If a receive is in progress or starts before the transmit has
a chance, then lower the Signal Free Time of the upcoming transmit
to no more than CEC_SIGNAL_FREE_TIME_NEW_INITIATOR.
This is per the specification requirements.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The calculation of the Signal Free Time in the framework was not
correct. If a message was received, then the next transmit should be
considered a New Initiator and use a shorter SFT value.
This was not done with the result that if both sides where continually
sending messages, they both could use the same SFT value and one side
could deny the other side access to the bus.
Note that this fix does not take the corner case into account where
a receive is in progress when you call adap_transmit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When there is no EDID the CEC adapter should be unconfigured as
well. So call cec_phys_addr_invalidate() when this happens.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When there is no EDID the CEC adapter should be unconfigured as
well. So call cec_phys_addr_invalidate() when this happens.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the HDMI cable is disconnected or the CEC adapter is manually
unconfigured, then all pending transmits and wait-for-replies are
aborted. Signal this with new status bits (CEC_RX/TX_STATUS_ABORTED).
If due to (usually) a driver bug a transmit never ends (i.e. the
transmit_done was never called by the driver), then when this times
out the message is marked with CEC_TX_STATUS_TIMEOUT.
This should not happen and is an indication of a driver bug.
Without a separate status bit for this it was impossible to detect
this from userspace.
The 'transmit timed out' kernel message is now a warning, so this
should be more prominent in the kernel log as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clarify that calling cec_transmit_done can start a new transmit and
that you should put the hardware in a state that allows for a new
transmit before calling this function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As pointed at:
https://bugzilla.kernel.org/show_bug.cgi?id=199323
This patch causes a bad effect on RPi. I suspect that the root
cause is at the USB out of tree RPi driver, with uses high priority
interrupts instead of normal ones. Anyway, as this patch
is mostly a cleanup, better to revert it.
This reverts commit 7d95fb746c.
Cc: stable@vger.kernel.org # For Kernel 4.18
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Changing framerate right before streamon had no effect,
the new framerate value was taken into account only at
next streamon, fix this.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the "xclk" clock was added, it was made mandatory. This broke the
driver on an OLPC plaform which doesn't know such clock. Make it
optional.
Tested on a OLPC XO-1 laptop.
Fixes: 0a024d634c ("[media] ov7670: get xclk")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The regmap change causes multiple warnings like
drivers/media/i2c/ov9650.c: In function 'ov965x_g_volatile_ctrl':
drivers/media/i2c/ov9650.c:889:29: error: 'reg2' may be used uninitialized in this function [-Werror=maybe-uninitialized]
exposure = ((reg2 & 0x3f) << 10) | (reg1 << 2) |
~~~~~~~~~~~~~~~^~~~~~
It is apparently hard for the compiler to see here if ov965x_read()
returned successfully or not. Besides, we have a v4l2_dbg() statement
that prints an uninitialized value if regmap_read() fails.
Adding an 'else' clause avoids the ambiguity.
Fixes: 361f3803ad ("media: ov9650: use SCCB regmap")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Function alignments are off by 1 space, as reported by
checkpatch.pl --strict.
Fix those.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a v4l2 sub-device driver for the Sony imx355 image sensor.
This is a camera sensor using the i2c bus for control and the
csi-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- 4 test patterns control support
- vflip/hflip control support (will impact the output bayer order)
- support following resolutions:
- 3268x2448, 3264x2448, 3280x2464 @ 30fps
- 1940x1096, 1936x1096, 1924x1080, 1920x1080 @ 60fps
- 1640x1232, 1640x922, 1300x736, 1296x736,
1284x720, 1280x720 820x616 @ 120fps
- support 4 bayer orders output (via change v/hflip)
- SRGGB10(default), SGRBG10, SGBRG10, SBGGR10
[Sakari Ailus: Use do_div() for dividing 64-bit numbers, fix fwnode if usage]
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Function alignments are off by 1 space, as reported by
checkpatch.pl --strict.
Fix those.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a v4l2 sub-device driver for the Sony imx319 image sensor.
This is a camera sensor using the i2c bus for control and the
csi-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- 4 test patterns control support
- vflip/hflip control support (will impact the output bayer order)
- support following resolutions:
- 3264x2448, 3280x2464 @ 30fps
- 1936x1096, 1920x1080 @ 60fps
- 1640x1232, 1640x922, 1296x736, 1280x720 @ 120fps
- support 4 bayer orders output (via change v/hflip)
- SRGGB10(default), SGRBG10, SGBRG10, SBGGR10
[Sakari Ailus: Replace 64-bit division by do_div(), fix fwnode if usage]
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sometimes it may be necessary to grab a control while holding the control
handler's lock. Provide an unlocked variant of v4l2_ctrl_grab for the
purpose --- it's called __v4l2_ctrl_grab.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_ctrl_grab() is documented in the header; there's no need to have a
comment explaining what the function does in the .c file.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver for the dw9807 voice coil was renamed as dw9807-vcm.c to
reflect the fact that the chip also contains an EEPROM. While there is no
EEPROM (nor MFD) driver yet and it may not be ever even needed, the driver
was renamed accordingly. But the MAINTAINERS entry was not. Fix this.
Fixes: e6c17ada31 ("media: dw9807-vcm: Recognise this is just the VCM bit of the device")
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commits 03fbdb2fc2 ("media: move videobuf2 to drivers/media/common")
and 7952be9b6e ("media: drivers/media/common/videobuf2: rename from
videobuf") moved videobuf2 framework source code finally to
drivers/media/common/videobuf2 directory, so update relevant paths in
MAINTAINERS file.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is no need to create another input device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is no need to create another input device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
libevdev (which is used by libinput) gets a list of keycodes from the
input device on creation. Any events with keycodes which are not in this
list are silently dropped. So, set all keycodes on device creation since
we do not know which will be used if the keymap changes.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_fwnode_reference_parse_int_props() has a big name, causing
it to cause coding style warnings. Also, it depends on a const
struct embedded indide a function.
Rearrange the logic in order to move the struct declaration out
of such function and use it inside this function.
That cleans up some coding style issues.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is already a typedef for the parse endpoint function.
However, instead of using it, it is redefined at the C file
(and on one of the function headers).
Replace them by the function typedef, in order to cleanup
several related coding style warnings.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are several coding style issues at those definitions,
and the previous patchset added even more.
Address the trivial ones by first calling:
./scripts/checkpatch.pl --strict --fix-inline include/media/v4l2-async.h include/media/v4l2-fwnode.h include/media/v4l2-mediabus.h drivers/media/v4l2-core/v4l2-async.c drivers/media/v4l2-core/v4l2-fwnode.c
and then manually adjusting the style where needed.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the v4l2-fwnode now allows drivers to set defaults, and eventually
override them by specifying properties in DTS, use defaults for the CEU
driver.
Also remove endpoint properties from the gr-peach-audiocamerashield as
they match the defaults now specified in the driver code
(h/vsync-active and bus-width) or are not relevant to the interface
as they cannot be configured (pclk-sample).
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the v4l2-fwnode framework now allows specifying defaults configurations,
expand the description of the optional endpoint properties for the CEU
interface to better explain which are their defaults values.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Refer to video-interfaces.txt when describing standard properties.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of opportunistically trying to gather some information from the
V4L2 endpoint, set the bus type and let the V4L2 fwnode framework figure
out the configuration.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The semantics of v4l2_fwnode_endpoint_parse() and
v4l2_fwnode_endpoint_alloc_parse() have changed slightly: they now take
the bus type from the user as well as a default configuration for the bus
that shall reflect the DT binding defaults. Document this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2 fwnode framework only parsed CSI-2 D-PHY endpoints while C-PHY
support wasn't there. Also parse endpoints for media bus type
V4L2_MBUS_CSI2_CPHY.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the given media bus type set by the caller. If none is given (i.e. the
mbus type is V4L2_MBUS_UNKNOWN, or 0), fall back to the old behaviour.
This is to obtain the information from the DT or try to guess the bus
type.
-ENXIO is returned if the caller sets the bus type but that does not match
with what's in DT. Also return -ENXIO if bus type detection failed to
separate this from the rest of the errors.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Print bus type either as set by the driver or as parsed from the bus-type
property, as well as the guessed V4L2 media bus type.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The caller may provide default flags for the endpoint. Change the
configuration based on what is available through the fwnode property API.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the media bus types instead of the fwnode bus types internally. This
is the interface to the drivers as well, making the use of the fwnode bus
types more localised to the V4L2 fwnode framework.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In order to prepare for allowing drivers to set the defaults for a given
bus, make zeroing the struct conditional based on detecting the bus.
All callers now set the bus type to zero which allows only zeroing the
remaining bus union.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Initialise the V4L2 fwnode endpoints to zero in all drivers using
v4l2_fwnode_endpoint_parse(). This prepares for setting default endpoint
flags as well as the bus type. Setting bus type to zero will continue to
guess the bus among the guessable set (parallel, Bt.656 and CSI-2 D-PHY).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Parsing the graph endpoint is always successful; therefore parse it as
last.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Most hardware doesn't support re-mapping of the CSI-2 lanes. Especially
sensor drivers have a default number of lanes. Instead of requiring the
caller (the driver) to provide such a unit mapping, provide one if no
mapping is configured.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make use of the default CSI-2 lane mapping from caller-passed
configuration.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Only assign endpoint configuration if the endpoint is parsed successfully.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Read the lane inversion independently of whether the "data-lanes" property
exists. This makes sense since the caller may pass the number of lanes as
the default configuration while the lane inversion configuration may still
be available in firmware.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case the device supports multiple video bus types on an endpoint, the
V4L2 fwnode framework attempts to detect the type based on the available
information. This wasn't working really well, and sometimes could lead to
the V4L2 fwnode endpoint struct as being mishandled between the bus types.
Default to Bt.656 if no properties suggesting a bus type are found.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of allocating the V4L2 fwnode endpoint in
v4l2_fwnode_endpoint_alloc_parse, let the caller to do this. This allows
setting default parameters for the endpoint which is a very common need
for drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI-2 bus may use either D-PHY or C-PHY. Make this visible in media
bus enum.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Allow specifying the bus type explicitly for MIPI D-PHY, parallel and
Bt.656 busses. This is useful for devices that can make use of different
bus types. There are CSI-2 transmitters and receivers but the PHY
selection needs to be made between C-PHY and D-PHY; many devices also
support parallel and Bt.656 interfaces but the means to pass that
information to software wasn't there.
Autodetection (value 0) is removed as an option as the property could be
simply omitted in that case.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The continuous clock flag was only set if there was a clock or data lanes.
This isn't needed as such a configuration is invalid to begin with. Always
set the continuous clock flag if the non-continuous property is not found.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Print debug info as standard V4L2 endpoint are parsed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Hans Verkuil