While running a single stream UDPv6 test, we observed that amount
of CPU spent in NET_RX softirq was much greater than UDPv4 for an
equivalent receive rate. The test here was run on an ARM64 based
Android system. On further analysis with perf, we found that UDPv6
was spending significant time in the statistics netfilter targets
which did socket lookup per packet. These statistics rules perform
a lookup when there is no socket associated with the skb. Since
there are multiple instances of these rules based on UID, there
will be equal number of lookups per skb.
By introducing early demux for UDPv6, we avoid the redundant lookups.
This also helped to improve the performance (800Mbps -> 870Mbps) on a
CPU limited system in a single stream UDPv6 receive test with 1450
byte sized datagrams using iperf.
v1->v2: Use IPv6 cookie to validate dst instead of 0 as suggested
by Eric
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c146066ab8 ("ipv4: Don't use ufo handling on later transformed
packets") and commit f89c56ce71 ("ipv6: Don't use ufo handling on
later transformed packets") added a check that 'rt->dst.header_len' isn't
zero in order to skip UFO, but it doesn't include IPcomp in transport mode
where it equals zero.
Packets, after payload compression, may not require further fragmentation,
and if original length exceeds MTU, later compressed packets will be
transmitted incorrectly. This can be reproduced with LTP udp_ipsec.sh test
on veth device with enabled UFO, MTU is 1500 and UDP payload is 2000:
* IPv4 case, offset is wrong + unnecessary fragmentation
udp_ipsec.sh -p comp -m transport -s 2000 &
tcpdump -ni ltp_ns_veth2
...
IP (tos 0x0, ttl 64, id 45203, offset 0, flags [+],
proto Compressed IP (108), length 49)
10.0.0.2 > 10.0.0.1: IPComp(cpi=0x1000)
IP (tos 0x0, ttl 64, id 45203, offset 1480, flags [none],
proto UDP (17), length 21) 10.0.0.2 > 10.0.0.1: ip-proto-17
* IPv6 case, sending small fragments
udp_ipsec.sh -6 -p comp -m transport -s 2000 &
tcpdump -ni ltp_ns_veth2
...
IP6 (flowlabel 0x6b9ba, hlim 64, next-header Compressed IP (108)
payload length: 37) fd00::2 > fd00::1: IPComp(cpi=0x1000)
IP6 (flowlabel 0x6b9ba, hlim 64, next-header Compressed IP (108)
payload length: 21) fd00::2 > fd00::1: IPComp(cpi=0x1000)
Fix it by checking 'rt->dst.xfrm' pointer to 'xfrm_state' struct, skip UFO
if xfrm is set. So the new check will include both cases: IPcomp and IPsec.
Fixes: c146066ab8 ("ipv4: Don't use ufo handling on later transformed packets")
Fixes: f89c56ce71 ("ipv6: Don't use ufo handling on later transformed packets")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions that are returning tcp sequence number also setup
TS offset value, so rename them to better describe their purpose.
No functional changes in this patch.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gso code of several tunnels type (gre and udp tunnels)
takes for granted that the skb->inner_protocol is properly
initialized and drops the packet elsewhere.
On the forwarding path no one is initializing such field,
so gro encapsulated packets are dropped on forward.
Since commit 3872035241 ("gre: Use inner_proto to obtain
inner header protocol"), this can be reproduced when the
encapsulated packets use gre as the tunneling protocol.
The issue happens also with vxlan and geneve tunnels since
commit 8bce6d7d0d ("udp: Generalize skb_udp_segment"), if the
forwarding host's ingress nic has h/w offload for such tunnel
and a vxlan/geneve device is configured on top of it, regardless
of the configured peer address and vni.
To address the issue, this change initialize the inner_protocol
field for encapsulated packets in both ipv4 and ipv6 gro complete
callbacks.
Fixes: 3872035241 ("gre: Use inner_proto to obtain inner header protocol")
Fixes: 8bce6d7d0d ("udp: Generalize skb_udp_segment")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dinesh reported that RTA_MULTIPATH nexthops are 8-bytes larger with IPv6
than IPv4. The recent refactoring for multipath support in netlink
messages does discriminate between non-multipath which needs the OIF
and multipath which adds a rtnexthop struct for each hop making the
RTA_OIF attribute redundant. Resolve by adding a flag to the info
function to skip the oif for multipath.
Fixes: beb1afac51 ("net: ipv6: Add support to dump multipath routes
via RTA_MULTIPATH attribute")
Reported-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2017-03-06
1) Fix lockdep splat on xfrm policy subsystem initialization.
From Florian Westphal.
2) When using socket policies on IPv4-mapped IPv6 addresses,
we access the flow informations of the wrong address family
what leads to an out of bounds access. Fix this by using
the family we get with the dst_entry, like we do it for the
standard policy lookup.
3) vti6 can report a PMTU below IPV6_MIN_MTU. Fix this by
adding a check for that before sending a ICMPV6_PKT_TOOBIG
message.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides equivalent functionality to the existing ipv4
"disable_policy" systcl. ie. Allows IPsec processing to be skipped
on terminating packets on a per-interface basis.
Signed-off-by: David Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix double-free in batman-adv, from Sven Eckelmann.
2) Fix packet stats for fast-RX path, from Joannes Berg.
3) Netfilter's ip_route_me_harder() doesn't handle request sockets
properly, fix from Florian Westphal.
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
Like commit 1f17e2f2c8 ("net: ipv6: ignore null_entry on route dumps"),
we need to ignore null entry in inet6_rtm_getroute() too.
Return -ENETUNREACH here to sync with IPv4 behavior, as suggested by David.
Fixes: a1a22c1206 ("net: ipv6: Keep nexthop of multipath route on admin down")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a NULL pointer deref bug in ipv6_route_ioctl()
-> ip6_route_del() -> __ip6_del_rt_siblings() code path. This is
because ip6_null_entry is returned in this path since ip6_null_entry
is kinda default for a ipv6 route table root node. Quote from
David Ahern:
ip6_null_entry is the root of all ipv6 fib tables making it integrated
into the table ...
We should ignore any attempt of trying to delete it, like we do in
__ip6_del_rt() path and several others.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Fixes: 0ae8133586 ("net: ipv6: Allow shorthand delete of all nexthops in multipath route")
Cc: David Ahern <dsa@cumulusnetworks.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This will add stricter validating for RTA_MARK attribute.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addr_gen_mode variable can be accessed by both sysctl and netlink.
Repleacd rtnl_lock() with rtnl_trylock() protect the sysctl operation to
avoid the possbile dead lock.`
Signed-off-by: Felix Jia <felix.jia@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Don't save TIPC header values before the header has been validated,
from Jon Paul Maloy.
2) Fix memory leak in RDS, from Zhu Yanjun.
3) We miss to initialize the UID in the flow key in some paths, from
Julian Anastasov.
4) Fix latent TOS masking bug in the routing cache removal from years
ago, also from Julian.
5) We forget to set the sockaddr port in sctp_copy_local_addr_list(),
fix from Xin Long.
6) Missing module ref count drop in packet scheduler actions, from
Roman Mashak.
7) Fix RCU annotations in rht_bucket_nested, from Herbert Xu.
8) Fix use after free which happens because L2TP's ipv4 support returns
non-zero values from it's backlog_rcv function which ipv4 interprets
as protocol values. Fix from Paul Hüber.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
qed: Don't use attention PTT for configuring BW
qed: Fix race with multiple VFs
l2tp: avoid use-after-free caused by l2tp_ip_backlog_recv
xfrm: provide correct dst in xfrm_neigh_lookup
rhashtable: Fix RCU dereference annotation in rht_bucket_nested
rhashtable: Fix use before NULL check in bucket_table_free
net sched actions: do not overwrite status of action creation.
rxrpc: Kernel calls get stuck in recvmsg
net sched actions: decrement module reference count after table flush.
lib: Allow compile-testing of parman
ipv6: check sk sk_type and protocol early in ip_mroute_set/getsockopt
sctp: set sin_port for addr param when checking duplicate address
net/mlx4_en: fix overflow in mlx4_en_init_timestamp()
netfilter: nft_set_bitmap: incorrect bitmap size
net: s2io: fix typo argumnet argument
net: vxge: fix typo argumnet argument
netfilter: nf_ct_expect: Change __nf_ct_expect_check() return value.
ipv4: mask tos for input route
ipv4: add missing initialization for flowi4_uid
lib: fix spelling mistake: "actualy" -> "actually"
...
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5e1859fbcc ("ipv4: ipmr: various fixes and cleanups") fixed
the issue for ipv4 ipmr:
ip_mroute_setsockopt() & ip_mroute_getsockopt() should not
access/set raw_sk(sk)->ipmr_table before making sure the socket
is a raw socket, and protocol is IGMP
The same fix should be done for ipv6 ipmr as well.
This patch can fix the panic caused by overwriting the same offset
as ipmr_table as in raw_sk(sk) when accessing other type's socket
by ip_mroute_setsockopt().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align vti6 with vti by returning GRE_KEY flag. This enables iproute2
to display tunnel keys on "ip -6 tunnel show"
Signed-off-by: David Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found that when randomized tcp offsets are enabled (by default)
TCP client can still start new connections without them. Later,
if server does active close and re-uses sockets in TIME-WAIT
state, new SYN from client can be rejected on PAWS check inside
tcp_timewait_state_process(), because either tw_ts_recent or
rcv_tsval doesn't really have an offset set.
Here is how to reproduce it with LTP netstress tool:
netstress -R 1 &
netstress -H 127.0.0.1 -lr 1000000 -a1
[...]
< S seq 1956977072 win 43690 TS val 295618 ecr 459956970
> . ack 1956911535 win 342 TS val 459967184 ecr 1547117608
< R seq 1956911535 win 0 length 0
+1. < S seq 1956977072 win 43690 TS val 296640 ecr 459956970
> S. seq 657450664 ack 1956977073 win 43690 TS val 459968205 ecr 296640
Fixes: 95a22caee3 ("tcp: randomize tcp timestamp offsets for each connection")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ip6_dst_lookup_tail has acquired a dst and fails the IPv4-mapped
check, release the dst before returning an error.
Fixes: ec5e3b0a1d ("ipv6: Inhibit IPv4-mapped src address on the wire.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-02-16
1) Make struct xfrm_input_afinfo const, nothing writes to it.
From Florian Westphal.
2) Remove all places that write to the afinfo policy backend
and make the struct const then.
From Florian Westphal.
3) Prepare for packet consuming gro callbacks and add
ESP GRO handlers. ESP packets can be decapsulated
at the GRO layer then. It saves a round through
the stack for each ESP packet.
Please note that this has a merge coflict between commit
63fca65d08 ("net: add confirm_neigh method to dst_ops")
from net-next and
3d7d25a68e ("xfrm: policy: remove garbage_collect callback")
a2817d8b27 ("xfrm: policy: remove family field")
from ipsec-next.
The conflict can be solved as it is done in linux-next.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In vti6_xmit(), the check for IPV6_MIN_MTU before we
send a ICMPV6_PKT_TOOBIG message is missing. So we might
report a PMTU below 1280. Fix this by adding the required
check.
Fixes: ccd740cbc6 ("vti6: Add pmtu handling to vti6_xmit.")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch adds GRO ifrastructure and callbacks for ESP on
ipv4 and ipv6.
In case the GRO layer detects an ESP packet, the
esp{4,6}_gro_receive() function does a xfrm state lookup
and calls the xfrm input layer if it finds a matching state.
The packet will be decapsulated and reinjected it into layer 2.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Add a skb_gro_flush_final helper to prepare for consuming
skbs in call_gro_receive. We will extend this helper to not
touch the skb if the skb is consumed by a gro callback with
a followup patch. We need this to handle the upcomming IPsec
ESP callbacks as they reinject the skb to the napi_gro_receive
asynchronous. The handler is used in all gro_receive functions
that can call the ESP gro handlers.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Add a new helper to set the secpath to the skb.
This avoids code duplication, as this is used
in multiple places.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch adds a check on the type of the source address for the case
where the destination address is in6addr_any. If the source is an
IPv4-mapped IPv6 source address, the destination is changed to
::ffff:127.0.0.1, and otherwise the destination is changed to ::1. This
is done in three locations to handle UDP calls to either connect() or
sendmsg() and TCP calls to connect(). Note that udpv6_sendmsg() delays
handling an in6addr_any destination until very late, so the patch only
needs to handle the case where the source is an IPv4-mapped IPv6
address.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check for the problematic case of an IPv4-mapped IPv6
source address and a destination address that is neither an IPv4-mapped
IPv6 address nor in6addr_any, and returns an appropriate error. The
check in done before returning from looking up the route.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the dst->pending_confirm flag was removed, we do not
need anymore to provide dst arg to dst_neigh_output.
So, rename it to neigh_output as before commit 5110effee8
("net: Do delayed neigh confirmation.").
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function igmpv3/mld_add_delrec() we allocate pmc and put it in
idev->mc_tomb, so we should free it when we don't need it in del_delrec().
But I removed kfree(pmc) incorrectly in latest two patches. Now fix it.
Fixes: 24803f38a5 ("igmp: do not remove igmp souce list info when ...")
Fixes: 1666d49e1d ("mld: do not remove mld souce list info when ...")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only needed it to register the policy backend at init time.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Just call xfrm_garbage_collect_deferred() directly.
This gets rid of a write to afinfo in register/unregister and allows to
constify afinfo later on.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Nothing writes to these structures (the module owner was not used).
While at it, size xfrm_input_afinfo[] by the highest existing xfrm family
(INET6), not AF_MAX.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We have many gro cells users, so lets move the code to avoid
duplication.
This creates a CONFIG_GRO_CELLS option.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under some circumstances it is possible that no new temporary addresses
will be generated.
For instance, addrconf_prefix_rcv_add_addr() indirectly calls
ipv6_create_tempaddr(), which creates a tentative temporary address and
starts dad. Next, addrconf_prefix_rcv_add_addr() indirectly calls
addrconf_verify_rtnl(). Now, assume that the previously created temporary
address has the least preferred lifetime among all existing addresses and
is still tentative (that is, dad is still running). Hence, the next run of
addrconf_verify_rtnl() is performed when the preferred lifetime of the
temporary address ends. If dad succeeds before the next run, the temporary
address becomes deprecated during the next run, but no new temporary
address is generated.
In order to fix this, schedule the next addrconf_verify_rtnl() run slightly
before the temporary address becomes deprecated, if dad succeeded.
Signed-off-by: Marcus Huewe <suse-tux@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
The datagram protocols can use MSG_CONFIRM to confirm the
neighbour. When used with MSG_PROBE we do not reach the
code where neighbour is confirmed, so we have to do the
same slow lookup by using the dst_confirm_neigh() helper.
When MSG_PROBE is not used, ip_append_data/ip6_append_data
will set the skb flag dst_pending_confirm.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effee8 ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bedf3 ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add confirm_neigh method to dst_ops and use it from IPv4 and IPv6
to lookup and confirm the neighbour. Its usage via the new helper
dst_confirm_neigh() should be restricted to MSG_PROBE users for
performance reasons.
For XFRM prefer the last tunnel address, if present. With help
from Steffen Klassert.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new skbuff flag to allow protocols to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
Add sock_confirm_neigh() helper to confirm the neighbour and
use it for IPv4, IPv6 and VRF before dst_neigh_output.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
net/ipv6/seg6_iptunnel.c:58:5: warning:
symbol 'nla_put_srh' was not declared. Should it be static?
net/ipv6/seg6_iptunnel.c:238:5: warning:
symbol 'seg6_input' was not declared. Should it be static?
net/ipv6/seg6_iptunnel.c:254:5: warning:
symbol 'seg6_output' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry reported that UDP sockets being destroyed would trigger the
WARN_ON(atomic_read(&sk->sk_rmem_alloc)); in inet_sock_destruct()
It turns out we do not properly destroy skb(s) that have wrong UDP
checksum.
Thanks again to syzkaller team.
Fixes : 7c13f97ffd ("udp: do fwd memory scheduling on dequeue")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When for instance a mobile Linux device roams from one access point to
another with both APs sharing the same broadcast domain and a
multicast snooping switch in between:
1) (c) <~~~> (AP1) <--[SSW]--> (AP2)
2) (AP1) <--[SSW]--> (AP2) <~~~> (c)
Then currently IPv6 multicast packets will get lost for (c) until an
MLD Querier sends its next query message. The packet loss occurs
because upon roaming the Linux host so far stayed silent regarding
MLD and the snooping switch will therefore be unaware of the
multicast topology change for a while.
This patch fixes this by always resending MLD reports when an interface
change happens, for instance from NO-CARRIER to CARRIER state.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry reported use-after-free in ip6_datagram_recv_specific_ctl()
A similar bug was fixed in commit 8ce48623f0 ("ipv6: tcp: restore
IP6CB for pktoptions skbs"), but I missed another spot.
tcp_v6_syn_recv_sock() can indeed set np->pktoptions from ireq->pktopts
Fixes: 971f10eca1 ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Konovalov reported out of bound accesses in ip6gre_err()
If GRE flags contains GRE_KEY, the following expression
*(((__be32 *)p) + (grehlen / 4) - 1)
accesses data ~40 bytes after the expected point, since
grehlen includes the size of IPv6 headers.
Let's use a "struct gre_base_hdr *greh" pointer to make this
code more readable.
p[1] becomes greh->protocol.
grhlen is the GRE header length.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_print_replace_route_err logs an error if a route replace fails with
IPv6 addresses in the full format. e.g,:
IPv6: IPV6: multipath route replace failed (check consistency of installed routes): 2001:0db8:0200:0000:0000:0000:0000:0000 nexthop 2001:0db8:0001:0000:0000:0000:0000:0016 ifi 0
Change the message to dump the addresses in the compressed format.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an entire multipath route is deleted using prefix and len (without any
nexthops), send a single RTM_DELROUTE notification with the full route
using RTA_MULTIPATH. This is done by generating the skb before the route
delete when all of the sibling routes are still present but sending it
after the route has been removed from the FIB. The skip_notify flag
is used to tell the lower fib code not to send notifications for the
individual nexthop routes.
If a route is deleted using RTA_MULTIPATH for any nexthops or a single
nexthop entry is deleted, then the nexthops are deleted one at a time with
notifications sent as each hop is deleted. This is necessary given that
IPv6 allows individual hops within a route to be deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ip6_route_multipath_add to send one notifciation with the full
route encoded with RTA_MULTIPATH instead of a series of individual routes.
This is done by adding a skip_notify flag to the nl_info struct. The
flag is used to skip sending of the notification in the fib code that
actually inserts the route. Once the full route has been added, a
notification is generated with all nexthops.
ip6_route_multipath_add handles 3 use cases: new routes, route replace,
and route append. The multipath notification generated needs to be
consistent with the order of the nexthops and it should be consistent
with the order in a FIB dump which means the route with the first nexthop
needs to be used as the route reference. For the first 2 cases (new and
replace), a reference to the route used to send the notification is
obtained by saving the first route added. For the append case, the last
route added is used to loop back to its first sibling route which is
the first nexthop in the multipath route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 returns multipath routes as a series of individual routes making
their display and handling by userspace different and more complicated
than IPv4, putting the burden on the user to see that a route is part of
a multipath route and internally creating a multipath route if desired
(e.g., libnl does this as of commit 29b71371e764). This patch addresses
this difference, allowing multipath routes to be returned using the
RTA_MULTIPATH attribute.
The end result is that IPv6 multipath routes can be treated and displayed
in a format similar to IPv4:
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 allows multipath routes to be deleted using just the prefix and
length. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.11.200.2 dev eth11.200 weight 1
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
$ ip ro del 1.1.1.0/24 vrf red
$ ip ro ls vrf red
unreachable default metric 8192
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
The same notation does not work with IPv6 because of how multipath routes
are implemented for IPv6. For IPv6 only the first nexthop of a multipath
route is deleted if the request contains only a prefix and length. This
leads to unnecessary complexity in userspace dealing with IPv6 multipath
routes.
This patch allows all nexthops to be deleted without specifying each one
in the delete request. Internally, this is done by walking the sibling
list of the route matching the specifications given (prefix, length,
metric, protocol, etc).
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 via 2001:db8:1::2 dev eth1 metric 1024 pref medium
2001:db8:200::/120 via 2001:db8:2::2 dev eth2 metric 1024 pref medium
...
$ ip -6 ro del vrf red 2001:db8:200::/120
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
...
Because IPv6 allows individual nexthops to be deleted without deleting
the entire route, the ip6_route_multipath_del and non-multipath code
path (ip6_route_del) have to be discriminated so that all nexthops are
only deleted for the latter case. This is done by making the existing
fc_type in fib6_config a u16 and then adding a new u16 field with
fc_delete_all_nh as the first bit.
Suggested-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, they are:
1) Stash ctinfo 3-bit field into pointer to nf_conntrack object from
sk_buff so we only access one single cacheline in the conntrack
hotpath. Patchset from Florian Westphal.
2) Don't leak pointer to internal structures when exporting x_tables
ruleset back to userspace, from Willem DeBruijn. This includes new
helper functions to copy data to userspace such as xt_data_to_user()
as well as conversions of our ip_tables, ip6_tables and arp_tables
clients to use it. Not surprinsingly, ebtables requires an ad-hoc
update. There is also a new field in x_tables extensions to indicate
the amount of bytes that we copy to userspace.
3) Add nf_log_all_netns sysctl: This new knob allows you to enable
logging via nf_log infrastructure for all existing netnamespaces.
Given the effort to provide pernet syslog has been discontinued,
let's provide a way to restore logging using netfilter kernel logging
facilities in trusted environments. Patch from Michal Kubecek.
4) Validate SCTP checksum from conntrack helper, from Davide Caratti.
5) Merge UDPlite conntrack and NAT helpers into UDP, this was mostly
a copy&paste from the original helper, from Florian Westphal.
6) Reset netfilter state when duplicating packets, also from Florian.
7) Remove unnecessary check for broadcast in IPv6 in pkttype match and
nft_meta, from Liping Zhang.
8) Add missing code to deal with loopback packets from nft_meta when
used by the netdev family, also from Liping.
9) Several cleanups on nf_tables, one to remove unnecessary check from
the netlink control plane path to add table, set and stateful objects
and code consolidation when unregister chain hooks, from Gao Feng.
10) Fix harmless reference counter underflow in IPVS that, however,
results in problems with the introduction of the new refcount_t
type, from David Windsor.
11) Enable LIBCRC32C from nf_ct_sctp instead of nf_nat_sctp,
from Davide Caratti.
12) Missing documentation on nf_tables uapi header, from Liping Zhang.
13) Use rb_entry() helper in xt_connlimit, from Geliang Tang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 stack does not set the protocol for local routes, so those routes show
up with proto "none":
$ ip -6 ro ls table local
local ::1 dev lo proto none metric 0 pref medium
local 2100:3:: dev lo proto none metric 0 pref medium
local 2100:3::4 dev lo proto none metric 0 pref medium
local fe80:: dev lo proto none metric 0 pref medium
...
Set rt6i_protocol to RTPROT_KERNEL for consistency with IPv4. Now routes
show up with proto "kernel":
$ ip -6 ro ls table local
local ::1 dev lo proto kernel metric 0 pref medium
local 2100:3:: dev lo proto kernel metric 0 pref medium
local 2100:3::4 dev lo proto kernel metric 0 pref medium
local fe80:: dev lo proto kernel metric 0 pref medium
...
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small cleanup factorizing code doing the TCP_MAXSEG clamping.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the latest version of the IPv6 Segment Routing IETF draft [1] the
cleanup flag is removed and the flags field length is shrunk from 16 bits
to 8 bits. As a consequence, the input of the HMAC computation is modified
in a non-backward compatible way by covering the whole octet of flags
instead of only the cleanup bit. As such, if an implementation compatible
with the latest draft computes the HMAC of an SRH who has other flags set
to 1, then the HMAC result would differ from the current implementation.
This patch carries those modifications to prevent conflict with other
implementations of IPv6 SR.
[1] https://tools.ietf.org/html/draft-ietf-6man-segment-routing-header-05
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 69b34fb996 ("netfilter: xt_LOG: add net namespace support for
xt_LOG") disabled logging packets using the LOG target from non-init
namespaces. The motivation was to prevent containers from flooding
kernel log of the host. The plan was to keep it that way until syslog
namespace implementation allows containers to log in a safe way.
However, the work on syslog namespace seems to have hit a dead end
somewhere in 2013 and there are users who want to use xt_LOG in all
network namespaces. This patch allows to do so by setting
/proc/sys/net/netfilter/nf_log_all_netns
to a nonzero value. This sysctl is only accessible from init_net so that
one cannot switch the behaviour from inside a container.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After this change conntrack operations (lookup, creation, matching from
ruleset) only access one instead of two sk_buff cache lines.
This works for normal conntracks because those are allocated from a slab
that guarantees hw cacheline or 8byte alignment (whatever is larger)
so the 3 bits needed for ctinfo won't overlap with nf_conn addresses.
Template allocation now does manual address alignment (see previous change)
on arches that don't have sufficent kmalloc min alignment.
Some spots intentionally use skb->_nfct instead of skb_nfct() helpers,
this is to avoid undoing the skb_nfct() use when we remove untracked
conntrack object in the future.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a helper to assign a nf_conn entry and the ctinfo bits to an sk_buff.
This avoids changing code in followup patch that merges skb->nfct and
skb->nfctinfo into skb->_nfct.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Followup patch renames skb->nfct and changes its type so add a helper to
avoid intrusive rename change later.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We should also toss nf_bridge_info, if any -- packet is leaving via
ip_local_out, also, this skb isn't bridged -- it is a locally generated
copy. Also this avoids the need to touch this later when skb->nfct is
replaced with 'unsigned long _nfct' in followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It is never accessed for reading and the only places that write to it
are the icmp(6) handlers, which also set skb->nfct (and skb->nfctinfo).
The conntrack core specifically checks for attached skb->nfct after
->error() invocation and returns early in this case.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Casting is a high precedence operation but "off" and "i" are in terms of
bytes so we need to have some parenthesis here.
Fixes: fbfa743a9d ("ipv6: fix ip6_tnl_parse_tlv_enc_lim()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 does not set the NLM_F_APPEND flag in notifications to signal that
a NEWROUTE is an append versus a new route or a replaced one. Add the
flag if the request has it.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-02-01
1) Some typo fixes, from Alexander Alemayhu.
2) Don't acquire state lock in get_mtu functions.
The only rece against a dead state does not matter.
From Florian Westphal.
3) Remove xfrm4_state_fini, it is unused for more than
10 years. From Florian Westphal.
4) Various rcu usage improvements. From Florian Westphal.
5) Properly handle crypto arrors in ah4/ah6.
From Gilad Ben-Yossef.
6) Try to avoid skb linearization in esp4 and esp6.
7) The esp trailer is now set up in different places,
add a helper for this.
8) With the upcomming usage of gro_cells in IPsec,
a gro merged skb can have a secpath. Drop it
before freeing or reusing the skb.
9) Add a xfrm dummy network device for napi. With
this we can use gro_cells from within xfrm,
it allows IPsec GRO without impact on the generic
networking code.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 will mark data that is smaller that mtu - headersize as
CHECKSUM_PARTIAL, but if the data will completely fill the mtu,
the packet checksum will be computed in software instead.
Extend the conditional to include the data that fills the mtu
as well.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing about lwt state requires a device reference, so remove the
input argument.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets arriving in a VRF currently are delivered to UDP sockets that
aren't bound to any interface. TCP defaults to not delivering packets
arriving in a VRF to unbound sockets. IP route lookup and socket
transmit both assume that unbound means using the default table and
UDP applications that haven't been changed to be aware of VRFs may not
function correctly in this case since they may not be able to handle
overlapping IP address ranges, or be able to send packets back to the
original sender if required.
So add a sysctl, udp_l3mdev_accept, to control this behaviour with it
being analgous to the existing tcp_l3mdev_accept, namely to allow a
process to have a VRF-global listen socket. Have this default to off
as this is the behaviour that users will expect, given that there is
no explicit mechanism to set unmodified VRF-unaware application into a
default VRF.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ipv4, this control socket is shared by all cpus so we cannot use
it as scratchpad area to annotate the mark that we pass to ip6_xmit().
Add a new parameter to ip6_xmit() to indicate the mark. The SCTP socket
family caches the flowi6 structure in the sctp_transport structure, so
we cannot use to carry the mark unless we later on reset it back, which
I discarded since it looks ugly to me.
Fixes: bf99b4ded5 ("tcp: fix mark propagation with fwmark_reflect enabled")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address generation mode for IPv6 link-local can only be configured
by netlink messages. This patch adds the ability to change the address
generation mode via sysctl.
v1 -> v2
Removed the rtnl lock and switch to use RCU lock to iterate through
the netdev list.
v2 -> v3
Removed the addrgenmode variable from the idev structure and use the
systcl storage for the flag.
Simplifed the logic for sysctl handling by removing the supported
for all operation.
Added support for more types of tunnel interfaces for link-local
address generation.
Based the patches from net-next.
v3 -> v4
Removed unnecessary whitespace changes.
Signed-off-by: Felix Jia <felix.jia@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
lkp-robot reported a BUG:
[ 10.151226] BUG: unable to handle kernel NULL pointer dereference at 00000198
[ 10.152525] IP: rt6_fill_node+0x164/0x4b8
[ 10.153307] *pdpt = 0000000012ee5001 *pde = 0000000000000000
[ 10.153309]
[ 10.154492] Oops: 0000 [#1]
[ 10.154987] CPU: 0 PID: 909 Comm: netifd Not tainted 4.10.0-rc4-00722-g41e8c70ee162-dirty #10
[ 10.156482] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 10.158254] task: d0deb000 task.stack: d0e0c000
[ 10.159059] EIP: rt6_fill_node+0x164/0x4b8
[ 10.159780] EFLAGS: 00010296 CPU: 0
[ 10.160404] EAX: 00000000 EBX: d10c2358 ECX: c1f7c6cc EDX: c1f6ff44
[ 10.161469] ESI: 00000000 EDI: c2059900 EBP: d0e0dc4c ESP: d0e0dbe4
[ 10.162534] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
[ 10.163482] CR0: 80050033 CR2: 00000198 CR3: 10d94660 CR4: 000006b0
[ 10.164535] Call Trace:
[ 10.164993] ? paravirt_sched_clock+0x9/0xd
[ 10.165727] ? sched_clock+0x9/0xc
[ 10.166329] ? sched_clock_cpu+0x19/0xe9
[ 10.166991] ? lock_release+0x13e/0x36c
[ 10.167652] rt6_dump_route+0x4c/0x56
[ 10.168276] fib6_dump_node+0x1d/0x3d
[ 10.168913] fib6_walk_continue+0xab/0x167
[ 10.169611] fib6_walk+0x2a/0x40
[ 10.170182] inet6_dump_fib+0xfb/0x1e0
[ 10.170855] netlink_dump+0xcd/0x21f
This happens when the loopback device is set down and a ipv6 fib route
dump is requested.
ip6_null_entry is the root of all ipv6 fib tables making it integrated
into the table and hence passed to the ipv6 route dump code. The
null_entry route uses the loopback device for dst.dev but may not have
rt6i_idev set because of the order in which initializations are done --
ip6_route_net_init is run before addrconf_init has initialized the
loopback device. Fixing the initialization order is a much bigger problem
with no obvious solution thus far.
The BUG is triggered when the loopback is set down and the netif_running
check added by a1a22c1206 fails. The fill_node descends to checking
rt->rt6i_idev for ignore_routes_with_linkdown and since rt6i_idev is
NULL it faults.
The null_entry route should not be processed in a dump request. Catch
and ignore. This check is done in rt6_dump_route as it is the highest
place in the callchain with knowledge of both the route and the network
namespace.
Fixes: a1a22c1206("net: ipv6: Keep nexthop of multipath route on admin down")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove skb_reserve and skb_reset_mac_header from inet6_rtm_getroute. The
allocated skb is not passed through the routing engine (like it is for
IPv4) and has not since the beginning of git time.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains a large batch with Netfilter fixes for
your net tree, they are:
1) Two patches to solve conntrack garbage collector cpu hogging, one to
remove GC_MAX_EVICTS and another to look at the ratio (scanned entries
vs. evicted entries) to make a decision on whether to reduce or not
the scanning interval. From Florian Westphal.
2) Two patches to fix incorrect set element counting if NLM_F_EXCL is
is not set. Moreover, don't decrenent set->nelems from abort patch
if -ENFILE which leaks a spare slot in the set. This includes a
patch to deconstify the set walk callback to update set->ndeact.
3) Two fixes for the fwmark_reflect sysctl feature: Propagate mark to
reply packets both from nf_reject and local stack, from Pau Espin Pedrol.
4) Fix incorrect handling of loopback traffic in rpfilter and nf_tables
fib expression, from Liping Zhang.
5) Fix oops on stateful objects netlink dump, when no filter is specified.
Also from Liping Zhang.
6) Fix a build error if proc is not available in ipt_CLUSTERIP, related
to fix that was applied in the previous batch for net. From Arnd Bergmann.
7) Fix lack of string validation in table, chain, set and stateful
object names in nf_tables, from Liping Zhang. Moreover, restrict
maximum log prefix length to 127 bytes, otherwise explicitly bail
out.
8) Two patches to fix spelling and typos in nf_tables uapi header file
and Kconfig, patches from Alexander Alemayhu and William Breathitt Gray.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new socket option, TCP_FASTOPEN_CONNECT, as an
alternative way to perform Fast Open on the active side (client). Prior
to this patch, a client needs to replace the connect() call with
sendto(MSG_FASTOPEN). This can be cumbersome for applications who want
to use Fast Open: these socket operations are often done in lower layer
libraries used by many other applications. Changing these libraries
and/or the socket call sequences are not trivial. A more convenient
approach is to perform Fast Open by simply enabling a socket option when
the socket is created w/o changing other socket calls sequence:
s = socket()
create a new socket
setsockopt(s, IPPROTO_TCP, TCP_FASTOPEN_CONNECT …);
newly introduced sockopt
If set, new functionality described below will be used.
Return ENOTSUPP if TFO is not supported or not enabled in the
kernel.
connect()
With cookie present, return 0 immediately.
With no cookie, initiate 3WHS with TFO cookie-request option and
return -1 with errno = EINPROGRESS.
write()/sendmsg()
With cookie present, send out SYN with data and return the number of
bytes buffered.
With no cookie, and 3WHS not yet completed, return -1 with errno =
EINPROGRESS.
No MSG_FASTOPEN flag is needed.
read()
Return -1 with errno = EWOULDBLOCK/EAGAIN if connect() is called but
write() is not called yet.
Return -1 with errno = EWOULDBLOCK/EAGAIN if connection is
established but no msg is received yet.
Return number of bytes read if socket is established and there is
msg received.
The new API simplifies life for applications that always perform a write()
immediately after a successful connect(). Such applications can now take
advantage of Fast Open by merely making one new setsockopt() call at the time
of creating the socket. Nothing else about the application's socket call
sequence needs to change.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove __sk_dst_reset() in the failure handling because __sk_dst_reset()
will eventually get called when sk is released. No need to handle it in
the protocol specific connect call.
This is also to make the code path consistent with ipv4.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modules implementing lwtunnel ops should not be allowed to unload
while there is state alive using those ops, so specify the owning
module for all lwtunnel ops.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function suffers from multiple issues.
First one is that pskb_may_pull() may reallocate skb->head,
so the 'raw' pointer needs either to be reloaded or not used at all.
Second issue is that NEXTHDR_DEST handling does not validate
that the options are present in skb->data, so we might read
garbage or access non existent memory.
With help from Willem de Bruijn.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ip6_tnl_parse_tlv_enc_lim() can call pskb_may_pull(),
we must reload any pointer that was related to skb->head
(or skb->data), or risk use after free.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add net.ipv4.ip_unprivileged_port_start, which is a per namespace sysctl
that denotes the first unprivileged inet port in the namespace. To
disable all privileged ports set this to zero. It also checks for
overlap with the local port range. The privileged and local range may
not overlap.
The use case for this change is to allow containerized processes to bind
to priviliged ports, but prevent them from ever being allowed to modify
their container's network configuration. The latter is accomplished by
ensuring that the network namespace is not a child of the user
namespace. This modification was needed to allow the container manager
to disable a namespace's priviliged port restrictions without exposing
control of the network namespace to processes in the user namespace.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we allocate per cpu storage, let's also use NUMA hints.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b05229f442 ("gre6: Cleanup GREv6 transmit path, call common GRE
functions") removed the ip6gre specific transmit function, but left the
struct ipv6_tel_txoption definition. Clean it up.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
seg6_genl_get_tunsrc() and set_tun_src() do not handle tun_src being
possibly NULL, so we must check kmemdup() return value and abort if
it is NULL
Fixes: 915d7e5e59 ("ipv6: sr: add code base for control plane support of SR-IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Lebrun <david.lebrun@uclouvain.be>
Acked-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 deletes route entries associated with multipath routes on an
admin down where IPv4 does not. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24 metric 64
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.100.2.254 dev eth2 weight 1
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.4
10.100.2.0/24 dev eth2 proto kernel scope link src 10.100.2.4
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:1::16 dev eth1 metric 1024 pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Set link down:
$ ip li set eth1 down
IPv4 retains the multihop route but flags eth1 route as dead:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.16 dev eth1 weight 1 dead linkdown
nexthop via 10.100.2.16 dev eth2 weight 1
10.100.2.0/24 dev eth2 proto kernel scope link src 10.100.2.4
and IPv6 deletes the route as part of flushing all routes for the device:
$ ip -6 ro ls vrf red
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Worse, on admin up of the device the multipath route has to be deleted
to get this leg of the route re-added.
This patch keeps routes that are part of a multipath route if
ignore_routes_with_linkdown is set with the dead and linkdown flags
enabling consistency between IPv4 and IPv6:
$ ip -6 ro ls vrf red
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:1::16 dev eth1 metric 1024 dead linkdown pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like commit 4acd4945cd ("ipv6: addrconf: Avoid calling
netdevice notifiers with RCU read-side lock"), it is unnecessary
to make addrconf_disable_change() use RCU iteration over the
netdev list, since it already holds the RTNL lock, or we may meet
Illegal context switch in RCU read-side critical section.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to add an mpls encap route when the MPLS modules are not loaded
hangs. For example:
CONFIG_MPLS=y
CONFIG_NET_MPLS_GSO=m
CONFIG_MPLS_ROUTING=m
CONFIG_MPLS_IPTUNNEL=m
$ ip route add 10.10.10.10/32 encap mpls 100 via inet 10.100.1.2
The ip command hangs:
root 880 826 0 21:25 pts/0 00:00:00 ip route add 10.10.10.10/32 encap mpls 100 via inet 10.100.1.2
$ cat /proc/880/stack
[<ffffffff81065a9b>] call_usermodehelper_exec+0xd6/0x134
[<ffffffff81065efc>] __request_module+0x27b/0x30a
[<ffffffff814542f6>] lwtunnel_build_state+0xe4/0x178
[<ffffffff814aa1e4>] fib_create_info+0x47f/0xdd4
[<ffffffff814ae451>] fib_table_insert+0x90/0x41f
[<ffffffff814a8010>] inet_rtm_newroute+0x4b/0x52
...
modprobe is trying to load rtnl-lwt-MPLS:
root 881 5 0 21:25 ? 00:00:00 /sbin/modprobe -q -- rtnl-lwt-MPLS
and it hangs after loading mpls_router:
$ cat /proc/881/stack
[<ffffffff81441537>] rtnl_lock+0x12/0x14
[<ffffffff8142ca2a>] register_netdevice_notifier+0x16/0x179
[<ffffffffa0033025>] mpls_init+0x25/0x1000 [mpls_router]
[<ffffffff81000471>] do_one_initcall+0x8e/0x13f
[<ffffffff81119961>] do_init_module+0x5a/0x1e5
[<ffffffff810bd070>] load_module+0x13bd/0x17d6
...
The problem is that lwtunnel_build_state is called with rtnl lock
held preventing mpls_init from registering.
Given the potential references held by the time lwtunnel_build_state it
can not drop the rtnl lock to the load module. So, extract the module
loading code from lwtunnel_build_state into a new function to validate
the encap type. The new function is called while converting the user
request into a fib_config which is well before any table, device or
fib entries are examined.
Fixes: 745041e2aa ("lwtunnel: autoload of lwt modules")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prefix arg to rt6_fill_node is non-0 in only 1 path - rt6_dump_route
where a user is requesting a prefix only dump. Simplify rt6_fill_node
by removing the prefix arg and moving the prefix check to rt6_dump_route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers of rt6_fill_node pass 0 for nowait arg. Remove the arg and
simplify rt6_fill_node accordingly.
rt6_fill_node passes the nowait of 0 to ip6mr_get_route. Remove the
nowait arg from it as well.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only difference between inet6_csk_bind_conflict and inet_csk_bind_conflict
is how they check the rcv_saddr, so delete this call back and simply
change inet_csk_bind_conflict to call inet_rcv_saddr_equal.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We pass these per-protocol equal functions around in various places, but
we can just have one function that checks the sk->sk_family and then do
the right comparison function. I've also changed the ipv4 version to
not cast to inet_sock since it is unneeded.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to setup the trailer in two different cases,
so add a helper to avoid code duplication.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch tries to avoid skb_cow_data on esp6.
On the encrypt side we add the IPsec tailbits
to the linear part of the buffer if there is
space on it. If there is no space on the linear
part, we add a page fragment with the tailbits to
the buffer and use separate src and dst scatterlists.
On the decrypt side, we leave the buffer as it is
if it is not cloned.
With this, we can avoid a linearization of the buffer
in most of the cases.
Joint work with:
Sowmini Varadhan <sowmini.varadhan@oracle.com>
Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
With ip6gre we have a tunnel header which also makes the tunnel MTU
smaller. We need to reserve room for it. Previously we were using up
space reserved for the Tunnel Encapsulation Limit option
header (RFC 2473).
Also, after commit b05229f442 ("gre6: Cleanup GREv6 transmit path,
call common GRE functions") our contract with the caller has
changed. Now we check if the packet length exceeds the tunnel MTU after
the tunnel header has been pushed, unlike before.
This is reflected in the check where we look at the packet length minus
the size of the tunnel header, which is already accounted for in tunnel
MTU.
Fixes: b05229f442 ("gre6: Cleanup GREv6 transmit path, call common GRE functions")
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an IPv6 version of commit 24803f38a5 ("igmp: do not remove igmp
souce list..."). In mld_del_delrec(), we will restore back all source filter
info instead of flush them.
Move mld_clear_delrec() from ipv6_mc_down() to ipv6_mc_destroy_dev() since
we should not remove source list info when set link down. Remove
igmp6_group_dropped() in ipv6_mc_destroy_dev() since we have called it in
ipv6_mc_down().
Also clear all source info after igmp6_group_dropped() instead of in it
because ipv6_mc_down() will call igmp6_group_dropped().
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we check the existing rtable in PREROUTING hook, if RTCF_LOCAL
is set, we assume that the packet is loopback.
But this assumption is incorrect, for example, a packet encapsulated
in ipsec transport mode was received and routed to local, after
decapsulation, it would be delivered to local again, and the rtable
was not dropped, so RTCF_LOCAL check would trigger. But actually, the
packet was not loopback.
So for these normal loopback packets, we can check whether the in device
is IFF_LOOPBACK or not. For these locally generated broadcast/multicast,
we can check whether the skb->pkt_type is PACKET_LOOPBACK or not.
Finally, there's a subtle difference between nft fib expr and xtables
rpfilter extension, user can add the following nft rule to do strict
rpfilter check:
# nft add rule x y meta iif eth0 fib saddr . iif oif != eth0 drop
So when the packet is loopback, it's better to store the in device
instead of the LOOPBACK_IFINDEX, otherwise, after adding the above
nft rule, locally generated broad/multicast packets will be dropped
incorrectly.
Fixes: f83a7ea207 ("netfilter: xt_rpfilter: skip locally generated broadcast/multicast, too")
Fixes: f6d0cbcf09 ("netfilter: nf_tables: add fib expression")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ah6 input processing uses the asynchronous hash crypto API which
supplies an error code as part of the operation completion but
the error code was being ignored.
Treat a crypto API error indication as a verification failure.
While a crypto API reported error would almost certainly result
in a memcpy of the digest failing anyway and thus the security
risk seems minor, performing a memory compare on what might be
uninitialized memory is wrong.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch removes the support of RFC5827 early retransmit (i.e.,
fast recovery on small inflight with <3 dupacks) because it is
subsumed by the new RACK loss detection. More specifically when
RACK receives DUPACKs, it'll arm a reordering timer to start fast
recovery after a quarter of (min)RTT, hence it covers the early
retransmit except RACK does not limit itself to specific inflight
or dupack numbers.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes RACK install a reordering timer when it suspects
some packets might be lost, but wants to delay the decision
a little bit to accomodate reordering.
It does not create a new timer but instead repurposes the existing
RTO timer, because both are meant to retransmit packets.
Specifically it arms a timer ICSK_TIME_REO_TIMEOUT when
the RACK timing check fails. The wait time is set to
RACK.RTT + RACK.reo_wnd - (NOW - Packet.xmit_time) + fudge
This translates to expecting a packet (Packet) should take
(RACK.RTT + RACK.reo_wnd + fudge) to deliver after it was sent.
When there are multiple packets that need a timer, we use one timer
with the maximum timeout. Therefore the timer conservatively uses
the maximum window to expire N packets by one timeout, instead of
N timeouts to expire N packets sent at different times.
The fudge factor is 2 jiffies to ensure when the timer fires, all
the suspected packets would exceed the deadline and be marked lost
by tcp_rack_detect_loss(). It has to be at least 1 jiffy because the
clock may tick between calling icsk_reset_xmit_timer(timeout) and
actually hang the timer. The next jiffy is to lower-bound the timeout
to 2 jiffies when reo_wnd is < 1ms.
When the reordering timer fires (tcp_rack_reo_timeout): If we aren't
in Recovery we'll enter fast recovery and force fast retransmit.
This is very similar to the early retransmit (RFC5827) except RACK
is not constrained to only enter recovery for small outstanding
flights.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current allocations are not NUMA aware, and lack proper
cleanup in case of error.
It is perfectly fine to use static per cpu allocations for 256 bytes
per cpu.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Lebrun <david.lebrun@uclouvain.be>
Acked-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle failure in lwtunnel_fill_encap adding attributes to skb.
Fixes: 571e722676 ("ipv4: support for fib route lwtunnel encap attributes")
Fixes: 19e42e4515 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GRO fast path caches the frag0 address. This address becomes
invalid if frag0 is modified by pskb_may_pull or its variants.
So whenever that happens we must disable the frag0 optimization.
This is usually done through the combination of gro_header_hard
and gro_header_slow, however, the IPv6 extension header path did
the pulling directly and would continue to use the GRO fast path
incorrectly.
This patch fixes it by disabling the fast path when we enter the
IPv6 extension header path.
Fixes: 78a478d0ef ("gro: Inline skb_gro_header and cache frag0 virtual address")
Reported-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o s/approriate/appropriate
o s/discouvery/discovery
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Direct call of tcp_set_keepalive() function from protocol-agnostic
sock_setsockopt() function in net/core/sock.c violates network
layering. And newly introduced protocol (SMC-R) will need its own
keepalive function. Therefore, add "keepalive" function pointer
to "struct proto", and call it from sock_setsockopt() via this pointer.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to avoid the atomic operation in icmp{v6,}_xmit_lock,
by checking the sysctl_icmp_msgs_per_sec ratelimit before these calls,
as pointed out by Eric Dumazet, but the BH disabled state must be correct.
The icmp_global_allow() call states it must be called with BH
disabled. This protection was given by the calls icmp_xmit_lock and
icmpv6_xmit_lock. Thus, split out local_bh_disable/enable from these
functions and maintain it explicitly at callers.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch split the global and per (inet)peer ICMP-reply limiter
code, and moves the global limit check to earlier in the packet
processing path. Thus, avoid spending cycles on ICMP replies that
gets limited/suppressed anyhow.
The global ICMP rate limiter icmp_global_allow() is a good solution,
it just happens too late in the process. The kernel goes through the
full route lookup (return path) for the ICMP message, before taking
the rate limit decision of not sending the ICMP reply.
Details: The kernels global rate limiter for ICMP messages got added
in commit 4cdf507d54 ("icmp: add a global rate limitation"). It is
a token bucket limiter with a global lock. It brilliantly avoids
locking congestion by only updating when 20ms (HZ/50) were elapsed. It
can then avoids taking lock when credit is exhausted (when under
pressure) and time constraint for refill is not yet meet.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SHA1 is slower and less secure than SipHash, and so replacing syncookie
generation with SipHash makes natural sense. Some BSDs have been doing
this for several years in fact.
The speedup should be similar -- and even more impressive -- to the
speedup from the sequence number fix in this series.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, RST packets generated by the TCP stack for non-existing
sockets always have mark 0.
The mark from the original packet is assigned to the netns_ipv4/6
socket used to send the response so that it can get copied into the
response skb when the socket sends it.
Fixes: e110861f86 ("net: add a sysctl to reflect the fwmark on replies")
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Pau Espin Pedrol <pau.espin@tessares.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Otherwise, RST packets generated by ipt_REJECT always have mark 0 when
the routing is checked later in the same code path.
Fixes: e110861f86 ("net: add a sysctl to reflect the fwmark on replies")
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Pau Espin Pedrol <pau.espin@tessares.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In matches and targets that define a kernel-only tail to their
xt_match and xt_target data structs, add a field .usersize that
specifies up to where data is to be shared with userspace.
Performed a search for comment "Used internally by the kernel" to find
relevant matches and targets. Manually inspected the structs to derive
a valid offsetof.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Convert ip6tables to copying entries, matches and targets one by one,
using the xt_match_to_user and xt_target_to_user helper functions.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
vti6 interface is registered before the rtnl_link_ops block
is attached. As a result the resulting RTM_NEWLINK is missing
IFLA_INFO_KIND. Re-order attachment of rtnl_link_ops block to fix.
Signed-off-by: Dave Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTM_NEWADDR notification is sent when IFA_F_TENTATIVE is cleared from
the address. So if the address is added and deleted before DAD probes
completes, the RTM_DELADDR will be sent for which there was no
RTM_NEWADDR causing asymmetry in notification. However if the same
logic is used while sending RTM_DELADDR notification, this asymmetry
can be avoided.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working with ipmr, we noticed that it is impossible to determine
if an entry is actually unresolved or its IIF interface has disappeared
(e.g. virtual interface got deleted). These entries look almost
identical to user-space when dumping or receiving notifications. So in
order to recognize them add a new RTNH_F_UNRESOLVED flag which is set when
sending an unresolved cache entry to user-space.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP_MULTICAST_IF fails if sk_bound_dev_if is already set and the new index
does not match it. e.g.,
ntpd[15381]: setsockopt IP_MULTICAST_IF 192.168.1.23 fails: Invalid argument
Relax the check in setsockopt to allow setting mc_index to an L3 slave if
sk_bound_dev_if points to an L3 master.
Make a similar change for IPv6. In this case change the device lookup to
take the rcu_read_lock avoiding a refcnt. The rcu lock is also needed for
the lookup of a potential L3 master device.
This really only silences a setsockopt failure since uses of mc_index are
secondary to sk_bound_dev_if if it is set. In both cases, if either index
is an L3 slave or master, lookups are directed to the same FIB table so
relaxing the check at setsockopt time causes no harm.
Patch is based on a suggested change by Darwin for a problem noted in
their code base.
Suggested-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
np is already assigned in the variable declaration of ping_v6_sendmsg.
At this point, we have already dereferenced np several times, so the
NULL check is also redundant.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an inconsistent conditional judgement between __ip6_append_data
and ip6_finish_output functions, the variable length in __ip6_append_data
just include the length of application's payload and udp6 header, don't
include the length of ipv6 header, but in ip6_finish_output use
(skb->len > ip6_skb_dst_mtu(skb)) as judgement, and skb->len include the
length of ipv6 header.
That causes some particular application's udp6 payloads whose length are
between (MTU - IPv6 Header) and MTU were fragmented by ip6_fragment even
though the rst->dev support UFO feature.
Add the length of ipv6 header to length in __ip6_append_data to keep
consistent conditional judgement as ip6_finish_output for ip6 fragment.
Signed-off-by: Zheng Li <james.z.li@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require fast recycling
TIME-WAIT sockets independently of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No point in going through loops and hoops instead of just comparing the
values.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Socket cmsg IP(V6)_RECVORIGDSTADDR checks that port range lies within
the packet. For sockets that have transport headers pulled, transport
offset can be negative. Use signed comparison to avoid overflow.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Reported-by: Nisar Jagabar <njagabar@cloudmark.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The protocol field is checked when deleting IPv4 routes, but ignored for
IPv6, which causes problems with routing daemons accidentally deleting
externally set routes (observed by multiple bird6 users).
This can be verified using `ip -6 route del <prefix> proto something`.
Signed-off-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user may call listen with binding an explicit port with the intent
that the kernel will assign an available port to the socket. In this
case inet_csk_get_port does a port scan. For such sockets, the user may
also set soreuseport with the intent a creating more sockets for the
port that is selected. The problem is that the initial socket being
opened could inadvertently choose an existing and unreleated port
number that was already created with soreuseport.
This patch adds a boolean parameter to inet_bind_conflict that indicates
rather soreuseport is allowed for the check (in addition to
sk->sk_reuseport). In calls to inet_bind_conflict from inet_csk_get_port
the argument is set to true if an explicit port is being looked up (snum
argument is nonzero), and is false if port scan is done.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains a large Netfilter update for net-next,
to summarise:
1) Add support for stateful objects. This series provides a nf_tables
native alternative to the extended accounting infrastructure for
nf_tables. Two initial stateful objects are supported: counters and
quotas. Objects are identified by a user-defined name, you can fetch
and reset them anytime. You can also use a maps to allow fast lookups
using any arbitrary key combination. More info at:
http://marc.info/?l=netfilter-devel&m=148029128323837&w=2
2) On-demand registration of nf_conntrack and defrag hooks per netns.
Register nf_conntrack hooks if we have a stateful ruleset, ie.
state-based filtering or NAT. The new nf_conntrack_default_on sysctl
enables this from newly created netnamespaces. Default behaviour is not
modified. Patches from Florian Westphal.
3) Allocate 4k chunks and then use these for x_tables counter allocation
requests, this improves ruleset load time and also datapath ruleset
evaluation, patches from Florian Westphal.
4) Add support for ebpf to the existing x_tables bpf extension.
From Willem de Bruijn.
5) Update layer 4 checksum if any of the pseudoheader fields is updated.
This provides a limited form of 1:1 stateless NAT that make sense in
specific scenario, eg. load balancing.
6) Add support to flush sets in nf_tables. This series comes with a new
set->ops->deactivate_one() indirection given that we have to walk
over the list of set elements, then deactivate them one by one.
The existing set->ops->deactivate() performs an element lookup that
we don't need.
7) Two patches to avoid cloning packets, thus speed up packet forwarding
via nft_fwd from ingress. From Florian Westphal.
8) Two IPVS patches via Simon Horman: Decrement ttl in all modes to
prevent infinite loops, patch from Dwip Banerjee. And one minor
refactoring from Gao feng.
9) Revisit recent log support for nf_tables netdev families: One patch
to ensure that we correctly handle non-ethernet packets. Another
patch to add missing logger definition for netdev. Patches from
Liping Zhang.
10) Three patches for nft_fib, one to address insufficient register
initialization and another to solve incorrect (although harmless)
byteswap operation. Moreover update xt_rpfilter and nft_fib to match
lbcast packets with zeronet as source, eg. DHCP Discover packets
(0.0.0.0 -> 255.255.255.255). Also from Liping Zhang.
11) Built-in DCCP, SCTP and UDPlite conntrack and NAT support, from
Davide Caratti. While DCCP is rather hopeless lately, and UDPlite has
been broken in many-cast mode for some little time, let's give them a
chance by placing them at the same level as other existing protocols.
Thus, users don't explicitly have to modprobe support for this and
NAT rules work for them. Some people point to the lack of support in
SOHO Linux-based routers that make deployment of new protocols harder.
I guess other middleboxes outthere on the Internet are also to blame.
Anyway, let's see if this has any impact in the midrun.
12) Skip software SCTP software checksum calculation if the NIC comes
with SCTP checksum offload support. From Davide Caratti.
13) Initial core factoring to prepare conversion to hook array. Three
patches from Aaron Conole.
14) Gao Feng made a wrong conversion to switch in the xt_multiport
extension in a patch coming in the previous batch. Fix it in this
batch.
15) Get vmalloc call in sync with kmalloc flags to avoid a warning
and likely OOM killer intervention from x_tables. From Marcelo
Ricardo Leitner.
16) Update Arturo Borrero's email address in all source code headers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Acctually ntohl and htonl are identical, so this doesn't affect
anything, but it is conceptually wrong.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
instead of allocating each xt_counter individually, allocate 4k chunks
and then use these for counter allocation requests.
This should speed up rule evaluation by increasing data locality,
also speeds up ruleset loading because we reduce calls to the percpu
allocator.
As Eric points out we can't use PAGE_SIZE, page_allocator would fail on
arches with 64k page size.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Keeps some noise away from a followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On SMP we overload the packet counter (unsigned long) to contain
percpu offset. Hide this from callers and pass xt_counters address
instead.
Preparation patch to allocate the percpu counters in page-sized batch
chunks.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_defrag modules for ipv4 and ipv6 export an empty stub function.
Any module that needs the defragmentation hooks registered simply 'calls'
this empty function to create a phony module dependency -- modprobe will
then load the defrag module too.
This extends netfilter ipv4/ipv6 defragmentation modules to delay the hook
registration until the functionality is requested within a network namespace
instead of module load time for all namespaces.
Hooks are only un-registered on module unload or when a namespace that used
such defrag functionality exits.
We have to use struct net for this as the register hooks can be called
before netns initialization here from the ipv4/ipv6 conntrack module
init path.
There is no unregister functionality support, defrag will always be
active once it was requested inside a net namespace.
The reason is that defrag has impact on nft and iptables rulesets
(without defrag we might see framents).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Made kernel accept IPv6 routes with IPv4-mapped address as next-hop.
It is possible to configure IP interfaces with IPv4-mapped addresses, and
one can add IPv6 routes for IPv4-mapped destinations/prefixes, yet prior
to this fix the kernel returned an EINVAL when attempting to add an IPv6
route with an IPv4-mapped address as a nexthop/gateway.
RFC 4798 (a proposed standard RFC) uses IPv4-mapped addresses as nexthops,
thus in order to support that type of address configuration the kernel
needs to allow IPv4-mapped addresses as nexthops.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tsq_flags being in the same cache line than sk_wmem_alloc
makes a lot of sense. Both fields are changed from tcp_wfree()
and more generally by various TSQ related functions.
Prior patch made room in struct sock and added sk_tsq_flags,
this patch deletes tsq_flags from struct tcp_sock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes use of nf_ct_netns_get/put added in previous patch.
We add get/put functions to nf_conntrack_l3proto structure, ipv4 and ipv6
then implement use-count to track how many users (nft or xtables modules)
have a dependency on ipv4 and/or ipv6 connection tracking functionality.
When count reaches zero, the hooks are unregistered.
This delays activation of connection tracking inside a namespace until
stateful firewall rule or nat rule gets added.
This patch breaks backwards compatibility in the sense that connection
tracking won't be active anymore when the protocol tracker module is
loaded. This breaks e.g. setups that ctnetlink for flow accounting and
the like, without any '-m conntrack' packet filter rules.
Followup patch restores old behavour and makes new delayed scheme
optional via sysctl.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
so that conntrack core will add the needed hooks in this namespace.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
currently aliased to try_module_get/_put.
Will be changed in next patch when we add functions to make use of ->net
argument to store usercount per l3proto tracker.
This is needed to avoid registering the conntrack hooks in all netns and
later only enable connection tracking in those that need conntrack.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_UDPLITE is no more a tristate. When set to y,
connection tracking support for UDPlite protocol is built-in into
nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_udplite,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| udplite| ipv4 | ipv6 |nf_conntrack
---------++--------+--------+--------+--------------
none || 432538 | 828755 | 828676 | 6141434
UDPlite || - | 829649 | 829362 | 6498204
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_SCTP is no more a tristate. When set to y, connection
tracking support for SCTP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_sctp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| sctp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 498243 | 828755 | 828676 | 6141434
SCTP || - | 829254 | 829175 | 6547872
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_DCCP is no more a tristate. When set to y, connection
tracking support for DCCP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_dccp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| dccp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 469140 | 828755 | 828676 | 6141434
DCCP || - | 830566 | 829935 | 6533526
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The email address has changed, let's update the copyright statements.
Signed-off-by: Arturo Borrero Gonzalez <arturo@debian.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Implemented RFC7527 Enhanced DAD.
IPv6 duplicate address detection can fail if there is some temporary
loopback of Ethernet frames. RFC7527 solves this by including a random
nonce in the NS messages used for DAD, and if an NS is received with the
same nonce it is assumed to be a looped back DAD probe and is ignored.
RFC7527 is enabled by default. Can be disabled by setting both of
conf/{all,interface}/enhanced_dad to zero.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
subashab@codeaurora.org