Correct headphone detection for 1st generation iMac G3 Slot-loading (Screamer).
This patch fixes the regression in the recent snd-powermac which
doesn't support some G3/G4 PowerMacs:
http://lkml.org/lkml/2008/10/1/220
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add mixer controls for PowerMac G4 AGP (Screamer).
This patch fixes the regression in the recent snd-powermac which
doesn't support some G3/G4 PowerMacs:
http://lkml.org/lkml/2008/10/1/220
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rob Sims wrote:
"I can't seem to turn on register 0x17, bit 3 in the sound chip, except
by codec_reg_write; the mixer lacks direct or indirect control. It
seems there are two names for the output of the rec mixer:
Capture ST Mixer
Playback Mixer
Would the following do the trick?"
I confirm that this solves the audio problems I was having.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 00c5372d37 caused the MPC8544DS
board to hang at boot. The MPC8544DS is unique in that it doesn't use
the PCI slots on the ULI (unlike the MPC8572DS or MPC8610HPCD). So
the dummy read at the end of the address space causes us to hang.
We can detect the situation by comparing the bridge's BARs versus
the root complex.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Set the hardware to ignore all write/erase cycles to the GbE region in
the ICHx NVM. This feature can be disabled by the WriteProtectNVM module
parameter (enabled by default) only after a hardware reset, but
the machine must be power cycled before trying to enable writes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: arjan@linux.intel.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a build error in the pxa2xx-spi driver,
introduced by commit 7e96445533
("pxa2xx_spi: dma bugfixes")
CC drivers/spi/pxa2xx_spi.o
drivers/spi/pxa2xx_spi.c: In function 'map_dma_buffers':
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c: In function 'pump_transfers':
drivers/spi/pxa2xx_spi.c:897: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'unsigned int'
[dbrownell@users.sourceforge.net: fix warning too ]
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the IRQ handling on the MN10300 arch.
This patch makes a number of significant changes:
(1) It separates the irq_chip definition for edge-triggered interrupts from
the one for level-triggered interrupts.
This is necessary because the MN10300 PIC latches the IRQ channel's
interrupt request bit (GxICR_REQUEST), even after the device has ceased to
assert its interrupt line and the interrupt channel has been disabled in
the PIC. So for level-triggered interrupts we need to clear this bit when
we re-enable - which is achieved by setting GxICR_DETECT but not
GxICR_REQUEST when writing to the register.
Not doing this results in spurious interrupts occurring because calling
mask_ack() at the start of handle_level_irq() is insufficient - it fails
to clear the REQUEST latch because the device that caused the interrupt is
still asserting its interrupt line at this point.
(2) IRQ disablement [irq_chip::disable_irq()] shouldn't clear the interrupt
request flag for edge-triggered interrupts lest it lose an interrupt.
(3) IRQ unmasking [irq_chip::unmask_irq()] also shouldn't clear the interrupt
request flag for edge-triggered interrupts lest it lose an interrupt.
(4) The end() operation is now left to the default (no-operation) as
__do_IRQ() is compiled out. This may affect misrouted_irq(), but
according to Thomas Gleixner it's the correct thing to do.
(5) handle_level_irq() is used for edge-triggered interrupts rather than
handle_edge_irq() as the MN10300 PIC latches interrupt events even on
masked IRQ channels, thus rendering IRQ_PENDING unnecessary. It is
sufficient to call mask_ack() at the start and unmask() at the end.
(6) For level-triggered interrupts, ack() is now NULL as it's not used, and
there is no effective ACK function on the PIC. mask_ack() is now the
same as mask() as the latch continues to latch, even when the channel is
masked.
Further, the patch discards the disable() op implementation as its now the same
as the mask() op implementation, which is used instead.
It also discards the enable() op implementations as they're now the same as
the unmask() op implementations, which are used instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm mpath: add missing path switching locking
dm: cope with access beyond end of device in dm_merge_bvec
dm: always allow one page in dm_merge_bvec
Moving the path activation to workqueue along with scsi_dh patches introduced
a race. It is due to the fact that the current_pgpath (in the multipath data
structure) can be modified if changes happen in any of the paths leading to
the lun. If the changes lead to current_pgpath being set to NULL, then it
leads to the invalid access which results in the panic below.
This patch fixes that by storing the pgpath to activate in the multipath data
structure and properly protecting it.
Note that if activate_path is called twice in succession with different pgpath,
with the second one being called before the first one is done, then activate
path will be called twice for the second pgpath, which is fine.
Unable to handle kernel paging request for data at address 0x00000020
Faulting instruction address: 0xd000000000aa1844
cpu 0x1: Vector: 300 (Data Access) at [c00000006b987a80]
pc: d000000000aa1844: .activate_path+0x30/0x218 [dm_multipath]
lr: c000000000087a2c: .run_workqueue+0x114/0x204
sp: c00000006b987d00
msr: 8000000000009032
dar: 20
dsisr: 40000000
current = 0xc0000000676bb3f0
paca = 0xc0000000006f3680
pid = 2528, comm = kmpath_handlerd
enter ? for help
[c00000006b987da0] c000000000087a2c .run_workqueue+0x114/0x204
[c00000006b987e40] c000000000088b58 .worker_thread+0x120/0x144
[c00000006b987f00] c00000000008ca70 .kthread+0x78/0xc4
[c00000006b987f90] c000000000027cc8 .kernel_thread+0x4c/0x68
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If for any reason dm_merge_bvec() is given an offset beyond the end of the
device, avoid an oops and always allow one page to be added to an empty bio.
We'll reject the I/O later after the bio is submitted.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Some callers assume they can always add at least one page to an empty bio,
so dm_merge_bvec should not return 0 in this case: we'll reject the I/O
later after the bio is submitted.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a xfrm_{state,policy}_walk leak if pfkey socket is closed while
dumping is on-going.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following actions are possible:
tcp_v6_rcv
skb->dev = NULL;
tcp_v6_do_rcv
tcp_v6_hnd_req
tcp_check_req
req->rsk_ops->send_ack == tcp_v6_send_ack
So, skb->dev can be NULL in tcp_v6_send_ack. We must obtain namespace
from dst entry.
Thanks to Vitaliy Gusev <vgusev@openvz.org> for initial problem finding
in IPv4 code.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one took a long time to rear up because LDT usage is not very
common, but the bug is quite serious. It got introduced along with
another bug, already fixed, by 75b8bb3e56
After investigating a JRE failure, I found this bug was introduced a long time
ago, and had already managed to survive another bugfix which occurred on the
same line. The result is a total failure of the JRE due to LDT selectors not
working properly.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Glauber de Oliveira Costa <gcosta@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After investigating a JRE failure, I found this bug was introduced a
long time ago, and had already managed to survive another bugfix which
occurred on the same line. The result is a total failure of the JRE due
to LDT selectors not working properly.
This one took a long time to rear up because LDT usage is not very
common, but the bug is quite serious. It got introduced along with
another bug, already fixed, by 75b8bb3e56
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Glauber de Oliveira Costa <gcosta@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix failure to shutdown with CPU hotplug
powerpc: Fix PCI in Holly device tree
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimer: prevent migration of per CPU hrtimers
hrtimer: mark migration state
hrtimer: fix migration of CB_IRQSAFE_NO_SOFTIRQ hrtimers
hrtimer: migrate pending list on cpu offline
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Since call to function sctp_sf_abort_violation() need paramter 'arg' with
'struct sctp_chunk' type, it will read the chunk type and chunk length from
the chunk_hdr member of chunk. But call to sctp_sf_violation_paramlen()
always with 'struct sctp_paramhdr' type's parameter, it will be passed to
sctp_sf_abort_violation(). This may cause kernel panic.
sctp_sf_violation_paramlen()
|-- sctp_sf_abort_violation()
|-- sctp_make_abort_violation()
This patch fixed this problem. This patch also fix two place which called
sctp_sf_violation_paramlen() with wrong paramter type.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dell Inspiron 1525 seems to have a buggy BIOS setup and screws up
the recent codec parser, as reported by Oleksandr Natalenko:
http://lkml.org/lkml/2008/9/12/203
This patch adds the working model, dell-3stack, statically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
The error path in cs4270_probe/cs4270_remove is pretty broken:
* If cs4270_probe fails, codec is leaked.
* If snd_soc_register_card fails, cs4270_i2c_driver stays registered.
* If I2C support is enabled but no I2C device is found, i2c_del_driver
is never called (neither in cs4270_probe nor in cs4270_remove.
Fix all 3 problems by implementing a clean error path in cs4270_probe
and jumping to its labels as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We're never supposed to shrink the headroom or tailroom. In fact,
shrinking the headroom is a fatal action.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tracked down the shutdown regression to CPUs not dying
when being shut down during power-off. This turns out to
be due to the system_state being SYSTEM_POWER_OFF, which
this code doesn't take as a valid state for shutting off
CPUs in.
This has never made sense to me, but when I added hotplug
code to implement hibernate I only "made it work" and did
not question the need to check the system_state. Thomas
Gleixner helped me dig, but the only thing we found is
that it was added with the original commit that added CPU
hotplug support.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI bridge on the Holly board is incorrectly represented in the
device tree. The current device tree node for the PCI bridge sits
under the tsi-bridge node. That's not obviously wrong, but the PCI
bridge translates some PCI spaces into CPU address ranges which were
not translated by the "ranges" property in tsi-bridge node.
We used to get away with this problem because the PCI bridge discovery
code was also buggy, assuming incorrectly that PCI host bridge nodes
were always directly under the root bus and treating the translated
addresses as raw CPU addresses, rather than parent bus addresses.
This has since been fixed, thus breaking Holly.
This could be fixed by adding extra translations to the tsi-bridge
node, but this patch instead moves the Holly PCI bridge out of the
tsi-bridge node to the root bus. This makes the tsi-bridge node
represent only the built-in IO devices in the bridge, with a
more-or-less contiguous address range. This is the same convention
used on Freescale SoC chips, where the "soc" node represents only the
IMMR region, and the PCI and other bus bridges are separate nodes
under the root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Initial fix for making sure that we can access percpu variables
in all C code (commit: 10617bbe84)
inadvertantly allocated the memory in the "percpu" section of
the vmlinux ELF executable. This confused kexec/dump.
Signed-off-by: Tony Luck <tony.luck@intel.com>
There's a race between mm->owner assignment and swapoff, more easily
seen when task slab poisoning is turned on. The condition occurs when
try_to_unuse() runs in parallel with an exiting task. A similar race
can occur with callers of get_task_mm(), such as /proc/<pid>/<mmstats>
or ptrace or page migration.
CPU0 CPU1
try_to_unuse
looks at mm = task0->mm
increments mm->mm_users
task 0 exits
mm->owner needs to be updated, but no
new owner is found (mm_users > 1, but
no other task has task->mm = task0->mm)
mm_update_next_owner() leaves
mmput(mm) decrements mm->mm_users
task0 freed
dereferencing mm->owner fails
The fix is to notify the subsystem via mm_owner_changed callback(),
if no new owner is found, by specifying the new task as NULL.
Jiri Slaby:
mm->owner was set to NULL prior to calling cgroup_mm_owner_callbacks(), but
must be set after that, so as not to pass NULL as old owner causing oops.
Daisuke Nishimura:
mm_update_next_owner() may set mm->owner to NULL, but mem_cgroup_from_task()
and its callers need to take account of this situation to avoid oops.
Hugh Dickins:
Lockdep warning and hang below exec_mmap() when testing these patches.
exit_mm() up_reads mmap_sem before calling mm_update_next_owner(),
so exec_mmap() now needs to do the same. And with that repositioning,
there's now no point in mm_need_new_owner() allowing for NULL mm.
Reported-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
cdrom: update ioctl documentation
ide: note that IDE generic may prevent other drivers from attaching
ide-tape: fix vendor strings
Swarm: Fix crash due to missing initialization
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[SSB] Initialise dma_mask for SSB_BUSTYPE_SSB devices
[MIPS] BCM47xx: Fix build error due to missing PCI functions
[MIPS] IP27: Switch to dynamic interrupt routing avoding panic on error.
[MIPS] au1000: Make sure GPIO value is zero or one
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdboc,tty: Fix tty polling search to use name correctly
kgdb, x86_64: fix PS CS SS registers in gdb serial
kgdb, x86_64: gdb serial has BX and DX reversed
kgdb, x86, arm, mips, powerpc: ignore user space single stepping
kgdb: could not write to the last of valid memory with kgdb
Impact: per CPU hrtimers can be migrated from a dead CPU
The hrtimer code has no knowledge about per CPU timers, but we need to
prevent the migration of such timers and warn when such a timer is
active at migration time.
Explicitely mark the timers as per CPU and use a more understandable
mode descriptor for the interrupts safe unlocked callback mode, which
is used by hrtimer_sleeper and the scheduler code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: during migration active hrtimers can be seen as inactive
The migration code removes the hrtimers from the queues of the dead
CPU and sets the state temporary to INACTIVE. The enqueue code sets it
to ACTIVE/PENDING again.
Prevent that the wrong state can be seen by using a separate migration
state bit.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: Stale timers after a CPU went offline.
commit 37bb6cb409
hrtimer: unlock hrtimer_wakeup
changed the hrtimer sleeper callback mode to CB_IRQSAFE_NO_SOFTIRQ due
to locking problems. A result of this change is that when enqueue is
called for an already expired hrtimer the callback function is not
longer called directly from the enqueue code. The normal callers have
been fixed in the code, but the migration code which moves hrtimers
from a dead CPU to a live CPU was not made aware of this.
This can be fixed by checking the timer state after the call to
enqueue in the migration code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: hrtimers which are on the pending list are not migrated at cpu
offline and can be stale forever
Add the pending list migration when CONFIG_HIGH_RES_TIMERS is enabled
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ASoC: Fix another cs4270 error path
ALSA: make the CS4270 driver a new-style I2C driver
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] qlogicpti: fix sg list traversal error in continuation entries
[SCSI] Fix hang with split requests
[SCSI] qla2xxx: Defer enablement of RISC interrupts until ISP initialization completes.
Takashi Iwai