After commit c9eeec26e3 ("tcp: TSQ can use a dynamic limit"), several
users reported throughput regressions, notably on mvneta and wifi
adapters.
802.11 AMPDU requires a fair amount of queueing to be effective.
This patch partially reverts the change done in tcp_write_xmit()
so that the minimal amount is sysctl_tcp_limit_output_bytes.
It also remove the use of this sysctl while building skb stored
in write queue, as TSO autosizing does the right thing anyway.
Users with well behaving NICS and correct qdisc (like sch_fq),
can then lower the default sysctl_tcp_limit_output_bytes value from
128KB to 8KB.
This new usage of sysctl_tcp_limit_output_bytes permits each driver
authors to check how their driver performs when/if the value is set
to a minimum of 4KB.
Normally, line rate for a single TCP flow should be possible,
but some drivers rely on timers to perform TX completion and
too long TX completion delays prevent reaching full throughput.
Fixes: c9eeec26e3 ("tcp: TSQ can use a dynamic limit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sujith Manoharan <sujith@msujith.org>
Reported-by: Arnaud Ebalard <arno@natisbad.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new documentation for the packets_per_slave option available
for balance-rr mode.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
here's a pull request for net-next.
It includes a patch by Oliver Hartkopp et al. that adds documentation
for the broadcast manager to Documentation/networking/can.txt. Three
patches by me that clean up the netlink handling code in the CAN core.
And another patch that removes a not needed function from the ti_hecc
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Slow start now increases cwnd by 1 if an ACK acknowledges some packets,
regardless the number of packets. Consequently slow start performance
is highly dependent on the degree of the stretch ACKs caused by
receiver or network ACK compression mechanisms (e.g., delayed-ACK,
GRO, etc). But slow start algorithm is to send twice the amount of
packets of packets left so it should process a stretch ACK of degree
N as if N ACKs of degree 1, then exits when cwnd exceeds ssthresh. A
follow up patch will use the remainder of the N (if greater than 1)
to adjust cwnd in the congestion avoidance phase.
In addition this patch retires the experimental limited slow start
(LSS) feature. LSS has multiple drawbacks but questionable benefit. The
fractional cwnd increase in LSS requires a loop in slow start even
though it's rarely used. Configuring such an increase step via a global
sysctl on different BDPS seems hard. Finally and most importantly the
slow start overshoot concern is now better covered by the Hybrid slow
start (hystart) enabled by default.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications have started to use Fast Open (e.g., Chrome browser has
such an optional flag) and the feature has gone through several
generations of kernels since 3.7 with many real network tests. It's
time to enable this flag by default for applications to test more
conveniently and extensively.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Joby Poriyath provided a xen-netback patch to reduce the size of
xenvif structure as some netdev allocation could fail under
memory pressure/fragmentation.
This patch is handling the problem at the core level, allowing
any netdev structures to use vmalloc() if kmalloc() failed.
As vmalloc() adds overhead on a critical network path, add __GFP_REPEAT
to kzalloc() flags to do this fallback only when really needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Joby Poriyath <joby.poriyath@citrix.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation about the broadcast manager. It's based on Brian
Thorne's initial patch http://marc.info/?l=linux-can&m=138119382015496&w=2 and
Daniele Venzano's work http://brownhat.org/docs/socketcan.html .
Signed-off-by: Brian Thorne <hardbyte@gmail.com>
Cc: Daniele Venzano <linux@brownhat.org>
Cc: Andre Naujoks <nautsch2@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Correct spelling typo in Documentation/networking
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various typo fixes to netdev-FAQ.txt:
- capitalize Linux
- hyphenate dual-word adjectives
- minor punctuation fixes
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My university will stop email service for alumni in january 2014, please
use my new e-mail address instead.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This is replaced by a userspace program, we don't need this
functionality to bloat the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Add new documentation for encap2+3 and encap3+4, also update the formula
for the old modes due to the changes.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
running bonding in ALB mode requires that learning packets be sent periodically,
so that the switch knows where to send responding traffic. However, depending
on switch configuration, there may not be any need to send traffic at the
default rate of 3 packets per second, which represents little more than wasted
data. Allow the ALB learning packet interval to be made configurable via sysfs
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Acked-by: Veaceslav Falico <vfalico@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the changes for Kconfig, i40e.txt, MAINTAINERS, Kbuild
and new i40e/Makefile to build i40e with the kernel.
New driver build option is CONFIG_I40E
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Document force_mld_version parameter in ip-sysctl.txt.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some synopsys ip implementation doesn't support DMA store and forward mode,
such as BF60x. So, set force_thresh_dma_mode to use DMA thresholds only.
Update document and devicetree as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update documentation to add fanout policies that are available.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After hearing many people over past years complaining against TSO being
bursty or even buggy, we are proud to present automatic sizing of TSO
packets.
One part of the problem is that tcp_tso_should_defer() uses an heuristic
relying on upcoming ACKS instead of a timer, but more generally, having
big TSO packets makes little sense for low rates, as it tends to create
micro bursts on the network, and general consensus is to reduce the
buffering amount.
This patch introduces a per socket sk_pacing_rate, that approximates
the current sending rate, and allows us to size the TSO packets so
that we try to send one packet every ms.
This field could be set by other transports.
Patch has no impact for high speed flows, where having large TSO packets
makes sense to reach line rate.
For other flows, this helps better packet scheduling and ACK clocking.
This patch increases performance of TCP flows in lossy environments.
A new sysctl (tcp_min_tso_segs) is added, to specify the
minimal size of a TSO packet (default being 2).
A follow-up patch will provide a new packet scheduler (FQ), using
sk_pacing_rate as an input to perform optional per flow pacing.
This explains why we chose to set sk_pacing_rate to twice the current
rate, allowing 'slow start' ramp up.
sk_pacing_rate = 2 * cwnd * mss / srtt
v2: Neal Cardwell reported a suspect deferring of last two segments on
initial write of 10 MSS, I had to change tcp_tso_should_defer() to take
into account tp->xmit_size_goal_segs
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Van Jacobson <vanj@google.com>
Cc: Tom Herbert <therbert@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements RFC6980: Drop fragmented ndisc packets by
default. If a fragmented ndisc packet is received the user is informed
that it is possible to disable the check.
Cc: Fernando Gont <fernando@gont.com.ar>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross says:
====================
A number of significant new features and optimizations for net-next/3.12.
Highlights are:
* "Megaflows", an optimization that allows userspace to specify which
flow fields were used to compute the results of the flow lookup.
This allows for a major reduction in flow setups (the major
performance bottleneck in Open vSwitch) without reducing flexibility.
* Converting netlink dump operations to use RCU, allowing for
additional parallelism in userspace.
* Matching and modifying SCTP protocol fields.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates the documentation to the Intel wired LAN drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wildcarded flow support in kernel datapath.
Wildcarded flow can improve OVS flow set up performance by avoid sending
matching new flows to the user space program. The exact performance boost
will largely dependent on wildcarded flow hit rate.
In case all new flows hits wildcard flows, the flow set up rate is
within 5% of that of linux bridge module.
Pravin has made significant contributions to this patch. Including API
clean ups and bug fixes.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Conflicts:
net/netfilter/nf_conntrack_proto_tcp.c
The conflict had to do with overlapping changes dealing with
fixing the use of an "s32" to hold the value returned by
NAT_OFFSET().
Pablo Neira Ayuso says:
====================
The following batch contains Netfilter/IPVS updates for your net-next tree.
More specifically, they are:
* Trivial typo fix in xt_addrtype, from Phil Oester.
* Remove net_ratelimit in the conntrack logging for consistency with other
logging subsystem, from Patrick McHardy.
* Remove unneeded includes from the recently added xt_connlabel support, from
Florian Westphal.
* Allow to update conntracks via nfqueue, don't need NFQA_CFG_F_CONNTRACK for
this, from Florian Westphal.
* Remove tproxy core, now that we have socket early demux, from Florian
Westphal.
* A couple of patches to refactor conntrack event reporting to save a good
bunch of lines, from Florian Westphal.
* Fix missing locking in NAT sequence adjustment, it did not manifested in
any known bug so far, from Patrick McHardy.
* Change sequence number adjustment variable to 32 bits, to delay the
possible early overflow in long standing connections, also from Patrick.
* Comestic cleanups for IPVS, from Dragos Foianu.
* Fix possible null dereference in IPVS in the SH scheduler, from Daniel
Borkmann.
* Allow to attach conntrack expectations via nfqueue. Before this patch, you
had to use ctnetlink instead, thus, we save the conntrack lookup.
* Export xt_rpfilter and xt_HMARK header files, from Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cab70040df ("net: igmp:
Reduce Unsolicited report interval to 1s when using IGMPv3") and
2690048c01 ("net: igmp: Allow user-space
configuration of igmp unsolicited report interval") by William Manley made
igmp unsolicited report intervals configurable per interface and corrected
the interval of unsolicited igmpv3 report messages resendings to 1s.
Same needs to be done for IPv6:
MLDv1 (RFC2710 7.10.): 10 seconds
MLDv2 (RFC3810 9.11.): 1 second
Both intervals are configurable via new procfs knobs
mldv1_unsolicited_report_interval and mldv2_unsolicited_report_interval.
(also added .force_mld_version to ipv6_devconf_dflt to bring structs in
line without semantic changes)
v2:
a) Joined documentation update for IPv4 and IPv6 MLD/IGMP
unsolicited_report_interval procfs knobs.
b) incorporate stylistic feedback from William Manley
v3:
a) add new DEVCONF_* values to the end of the enum (thanks to David
Miller)
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: William Manley <william.manley@youview.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the last module parameter for SCTP and make this
configurable via sysctl for SCTP like all the rest of SCTP's
configuration knobs.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A collection of expectations and operational details about how
networking development takes place in the context of the netdev
mailing list.
The content is meant to capture specific items that are unique
to netdev workflow, and not re-document generic linux expectations
that are already captured elsewhere.
This was originally proposed[1] as a regular posting mailing list
FAQ, but it probably is more universally accessible here in tree.
[1] https://lwn.net/Articles/559211/
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The module was "permanent", due to the special tproxy skb->destructor.
Nowadays we have tcp early demux and its sock_edemux destructor in
networking core which can be used instead.
Thanks to early demux changes the input path now also handles
"skb->sk is tw socket" correctly, so this no longer needs the special
handling introduced with commit d503b30bd6
(netfilter: tproxy: do not assign timewait sockets to skb->sk).
Thus:
- move assign_sock function to where its needed
- don't prevent timewait sockets from being assigned to the skb
- remove nf_tproxy_core.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
| If you want to test which effects syncookies have to your
| network connections you can set this knob to 2 to enable
| unconditionally generation of syncookies.
Original idea and first implementation by Eric Dumazet.
Cc: Florian Westphal <fw@strlen.de>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Idea of this patch is to add optional limitation of number of
unsent bytes in TCP sockets, to reduce usage of kernel memory.
TCP receiver might announce a big window, and TCP sender autotuning
might allow a large amount of bytes in write queue, but this has little
performance impact if a large part of this buffering is wasted :
Write queue needs to be large only to deal with large BDP, not
necessarily to cope with scheduling delays (incoming ACKS make room
for the application to queue more bytes)
For most workloads, using a value of 128 KB or less is OK to give
applications enough time to react to POLLOUT events in time
(or being awaken in a blocking sendmsg())
This patch adds two ways to set the limit :
1) Per socket option TCP_NOTSENT_LOWAT
2) A sysctl (/proc/sys/net/ipv4/tcp_notsent_lowat) for sockets
not using TCP_NOTSENT_LOWAT socket option (or setting a zero value)
Default value being UINT_MAX (0xFFFFFFFF), meaning this has no effect.
This changes poll()/select()/epoll() to report POLLOUT
only if number of unsent bytes is below tp->nosent_lowat
Note this might increase number of sendmsg()/sendfile() calls
when using non blocking sockets,
and increase number of context switches for blocking sockets.
Note this is not related to SO_SNDLOWAT (as SO_SNDLOWAT is
defined as :
Specify the minimum number of bytes in the buffer until
the socket layer will pass the data to the protocol)
Tested:
netperf sessions, and watching /proc/net/protocols "memory" column for TCP
With 200 concurrent netperf -t TCP_STREAM sessions, amount of kernel memory
used by TCP buffers shrinks by ~55 % (20567 pages instead of 45458)
lpq83:~# echo -1 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# (super_netperf 200 -t TCP_STREAM -H remote -l 90 &); sleep 60 ; grep TCP /proc/net/protocols
TCPv6 1880 2 45458 no 208 yes ipv6 y y y y y y y y y y y y y n y y y y y
TCP 1696 508 45458 no 208 yes kernel y y y y y y y y y y y y y n y y y y y
lpq83:~# echo 131072 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# (super_netperf 200 -t TCP_STREAM -H remote -l 90 &); sleep 60 ; grep TCP /proc/net/protocols
TCPv6 1880 2 20567 no 208 yes ipv6 y y y y y y y y y y y y y n y y y y y
TCP 1696 508 20567 no 208 yes kernel y y y y y y y y y y y y y n y y y y y
Using 128KB has no bad effect on the throughput or cpu usage
of a single flow, although there is an increase of context switches.
A bonus is that we hold socket lock for a shorter amount
of time and should improve latencies of ACK processing.
lpq83:~# echo -1 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# perf stat -e context-switches ./netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3
OMNI Send TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.7.84 () port 0 AF_INET : +/-2.500% @ 99% conf.
Local Remote Local Elapsed Throughput Throughput Local Local Remote Remote Local Remote Service
Send Socket Recv Socket Send Time Units CPU CPU CPU CPU Service Service Demand
Size Size Size (sec) Util Util Util Util Demand Demand Units
Final Final % Method % Method
1651584 6291456 16384 20.00 17447.90 10^6bits/s 3.13 S -1.00 U 0.353 -1.000 usec/KB
Performance counter stats for './netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3':
412,514 context-switches
200.034645535 seconds time elapsed
lpq83:~# echo 131072 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# perf stat -e context-switches ./netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3
OMNI Send TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.7.84 () port 0 AF_INET : +/-2.500% @ 99% conf.
Local Remote Local Elapsed Throughput Throughput Local Local Remote Remote Local Remote Service
Send Socket Recv Socket Send Time Units CPU CPU CPU CPU Service Service Demand
Size Size Size (sec) Util Util Util Util Demand Demand Units
Final Final % Method % Method
1593240 6291456 16384 20.00 17321.16 10^6bits/s 3.35 S -1.00 U 0.381 -1.000 usec/KB
Performance counter stats for './netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3':
2,675,818 context-switches
200.029651391 seconds time elapsed
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-By: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP mailing list address to send patches or questions
to is linux-sctp@vger.kernel.org and not
lksctp-developers@lists.sourceforge.net anymore. Therefore,
update all occurences.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following batch contains Netfilter/IPVS updates for net-next,
they are:
* Enforce policy to several nfnetlink subsystem, from Daniel
Borkmann.
* Use xt_socket to match the third packet (to perform simplistic
socket-based stateful filtering), from Eric Dumazet.
* Avoid large timeout for picked up from the middle TCP flows,
from Florian Westphal.
* Exclude IPVS from struct net if IPVS is disabled and removal
of unnecessary included header file, from JunweiZhang.
* Release SCTP connection immediately under load, to mimic current
TCP behaviour, from Julian Anastasov.
* Replace and enhance SCTP state machine, from Julian Anastasov.
* Add tweak to reduce sync traffic in the presence of persistence,
also from Julian Anastasov.
* Add tweak for the IPVS SH scheduler not to reject connections
directed to a server, choose a new one instead, from Alexander
Frolkin.
* Add support for sloppy TCP and SCTP modes, that creates state
information on any packet, not only initial handshake packets,
from Alexander Frolkin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sync_persist_mode flag to reduce sync traffic
by syncing only persistent templates.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Currently, we fail only when all of the ips in arp_ip_target are gone.
However, in some situations we might need to fail if even one host from
arp_ip_target becomes unavailable.
All situations, obviously, rely on the idea that we need *completely*
functional network, with all interfaces/addresses working correctly.
One real world example might be:
vlans on top on bond (hybrid port). If bond and vlans have ips assigned
and we have their peers monitored via arp_ip_target - in case of switch
misconfiguration (trunk/access port), slave driver malfunction or
tagged/untagged traffic dropped on the way - we will be able to switch
to another slave.
Though any other configuration needs that if we need to have access to all
arp_ip_targets.
This patch adds this possibility by adding a new parameter -
arp_all_targets (both as a module parameter and as a sysfs knob). It can be
set to:
0 or any (the default) - which works exactly as it's working now -
the slave is up if any of the arp_ip_targets are up.
1 or all - the slave is up if all of the arp_ip_targets are up.
This parameter can be changed on the fly (via sysfs), and requires the mode
to be active-backup and arp_validate to be enabled (it obeys the
arp_validate config on which slaves to validate).
Internally it's done through:
1) Add target_last_arp_rx[BOND_MAX_ARP_TARGETS] array to slave struct. It's
an array of jiffies, meaning that slave->target_last_arp_rx[i] is the
last time we've received arp from bond->params.arp_targets[i] on this
slave.
2) If we successfully validate an arp from bond->params.arp_targets[i] in
bond_validate_arp() - update the slave->target_last_arp_rx[i] with the
current jiffies value.
3) When getting slave's last_rx via slave_last_rx(), we return the oldest
time when we've received an arp from any address in
bond->params.arp_targets[].
If the value of arp_all_targets == 0 - we still work the same way as
before.
Also, update the documentation to reflect the new parameter.
v3->v4:
Kill the forgotten rtnl_unlock(), rephrase the documentation part to be
more clear, don't fail setting arp_all_targets if arp_validate is not set -
it has no effect anyway but can be easier to set up. Also, print a warning
if the last arp_ip_target is removed while the arp_interval is on, but not
the arp_validate.
v2->v3:
Use _bh spinlock, remove useless rtnl_lock() and use jiffies for new
arp_ip_target last arp, instead of slave_last_rx(). On bond_enslave(),
use the same initialization value for target_last_arp_rx[] as is used
for the default last_arp_rx, to avoid useless interface flaps.
Also, instead of failing to remove the last arp_ip_target just print a
warning - otherwise it might break existing scripts.
v1->v2:
Correctly handle adding/removing hosts in arp_ip_target - we need to
shift/initialize all slave's target_last_arp_rx. Also, don't fail module
loading on arp_all_targets misconfiguration, just disable it, and some
minor style fixes.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some details to bonding documentation on how backup slave arp
validation works.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syncookies is on for default since in commit e994b7c901
(tcp: Don't make syn cookies initial setting depend on CONFIG_SYSCTL).
And fix a typo of CONFIG_SYN_COOKIES.
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 6648bd7e0e (ipv4: Add sysctl knob to control
early socket demux) introduced such sysctl, but forgot to add
doc into Documentation/networking/ip-sysctl.txt. This patch adds it.
Basically I grab the doc from the description of commit 41063e9dd1
(ipv4: Early TCP socket demux.) and the above commit.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes icmp_ignore_bogus_error_responses default value to be 1 instead
of FALSE. It is initialized to 1 in icmp_sk_init().
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplifies the tpacket_v3 example code a bit by getting rid
of unecessary macro wrappers, removing some debugging code so that it is
more to the point, and also adds a header comment. Now this example code
is the very minimum one needs to start from when dealing with tpacket_v3
and ~100 lines smaller than before.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrected the words Accsess to Access.
Signed-off-by: Stefan Huber <steffhip@googlemail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As Stephen proposed:
Since bonding supports configuration via iproute (netlink) and sysfs, I think
it is time to purge the old ifenslave code out of Documentation/networking
and update the documentation.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet