Add the Amlogic SM1 based Khadas VIM3L, sharing all the same features
as the G12B based VIM3, but:
- a different DVFS support since only a single cluster is available
- audio is still not available on SM1
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
To prepare support of the Amlogic SM1 based Khadas VIM3, move the non-G12B
specific nodes (all except DVFS and Audio) to a new meson-khadas-vim3.dtsi
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the reset to the TDM formatters of the g12a. This helps
with channel mapping when a playback/capture uses more than 1 lane.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock controller dedicated to audio clocks also provides reset lines
on the g12 SoC family
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This enables DVFS for the Amlogic SM1 based SEI610 board by:
- Adding the SM1 SoC OPPs taken from the vendor tree
- Selecting the SM1 Clock controller instead of the G12A one
- Adding the CPU rail regulator, PWM and OPPs for each CPU nodes.
Each power supply can achieve 0.69V to 1.05V using a single PWM
output clocked at 666KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations of the cpu cluster and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Swap to the rc-khadas keymap that maps the mouse button to KEY_MUTE.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the rc-tx3mini keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Swap to the rc-khadas keymap that maps the mouse button to KEY_MUTE.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the rc-wetek-play2 keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the rc-wetek-hub keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the rc-x96max keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the rc-odroid keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the USB properties for the Amlogic SM1 Based SEI610 Board in order to
support the USB DRD Type-C port and the USB3 Type A port.
The USB DRD Type-C controller uses the ID signal to toggle the USB role
between the DWC3 Host controller and the DWC2 Device controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the HDMI support nodes for the Amlogic SM1 Based SEI610 Board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Replace the VPU-centric power domain controller by the generic system-wide
Everything-Else power domain controller and setup the right power-domains
properties on the VPU, Ethernet & USB nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[khilman: minor subject edit: add dts]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected)
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long
meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected)
meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long
meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-p201.dt.yaml: ethernet@c9410000: snps,reset-delays-us: [[0, 10000, 1000000]] is too short
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: /: 'model' is a required property
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-g12a-x96-max.dt.yaml: /: compatible: ['amediatech,x96-max', 'amlogic,u200', 'amlogic,g12a'] is not valid under any of the given schemas
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-g12a-u200.dt.yaml: reset-controller@1004: compatible:0: 'amlogic,meson-g12a-reset' is not one of ['amlogic,meson8b-reset', 'amlogic,meson-gxbb-reset', 'amlogic,meson-axg-reset']
meson-g12a-sei510.dt.yaml: reset-controller@1004: compatible:0: 'amlogic,meson-g12a-reset' is not one of ['amlogic,meson8b-reset', 'amlogic,meson-gxbb-reset', 'amlogic,meson-axg-reset']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-axg-s400.dt.yaml: mailbox@ff63c404: compatible:0: 'amlogic,meson-gx-mhu' is not one of ['amlogic,meson-gxbb-mhu']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxl-s805x-libretech-ac.dt.yaml: ethernet-phy@8: compatible: ['ethernet-phy-id0181.4400', 'ethernet-phy-ieee802.3-c22'] is not valid under any of the given schemas
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: periphs@c8834000: $nodename:0: 'periphs@c8834000' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
meson-gxl-s805x-libretech-ac.dt.yaml: periphs@c8834000: $nodename:0: 'periphs@c8834000' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: mailbox@404: compatible:0: 'amlogic,meson-gx-mhu' is not one of ['amlogic,meson-gxbb-mhu']
meson-gxl-s805x-libretech-ac.dt.yaml: mailbox@404: compatible:0: 'amlogic,meson-gx-mhu' is not one of ['amlogic,meson-gxbb-mhu']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: watchdog@98d0: compatible:0: 'amlogic,meson-gx-wdt' is not one of ['amlogic,meson-gxbb-wdt']
meson-gxl-s805x-libretech-ac.dt.yaml: watchdog@98d0: compatible:0: 'amlogic,meson-gx-wdt' is not one of ['amlogic,meson-gxbb-wdt']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxl-s805x-libretech-ac.dt.yaml: spi@8c80: compatible:0: 'amlogic,meson-gx-spifc' is not one of ['amlogic,meson6-spifc', 'amlogic,meson-gxbb-spifc']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: reset-controller@4404: compatible:0: 'amlogic,meson-gx-reset' is not one of ['amlogic,meson8b-reset', 'amlogic,meson-gxbb-reset', 'amlogic,meson-axg-reset']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxl-s805x-libretech-ac.dt.yaml: vpu@d0100000: reg-names: Additional items are not allowed ('dmc' was unexpected)
meson-gxl-s805x-libretech-ac.dt.yaml: vpu@d0100000: reg-names: ['vpu', 'hhi', 'dmc'] is too long
The 'dmc' register area was replaced by the amlogic,canvas property
which was introduced in commit f172604342 ("arm64: dts: meson-gx:
add dmcbus and canvas nodes.") and commit cf34287986 ("arm64: dts:
meson-gx: Add canvas provider node to the vpu")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-axg-s400.dt.yaml: soc: ethernet@ff3f0000:reg:0: [0, 4282318848, 0, 65536, 0, 4284695872, 0, 8] is too long
meson-axg-s400.dt.yaml: ethernet@ff3f0000: reg: [[0, 4282318848, 0, 65536, 0, 4284695872, 0, 8]] is too short
meson-g12a-u200.dt.yaml: soc: ethernet@ff3f0000:reg:0: [0, 4282318848, 0, 65536, 0, 4284695872, 0, 8] is too long
meson-g12a-u200.dt.yaml: ethernet@ff3f0000: reg: [[0, 4282318848, 0, 65536, 0, 4284695872, 0, 8]] is too short
meson-gxbb-nanopi-k2.dt.yaml: soc: ethernet@c9410000:reg:0: [0, 3376480256, 0, 65536, 0, 3364046144, 0, 4] is too long
meson-gxl-s805x-libretech-ac.dt.yaml: soc: ethernet@c9410000:reg:0: [0, 3376480256, 0, 65536, 0, 3364046144, 0, 4] is too lon
while here, also drop the redundant reg property from meson-gxl.dtsi
because it had the same value as meson-gx.dtsi from which it inherits.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
We no longer fall back to out-of-line atomics on systems with
CONFIG_ARM64_LSE_ATOMICS where ARM64_HAS_LSE_ATOMICS is not set.
Remove the unused compilation unit which provided these symbols.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Now that we have removed the out-of-line ll/sc atomics we can give
the compiler the freedom to choose its own register allocation.
Remove the hard-coded use of x30.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
When building for LSE atomics (CONFIG_ARM64_LSE_ATOMICS), if the hardware
or toolchain doesn't support it the existing code will fallback to ll/sc
atomics. It achieves this by branching from inline assembly to a function
that is built with special compile flags. Further this results in the
clobbering of registers even when the fallback isn't used increasing
register pressure.
Improve this by providing inline implementations of both LSE and
ll/sc and use a static key to select between them, which allows for the
compiler to generate better atomics code. Put the LL/SC fallback atomics
in their own subsection to improve icache performance.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Based on an email from Will Deacon.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
The memory allocated for the atomic pool needs to have the same
mapping attributes that we use for remapping, so use
pgprot_dmacoherent instead of open coding it. Also deduct a
suitable zone to allocate the memory from based on the presence
of the DMA zones.
Signed-off-by: Christoph Hellwig <hch@lst.de>
arch_dma_mmap_pgprot is used for two things:
1) to override the "normal" uncached page attributes for mapping
memory coherent to devices that can't snoop the CPU caches
2) to provide the special DMA_ATTR_WRITE_COMBINE semantics on older
arm systems and some mips platforms
Replace one with the pgprot_dmacoherent macro that is already provided
by arm and much simpler to use, and lift the DMA_ATTR_WRITE_COMBINE
handling to common code with an explicit arch opt-in.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> # m68k
Acked-by: Paul Burton <paul.burton@mips.com> # mips
The A64 ISA accepts distinct (but overlapping) ranges of immediates for:
* add arithmetic instructions ('I' machine constraint)
* sub arithmetic instructions ('J' machine constraint)
* 32-bit logical instructions ('K' machine constraint)
* 64-bit logical instructions ('L' machine constraint)
... but we currently use the 'I' constraint for many atomic operations
using sub or logical instructions, which is not always valid.
When CONFIG_ARM64_LSE_ATOMICS is not set, this allows invalid immediates
to be passed to instructions, potentially resulting in a build failure.
When CONFIG_ARM64_LSE_ATOMICS is selected the out-of-line ll/sc atomics
always use a register as they have no visibility of the value passed by
the caller.
This patch adds a constraint parameter to the ATOMIC_xx and
__CMPXCHG_CASE macros so that we can pass appropriate constraints for
each case, with uses updated accordingly.
Unfortunately prior to GCC 8.1.0 the 'K' constraint erroneously accepted
'4294967295', so we must instead force the use of a register.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
The gic-its node unit-address has an additional zero compared
to the actual reg value. Fix it.
Fixes: 2d87061e70 ("arm64: dts: ti: Add Support for J721E SoC")
Reported-by: Robert Tivy <rtivy@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The gic-its node unit-address has an additional zero compared
to the actual reg value. Fix it.
Fixes: ea47eed33a ("arm64: dts: ti: Add Support for AM654 SoC")
Reported-by: Robert Tivy <rtivy@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The Main NavSS block on J721E SoCs contains a HwSpinlock IP instance that
is same as the IP on AM65x SoCs and similar to the IP on some OMAP SoCs.
Add the DT node for this on J721E SoCs. The node is present within the
Main NavSS block, and is added as a child node under the cbass_main_navss
interconnect node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The Main NavSS block on AM65x SoCs contains a HwSpinlock IP instance
that is similar to the IP on some OMAP SoCs. Add the DT node for this
on AM65x SoCs. The node is present within the NavSS block, and is
added as a child node under the cbass_main_navss interconnect node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Common processor board for K3 J721E platform has two push buttons
namely SW10 and SW11.
Add a gpio-keys device node to model them as input keys in Linux.
Add required pinmux nodes to set GPIO pins as input.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There are 10 gpio instances inside SoC with 3 groups as below:
- Group1: main_gpio0, main_gpio2, main_gpio4, main_gpio6
- Group2: main_gpio1, main_gpio3, main_gpio5, main_gpio7
- Group3: wkup_gpio0, wkup_gpio1
Only one instance can be used in each group at a time. So use main_gpio0,
main_gpio1 and wkup_gpio0 for the current linux context and mark other
gpio nodes as disabled.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Similar to the gpio groups in main domain, there is one gpio group
in wakup domain with 2 module instances in it. This gpio group pins
out 84 lines(6 banks). Add DT node for these 2 gpio module instances.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There are 8 instances of gpio modules in main domain divided into 2 groups:
- Group1: gpio0, gpio2, gpio4, gpio6
- Group2: gpio1, gpio3, gpio5, gpio7
Groups are created to provide protection between two different processor
virtual worlds. There are x gpio lines coming out of each group. Each module
in a group has equal x gpio lines pinned out. There is a top level mux for
selecting the module instance for each pin coming out of group. Exactly
one module can be selected to control the corresponding pin. This muxing
can be controlled along the pad mux configuration registers.
Group1 pins out 128 lines(8 banks). Group 2 pins out 36 lines(2 banks).
Add DT nodes for each module instance in the main domain. Users should
make sure that correct gpio instance is selected in their pad configuration.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Update the power-domain cells to 2 and mark all devices as
exclusive. Main uart 0 is the debug console for processor boards
and it is used by different software entities like u-boot, atf,
linux simultaneously. So just mark main_uart0 as shared device
for common processor board.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Update the power-domain cells to 2 and mark all devices as
exclusive. Main uart 0 is the debug console for based boards
and it is used by different software entities like u-boot, atf,
linux. So just mark main_uart0 as shared device for base board.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
While the MMUs is disabled, I-cache speculation can result in
instructions being fetched from the PoC. During boot we may patch
instructions (e.g. for alternatives and jump labels), and these may be
dirty at the PoU (and stale at the PoC).
Thus, while the MMU is disabled in the KPTI pagetable fixup code we may
load stale instructions into the I-cache, potentially leading to
subsequent crashes when executing regions of code which have been
modified at runtime.
Similarly to commit:
8ec4198743 ("arm64: mm: ensure patched kernel text is fetched from PoU")
... we can invalidate the I-cache after enabling the MMU to prevent such
issues.
The KPTI pagetable fixup code itself should be clean to the PoC per the
boot protocol, so no maintenance is required for this code.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
With 16K pages and 48-bit VAs, the PGD level of table has two entries,
and so the fixmap shares a PGD with the kernel image. Since commit:
f9040773b7 ("arm64: move kernel image to base of vmalloc area")
... we copy the existing fixmap to the new fine-grained page tables at
the PUD level in this case. When walking to the new PUD, we forgot to
offset the PGD entry and always used the PGD entry at index 0, but this
worked as the kernel image and fixmap were in the low half of the TTBR1
address space.
As of commit:
14c127c957 ("arm64: mm: Flip kernel VA space")
... the kernel image and fixmap are in the high half of the TTBR1
address space, and hence use the PGD at index 1, but we didn't update
the fixmap copying code to account for this.
Thus, we'll erroneously try to copy the fixmap slots into a PUD under
the PGD entry at index 0. At the point we do so this PGD entry has not
been initialised, and thus we'll try to write a value to a small offset
from physical address 0, causing a number of potential problems.
Fix this be correctly offsetting the PGD. This is split over a few steps
for legibility.
Fixes: 14c127c957 ("arm64: mm: Flip kernel VA space")
Reported-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Steve Capper <Steve.Capper@arm.com>
Tested-by: Steve Capper <Steve.Capper@arm.com>
Tested-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
This patch the removes the recently added mediatek,physpeed property.
Use the fixed-link property speed = <2500> to set the phy in 2.5Gbit.
See mt7622-bananapi-bpi-r64.dts for a working example.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f6ea23f63 ("arm64: KVM: Avoid marking pages as XN in
Stage-2 if CTR_EL0.DIC is set"), KVM has stopped marking normal memory
as execute-never at stage2 when the system supports D->I Coherency at
the PoU. This avoids KVM taking a trap when the page is first executed,
in order to clean it to PoU.
The patch that added this change also wrapped PAGE_S2_DEVICE mappings
up in this too. The upshot is, if your CPU caches support DIC ...
you can execute devices.
Revert the PAGE_S2_DEVICE change so PTE_S2_XN is always used
directly.
Fixes: 2f6ea23f63 ("arm64: KVM: Avoid marking pages as XN in Stage-2 if CTR_EL0.DIC is set")
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Now that we have a definition for the 'F' field of PAR_EL1, use that
instead of coding the immediate directly.
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Thanks to address translation being performed out of order with respect to
loads and stores, it is possible for a CPU to take a translation fault when
accessing a page that was mapped by a different CPU.
For example, in the case that one CPU maps a page and then sets a flag to
tell another CPU:
CPU 0
-----
MOV X0, <valid pte>
STR X0, [Xptep] // Store new PTE to page table
DSB ISHST
ISB
MOV X1, #1
STR X1, [Xflag] // Set the flag
CPU 1
-----
loop: LDAR X0, [Xflag] // Poll flag with Acquire semantics
CBZ X0, loop
LDR X1, [X2] // Translates using the new PTE
then the final load on CPU 1 can raise a translation fault because the
translation can be performed speculatively before the read of the flag and
marked as "faulting" by the CPU. This isn't quite as bad as it sounds
since, in reality, code such as:
CPU 0 CPU 1
----- -----
spin_lock(&lock); spin_lock(&lock);
*ptr = vmalloc(size); if (*ptr)
spin_unlock(&lock); foo = **ptr;
spin_unlock(&lock);
will not trigger the fault because there is an address dependency on CPU 1
which prevents the speculative translation. However, more exotic code where
the virtual address is known ahead of time, such as:
CPU 0 CPU 1
----- -----
spin_lock(&lock); spin_lock(&lock);
set_fixmap(0, paddr, prot); if (mapped)
mapped = true; foo = *fix_to_virt(0);
spin_unlock(&lock); spin_unlock(&lock);
could fault. This can be avoided by any of:
* Introducing broadcast TLB maintenance on the map path
* Adding a DSB;ISB sequence after checking a flag which indicates
that a virtual address is now mapped
* Handling the spurious fault
Given that we have never observed a problem due to this under Linux and
future revisions of the architecture are being tightened so that
translation table walks are effectively ordered in the same way as explicit
memory accesses, we no longer treat spurious kernel faults as fatal if an
AT instruction indicates that the access does not trigger a translation
fault.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
PAR_EL1 is a mysterious creature, but sometimes it's necessary to read
it when translating addresses in situations where we cannot walk the
page table directly.
Add a couple of system register definitions for the fault indication
field ('F') and the fault status code ('FST').
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Commit 6a4cbd63c25a ("Revert "arm64: Remove unnecessary ISBs from
set_{pte,pmd,pud}"") reintroduced ISB instructions to some of our
page table setter functions in light of a recent clarification to the
Armv8 architecture. Although 'set_pgd()' isn't currently used to update
a live page table, add the ISB instruction there too for consistency
with the other macros and to provide some future-proofing if we use it
on live tables in the future.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
05f2d2f83b ("arm64: tlbflush: Introduce __flush_tlb_kernel_pgtable")
added a new TLB invalidation helper which is used when freeing
intermediate levels of page table used for kernel mappings, but is
missing the required ISB instruction after completion of the TLBI
instruction.
Add the missing barrier.
Cc: <stable@vger.kernel.org>
Fixes: 05f2d2f83b ("arm64: tlbflush: Introduce __flush_tlb_kernel_pgtable")
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
This reverts commit 24fe1b0efa.
Commit 24fe1b0efa ("arm64: Remove unnecessary ISBs from
set_{pte,pmd,pud}") removed ISB instructions immediately following updates
to the page table, on the grounds that they are not required by the
architecture and a DSB alone is sufficient to ensure that subsequent data
accesses use the new translation:
DDI0487E_a, B2-128:
| ... no instruction that appears in program order after the DSB
| instruction can alter any state of the system or perform any part of
| its functionality until the DSB completes other than:
|
| * Being fetched from memory and decoded
| * Reading the general-purpose, SIMD and floating-point,
| Special-purpose, or System registers that are directly or indirectly
| read without causing side-effects.
However, the same document also states the following:
DDI0487E_a, B2-125:
| DMB and DSB instructions affect reads and writes to the memory system
| generated by Load/Store instructions and data or unified cache
| maintenance instructions being executed by the PE. Instruction fetches
| or accesses caused by a hardware translation table access are not
| explicit accesses.
which appears to claim that the DSB alone is insufficient. Unfortunately,
some CPU designers have followed the second clause above, whereas in Linux
we've been relying on the first. This means that our mapping sequence:
MOV X0, <valid pte>
STR X0, [Xptep] // Store new PTE to page table
DSB ISHST
LDR X1, [X2] // Translates using the new PTE
can actually raise a translation fault on the load instruction because the
translation can be performed speculatively before the page table update and
then marked as "faulting" by the CPU. For user PTEs, this is ok because we
can handle the spurious fault, but for kernel PTEs and intermediate table
entries this results in a panic().
Revert the offending commit to reintroduce the missing barriers.
Cc: <stable@vger.kernel.org>
Fixes: 24fe1b0efa ("arm64: Remove unnecessary ISBs from set_{pte,pmd,pud}")
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
When we fail to bring a secondary CPU online and it fails in an unknown
state, we should assume the worst and increment 'cpus_stuck_in_kernel'
so that things like kexec() are disabled.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Although SMP bringup is inherently racy, we can significantly reduce
the window during which secondary CPUs can unexpectedly enter the
kernel by sanity checking the 'stack' and 'task' fields of the
'secondary_data' structure. If the booting CPU gave up waiting for us,
then they will have been cleared to NULL and we should spin in a WFE; WFI
loop instead.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
When many debug options are enabled simultaneously (e.g. PROVE_LOCKING,
KMEMLEAK, DEBUG_PAGE_ALLOC, KASAN etc), it is possible for us to timeout
when attempting to boot a secondary CPU and give up. Unfortunately, the
CPU will /eventually/ appear, and sit in the background happily stuck
in a recursive exception due to a NULL stack pointer.
Increase the timeout to 5s, which will of course be enough for anybody.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Update Aramda 7k/8k DTs to use the phy-supply property of the (recent)
generic PHY framework instead of the (legacy) usb-phy preperty. Both
enable the supply when the PHY is enabled.
The COMPHY nodes only provide SERDES lanes configuration. The power
supply that is represented by the phy-supply property is just a
regulator wired to the USB connector, hence the creation of connector
nodes as child of the COMPHY nodes and the supply attached to it.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fill-in the missing PCIe phys/phy-names DT properties of Armada 7k/8k
based boards.
The MacchiatoBin is a bit particular as the Armada8k-PCI IP supports
x4 link widths and in this case the PHY for each lane must be
referenced.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fill-in the missing USB3 phys/phy-names DT properties of Armada 7k/8k
based boards. Only update nodes actually enabling USB3 in the default
(mainline) configuration. A few USB nodes are enabled but there is
only USB2 working on them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fill-in the missing SATA phys/phy-names DT properties of Armada 7k/8k
based boards.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds the rWTM BIU mailbox node for communication with the secure
processor. The driver already exists in
drivers/mailbox/armada-37xx-rwtm-mailbox.c.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
RPM clock controller has parent as xo, so specify that in DT node for
rpmhcc
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The SolidRun Hummingboard Pulse carrier board carries the SolidRun
i.MX8MQ based SOM.
Notably missing is PCIe support that depends on analog PLLOUT clock.
Current imx clk driver does not support this clock.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the spi-flash nodes under the DSPI controller for
ls1088a-qds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the DSPI controller node for ls1088a boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adding "rng-seed" to dtb. It's fine to add this property if original
fdt doesn't contain it. Since original seed will be wiped after
read, so use a default size 128 bytes here.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Will Deacon <will@kernel.org>
Currently in arm64, FDT is mapped to RO before it's passed to
early_init_dt_scan(). However, there might be some codes
(eg. commit "fdt: add support for rng-seed") that need to modify FDT
during init. Map FDT to RO after early fixups are done.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called
bcm43356 and can be used with the brcmfmac driver. The module is powered by
the two always on regulators (not AXP805).
WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
configured so that it sets up an 1.8V input bias on this port. This is done
by the pio driver by reading the vcc-pg-supply voltage.
You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
configuration that can be found in the Xulongs's repository for H6:
https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256
Mainline brcmfmac driver expects the firmware and nvram at the following
paths relative to the firmware directory:
brcm/brcmfmac43456-sdio.bin
brcm/brcmfmac43456-sdio.txt
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The watchdog has a clock on all our SoCs, but it wasn't always listed.
Add it to the devicetree where it's missing.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch adds RTC node and fixes the clock properties and nodes
to reflect the real clock tree.
The device nodes for the internal oscillator and osc32k are removed,
as these clocks are now provided by the RTC device. Clock references
are fixed accordingly, too.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain.
Basic benchmarks using Flexible IO Tester show reasonable performance from the
eMMC.
eMMC - Random Write: 21.3MiB/s
eMMC - Sequential Write: 68.2MiB/s
SD Card - Random Write: 1690KiB/s
SD Card - Sequential Write: 11.0MiB/s
Changes:
v3: Separate dts for eMMC variants
v2: Fix descriptions for VCC and VCCQ
Link: 174953de1e
Signed-off-by: Martin Ayotte <martinayotte@gmail.com>
[sunil@medhas.org Fix descriptions for VCC and VCCQ, separate dts for eMMC]
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
Tested-by: Sunil Mohan Adapa <sunil@medhas.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB useable)
- 100Mbps EMAC via AC200 EPHY
- Cdtech 47822BS Wifi/BT
- 2x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- IR receiver
- 64GiB eMMC
- 5V/2A DC power supply
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add device-tree nodes for i2c0 to i2c2, and also add relevant pinctrl
nodes.
Suggested-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1 has a DDC I2C bus voltage shifter. This is actually missing
and video is limited to 1024x768 due to missing EDID information.
Add the DDC regulator in the device-tree.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1 board has a SPDIF out connector, so enable it in
the device-tree and add a simple SPDIF soundcard.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 has a SPDIF controller called OWA (One Wire Audio).
Only one pinmuxing is available so set it as default.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Orange Pi 3 has a DDC_CEC_EN signal connected to PH2, that enables the DDC
I2C bus voltage shifter. Before EDID can be read, we need to pull PH2 high.
This is realized by the ddc-en-gpios property.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Remove the num-lanes property to avoid the driver setting the
link width.
On FSL Layerscape SoCs, the number of lanes assigned to PCIe
controller is not fixed, it is determined by the selected SerDes
protocol in the RCW (Reset Configuration Word).
The PCIe link training is completed automatically through the selected
SerDes protocol - the link width set-up is updated by hardware after
power on reset, so the num-lanes property is not needed for Layerscape
PCIe.
The current num-lanes property was added erroneously, which actually
indicates the maximum lanes the PCIe controller can support up to,
instead of the lanes assigned to the PCIe controller. The link width set
by SerDes protocol will be overridden by the num-lanes property, hence
the subsequent re-training will fail when the assigned lanes do not
match the value in the num-lanes property.
Remove the property to fix the issue
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Enable GCC config CONFIG_SM_GCC_8150 and pinctrl config
CONFIG_PINCTRL_SM8150 to make it possible to boot the SM8150 MTP.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The correct gic number of pwrap is 185 instead of 209. This patch fixes
it to avoid triggering error interrupt.
Fixes: e526c9bc11 ("arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and Makefile")
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the regulators found in the mtp platform. This platform consists of
pmic PM8150, PM8150L and PM8009.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This add base DTS file for sm8150-mtp and enables boot to console, adds
tlmm reserved range, resin node, volume down key and also includes pmic
file.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PMIC pm8150l is a slave pmic and this adds base DTS file for pm8150l
with power-on, adc and gpio nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PMIC pm8150b is a slave pmic and this adds base DTS file for pm8150b
with power-on, adc, and gpio nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add base DTS file for pm8150 along with GPIOs, power-on, rtc and vadc
nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This add base DTS file with cpu, psci, firmware, clock node tlmm and
spmi and enables boot to console
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add fastrpc compute context bank nodes to both cdsp and adsp.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use the standard obj-y form to specify the sub-directories under
arch/arm64/. No functional change intended.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Will Deacon <will@kernel.org>
When taking an SError or Debug exception from EL0, we run the C
handler for these exceptions before updating the context tracking
code and unmasking lower priority interrupts.
When booting with nohz_full lockdep tells us we got this wrong:
| =============================
| WARNING: suspicious RCU usage
| 5.3.0-rc2-00010-gb4b5e9dcb11b-dirty #11271 Not tainted
| -----------------------------
| include/linux/rcupdate.h:643 rcu_read_unlock() used illegally wh!
|
| other info that might help us debug this:
|
|
| RCU used illegally from idle CPU!
| rcu_scheduler_active = 2, debug_locks = 1
| RCU used illegally from extended quiescent state!
| 1 lock held by a.out/432:
| #0: 00000000c7a79515 (rcu_read_lock){....}, at: brk_handler+0x00
|
| stack backtrace:
| CPU: 1 PID: 432 Comm: a.out Not tainted 5.3.0-rc2-00010-gb4b5e9d1
| Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno De8
| Call trace:
| dump_backtrace+0x0/0x140
| show_stack+0x14/0x20
| dump_stack+0xbc/0x104
| lockdep_rcu_suspicious+0xf8/0x108
| brk_handler+0x164/0x1b0
| do_debug_exception+0x11c/0x278
| el0_dbg+0x14/0x20
Moving the ct_user_exit calls to be before do_debug_exception() means
they are also before trace_hardirqs_off() has been updated. Add a new
ct_user_exit_irqoff macro to avoid the context-tracking code using
irqsave/restore before we've updated trace_hardirqs_off(). To be
consistent, do this everywhere.
The C helper is called enter_from_user_mode() to match x86 in the hope
we can merge them into kernel/context_tracking.c later.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Fixes: 6c81fe7925 ("arm64: enable context tracking")
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Add CONFIG_ASM_MODVERSIONS. This allows to remove one if-conditional
nesting in scripts/Makefile.build.
scripts/Makefile.build is run every time Kbuild descends into a
sub-directory. So, I want to avoid $(wildcard ...) evaluation
where possible although computing $(wildcard ...) is so cheap that
it may not make measurable performance difference.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Update the 'vsps' property in the R-Car Gen3 SoC device tree files to
match what's in the documentation example.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently, the timestamp of module linker scripts are not checked.
Add them to the dependency of modules so they are correctly rebuilt.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since the R8A774C0 SoC uses DU{0,1} only, the register block length
should be 0x40000.
Based on commit 06585ed38b ("arm64: dts: renesas: r8a77990: Fix
register range of display node") for R-Car E3.
Fixes: 8ed3a6b223 ("arm64: dts: renesas: r8a774c0: Add display output support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the Amlogic SM1 Based SEI610 board.
The SM1 SoC is a derivative of the G12A SoC Family with :
- Cortex-A55 core instead of A53
- more power domains, including USB & PCIe
- a neural network co-processor (NNA)
- a CSI input and image processor
- some changes in the audio complex, thus not yet enabled
The SEI610 board is a derivative of the SEI510 board with :
- removed ADC based touch button, replaced with 3x GPIO buttons
- physical switch disabling on-board MICs
- USB-C port for USB 2.0 OTG
- On-board FTDI USB2SERIAL port for Linux console
Audio, Display and USB support will be added later when support of the
corresponding power domains will be added, for now they are kept disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[khilman: fix minor typo regultor -> regulator]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
First rename the sysctl control to abi.tagged_addr_disabled and make it
default off (zero). When abi.tagged_addr_disabled == 1, only block the
enabling of the TBI ABI via prctl(PR_SET_TAGGED_ADDR_CTRL, PR_TAGGED_ADDR_ENABLE).
Getting the status of the ABI or disabling it is still allowed.
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
In perf_event.c we use smp_processor_id(), but we haven't included
<linux/smp.h> where it is defined, and rely on this being pulled in
via a transitive include. Let's make this more robust by including
<linux.smp.h> explicitly.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Raphael Gault <raphael.gault@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Add dynamic power coefficients for the Silver and Gold CPU cores of
the Qualcomm SDM845.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This is a preparatory patch for kexec_file_load() lockdown. A locked down
kernel needs to prevent unsigned kernel images from being loaded with
kexec_file_load(). Currently, the only way to force the signature
verification is compiling with KEXEC_VERIFY_SIG. This prevents loading
usigned images even when the kernel is not locked down at runtime.
This patch splits KEXEC_VERIFY_SIG into KEXEC_SIG and KEXEC_SIG_FORCE.
Analogous to the MODULE_SIG and MODULE_SIG_FORCE for modules, KEXEC_SIG
turns on the signature verification but allows unsigned images to be
loaded. KEXEC_SIG_FORCE disallows images without a valid signature.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matthew Garrett <mjg59@google.com>
cc: kexec@lists.infradead.org
Signed-off-by: James Morris <jmorris@namei.org>
Update the reserved-memory map to version 3, to adjust to changes in the
remoteprocs.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
According to rock64 schemetic V2 and V3, the VCC_HOST_5V output is
controlled by USB_20_HOST_DRV, which is the same as VCC_HOST1_5V.
V1 hardware was never sold and only V2/V3 is with customers,
so there is no need to keep a seaprate v1 version around.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This includes DSP reserved memory, ADMA DSP device and DSP MU
communication channels description.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add A53 OPP table, cpu regulator and speed grading node to
support cpu-freq driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MN DDR4 EVK board, there is a rohm,bd71847 PMIC
on i2c1 bus, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Nano Media Applications Processor is a new SoC of the i.MX8M
family, it is a 14nm FinFET product of the growing mScale family targeting
the consumer market. It is built in Samsung 14LPP to achieve both high
performance and low power consumption and relies on a powerful fully
coherent core complex based on a quad core ARM Cortex-A53 cluster,
Cortex-M7 low-power coprocessor and graphics accelerator.
This patch adds the basic dtsi support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1028A has a clock domain PXLCLK0 used for the Display output
interface in the display core, independent of the system bus frequency,
for flexible clock design. This display core has its own pixel clock.
This patch enable the pixel clock provider on the LS1028A.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lx2160a platform, the i2c input clock is actually platform pll CLK / 16
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1028a platform, the i2c input clock is actually platform pll CLK / 4
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1012a platform, the i2c input clock is actually platform pll CLK / 4
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1088a platform, the i2c input clock is actually platform pll CLK / 8
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the nodes to include little-endian
property to be consistent with the hardware.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Thermal Monitoring Unit (TMU) monitors and reports the
temperature from 2 remote temperature measurement sites
located on ls1028a chip.
Add TMU dts node to enable this feature.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of Feb
12, 2019, the base address of the IPMMU-VC0 block on R-Car V3H is
0xfe990000.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
* According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal delay mode isn't supported
on R-Car E3 (r8a77990) and D3 (r8a77995).
* TX clock internal delay mode is required for reliable 1Gbps communication
using the KSZ9031RNX phy present on the Ebisu and Draak boards.
Thus, the E3 based Ebisu and D3 based Draak boards can not reliably
use 1Gbps and the speed should be limited to 100Mbps.
Based on work by Kazuya Mizuguchi.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds support for HDMI audio to the device tree
common to the HiHope RZ/G2M and the HiHope RZ/G2N.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
For VPIPT I-caches, we need I-cache maintenance on VMID rollover to
avoid an ABA problem. Consider a single vCPU VM, with a pinned stage-2,
running with an idmap VA->IPA and idmap IPA->PA. If we don't do
maintenance on rollover:
// VMID A
Writes insn X to PA 0xF
Invalidates PA 0xF (for VMID A)
I$ contains [{A,F}->X]
[VMID ROLLOVER]
// VMID B
Writes insn Y to PA 0xF
Invalidates PA 0xF (for VMID B)
I$ contains [{A,F}->X, {B,F}->Y]
[VMID ROLLOVER]
// VMID A
I$ contains [{A,F}->X, {B,F}->Y]
Unexpectedly hits stale I$ line {A,F}->X.
However, for PIPT and VIPT I-caches, the VMID doesn't affect lookup or
constrain maintenance. Given the VMID doesn't affect PIPT and VIPT
I-caches, and given VMID rollover is independent of changes to stage-2
mappings, I-cache maintenance cannot be necessary on VMID rollover for
PIPT or VIPT I-caches.
This patch removes the maintenance on rollover for VIPT and PIPT
I-caches. At the same time, the unnecessary colons are removed from the
asm statement to make it more legible.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Marc Zyngier <maz@kernel.org>
'7d0c76bdf227 ("clk: qcom: Add WCSS gcc clock control for QCS404")'
introduces two new clocks to gcc. These are not used before
clk_disable_unused() and as such the clock framework tries to disable
them.
But on the EVB these registers are only accessible through TrustZone, so
these clocks must be marked as "protected" to prevent the clock code
from touching them.
Numerical values are used as the constants are not yet available in a
common tree.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
- Don't taint the kernel if CPUs have different sets of page sizes
supported (other than the one in use).
- Issue I-cache maintenance for module ftrace trampoline.
-----BEGIN PGP SIGNATURE-----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=VneQ
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Don't taint the kernel if CPUs have different sets of page sizes
supported (other than the one in use).
- Issue I-cache maintenance for module ftrace trampoline.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ftrace: Ensure module ftrace trampoline is coherent with I-side
arm64: cpufeature: Don't treat granule sizes as strict
The initial support for dynamic ftrace trampolines in modules made use
of an indirect branch which loaded its target from the beginning of
a special section (e71a4e1beb ("arm64: ftrace: add support for far
branches to dynamic ftrace")). Since no instructions were being patched,
no cache maintenance was needed. However, later in be0f272bfc ("arm64:
ftrace: emit ftrace-mod.o contents through code") this code was reworked
to output the trampoline instructions directly into the PLT entry but,
unfortunately, the necessary cache maintenance was overlooked.
Add a call to __flush_icache_range() after writing the new trampoline
instructions but before patching in the branch to the trampoline.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: James Morse <james.morse@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: be0f272bfc ("arm64: ftrace: emit ftrace-mod.o contents through code")
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
P710 is a RK3399 based SBC, designed by Leez [0].
Specification
- Rockchip RK3399
- 4/2GB LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply
[0]https://leez.lenovo.com
Signed-off-by: Andy Yan <andyshrk@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rockpro64 contains a nor-flash chip connected to spi1.
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
[a number of cleanups]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the ACPI_APEI_PCIEAER configuration to support PCIe AER error report
for the Hisilicon D06 board and the dependencies PCIEAER and ACPI_APEI have
been enabled in the default config.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
- a few small DT fixes for g12a/g12b platforms
-----BEGIN PGP SIGNATURE-----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=bMaE
-----END PGP SIGNATURE-----
Merge tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixes
arm64: dts: Amlogic fixes for v5.3-rc
- a few small DT fixes for g12a/g12b platforms
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: amlogic: odroid-n2: keep SD card regulator always on
arm64: dts: meson-g12a-sei510: enable IR controller
arm64: dts: meson-g12a: add missing dwc2 phy-names
Neil Armstrong