The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ
during suspend-to-idle transitions and, consequently, any events
signaled through it wake up the system from that state. However,
on some systems some of the events signaled via the ACPI SCI while
suspended to idle should not cause the system to wake up. In fact,
quite often they should just be discarded.
Arguably, systems should not resume entirely on such events, but in
order to decide which events really should cause the system to resume
and which are spurious, it is necessary to resume up to the point
when ACPI SCIs are actually handled and processed, which is after
executing dpm_resume_noirq() in the system resume path.
For this reasons, add a loop around freeze_enter() in which the
platforms can process events signaled via multiplexed IRQ lines
like the ACPI SCI and add suspend-to-idle hooks that can be
used for this purpose to struct platform_freeze_ops.
In the ACPI case, the ->wake hook is used for checking if the SCI
has triggered while suspended and deferring the interrupt-induced
system wakeup until the events signaled through it are actually
processed sufficiently to decide whether or not the system should
resume. In turn, the ->sync hook allows all of the relevant event
queues to be flushed so as to prevent events from being missed due
to race conditions.
In addition to that, some ACPI code processing wakeup events needs
to be modified to use the "hard" version of wakeup triggers, so that
it will cause a system resume to happen on device-induced wakeup
events even if the "soft" mechanism to prevent the system from
suspending is not enabled. However, to preserve the existing
behavior with respect to suspend-to-RAM, this only is done in
the suspend-to-idle case and only if an SCI has occurred while
suspended.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull CPU hotplug fix from Ingo Molnar:
"An error handling corner case fix"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Drop the device lock on error
Pull RCU fixes from Ingo Molnar:
"Fix an SRCU bug affecting KVM IRQ injection"
* 'rcu-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
srcu: Allow use of Classic SRCU from both process and interrupt context
srcu: Allow use of Tiny/Tree SRCU from both process and interrupt context
Pull perf fixes from Ingo Molnar:
"This is mostly tooling fixes, plus an instruction pointer filtering
fix.
It's more fixes than usual - Arnaldo got back from a longer vacation
and there was a backlog"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
perf symbols: Kill dso__build_id_is_kmod()
perf symbols: Keep DSO->symtab_type after decompress
perf tests: Decompress kernel module before objdump
perf tools: Consolidate error path in __open_dso()
perf tools: Decompress kernel module when reading DSO data
perf annotate: Use dso__decompress_kmodule_path()
perf tools: Introduce dso__decompress_kmodule_{fd,path}
perf tools: Fix a memory leak in __open_dso()
perf annotate: Fix symbolic link of build-id cache
perf/core: Drop kernel samples even though :u is specified
perf script python: Remove dups in documentation examples
perf script python: Updated trace_unhandled() signature
perf script python: Fix wrong code snippets in documentation
perf script: Fix documentation errors
perf script: Fix outdated comment for perf-trace-python
perf probe: Fix examples section of documentation
perf report: Ensure the perf DSO mapping matches what libdw sees
perf report: Include partial stacks unwound with libdw
perf annotate: Add missing powerpc triplet
perf test: Disable breakpoint signal tests for powerpc
...
Pull RCU fix from Paul E. McKenney:
" This series enables srcu_read_lock() and srcu_read_unlock() to be used from
interrupt handlers, which fixes a bug in KVM's use of SRCU in delivery
of interrupts to guest OSes. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Revert a recent commit that attempted to avoid spurious wakeups
from suspend-to-idle via ACPI SCI, but introduced regressions on
some systems (Rafael Wysocki).
We will get back to the problem it tried to address in the next
cycle.
- Fix a possible division by 0 during intel_pstate initialization
due to a missing check (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=oWdX
-----END PGP SIGNATURE-----
Merge tag 'pm-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These revert one problematic commit related to system sleep and fix
one recent intel_pstate regression.
Specifics:
- Revert a recent commit that attempted to avoid spurious wakeups
from suspend-to-idle via ACPI SCI, but introduced regressions on
some systems (Rafael Wysocki).
We will get back to the problem it tried to address in the next
cycle.
- Fix a possible division by 0 during intel_pstate initialization
due to a missing check (Rafael Wysocki)"
* tag 'pm-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / sleep: Ignore spurious SCI wakeups from suspend-to-idle"
cpufreq: intel_pstate: Avoid division by 0 in min_perf_pct_min()
Pull printk fix from Petr Mladek:
"This reverts a fix added into 4.12-rc1. It caused the kernel log to be
printed on another console when two consoles of the same type were
defined, e.g. console=ttyS0 console=ttyS1.
This configuration was never supported by kernel itself, but it
started to make sense with systemd. In other words, the commit broke
userspace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
Revert "printk: fix double printing with earlycon"
Linu Cherian reported a WARN in cleanup_srcu_struct() when shutting
down a guest running iperf on a VFIO assigned device. This happens
because irqfd_wakeup() calls srcu_read_lock(&kvm->irq_srcu) in interrupt
context, while a worker thread does the same inside kvm_set_irq(). If the
interrupt happens while the worker thread is executing __srcu_read_lock(),
updates to the Classic SRCU ->lock_count[] field or the Tree SRCU
->srcu_lock_count[] field can be lost.
The docs say you are not supposed to call srcu_read_lock() and
srcu_read_unlock() from irq context, but KVM interrupt injection happens
from (host) interrupt context and it would be nice if SRCU supported the
use case. KVM is using SRCU here not really for the "sleepable" part,
but rather due to its IPI-free fast detection of grace periods. It is
therefore not desirable to switch back to RCU, which would effectively
revert commit 719d93cd5f ("kvm/irqchip: Speed up KVM_SET_GSI_ROUTING",
2014-01-16).
However, the docs are overly conservative. You can have an SRCU instance
only has users in irq context, and you can mix process and irq context
as long as process context users disable interrupts. In addition,
__srcu_read_unlock() actually uses this_cpu_dec() on both Tree SRCU and
Classic SRCU. For those two implementations, only srcu_read_lock()
is unsafe.
When Classic SRCU's __srcu_read_unlock() was changed to use this_cpu_dec(),
in commit 5a41344a3d ("srcu: Simplify __srcu_read_unlock() via
this_cpu_dec()", 2012-11-29), __srcu_read_lock() did two increments.
Therefore it kept __this_cpu_inc(), with preempt_disable/enable in
the caller. Tree SRCU however only does one increment, so on most
architectures it is more efficient for __srcu_read_lock() to use
this_cpu_inc(), and any performance differences appear to be down in
the noise.
Cc: stable@vger.kernel.org
Fixes: 719d93cd5f ("kvm/irqchip: Speed up KVM_SET_GSI_ROUTING")
Reported-by: Linu Cherian <linuc.decode@gmail.com>
Suggested-by: Linu Cherian <linuc.decode@gmail.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Linu Cherian reported a WARN in cleanup_srcu_struct() when shutting
down a guest running iperf on a VFIO assigned device. This happens
because irqfd_wakeup() calls srcu_read_lock(&kvm->irq_srcu) in interrupt
context, while a worker thread does the same inside kvm_set_irq(). If the
interrupt happens while the worker thread is executing __srcu_read_lock(),
updates to the Classic SRCU ->lock_count[] field or the Tree SRCU
->srcu_lock_count[] field can be lost.
The docs say you are not supposed to call srcu_read_lock() and
srcu_read_unlock() from irq context, but KVM interrupt injection happens
from (host) interrupt context and it would be nice if SRCU supported the
use case. KVM is using SRCU here not really for the "sleepable" part,
but rather due to its IPI-free fast detection of grace periods. It is
therefore not desirable to switch back to RCU, which would effectively
revert commit 719d93cd5f ("kvm/irqchip: Speed up KVM_SET_GSI_ROUTING",
2014-01-16).
However, the docs are overly conservative. You can have an SRCU instance
only has users in irq context, and you can mix process and irq context
as long as process context users disable interrupts. In addition,
__srcu_read_unlock() actually uses this_cpu_dec() on both Tree SRCU and
Classic SRCU. For those two implementations, only srcu_read_lock()
is unsafe.
When Classic SRCU's __srcu_read_unlock() was changed to use this_cpu_dec(),
in commit 5a41344a3d ("srcu: Simplify __srcu_read_unlock() via
this_cpu_dec()", 2012-11-29), __srcu_read_lock() did two increments.
Therefore it kept __this_cpu_inc(), with preempt_disable/enable in
the caller. Tree SRCU however only does one increment, so on most
architectures it is more efficient for __srcu_read_lock() to use
this_cpu_inc(), and any performance differences appear to be down in
the noise.
Unlike Classic and Tree SRCU, Tiny SRCU does increments and decrements on
a single variable. Therefore, as Peter Zijlstra pointed out, Tiny SRCU's
implementation already supports mixed-context use of srcu_read_lock()
and srcu_read_unlock(), at least as long as uses of srcu_read_lock()
and srcu_read_unlock() in each handler are nested and paired properly.
In other words, it is still illegal to (say) invoke srcu_read_lock()
in an interrupt handler and to invoke the matching srcu_read_unlock()
in a softirq handler. Therefore, the only change required for Tiny SRCU
is to its comments.
Fixes: 719d93cd5f ("kvm/irqchip: Speed up KVM_SET_GSI_ROUTING")
Reported-by: Linu Cherian <linuc.decode@gmail.com>
Suggested-by: Linu Cherian <linuc.decode@gmail.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit cf39bf58af.
The commit regression to users that define both console=ttyS1
and console=ttyS0 on the command line, see
https://lkml.kernel.org/r/20170509082915.GA13236@bistromath.localdomain
The kernel log messages always appeared only on one serial port. It is
even documented in Documentation/admin-guide/serial-console.rst:
"Note that you can only define one console per device type (serial,
video)."
The above mentioned commit changed the order in which the command line
parameters are searched. As a result, the kernel log messages go to
the last mentioned ttyS* instead of the first one.
We long thought that using two console=ttyS* on the command line
did not make sense. But then we realized that console= parameters
were handled also by systemd, see
http://0pointer.de/blog/projects/serial-console.html
"By default systemd will instantiate one serial-getty@.service on
the main kernel console, if it is not a virtual terminal."
where
"[4] If multiple kernel consoles are used simultaneously, the main
console is the one listed first in /sys/class/tty/console/active,
which is the last one listed on the kernel command line."
This puts the original report into another light. The system is running
in qemu. The first serial port is used to store the messages into a file.
The second one is used to login to the system via a socket. It depends
on systemd and the historic kernel behavior.
By other words, systemd causes that it makes sense to define both
console=ttyS1 console=ttyS0 on the command line. The kernel fix
caused regression related to userspace (systemd) and need to be
reverted.
In addition, it went out that the fix helped only partially.
The messages still were duplicated when the boot console was
removed early by late_initcall(printk_late_init). Then the entire
log was replayed when the same console was registered as a normal one.
Link: 20170606160339.GC7604@pathway.suse.cz
Cc: Aleksey Makarov <aleksey.makarov@linaro.org>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Robin Murphy <robin.murphy@arm.com>,
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Nair, Jayachandran" <Jayachandran.Nair@cavium.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Revert commit eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups
from suspend-to-idle) as it turned out to be premature and triggered
a number of different issues on various systems.
That includes, but is not limited to, premature suspend-to-RAM aborts
on Dell XPS 13 (9343) reported by Dominik.
The issue the commit in question attempted to address is real and
will need to be taken care of going forward, but evidently more work
is needed for this purpose.
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull cgroup fixes from Tejun Heo:
"Two cgroup fixes. One to address RCU delay of cpuset removal affecting
userland visible behaviors. The other fixes a race condition between
controller disable and cgroup removal"
* 'for-4.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: consider dying css as offline
cgroup: Prevent kill_css() from being called more than once
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If a custom CPU target is specified and that one is not available _or_
can't be interrupted then the code returns to userland without dropping a
lock as notices by lockdep:
|echo 133 > /sys/devices/system/cpu/cpu7/hotplug/target
| ================================================
| [ BUG: lock held when returning to user space! ]
| ------------------------------------------------
| bash/503 is leaving the kernel with locks still held!
| 1 lock held by bash/503:
| #0: (device_hotplug_lock){+.+...}, at: [<ffffffff815b5650>] lock_device_hotplug_sysfs+0x10/0x40
So release the lock then.
Fixes: 757c989b99 ("cpu/hotplug: Make target state writeable")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20170602142714.3ogo25f2wbq6fjpj@linutronix.de
Pull livepatching fix from Jiri Kosina:
"Kconfig dependency fix for livepatching infrastructure from Miroslav
Benes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: Make livepatch dependent on !TRIM_UNUSED_KSYMS
Pull timer fixlet from Thomas Gleixner:
"Silence dmesg spam by making the posix cpu timer printks depend on
print_fatal_signals"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-timers: Make signal printks conditional
Pull locking fix from Thomas Gleixner:
"A fix for a state leak which was introduced in the recent rework of
futex/rtmutex interaction"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex,rt_mutex: Fix rt_mutex_cleanup_proxy_lock()
Pull kthread fix from Thomas Gleixner:
"A single fix which prevents a use after free when kthread fork fails"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kthread: Fix use-after-free if kthread fork fails
One was simply a memory leak where not all was being freed that should
have been in releasing a file pointer on set_graph_function.
Then Thomas found that the ftrace trampolines were marked for read/write
as well as execute. To shrink the possible attack surface, he added
calls to set them to ro. Which also uncovered some other issues with
freeing module allocated memory that had its permissions changed.
Kprobes had a similar issue which is fixed and a selftest was added
to trigger that issue again.
-----BEGIN PGP SIGNATURE-----
iQExBAABCAAbBQJZKOiVFBxyb3N0ZWR0QGdvb2RtaXMub3JnAAoJEMm5BfJq2Y3L
vBoH/jxVozuAEVCv+Nbj6fhRxe4emjo0lZZb32EbEaSV/nUQGqHIZFdDQtbt+ld+
sn06/BSMBI+L4BqLj1BCAW0e/zIn/4birIg53SX5jQwc3AlhUG7HS2d+RJZZCrp9
Zofq9L6xZ4Hl2XjkPXqwEgtrwxQtkIPLlJqeYDJ6BVrlPfOPEwB7bfR7B684wiYT
6h2Qo7f/ZQzgJ1sK8N2IjHEnAgE08KCYcj4IB4WHJk6SqQz3bv1Y00WBg2UQihVT
TPPSVhYLnrSw53fxyALqZbHo2DvnQf1TnNadWxvSIpbvgm/T5GG60FDtvHgNfbwz
yKuKAog+P9xBLkoAcfvODLY9O5s=
=75TZ
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fixes from Steven Rostedt:
"There's been a few memory issues found with ftrace.
One was simply a memory leak where not all was being freed that should
have been in releasing a file pointer on set_graph_function.
Then Thomas found that the ftrace trampolines were marked for
read/write as well as execute. To shrink the possible attack surface,
he added calls to set them to ro. Which also uncovered some other
issues with freeing module allocated memory that had its permissions
changed.
Kprobes had a similar issue which is fixed and a selftest was added to
trigger that issue again"
* tag 'trace-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
x86/ftrace: Make sure that ftrace trampolines are not RWX
x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()
selftests/ftrace: Add a testcase for many kprobe events
kprobes/x86: Fix to set RWX bits correctly before releasing trampoline
ftrace: Fix memory leak in ftrace_graph_release()
Fix kprobes to set(recover) RWX bits correctly on trampoline
buffer before releasing it. Releasing readonly page to
module_memfree() crash the kernel.
Without this fix, if kprobes user register a bunch of kprobes
in function body (since kprobes on function entry usually
use ftrace) and unregister it, kernel hits a BUG and crash.
Link: http://lkml.kernel.org/r/149570868652.3518.14120169373590420503.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Fixes: d0381c81c2 ("kprobes/x86: Set kprobes pages read-only")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
If TRIM_UNUSED_KSYMS is enabled, all unneeded exported symbols are made
unexported. Two-pass build of the kernel is done to find out which
symbols are needed based on a configuration. This effectively
complicates things for out-of-tree modules.
Livepatch exports functions to (un)register and enable/disable a live
patch. The only in-tree module which uses these functions is a sample in
samples/livepatch/. If the sample is disabled, the functions are
trimmed and out-of-tree live patches cannot be built.
Note that live patches are intended to be built out-of-tree.
Suggested-by: Michal Marek <mmarek@suse.com>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Jessica Yu <jeyu@redhat.com>
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull networking fixes from David Miller:
1) Fix state pruning in bpf verifier wrt. alignment, from Daniel
Borkmann.
2) Handle non-linear SKBs properly in SCTP ICMP parsing, from Davide
Caratti.
3) Fix bit field definitions for rss_hash_type of descriptors in mlx5
driver, from Jesper Brouer.
4) Defer slave->link updates until bonding is ready to do a full commit
to the new settings, from Nithin Sujir.
5) Properly reference count ipv4 FIB metrics to avoid use after free
situations, from Eric Dumazet and several others including Cong Wang
and Julian Anastasov.
6) Fix races in llc_ui_bind(), from Lin Zhang.
7) Fix regression of ESP UDP encapsulation for TCP packets, from
Steffen Klassert.
8) Fix mdio-octeon driver Kconfig deps, from Randy Dunlap.
9) Fix regression in setting DSCP on ipv6/GRE encapsulation, from Peter
Dawson.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add reference counting to metrics
net: ethernet: ax88796: don't call free_irq without request_irq first
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
sctp: fix ICMP processing if skb is non-linear
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
bonding: Don't update slave->link until ready to commit
test_bpf: Add a couple of tests for BPF_JSGE.
bpf: add various verifier test cases
bpf: fix wrong exposure of map_flags into fdinfo for lpm
bpf: add bpf_clone_redirect to bpf_helper_changes_pkt_data
bpf: properly reset caller saved regs after helper call and ld_abs/ind
bpf: fix incorrect pruning decision when alignment must be tracked
arp: fixed -Wuninitialized compiler warning
tcp: avoid fastopen API to be used on AF_UNSPEC
net: move somaxconn init from sysctl code
net: fix potential null pointer dereference
geneve: fix fill_info when using collect_metadata
virtio-net: enable TSO/checksum offloads for Q-in-Q vlans
be2net: Fix offload features for Q-in-Q packets
vlan: Fix tcp checksum offloads in Q-in-Q vlans
...
trie_alloc() always needs to have BPF_F_NO_PREALLOC passed in via
attr->map_flags, since it does not support preallocation yet. We
check the flag, but we never copy the flag into trie->map.map_flags,
which is later on exposed into fdinfo and used by loaders such as
iproute2. Latter uses this in bpf_map_selfcheck_pinned() to test
whether a pinned map has the same spec as the one from the BPF obj
file and if not, bails out, which is currently the case for lpm
since it exposes always 0 as flags.
Also copy over flags in array_map_alloc() and stack_map_alloc().
They always have to be 0 right now, but we should make sure to not
miss to copy them over at a later point in time when we add actual
flags for them to use.
Fixes: b95a5c4db0 ("bpf: add a longest prefix match trie map implementation")
Reported-by: Jarno Rajahalme <jarno@covalent.io>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, after performing helper calls, we clear all caller saved
registers, that is r0 - r5 and fill r0 depending on struct bpf_func_proto
specification. The way we reset these regs can affect pruning decisions
in later paths, since we only reset register's imm to 0 and type to
NOT_INIT. However, we leave out clearing of other variables such as id,
min_value, max_value, etc, which can later on lead to pruning mismatches
due to stale data.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we enforce alignment tracking on direct packet access,
the verifier lets the following program pass despite doing a packet
write with unaligned access:
0: (61) r2 = *(u32 *)(r1 +76)
1: (61) r3 = *(u32 *)(r1 +80)
2: (61) r7 = *(u32 *)(r1 +8)
3: (bf) r0 = r2
4: (07) r0 += 14
5: (25) if r7 > 0x1 goto pc+4
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=0,max_value=1 R10=fp
6: (2d) if r0 > r3 goto pc+1
R0=pkt(id=0,off=14,r=14) R1=ctx R2=pkt(id=0,off=0,r=14)
R3=pkt_end R7=inv,min_value=0,max_value=1 R10=fp
7: (63) *(u32 *)(r0 -4) = r0
8: (b7) r0 = 0
9: (95) exit
from 6 to 8:
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=0,max_value=1 R10=fp
8: (b7) r0 = 0
9: (95) exit
from 5 to 10:
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=2 R10=fp
10: (07) r0 += 1
11: (05) goto pc-6
6: safe <----- here, wrongly found safe
processed 15 insns
However, if we enforce a pruning mismatch by adding state into r8
which is then being mismatched in states_equal(), we find that for
the otherwise same program, the verifier detects a misaligned packet
access when actually walking that path:
0: (61) r2 = *(u32 *)(r1 +76)
1: (61) r3 = *(u32 *)(r1 +80)
2: (61) r7 = *(u32 *)(r1 +8)
3: (b7) r8 = 1
4: (bf) r0 = r2
5: (07) r0 += 14
6: (25) if r7 > 0x1 goto pc+4
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=0,max_value=1
R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
7: (2d) if r0 > r3 goto pc+1
R0=pkt(id=0,off=14,r=14) R1=ctx R2=pkt(id=0,off=0,r=14)
R3=pkt_end R7=inv,min_value=0,max_value=1
R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
8: (63) *(u32 *)(r0 -4) = r0
9: (b7) r0 = 0
10: (95) exit
from 7 to 9:
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=0,max_value=1
R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
9: (b7) r0 = 0
10: (95) exit
from 6 to 11:
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=2
R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
11: (07) r0 += 1
12: (b7) r8 = 0
13: (05) goto pc-7 <----- mismatch due to r8
7: (2d) if r0 > r3 goto pc+1
R0=pkt(id=0,off=15,r=15) R1=ctx R2=pkt(id=0,off=0,r=15)
R3=pkt_end R7=inv,min_value=2
R8=imm0,min_value=0,max_value=0,min_align=2147483648 R10=fp
8: (63) *(u32 *)(r0 -4) = r0
misaligned packet access off 2+15+-4 size 4
The reason why we fail to see it in states_equal() is that the
third test in compare_ptrs_to_packet() ...
if (old->off <= cur->off &&
old->off >= old->range && cur->off >= cur->range)
return true;
... will let the above pass. The situation we run into is that
old->off <= cur->off (14 <= 15), meaning that prior walked paths
went with smaller offset, which was later used in the packet
access after successful packet range check and found to be safe
already.
For example: Given is R0=pkt(id=0,off=0,r=0). Adding offset 14
as in above program to it, results in R0=pkt(id=0,off=14,r=0)
before the packet range test. Now, testing this against R3=pkt_end
with 'if r0 > r3 goto out' will transform R0 into R0=pkt(id=0,off=14,r=14)
for the case when we're within bounds. A write into the packet
at offset *(u32 *)(r0 -4), that is, 2 + 14 -4, is valid and
aligned (2 is for NET_IP_ALIGN). After processing this with
all fall-through paths, we later on check paths from branches.
When the above skb->mark test is true, then we jump near the
end of the program, perform r0 += 1, and jump back to the
'if r0 > r3 goto out' test we've visited earlier already. This
time, R0 is of type R0=pkt(id=0,off=15,r=0), and we'll prune
that part because this time we'll have a larger safe packet
range, and we already found that with off=14 all further insn
were already safe, so it's safe as well with a larger off.
However, the problem is that the subsequent write into the packet
with 2 + 15 -4 is then unaligned, and not caught by the alignment
tracking. Note that min_align, aux_off, and aux_off_align were
all 0 in this example.
Since we cannot tell at this time what kind of packet access was
performed in the prior walk and what minimal requirements it has
(we might do so in the future, but that requires more complexity),
fix it to disable this pruning case for strict alignment for now,
and let the verifier do check such paths instead. With that applied,
the test cases pass and reject the program due to misalignment.
Fixes: d117441674 ("bpf: Track alignment of register values in the verifier.")
Reference: http://patchwork.ozlabs.org/patch/761909/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In most cases, a cgroup controller don't care about the liftimes of
cgroups. For the controller, a css becomes online when ->css_online()
is called on it and offline when ->css_offline() is called.
However, cpuset is special in that the user interface it exposes cares
whether certain cgroups exist or not. Combined with the RCU delay
between cgroup removal and css offlining, this can lead to user
visible behavior oddities where operations which should succeed after
cgroup removals fail for some time period. The effects of cgroup
removals are delayed when seen from userland.
This patch adds css_is_dying() which tests whether offline is pending
and updates is_cpuset_online() so that the function returns false also
while offline is pending. This gets rid of the userland visible
delays.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Link: http://lkml.kernel.org/r/327ca1f5-7957-fbb9-9e5f-9ba149d40ba2@oracle.com
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull ptrace fix from Eric Biederman:
"This fixes a brown paper bag bug. When I fixed the ptrace interaction
with user namespaces I added a new field ptracer_cred in struct_task
and I failed to properly initialize it on fork.
This dangling pointer wound up breaking runing setuid applications run
from the enlightenment window manager.
As this is the worst sort of bug. A regression breaking user space for
no good reason let's get this fixed"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ptrace: Properly initialize ptracer_cred on fork
A recent commit added extra printks for CPU/RT limits. This can result in
excessive spam in dmesg.
Make the printks conditional on print_fatal_signals.
Fixes: e7ea7c9806 ("rlimits: Print more information when CPU/RT limits are exceeded")
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Arun Raghavan <arun@arunraghavan.net>
When I introduced ptracer_cred I failed to consider the weirdness of
fork where the task_struct copies the old value by default. This
winds up leaving ptracer_cred set even when a process forks and
the child process does not wind up being ptraced.
Because ptracer_cred is not set on non-ptraced processes whose
parents were ptraced this has broken the ability of the enlightenment
window manager to start setuid children.
Fix this by properly initializing ptracer_cred in ptrace_init_task
This must be done with a little bit of care to preserve the current value
of ptracer_cred when ptrace carries through fork. Re-reading the
ptracer_cred from the ptracing process at this point is inconsistent
with how PT_PTRACE_CAP has been maintained all of these years.
Tested-by: Takashi Iwai <tiwai@suse.de>
Fixes: 64b875f7ac ("ptrace: Capture the ptracer's creds not PT_PTRACE_CAP")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
- Fix RTC wakeup from suspend-to-idle broken by the recent rework
of ACPI wakeup handling (Rafael Wysocki).
- Update intel_pstate driver documentation to reflect the current
code and explain how it works in more detail (Rafael Wysocki).
- Fix an issue related to CPU idleness detection on systems with
shared cpufreq policies in the schedutil governor (Juri Lelli).
- Fix a possible build issue in the dbx500 cpufreq driver (Arnd
Bergmann).
- Fix a function in the power capping framework core to return
an error code instead of 0 when there's an error (Dan Carpenter).
- Clean up variable definition in the hibernation core (Pushkar
Jambhlekar).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=2sNW
-----END PGP SIGNATURE-----
Merge tag 'pm-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix RTC wakeup from suspend-to-idle broken recently, fix CPU
idleness detection condition in the schedutil cpufreq governor, fix a
cpufreq driver build failure, fix an error code path in the power
capping framework, clean up the hibernate core and update the
intel_pstate documentation.
Specifics:
- Fix RTC wakeup from suspend-to-idle broken by the recent rework of
ACPI wakeup handling (Rafael Wysocki).
- Update intel_pstate driver documentation to reflect the current
code and explain how it works in more detail (Rafael Wysocki).
- Fix an issue related to CPU idleness detection on systems with
shared cpufreq policies in the schedutil governor (Juri Lelli).
- Fix a possible build issue in the dbx500 cpufreq driver (Arnd
Bergmann).
- Fix a function in the power capping framework core to return an
error code instead of 0 when there's an error (Dan Carpenter).
- Clean up variable definition in the hibernation core (Pushkar
Jambhlekar)"
* tag 'pm-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: dbx500: add a Kconfig symbol
PM / hibernate: Declare variables as static
PowerCap: Fix an error code in powercap_register_zone()
RTC: rtc-cmos: Fix wakeup from suspend-to-idle
PM / wakeup: Fix up wakeup_source_report_event()
cpufreq: intel_pstate: Document the current behavior and user interface
cpufreq: schedutil: use now as reference when aggregating shared policy requests
If a kthread forks (e.g. usermodehelper since commit 1da5c46fa9) but
fails in copy_process() between calling dup_task_struct() and setting
p->set_child_tid, then the value of p->set_child_tid will be inherited
from the parent and get prematurely freed by free_kthread_struct().
kthread()
- worker_thread()
- process_one_work()
| - call_usermodehelper_exec_work()
| - kernel_thread()
| - _do_fork()
| - copy_process()
| - dup_task_struct()
| - arch_dup_task_struct()
| - tsk->set_child_tid = current->set_child_tid // implied
| - ...
| - goto bad_fork_*
| - ...
| - free_task(tsk)
| - free_kthread_struct(tsk)
| - kfree(tsk->set_child_tid)
- ...
- schedule()
- __schedule()
- wq_worker_sleeping()
- kthread_data(task)->flags // UAF
The problem started showing up with commit 1da5c46fa9 since it reused
->set_child_tid for the kthread worker data.
A better long-term solution might be to get rid of the ->set_child_tid
abuse. The comment in set_kthread_struct() also looks slightly wrong.
Debugged-by: Jamie Iles <jamie.iles@oracle.com>
Fixes: 1da5c46fa9 ("kthread: Make struct kthread kmalloc'ed")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jamie Iles <jamie.iles@oracle.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20170509073959.17858-1-vegard.nossum@oracle.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Markus reported that the glibc/nptl/tst-robustpi8 test was failing after
commit:
cfafcd117d ("futex: Rework futex_lock_pi() to use rt_mutex_*_proxy_lock()")
The following trace shows the problem:
ld-linux-x86-64-2161 [019] .... 410.760971: SyS_futex: 00007ffbeb76b028: 80000875 op=FUTEX_LOCK_PI
ld-linux-x86-64-2161 [019] ...1 410.760972: lock_pi_update_atomic: 00007ffbeb76b028: curval=80000875 uval=80000875 newval=80000875 ret=0
ld-linux-x86-64-2165 [011] .... 410.760978: SyS_futex: 00007ffbeb76b028: 80000875 op=FUTEX_UNLOCK_PI
ld-linux-x86-64-2165 [011] d..1 410.760979: do_futex: 00007ffbeb76b028: curval=80000875 uval=80000875 newval=80000871 ret=0
ld-linux-x86-64-2165 [011] .... 410.760980: SyS_futex: 00007ffbeb76b028: 80000871 ret=0000
ld-linux-x86-64-2161 [019] .... 410.760980: SyS_futex: 00007ffbeb76b028: 80000871 ret=ETIMEDOUT
Task 2165 does an UNLOCK_PI, assigning the lock to the waiter task 2161
which then returns with -ETIMEDOUT. That wrecks the lock state, because now
the owner isn't aware it acquired the lock and removes the pending robust
list entry.
If 2161 is killed, the robust list will not clear out this futex and the
subsequent acquire on this futex will then (correctly) result in -ESRCH
which is unexpected by glibc, triggers an internal assertion and dies.
Task 2161 Task 2165
rt_mutex_wait_proxy_lock()
timeout();
/* T2161 is still queued in the waiter list */
return -ETIMEDOUT;
futex_unlock_pi()
spin_lock(hb->lock);
rtmutex_unlock()
remove_rtmutex_waiter(T2161);
mark_lock_available();
/* Make the next waiter owner of the user space side */
futex_uval = 2161;
spin_unlock(hb->lock);
spin_lock(hb->lock);
rt_mutex_cleanup_proxy_lock()
if (rtmutex_owner() !== current)
...
return FAIL;
....
return -ETIMEOUT;
This means that rt_mutex_cleanup_proxy_lock() needs to call
try_to_take_rt_mutex() so it can take over the rtmutex correctly which was
assigned by the waker. If the rtmutex is owned by some other task then this
call is harmless and just confirmes that the waiter is not able to acquire
it.
While there, fix what looks like a merge error which resulted in
rt_mutex_cleanup_proxy_lock() having two calls to
fixup_rt_mutex_waiters() and rt_mutex_wait_proxy_lock() not having any.
Both should have one, since both potentially touch the waiter list.
Fixes: 38d589f2fd ("futex,rt_mutex: Restructure rt_mutex_finish_proxy_lock()")
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Bug-Spotted-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Link: http://lkml.kernel.org/r/20170519154850.mlomgdsd26drq5j6@hirez.programming.kicks-ass.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull networking fixes from David Miller:
"Mostly netfilter bug fixes in here, but we have some bits elsewhere as
well.
1) Don't do SNAT replies for non-NATed connections in IPVS, from
Julian Anastasov.
2) Don't delete conntrack helpers while they are still in use, from
Liping Zhang.
3) Fix zero padding in xtables's xt_data_to_user(), from Willem de
Bruijn.
4) Add proper RCU protection to nf_tables_dump_set() because we
cannot guarantee that we hold the NFNL_SUBSYS_NFTABLES lock. From
Liping Zhang.
5) Initialize rcv_mss in tcp_disconnect(), from Wei Wang.
6) smsc95xx devices can't handle IPV6 checksums fully, so don't
advertise support for offloading them. From Nisar Sayed.
7) Fix out-of-bounds access in __ip6_append_data(), from Eric
Dumazet.
8) Make atl2_probe() propagate the error code properly on failures,
from Alexey Khoroshilov.
9) arp_target[] in bond_check_params() is used uninitialized. This
got changes from a global static to a local variable, which is how
this mistake happened. Fix from Jarod Wilson.
10) Fix fallout from unnecessary NULL check removal in cls_matchall,
from Jiri Pirko. This is definitely brown paper bag territory..."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
net: sched: cls_matchall: fix null pointer dereference
vsock: use new wait API for vsock_stream_sendmsg()
bonding: fix randomly populated arp target array
net: Make IP alignment calulations clearer.
bonding: fix accounting of active ports in 3ad
net: atheros: atl2: don't return zero on failure path in atl2_probe()
ipv6: fix out of bound writes in __ip6_append_data()
bridge: start hello_timer when enabling KERNEL_STP in br_stp_start
smsc95xx: Support only IPv4 TCP/UDP csum offload
arp: always override existing neigh entries with gratuitous ARP
arp: postpone addr_type calculation to as late as possible
arp: decompose is_garp logic into a separate function
arp: fixed error in a comment
tcp: initialize rcv_mss to TCP_MIN_MSS instead of 0
netfilter: xtables: fix build failure from COMPAT_XT_ALIGN outside CONFIG_COMPAT
ebtables: arpreply: Add the standard target sanity check
netfilter: nf_tables: revisit chain/object refcounting from elements
netfilter: nf_tables: missing sanitization in data from userspace
netfilter: nf_tables: can't assume lock is acquired when dumping set elems
netfilter: synproxy: fix conntrackd interaction
...
* intel_pstate:
cpufreq: intel_pstate: Document the current behavior and user interface
* pm-cpufreq:
cpufreq: dbx500: add a Kconfig symbol
* pm-cpufreq-sched:
cpufreq: schedutil: use now as reference when aggregating shared policy requests
The assignmnet:
ip_align = strict ? 2 : NET_IP_ALIGN;
in compare_pkt_ptr_alignment() trips up Coverity because we can only
get to this code when strict is true, therefore ip_align will always
be 2 regardless of NET_IP_ALIGN's value.
So just assign directly to '2' and explain the situation in the
comment above.
Reported-by: "Gustavo A. R. Silva" <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scheduler fix from Thomas Gleixner:
"A single scheduler fix:
Prevent idle task from ever being preempted. That makes sure that
synchronize_rcu_tasks() which is ignoring idle task does not pretend
that no task is stuck in preempted state. If that happens and idle was
preempted on a ftrace trampoline the machine crashes due to
inconsistent state"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Call __schedule() from do_idle() without enabling preemption
Pull irq fixes from Thomas Gleixner:
"A set of small fixes for the irq subsystem:
- Cure a data ordering problem with chained interrupts
- Three small fixlets for the mbigen irq chip"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix chained interrupt data ordering
irqchip/mbigen: Fix the clear register offset calculation
irqchip/mbigen: Fix potential NULL dereferencing
irqchip/mbigen: Fix memory mapping code
when deleting an instance. It also creates a selftest that triggers that bug.
Fix the delayed optimization happening after kprobes boot up self tests
being removed by freeing of init memory.
Comment kprobes on why the delay optimization is not a problem for removal
of modules, to keep other developers from searching that riddle.
Fix another rcu isn't watching in stack trace tracing.
Naveen N. Rao (4):
ftrace: Simplify glob handling in unregister_ftrace_function_probe_func()
ftrace/instances: Clear function triggers when removing instances
selftests/ftrace: Fix bashisms
selftests/ftrace: Add test to remove instance with active event triggers
Steven Rostedt (1):
tracing: Move postpone selftests to core from early_initcall
Steven Rostedt (VMware) (3):
ftrace: Remove #ifdef from code and add clear_ftrace_function_probes() stub
kprobes: Document how optimized kprobes are removed from module unload
tracing: Make sure RCU is watching before calling a stack trace
Thomas Gleixner (1):
tracing/kprobes: Enforce kprobes teardown after testing
-----BEGIN PGP SIGNATURE-----
iQExBAABCAAbBQJZIQapFBxyb3N0ZWR0QGdvb2RtaXMub3JnAAoJEMm5BfJq2Y3L
A6MIAKFLb6mQ4flRBXpWd2tD2B4DQpQ0H7SovseZnlH6Q7grU6POY/qbNl9xXiBA
3NavxqbIYokH8cxEqGAusL7ASUFPXJj6erMM1uc1WRuAzMpIjvgNacOtW5R+c5S9
ofR1xtKlBo/854J/IP6M3J0WqrK+B7TsS1WYKohe/tFMBpolbnFloHVfMMZlaL58
CQhCoAhkjJRsta6dJhbo+HoQy03VGyWsfFHtutBpIwsf81Naq4Stpxp7jdZLWhB8
Di5QdOji9lDayK6Uk7DDZqHxbjC9z6cCS9nVWIGHkE4AMpR3peYtsyCaAOBjVMLV
2OuhuREfZgKaYVMjUfdeYCayDAY=
=1gek
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix a bug caused by not cleaning up the new instance unique triggers
when deleting an instance. It also creates a selftest that triggers
that bug.
- Fix the delayed optimization happening after kprobes boot up self
tests being removed by freeing of init memory.
- Comment kprobes on why the delay optimization is not a problem for
removal of modules, to keep other developers from searching that
riddle.
- Fix another case of rcu not watching in stack trace tracing.
* tag 'trace-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Make sure RCU is watching before calling a stack trace
kprobes: Document how optimized kprobes are removed from module unload
selftests/ftrace: Add test to remove instance with active event triggers
selftests/ftrace: Fix bashisms
ftrace: Remove #ifdef from code and add clear_ftrace_function_probes() stub
ftrace/instances: Clear function triggers when removing instances
ftrace: Simplify glob handling in unregister_ftrace_function_probe_func()
tracing/kprobes: Enforce kprobes teardown after testing
tracing: Move postpone selftests to core from early_initcall
Pull block fixes from Jens Axboe:
"A small collection of fixes that should go into this cycle.
- a pull request from Christoph for NVMe, which ended up being
manually applied to avoid pulling in newer bits in master. Mostly
fibre channel fixes from James, but also a few fixes from Jon and
Vijay
- a pull request from Konrad, with just a single fix for xen-blkback
from Gustavo.
- a fuseblk bdi fix from Jan, fixing a regression in this series with
the dynamic backing devices.
- a blktrace fix from Shaohua, replacing sscanf() with kstrtoull().
- a request leak fix for drbd from Lars, fixing a regression in the
last series with the kref changes. This will go to stable as well"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvmet: release the sq ref on rdma read errors
nvmet-fc: remove target cpu scheduling flag
nvme-fc: stop queues on error detection
nvme-fc: require target or discovery role for fc-nvme targets
nvme-fc: correct port role bits
nvme: unmap CMB and remove sysfs file in reset path
blktrace: fix integer parse
fuseblk: Fix warning in super_setup_bdi_name()
block: xen-blkback: add null check to avoid null pointer dereference
drbd: fix request leak introduced by locking/atomic, kref: Kill kref_sub()
sscanf is a very poor way to parse integer. For example, I input
"discard" for act_mask, it gets 0xd and completely messes up. Using
correct API to do integer parse.
This patch also makes attributes accept any base of integer.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
As stack tracing now requires "rcu watching", force RCU to be watching when
recording a stack trace.
Link: http://lkml.kernel.org/r/20170512172449.879684501@goodmis.org
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Pull networking fixes from David Miller:
1) Don't allow negative TCP reordering values, from Soheil Hassas
Yeganeh.
2) Don't overflow while parsing ipv6 header options, from Craig Gallek.
3) Handle more cleanly the case where an individual route entry during
a dump will not fit into the allocated netlink SKB, from David
Ahern.
4) Add missing CONFIG_INET dependency for mlx5e, from Arnd Bergmann.
5) Allow neighbour updates to converge more quickly via gratuitous
ARPs, from Ihar Hrachyshka.
6) Fix compile error from CONFIG_INET is disabled, from Eric Dumazet.
7) Fix use after free in x25 protocol init, from Lin Zhang.
8) Valid VLAN pvid ranges passed into br_validate(), from Tobias
Jungel.
9) NULL out address lists in child sockets in SCTP, this is similar to
the fix we made for inet connection sockets last week. From Eric
Dumazet.
10) Fix NULL deref in mlxsw driver, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
mlxsw: spectrum: Avoid possible NULL pointer dereference
sh_eth: Do not print an error message for probe deferral
sh_eth: Use platform device for printing before register_netdev()
mlxsw: spectrum_router: Fix rif counter freeing routine
mlxsw: spectrum_dpipe: Fix incorrect entry index
cxgb4: update latest firmware version supported
qmi_wwan: add another Lenovo EM74xx device ID
sctp: do not inherit ipv6_{mc|ac|fl}_list from parent
udp: make *udp*_queue_rcv_skb() functions static
bridge: netlink: check vlan_default_pvid range
net: ethernet: faraday: To support device tree usage.
net: x25: fix one potential use-after-free issue
bpf: adjust verifier heuristics
ipv6: Check ip6_find_1stfragopt() return value properly.
selftests/bpf: fix broken build due to types.h
bnxt_en: Check status of firmware DCBX agent before setting DCB_CAP_DCBX_HOST.
bnxt_en: Call bnxt_dcb_init() after getting firmware DCBX configuration.
net: fix compile error in skb_orphan_partial()
ipv6: Prevent overrun when parsing v6 header options
neighbour: update neigh timestamps iff update is effective
...
Pull pid namespace fixes from Eric Biederman:
"These are two bugs that turn out to have simple fixes that were
reported during the merge window. Both of these issues have existed
for a while and it just happens that they both were reported at almost
the same time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
pid_ns: Fix race between setns'ed fork() and zap_pid_ns_processes()
pid_ns: Sleep in TASK_INTERRUPTIBLE in zap_pid_ns_processes
Current limits with regards to processing program paths do not
really reflect today's needs anymore due to programs becoming
more complex and verifier smarter, keeping track of more data
such as const ALU operations, alignment tracking, spilling of
PTR_TO_MAP_VALUE_ADJ registers, and other features allowing for
smarter matching of what LLVM generates.
This also comes with the side-effect that we result in fewer
opportunities to prune search states and thus often need to do
more work to prove safety than in the past due to different
register states and stack layout where we mismatch. Generally,
it's quite hard to determine what caused a sudden increase in
complexity, it could be caused by something as trivial as a
single branch somewhere at the beginning of the program where
LLVM assigned a stack slot that is marked differently throughout
other branches and thus causing a mismatch, where verifier
then needs to prove safety for the whole rest of the program.
Subsequently, programs with even less than half the insn size
limit can get rejected. We noticed that while some programs
load fine under pre 4.11, they get rejected due to hitting
limits on more recent kernels. We saw that in the vast majority
of cases (90+%) pruning failed due to register mismatches. In
case of stack mismatches, majority of cases failed due to
different stack slot types (invalid, spill, misc) rather than
differences in spilled registers.
This patch makes pruning more aggressive by also adding markers
that sit at conditional jumps as well. Currently, we only mark
jump targets for pruning. For example in direct packet access,
these are usually error paths where we bail out. We found that
adding these markers, it can reduce number of processed insns
by up to 30%. Another option is to ignore reg->id in probing
PTR_TO_MAP_VALUE_OR_NULL registers, which can help pruning
slightly as well by up to 7% observed complexity reduction as
stand-alone. Meaning, if a previous path with register type
PTR_TO_MAP_VALUE_OR_NULL for map X was found to be safe, then
in the current state a PTR_TO_MAP_VALUE_OR_NULL register for
the same map X must be safe as well. Last but not least the
patch also adds a scheduling point and bumps the current limit
for instructions to be processed to a more adequate value.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas discovered a bug where the kprobe trace tests had a race
condition where the kprobe_optimizer called from a delayed work queue
that does the optimizing and "unoptimizing" of a kprobe, can try to
modify the text after it has been freed by the init code.
The kprobe trace selftest is a special case, and Thomas and myself
investigated to see if there's a chance that this could also be a bug
with module unloading, as the code is not obvious to how it handles
this. After adding lots of printks, I figured it out. Thomas suggested
that this should be commented so that others will not have to go
through this exercise again.
Link: http://lkml.kernel.org/r/20170516145835.3827d3aa@gandalf.local.home
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Rafael J. Wysocki