core representation for individual hardware
iommus
* Support for IOMMU privileged mappings as supported by some
ARM IOMMUS
* 16-bit SID support for ARM-SMMUv2
* Stream table optimization for ARM-SMMUv3
* Various fixes and other small improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5b3I
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU UPDATES from Joerg Roedel:
- KVM PCIe/MSI passthrough support on ARM/ARM64
- introduction of a core representation for individual hardware iommus
- support for IOMMU privileged mappings as supported by some ARM IOMMUS
- 16-bit SID support for ARM-SMMUv2
- stream table optimization for ARM-SMMUv3
- various fixes and other small improvements
* tag 'iommu-updates-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (61 commits)
vfio/type1: Fix error return code in vfio_iommu_type1_attach_group()
iommu: Remove iommu_register_instance interface
iommu/exynos: Make use of iommu_device_register interface
iommu/mediatek: Make use of iommu_device_register interface
iommu/msm: Make use of iommu_device_register interface
iommu/arm-smmu: Make use of the iommu_register interface
iommu: Add iommu_device_set_fwnode() interface
iommu: Make iommu_device_link/unlink take a struct iommu_device
iommu: Add sysfs bindings for struct iommu_device
iommu: Introduce new 'struct iommu_device'
iommu: Rename struct iommu_device
iommu: Rename iommu_get_instance()
iommu: Fix static checker warning in iommu_insert_device_resv_regions
iommu: Avoid unnecessary assignment of dev->iommu_fwspec
iommu/mediatek: Remove bogus 'select' statements
iommu/dma: Remove bogus dma_supported() implementation
iommu/ipmmu-vmsa: Restrict IOMMU Domain Geometry to 32-bit address space
iommu/vt-d: Don't over-free page table directories
iommu/vt-d: Tylersburg isoch identity map check is done too late.
iommu/vt-d: Fix some macros that are incorrectly specified in intel-iommu
...
Pull irq updates from Thomas Gleixner:
"This update provides:
- Yet another two irq controller chip drivers
- A few updates and fixes for GICV3
- A resource managed function for interrupt allocation
- Fixes, updates and enhancements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/qcom: Fix error handling
genirq: Clarify logic calculating bogus irqreturn_t values
genirq/msi: Add stubs for get_cached_msi_msg/pci_write_msi_msg
genirq/devres: Use dev_name(dev) as default for devname
genirq: Fix /proc/interrupts output alignment
irqdesc: Add a resource managed version of irq_alloc_descs()
irqchip/gic-v3-its: Zero command on allocation
irqchip/gic-v3-its: Fix command buffer allocation
irqchip/mips-gic: Fix local interrupts
irqchip: Add a driver for Cortina Gemini
irqchip: DT bindings for Cortina Gemini irqchip
irqchip/gic-v3: Remove duplicate definition of GICD_TYPER_LPIS
irqchip/gic-v3-its: Rename MAPVI to MAPTI
irqchip/gic-v3-its: Drop deprecated GITS_BASER_TYPE_CPU
irqchip/gic-v3-its: Refactor command encoding
irqchip/gic-v3-its: Enable cacheable attribute Read-allocate hints
irqchip/qcom: Add IRQ combiner driver
ACPI: Add support for ResourceSource/IRQ domain mapping
ACPI: Generic GSI: Do not attempt to map non-GSI IRQs during bus scan
irq/platform-msi: Fix comment about maximal MSIs
When reusing commands from the ring buffer, it would be better
to zero them out, even if the ITS should ignore the unused
fields.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The its command buffer must be page aligned, but kzalloc() is not
guaranteed to be (though it is mostly when allocating 64k). Use
__get_free_pages() as this is used for other buffers as well.
Signed-off-by: Robert Richter <rrichter@cavium.com>
[Marc: fixed the error path]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Some local interrupts are not initialised properly at the moment and
cannot be used since the domain's alloc method is never called for them.
This has been observed earlier and partially fixed in commit
e875bd66df ("irqchip/mips-gic: Fix local interrupts"), but that change
still relied on the interrupt to be requested by an external driver (eg.
drivers/clocksource/mips-gic-timer.c).
This does however not solve the issue for interrupts that are not
referenced by any driver through the device tree and results in
request_irq() calls returning -ENOSYS. It can be observed when attempting
to use perf tool to access hardware performance counters.
Fix this by explicitly calling irq_create_fwspec_mapping() for local
interrupts.
Fixes: e875bd66df ("irqchip/mips-gic: Fix local interrupts")
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As a part of transitioning the Gemini platform to device tree we
create this clean, device-tree-only irqchip driver.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Back in the days when the GICv3/v4 architecture was drafted,
the command to an event to an LPI number was called MAPVI.
Later on, and to avoid confusion with the GICv4 command VMAPI,
it was renamed MAPTI. We've carried the old name for a long
time, but it gets in the way of people reading the code in
the light of the public architecture specification.
Just repaint all the references and kill the old definition.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
During the development of the GICv3/v4 architecture, it was
envisaged to have a CPU table, though the use for it was
never completely clear (the collection table serves that role
pretty well). It ended being dropped before the specification
was published, though it lived on in the driver.
In order to avoid people scratching their head too much, let's do
the same in the kernel.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The way we encode the various ITS command fields is both tedious
and error prone. Let's introduce a helper function that performs
the encoding, and convert the existing encoders to use that
helper. It also has the advantage of expressing the encoding in
a way that matches the architecture specification.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Read-allocation hints are not enabled for both the GIC-ITS and GICR
tables. This forces the hardware to always read the table contents
from an external memory (DDR) which is slow compared to cache memory.
Most of the tables are often read by hardware. So, it's better to
enable Read-allocate hints in addition to Write-allocate hints in
order to improve the GICR_PEND, GICR_PROP, Collection, Device, and
vCPU tables lookup time.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Driver for interrupt combiners in the Top-level Control and Status
Registers (TCSR) hardware block in Qualcomm Technologies chips.
An interrupt combiner in this block combines a set of interrupts by
OR'ing the individual interrupt signals into a summary interrupt
signal routed to a parent interrupt controller, and provides read-
only, 32-bit registers to query the status of individual interrupts.
The status bit for IRQ n is bit (n % 32) within register (n / 32)
of the given combiner. Thus, each combiner can be described as a set
of register offsets and the number of IRQs managed.
Signed-off-by: Agustin Vega-Frias <agustinv@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The GICv3 ITS is MSI remapping capable. Let's advertise
this property so that VFIO passthrough can assess IRQ safety.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ICOLL controller doesn't provide any facility to configure the
wakeup sources. That's the reason why this implementation lacks
the irq_set_wake implementation. But this prevent us from properly
entering power management states like "suspend to idle".
So enable the flags IRQCHIP_SKIP_SET_WAKE and
IRQCHIP_MASK_ON_SUSPEND to let the irqchip core allows and handles
the power management.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Link: https://lkml.kernel.org/r/1482863397-11400-1-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The below call chain generates "scheduling while atomic" backtrace and
causes system crash when Keystone 2 IRQ chip driver is used with RT-kernel:
gic_handle_irq()
|-__handle_domain_irq()
|-generic_handle_irq()
|-keystone_irq_handler()
|-regmap_read()
|-regmap_lock_spinlock()
|-rt_spin_lock()
The reason is that Keystone driver dispatches IRQ using chained IRQ handler
and accesses I/O memory through syscon->regmap(mmio) which is implemented
as fast_io regmap and uses regular spinlocks for synchronization, but
spinlocks transformed to rt_mutexes on RT.
Hence, convert Keystone 2 IRQ driver to use generic irq handler instead of
chained IRQ handler. This way it will be compatible with RT kernel where it
will be forced thread IRQ handler while in non-RT kernel it still will be
executed in HW IRQ context.
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Suman Anna <s-anna@ti.com>
Link: https://lkml.kernel.org/r/20161208233310.10329-1-grygorii.strashko@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
The mpic is either the main interrupt controller or is cascaded behind a
GIC. The mpic is single instance and the modes are mutually exclusive, so
there is no reason to have seperate cpu hotplug states.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20161221192112.333161745@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Even if both drivers are compiled in only one instance can run on a given
system depending on the available GIC version.
So having seperate hotplug states for them is pointless.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.252416267@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When CONFIG_PM_SLEEP is disabled, the compiler raises a warning on
st_irq_syscfg_resume:
drivers/irqchip/irq-st.c:183:12: warning: 'st_irq_syscfg_resume' defined
but not used [-Wunused-function]
static int st_irq_syscfg_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~
Annotate the function with __maybe_unused.
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/20161217002927.31947-1-jeremy.lefaure@lse.epita.fr
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- struct thread_info moved off-stack (also touching
include/linux/thread_info.h and include/linux/restart_block.h)
- cpus_have_cap() reworked to avoid __builtin_constant_p() for static
key use (also touching drivers/irqchip/irq-gic-v3.c)
- Uprobes support (currently only for native 64-bit tasks)
- Emulation of kernel Privileged Access Never (PAN) using TTBR0_EL1
switching to a reserved page table
- CPU capacity information passing via DT or sysfs (used by the
scheduler)
- Support for systems without FP/SIMD (IOW, kernel avoids touching these
registers; there is no soft-float ABI, nor kernel emulation for
AArch64 FP/SIMD)
- Handling of hardware watchpoint with unaligned addresses, varied
lengths and offsets from base
- Use of the page table contiguous hint for kernel mappings
- Hugetlb fixes for sizes involving the contiguous hint
- Remove unnecessary I-cache invalidation in flush_cache_range()
- CNTHCTL_EL2 access fix for CPUs with VHE support (ARMv8.1)
- Boot-time checks for writable+executable kernel mappings
- Simplify asm/opcodes.h and avoid including the 32-bit ARM counterpart
and make the arm64 kernel headers self-consistent (Xen headers patch
merged separately)
- Workaround for broken .inst support in certain binutils versions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Uk9
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- struct thread_info moved off-stack (also touching
include/linux/thread_info.h and include/linux/restart_block.h)
- cpus_have_cap() reworked to avoid __builtin_constant_p() for static
key use (also touching drivers/irqchip/irq-gic-v3.c)
- uprobes support (currently only for native 64-bit tasks)
- Emulation of kernel Privileged Access Never (PAN) using TTBR0_EL1
switching to a reserved page table
- CPU capacity information passing via DT or sysfs (used by the
scheduler)
- support for systems without FP/SIMD (IOW, kernel avoids touching
these registers; there is no soft-float ABI, nor kernel emulation for
AArch64 FP/SIMD)
- handling of hardware watchpoint with unaligned addresses, varied
lengths and offsets from base
- use of the page table contiguous hint for kernel mappings
- hugetlb fixes for sizes involving the contiguous hint
- remove unnecessary I-cache invalidation in flush_cache_range()
- CNTHCTL_EL2 access fix for CPUs with VHE support (ARMv8.1)
- boot-time checks for writable+executable kernel mappings
- simplify asm/opcodes.h and avoid including the 32-bit ARM counterpart
and make the arm64 kernel headers self-consistent (Xen headers patch
merged separately)
- Workaround for broken .inst support in certain binutils versions
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (60 commits)
arm64: Disable PAN on uaccess_enable()
arm64: Work around broken .inst when defective gas is detected
arm64: Add detection code for broken .inst support in binutils
arm64: Remove reference to asm/opcodes.h
arm64: Get rid of asm/opcodes.h
arm64: smp: Prevent raw_smp_processor_id() recursion
arm64: head.S: Fix CNTHCTL_EL2 access on VHE system
arm64: Remove I-cache invalidation from flush_cache_range()
arm64: Enable HIBERNATION in defconfig
arm64: Enable CONFIG_ARM64_SW_TTBR0_PAN
arm64: xen: Enable user access before a privcmd hvc call
arm64: Handle faults caused by inadvertent user access with PAN enabled
arm64: Disable TTBR0_EL1 during normal kernel execution
arm64: Introduce uaccess_{disable,enable} functionality based on TTBR0_EL1
arm64: Factor out TTBR0_EL1 post-update workaround into a specific asm macro
arm64: Factor out PAN enabling/disabling into separate uaccess_* macros
arm64: Update the synchronous external abort fault description
selftests: arm64: add test for unaligned/inexact watchpoint handling
arm64: Allow hw watchpoint of length 3,5,6 and 7
arm64: hw_breakpoint: Handle inexact watchpoint addresses
...
The Xilinx interrupt controller driver is now available in drivers/irqchip.
Switch to using that driver.
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The powerpc dts file does not have the xlnx,kind-of-intr property.
Instead of erroring out, give a warning instead. And attempt to
continue to probe the interrupt controller while assuming
kind-of-intr is 0x0 as a fall back.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The MIPS based xilfpga platform has the following IRQ structure
Peripherals --> xilinx_intcontroller -> mips_cpu_int controller
Add support for the driver to chain the irq handler
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that the driver is generic and used by multiple archs,
get_irq is too generic.
Rename get_irq to xintc_get_irq to avoid any conflicts
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a global structure to house various variables.
And cleanup read/write handling by using jump label api.
Tested-by; Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Remove __func__ and prefix irq-xilinx in various debug prints
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Xilinx AXI Interrupt Controller IP block is used by the MIPS
based xilfpga platform and a few PowerPC based platforms.
Move the interrupt controller code out of arch/microblaze so that
it can be used by everyone
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
readq and writeq type of assessors are not supported in AArch32, so we
need to specialise them and glue later with series of 32-bit accesses
on AArch32 side.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
It'd be better to switch to CMA... but before that done redirect
flush_dcache operation, so 32-bit implementation could be wired
latter.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
GITS_BASER<n>'s Entry Size is much smaller than 64-bit, but when it
used as a divider it forces compiler to generate __aeabi_uldivmod if
build in 32-bit mode. So, casting it to int (like it is done in other
places) where used as a divider would give a hint to compiler that
32-bit division can be used.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make sure that constants which are supposed to be applied on 64-bit
data is actually unsigned long long, so they won't be truncated when
used in 32-bit mode.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The hypervisor may not have full access to the kernel data structures
and hence cannot safely use cpus_have_cap() helper for checking the
system capability. Add a safe helper for hypervisors to check a constant
system capability, which *doesn't* fall back to checking the bitmap
maintained by the kernel. With this, make the cpus_have_cap() only
check the bitmask and force constant cap checks to use the new API
for quicker checks.
Cc: Robert Ritcher <rritcher@cavium.com>
Cc: Tirumalesh Chalamarla <tchalamarla@cavium.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Fix for 32bit accesses that should be 64bit on 64bit machines
- Fix for a field decoding macro
- Beautify a warning message
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DL0w
-----END PGP SIGNATURE-----
Merge tag 'gic-fixes-for-4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull GIC updates from Marc Zyngier:
- Fix for 32bit accesses that should be 64bit on 64bit machines
- Fix for a field decoding macro
- Beautify a warning message
Core drivers for J-Core SoCs will be selected implicitly via
CONFIG_SH_JCORE_SOC instead. Based on a corresponding change to the
clocksource/timer driver requested by Daniel Lezcano.
Signed-off-by: Rich Felker <dalias@libc.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-sh@vger.kernel.org
Link: http://lkml.kernel.org/r/883a3d17084003e3cf21bab73ec12828fe4ff6c6.1476899495.git.dalias@libc.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no need to have the 'struct irq_domain *nps400_root_domain'
variable static since new value is always assigned before use.
Fixes: 44df427c89 ("irqchip: add nps Internal and external irqchips")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1476714417-12095-1-git-send-email-weiyj.lk@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The GICv3 architecture specification mentions that a 64bit
register can be accessed using two 32bit accesses. What it
doesn't mention is that this is only guaranteed on a system
that implements AArch32, and a pure AArch64 system is allowed
not to support this. This causes issues with the GICR_TYPER
and GITS_TYPER registers, which are both RO 64bit registers.
In order to solve this, this patch switches the TYPER accesses
to the gic_read_typer macro already used in other parts of the
driver. This makes sure that we always use a 64bit access on
64bit systems, and two 32bit accesses on 32bit system.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull MIPS updates from Ralf Baechle:
"This is the main MIPS pull request for 4.9:
MIPS core arch code:
- traps: 64bit kernels should read CP0_EBase 64bit
- traps: Convert ebase to KSEG0
- c-r4k: Drop bc_wback_inv() from icache flush
- c-r4k: Split user/kernel flush_icache_range()
- cacheflush: Use __flush_icache_user_range()
- uprobes: Flush icache via kernel address
- KVM: Use __local_flush_icache_user_range()
- c-r4k: Fix flush_icache_range() for EVA
- Fix -mabi=64 build of vdso.lds
- VDSO: Drop duplicated -I*/-E* aflags
- tracing: move insn_has_delay_slot to a shared header
- tracing: disable uprobe/kprobe on compact branch instructions
- ptrace: Fix regs_return_value for kernel context
- Squash lines for simple wrapper functions
- Move identification of VP(E) into proc.c from smp-mt.c
- Add definitions of SYNC barrierstype values
- traps: Ensure full EBase is written
- tlb-r4k: If there are wired entries, don't use TLBINVF
- Sanitise coherentio semantics
- dma-default: Don't check hw_coherentio if device is non-coherent
- Support per-device DMA coherence
- Adjust MIPS64 CAC_BASE to reflect Config.K0
- Support generating Flattened Image Trees (.itb)
- generic: Introduce generic DT-based board support
- generic: Convert SEAD-3 to a generic board
- Enable hardened usercopy
- Don't specify STACKPROTECTOR in defconfigs
Octeon:
- Delete dead code and files across the platform.
- Change to use all memory into use by default.
- Rename upper case variables in setup code to lowercase.
- Delete legacy hack for broken bootloaders.
- Leave maintaining the link state to the actual ethernet/PHY drivers.
- Add DTS for D-Link DSR-500N.
- Fix PCI interrupt routing on D-Link DSR-500N.
Pistachio:
- Remove ANDROID_TIMED_OUTPUT from defconfig
TX39xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
TX49xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
txx9wdt:
- Add missing clock (un)prepare calls for CCF
BMIPS:
- Add PW, GPIO SDHCI and NAND device node names
- Support APPENDED_DTB
- Add missing bcm97435svmb to DT_NONE
- Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
- Add DT examples for BCM63268, BCM3368 and BCM6362
- Add support for BCM3368 and BCM6362
PCI
- Reduce stack frame usage
- Use struct list_head lists
- Support for CONFIG_PCI_DOMAINS_GENERIC
- Make pcibios_set_cache_line_size an initcall
- Inline pcibios_assign_all_busses
- Split pci.c into pci.c & pci-legacy.c
- Introduce CONFIG_PCI_DRIVERS_LEGACY
- Support generic drivers
CPC
- Convert bare 'unsigned' to 'unsigned int'
- Avoid lock when MIPS CM >= 3 is present
GIC:
- Delete unused file smp-gic.c
mt7620:
- Delete unnecessary assignment for the field "owner" from PCI
BCM63xx:
- Let clk_disable() return immediately if clk is NULL
pm-cps:
- Change FSB workaround to CPU blacklist
- Update comments on barrier instructions
- Use MIPS standard lightweight ordering barrier
- Use MIPS standard completion barrier
- Remove selection of sync types
- Add MIPSr6 CPU support
- Support CM3 changes to Coherence Enable Register
SMP:
- Wrap call to mips_cpc_lock_other in mips_cm_lock_other
- Introduce mechanism for freeing and allocating IPIs
cpuidle:
- cpuidle-cps: Enable use with MIPSr6 CPUs.
SEAD3:
- Rewrite to use DT and generic kernel feature.
USB:
- host: ehci-sead3: Remove SEAD-3 EHCI code
FBDEV:
- cobalt_lcdfb: Drop SEAD3 support
dt-bindings:
- Document a binding for simple ASCII LCDs
auxdisplay:
- img-ascii-lcd: driver for simple ASCII LCD displays
irqchip i8259:
- i8259: Add domain before mapping parent irq
- i8259: Allow platforms to override poll function
- i8259: Remove unused i8259A_irq_pending
Malta:
- Rewrite to use DT
of/platform:
- Probe "isa" busses by default
CM:
- Print CM error reports upon bus errors
Module:
- Migrate exception table users off module.h and onto extable.h
- Make various drivers explicitly non-modular:
- Audit and remove any unnecessary uses of module.h
mailmap:
- Canonicalize to Qais' current email address.
Documentation:
- MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
Loongson1C:
- Add CPU support for Loongson1C
- Add board support
- Add defconfig
- Add RTC support for Loongson1C board
All this except one Documentation fix has sat in linux-next and has
survived Imagination's automated build test system"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
MIPS: ptrace: Fix regs_return_value for kernel context
MIPS: VDSO: Drop duplicated -I*/-E* aflags
MIPS: Fix -mabi=64 build of vdso.lds
MIPS: Enable hardened usercopy
MIPS: generic: Convert SEAD-3 to a generic board
MIPS: generic: Introduce generic DT-based board support
MIPS: Support generating Flattened Image Trees (.itb)
MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
MIPS: Print CM error reports upon bus errors
MIPS: Support per-device DMA coherence
MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
MIPS: Sanitise coherentio semantics
MIPS: PCI: Support generic drivers
MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
MIPS: PCI: Inline pcibios_assign_all_busses
MIPS: PCI: Make pcibios_set_cache_line_size an initcall
MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
MIPS: PCI: Use struct list_head lists
...
The timeout loop terminates when the loop count is zero, but the decrement
of the count variable is post check. So count is -1 when we check for the
timeout and therefor the error message is supressed.
Change it to predecrement, so the error message is emitted.
[ tglx: Massaged changelog ]
Fixes: a2c2251012 ("irqchip: gic-v3: Refactor gic_enable_redist to support both enabling and disabling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20161014072534.GA15168@mwanda
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The J-Core AIC does not have separate interrupt numbers reserved for
cpu-local vs global interrupts. Instead, the driver requesting the irq
is expected to know whether its device uses per-cpu interrupts or not.
Previously it was assumed that handle_simple_irq could work for both
cases, but it intentionally drops interrupts for an irq number that
already has a handler running. This resulted in the timer interrupt
for one cpu being lost when multiple cpus' timers were set for
approximately the same expiration time, leading to stalls. In theory
the same could also happen with IPIs.
To solve the problem, instead of registering handle_simple_irq as the
handler, register a wrapper function which checks whether the irq to
be handled was requested as per-cpu or not, and passes it to
handle_simple_irq or handle_percpu_irq accordingly.
Fixes: 981b58f66c ("irqchip/jcore-aic: Add J-Core AIC driver")
Signed-off-by: Rich Felker <dalias@libc.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-sh@vger.kernel.org
Link: http://lkml.kernel.org/r/f18cec30bc17e3f52e478dd9f6714bfab02f227f.1476390724.git.dalias@libc.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge more updates from Andrew Morton:
- a few block updates that fell in my lap
- lib/ updates
- checkpatch
- autofs
- ipc
- a ton of misc other things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (100 commits)
mm: split gfp_mask and mapping flags into separate fields
fs: use mapping_set_error instead of opencoded set_bit
treewide: remove redundant #include <linux/kconfig.h>
hung_task: allow hung_task_panic when hung_task_warnings is 0
kthread: add kerneldoc for kthread_create()
kthread: better support freezable kthread workers
kthread: allow to modify delayed kthread work
kthread: allow to cancel kthread work
kthread: initial support for delayed kthread work
kthread: detect when a kthread work is used by more workers
kthread: add kthread_destroy_worker()
kthread: add kthread_create_worker*()
kthread: allow to call __kthread_create_on_node() with va_list args
kthread/smpboot: do not park in kthread_create_on_cpu()
kthread: kthread worker API cleanup
kthread: rename probe_kthread_data() to kthread_probe_data()
scripts/tags.sh: enable code completion in VIM
mm: kmemleak: avoid using __va() on addresses that don't have a lowmem mapping
kdump, vmcoreinfo: report memory sections virtual addresses
ipc/sem.c: add cond_resched in exit_sme
...
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Including:
* Support for interrupt virtualization in the AMD IOMMU driver.
These patches were shared with the KVM tree and are already
merged through that tree.
* Generic DT-binding support for the ARM-SMMU driver. With this
the driver now makes use of the generic DMA-API code. This
also required some changes outside of the IOMMU code, but
these are acked by the respective maintainers.
* More cleanups and fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1hFE
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- support for interrupt virtualization in the AMD IOMMU driver. These
patches were shared with the KVM tree and are already merged through
that tree.
- generic DT-binding support for the ARM-SMMU driver. With this the
driver now makes use of the generic DMA-API code. This also required
some changes outside of the IOMMU code, but these are acked by the
respective maintainers.
- more cleanups and fixes all over the place.
* tag 'iommu-updates-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (40 commits)
iommu/amd: No need to wait iommu completion if no dte irq entry change
iommu/amd: Free domain id when free a domain of struct dma_ops_domain
iommu/amd: Use standard bitmap operation to set bitmap
iommu/amd: Clean up the cmpxchg64 invocation
iommu/io-pgtable-arm: Check for v7s-incapable systems
iommu/dma: Avoid PCI host bridge windows
iommu/dma: Add support for mapping MSIs
iommu/arm-smmu: Set domain geometry
iommu/arm-smmu: Wire up generic configuration support
Docs: dt: document ARM SMMU generic binding usage
iommu/arm-smmu: Convert to iommu_fwspec
iommu/arm-smmu: Intelligent SMR allocation
iommu/arm-smmu: Add a stream map entry iterator
iommu/arm-smmu: Streamline SMMU data lookups
iommu/arm-smmu: Refactor mmu-masters handling
iommu/arm-smmu: Keep track of S2CR state
iommu/arm-smmu: Consolidate stream map entry state
iommu/arm-smmu: Handle stream IDs more dynamically
iommu/arm-smmu: Set PRIVCFG in stage 1 STEs
iommu/arm-smmu: Support non-PCI devices with SMMUv3
...
Pull irq fixes from Thomas Gleixner:
"Two small kerneldoc fixes from Julia Lawall"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/metag-ext: Improve function-level documentation
irqchip/vic: Improve function-level documentation
The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion
of old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files.
If no regressions are found, another large cleanup for the platform
will happen as a follow-up, removing dead code and restructuring
the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now DT-only.
The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT
in principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress.
We can probably merge the remaining code into a single directory
in the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then.
Conflicts: two files deleted here have been modified upstream,
the changes can be discarded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WaLy
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion of
old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files. If no regressions are found, another
large cleanup for the platform will happen as a follow-up, removing
dead code and restructuring the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now
DT-only. The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT in
principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress. We
can probably merge the remaining code into a single directory in
the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: select PCI_DOMAINS config from ARCH_MULTIPLATFORM
ARM: stop *MIGHT_HAVE_PCI* config from being selected redundantly
ARM: imx: (trivial) fix typo and grammar
ARM: clps711x: remove extraneous files
ARM: imx: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP2+: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP1: use IS_ENABLED() instead of checking for built-in or module
ARM: imx: remove platform-mxc_rnga
ARM: realview: imply device tree boot
ARM: realview: no need to select SMP_ON_UP explicitly
ARM: realview: delete the RealView board files
ARM: imx: no need to select SMP_ON_UP explicitly
ARM: i.MX: Move SOC_IMX1 into 'Device tree only'
ARM: i.MX: Remove i.MX1 non-DT support
ARM: i.MX: Remove i.MX1 Synertronixx SCB9328 board support
ARM: i.MX: Remove i.MX1 Armadeus APF9328 board support
ARM: mxs: remove obsolete startup code for TX28
ARM: i.MX31 iomux: remove duplicates with alternate name
ARM: i.MX31 iomux: remove plain duplicates
ARM: OMAP2+: Drop legacy board file for LDP
...
The i8259A_irq_pending function is unused. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14271/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The default i8259 polling function (i8259_irq) is nicely generic but is
fairly costly. Platforms often provide an alternative means of polling
for an i8259 interrupt, and when using the i8259 without device tree
have typically just chained its parent interrupt to their own handler
function. In order to allow for platform-specific polling functions to
be used in cases where the driver is probed via device tree, provide an
i8259_set_poll function that accepts a pointer to an alternative poll
function that will override the default.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14270/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mapping the parent IRQ will use a virq number which may conflict with
the hardcoded I8259A_IRQ_BASE..I8259A_IRQ_BASE+15 range that the i8259
driver expects to be free. If this occurs then we'll hit errors when
adding the i8259 IRQ domain, since one of its virq numbers will already
be in use.
Avoid this by adding the i8259 domain before mapping the parent IRQ,
such that the i8259 virq numbers become used before the parent interrupt
controller gets a chance to use any of them.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14269/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The STM32 external interrupt controller consists of edge detectors that
generate interrupts requests or wake-up events.
Each line can be independently configured as interrupt or wake-up source,
and triggers either on rising, falling or both edges. Each line can also
be masked independently.
Originally-from: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: arnd@arndb.de
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: bruherrera@gmail.com
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: lee.jones@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1474387259-18926-3-git-send-email-alexandre.torgue@st.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The MIPS GIC driver has previously iterated over bits set in a bitmap
representing pending local IRQs by calling find_first_bit, clearing that
bit then calling find_first_bit again until all bits are clear. If
multiple interrupts are pending then this is wasteful, as find_first_bit
will have to loop over the whole bitmap from the start. Use the
for_each_set_bit macro which performs exactly what we need here instead.
It will use find_next_bit and thus only scan over the relevant part of
the bitmap, and it makes the intent of the code clearer.
This makes the same change for local interrupts that commit cae750bae4
("irqchip: mips-gic: Use for_each_set_bit to iterate over IRQs") made
for shared interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/20160913165427.31686-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the device hierarchy domain was added by commit c98c1822ee
("irqchip/mips-gic: Add device hierarchy domain"), GIC local interrupts
have been broken.
Users attempting to setup a per-cpu local IRQ, for example the GIC timer
clock events code in drivers/clocksource/mips-gic-timer.c, the
setup_percpu_irq function would refuse with -EINVAL because the GIC
irqchip driver never called irq_set_percpu_devid so the
IRQ_PER_CPU_DEVID flag was never set for the IRQ. This happens because
irq_set_percpu_devid was being called from the gic_irq_domain_map
function which is no longer called.
Doing only that runs into further problems because gic_dev_domain_alloc
set the struct irq_chip for all interrupts, local or shared, to
gic_level_irq_controller despite that only being suitable for shared
interrupts. The typical outcome of this is that gic_level_irq_controller
callback functions are called for local interrupts, and then hwirq
number calculations overflow & the driver ends up attempting to access
some invalid register with an address calculated from an invalid hwirq
number. Best case scenario is that this then leads to a bus error. This
is fixed by abstracting the setup of the hwirq & chip to a new function
gic_setup_dev_chip which is used by both the root GIC IRQ domain & the
device domain.
Finally, decoding local interrupts failed because gic_dev_domain_alloc
only called irq_domain_alloc_irqs_parent for shared interrupts. Local
ones were therefore never associated with hwirqs in the root GIC IRQ
domain and the virq in gic_handle_local_int would always be 0. This is
fixed by calling irq_domain_alloc_irqs_parent unconditionally & having
gic_irq_domain_alloc handle both local & shared interrupts, which is
easy due to the aforementioned abstraction of chip setup into
gic_setup_dev_chip.
This fixes use of the MIPS GIC timer for clock events, which has been
broken since c98c1822ee ("irqchip/mips-gic: Add device hierarchy
domain") but hadn't been noticed due to a silent fallback to the MIPS
coprocessor 0 count/compare clock events device.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: stable@vger.kernel.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20160913165335.31389-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gic_raise_softirq() walks the list of cpus using for_each_cpu(), it calls
gic_compute_target_list() which advances the iterator by the number of
CPUs in the cluster.
If gic_compute_target_list() reaches the last CPU it leaves the iterator
pointing at the last CPU. This means the next time round the for_each_cpu()
loop cpumask_next() will be called with an invalid CPU.
This triggers a warning when built with CONFIG_DEBUG_PER_CPU_MAPS:
[ 3.077738] GICv3: CPU1: found redistributor 1 region 0:0x000000002f120000
[ 3.077943] CPU1: Booted secondary processor [410fd0f0]
[ 3.078542] ------------[ cut here ]------------
[ 3.078746] WARNING: CPU: 1 PID: 0 at ../include/linux/cpumask.h:121 gic_raise_softirq+0x12c/0x170
[ 3.078812] Modules linked in:
[ 3.078869]
[ 3.078930] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.8.0-rc5+ #5188
[ 3.078994] Hardware name: Foundation-v8A (DT)
[ 3.079059] task: ffff80087a1a0080 task.stack: ffff80087a19c000
[ 3.079145] PC is at gic_raise_softirq+0x12c/0x170
[ 3.079226] LR is at gic_raise_softirq+0xa4/0x170
[ 3.079296] pc : [<ffff0000083ead24>] lr : [<ffff0000083eac9c>] pstate: 200001c9
[ 3.081139] Call trace:
[ 3.081202] Exception stack(0xffff80087a19fbe0 to 0xffff80087a19fd10)
[ 3.082269] [<ffff0000083ead24>] gic_raise_softirq+0x12c/0x170
[ 3.082354] [<ffff00000808e614>] smp_send_reschedule+0x34/0x40
[ 3.082433] [<ffff0000080e80a0>] resched_curr+0x50/0x88
[ 3.082512] [<ffff0000080e89d0>] check_preempt_curr+0x60/0xd0
[ 3.082593] [<ffff0000080e8a60>] ttwu_do_wakeup+0x20/0xe8
[ 3.082672] [<ffff0000080e8bb8>] ttwu_do_activate+0x90/0xc0
[ 3.082753] [<ffff0000080ea9a4>] try_to_wake_up+0x224/0x370
[ 3.082836] [<ffff0000080eabc8>] default_wake_function+0x10/0x18
[ 3.082920] [<ffff000008103134>] __wake_up_common+0x5c/0xa0
[ 3.083003] [<ffff0000081031f4>] __wake_up_locked+0x14/0x20
[ 3.083086] [<ffff000008103f80>] complete+0x40/0x60
[ 3.083168] [<ffff00000808df7c>] secondary_start_kernel+0x15c/0x1d0
[ 3.083240] [<00000000808911a4>] 0x808911a4
[ 3.113401] Detected PIPT I-cache on CPU2
Avoid updating the iterator if the next call to cpumask_next() would
cause the for_each_cpu() loop to exit.
There is no change to gic_raise_softirq()'s behaviour, (cpumask_next()s
eventual call to _find_next_bit() will return early as start >= nbits),
this patch just silences the warning.
Fixes: 021f653791 ("irqchip: gic-v3: Initial support for GICv3")
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1474306155-3303-1-git-send-email-james.morse@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When an MSI doorbell is located downstream of an IOMMU, attaching
devices to a DMA ops domain and switching on translation leads to a rude
shock when their attempt to write to the physical address returned by
the irqchip driver faults (or worse, writes into some already-mapped
buffer) and no interrupt is forthcoming.
Address this by adding a hook for relevant irqchip drivers to call from
their compose_msi_msg() callback, to swizzle the physical address with
an appropriatly-mapped IOVA for any device attached to one of our DMA
ops domains.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
aic5_irq_domain_xlate() and aic_irq_domain_xlate() take the generic chip
lock without disabling interrupts, which can lead to a deadlock if an
interrupt occurs while the lock is held in one of these functions.
Replace irq_gc_{lock,unlock}() calls by
irq_gc_{lock_irqsave,unlock_irqrestore}() ones to prevent this bug from
happening.
Fixes: b1479ebb77 ("irqchip: atmel-aic: Add atmel AIC/AIC5 drivers")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable@vger.kernel.org
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Link: http://lkml.kernel.org/r/1473775109-4192-2-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Let ACPI build ITS PCI MSI domain. ACPI code is responsible for retrieving
inner domain token and passing it on to its_pci_msi_init_one generic
init call.
IORT maintains list of registered domain tokens and allows to find
corresponding domain based on MADT ITS subtable ID info.
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Firmware agnostic code lands in common functions which do necessary
domain initialization based on unique domain handler. DT specific
code goes to DT specific init call.
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
ITS is prepared for being initialized different than DT,
therefore we can initialize it in ACPI way. We collect register base
address from MADT table and pass mandatory info to firmware-agnostic
ITS init call.
Use here IORT lib to register ITS domain which then can be found and
used on to build another PCI MSI domain in hierarchical stack domain.
NOTE: Waiting for proper ITS and NUMA node relation description in IORT
table, we pass around NUMA_NO_NODE to the its_probe_one init call.
This means that Cavium ThunderX erratum 23144 (pass1.1 only)
is not supported for ACPI boot method yet.
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to add ACPI support we need to isolate ACPI&DT common code and
move DT logic to corresponding functions. To achieve this we are using
firmware agnostic handle which can be unpacked to either DT or ACPI node.
No functional changes other than a very minor one:
1. Terminate its_init call with -ENODEV for non-DT case which allows
to remove hack from its-gic-v3.c.
2. Fix ITS base register address type (from 'unsigned long' to 'phys_addr_t'),
as a bonus we get nice string formatting.
3. Since there is only one of ITS parent domain convert it to static global
variable and drop the parameter from its_probe_one. Users can refer to it
in more convenient way then.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no point to initialize ITS without having msi-controller
property in corresponding DT node. However, its_probe is checking
msi-controller presence at the end, so we can save our time and do that
check prior to its_probe call. Also, for the code clarity purpose,
we put domain initialization to separate function.
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We get 1 warning when building kernel with W=1:
drivers/irqchip/irq-gic.c:917:13: warning: no previous prototype for 'gic_init_physaddr' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit 498b5fdd40 ("PM / clk: Add support for adding a specific clock
from device-tree") add a new helper function for adding a clock from
device-tree to a device. Update the GIC-PM driver to use this new
function to simplify the driver.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently, when running on FVP, CPU 0 boots up with its BPR changed from
the reset value. This renders it impossible to (preemptively) prioritize
interrupts on CPU 0.
This is harmless on normal systems since Linux typically does not
support preemptive interrupts. It does however cause problems in
systems with additional changes (such as patches for NMI simulation).
Many thanks to Andrew Thoelke for suggesting the BPR as having the
potential to harm preemption.
Suggested-by: Andrew Thoelke <andrew.thoelke@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The BL switcher code manipulates the logical/physical CPU mapping,
forcing a lock to be taken on the IPI path. With an IPI heavy load,
this single lock becomes contended.
But when CONFIG_BL_SWITCHER is not enabled, there is no reason
to take this lock at all since the CPU mapping is immutable.
This patch allows the lock to be entierely removed when BL_SWITCHER
is not enabled (which is the case in most configurations), leading
to a small improvement of "perf bench sched pipe" (measured on
an 8 core AMD Seattle system):
Before: 101370 ops/sec
After: 103680 ops/sec
Take this opportunity to remove a useless lock being taken when
handling an interrupt on a secondary GIC.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
around the Kconfig options and leaves the mach-realview
directory nice and tidy, with all boards migrated over to
Device Tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HWSr
-----END PGP SIGNATURE-----
Merge tag 'realview-broomstick-sweep' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/cleanup
Merge "delete the RealView boardfiles" from Linus Walleij:
This deletes the realview boardfiles, consolidates a bit
around the Kconfig options and leaves the mach-realview
directory nice and tidy, with all boards migrated over to
Device Tree.
* tag 'realview-broomstick-sweep' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: imply device tree boot
ARM: realview: no need to select SMP_ON_UP explicitly
ARM: realview: delete the RealView board files
The MIPS GIC driver has previously iterated over bits set in a bitmap
representing pending IRQs by calling find_first_bit, clearing that bit
then calling find_first_bit again until all bits are clear. If multiple
interrupts are pending then this is wasteful, as find_first_bit will
have to loop over the whole bitmap from the start. Use the
for_each_set_bit macro which performs exactly what we need here instead.
It will use find_next_bit and thus only scan over the relevant part of
the bitmap, and it makes the intent of the code more clear.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Link: https://lkml.kernel.org/r/20160819171119.28121-1-paul.burton@imgtec.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Fixes the following sparse warning:
drivers/irqchip/irq-jcore-aic.c:47:12: warning:
symbol 'aic_irq_of_init' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Link: https://lkml.kernel.org/r/1471706788-27587-1-git-send-email-weiyj.lk@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell Armada 7K/8K integrates a secondary interrupt controller
very originally named "PIC". It is connected to the main GIC via a
PPI. Amongst other things, this PIC is used for the ARM PMU.
This commit adds a simple irqchip driver for this interrupt
controller. Since this interrupt controller is not needed early at boot
time, we make the driver a proper platform driver rather than use the
IRQCHIP_DECLARE() mechanism.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1470408921-447-3-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
If an IRQ is setup using __setup_irq(), which is used by the
request_irq() family of functions, and we are using an SMP kernel then
the affinity of the IRQ will be set via setup_affinity() immediately
after the IRQ is enabled. This call to gic_set_affinity() will lead to
the interrupt being mapped to a VPE. However there are other ways to use
IRQs which don't cause affinity to be set, for example if it is used to
chain to another IRQ controller with irq_set_chained_handler_and_data().
The irq_set_chained_handler_and_data() code path will enable the IRQ,
but will not trigger a call to gic_set_affinity() and in this case
nothing will map the interrupt to a VPE, meaning that the interrupt is
never received.
Fix this by implementing the activate operation for the GIC device IRQ
domain, using gic_shared_irq_domain_map() to map the interrupt to the
correct pin of cpu 0.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160819170715.27820-2-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gic_shared_irq_domain_map() is called from gic_irq_domain_alloc() where
the wrong chip has been set, and is then overwritten. Tidy this up by
setting the correct chip the first time, and setting the
handle_level_irq handler from gic_irq_domain_alloc() too.
gic_shared_irq_domain_map() is also called from gic_irq_domain_map(),
which now calls irq_set_chip_and_handler() to retain its previous
behaviour.
This patch prepares for a follow-on which will call
gic_shared_irq_domain_map() from a callback where the lock on the struct
irq_desc is held, which without this change would cause the call to
irq_set_chip_and_handler() to lead to a deadlock.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160819170715.27820-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When starting a kexec/kdump kernel, the GIC ITS will already have been
enabled. According to the ARM Generic Interrupt Controller
Architecture Specification (GIC architecture Version 3.0 and version
4.0), writing to GITS_BASER<n> or GITS_CBASER is "UNPREDICTABLE" when
the ITS is enabled. On Cavium Thunder systems, this prevents the ITS
from being initializing in the kexec/kdump kernel, resulting in
failure to register/enable interrupts for all devices.
The fix is to disable the ITS if it is not already in the disabled
state. This allows the ITS to be properly initialized and then
re-enabled in the kexec/kdump kernel.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As per the GICv3 specification, to power down a processor using GICv3
and allow automatic power-on if an interrupt must be sent to a processor,
software must set Enable to zero for all interrupt groups(by writing
to GICC_CTLR or ICC_IGRPEN{0,1}_EL1/3 as appropriate.
When commit 3708d52fc6 ("irqchip: gic-v3: Implement CPU PM notifier")
was introduced there were no firmware implementations(in particular PSCI)
handling this.
Linux kernel may not be aware of the CPU power state details and might
fail to identify the power states that require quiescing the CPU
interface. Even if it can be aware of those details, it can't determine
which CPU power state have been triggered at the platform level and how
the power control is implemented.
This patch make disabling redistributor and group1 non-secure interrupts
in the power down path and re-enabling of redistributor in the power-up
path conditional. It will be handled in the kernel if and only if the
non-secure accesses are permitted to access and modify control registers.
It is left to the platform implementation otherwise.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On systems where a single CPU is present, the GIC may not support
having SGIs delivered to a target list. In that case, we use the
self-SGI mechanism to allow the interrupt to be delivered locally.
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This reduces the Kconfig for the RealView by assuming we are
always booting from the device tree, and removing all the uses
of CONFIG_REALVIEW_DT and replacing with CONFIG_ARCH_REALVIEW.
Further:
- Drop REALVIEW_HIGH_PHYS_OFFSET: we don't use this with device
tree.
- Drop the REALVIEW_EB_ARM11MP_REVB option: we now handle this
by simply using another device tree.
- Drop the PB1176 secure flash option: this is defined in the
PB1176 device tree but marked as "disabled", so users who
want to use it can simply enable it in the device tree and
go hacking around.
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are two versions of the J-Core interrupt controller in use, aic1
which generates interrupts with programmable priorities, but only
supports 8 irq lines and maps them to cpu traps in the range 17 to 24,
and aic2 which uses traps in the range 64-127 and supports up to 128
irqs, with priorities dependent on the interrupt number. The Linux
driver does not make use of priorities anyway.
For simplicity, there is no aic1-specific logic in the driver beyond
setting the priority register, which is necessary for interrupts to
work at all. Eventually aic1 will likely be phased out, but it's
currently in use in deployments and all released bitstream binaries.
Signed-off-by: Rich Felker <dalias@libc.org>
Link: https://lkml.kernel.org/r/c3b89ef74aaa6477575dbe2d410eb1d182503243.147018b6529.git.dalias@libc.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
Pull irq updates from Thomas Gleixner:
"The irq department delivers:
- new core infrastructure to allow better management of multi-queue
devices (interrupt spreading, node aware descriptor allocation ...)
- a new interrupt flow handler to support the new fangled Intel VMD
devices.
- yet another new interrupt controller driver.
- a series of fixes which addresses sparse warnings, missing
includes, missing static declarations etc from Ben Dooks.
- a fix for the error handling in the hierarchical domain allocation
code.
- the usual pile of small updates to core and driver code"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
genirq: Fix missing irq allocation affinity hint
irqdomain: Fix irq_domain_alloc_irqs_recursive() error handling
irq/Documentation: Correct result of echnoing 5 to smp_affinity
MAINTAINERS: Remove Jiang Liu from irq domains
genirq/msi: Fix broken debug output
genirq: Add a helper to spread an affinity mask for MSI/MSI-X vectors
genirq/msi: Make use of affinity aware allocations
genirq: Use affinity hint in irqdesc allocation
genirq: Add affinity hint to irq allocation
genirq: Introduce IRQD_AFFINITY_MANAGED flag
genirq/msi: Remove unused MSI_FLAG_IDENTITY_MAP
irqchip/s3c24xx: Fixup IO accessors for big endian
irqchip/exynos-combiner: Fix usage of __raw IO
irqdomain: Fix disposal of mappings for interrupt hierarchies
irqchip/aspeed-vic: Add irq controller for Aspeed
doc/devicetree: Add Aspeed VIC bindings
x86/PCI/VMD: Use untracked irq handler
genirq: Add untracked irq handler
irqchip/mips-gic: Populate irq_domain names
irqchip/gicv3-its: Implement two-level(indirect) device table support
...
When building with CONFIG_SMP disabled, we get some new harmless warnings:
drivers/irqchip/irq-armada-370-xp.c:356:12: error: 'mpic_cascaded_starting_cpu' defined but not used [-Werror=unused-function]
static int mpic_cascaded_starting_cpu(unsigned int cpu)
^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/irqchip/irq-armada-370-xp.c:349:12: error: 'armada_xp_mpic_starting_cpu' defined but not used [-Werror=unused-function]
static int armada_xp_mpic_starting_cpu(unsigned int cpu)
This moves the unused functions into the #ifdef, as they previously were.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Cochran <rcochran@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: cb5ff2d245 ("irqchip/armada-370-xp: Convert to hotplug state machine")
Link: http://lkml.kernel.org/r/20160718160335.3134412-1-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153333.416260485@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153333.330661455@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153333.244546182@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153333.163186301@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
More or less straightforward, although this driver sports some very
interesting SMP setup code. Regarding the callback ordering, this
deleted comment is interesting:
... the GIC needs to be up before the ARM generic timers.
That comment is half baken as the same requirement is true for perf.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153333.069777215@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch changes the compatibility string to match with the smallest
supported chip (EP7209). Since the DT-support for this CPU is not yet
announced, this change is safe.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When mapping an interrupt to a VP(E) we must use the identifier for the
VP that the hardware expects, and this does not always match up with the
Linux CPU number. Commit d46812bb0b ("irqchip: mips-gic: Use HW IDs
for VPE_OTHER_ADDR") corrected this for the cases that existed at the
time it was written, but commit 2af70a9620 ("irqchip/mips-gic: Add a
IPI hierarchy domain") added another case before the former patch was
merged. This leads to incorrectly using Linux CPU numbers when mapping
interrupts to VPs, which breaks on certain systems such as those with
multi-core I6400 CPUs. Fix by adding the appropriate call to
mips_cm_vp_id() to retrieve the expected VP identifier.
Fixes: d46812bb0b ("irqchip: mips-gic: Use HW IDs for VPE_OTHER_ADDR")
Fixes: 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160705132600.27730-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Instead of using the __raw accessors, use the _relaxed versions
to deal with any issues due to endian-ness of the CPU.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[jac: reformat subject line, fix commit message typo]
Link: https://lkml.kernel.org/r/1466504432-24187-10-git-send-email-ben.dooks@codethink.co.uk
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Fix the use of __raw IO accessors when the readl/writel_relaxed
are better. This should fix issues if the kernel is running as
big endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[jac: reformat subject line, fix commit message typo]
Link: https://lkml.kernel.org/r/1466504432-24187-9-git-send-email-ben.dooks@codethink.co.uk
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The PCI_MSI symbol is used inconsistently throughout the tree, with some
drivers using 'select' and others using 'depends on', or using conditional
selects. This keeps causing problems; the latest one is a result of
ARCH_ALPINE using a 'select' statement to enable its platform-specific MSI
driver without enabling MSI:
warning: (ARCH_ALPINE) selects ALPINE_MSI which has unmet direct dependencies (PCI && PCI_MSI)
drivers/irqchip/irq-alpine-msi.c:104:15: error: variable 'alpine_msix_domain_info' has initializer but incomplete type
static struct msi_domain_info alpine_msix_domain_info = {
^~~~~~~~~~~~~~~
drivers/irqchip/irq-alpine-msi.c:105:2: error: unknown field 'flags' specified in initializer
.flags = MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS |
^
drivers/irqchip/irq-alpine-msi.c:105:11: error: 'MSI_FLAG_USE_DEF_DOM_OPS' undeclared here (not in a function)
.flags = MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS |
^~~~~~~~~~~~~~~~~~~~~~~~
There is little reason to enable PCI support for a platform that uses MSI
but then leave MSI disabled at compile time.
Select PCI_MSI from irqchips that implement MSI, and make PCI host bridges
that use MSI on ARM depend on PCI_MSI_IRQ_DOMAIN.
For all three architectures that support PCI_MSI_IRQ_DOMAIN (ARM, ARM64,
X86), enable it by default whenever MSI is enabled.
[bhelgaas: changelog, omit crypto config change]
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
When allocating a new device IRQ, gic_dev_domain_alloc() correctly calls
irq_domain_set_hwirq_and_chip(), but gic_irq_domain_alloc() does not. This
means that gic_irq_domain believes all IRQs from the dev domain have an
hwirq of 0 and creates incorrect mappings in the linear_revmap. As
gic_irq_domain is a parent of the gic_dev_domain, this leads to an
inability to boot on devices with a GIC. Excerpt of the error:
[ 2.297649] irq 0: nobody cared (try booting with the "irqpoll" option)
...
[ 2.436963] handlers:
[ 2.439492] Disabling IRQ #0
Fix this by calling irq_domain_set_hwirq_and_chip() for both the dev and
irq domain.
Now that we are modifying the parent domain, be sure to clear it up in
case of an allocation error.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Fixes: 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy domain")
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Tested-by: Govindraj Raja <Govindraj.Raja@imgtec.com> # On Pistachio SoC
Reviewed-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1464001552-31174-1-git-send-email-harvey.hunt@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since device IDs are extremely sparse, the single, a.k.a flat table is
not sufficient for the following two reasons.
1) According to ARM-GIC spec, ITS hw can access maximum of 256(pages)*
64K(pageszie) bytes. In the best case, it supports upto DEVid=21
sparse with minimum device table entry size 8bytes.
2) The maximum memory size that is possible without memblock depends on
MAX_ORDER. 4MB on 4K page size kernel with default MAX_ORDER, so it
supports DEVid range 19bits.
The two-level device table feature brings us two advantages, the first
is a very high possibility of supporting upto 32bit sparse, and the
second one is the best utilization of memory allocation.
The feature is enabled automatically during driver probe if the memory
requirement is more than 2*ITS-pages and the hardware is capable of
two-level table walk.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
No references to argument 'node_name' after modifying pr_xxx()
messages to include ITS base address instead of 'node_name'.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The function is getting out of control, it has too many goto
statements and would be too complicated for adding a feature
two-level device table. So, it is time for us to cleanup and
move some of the logic to a separate function without affecting
the existing functionality.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Only the device table BASERn needs to be handled differently as
compared to all other tables. So, adding a separate function for
easy code maintenance and improved code readability.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds the two handy helper functions for reading and writing
ITS BASERn register.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
[Marc: Folded its_write_baser_cache into its_write_baser]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a platform driver to support non-root GICs that require runtime
power-management. Currently, only non-root GICs are supported because
the functions, smp_cross_call() and set_handle_irq(), that need to
be called for a root controller are located in the __init section and
so cannot be called by the platform driver.
The GIC platform driver re-uses many functions from the existing GIC
driver including some functions to save and restore the GIC context
during power transitions. The functions for saving and restoring the
GIC context are currently only defined if CONFIG_CPU_PM is enabled and
to ensure that these functions are always defined when the platform
driver is enabled, a dependency on CONFIG_ARM_GIC_PM (which selects the
platform driver) has been added.
In order to re-use the private GIC initialisation code, a new public
function, gic_of_init_child(), has been added which calls various
private functions to initialise the GIC. This is different from the
existing gic_of_init() because it only supports non-root GICs (ie. does
not call smp_cross_call() is set_handle_irq()) and is not located in
the __init section (so can be used by platform drivers). Furthermore,
gic_of_init_child() dynamically allocates memory for the GIC chip data
which is also different from gic_of_init().
There is no specific suspend handling for GICs registered as platform
devices. Non-wakeup interrupts will be disabled by the kernel during
late suspend, however, this alone will not power down the GIC if
interrupts have been requested and not freed. Therefore, requestors of
non-wakeup interrupts will need to free them on entering suspend in
order to power-down the GIC.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
To support GICs that require runtime power management, it is necessary
to add a platform driver, so that the probing of the chip can be
deferred if resources, such as a power-domain, is not yet available.
To prepare for adding a platform driver:
1. Drop the __init section from the gic_dist_config() so this can be
re-used by the platform driver.
2. Add prototypes for functions required by the platform driver to the
GIC header file so they can be re-used.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
For GICs that require runtime power-management it is necessary to
populate the 'parent_device' member of the irqchip structure. In
preparation for supporting such GICs, move the code that initialises
the irqchip structure for a GIC into its own function called
gic_init_chip() where the parent device pointer is also set.
Instead of calling gic_init_chip() from within gic_init_bases(), move
the calls to outside of this function, so that in the future we can
avoid having to pass additional parameters to gic_init_bases() in order
set the parent device pointer or set the name to a specific string.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
To re-use the code that initialises the GIC (found in
__gic_init_bases()), from within a platform driver, it is necessary to
move the code from the __init section so that it is always present and
not removed. Unfortunately, it is not possible to simply drop the __init
from the function declaration for __gic_init_bases() because it contains
calls to set_smp_cross_call() and set_handle_irq() which are both
located in the __init section. Fortunately, these calls are only
required for the root controller and because the initial platform driver
will only support non-root controllers that can be initialised later in
the boot process, we can move these calls to another function.
Move the bulk of the code from __gic_init_bases() to a new function
called gic_init_bases() which is not located in the __init section and
can be used by the platform driver. Update __gic_init_bases() to call
gic_init_bases() and if necessary, set_smp_cross_call() and
set_handle_irq().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The vic_syscore_ops and vic_of_init functions are not exported
outside the driver, so make them static to remove the following
warnings:
drivers/irqchip/irq-vic.c:170:20: warning: symbol 'vic_syscore_ops' was not declared. Should it be static?
drivers/irqchip/irq-vic.c:520:12: warning: symbol 'vic_of_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lkml.kernel.org/r/1465468212-2937-1-git-send-email-ben.dooks@codethink.co.uk
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Fix the missing include of <linux/irqchip/irq-omap-intc.h> which
declares all the missing functions from the following warnings:
drivers/irqchip/irq-omap-intc.c:84:6: warning: symbol 'omap_intc_save_context' was not declared. Should it be static?
drivers/irqchip/irq-omap-intc.c:105:6: warning: symbol 'omap_intc_restore_context' was not declared. Should it be static?
drivers/irqchip/irq-omap-intc.c:124:6: warning: symbol 'omap3_intc_prepare_idle' was not declared. Should it be static?
drivers/irqchip/irq-omap-intc.c:134:6: warning: symbol 'omap3_intc_resume_idle' was not declared. Should it be static?
drivers/irqchip/irq-omap-intc.c:173:5: warning: symbol 'omap_irq_pending' was not declared. Should it be static?
drivers/irqchip/irq-omap-intc.c:183:6: warning: symbol 'omap3_intc_suspend' was not declared. Should it be static?
drivers/irqchip/irq-omap-intc.c:365:13: warning: symbol 'omap3_init_irq' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lkml.kernel.org/r/1465407872-10299-1-git-send-email-ben.dooks@codethink.co.uk
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Fix the missing declaration of gicv2m_init() by including the
file <linux/irqchip/arm-gic.h> which defines it. Fixes the
warning:
drivers/irqchip/irq-gic-v2m.c:517:12: warning: symbol 'gicv2m_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lkml.kernel.org/r/1465408414-13698-1-git-send-email-ben.dooks@codethink.co.uk
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The probe functions in this driver is not exported or declared
so make it static to fix the following warning:
drivers/irqchip/irq-brcmstb-l2.c:115:12: warning: symbol 'brcmstb_l2_intc_of_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lkml.kernel.org/r/1465408940-16414-1-git-send-email-ben.dooks@codethink.co.uk
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The probe functions in this driver are not exported or declared
for use elsewhere, so make them static to fix the warnings:
drivers/irqchip/irq-bcm7120-l2.c:218:12: warning: symbol 'bcm7120_l2_intc_probe' was not declared. Should it be static?
drivers/irqchip/irq-bcm7120-l2.c:342:12: warning: symbol 'bcm7120_l2_intc_probe_7120' was not declared. Should it be static?
drivers/irqchip/irq-bcm7120-l2.c:349:12: warning: symbol 'bcm7120_l2_intc_probe_3380' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lkml.kernel.org/r/1465408798-16201-1-git-send-email-ben.dooks@codethink.co.uk
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The bcm2836_smp_boot_secondary() is not declared or used elsewhere
so make it static to fix the following warning:
drivers/irqchip/irq-bcm2836.c:227:12: warning: symbol 'bcm2836_smp_boot_secondary' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lkml.kernel.org/r/1465407697-8116-1-git-send-email-ben.dooks@codethink.co.uk
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The armada_370_xp_mpic_syscore_ops structure is not exported or
declared anywhere. Fix the following warning by making it static:
drivers/irqchip/irq-armada-370-xp.c:544:20: warning: symbol 'armada_370_xp_mpic_syscore_ops' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lkml.kernel.org/r/1465408533-13906-1-git-send-email-ben.dooks@codethink.co.uk
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With commit
76ba59f836 genirq: Add irq_domain-aware core IRQ handler
architecture-specific irq handlers are no longer necessary. Update the bcm2835
irq driver to use the core irq handler. As a bonus, this allows the driver to
support arm64 as well.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Link: https://lkml.kernel.org/r/1464728727-16300-1-git-send-email-eric@anholt.net
[jac reworded commit message for clarity]
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The wrong external interrupt bits are being set, offset by 1.
Signed-off-by: Joshua Henderson <digitalpeer@digitalpeer.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The erratum fixes the hang of ITS SYNC command by avoiding inter node
io and collections/cpu mapping on thunderx dual-socket platform.
This fix is only applicable for Cavium's ThunderX dual-socket platform.
Reviewed-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Ganapatrao Kulkarni <gkulkarni@caviumnetworks.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make sure the two sides of the bitwise operation are bool.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When EIC mode is in use (cpu_has_veic is true) enable it on each CPU
during GIC initialisation. Otherwise there may be a mismatch between the
hardware default interrupt model & that expected by the kernel.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Matt Redfearn <matt.redfearn@imgtec.com>
Tested-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13274/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The newly added nps irqchip driver causes build warnings on ARM64.
include/soc/nps/common.h: In function 'nps_host_reg_non_cl':
include/soc/nps/common.h:148:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
As the driver is only used on ARC, we don't need to see it without
COMPILE_TEST elsewhere, and we can avoid the warnings by only building
on 32-bit architectures even with CONFIG_COMPILE_TEST.
Acked-by: Marc Zyngier <narc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- x86: miscellaneous fixes, AVIC support (local APIC virtualization,
AMD version)
- s390: polling for interrupts after a VCPU goes to halted state is
now enabled for s390; use hardware provided information about facility
bits that do not need any hypervisor activity, and other fixes for
cpu models and facilities; improve perf output; floating interrupt
controller improvements.
- MIPS: miscellaneous fixes
- PPC: bugfixes only
- ARM: 16K page size support, generic firmware probing layer for
timer and GIC
Christoffer Dall (KVM-ARM maintainer) says:
"There are a few changes in this pull request touching things outside
KVM, but they should all carry the necessary acks and it made the
merge process much easier to do it this way."
though actually the irqchip maintainers' acks didn't make it into the
patches. Marc Zyngier, who is both irqchip and KVM-ARM maintainer,
later acked at http://mid.gmane.org/573351D1.4060303@arm.com
"more formally and for documentation purposes".
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXPJjyAAoJEL/70l94x66DhioH/j4fwQ0FmfPSM9PArzaFHQdx
LNE3tU4+bobbsy1BJr4DiAaOUQn3DAgwUvGLWXdeLiOXtoWXBiFHKaxlqEsCA6iQ
xcTH1TgfxsVoqGQ6bT9X/2GCx70heYpcWG3f+zqBy7ZfFmQykLAC/HwOr52VQL8f
hUFi3YmTHcnorp0n5Xg+9r3+RBS4D/kTbtdn6+KCLnPJ0RcgNkI3/NcafTemoofw
Tkv8+YYFNvKV13qlIfVqxMa0GwWI3pP6YaNKhaS5XO8Pu16HuuF1JthJsUBDzwBa
RInp8R9MoXgsBYhLpz3jc9vWG7G9yDl5LehsD9KOUGOaFYJ7sQN+QZOusa6jFgA=
=llO5
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small release overall.
x86:
- miscellaneous fixes
- AVIC support (local APIC virtualization, AMD version)
s390:
- polling for interrupts after a VCPU goes to halted state is now
enabled for s390
- use hardware provided information about facility bits that do not
need any hypervisor activity, and other fixes for cpu models and
facilities
- improve perf output
- floating interrupt controller improvements.
MIPS:
- miscellaneous fixes
PPC:
- bugfixes only
ARM:
- 16K page size support
- generic firmware probing layer for timer and GIC
Christoffer Dall (KVM-ARM maintainer) says:
"There are a few changes in this pull request touching things
outside KVM, but they should all carry the necessary acks and it
made the merge process much easier to do it this way."
though actually the irqchip maintainers' acks didn't make it into the
patches. Marc Zyngier, who is both irqchip and KVM-ARM maintainer,
later acked at http://mid.gmane.org/573351D1.4060303@arm.com ('more
formally and for documentation purposes')"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (82 commits)
KVM: MTRR: remove MSR 0x2f8
KVM: x86: make hwapic_isr_update and hwapic_irr_update look the same
svm: Manage vcpu load/unload when enable AVIC
svm: Do not intercept CR8 when enable AVIC
svm: Do not expose x2APIC when enable AVIC
KVM: x86: Introducing kvm_x86_ops.apicv_post_state_restore
svm: Add VMEXIT handlers for AVIC
svm: Add interrupt injection via AVIC
KVM: x86: Detect and Initialize AVIC support
svm: Introduce new AVIC VMCB registers
KVM: split kvm_vcpu_wake_up from kvm_vcpu_kick
KVM: x86: Introducing kvm_x86_ops VCPU blocking/unblocking hooks
KVM: x86: Introducing kvm_x86_ops VM init/destroy hooks
KVM: x86: Rename kvm_apic_get_reg to kvm_lapic_get_reg
KVM: x86: Misc LAPIC changes to expose helper functions
KVM: shrink halt polling even more for invalid wakeups
KVM: s390: set halt polling to 80 microseconds
KVM: halt_polling: provide a way to qualify wakeups during poll
KVM: PPC: Book3S HV: Re-enable XICS fast path for irqfd-generated interrupts
kvm: Conditionally register IRQ bypass consumer
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
- Support for EZChip (now Mellanox) NPS-400 Network processor based on ARC700
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy domains)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pnAx
-----END PGP SIGNATURE-----
Merge tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"We have a relatively big changeset for ARC for 4.7.
The highlight is support for EZChip (now Mellanox) NPS-400 network
processor, a 400-Gb throughput C-programmable packet processor based
on ARC700 cores from Synopsys. See
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
Also present are irqchip and clocksource drivers for NPS as agreed
with respective maintainers to go via ARC tree due to an soc header
dependency. I have the needed ACKs from Jason, Marc, Daniel. You
might run into a trivial merge conflict in drivers/irqchip/*
This EZChip platform support required some deep changes in ARC
architecture code and also opportunity to cleanup past sins (legacy
irq domains, missing irq domain lookup, hard coded timer irqs...)
Summary:
- Support for EZChip (now Mellanox) NPS-400 Network processor based
on ARC700
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy
domains)"
* tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (37 commits)
arc: axs103_smp: Fix CPU frequency to 100MHz for dual-core
arc: axs10x: Add DT bindings for I2S PLL Clock
ARC: pae: STRICT_MM_TYPECHECKS was broken
ARC: Add eznps platform to Kconfig and Makefile
ARC: [plat-eznps] Use dedicated COMMAND_LINE_SIZE
ARC: [plat-eznps] Use dedicated cpu_relax()
ARC: [plat-eznps] Use dedicated identity auxiliary register.
ARC: [plat-eznps] Use dedicated SMP barriers
ARC: [plat-eznps] Use dedicated atomic/bitops/cmpxchg
ARC: [plat-eznps] Use dedicated user stack top
ARC: [plat-eznps] Add eznps platform
ARC: [plat-eznps] Add eznps board defconfig and dts
ARC: Mark secondary cpu online only after all HW setup is done
ARC: rwlock: disable interrupts in !LLSC variant
ARC: Make vmalloc size configurable
ARC: clean out UAPI byteorder.h clean off Kconfig symbol
irqchip: add nps Internal and external irqchips
clocksource: Add NPS400 timers driver
soc: Support for EZchip SoC
Documentation: Add EZchip vendor to binding list
...
We get support for three new 32-bit SoC platforms this time. The amount
of changes in arch/arm for any of them is miniscule, as all the
interesting code is in device driver subsystems (irqchip, clk, pinctrl,
...) these days. I'm listing them here, as the addition of the Kconfig
statement is the main relevant milestone for a new platform. In each
case, some drivers are are shared with existing platforms, while
other drivers are added for v4.7 as well, or come in a later release.
- The Aspeed platform is probably the most interesting one, this is
what most whitebox servers use as their baseboard management
controller. We get support for the very common ast2400 and ast2500
SoCs. The OpenBMC project focuses on this chip, and the LWN
article about their ELC 2016 presentation at
https://lwn.net/Articles/683320/ triggered the submission, but the
code comes from IBM's OpenPOWER team rather than the team at
Facebook. There are still a lot more drivers that need to get added
over time, and I hope both teams can work together on that.
- OXNAS is an old platform for Network Attached Storage devices
from Oxford Semiconductor. There are models with ARM10 (!) and
ARM11MPCore cores, but for now, we only support the original ARM9
based versions.
The product lineup was subsequently part of PLX, Avago and now the
new Broadcom Ltd. https://wiki.openwrt.org/doc/hardware/soc/soc.oxnas
has some more information.
- V2M-MPS2 is a prototyping platform from ARM for their Cortex-M
cores and is related to the existing Realview / Versatile Express
lineup, but without MMU. We now support various NOMMU platforms,
so adding a new one is fairly straightforward.
http://infocenter.arm.com/help/topic/com.arm.doc.100112_0100_03_en/
has detailed information about the platform.
Other noteworthy updates:
- Work on LPC32xx has resumed, and Vladimir Zapolskiy and Sylvain Lemieux
are now maintaining the platform. This is an older ARM9 based
platform from NXP (not Freescale), but it remains in use in embedded
markets.
- Kevin Hilman is now co-maintaining the Amlogic Meson platform for both
32-bit and 64-bit ARM, and started contributing some patches.
- As is often the case, work on the OMAP platforms makes up the bulk of
the actual SoC code changes in arch/arm, but there isn't a lot of
that either.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5oFu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"We get support for three new 32-bit SoC platforms this time.
The amount of changes in arch/arm for any of them is miniscule, as all
the interesting code is in device driver subsystems (irqchip, clk,
pinctrl, ...) these days. I'm listing them here, as the addition of
the Kconfig statement is the main relevant milestone for a new
platform. In each case, some drivers are are shared with existing
platforms, while other drivers are added for v4.7 as well, or come in
a later release.
- The Aspeed platform is probably the most interesting one, this is
what most whitebox servers use as their baseboard management
controller. We get support for the very common ast2400 and ast2500
SoCs. The OpenBMC project focuses on this chip, and the LWN
article about their ELC 2016 presentation at
https://lwn.net/Articles/683320/
triggered the submission, but the code comes from IBM's OpenPOWER
team rather than the team at Facebook. There are still a lot more
drivers that need to get added over time, and I hope both teams can
work together on that.
- OXNAS is an old platform for Network Attached Storage devices from
Oxford Semiconductor. There are models with ARM10 (!) and
ARM11MPCore cores, but for now, we only support the original ARM9
based versions. The product lineup was subsequently part of PLX,
Avago and now the new Broadcom Ltd.
https://wiki.openwrt.org/doc/hardware/soc/soc.oxnas
has some more information.
- V2M-MPS2 is a prototyping platform from ARM for their Cortex-M
cores and is related to the existing Realview / Versatile Express
lineup, but without MMU.
We now support various NOMMU platforms, so adding a new one is
fairly straightforward.
http://infocenter.arm.com/help/topic/com.arm.doc.100112_0100_03_en/
has detailed information about the platform.
Other noteworthy updates:
- Work on LPC32xx has resumed, and Vladimir Zapolskiy and Sylvain
Lemieux are now maintaining the platform.
This is an older ARM9 based platform from NXP (not Freescale), but
it remains in use in embedded markets.
- Kevin Hilman is now co-maintaining the Amlogic Meson platform for
both 32-bit and 64-bit ARM, and started contributing some patches.
- As is often the case, work on the OMAP platforms makes up the bulk
of the actual SoC code changes in arch/arm, but there isn't a lot
of that either"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
MAINTAINERS: ARM/Amlogic: add co-maintainer, misc. updates
MAINTAINERS: add ARM/NXP LPC32XX SoC specific drivers to the section
MAINTAINERS: add new maintainers of NXP LPC32xx SoC
MAINTAINERS: move ARM/NXP LPC32xx record to ARM section
arm: Add Aspeed machine
ARM: lpc32xx: remove duplicate const on lpc32xx_auxdata_lookup
ARM: lpc32xx: remove leftovers of legacy clock source and provider drivers
ARM: lpc32xx: remove reboot header file
ARM: dove: Remove CLK_IS_ROOT
ARM: orion5x: Remove CLK_IS_ROOT
ARM: mv78xx0: Remove CLK_IS_ROOT
ARM: davinci: da850: use clk->set_parent for async3
ARM: davinci: Move clock init after ioremap.
MAINTAINERS: Update ARM Versatile Express platform entry
ARM: vexpress/mps2: introduce MPS2 platform
MAINTAINERS: add maintainer entry for ARM/OXNAS platform
ARM: Add new mach-oxnas
irqchip: versatile-fpga: add new compatible for OX810SE SoC
ARM: uniphier: correct the call order of of_node_put()
MAINTAINERS: fix stale TI DaVinci entries
...
Pull irq updates from Thomas Gleixner:
"This update delivers:
- Yet another interrupt chip diver (LPC32xx)
- Core functions to handle partitioned per-cpu interrupts
- Enhancements to the IPI core
- Proper handling of irq type configuration
- A large set of ARM GIC enhancements
- The usual pile of small fixes, cleanups and enhancements"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
irqchip/bcm2836: Use a more generic memory barrier call
irqchip/bcm2836: Fix compiler warning on 64-bit build
irqchip/bcm2836: Drop smp_set_ops on arm64 builds
irqchip/gic: Add helper functions for GIC setup and teardown
irqchip/gic: Store GIC configuration parameters
irqchip/gic: Pass GIC pointer to save/restore functions
irqchip/gic: Return an error if GIC initialisation fails
irqchip/gic: Remove static irq_chip definition for eoimode1
irqchip/gic: Don't initialise chip if mapping IO space fails
irqchip/gic: WARN if setting the interrupt type for a PPI fails
irqchip/gic: Don't unnecessarily write the IRQ configuration
irqchip: Mask the non-type/sense bits when translating an IRQ
genirq: Ensure IRQ descriptor is valid when setting-up the IRQ
irqchip/gic-v3: Configure all interrupts as non-secure Group-1
irqchip/gic-v2m: Add workaround for Broadcom NS2 GICv2m erratum
irqchip/irq-alpine-msi: Don't use <asm-generic/msi.h>
irqchip/mbigen: Checking for IS_ERR() instead of NULL
irqchip/gic-v3: Remove inexistant register definition
irqchip/gicv3-its: Don't allow devices whose ID is outside range
irqchip: Add LPC32xx interrupt controller driver
...
- virt_to_page/page_address optimisations
- Support for NUMA systems described using device-tree
- Support for hibernate/suspend-to-disk
- Proper support for maxcpus= command line parameter
- Detection and graceful handling of AArch64-only CPUs
- Miscellaneous cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJXNbgkAAoJELescNyEwWM0PtcIAK11xaOMmSqXz8fcTeNLw4dS
taaPWhjCYus8EhJyvTetfwk74+qVApdvKXKNKgODJXQEjeQx2brdUfbQZb31DTGT
798UYCAyEYCWkXspqi+/dpZEgUGPYH7uGOu2eDd19+PhTeX/EQSRX3fC9k0BNhvh
PN9pOgRcKAlIExZ6QYmT0g56VLtbCfFShN41mQ8HdpShl6pPJuhQ+kDDzudmRjuD
11/oYuOaVTnwbPuXn+sjOrWvMkfINHI70BAQnnBs0v+5c45mzpqEMsy0dYo2Pl2m
ar5lUFVIZggQkiqcOzqBzEgF+4gNw4LUu1DgK6cNKNMtL6k8E9zeOZMWeSVr0lg=
=bT5E
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
- virt_to_page/page_address optimisations
- support for NUMA systems described using device-tree
- support for hibernate/suspend-to-disk
- proper support for maxcpus= command line parameter
- detection and graceful handling of AArch64-only CPUs
- miscellaneous cleanups and non-critical fixes
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (92 commits)
arm64: do not enforce strict 16 byte alignment to stack pointer
arm64: kernel: Fix incorrect brk randomization
arm64: cpuinfo: Missing NULL terminator in compat_hwcap_str
arm64: secondary_start_kernel: Remove unnecessary barrier
arm64: Ensure pmd_present() returns false after pmd_mknotpresent()
arm64: Replace hard-coded values in the pmd/pud_bad() macros
arm64: Implement pmdp_set_access_flags() for hardware AF/DBM
arm64: Fix typo in the pmdp_huge_get_and_clear() definition
arm64: mm: remove unnecessary EXPORT_SYMBOL_GPL
arm64: always use STRICT_MM_TYPECHECKS
arm64: kvm: Fix kvm teardown for systems using the extended idmap
arm64: kaslr: increase randomization granularity
arm64: kconfig: drop CONFIG_RTC_LIB dependency
arm64: make ARCH_SUPPORTS_DEBUG_PAGEALLOC depend on !HIBERNATION
arm64: hibernate: Refuse to hibernate if the boot cpu is offline
arm64: kernel: Add support for hibernate/suspend-to-disk
PM / Hibernate: Call flush_icache_range() on pages restored in-place
arm64: Add new asm macro copy_page
arm64: Promote KERNEL_START/KERNEL_END definitions to a header file
arm64: kernel: Include _AC definition in page.h
...
Provide a gic_read_local_vp_id() function to read the VCNUM field of the
GICs local VP_IDENT register. This will be used by a further patch to
check that the value reported by the GIC matches up with the kernels
calculation.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Linux CPU number doesn't necessarily match up with the ID used for a
VP by hardware. Convert the CPU number to the HW ID using mips_cm_vp_id
when writing to the VP(E)_OTHER_ADDR register in order to ensure that we
correctly access registers for the VPs of secondary cores. This most
notably affects systems using CM3, such as those based around I6400.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
dsb() requires an argument on arm64, so we needed to add "sy".
Instead, take this opportunity to switch to the same smp_wmb() call
that gic uses for its IPIs. This is a less strong barrier than we
were doing before (dmb(ishst) compared to dsb(sy)), but it seems to be
the correct one.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
For arm64, the bootloader will instead be implementing the spin-table
enable method.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Move the code that sets-up a GIC via device-tree into it's own
function and add a generic function for GIC teardown that can be used
for both device-tree and ACPI to unmap the GIC memory.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Store the GIC configuration parameters in the GIC chip data structure.
This will allow us to simplify the code by reducing the number of
parameters passed between functions.
Update the __gic_init_bases() function so that we only need to pass a
pointer to the GIC chip data structure and no longer need to pass the
GIC index in order to look-up the chip data.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of passing the GIC index to the save/restore functions pass a
pointer to the GIC chip data. This will allow these save/restore
functions to be re-used by a platform driver where the GIC chip data
structure is allocated dynamically and so there is no applicable index
for identifying the GIC.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the GIC initialisation fails, then currently we do not return an error
or clean-up afterwards. Although for root controllers, this failure may be
fatal anyway, for secondary controllers, it may not be fatal and so return
an error on failure and clean-up.
Update the functions gic_cpu_init() and gic_pm_init() to return an error
instead of calling BUG() and perform any necessary clean-up.
For non-banked GIC controllers, make sure that we free any memory
allocated if we fail to initialise the IRQ domain. Please note that
free_percpu() only frees memory if the pointer passed to it is not NULL
and so it is unnecessary to check if both pointers are valid or not.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There are only 3 differences (not including the name) in the definitions
of the gic_chip and gic_eoimode1_chip structures. Instead of statically
defining the gic_eoimode1_chip structure, remove it and populate the
eoimode1 functions dynamically for the appropriate GIC irqchips.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If we fail to map the address space for the GIC distributor or CPU
interface, then don't attempt to initialise the chip, just WARN and
return.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Setting the interrupt type for private peripheral interrupts (PPIs) may
not be supported by a given GIC because it is IMPLEMENTATION DEFINED
whether this is allowed. There is no way to know if setting the type is
supported for a given GIC and so the value written is read back to
verify it matches the desired configuration. If it does not match then
an error is return.
There are cases where the interrupt configuration read from firmware
(such as a device-tree blob), has been incorrect and hence
gic_configure_irq() has returned an error. This error has gone
undetected because the error code returned was ignored but the interrupt
still worked fine because the configuration for the interrupt could not
be overwritten.
Given that this has done undetected and that failing to set the
configuration for a PPI may not be a catastrophic, don't return an error
but WARN if we fail to configure a PPI. This will allows us to fix up
any places in the kernel where we should be checking the return status
and maintain backward compatibility with firmware images that may have
incorrect PPI configurations.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the interrupt configuration matches the current configuration, then
don't bother writing the configuration again.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The firmware parameter that contains the IRQ sense bits may also contain
other data. When return the IRQ type, bits outside of these sense bits
should be masked. If these bits are not masked and
irq_create_fwspec_mapping() is called to map an IRQ, then the comparison
of the type returned from irq_domain_translate() will never match
that returned by irq_get_trigger_type() (because this function masks the
none sense bits) and so we will always call irq_set_irq_type() to program
the type even if it was not really necessary.
Currently, the downside to this is unnecessarily re-programmming the type
but nevertheless this should be avoided.
The Tegra LIC and TI Crossbar irqchips all have client instances (from
reviewing the device-tree sources) where bits outside the IRQ sense bits
are set, but do not mask these bits. Therefore, ensure these bits are
masked for these irqchips.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The GICv3 driver wrongly assumes that it runs on the non-secure
side of a secure-enabled system, while it could be on a system
with a single security state, or a GICv3 with GICD_CTLR.DS set.
Either way, it is important to configure this properly, or
interrupts will simply not be delivered on this HW.
Cc: stable@vger.kernel.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Alex Barba <alex.barba@broadcom.com> discovered Broadcom NS2 GICv2m
implementation has an erratum where the MSI data needs to be the SPI
number subtracted by an offset of 32, for the correct MSI interrupt
to be triggered.
Here we are adding the workaround based on readings from the MSI_IIDR
register, which contains a value unique to Broadcom NS2 GICv2m
Reported-by: Alex Barba <alex.barba@broadcom.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
of_platform_device_create() returns NULL on error, it never returns
error pointers.
Fixes: ed2a1002d2 ('irqchip/mbigen: Handle multiple device nodes in a mbigen module')
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We are not checking whether the requested device identifier fits into
the device table memory or not. The function its_create_device()
assumes that enough memory has been allocated for whole DevID space
(reported by ITS_TYPER.Devbits) during the ITS probe() and continues
to initialize ITS hardware.
This assumption is not perfect, sometimes we reduce memory size either
because of its size crossing MAX_ORDER-1 or BASERn max size limit. The
MAPD command fails if 'Device ID' is outside of device table range.
Add a simple validation check to avoid MAPD failures since we are
not handling ITS command errors. This change also helps to return an
error -ENOMEM instead of success to caller.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The change adds improved support of NXP LPC32xx MIC, SIC1 and SIC2
interrupt controllers.
This is a list of new features in comparison to the legacy driver:
* irq types are taken from device tree settings, no more need to
hardcode them,
* old driver is based on irq_domain_add_legacy, which causes problems
with handling MIC hardware interrupt 0 produced by SIC1,
* there is one driver for MIC, SIC1 and SIC2, no more need to handle
them separately, e.g. have two separate handlers for SIC1 and SIC2,
* the driver does not have any dependencies on hardcoded register
offsets,
* the driver is much simpler for maintenance,
* SPARSE_IRQS option is supported.
Legacy LPC32xx interrupt controller driver was broken since commit
76ba59f836 ("genirq: Add irq_domain-aware core IRQ handler"), which
requires a private interrupt handler, otherwise any SIC1 generated
interrupt (mapped to MIC hwirq 0) breaks the kernel with the message
"unexpected IRQ trap at vector 00".
The change disables compilation of a legacy driver found at
arch/arm/mach-lpc32xx/irq.c, the file will be removed in a separate
commit.
Fixes: 76ba59f836 ("genirq: Add irq_domain-aware core IRQ handler")
Tested-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When an IPI is generated by a CPU, the pattern looks roughly like:
<write shared data>
smp_wmb();
<write to GIC to signal SGI>
On the receiving CPU we rely on the fact that, once we've taken the
interrupt, then the freshly written shared data must be visible to us.
Put another way, the CPU isn't going to speculate taking an interrupt.
Unfortunately, this assumption turns out to be broken.
Consider that CPUx wants to send an IPI to CPUy, which will cause CPUy
to read some shared_data. Before CPUx has done anything, a random
peripheral raises an IRQ to the GIC and the IRQ line on CPUy is raised.
CPUy then takes the IRQ and starts executing the entry code, heading
towards gic_handle_irq. Furthermore, let's assume that a bunch of the
previous interrupts handled by CPUy were SGIs, so the branch predictor
kicks in and speculates that irqnr will be <16 and we're likely to
head into handle_IPI. The prefetcher then grabs a speculative copy of
shared_data which contains a stale value.
Meanwhile, CPUx gets round to updating shared_data and asking the GIC
to send an SGI to CPUy. Internally, the GIC decides that the SGI is
more important than the peripheral interrupt (which hasn't yet been
ACKed) but doesn't need to do anything to CPUy, because the IRQ line
is already raised.
CPUy then reads the ACK register on the GIC, sees the SGI value which
confirms the branch prediction and we end up with a stale shared_data
value.
This patch fixes the problem by adding an smp_rmb() to the IPI entry
code in gic_handle_irq. As it turns out, the combination of a control
dependency and an ISB instruction from the EOI in the GICv3 driver is
enough to provide the ordering we need, so we add a comment there
justifying the absence of an explicit smp_rmb().
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Adding EZchip NPS400 support.
Internal interrupts are handled by Multi Thread Manager (MTM)
Once interrupt is serviced MTM is acked for deactivating the interrupt.
External interrupts are handled by MTM as well as at Global Interrupt
Controller (GIC) e.g. serial and network devices.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Paul Burton