SWP_FS is used to make swap_{read,write}page() go through the
filesystem, and it's only used for swap files over NFS. So, !SWP_FS
means non NFS for now, it could be either file backed or device backed.
Something similar goes with legacy SWP_FILE.
So in order to achieve the goal of the original patch, SWP_BLKDEV should
be used instead.
FS corruption can be observed with SSD device + XFS + fragmented
swapfile due to CONFIG_THP_SWAP=y.
I reproduced the issue with the following details:
Environment:
QEMU + upstream kernel + buildroot + NVMe (2 GB)
Kernel config:
CONFIG_BLK_DEV_NVME=y
CONFIG_THP_SWAP=y
Some reproducible steps:
mkfs.xfs -f /dev/nvme0n1
mkdir /tmp/mnt
mount /dev/nvme0n1 /tmp/mnt
bs="32k"
sz="1024m" # doesn't matter too much, I also tried 16m
xfs_io -f -c "pwrite -R -b $bs 0 $sz" -c "fdatasync" /tmp/mnt/sw
xfs_io -f -c "pwrite -R -b $bs 0 $sz" -c "fdatasync" /tmp/mnt/sw
xfs_io -f -c "pwrite -R -b $bs 0 $sz" -c "fdatasync" /tmp/mnt/sw
xfs_io -f -c "pwrite -F -S 0 -b $bs 0 $sz" -c "fdatasync" /tmp/mnt/sw
xfs_io -f -c "pwrite -R -b $bs 0 $sz" -c "fsync" /tmp/mnt/sw
mkswap /tmp/mnt/sw
swapon /tmp/mnt/sw
stress --vm 2 --vm-bytes 600M # doesn't matter too much as well
Symptoms:
- FS corruption (e.g. checksum failure)
- memory corruption at: 0xd2808010
- segfault
Fixes: f0eea189e8 ("mm, THP, swap: Don't allocate huge cluster for file backed swap device")
Fixes: 38d8b4e6bd ("mm, THP, swap: delay splitting THP during swap out")
Signed-off-by: Gao Xiang <hsiangkao@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Acked-by: Rafael Aquini <aquini@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Carlos Maiolino <cmaiolino@redhat.com>
Cc: Eric Sandeen <esandeen@redhat.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200820045323.7809-1-hsiangkao@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the commit 10befea91b ("mm: memcg/slab: use a single set of
kmem_caches for all allocations"), it becomes possible to call kfree()
from the slabs_destroy().
The functions cache_flusharray() and do_drain() calls slabs_destroy() on
array_cache of the local CPU without updating the size of the
array_cache. This enables the kfree() call from the slabs_destroy() to
recursively call cache_flusharray() which can potentially call
free_block() on the same elements of the array_cache of the local CPU
and causing double free and memory corruption.
To fix the issue, simply update the local CPU array_cache cache before
calling slabs_destroy().
Fixes: 10befea91b ("mm: memcg/slab: use a single set of kmem_caches for all allocations")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Roman Gushchin <guro@fb.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ted Ts'o <tytso@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
clang --target=<triple> is how we can specify a particular toolchain
triple to be use, fix the two occurences in the documentation.
Fixes: fcf1b6a35c ("Documentation/llvm: add documentation on building w/ Clang/LLVM")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
with a better API in 5.10 or 5.11, for now this is a fix
that works with existing userspace but keeps the current
ugly API.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl9ufLMUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMe9AgAgU3YQ2SktkqEOXjHMLqCH5Y3PKFI
S2anYpoKlH36Q6kzoqtkCj0GVagvdh5+Envz3I/tMdhv3Y/JgZaX1wHAe4cUl9BT
VyoiDBTWkhYRmpUbLYA8AtmgxQw1Hp8srH86rnvVGmLG6zdAa/rgUAKiQgT688Ej
CQvF5H7Zi3viPo2rInNSkgTIgewduqSWkwJ6+h4AQMmNJpbRaeZs45yMYyyu/FIi
hUazy7Rwk2vkWcuTd/sqH9b9y3VCYpN9juRaehEiK8qxXT3ydTU4Tub25BHmvXdr
dx5pShG4P3nAGnfV1qKAemyQcY7sjfMieqN1F3QcsRcxqZgySUm11o2JRw==
=sHsX
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more kvm fixes from Paolo Bonzini:
"Five small fixes.
The nested migration bug will be fixed with a better API in 5.10 or
5.11, for now this is a fix that works with existing userspace but
keeps the current ugly API"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SVM: Add a dedicated INVD intercept routine
KVM: x86: Reset MMU context if guest toggles CR4.SMAP or CR4.PKE
KVM: x86: fix MSR_IA32_TSC read for nested migration
selftests: kvm: Fix assert failure in single-step test
KVM: x86: VMX: Make smaller physical guest address space support user-configurable
A small collection of driver specific fixes, the fsl-espi and bcm-qspi
changes in particular have been causing breakage for users.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9uS/ETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HO5B/kBy15WzYCeJ1VqAq+HXliT8IvFuGMh
GgwIggHFRpqH9DBMA3PxrjHF9ULfu7wGA2hrSE6Mn2Cxnbt3qsPMU57yRuer9Zb9
ngWNID2BpbyWtXvwDcV7e+0N9ahsgynQR9aJ7JTRfhDBwsHSz9IWF+i6Aug0/I1Z
tDlEm8vhpIJcWuFKX1W7P1pLJ0y/1dqQHQh6vGajuj3c9EOuyrF1BjarfnhhokXL
iB3wdSaj6OAUmkvM4/fZdZrgMDtSoYurDSSTnl4XQPHavwqXbg64s57x/l25ye8N
Zz9lsH9nHCSrBPUnbAI4NpwlQtFx6z7aLUGJp7rcU2OSiSn6QnNc6ycF
=1ejb
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of driver specific fixes, the fsl-espi and bcm-qspi
changes in particular have been causing breakage for users"
* tag 'spi-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: bcm-qspi: Fix probe regression on iProc platforms
spi: fsl-dspi: fix use-after-free in remove path
spi: fsl-espi: Only process interrupts for expected events
spi: bcm2835: Make polling_limit_us static
spi: spi-fsl-dspi: use XSPI mode instead of DMA for DPAA2 SoCs
A single fix for incorrect specification of some of the register fields
on axp20x devices which would break voltage setting on affected systems.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9uTFQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0OEZB/9tRSg6gHVdp2OwAbWPzJQcHYYP4stQ
H3mPcsDJRmpVnHhUQe3qlUvG4QZ7bDhnHFYS1G7LFgEBNVhCwKtpnseaQMJaCaa+
t9LLWNtzltuo75995bBtPYcSQI6U0yUYbu7U7n+4vibh/pjqY3eNg4lLrWtVL/OC
FwkCEql5+ZTTg3OcRHzKlYe1UlOB0kSHNCjySiVytPrC0UH32gFCs/LSZxDR8lbo
a9x8Vi8brbcmpASoCY0d+c0hM6PWB/chNwVHGnoWYJ+xoJMVLzC8TN/mkUgG++9i
wnwXfbUd0EbLKuLrZto0qdx14n2nLp2YpeLJhTbsJaQ5C+FQGvv7D2v5
=Uvnh
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"A single fix for incorrect specification of some of the register
fields on axp20x devices which would break voltage setting on affected
systems"
* tag 'regulator-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: axp20x: fix LDO2/4 description
Two issues here - one is a fix for use after free issues in the case
where a regmap overrides its name using something dynamically generated,
the other is that we weren't handling access checks non-incrementing I/O
on registers within paged register regions correctly resulting in
spurious errors. Both of these are quite rare but serious if they
occur.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9uTagTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HQ0B/9rfdPyuAxvv21vDoQbVYI8vg98WOGg
gB+JJ1WKt9o6H3R64k8drgGB1DL/vWTub2+bkIoey0XMmIOsADBq/qrWeX4ziwpl
LhkDxBbTc1U0Wqkq2IONjQbp9pr4kJyoTxGc6BRyysO0TAcfrGD5JvSRru9SLiSc
cWpLq6YgL1KoLSEcvy5B7n9TydCEtNw8CpnalLvxFtmlthelFFHkCZmt2+R2fYVa
QsNGEPlmsiKEL7KXlnGrDcNsnJ59YBAicsaPMBUk0tGkbNt5ifdsSxUJbCmAV+41
yCt5QIlf0Ctjhb7m/Xm4efIOKbmyhGPmG7ZdrZMRXmmcLshFfxJkd+k+
=0+l/
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Two issues here - one is a fix for use after free issues in the case
where a regmap overrides its name using something dynamically
generated, the other is that we weren't handling access checks
non-incrementing I/O on registers within paged register regions
correctly resulting in spurious errors.
Both of these are quite rare but serious if they occur"
* tag 'regmap-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix page selection for noinc writes
regmap: fix page selection for noinc reads
regmap: debugfs: Add back in erroneously removed initialisation of ret
regmap: debugfs: Fix handling of name string for debugfs init delays
A previous commit for fixing up short reads botched the async retry
path, so we ended up going to worker threads more often than we should.
Fix this up, so retries work the way they originally were intended to.
Fixes: 227c0c9673 ("io_uring: internally retry short reads")
Reported-by: Hao_Xu <haoxu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- Export rcu_idle_{enter,exit} to modules to fix build issues
introduced by recent RCU-lockdep fixes (Borislav Petkov).
- Add missing return statement to a stub function in the ACPI
processor driver to fix a build issue introduced by recent
RCU-lockdep fixes (Rafael Wysocki).
- Fix recently introduced suspicious RCU usage warnings in the PSCI
cpuidle driver and drop stale comments regarding RCU_NONIDLE()
usage from enter_s2idle_proper() (Ulf Hansson).
- Fix error code path in the tegra30 devfreq driver (Dan Carpenter).
- Add missing information to devfreq_summary debugfs (Chanwoo Choi).
-----BEGIN PGP SIGNATURE-----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=lea/
-----END PGP SIGNATURE-----
Merge tag 'pm-5.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix more fallout of recent RCU-lockdep changes in CPU idle code
and two devfreq issues.
Specifics:
- Export rcu_idle_{enter,exit} to modules to fix build issues
introduced by recent RCU-lockdep fixes (Borislav Petkov)
- Add missing return statement to a stub function in the ACPI
processor driver to fix a build issue introduced by recent
RCU-lockdep fixes (Rafael Wysocki)
- Fix recently introduced suspicious RCU usage warnings in the PSCI
cpuidle driver and drop stale comments regarding RCU_NONIDLE()
usage from enter_s2idle_proper() (Ulf Hansson)
- Fix error code path in the tegra30 devfreq driver (Dan Carpenter)
- Add missing information to devfreq_summary debugfs (Chanwoo Choi)"
* tag 'pm-5.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: processor: Fix build for ARCH_APICTIMER_STOPS_ON_C3 unset
PM / devfreq: tegra30: Disable clock on error in probe
PM / devfreq: Add timer type to devfreq_summary debugfs
cpuidle: Drop misleading comments about RCU usage
cpuidle: psci: Fix suspicious RCU usage
rcu/tree: Export rcu_idle_{enter,exit} to modules
The INVD instruction intercept performs emulation. Emulation can't be done
on an SEV guest because the guest memory is encrypted.
Provide a dedicated intercept routine for the INVD intercept. And since
the instruction is emulated as a NOP, just skip it instead.
Fixes: 1654efcbc4 ("KVM: SVM: Add KVM_SEV_INIT command")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <a0b9a19ffa7fef86a3cc700c7ea01cb2731e04e5.1600972918.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
One fix for a bug that blktests hits when using rxe:
- Tear down the CQ pool before waiting for all references to go away
-----BEGIN PGP SIGNATURE-----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=XAp+
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fix from Jason Gunthorpe:
"One fix for a bug that blktests hits when using rxe: tear down the CQ
pool before waiting for all references to go away"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/core: Fix ordering of CQ pool destruction
dma-buf:
- Single null pointer deref fix for dma-buf
i915:
- Fix selftest reference to stack data out of scope
- Fix GVT null pointer dereference
-----BEGIN PGP SIGNATURE-----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=oVrS
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2020-09-25' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Fairly quiet, a couple of i915 fixes, one dma-buf fix, one vc4 and two
sun4i changes
dma-buf:
- Single null pointer deref fix
i915:
- Fix selftest reference to stack data out of scope
- Fix GVT null pointer dereference
vc4:
- fill asoc card owner
sun4i:
- program secondary CSC correctly"
* tag 'drm-fixes-2020-09-25' of git://anongit.freedesktop.org/drm/drm:
drm/i915/selftests: Push the fake iommu device from the stack to data
dmabuf: fix NULL pointer dereference in dma_buf_release()
drm/i915/gvt: Fix port number for BDW on EDID region setup
drm/sun4i: mixer: Extend regmap max_register
drm/sun4i: sun8i-csc: Secondary CSC register correction
drm/vc4/vc4_hdmi: fill ASoC card owner
This causes all the bios to be submitted with REQ_NOWAIT, which can be
problematic on either btrfs or on file systems that otherwise use a mix
of block devices where only some of them support it.
For now, just remove the setting of plug->nowait = true.
Reported-by: Dan Melnic <dmm@fb.com>
Reported-by: Brian Foster <bfoster@redhat.com>
Fixes: b63534c41e ("io_uring: re-issue block requests that failed because of resources")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 88b7381a93 ("USB: Select better matching USB drivers when
available") inadvertently broke usbip functionality. The commit in
question allows USB device drivers to be explicitly matched with
USB devices via the use of driver-provided identifier tables and
match functions, which is useful for a specialised device driver
to be chosen for a device that can also be handled by another,
more generic, device driver.
Prior, the USB device section of usb_device_match() had an
unconditional "return 1" statement, which allowed user-space to bind
USB devices to the usbip_host device driver, if desired. However,
the aforementioned commit changed the default/fallback return
value to zero. This breaks device drivers such as usbip_host, so
this commit restores the legacy behaviour, but only if a device
driver does not have an id_table and a match() function.
In addition, if usb_device_match is called for a device driver
and device pair where the device does not match the id_table of the
device driver in question, then the device driver will be disqualified
for the device. This allows avoiding the default case of "return 1",
which prevents undesirable probe() calls to a driver even though
its id_table did not match the device.
Finally, this commit changes the specialised-driver-to-generic-driver
transition code so that when a device driver returns -ENODEV, a more
generic device driver is only considered if the current device driver
does not have an id_table and a match() function. This ensures that
"generic" drivers such as usbip_host will not be considered specialised
device drivers and will not cause the device to be locked in to the
generic device driver, when a more specialised device driver could be
tried.
All of these changes restore usbip functionality without regressions,
ensure that the specialised/generic device driver selection logic works
as expected with the usb and apple-mfi-fastcharge drivers, and do not
negatively affect the use of devices provided by dummy_hcd.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-5-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit resolves a minor bug in the selection/discovery of more
specific USB device drivers for devices that are currently bound to
generic USB device drivers.
The bug is related to the way a candidate USB device driver is
compared against the generic USB device driver. The code in
is_dev_usb_generic_driver() assumes that the device driver in question
is a USB device driver by calling to_usb_device_driver(dev->driver)
to downcast; however I have observed that this assumption is not always
true, through code instrumentation.
This commit avoids the incorrect downcast altogether by comparing
the USB device's driver (i.e., dev->driver) to the generic USB
device driver directly. This method was suggested by Alan Stern.
This bug was found while investigating Andrey Konovalov's report
indicating usbip device driver misbehaviour with the recently merged
generic USB device driver selection feature. The report is linked
below.
Fixes: d5643d2249 ("USB: Fix device driver race")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-4-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit resolves a bug in the selection/discovery of more
specific USB device drivers for devices that are currently bound to
generic USB device drivers.
The bug is in the logic that determines whether a device currently
bound to a generic USB device driver should be re-probed by a
more specific USB device driver or not. The code in
__usb_bus_reprobe_drivers() used to have the following lines:
if (usb_device_match_id(udev, new_udriver->id_table) == NULL &&
(!new_udriver->match || new_udriver->match(udev) != 0))
return 0;
ret = device_reprobe(dev);
As the reader will notice, the code checks whether the USB device in
consideration matches the identifier table (id_table) of a specific
USB device_driver (new_udriver), followed by a similar check, but this
time with the USB device driver's match function. However, the match
function's return value is not checked correctly. When match() returns
zero, it means that the specific USB device driver is *not* applicable
to the USB device in question, but the code then goes on to reprobe the
device with the new USB device driver under consideration. All this to
say, the logic is inverted.
This bug was found by code inspection and instrumentation while
investigating the root cause of the issue reported by Andrey Konovalov,
where usbip took over syzkaller's virtual USB devices in an undesired
manner. The report is linked below.
Fixes: d5643d2249 ("USB: Fix device driver race")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-3-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit reverts commit 7a2f2974f2 ("usbip: Implement a match
function to fix usbip").
In summary, commit d5643d2249 ("USB: Fix device driver race")
inadvertently broke usbip functionality, which I resolved in an incorrect
manner by introducing a match function to usbip, usbip_match(), that
unconditionally returns true.
However, the usbip_match function, as is, causes usbip to take over
virtual devices used by syzkaller for USB fuzzing, which is a regression
reported by Andrey Konovalov.
Furthermore, in conjunction with the fix of another bug, handled by another
patch titled "usbcore/driver: Fix specific driver selection" in this patch
set, the usbip_match function causes unexpected USB subsystem behaviour
when the usbip_host driver is loaded. The unexpected behaviour can be
qualified as follows:
- If commit 41160802ab8e ("USB: Simplify USB ID table match") is included
in the kernel, then all USB devices are bound to the usbip_host
driver, which appears to the user as if all USB devices were
disconnected.
- If the same commit (41160802ab8e) is not in the kernel (as is the case
with v5.8.10) then all USB devices are re-probed and re-bound to their
original device drivers, which appears to the user as a disconnection
and re-connection of USB devices.
Please note that this commit will make usbip non-operational again,
until yet another patch in this patch set is merged, titled
"usbcore/driver: Accommodate usbip".
Cc: <stable@vger.kernel.org> # 5.8: 41160802ab8e: USB: Simplify USB ID table match
Cc: <stable@vger.kernel.org> # 5.8
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <syzkaller@googlegroups.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-2-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to move the closing of the src_device out of all the device
replace locking, but we definitely want to zero out the superblock
before we commit the last time to make sure the device is properly
removed. Handle this by pushing btrfs_scratch_superblocks into
btrfs_dev_replace_finishing, and then later on we'll move the src_device
closing and freeing stuff where we need it to be.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
commit 7b6620d7db ("block: remove REQ_NOWAIT_INLINE") removed the
REQ_NOWAIT_INLINE related code, but the diff wasn't applied to
blk_types.h somehow.
Then commit 2771cefeac ("block: remove the REQ_NOWAIT_INLINE flag")
removed the REQ_NOWAIT_INLINE flag while the BLK_QC_T_EAGAIN flag still
remains.
Fixes: 7b6620d7db ("block: remove REQ_NOWAIT_INLINE")
Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we cancel these requests, we'll leak the memory associated with the
filename. Add them to the table of ops that need cleaning, if
REQ_F_NEED_CLEANUP is set.
Cc: stable@vger.kernel.org
Fixes: e62753e4e2 ("io_uring: call statx directly")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reset the MMU context during kvm_set_cr4() if SMAP or PKE is toggled.
Recent commits to (correctly) not reload PDPTRs when SMAP/PKE are
toggled inadvertantly skipped the MMU context reset due to the mask
of bits that triggers PDPTR loads also being used to trigger MMU context
resets.
Fixes: 427890aff8 ("kvm: x86: Toggling CR4.SMAP does not load PDPTEs in PAE mode")
Fixes: cb957adb4e ("kvm: x86: Toggling CR4.PKE does not load PDPTEs in PAE mode")
Cc: Jim Mattson <jmattson@google.com>
Cc: Peter Shier <pshier@google.com>
Cc: Oliver Upton <oupton@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923215352.17756-1-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
drm/i915 fixes for v5.9-rc7:
- Fix selftest reference to stack data out of scope
- Fix GVT null pointer dereference
- Backmerge from Linus' master to fix build
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87zh5fpmha.fsf@intel.com
- fix error during controller probe that cause double free irqs
(Keith Busch)
- FC connection establishment fix (James Smart)
- properly handle completions for invalid tags (Xianting Tian)
- pass the correct nsid to the command effects and supported log
(Chaitanya Kulkarni)
-----BEGIN PGP SIGNATURE-----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=0x/v
-----END PGP SIGNATURE-----
Merge tag 'nvme-5.9-2020-09-24' of git://git.infradead.org/nvme into block-5.9
Pull NVMe fixes from Christoph:
"nvme fixes for 5.9
- fix error during controller probe that cause double free irqs
(Keith Busch)
- FC connection establishment fix (James Smart)
- properly handle completions for invalid tags (Xianting Tian)
- pass the correct nsid to the command effects and supported log
(Chaitanya Kulkarni)"
* tag 'nvme-5.9-2020-09-24' of git://git.infradead.org/nvme:
nvme-core: don't use NVME_NSID_ALL for command effects and supported log
nvme-fc: fail new connections to a deleted host or remote port
nvme-pci: fix NULL req in completion handler
nvme: return errors for hwmon init
MSR reads/writes should always access the L1 state, since the (nested)
hypervisor should intercept all the msrs it wants to adjust, and these
that it doesn't should be read by the guest as if the host had read it.
However IA32_TSC is an exception. Even when not intercepted, guest still
reads the value + TSC offset.
The write however does not take any TSC offset into account.
This is documented in Intel's SDM and seems also to happen on AMD as well.
This creates a problem when userspace wants to read the IA32_TSC value and then
write it. (e.g for migration)
In this case it reads L2 value but write is interpreted as an L1 value.
To fix this make the userspace initiated reads of IA32_TSC return L1 value
as well.
Huge thanks to Dave Gilbert for helping me understand this very confusing
semantic of MSR writes.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200921103805.9102-2-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----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=xTpy
-----END PGP SIGNATURE-----
Merge tag 'media/v5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- fix a regression at the CEC adapter core
- two uAPI patches (one revert) for changes in this development cycle
* tag 'media/v5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: dt-bindings: media: imx274: Convert to json-schema
media: media/v4l2: remove V4L2_FLAG_MEMORY_NON_CONSISTENT flag
media: cec-adap.c: don't use flush_scheduled_work()
Just a handful small device-specific fixes including a couple of
reverts.
-----BEGIN PGP SIGNATURE-----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=PgF0
-----END PGP SIGNATURE-----
Merge tag 'sound-5.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a handful small device-specific fixes including a couple of
reverts"
* tag 'sound-5.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
Revert "ALSA: usb-audio: Disable Lenovo P620 Rear line-in volume control"
Revert "ALSA: hda - Fix silent audio output and corrupted input on MSI X570-A PRO"
ALSA: usb-audio: Add delay quirk for H570e USB headsets
ALSA: hda/realtek: Enable front panel headset LED on Lenovo ThinkStation P520
ALSA: hda/realtek - Couldn't detect Mic if booting with headset plugged
ALSA: asihpi: fix iounmap in error handler
PowerPC allmodconfig often fails to build as follows:
LD .tmp_vmlinux.kallsyms1
KSYM .tmp_vmlinux.kallsyms1.o
LD .tmp_vmlinux.kallsyms2
KSYM .tmp_vmlinux.kallsyms2.o
LD .tmp_vmlinux.kallsyms3
KSYM .tmp_vmlinux.kallsyms3.o
LD vmlinux
SORTTAB vmlinux
SYSMAP System.map
Inconsistent kallsyms data
Try make KALLSYMS_EXTRA_PASS=1 as a workaround
make[2]: *** [../Makefile:1162: vmlinux] Error 1
Setting KALLSYMS_EXTRA_PASS=1 does not help.
This is caused by the compiler inserting stubs such as *.long_branch.*
and *.plt_branch.*
$ powerpc-linux-nm -n .tmp_vmlinux.kallsyms2
[ snip ]
c00000000210c010 t 00000075.plt_branch.da9:19
c00000000210c020 t 00000075.plt_branch.1677:5
c00000000210c030 t 00000075.long_branch.memmove
c00000000210c034 t 00000075.plt_branch.9e0:5
c00000000210c044 t 00000075.plt_branch.free_initrd_mem
...
Actually, the problem mentioned in scripts/link-vmlinux.sh comments;
"In theory it's possible this results in even more stubs, but unlikely"
is happening here, and ends up with another kallsyms step required.
scripts/kallsyms.c already ignores various compiler stubs. Let's do
similar to make kallsysms for PowerPC always succeed in 2 steps.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Commit 09854ba94c ("mm: do_wp_page() simplification") reorganized all
the code around the page re-use vs copy, but in the process also moved
the final unlock_page() around to after the wp_page_reuse() call.
That normally doesn't matter - but it means that the unlock_page() is
now done after releasing the page table lock. Again, not a big deal,
you'd think.
But it turns out that it's very wrong indeed, because once we've
released the page table lock, we've basically lost our only reference to
the page - the page tables - and it could now be free'd at any time. We
do hold the mmap_sem, so no actual unmap() can happen, but madvise can
come in and a MADV_DONTNEED will zap the page range - and free the page.
So now the page may be free'd just as we're unlocking it, which in turn
will usually trigger a "Bad page state" error in the freeing path. To
make matters more confusing, by the time the debug code prints out the
page state, the unlock has typically completed and everything looks fine
again.
This all doesn't happen in any normal situations, but it does trigger
with the dirtyc0w_child LTP test. And it seems to trigger much more
easily (but not expclusively) on s390 than elsewhere, probably because
s390 doesn't do the "batch pages up for freeing after the TLB flush"
that gives the unlock_page() more time to complete and makes the race
harder to hit.
Fixes: 09854ba94c ("mm: do_wp_page() simplification")
Link: https://lore.kernel.org/lkml/a46e9bbef2ed4e17778f5615e818526ef848d791.camel@redhat.com/
Link: https://lore.kernel.org/linux-mm/c41149a8-211e-390b-af1d-d5eee690fecb@linux.alibaba.com/
Reported-by: Qian Cai <cai@redhat.com>
Reported-by: Alex Shi <alex.shi@linux.alibaba.com>
Bisected-and-analyzed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Tested-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GPIO_U is mapped to the least significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_U is input only. All
the other bits need to be 1 because GPIO_V/W/X support both input and
output modes.
Similarly, GPIO_Y/Z are mapped to the 2 least significant bytes, and the
according bits need to be 1 because GPIO_Y/Z support both input and
output modes.
Fixes: ab4a85534c ("gpio: aspeed: Add in ast2600 details to Aspeed driver")
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Currently, the IRQ setup for the SGPIO driver enables all interrupts in
dual-edge trigger mode. Since the default handler is handle_bad_irq, any
state change on input GPIOs will trigger bad IRQ warnings.
This change applies sensible IRQ defaults: single-edge trigger, and all
IRQs disabled.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When pca953x_irq_pending returns false, the pending parameter won't
be set. But pca953x_irq_handler continues using this uninitialized
variable as pending irqs and will cause problem.
Fix the issue by initializing pending to 0.
Fixes: 064c73afe7 ("gpio: pca953x: Synchronize interrupt handler properly")
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Commit 653055b9ac ("vhost-vdpa: support get/set backend features")
introduces two malfunction backend features ioctls:
1) the ioctls was blindly added to vring ioctl instead of vdpa device
ioctl
2) vhost_set_backend_features() was called when dev mutex has already
been held which will lead a deadlock
This patch fixes the above issues.
Cc: Eli Cohen <elic@nvidia.com>
Reported-by: Zhu Lingshan <lingshan.zhu@intel.com>
Fixes: 653055b9ac ("vhost-vdpa: support get/set backend features")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20200907104343.31141-1-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
if of_find_device_by_node() succeed, exynos_iommu_of_xlate() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: aa759fd376 ("iommu/exynos: Add callback for initializing devices from device tree")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200918011335.909141-1-yukuai3@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
reqcnt is an u32 pointer but we do copy sizeof(reqcnt) which is the
size of the pointer. This means we only copy 8 byte. Let us copy
the full monty.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: stable@vger.kernel.org
Fixes: af4a72276d ("s390/zcrypt: Support up to 256 crypto adapters.")
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Masami discovered two bugs which this fixes and he added tests to
cover these issues.
- Fix a bug that breaks bootconfig tree nodes
- Fix a bug that does not truncate whitespace properly
- Add tests to cover the above two cases
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCX2uLGBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qh/dAP0Qgh1L4y13NgRRFVYFic8f3gcsFf3s
z0rNCzYabJkjvgD9GjoAdxYABxMnM7KVKwH8OCpcANIFo9Ry5oRJL5mSsgk=
=z4GW
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.9-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull bootconfig fixes from Steven Rostedt:
"A couple of fixes for bootconfig.
Masami discovered two bugs which this fixes and he added tests to
cover these issues.
- Fix a bug that breaks bootconfig tree nodes
- Fix a bug that does not truncate whitespace properly
- Add tests to cover the above two cases"
* tag 'trace-v5.9-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tools/bootconfig: Add testcase for tailing space
tools/bootconfig: Add testcases for repeated key with brace
lib/bootconfig: Fix to remove tailing spaces after value
lib/bootconfig: Fix a bug of breaking existing tree nodes
because past attempts didn't fully appreciate the liability relative
to recursive bio splitting. This fix limits DM's bio splitting to a
single method and does _not_ use blk_queue_split() for normal IO.
- DM crypt Documentation updates for features added during 5.9 merge.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEJfWUX4UqZ4x1O2wixSPxCi2dA1oFAl9rgpcTHHNuaXR6ZXJA
cmVkaGF0LmNvbQAKCRDFI/EKLZ0DWlD3CACN3y3rirJb7uFnQmg/VINktKEd4Ntj
Or5hPNpXhxv5eAZAzrgKyr+fdC21amfSvbfQW7iNnY6rn9JweEwC9nqLW/swMa7o
1cyThdvpUbR9e++UVMg9GX3F3L5RoFApRZBOUii6FZVR0R8THyaODlPkBOnST1cY
L5qhemlWpLVLKJ4FIeNJ+i7BgVvFrkueaqiFycKBvORFfaT04TUHjS+iCDuujala
sYlze3/nA++SC3XdNkS0/paXqneWs452ceJrKIDWsZJ5NXV5OAm+BNtqHad3P6M4
AfMG8vjw9q1Ge0e2mbTRvm+Z1X2S7b3Zwh7sS3OlTTcaa19Bk4XG3RsD
=487e
-----END PGP SIGNATURE-----
Merge tag 'for-5.9/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- DM core fix for incorrect double bio splitting. Keep "fixing" this
because past attempts didn't fully appreciate the liability relative
to recursive bio splitting. This fix limits DM's bio splitting to a
single method and does _not_ use blk_queue_split() for normal IO.
- DM crypt Documentation updates for features added during 5.9 merge.
* tag 'for-5.9/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm crypt: document encrypted keyring key option
dm crypt: document new no_workqueue flags
dm: fix comment in dm_process_bio()
dm: fix bio splitting and its bio completion order for regular IO
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE8rQSAMVO+zA4DBdWxWXV+ddtWDsFAl9q8PUACgkQxWXV+ddt
WDsHZg//YF3Rfeo7/zaRsfUPvNoKDcM69TW+HROJXu4+rYlOukyuh5T+wboRU1Ft
7ymiR18idPYbtOczmH1Pqw+3wyOr39WafcvAnndoUguXJHsUrriBNqkthQICt0CG
hUUiofedaB+j+ti7AYGhF/tkqjd8LkCj8SGEz4cSUFCheIHR+ajFwFmx1Sw6NGJV
h9SdKfbBpIqIpoExFhprNFlxdaKN9rlhYY+zXZYeCBdU6r89CkuLqxZ79GzaU0N7
PG7FxuuJXvyHhta2a6p8hnEp7perOG22OTXJhzXd5JXiNCfZ/w4SfhH/aPO/3t5V
x42hO+FvloVSLS3woZqkBsCgCIe0a3QOT0YxZiM+1cwSgg8mVw4UBEB3PIgkfOVT
LawMbcgSh1evsSazru8gujm4f8RVxpSxxWfhhRwjXtyB8K89e22yBa9Lwfj04SH7
O5O7VrLDDnHsQWinsEf4Rl6byA13jUCgI5eUxZ5B7Au0Pm9uMexDh3lvgE0W0ucY
UvD8qAetu2NNZD68gZp597uHPrwu+Lr+VumIh4wF6doeShlIkbf/d+ntOgW9ey1S
WFSh7sUdKg5pVf6KJQ4yc3aBA6un5lv9LnvPJOwc9HyMUj/cYuxywxWf1YMr5umv
7/6CkufYjTAmEERQeqE1I6UIgUiWkS9nIisB8BLbYkrMR9Wi1bs=
=tFUE
-----END PGP SIGNATURE-----
Merge tag 'for-5.9-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"syzkaller started to hit us with reports, here's a fix for one type
(stack overflow when printing checksums on read error).
The other patch is a fix for sysfs object, we have a test for that and
it leads to a crash."
* tag 'for-5.9-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix put of uninitialized kobject after seed device delete
btrfs: fix overflow when copying corrupt csums for a message
Several people reported in the kernel bugzilla that between v4.12 and v4.13
the magic which works around broken hardware and BIOSes to find the proper
timer interrupt delivery mode stopped working for some older affected
platforms which need to fall back to ExtINT delivery mode.
The reason is that the core code changed to keep track of the masked and
disabled state of an interrupt line more accurately to avoid the expensive
hardware operations.
That broke an assumption in i8259_make_irq() which invokes
disable_irq_nosync();
irq_set_chip_and_handler();
enable_irq();
Up to v4.12 this worked because enable_irq() unconditionally unmasked the
interrupt line, but after the state tracking improvements this is not
longer the case because the IO/APIC uses lazy disabling. So the line state
is unmasked which means that enable_irq() does not call into the new irq
chip to unmask it.
In principle this is a shortcoming of the core code, but it's more than
unclear whether the core code should try to reset state. At least this
cannot be done unconditionally as that would break other existing use cases
where the chip type is changed, e.g. when changing the trigger type, but
the callers expect the state to be preserved.
As the way how check_timer() is switching the delivery modes is truly
unique, the obvious fix is to simply unmask the i8259 manually after
changing the mode to ExtINT delivery and switching the irq chip to the
legacy PIC.
Note, that the fixes tag is not really precise, but identifies the commit
which broke the assumptions in the IO/APIC and i8259 code and that's the
kernel version to which this needs to be backported.
Fixes: bf22ff45be ("genirq: Avoid unnecessary low level irq function calls")
Reported-by: p_c_chan@hotmail.com
Reported-by: ecm4@mail.com
Reported-by: perdigao1@yahoo.com
Reported-by: matzes@users.sourceforge.net
Reported-by: rvelascog@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: p_c_chan@hotmail.com
Tested-by: matzes@users.sourceforge.net
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197769
In the function nvme_get_effects_log() it uses NVME_NSID_ALL which has
namespace scope. The command effect log page is controller specific.
Replace NVME_NSID_ALL with 0x00 which specifies the controller scope
instead of namespace scope.
Fixes: 84fef62d13 ("nvme: check admin passthru command effects")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209287
Reported-by: Huai-Cheng Kuo <hh81478072@gmail.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Gao Xiang