In order to let a const irqchip be fed to the irqchip layer, adjust
the various prototypes. An extra cast in irq_domain_set_hwirq_and_chip()
is required to avoid a warning.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220209162607.1118325-2-maz@kernel.org
As a preparation to moving the reference to the device used for
runtime power management, add a new 'dev' field to the irqdomain
structure for that exact purpose.
The irq_chip_pm_{get,put}() helpers are made aware of the dual
location via a new private helper.
No functional change intended.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220201120310.878267-2-maz@kernel.org
The only usage of irq_generic_chip_ops is to pass its address to
irq_domain_add_linear() which takes a pointer to const struct
irq_domain_ops. Make it const to allow the compiler to put it in
read-only memory.
[ tglx: Fixed subject prefix ]
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20211130214043.1257585-1-rikard.falkeborn@gmail.com
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
of_phandle_args_to_fwspec() can be generally useful to code extracting a DT
of_phandle and using an irq_fwspec to use the hierarchical irqdomain API.
Make it visible to the rest of the kernel, including modules.
Link: https://lore.kernel.org/r/20210929163847.2807812-2-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The 'size' is used in struct_size(domain, revmap, size) and its input
parameter type is 'size_t'(unsigned int).
Changing the size to 'unsigned int' to make the type consistent.
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210916025203.44841-1-cuibixuan@huawei.com
Rework irq_find_mapping() to return an both an irq_desc pointer,
optionally the virtual irq number, and rename the result to
__irq_resolve_mapping(). a new helper called irq_resolve_mapping()
is provided for code that doesn't need the virtual irq number.
irq_find_mapping() is also rewritten in terms of __irq_resolve_mapping().
Signed-off-by: Marc Zyngier <maz@kernel.org>
It is pretty odd that the radix tree uses RCU while the linear
portion doesn't, leading to potential surprises for the users,
depending on how the irqdomain has been created.
Fix this by moving the update of the linear revmap under
the mutex, and the lookup under the RCU read-side lock.
The mutex name is updated to reflect that it doesn't only
cover the radix-tree anymore.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Caching a virq number in the revmap is pretty inefficient, as
it means we will need to convert it back to either an irq_data
or irq_desc to do anything with it.
It is also a bit odd, as the radix tree does cache irq_data
pointers.
Change the revmap type to be an irq_data pointer instead of
an unsigned int, and preserve the current API for now.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Direct mappings are completely exclusive of normal mappings, meaning
that we can refactor the code slightly so that we can get rid of
the revmap_direct_max_irq field and use the revmap_size field
instead, reducing the size of the irqdomain structure.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Only a handful of old PPC systems are still using the old 'nomap'
variant of the irqdomain library. Move the associated definitions
behind a configuration option, which will allow us to make some
more radical changes.
Signed-off-by: Marc Zyngier <maz@kernel.org>
irq_linear_revmap() is supposed to be a fast path for domain
lookups, but it only exposes low-level details of the irqdomain
implementation, details which are better kept private.
The *overhead* between the two is only a function call and
a couple of tests, so it is likely that noone can show any
meaningful difference compared to the cost of taking an
interrupt.
Reimplement irq_linear_revmap() with irq_find_mapping()
in order to preserve source code compatibility, and
rename the internal field for a measure.
Signed-off-by: Marc Zyngier <maz@kernel.org>
- new driver for the Realtek Otto GPIO controller
- ACPI support for gpio-mpc8xxx
- edge event support for gpio-sch (+ Kconfig fixes)
- Kconfig improvements in gpio-ich
- fixes to older issues in gpio-mockup
- ACPI quirk for ignoring EC wakeups on Dell Venue 10 Pro 5055
- improve the GPIO aggregator code by using more generic interfaces instead of
reimplementing them in the driver
- convert the DT bindings for gpio-74x164 to yaml
- documentation improvements
- a slew of other minor fixes and improvements to GPIO drivers
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEFp3rbAvDxGAT0sefEacuoBRx13IFAmCSptQACgkQEacuoBRx
13KFDQ/+NOkRQuJarKAvGuR5LJ81CbBfH72/m9gJMB9gwNBS7g+esNWrZG/riWVM
BVs2fxlC52+ppN1rV7iMEaXSyREULrcidgoZ0H7X2vsI9MRkk/fjzpTRwbJbSLPo
C+IXBAHHfuUC1FQNtQk1cuZXl7PToHd/A14KZIkLOBxLjQddpSo7TTkv23Ub1BA7
Se13EaDrBJxzfmLR900kAKCFDyM8VRnIt7/euhmlTcXCxOg/lCbGZ4eBpEZasUs5
UA9PQX0dnnwtMER4b4TQPIdQ345A0l+xqALr8X2leqQ0AqsWQ7kveMwfSRlXI5Hr
zyuXRiA0e84h6HXIHE59kXqoa4LJVnW59hgjYx0D+fcZ5gNVnaRg/4LsztJmMd/f
uVAZazE4jd81Cr/kbtpEu5mfGPjOVBeUCeDnKtRovnaSMi24HwqvHqIauI9sM8fN
locTCYOdLfvxucAJHZ/BWe8yl301/+IlwiHiN+7+/3ljYB+HjAH42rdPwFpP1BWJ
bpgd90KxLHezeqsv83U9CTTrVK9ZM2yisVunQUo3bVi6Ztxl2Juv16P5Qs0IJW2F
mly+KNTa4M6NKCdP6luEnazmifFIsnreCzTMfPoa9w+eu/vpIw6lZDFpDAbePV+A
8XJ99TxV1Bk9kUjvKiEi2qx6uW7f5k8JIwvRvJWhRXkEzufJyUI=
=5vLN
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.13-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
- new driver for the Realtek Otto GPIO controller
- ACPI support for gpio-mpc8xxx
- edge event support for gpio-sch (+ Kconfig fixes)
- Kconfig improvements in gpio-ich
- fixes to older issues in gpio-mockup
- ACPI quirk for ignoring EC wakeups on Dell Venue 10 Pro 5055
- improve the GPIO aggregator code by using more generic interfaces
instead of reimplementing them in the driver
- convert the DT bindings for gpio-74x164 to yaml
- documentation improvements
- a slew of other minor fixes and improvements to GPIO drivers
* tag 'gpio-updates-for-v5.13-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (34 commits)
dt-bindings: gpio: add YAML description for rockchip,gpio-bank
gpio: mxs: remove useless function
dt-bindings: gpio: fairchild,74hc595: Convert to json-schema
gpio: it87: remove unused code
gpio: 104-dio-48e: Fix coding style issues
gpio: mpc8xxx: Add ACPI support
gpio: ich: Switch to be dependent on LPC_ICH
gpio: sch: Drop MFD_CORE selection
gpio: sch: depends on LPC_SCH
gpiolib: acpi: Add quirk to ignore EC wakeups on Dell Venue 10 Pro 5055
gpio: sch: Hook into ACPI GPE handler to catch GPIO edge events
gpio: sch: Add edge event support
gpio: aggregator: Replace custom get_arg() with a generic next_arg()
lib/cmdline: Export next_arg() for being used in modules
gpio: omap: Use device_get_match_data() helper
gpio: Add Realtek Otto GPIO support
dt-bindings: gpio: Binding for Realtek Otto GPIO
docs: kernel-parameters: Add gpio_mockup_named_lines
docs: kernel-parameters: Move gpio-mockup for alphabetic order
lib: bitmap: provide devm_bitmap_alloc() and devm_bitmap_zalloc()
...
Linus Walleij pointed out that ird_domain_add_simple() gained
additional functionality and can't be anymore replaced with
a simple conditional. In preparation to upgrade GPIO library
to use fwnode, introduce irq_domain_create_simple() API which is
functional equivalent to the existing irq_domain_add_simple(),
but takes a pointer to the struct fwnode_handle as a parameter.
While at it, amend documentation to mention irq_domain_create_*()
functions where it makes sense.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There's no need to keep around a dentry pointer to a simple file that
debugfs itself can look up when we need to remove it from the system.
So simplify the code by deleting the variable and cleaning up the logic
around the debugfs file.
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/YCvYV53ZdzQSWY6w@kroah.com
Core:
- Consolidation and robustness changes for irq time accounting
- Cleanup and consolidation of irq stats
- Remove the fasteoi IPI flow which has been proved useless
- Provide an interface for converting legacy interrupt mechanism into
irqdomains
Drivers:
The rare event of not having completely new chip driver code, just new
DT bindings and extensions of existing drivers to accomodate new
variants!
- Preliminary support for managed interrupts on platform devices
- Correctly identify allocation of MSIs proxyied by another device
- Generalise the Ocelot support to new SoCs
- Improve GICv4.1 vcpu entry, matching the corresponding KVM optimisation
- Work around spurious interrupts on Qualcomm PDC
- Random fixes and cleanups
Thanks,
tglx
-----BEGIN PGP SIGNATURE-----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=iytv
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Generic interrupt and irqchips subsystem updates. Unusually, there is
not a single completely new irq chip driver, just new DT bindings and
extensions of existing drivers to accomodate new variants!
Core:
- Consolidation and robustness changes for irq time accounting
- Cleanup and consolidation of irq stats
- Remove the fasteoi IPI flow which has been proved useless
- Provide an interface for converting legacy interrupt mechanism into
irqdomains
Drivers:
- Preliminary support for managed interrupts on platform devices
- Correctly identify allocation of MSIs proxyied by another device
- Generalise the Ocelot support to new SoCs
- Improve GICv4.1 vcpu entry, matching the corresponding KVM
optimisation
- Work around spurious interrupts on Qualcomm PDC
- Random fixes and cleanups"
* tag 'irq-core-2020-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
irqchip/qcom-pdc: Fix phantom irq when changing between rising/falling
driver core: platform: Add devm_platform_get_irqs_affinity()
ACPI: Drop acpi_dev_irqresource_disabled()
resource: Add irqresource_disabled()
genirq/affinity: Add irq_update_affinity_desc()
irqchip/gic-v3-its: Flag device allocation as proxied if behind a PCI bridge
irqchip/gic-v3-its: Tag ITS device as shared if allocating for a proxy device
platform-msi: Track shared domain allocation
irqchip/ti-sci-intr: Fix freeing of irqs
irqchip/ti-sci-inta: Fix printing of inta id on probe success
drivers/irqchip: Remove EZChip NPS interrupt controller
Revert "genirq: Add fasteoi IPI flow"
irqchip/hip04: Make IPIs use handle_percpu_devid_irq()
irqchip/bcm2836: Make IPIs use handle_percpu_devid_irq()
irqchip/armada-370-xp: Make IPIs use handle_percpu_devid_irq()
irqchip/gic, gic-v3: Make SGIs use handle_percpu_devid_irq()
irqchip/ocelot: Add support for Jaguar2 platforms
irqchip/ocelot: Add support for Serval platforms
irqchip/ocelot: Add support for Luton platforms
irqchip/ocelot: prepare to support more SoC
...
There is currently no way to convey the affinity of an interrupt
via irq_create_mapping(), which creates issues for devices that
expect that affinity to be managed by the kernel.
In order to sort this out, rename irq_create_mapping() to
irq_create_mapping_affinity() with an additional affinity parameter that
can be passed down to irq_domain_alloc_descs().
irq_create_mapping() is re-implemented as a wrapper around
irq_create_mapping_affinity().
No functional change.
Fixes: e75eafb9b0 ("genirq/msi: Switch to new irq spreading infrastructure")
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kurz <groug@kaod.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201126082852.1178497-2-lvivier@redhat.com
Introduce irq_domain_create_legacy() API which is functional equivalent
to the existing irq_domain_add_legacy(), but takes a pointer to the struct
fwnode_handle as a parameter.
This is useful for non OF systems.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20201030165919.86234-5-andriy.shevchenko@linux.intel.com
irqdomain.h is a user of struct fwnode_handle. Add forward declaration of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20201030165919.86234-3-andriy.shevchenko@linux.intel.com
devices which require non-PCI based MSI handling.
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which allows
to utilize the full functionality of hierarchical irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the irqdomain
which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch and
let the last few users select it.
-----BEGIN PGP SIGNATURE-----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=JlqV
-----END PGP SIGNATURE-----
Merge tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 irq updates from Thomas Gleixner:
"Surgery of the MSI interrupt handling to prepare the support of
upcoming devices which require non-PCI based MSI handling:
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which
allows to utilize the full functionality of hierarchical
irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the
irqdomain which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch
and let the last few users select it"
* tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
PCI: MSI: Fix Kconfig dependencies for PCI_MSI_ARCH_FALLBACKS
x86/apic/msi: Unbreak DMAR and HPET MSI
iommu/amd: Remove domain search for PCI/MSI
iommu/vt-d: Remove domain search for PCI/MSI[X]
x86/irq: Make most MSI ops XEN private
x86/irq: Cleanup the arch_*_msi_irqs() leftovers
PCI/MSI: Make arch_.*_msi_irq[s] fallbacks selectable
x86/pci: Set default irq domain in pcibios_add_device()
iommm/amd: Store irq domain in struct device
iommm/vt-d: Store irq domain in struct device
x86/xen: Wrap XEN MSI management into irqdomain
irqdomain/msi: Allow to override msi_domain_alloc/free_irqs()
x86/xen: Consolidate XEN-MSI init
x86/xen: Rework MSI teardown
x86/xen: Make xen_msi_init() static and rename it to xen_hvm_msi_init()
PCI/MSI: Provide pci_dev_has_special_msi_domain() helper
PCI_vmd_Mark_VMD_irqdomain_with_DOMAIN_BUS_VMD_MSI
irqdomain/msi: Provide DOMAIN_BUS_VMD_MSI
x86/irq: Initialize PCI/MSI domain at PCI init time
x86/pci: Reducde #ifdeffery in PCI init code
...
It appears that some HW is ugly enough that not all the interrupts
connected to a particular interrupt controller end up with the same
hierarchy depth (some of them are terminated early). This leaves
the irqchip hacker with only two choices, both equally bad:
- create discrete domain chains, one for each "hierarchy depth",
which is very hard to maintain
- create fake hierarchy levels for the shallow paths, leading
to all kind of problems (what are the safe hwirq values for these
fake levels?)
Implement the ability to cut short a single interrupt hierarchy
from a level marked as being disconnected by using the new
irq_domain_disconnect_hierarchy() helper.
The irqdomain allocation code will then perform the trimming
Signed-off-by: Marc Zyngier <maz@kernel.org>
PCI devices behind a VMD bus are not subject to interrupt remapping, but
the irq domain for VMD MSI cannot be distinguished from a regular PCI/MSI
irq domain.
Add a new domain bus token and allow it in the bus token check in
msi_check_reservation_mode() to keep the functionality the same once VMD
uses this token.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Link: https://lore.kernel.org/r/20200826112332.954409970@linutronix.de
irq_domain_reset_irq_data() doesn't modify the parent data, so it can be
made available even if irq domain hierarchy is not being built. We'll
subsequently use it in irq_sim code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200514083901.23445-2-brgl@bgdev.pl
This was noticed when printing debugfs for MSIs on my ARM64 server. The
new dstate IRQD_MSI_NOMASK_QUIRK came out surprisingly while it should only
be the x86 stuff for the time being...
The new MSI quirk flag uses the same bit as IRQ_DOMAIN_NAME_ALLOCATED which
is oddly defined as bit 6 for no good reason.
Switch it to the non used bit 1.
Fixes: 6f1a4891a5 ("x86/apic/msi: Plug non-maskable MSI affinity race")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200221020725.2038-1-yuzenghui@huawei.com
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when the
TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused an
infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects PCI
devices with non-maskable MSI interrupts. The problem is caused by the
non-atomic writes of the MSI address (destination APIC id) and data
(vector) fields which the device uses to construct the MSI message. The
non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after writing
address and before writing data, then the MSI block constructs a
inconsistent message which causes interrupts to be lost and subsequent
malfunction of the device.
The fix is to redirect the interrupt to the new vector on the current
CPU first and then switch it over to the new target CPU. This allows to
observe an eventually raised interrupt in the transitional stage (old
CPU, new vector) to be observed in the APIC IRR and retriggered on the
new target CPU and the new vector. The potential spurious interrupts
caused by this are harmless and can in the worst case expose a buggy
driver (all handlers have to be able to deal with spurious interrupts as
they can and do happen for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall page
which prevents resume hibernation on HYPERV guests. This change got
lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent potentially
stale IOAPIC remote IRR bits which cause stale interrupt lines after
resume.
-----BEGIN PGP SIGNATURE-----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=WxKD
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for X86:
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when
the TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused
an infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects
PCI devices with non-maskable MSI interrupts. The problem is caused
by the non-atomic writes of the MSI address (destination APIC id)
and data (vector) fields which the device uses to construct the MSI
message. The non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after
writing address and before writing data, then the MSI block
constructs a inconsistent message which causes interrupts to be
lost and subsequent malfunction of the device.
The fix is to redirect the interrupt to the new vector on the
current CPU first and then switch it over to the new target CPU.
This allows to observe an eventually raised interrupt in the
transitional stage (old CPU, new vector) to be observed in the APIC
IRR and retriggered on the new target CPU and the new vector.
The potential spurious interrupts caused by this are harmless and
can in the worst case expose a buggy driver (all handlers have to
be able to deal with spurious interrupts as they can and do happen
for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall
page which prevents resume hibernation on HYPERV guests. This
change got lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent
potentially stale IOAPIC remote IRR bits which cause stale
interrupt lines after resume"
* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Mask IOAPIC entries when disabling the local APIC
x86/hyperv: Suspend/resume the hypercall page for hibernation
x86/apic/msi: Plug non-maskable MSI affinity race
x86/boot: Handle malformed SRAT tables during early ACPI parsing
x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
Evan tracked down a subtle race between the update of the MSI message and
the device raising an interrupt internally on PCI devices which do not
support MSI masking. The update of the MSI message is non-atomic and
consists of either 2 or 3 sequential 32bit wide writes to the PCI config
space.
- Write address low 32bits
- Write address high 32bits (If supported by device)
- Write data
When an interrupt is migrated then both address and data might change, so
the kernel attempts to mask the MSI interrupt first. But for MSI masking is
optional, so there exist devices which do not provide it. That means that
if the device raises an interrupt internally between the writes then a MSI
message is sent built from half updated state.
On x86 this can lead to spurious interrupts on the wrong interrupt
vector when the affinity setting changes both address and data. As a
consequence the device interrupt can be lost causing the device to
become stuck or malfunctioning.
Evan tried to handle that by disabling MSI accross an MSI message
update. That's not feasible because disabling MSI has issues on its own:
If MSI is disabled the PCI device is routing an interrupt to the legacy
INTx mechanism. The INTx delivery can be disabled, but the disablement is
not working on all devices.
Some devices lose interrupts when both MSI and INTx delivery are disabled.
Another way to solve this would be to enforce the allocation of the same
vector on all CPUs in the system for this kind of screwed devices. That
could be done, but it would bring back the vector space exhaustion problems
which got solved a few years ago.
Fortunately the high address (if supported by the device) is only relevant
when X2APIC is enabled which implies interrupt remapping. In the interrupt
remapping case the affinity setting is happening at the interrupt remapping
unit and the PCI MSI message is programmed only once when the PCI device is
initialized.
That makes it possible to solve it with a two step update:
1) Target the MSI msg to the new vector on the current target CPU
2) Target the MSI msg to the new vector on the new target CPU
In both cases writing the MSI message is only changing a single 32bit word
which prevents the issue of inconsistency.
After writing the final destination it is necessary to check whether the
device issued an interrupt while the intermediate state #1 (new vector,
current CPU) was in effect.
This is possible because the affinity change is always happening on the
current target CPU. The code runs with interrupts disabled, so the
interrupt can be detected by checking the IRR of the local APIC. If the
vector is pending in the IRR then the interrupt is retriggered on the new
target CPU by sending an IPI for the associated vector on the target CPU.
This can cause spurious interrupts on both the local and the new target
CPU.
1) If the new vector is not in use on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then interrupt entry code will
ignore that spurious interrupt. The vector is marked so that the
'No irq handler for vector' warning is supressed once.
2) If the new vector is in use already on the local CPU then the IRR check
might see an pending interrupt from the device which is using this
vector. The IPI to the new target CPU will then invoke the handler of
the device, which got the affinity change, even if that device did not
issue an interrupt
3) If the new vector is in use already on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then the handler of the device which
uses that vector on the local CPU will be invoked.
expose issues in device driver interrupt handlers which are not prepared to
handle a spurious interrupt correctly. This not a regression, it's just
exposing something which was already broken as spurious interrupts can
happen for a lot of reasons and all driver handlers need to be able to deal
with them.
Reported-by: Evan Green <evgreen@chromium.org>
Debugged-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Evan Green <evgreen@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87imkr4s7n.fsf@nanos.tec.linutronix.de
A single controller can handle normal interrupts and wake-up interrupts
independently, with a different numbering space. It is thus crucial to
allow the driver for such a controller discriminate between the two.
A simple way to do so is to tag the wake-up irqdomain with a "bus token"
that indicates the wake-up domain. This slightly abuses the notion of
bus, but also radically simplifies the design of such a driver. Between
two evils, we choose the least damaging.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-2-git-send-email-ilina@codeaurora.org
Booting a large arm64 server (HiSi D05) leads to the following
shouting at boot time:
[ 20.722132] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.730851] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.739560] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.748267] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.756975] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.765683] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
[ 20.774391] debugfs: File 'irqchip@(____ptrval____)-3' in directory 'domains' already present!
and many more... Evidently, we expect something a bit more informative
than ____ptrval____, and certainly we want all of our domains, not just
the first one.
For that, turn the %p used to generate the fwnode name into something
that won't be repainted (%pa). Given that we've now fixed all users to
pass a pointer to a PA, it will actually do the right thing.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
With the system coprocessor managing the range allocation of the
inputs to Interrupt Aggregator, it is difficult to represent
the device IRQs from DT.
The suggestion is to use MSI in such cases where devices wants
to allocate and group interrupts dynamically.
Create a MSI domain bus layer that allocates and frees MSIs for
a device.
APIs that are implemented:
- ti_sci_inta_msi_create_irq_domain() that creates a MSI domain
- ti_sci_inta_msi_domain_alloc_irqs() that creates MSIs for the
specified device and resource.
- ti_sci_inta_msi_domain_free_irqs() frees the irqs attached to the device.
- ti_sci_inta_msi_get_virq() for getting the virq attached to a specific event.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Core changes:
- The big change this time around is the irqchip handling in
the qualcomm pin controllers, closely coupled with the
gpiochip. This rework, in a classic fall-between-the-chairs
fashion has been sidestepped for too long. The Qualcomm
IRQchips using the SPMI and SSBI transport mechanisms have
been rewritten to use hierarchical irqchip. This creates
the base from which I intend to gradually pull support for
hierarchical irqchips into the gpiolib irqchip helpers to
cut down on duplicate code. We have too many hacks in the
kernel because people have been working around the missing
hierarchical irqchip for years, and once it was there,
noone understood it for a while. We are now slowly adapting
to using it. This is why this pull requests include changes
to MFD, SPMI, IRQchip core and some ARM Device Trees
pertaining to the Qualcomm chip family. Since Qualcomm have
so many chips and such large deployments it is paramount
that this platform gets this right, and now it (hopefully)
does.
- Core support for pull-up and pull-down configuration, also
from the device tree. When a simple GPIO chip support a
"off or on" pull-up or pull-down resistor, we provide a
way to set this up using machine descriptors or device tree.
If more elaborate control of pull up/down (such as
resistance shunt setting) is required, drivers should be
phased over to use pin control. We do not yet provide a
userspace ABI for this pull up-down setting but I suspect
the makers are going to ask for it soon enough. PCA953x
is the first user of this new API.
- The GPIO mockup driver has been revamped after some
discussion improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for
both testing and virtual prototyping, e.g. when you do
not yet have a GPIO expander to play with but really
want to get something to develop code around before
hardware is available. It's neat. The blackbox testing
usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating
flags.
- A new device core helper for devm_platform_ioremap_resource()
is funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped
I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum
driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers.
-----BEGIN PGP SIGNATURE-----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=VoVC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in the
qualcomm pin controllers, closely coupled with the gpiochip. This
rework, in a classic fall-between-the-chairs fashion has been
sidestepped for too long.
The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
have been rewritten to use hierarchical irqchip. This creates the
base from which I intend to gradually pull support for hierarchical
irqchips into the gpiolib irqchip helpers to cut down on duplicate
code.
We have too many hacks in the kernel because people have been
working around the missing hierarchical irqchip for years, and once
it was there, noone understood it for a while. We are now slowly
adapting to using it.
This is why this pull requests include changes to MFD, SPMI,
IRQchip core and some ARM Device Trees pertaining to the Qualcomm
chip family. Since Qualcomm have so many chips and such large
deployments it is paramount that this platform gets this right, and
now it (hopefully) does.
- Core support for pull-up and pull-down configuration, also from the
device tree. When a simple GPIO chip supports an "off or on" pull-up
or pull-down resistor, we provide a way to set this up using
machine descriptors or device tree.
If more elaborate control of pull up/down (such as resistance shunt
setting) is required, drivers should be phased over to use pin
control. We do not yet provide a userspace ABI for this pull
up-down setting but I suspect the makers are going to ask for it
soon enough. PCA953x is the first user of this new API.
- The GPIO mockup driver has been revamped after some discussion
improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for both testing
and virtual prototyping, e.g. when you do not yet have a GPIO
expander to play with but really want to get something to develop
code around before hardware is available. It's neat. The blackbox
testing usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating flags.
- A new device core helper for devm_platform_ioremap_resource() is
funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers"
* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
gpio: gpio-omap: fix level interrupt idling
gpio: amd-fch: Set proper output level for direction_output
x86: apuv2: remove unused variable
gpio: pca953x: Use PCA_LATCH_INT
platform/x86: fix PCENGINES_APU2 Kconfig warning
gpio: pca953x: Fix dereference of irq data in shutdown
gpio: amd-fch: Fix type error found by sparse
gpio: amd-fch: Drop const from resource
gpio: mxc: add check to return defer probe if clock tree NOT ready
gpio: ftgpio: Register per-instance irqchip
gpio: ixp4xx: Add DT bindings
x86: pcengines apuv2 gpio/leds/keys platform driver
gpio: AMD G-Series PCH gpio driver
drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
gpio: tqmx86: Set proper output level for direction_output
gpio: sprd: Change to use SoC compatible string
gpio: sprd: Use SoC compatible string instead of wildcard string
gpio: of: Handle both enable-gpio{,s}
gpio: of: Restrict enable-gpio quirk to regulator-gpio
gpio: davinci: use devm_platform_ioremap_resource()
...
The default irq domain allows legacy code to create irqdomain
mappings without having to track the domain it is allocating
from. Setting the default domain is a one shot, fire and forget
operation, and no effort was made to be able to retrieve this
information at a later point in time.
Newer irqdomain APIs (the hierarchical stuff) relies on both
the irqchip code to track the irqdomain it is allocating from,
as well as some form of firmware abstraction to easily identify
which piece of HW maps to which irq domain (DT, ACPI).
For systems without such firmware (or legacy platform that are
getting dragged into the 21st century), things are a bit harder.
For these cases (and these cases only!), let's provide a way
to retrieve the default domain, allowing the use of the v2 API
without having to resort to platform-specific hacks.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a new function irq_domain_translate_twocell() that is to be used as
the translate function in struct irq_domain_ops for the v2 IRQ API.
This patch also changes irq_domain_xlate_twocell() from the v1 IRQ API
to call irq_domain_translate_twocell() in the v2 IRQ API. This required
changes to of_phandle_args_to_fwspec()'s arguments so that it can be
called from multiple places.
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt affinity management uses straight cpumask pointers to convey
the automatically assigned affinity masks for managed interrupts. The core
interrupt descriptor allocation also decides based on the pointer being non
NULL whether an interrupt is managed or not.
Devices which use managed interrupts usually have two classes of
interrupts:
- Interrupts for multiple device queues
- Interrupts for general device management
Currently both classes are treated the same way, i.e. as managed
interrupts. The general interrupts get the default affinity mask assigned
while the device queue interrupts are spread out over the possible CPUs.
Treating the general interrupts as managed is both a limitation and under
certain circumstances a bug. Assume the following situation:
default_irq_affinity = 4..7
So if CPUs 4-7 are offlined, then the core code will shut down the device
management interrupts because the last CPU in their affinity mask went
offline.
It's also a limitation because it's desired to allow manual placement of
the general device interrupts for various reasons. If they are marked
managed then the interrupt affinity setting from both user and kernel space
is disabled.
To remedy that situation it's required to convey more information than the
cpumasks through various interfaces related to interrupt descriptor
allocation.
Instead of adding yet another argument, create a new data structure
'irq_affinity_desc' which for now just contains the cpumask. This struct
can be expanded to convey auxilliary information in the next step.
No functional change, just preparatory work.
[ tglx: Simplified logic and clarified changelog ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dou Liyang <douliyangs@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: kashyap.desai@broadcom.com
Cc: shivasharan.srikanteshwara@broadcom.com
Cc: sumit.saxena@broadcom.com
Cc: ming.lei@redhat.com
Cc: hch@lst.de
Cc: douliyang1@huawei.com
Link: https://lkml.kernel.org/r/20181204155122.6327-2-douliyangs@gmail.com
This is a cascaded interrupt controller in the AP806 GIC that collapses
SEIs (System Error Interrupt) coming from the AP and the CPs (through
the ICU).
The SEI handles up to 64 interrupts. The first 21 interrupts are wired
from the AP. The next 43 interrupts are from the CPs and are triggered
through MSI messages. To handle this complexity, the driver has to
declare to the upper layer: one IRQ domain for the wired interrupts,
one IRQ domain for the MSIs; and acts as a MSI controller ('parent')
by declaring an MSI domain.
Suggested-by: Haim Boot <hayim@marvell.com>
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
At the beginning of times, irq_find_host() was simple. Each device node
implemented at most one irq domain, and we were happy. Over time, things
have become more complex, and we now have nodes implementing a plurality
of domains, tagged by "bus_token".
Crutially, users of irq_find_host() all expect the most basic domain
to be returned, and not any other domain such as a bus-specific MSI
domain.
So let's change irq_find_host() to first look for a DOMAIN_BUS_WIRED
domain, and only if this fails fallback to DOMAIN_BUS_ANY. Note that
this is consistent with what irq_create_fwspec_mapping is already
doing, see 530cbe100e ("irqdomain: Allow domain lookup with
DOMAIN_BUS_WIRED token").
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20180508121438.11301-6-marc.zyngier@arm.com
The 'early' argument of irq_domain_activate_irq() is actually used to
denote reservation mode. To avoid confusion, rename it before abuse
happens.
No functional change.
Fixes: 7249164346 ("genirq/irqdomain: Update irq_domain_ops.activate() signature")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
Commit:
f110711a60 ("irqdomain: Convert irqdomain-%3Eof_node to fwnode")
converted of_node field to fwnode, but didn't update its comments.
Update it.
Fixes: f110711a60 ("irqdomain: Convert irqdomain-%3Eof_node to fwnode")
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The revmap_trees_mutex protects domain->revmap_tree. There is no
need to make it global because it is allowed to modify revmap_tree
of two different domains concurrently. Having said that, this would
not be a actual bottleneck because the interrupt map/unmap does not
occur quite often. Rather, the motivation is to tidy up the code
from a data structure point of view.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Propagate the early activation mode to the irqdomain activate()
callbacks. This is required for the upcoming reservation, late vector
assignment scheme, so that the early activation call can act accordingly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.028353660@linutronix.de
Allow irq_domain_activate_irq() to fail. This is required to support a
reservation and late vector assignment scheme.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.933882227@linutronix.de
The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.
The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:
- A return value, so activation can fail at request_irq() time
- Information that the activate invocation is early, i.e. before
request_irq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.848490816@linutronix.de
In the !IRQ_DOMAIN_HIERARCHY cas the activation stubs are not
setting/clearing the activation status bits. This is not a problem at the
moment, but upcoming changes require a correct status.
Add the set/clear incovations to the stub functions and move them to the
core internal header to avoid duplication and visibility outside the core.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.591985591@linutronix.de
Marc Zyngier