Triggered buffer support uses the HDC100X's dual acquisition mode
to read both humidity and temperature in one shot.
This patch depends on
447136effbf4 ("iio: humidity: hdc100x: fix sensor data reads of
temp and humidity")
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
MCP47x6 chip supports selection of a voltage reference (VDD, VREF buffered
or unbuffered). MCP4725 doesn't have this feature thus the eventual setting
is ignored and user is warned.
The setting is stored only in the volatile memory of the chip. You need to
manually store it to the EEPROM of the chip via 'store_eeprom' sysfs entry.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Number 2 is referencing to the settings with the largest available
resistor.
No functional change.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support to STM HTS221 humidity + temperature sensor
http://www.st.com/resource/en/datasheet/hts221.pdf
- continuous mode support
- i2c support
- spi support
- trigger mode support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during all raw write operations.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during required raw read cases.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Now the driver is in a reasonable state, lets get it (finally) out
of staging.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Move ISL29018/ISL29023/ISL29035 driver out of staging into mainline.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during raw reads.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during all write raw operations.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during raw reads.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use a standard framework to get the reference voltage. It is done that way
in the iio subsystem and it will simplify extending of the driver.
Structure mcp4725_platform_data is left undeleted because it used in the
next patch.
This change breaks the current users of the driver, but there is no
mainline user of struct mcp4725_platform_data.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change in handling of the regulator description means that static
checkers correctly assume we could be using dereferenced pointer to the
regulator. In reality we will never get the -ENODEV error, as current
behavior flow does not predict it, because:
If the device tree or board file does not define suitable regulators for
the component, it will be substituted by a dummy regulator, or, if
regulators are disabled altogether, by stubs.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There is a type mismatch between the buffer which is of type s16 and the
samples stored, which are declared as __le16.
Fix the following sparse warning:
drivers/iio/imu/bmi160/bmi160_core.c:411:26: warning: incorrect type
in assignment (different base types)
drivers/iio/imu/bmi160/bmi160_core.c:411:26: expected signed short
[signed] [short] [explicitly-signed] <noident>
drivers/iio/imu/bmi160/bmi160_core.c:411:26: got restricted __le16
[addressable] [usertype] sample
This is a cosmetic-type patch since it does not alter code behaviour.
The le16 is going into a 16bit buf element, and is labelled as IIO_LE in the
channel buffer definition.
Signed-off-by: sayli karnik <karniksayli1995@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add an iio driver for the MiraMEMS DA280 3-axis 14-bit accelerometer, as
well as for the DA226 which is a fully compatible 2-axis version.
Datasheets for the DA280 and DA226 can be found at the manufacturers site:
http://www.miramems.com/en/products.asp?list=1
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver is based on the DA311 Android driver which can be found here:
1e70113a5b/drivers/amlogic/input/sensor
the mir3da_* files are the DA311 driver.
Unfortunately there is no datasheet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a driver for the Domintech ARD10 3-axis Accelerometer, based on the
android driver found here: https://github.com/domintech/dmard10
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit 08e05d1fce ("ti-adc081c: Initial triggered buffer support") added
triggered buffer support but that also requires CONFIG_IIO_TRIGGERED_BUFFER,
otherwise we get errors from linker such as:
drivers/built-in.o: In function `adc081c_remove':
drivers/iio/adc/ti-adc081c.c:225: undefined reference to `iio_triggered_buffer_cleanup'
Fix these by explicitly selecting both CONFIG_IIO_TRIGGERED_BUFFER and
CONFIG_IIO_BUFFER in Kconfig for the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here is the big staging and IIO driver pull request for 4.9-rc1.
There are a lot of patches in here, the majority due to the
drivers/staging/greybus/ subsystem being merged in with full development
history that went back a few years, in order to preserve the work that
those developers did over time. This was done the same way that btrfs
was merged into the tree, so all should be ok there.
Lots and lots of tiny cleanups happened in the tree as well, due to the
Outreachy application process and lots of other developers showing up
for the first time to clean code up. Along with those changes, we
deleted a wireless driver, and added a raspberrypi driver (currently
marked broken), and lots of new iio drivers.
Overall the tree still shrunk with more lines removed than added, about
10 thousand lines removed in total. Full details are in the very long
shortlog below.
All of this has been in the linux-next tree with no issues. There will
be some merge problems with other subsystem trees, but those are all
minor problems and shouldn't be hard to work out when they happen
(MAINTAINERS and some lustre build problems with the IB tree.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlf0qWIPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfsp9GkAoLMa
Dl/S8W02azDtKP893es5GXh3AJ4k8J9JlHgTS0RlzVJMvzkSZ2x7Vg==
=j18s
-----END PGP SIGNATURE-----
Merge tag 'staging-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the big staging and IIO driver pull request for 4.9-rc1.
There are a lot of patches in here, the majority due to the
drivers/staging/greybus/ subsystem being merged in with full
development history that went back a few years, in order to preserve
the work that those developers did over time.
Lots and lots of tiny cleanups happened in the tree as well, due to
the Outreachy application process and lots of other developers showing
up for the first time to clean code up. Along with those changes, we
deleted a wireless driver, and added a raspberrypi driver (currently
marked broken), and lots of new iio drivers.
Overall the tree still shrunk with more lines removed than added,
about 10 thousand lines removed in total. Full details are in the very
long shortlog below.
All of this has been in the linux-next tree with no issues. There will
be some merge problems with other subsystem trees, but those are all
minor problems and shouldn't be hard to work out when they happen
(MAINTAINERS and some lustre build problems with the IB tree)"
And furter from me asking for clarification about greybus:
"Right now there is a phone from Motorola shipping with this code (a
slightly older version, but the same tree), so even though Ara is not
alive in the same form, the functionality is happening. We are working
with the developers of that phone to merge the newer stuff in with
their fork so they can use the upstream version in future versions of
their phone product line.
Toshiba has at least one chip shipping in their catalog that
needs/uses this protocol over a Unipro link, and rumor has it that
there might be more in the future.
There are also other users of the greybus protocols, there is a talk
next week at ELC that shows how it is being used across a network
connection to control a device, and previous ELC talks have showed the
protocol stack being used over USB to drive embedded Linux boards.
I've also talked to some people who are starting to work to add a host
controller driver to control arduinos as the greybus PHY protocols are
very useful to control a serial/i2c/spio/whatever device across a
random physical link, as it is a way to have a self-describing device
be attached to a host without needing manual configuration.
So yes, people are using it, and there is still the chance that it
will show up in a phone/laptop/tablet/whatever from Google in the
future as well, the tech isn't dead, even if the original large phone
project happens to be"
* tag 'staging-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (3703 commits)
Staging: fbtft: Fix bug in fbtft-core
staging: rtl8188eu: fix double unlock error in rtw_resume_process()
staging:r8188eu: remove GEN_MLME_EXT_HANDLER macro
staging:r8188eu: remove GEN_DRV_CMD_HANDLER macro
staging:r8188eu: remove GEN_EVT_CODE macro
staging:r8188eu: remove GEN_CMD_CODE macro
staging:r8188eu: remove pkt_newalloc member of the recv_buf structure
staging:r8188eu: remove rtw_handle_dualmac declaration
staging:r8188eu: remove (RGTRY|BSSID)_(OFT|SZ) macros
staging:r8188eu: change rtl8188e_process_phy_info function argument type
Staging: fsl-mc: Remove blank lines
Staging: fsl-mc: Fix unaligned * in block comments
Staging: comedi: Align the * in block comments
Staging : ks7010 : Fix block comments warninig
Staging: vt6655: Remove explicit NULL comparison using Coccinelle
staging: rtl8188eu: core: rtw_xmit: Use macros instead of constants
staging: rtl8188eu: core: rtw_xmit: Move constant of the right side
staging: dgnc: Fix lines longer than 80 characters
Staging: dgnc: constify attribute_group structures
Staging: most: hdm-dim2: constify attribute_group structures
...
Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems that
flow through me. Nothing major that I can discern, full details are in
the shortlog.
All have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFUEABECABYFAlfyOIQPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfsp9OQAlRy3
gSKfQUlXjTs96Bx/I5PtWysAn0r8nyKZoP1oSgsTddOCEeXngTXc
=4uPs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems
that flow through me. Nothing major that I can discern, full details
are in the shortlog.
All have been in the linux-next tree with no reported issues"
* tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (144 commits)
drivers/misc/hpilo: Changes to support new security states in iLO5 FW
at25: fix debug and error messaging
misc/genwqe: ensure zero initialization
vme: fake: remove unexpected unlock in fake_master_set()
vme: fake: mark symbols static where possible
spmi: pmic-arb: Return an error code if sanity check fails
Drivers: hv: get rid of id in struct vmbus_channel
Drivers: hv: make VMBus bus ids persistent
mcb: Add a dma_device to mcb_device
mcb: Enable PCI bus mastering by default
mei: stop the stall timer worker if not needed
clk: probe common clock drivers earlier
vme: fake: fix build for 64-bit dma_addr_t
ttyprintk: Neaten and simplify printing
mei: me: add kaby point device ids
coresight: tmc: mark symbols static where possible
coresight: perf: deal with error condition properly
Drivers: hv: hv_util: Avoid dynamic allocation in time synch
fpga manager: Add hardware dependency to Zynq driver
Drivers: hv: utils: Support TimeSync version 4.0 protocol samples.
...
Fixes two cases of 'cast to restricted __le16' as reported by sparse.
Signed-off-by: Ico Doornekamp <ico@pruts.nl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ACCES 104-QUAD-8 is a general purpose quadrature encoder
counter/interface board. The 104-QUAD-8 is capable of monitoring the
outputs of eight encoders via four on-board LSI/CSI LS7266R1 24-bit
dual-axis quadrature counter chips. Core functions handled by the
LS7266R1, such as direction and total count, are available.
Performing a write to a counter's IIO_CHAN_INFO_RAW sets the counter and
also clears the counter's respective error flag. Although the counters
have a 25-bit range, only the lower 24 bits may be set, either directly
or via a counter's preset attribute. Interrupts are not supported by
this driver.
This driver adds IIO support for the ACCES 104-QUAD-8 and ACCES
104-QUAD-4. The base port addresses for the devices may be configured
via the base array module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Quadrature encoders, such as rotary encoders and linear encoders, are
devices which are capable of encoding the relative position and
direction of motion of a shaft. This patch introduces several IIO
constants for supporting quadrature encoder counter devices.
IIO_COUNT: Current count (main data provided by the counter device)
IIO_INDEX: Counter device index value
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds minimal driver for the Honeywell Amplified Basic
Pressure sensors series. Sensors are pretty simple but are
available in many variants:
- psi/mbar/kPa output,
- analog/i2c/spi,
- gage/differential measurement,
- different measure ranges etc.
Refer to datasheets for more details:
http://sensing.honeywell.com/honeywell-sensing-basic-board-mount-pressure-sensors-abp-series-datasheet-323005128-c-en.pdfhttp://sensing.honeywell.com/index.php%3Fci_id%3D45841
Driver internals:
- i2c only. measure request is done by the SMBUS QUICK cmd, so if the i2c
bus doesn't support it, it is required to send a dummy byte to trigger
measurement,
- since iio sysfs expects kilopascals, mbar-variants are treated as their
respective kPa-s, hence i2c id-table has doubled entries in one line:
{ "abp060mg", ABP006KG }, { "abp006kg", ABP006KG },
- psi-variants have prescaled values in config,
- no temperature reads yet.
Work remained:
- optional temperature channel,
- SPI support,
- DT binding.
Changes since v1:
- mutex is now locked in read_raw(),
- corrected error codes,
- fixed coding style issues,
- renamed few defines and functions abp -> abp060mg
(some structs left as they were to keep the sensible meaning).
Signed-off-by: Marcin Malagowski <mrc@bourne.st>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was reporting invalid raw read values for MAX6675 on big
endian architectures. MAX6675 buffered mode is not affected, nor
is the MAX31855.
The driver was losing a 2 byte read value when it used a 32 bit
integer buffer to store a 16 bit big endian value. Use big endian
types to properly align buffers on big endian architectures.
Fixes following sparse endianness warnings:
warning: cast to restricted __be16
warning: cast to restricted __be32
Fixes checkpatch issue:
CHECK: No space is necessary after a cast
Signed-off-by: sayli karnik <karniksayli1995@gmail.com>
Fixes: 1f25ca11d8 ("iio: temperature: add support for Maxim
thermocouple chips")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the LMP91000 potentiostat which is used for chemical
sensing applications.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Allow IIO_CHAN_INFO_SCALE and IIO_CHAN_INFO_OFFSET attributes for
processing by checking voltage from a regulator.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Allow access to underlying channel IIO_CHAN_INFO_OFFSET from a consumer.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1, AD7767-2
Analog to Digital converters. It's a family of single channel 24-bit SAR
ADCs. They are all digital interface compatible and the main difference is
the internal decimation rate and analog performance. For communication with
the host processor a SPI interface is used.
In addition the part has a data ready pin that is pulsed for one MCLK cycle
when a conversion has completed and can be used as a IIO trigger.
Datasheets:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD7766.pdfhttp://www.analog.com/media/en/technical-documentation/data-sheets/AD7767.pdf
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the new iio_trigger_validate_own_device() to verify that the trigger
can only be attached to the matching IIO device rather than using a custom
variant.
While the implementation of iio_trigger_validate_own_device() and the
custom variant and are not identical their behaviour is.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the new iio_trigger_validate_own_device() to verify that the trigger
can only be attached to the matching IIO device rather than using a custom
variant.
While the implementation of iio_trigger_validate_own_device() and the
custom variant and are not identical their behaviour is.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some triggers can only be attached to the IIO device that corresponds to
the same physical device. Currently each driver that requires this
implements its own trigger validation function.
Introduce a new helper function called iio_trigger_validate_own_device()
that can be used to do this check. Having a common implementation avoids
code duplication and unnecessary boiler-plate code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fixes the following sparse warning:
drivers/iio/accel/mma7660.c:42:11: warning:
symbol 'mma7660_nscale' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The -Wempty-body gcc warning triggers in the newly added zpa2326 driver:
drivers/iio/pressure/zpa2326.c: In function 'zpa2326_dequeue_pressure':
drivers/iio/pressure/zpa2326.c:578:3: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
The use of an empty statement behind 'if (...)' is harmless here, but
it shows that the dev_dbg() macro is not used correctly: when the "DEBUG"
macro is not set, dev_dbg() already defaults to a no-operation, though
one that lets the compiler know that the arguments are used, and lets
it check the format string.
Fixing this also simplifies the driver.
Fixes: 03b262f2bb ("iio:pressure: initial zpa2326 barometer support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The si114x supports x=1,2,3 IR LEDs for proximity sensing together with
visible and IR ambient light sensing (ALS).
Newer parts (si1132, si1145/6/7) can measure UV light and compute an UV
index
This was tested on si1143 and si1145
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add missing MODULE_DEVICE_TABLE(i2c) this fixes autoloading on
devicetree using systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for iio_info structures that are only stored in the info field of a
iio_dev structure. This field is declared const, so iio_info structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct iio_info i@p = { ... };
@ok@
identifier r.i;
struct iio_dev e;
position p;
@@
e.info = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct iio_info e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct iio_info i = { ... };
// </smpl>
The result of size on this file before the change is:
text data bss dec hex filename
1245 344 0 1589 635
drivers/iio/gyro/ssp_gyro_sensor.o
and after the change it is:
text data bss dec hex filename
1397 192 0 1589 635
drivers/iio/gyro/ssp_gyro_sensor.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for iio_info structures that are only stored in the info field of a
iio_dev structure. This field is declared const, so iio_info structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct iio_info i@p = { ... };
@ok@
identifier r.i;
struct iio_dev e;
position p;
@@
e.info = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct iio_info e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct iio_info i = { ... };
// </smpl>
The result of size on this file before the change is:
text data bss dec hex filename
1529 312 0 1841 731
drivers/iio/adc/men_z188_adc.o
and after the change it is:
text data bss dec hex filename
1689 168 0 1857 741
drivers/iio/adc/men_z188_adc.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for iio_info structures that are only stored in the info field of a
iio_dev structure. This field is declared const, so iio_info structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct iio_info i@p = { ... };
@ok@
identifier r.i;
struct iio_dev e;
position p;
@@
e.info = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct iio_info e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct iio_info i = { ... };
// </smpl>
The result of size on this file before the change is:
text data bss dec hex filename
1265 344 0 1609 649
drivers/iio/accel/ssp_accel_sensor.o
and after the change it is:
text data bss dec hex filename
1425 192 0 1617 651
drivers/iio/accel/ssp_accel_sensor.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the mounting matrix to the KXSD9 driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This deploys runtime and system PM in the KXSD9 driver:
- Use the force_runtime_suspend/resume callbacks as system PM
operations.
- Add buffer prepare/unprepare callbacks to grab the runtime
PM while we're using buffered reads and put get/put_autosuspend
in these.
- Insert get/put_autosuspend calls anywhere the IO is used from
the raw read/write callbacks.
- Move the fullscale setting to be cached in the state container
so we can restore it properly when coming back from
system/runtime suspend.
- Set the autosuspend delay to two orders of magnitude that of
the sensor start-up time (20ms) so we will autosuspend after
2s.
- Register the callbacks in both the SPI and I2C subdrivers.
Tested with the I2C KXSD9 on the Qualcomm APQ8060 Dragonboard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
What is passed to the .probe() and .remove() functions is
technically the parent of the created IIO device but it becomes
a big confusion for the head to have it named like this since
it is usually clear from context the "dev" refers to the physical
device, and when next adding PM callbacks a clean
"struct device *dev" pointer is passed to these and that makes
it even more confused. Rename "parent" to "dev" like in most
other drivers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds supply regulator handling for the VDD and IOVDD inputs
on the KXSD9 component, makes sure to bring the regulators online
during probe and disable them on remove or the errorpath.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are some hardcoded register values etc in the code, define
proper bitfield definitions, and use them when getting and setting
the scale. Optimize a read/modify/write to use regmap_update_bits()
at the same time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
As is custom with all modern sensors, add a clever burst mode
that will just stream out values from the sensor and provide it
to userspace to do the proper offsetting and scaling.
This is the result when tested with an HRTimer trigger:
$ generic_buffer -a -c 10 -n kxsd9 -t foo
/sys/bus/iio/devices/iio:device1 foo
0.371318 0.718680 9.869872 1795.000000 97545896129
-0.586922 0.179670 9.378775 2398.000000 97555864721
-0.299450 0.179670 10.348992 2672.000000 97565874055
0.371318 0.335384 11.103606 2816.000000 97575883240
0.179670 0.574944 10.540640 2847.000000 97585862351
0.335384 0.754614 9.953718 2840.000000 97595872425
0.179670 0.754614 10.732288 2879.000000 97605882351
0.000000 0.754614 10.348992 2872.000000 97615891832
-0.730658 0.574944 9.570422 2831.000000 97625871536
0.000000 1.137910 10.732288 2872.000000 97635881610
Columns shown are x, y, z acceleration, so a positive acceleration
of ~9.81 (shaky due to bad calibration) along the z axis. The
fourth column is the AUX IN which is floating on this system,
it seems to float up to the 2.85V VDD voltage.
To be able to cleanup the triggered buffer, we need to add .remove()
callbacks to the I2C and SPI subdrivers and call back into an
exported .remove() callback in the core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes several errors in the offset and scaling of the raw
values from the KXSD9 sensor:
- The code did not convert the big endian value from the sensor
into the endianness of the host CPU. Fix this with
be16_to_cpu() on the raw obtained value.
- The code did not regard the fact that only the upper 12 bits of
the accelerometer values are valid. Shift these
down four bits to yield the real raw value.
- Further the sensor provides 2048 at zero g. This means that an
offset of 2048 must be subtracted from the raw value before
scaling. This was not taken into account by the driver,
yielding a weird value. Fix this by providing this offset in
sysfs.
To house the scaling code better, the value reading code was
factored into the raw reading function.
This proper scaling and offseting is necessary to get proper
values out of triggered buffer by offsetting, shifting and scaling
them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The RX/TX buffers are gone so drop the lock (it should have been
in the transport struct anyway).
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds I2C regmap transport for the KXSD9 driver.
Tested on the KXSD9 sensor on the APQ8060 Dragonboard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This converts the KXSD9 driver to drop the custom transport
mechanism and just use regmap like everything else.
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is just a masquerading register write function, so use the
register write function instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This moves the KXSD9 SPI transport out to its own file and Kconfig
entry, so that we will be able to add another transport method.
We export the common probe and add a local header file for the
functionality shared between the main driver and the transport
driver.
We make the SPI transport the default for the driver if SPI is
available and the KXSD9 driver was selected, so the oldconfig
upgrade path will be clear.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This makes it possible to later split the transport mechanism
using a generic probe() and a generic remove().
Use dev_set_drvdata() and dev_get_drvdata() as a paired
accessor to operate on the abstract struct device * regardless
of the transport mechanism in use.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Split off a transport mechanism struct that will deal with the SPI
traffic in preparation for adding I2C support.
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
-----BEGIN PGP SIGNATURE-----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=V1xL
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.9b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of iio new device support, features and cleanups for the 4.9 cycle.
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
The initial commit adding support for the mxc6225 assumed the
mxc6225 has a chip-id of 0xe5 based on testing on a single Allwinner
A23 tablet with a mxc6225. Testing on a bunch of other Allwinner
tablets have shown that the chip-id for the mxc6225 is not constant.
A datasheet for the MXC6255 which I've found online says that bits
7 and 6 of the chip-id register are undefined (for the mxc6255), testing
on 5 different tablets with a mxc6225 has found the following ids:
0x25, 0x45, 0x65, 0x85, 0xe5. So it seems that for the mxc6225 bits
7, 6 and 5 of the chip-id register are undefined.
This commit adjusts the chip-id check so that the mxc6255 driver
properly recognizes the mxc6225 in all these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ST sensors can be used as a trigger for its own triggered buffer
but it is also possible to use an external trigger: a HRTimer or
even a different sensor (!) as trigger. In that case we should not
pick the timestamp from our own interrupt top half even if it is
active.
This could practically happen if some other sensor is using the
ST sensor as trigger but the ST sensor itself is using e.g.
an HRTimer as trigger. So the trigger is on, but not used by us.
We used to assume that whenever the hardware interrupt is turned
on, we are using it for our own trigger, but this is an
oversimplification.
Handle this logically by using the iio_trigger_using_own() helper.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Cc: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds a helper function to the IIO trigger framework:
iio_trigger_using_own(): for an IIO device, this tells
whether the device is using itself as a trigger.
This is true if the indio device:
(A) supplies a trigger and
(B) has assigned its own buffer poll function to use this
trigger.
This helper function is good when constructing triggered,
buffered drivers that can either use its own hardware *OR*
an external trigger such as a HRTimer or even the trigger from
a totally different sensor.
Under such circumstances it is important to know for example
if the timestamp from the same trigger hardware should be used
when populating the buffer: if iio_trigger_using_own() is true,
we can use this timestamp, else we need to pick a unique
timestamp directly in the trigger handler.
For this to work of course IIO devices registering hardware
triggers must follow the convention to set the parent device
properly, as as well as setting the parent of the IIO device
itself.
When a new poll function is attached, we check if the parent
device of the IIO of the poll function is the same as the
parent device of the trigger and in that case we conclude that
the hardware is using itself as trigger.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Cc: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
iio_push_event() operates on a struct iio_dev. This struct can be allocated
using iio_device_alloc() which returns a valid struct iio_dev pointer. But
iio_push_event() is not safe to use on such a iio_dev until
iio_device_register() for the same device has successfully completed.
This restriction is not documented anywhere and most drivers are written
with the assumption that this restriction does not exist. The basic pattern
that is followed by all drivers looks like the following:
irqreturn_t event_callback(int irq, void *devid)
{
struct iio_dev *indio_dev = devid;
...
iio_push_event(indio_dev, ...);
return IRQ_HANDLED;
}
int driver_probe(struct device *dev)
{
struct iio_dev *indio_dev;
indio_dev = iio_device_alloc(...);
request_irq(event_irq, event_callback, ..., indio_dev);
return iio_device_register(indio_dev);
}
And while it is unlikely that the IRQ fires before iio_device_register()
completes (e.g. because the IRQ is disabled in the device) it is not
impossible and might be triggered by glitches on the signal line or
incorrect hardware configuration.
To avoid undefined behaviour in such a case extend iio_push_event() to
check if the event has been registered and discard generated events if it
has not.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We have a big rework of the kxsd9 driver queued up behind the fix below and
a fix for a recent fix that was marked for stable.
Hence this fix series is perhaps a little more urgent than average for IIO.
* core
- a fix for a fix in the last set. The recent fix for blocking ops when
! task running left a path (unlikely one) in which the function return
value was not set - so initialise it to 0.
- The IIO_TYPE_FRACTIONAL code previously didn't cope with negative
fractions. Turned out a fix for this was in Analog's tree but hadn't made
it upstream.
* bmc150
- reset chip at init time. At least one board out there ends up coming up
in an unstable state due to noise during power up. The reset does no
harm on other boards.
* kxsd9
- Fix a bug in the reported scaling due to failing to set the integer
part to 0.
* hid-sensors-pressure
- Output was in the wrong units to comply with the IIO ABI.
* tools
- iio_generic_buffer: Fix the trigger-less mode by ensuring we don't fault
out for having no trigger when we explicitly said we didn't want to have
one.
-----BEGIN PGP SIGNATURE-----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=Ob6a
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.8 cycle.
We have a big rework of the kxsd9 driver queued up behind the fix below and
a fix for a recent fix that was marked for stable.
Hence this fix series is perhaps a little more urgent than average for IIO.
* core
- a fix for a fix in the last set. The recent fix for blocking ops when
! task running left a path (unlikely one) in which the function return
value was not set - so initialise it to 0.
- The IIO_TYPE_FRACTIONAL code previously didn't cope with negative
fractions. Turned out a fix for this was in Analog's tree but hadn't made
it upstream.
* bmc150
- reset chip at init time. At least one board out there ends up coming up
in an unstable state due to noise during power up. The reset does no
harm on other boards.
* kxsd9
- Fix a bug in the reported scaling due to failing to set the integer
part to 0.
* hid-sensors-pressure
- Output was in the wrong units to comply with the IIO ABI.
* tools
- iio_generic_buffer: Fix the trigger-less mode by ensuring we don't fault
out for having no trigger when we explicitly said we didn't want to have
one.
7985e7c100 ("iio: Introduce a new fractional value type") introduced a
new IIO_VAL_FRACTIONAL value type meant to represent rational type numbers
expressed by a numerator and denominator combination.
Formating of IIO_VAL_FRACTIONAL values relies upon do_div() usage. This
fails handling negative values properly since parameters are reevaluated
as unsigned values.
Fix this by using div_s64_rem() instead. Computed integer part will carry
properly signed value. Formatted fractional part will always be positive.
Fixes: 7985e7c100 ("iio: Introduce a new fractional value type")
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mxc6225 is fully compatible with the existing mxc6255 driver,
add support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On newer components compatible with the at91sam9x5, the Touchscreen
Switches Closure Time or TSSCTIM value of the Touchscreen Mode Register is
not filled at all.
On some hardware, having no time indicated for it may lead to incoherent
values and jitter.
We fix this time to 10us as it is usually difficult to retrieve impedance
values from LCD manufacturers.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch is inspired by a comment of Jonathan Cameron on patch of
Linus Walleij commit aeb55fff38 ("iio:
st_sensors: fetch and enable regulators unconditionally"). Because
changes made in this patch are actually reference generators they should
be using devm_regulator_get_optional, but if they do not explicitly set
the reference to NULL they should not be using IS_ERR_OR_NULL, but
simple IS_ERR check.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch is inspired by a comment of Jonathan Cameron on patch of
Linus Walleij commit aeb55fff38 ("iio: st_sensors: fetch and enable regulators unconditionally").
The explanation for this change is same as in that patch:
"Supplies are *not* optional (optional means that the supply is
optional in the electrical sense, not the software sense) so we need to
get the and enable them at all times.
If the device tree or board file does not define suitable regulators for
the component, it will be substituted by a dummy regulator, or, if
regulators are disabled altogether, by stubs. There is no need to use the
IS_ERR_OR_NULL() check that is considered harmful.
Reported-by: Linus Wallerij <linus.walleij@linaro.org>
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A recent fix to iio_buffer_read_first_n_outer removed ret from being set by
a return from wait_event_interruptible and also added a continue in a loop
which causes the variable ret to not be set when it reaches the end of the
loop. Fix this by initializing ret to zero.
Also remove extraneous white space at the end of the loop.
Fixes: fcf68f3c0b ("fix sched WARNING "do not call blocking ops when !TASK_RUNNING")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add resource managed devm_iio_triggered_buffer_setup() and
devm_iio_triggered_buffer_cleanup() to automatically clean up triggered
buffers setup by IIO drivers, thus leading to simplified IIO drivers code.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add resource managed devm_iio_trigger_register() and
devm_iio_triger_unregister() to automatically clean up registered triggers
allocated by IIO drivers, thus leading to simplified IIO drivers code.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here are a number of small driver fixes for 4.8-rc5.
The largest thing here is deleting an obsolete driver,
drivers/misc/bh1780gli.c, as the functionality of it was replaced by an
iio driver a while ago. The other fixes are things that have been
reported, or reverts of broken stuff (the binder change). All of these
changes have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfK3/MPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspm5MAoLb+
VGesoc7cGbFN0EIskollZRzBAJ9Wnhvu3rVeDQYCA0t9+uRg0CcpWw==
=Wt/v
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a number of small driver fixes for 4.8-rc5.
The largest thing here is deleting an obsolete driver,
drivers/misc/bh1780gli.c, as the functionality of it was replaced by
an iio driver a while ago.
The other fixes are things that have been reported, or reverts of
broken stuff (the binder change). All of these changes have been in
linux-next for a while with no reported issues"
* tag 'char-misc-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
thunderbolt: Don't declare Falcon Ridge unsupported
thunderbolt: Add support for INTEL_FALCON_RIDGE_2C controller.
thunderbolt: Fix resume quirk for Falcon Ridge 4C.
lkdtm: Mark lkdtm_rodata_do_nothing() notrace
mei: me: disable driver on SPT SPS firmware
Revert "android: binder: fix dangling pointer comparison"
drivers/iio/light/Kconfig: SENSORS_BH1780 cleanup
android: binder: fix dangling pointer comparison
misc: delete bh1780 driver
All the scaling of the KXSD9 involves multiplication with a
fraction number < 1.
However the scaling value returned from IIO_INFO_SCALE was
unpredictable as only the micros of the value was assigned, and
not the integer part, resulting in scaling like this:
$cat in_accel_scale
-1057462640.011978
Fix this by assigning zero to the integer part.
Cc: stable@vger.kernel.org
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
drivers/iio/chemical/vz89x.c:119:9-10: WARNING: return of 0/1 in function 'vz89x_measurement_is_valid' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
CC: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In at least one known setup, the chip comes up in a state where reading
the chip ID returns garbage unless it's been reset, due to noise on the
wires during system boot.
All supported chips have the same reset method, and based on the
datasheets they all need 1.3 or 1.8ms to recover after reset. So, do
the conservative thing here and always reset the chip.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We were checking the return code of vdd when we should be checking
vdd_io. My mistake, mea culpa.
Cc: Giuseppe BARBA <giuseppe.barba@st.com>
Reported-by: Giuseppe BARBA <giuseppe.barba@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Apex Embedded Systems STX104 features 16 channels of single-ended (8
channels of true differential) 16-bit analog input. Differential input
configuration may be selected via a physical jumper on the device.
Similarly, input polarity (unipolar/bipolar) is configured via a
physical jumper on the device.
Input gain selection is available to the user via software, thus
allowing eight possible input ranges: +-10V, +-5V, +-2.5V, +-1.25V,
0 to 10V, 0 to 5V, 0 to 2.5V, and 0 to 1.25V. Four input gain
configurations are supported: x1, x2, x4, and x8.
This ADC resolution is 16-bits (1/65536 of full scale). Analog input
samples are taken on software trigger; neither FIFO sampling nor
interrupt triggering is supported by this driver.
The Apex Embedded Systems STX104 is primarily an analog-to-digital
converter device. The STX104 IIO driver was initially placed in the DAC
directory because only the DAC portion of the STX104 was supported at
the time. Now that ADC support has been added to the STX104 IIO driver,
the driver should be moved to the more appropriate ADC directory.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
According to IIO ABI definition, IIO_PRESSURE data output unit is
kilopascal:
http://lxr.free-electrons.com/source/Documentation/ABI/testing/sysfs-bus-iio
This patch fix output unit of HID pressure sensor IIO driver from pascal to
kilopascal to follow IIO ABI definition.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
commit 1961bce764 "iio: ina2xx: Remove trace_printk debug
statements" removed the code that used the chip->prev_ns field.
This patch cleans it up further by removing the unused field
and assignments.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are times when an assigned trigger to a device shouldn't ever
change after intialization.
Examples of this being used is when an provider device has a trigger
that is assigned to an ADC, which uses it populate data into a callback
buffer.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This makes sx9500 driver usable on devicetree based platforms too.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Vlad Dogaru <ddvlad@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds Texas Instruments' ADC12130/ADC12132/ADC12138 12-bit plus
sign ADC driver. I have tested with the ADC12138. The ADC12130 and
ADC12132 are not tested but these are similar to ADC12138 except that
the mode programming instruction is a bit different.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Patches merged to the IIO BMP085 driver makes it fully compliant
with all features found in this old misc driver. Retire this old
driver in favor of the new one in the proper subsystem.
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Marek Belisko <marek@goldelico.com>
Acked-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get 2 warnings when biuld kernel with W=1:
drivers/iio/common/st_sensors/st_sensors_trigger.c:69:13: warning: no previous prototype
for 'st_sensors_irq_handler' [-Wmissing-prototypes]
drivers/iio/common/st_sensors/st_sensors_trigger.c:85:13: warning: no previous prototype
for 'st_sensors_irq_thread' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ak8974_configure() function is used only from the PM code,
but that can be hidden when CONFIG_PM is disabled:
drivers/iio/magnetometer/ak8974.c:201:12: error: 'ak8974_configure' defined but not used [-Werror=unused-function]
This replaces the #ifdef with a __maybe_unused annotation, which
will work correctly in all configurations and avoid the warning,
as the compiler can now see where ak8974_configure is called from.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7c94a8b2ee ("iio: magn: add a driver for AK8974")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A small rework of the PM code in this driver introduced a harmless
warning when CONFIG_PM_SLEEP is not set:
drivers/iio/common/hid-sensors/hid-sensor-trigger.c:212:12: error: 'hid_sensor_resume' defined but not used [-Werror=unused-function]
This removes the #ifdef and instead marks all three PM functions
as __maybe_unused, which covers all possible cases and is harder
to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7f6cf74145 ("iio: hid-sensors: use asynchronous resume")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When terminating for_each_child_of_node() iteration with
break or return, of_node_put() should be used to prevent
stale device node references from being left behind.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fixes the following sparse warnings:
drivers/iio/temperature/maxim_thermocouple.c:35:28: warning:
symbol 'max6675_channels' was not declared. Should it be static?
drivers/iio/temperature/maxim_thermocouple.c:52:28: warning:
symbol 'max31855_channels' was not declared. Should it be static?
drivers/iio/temperature/maxim_thermocouple.c:98:38: warning:
symbol 'maxim_thermocouple_chips' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-By: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These sensors all have Vdd and Vdd_IO lines. This means the
supplies are *not* optional (optional means that the supply is
optional in the electrical sense, not the software sense)
so we need to get the and enable them at all times.
If the device tree or board file does not define suitable
regulators for the component, it will be substituted by a
dummy regulator, or, if regulators are disabled altogether,
by stubs. There is no need to use the IS_ERR_OR_NULL() check
that is considered harmful.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Cc: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for Analog Devices AD8801/AD8803, 8 channels 8bits, Digital to
Analog converters.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support the VZ89TE variant which removes the voc_short channel,
and has CRC check for data transactions.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Abstract chip configuration data to allow supporting multiple variants
of the VZ89 chemical sensor line.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adds basic support for the LTC2485 ADC - a delta-sigma analog-to-digital
converter with an I2C interface that operates in single shot conversion
mode.
The driver supports an on board 5V reference and the power-on default
configuration which rejects both 50hz & 60hz line frequencies and
operates in 1x speed mode.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The comparison for devnr limits is off-by-one, the current check
allows 0 to AD5755_NUM_CHANNELS and the limit should be in fact
0 to AD5755_NUM_CHANNELS - 1. This can lead to an out of bounds
write to pdata->dac[devnr]. Fix this by replacing > with >= on the
comparison.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Fixes: c947459979 ("iio: ad5755: add support for dt bindings")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Device support
* ak8974
- New driver and bindings for this 2009 vintage magnetometer (it was very
popular back then!)
* atlas-ph-sensor
- ORP sensor support(I had to look up what one of these was)
* cio-dac
- New driver for Measurement Computing DAC boards
* dmard06
- New driver for Domintech DMARDO6 accelerometer. Also vendor prefix.
* dmard09
- New driver for Domintech DMARD09 accelerometer.
* maxim-thermocouple
- max6675 and max31855 new driver
* mt6577 auxdac
- new driver for this Mediatek chip mt2701, mt6577 and mt8173 have this
hardware.
* ti-adc161s626
- new driver for this TI single channel differential ADC.
* vcnl4000
- support vcnl4010 and vcnl4020 which are compatible for all features
currently supported by this driver.
New features
* Core
- Allow retrieving of underlying iio_dev from a callback buffer handle.
This is needed to allow client drivers to perform operations such as
configuring the trigger used.
* hid-sensors
- asynchronous resume support to avoid really long resume times.
* kxcjk-1013
- add the mysterious KIOX000A ACPI id seen in the wild.
* Tools
- lsiio now enumerates processed as well as raw channels.
Cleanup
* ad7298
- use iio_device_claim_direct_mode and friends to simplify locking around
mode switching and drop some boilerplate.
* ad7793
- use iio_device_claim_direct_mode and friends to simplify locking around
mode switching and drop some boilerplate.
* ade7854
- checkpatch fixups (alignment of parameters)
* atlas-ph-sensor
- use iio_device_claim_direct_mode and friends to simplify locking around
mode switching and drop some boilerplate.
- Switch to REGCACHE_NONE as there are no useful register to cache.
* bma180
- use iio_device_claim_direct_mode and friends to simplify locking around
mode switching and drop some boilerplate.
* hdc100x
- Add mention of the HDC1000 and HDC1008 to the Kconfig help text.
* isl29018
- Add driver specific prefixes to defines and function names.
- Remove excessive logging.
- Drop newlines which add nothing to readability.
- General tidying up of comments.
- Drop I2C_CLASS_HWMON as irrelevant to driver.
* isl29028
- Add driver specific prefixes to defines, enums and function names.
- Drop comma's from available attribute output as not ABI compliant.
- Drop I2C_CLASS_HWMON as irrelevant to driver.
* kxsd9
- devicetree bindings.
* mag3110
- This one wasn't locking to protect against mode switches during
raw_reads. Use the iio_claim_direct_mode function to fix this buglet.
* maxim-theromcouple
- Fix missing selects for triggered buffer support in Kconfig.
* nau7802
- Use complete instead of complete_all as only one completion at a time.
* sx9500
- Use complete instead of complete_all as only one completion at a time.
* us5182d
- Add a missing error code asignment instead of checking the result of
an already checked statement.
* vcnl4000
- Use BIT macro where appropriate.
- Refactor return codes in read_raw callback.
- Add some missing locking for concurrent accesses to the device.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=d6Kh
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.9a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into work-testing
Jonathan writes:
First round of new features, device support and cleanups for IIO in the 4.9 cycle.
Device support
* ak8974
- New driver and bindings for this 2009 vintage magnetometer (it was very
popular back then!)
* atlas-ph-sensor
- ORP sensor support(I had to look up what one of these was)
* cio-dac
- New driver for Measurement Computing DAC boards
* dmard06
- New driver for Domintech DMARDO6 accelerometer. Also vendor prefix.
* dmard09
- New driver for Domintech DMARD09 accelerometer.
* maxim-thermocouple
- max6675 and max31855 new driver
* mt6577 auxdac
- new driver for this Mediatek chip mt2701, mt6577 and mt8173 have this
hardware.
* ti-adc161s626
- new driver for this TI single channel differential ADC.
* vcnl4000
- support vcnl4010 and vcnl4020 which are compatible for all features
currently supported by this driver.
New features
* Core
- Allow retrieving of underlying iio_dev from a callback buffer handle.
This is needed to allow client drivers to perform operations such as
configuring the trigger used.
* hid-sensors
- asynchronous resume support to avoid really long resume times.
* kxcjk-1013
- add the mysterious KIOX000A ACPI id seen in the wild.
* Tools
- lsiio now enumerates processed as well as raw channels.
Cleanup
* ad7298
- use iio_device_claim_direct_mode and friends to simplify locking around
mode switching and drop some boilerplate.
* ad7793
- use iio_device_claim_direct_mode and friends to simplify locking around
mode switching and drop some boilerplate.
* ade7854
- checkpatch fixups (alignment of parameters)
* atlas-ph-sensor
- use iio_device_claim_direct_mode and friends to simplify locking around
mode switching and drop some boilerplate.
- Switch to REGCACHE_NONE as there are no useful register to cache.
* bma180
- use iio_device_claim_direct_mode and friends to simplify locking around
mode switching and drop some boilerplate.
* hdc100x
- Add mention of the HDC1000 and HDC1008 to the Kconfig help text.
* isl29018
- Add driver specific prefixes to defines and function names.
- Remove excessive logging.
- Drop newlines which add nothing to readability.
- General tidying up of comments.
- Drop I2C_CLASS_HWMON as irrelevant to driver.
* isl29028
- Add driver specific prefixes to defines, enums and function names.
- Drop comma's from available attribute output as not ABI compliant.
- Drop I2C_CLASS_HWMON as irrelevant to driver.
* kxsd9
- devicetree bindings.
* mag3110
- This one wasn't locking to protect against mode switches during
raw_reads. Use the iio_claim_direct_mode function to fix this buglet.
* maxim-theromcouple
- Fix missing selects for triggered buffer support in Kconfig.
* nau7802
- Use complete instead of complete_all as only one completion at a time.
* sx9500
- Use complete instead of complete_all as only one completion at a time.
* us5182d
- Add a missing error code asignment instead of checking the result of
an already checked statement.
* vcnl4000
- Use BIT macro where appropriate.
- Refactor return codes in read_raw callback.
- Add some missing locking for concurrent accesses to the device.
SARADC controller needs to be reset before programming it, otherwise
it will not function properly.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-iio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Any readings from the raw interface of the KXSD9 driver will
return an empty string, because it does not return
IIO_VAL_INT but rather some random value from the accelerometer
to the caller.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some platforms power off sensor hubs during S3 suspend, which will require
longer time to resume. This hurts system resume time, so resume
asynchronously.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add Mediatek auxadc driver based on iio.
It will register a device in iio and support iio.
So thermal can read auxadc channel to sample data by iio device.
It is tested successfully on mt2701 platform.
Mt8173 and mt6577 platforms are not tested.
But the expectation is compatible.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Select IIO_BUFFER and IIO_TRIGGERED_BUFFER to compile maxim_thermocouple.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Now that open delay and sample delay for each channel is configurable
via DT, the default IDLE_TIMEOUT value is not enough as this is
calculated based on hardcoded macros. This results in driver returning
EBUSY sometimes. Fix this by increasing the timeout
value based on maximum value possible to open delay and sample delays
for each channel.
Fixes: 5dc11e8106 ("iio: adc: ti_am335x_adc: make sample delay, open delay, averaging DT parameters")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It is possible that two or more ADC channels can be simultaneously
requested for raw samples, in which case there can be race in access to
FIFO data resulting in loss of samples.
If am335x_tsc_se_set_once() is called again from tiadc_read_raw(), when
ADC is still acquired to sample one of the channels, the second process
might be put into uninterruptible sleep state. Fix these issues, by
protecting FIFO access and channel configurations with a mutex. Since
tiadc_read_raw() might take anywhere between few microseconds to few
milliseconds to finish execution (depending on averaging and delay
values supplied via DT), its better to use mutex instead of spinlock.
Fixes: 7ca6740cd1 ("mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during raw reads.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix an incorrect assignment due to a typo on a variable name. The
variable val2 should be assigned 100000 and not val.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-By: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When using CONFIG_DEBUG_ATOMIC_SLEEP, the scheduler nicely points out
that we're calling sleeping primitives within the wait_event loop, which
means we might clobber the task state:
[ 10.831289] do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffc00026b610>]
[ 10.845531] ------------[ cut here ]------------
[ 10.850161] WARNING: at kernel/sched/core.c:7630
...
[ 12.164333] ---[ end trace 45409966a9a76438 ]---
[ 12.168942] Call trace:
[ 12.171391] [<ffffffc00024ed44>] __might_sleep+0x64/0x90
[ 12.176699] [<ffffffc000954774>] mutex_lock_nested+0x50/0x3fc
[ 12.182440] [<ffffffc0007b9424>] iio_kfifo_buf_data_available+0x28/0x4c
[ 12.189043] [<ffffffc0007b76ac>] iio_buffer_ready+0x60/0xe0
[ 12.194608] [<ffffffc0007b7834>] iio_buffer_read_first_n_outer+0x108/0x1a8
[ 12.201474] [<ffffffc000370d48>] __vfs_read+0x58/0x114
[ 12.206606] [<ffffffc000371740>] vfs_read+0x94/0x118
[ 12.211564] [<ffffffc0003720f8>] SyS_read+0x64/0xb4
[ 12.216436] [<ffffffc000203cb4>] el0_svc_naked+0x24/0x28
To avoid this, we should (a la https://lwn.net/Articles/628628/) use the
wait_woken() function, which avoids the nested sleeping while still
handling races between waiting / wake-events.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org> # 3.19+ for introduction of wake_woken
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since there are overlapping volatile regions between parts, and only
register that isn't volatile is the temperature compensation provided
from userspace.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for Texas Instruments ADC141S626, and ADC161S626 chips.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add iio_channel_cb_get_iio_dev function to allow getting the
underlying iio_dev. This is useful for setting the trigger of the
consumer ADC device.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The call to i2c_get_clientdata(client) returns a struct iio_dev*, not
the needed struct ads1015_data*. We need here an intermediate step as
in the function: void ads1015_get_channels_config(struct i2c_client *client).
Signed-off-by: Giorgio Dal Molin <giorgio.nicole@arcor.de>
Fixes: ecc24e72f4 ("iio: adc: Add TI ADS1015 ADC driver support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation of an IIO driver for the Domintech DMARD09 3-axis
accelerometer. Only supports reading the x,y,z axes at the moment.
Implementation based on the Android driver from the Acer Liquid E2
kernel sources.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch add support for Domintech DMARD05, DMARD06 and DMARD07
accelerometers.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit 7ef9153d9a ("misc: delete bh1780 driver") has removed the
Kconfig option SENSORS_BH1780. Remove the last reference on this
option.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
waiter context waker context
sx9500_read_proximity()
sx9500_inc_chan_users()
sx9500_inc_data_rdy_users()
wait_for_completion_interruptible()
s9500_irq_thread_handler()
complete()
reinit_completion()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
waiter context waker context
nau7802_read_irq()
reinit_completion()
nau7802_read_conversion()
wait_for_completion_interruptible_timeout()
nau7802_eoc_trigger()
complete()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver always assumes that an input device has been created when
reading channel 3. This causes a kernel panic when dereferencing
st->ts_input.
The change was introduced in
commit 84882b0603 ("iio: adc: at91_adc: Add support for touchscreens
without TSMR"). Earlier versions only entered that part of the if-else
statement if only the following flags are set:
AT91_ADC_IER_XRDY | AT91_ADC_IER_YRDY | AT91_ADC_IER_PRDY
Signed-off-by: Anders Darander <anders@chargestorm.se>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
hdc100x supports Texas Instruments HDC1000 and HDC1008 relative
humidity and temperature sensors. Add these product names to
Kconfig.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the i2c_smbus_read_byte commmands used to retrieve the sensor
data with an i2c_master_recv command.
The smbus read byte method fails because the device does not expect a
stop condition after sending the first byte. When we issue the second
read, we are getting the first byte again. Net effect is that of the 14
bits used for the measurement, the 8 most significant bits are correct,
the lower 6 are not.
None of the smbus read protocols follow the pattern this device requires
(S Addr Rd [A] Data [A] Data NA P), hence the switch to an i2c receive
transaction.
Applicable from original introduction of this driver, but will require
backporting due to churn in the code.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It is likely that checking the result of 'pm_runtime_set_active' is
expected here.
Fixes: f0e5f57d3a ("iio: light: us8152d: Add power management support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds a driver for the Asahi Kasei AK8974 and its sibling
AMI305 magnetometers. It was deployed on scale in 2009 on a
multitude of devices. It is distincly different from AK8973
and AK8975 and needs its own driver.
This patch is based on the long lost work of Samu Onkalo at Nokia,
who made a misc character device driver for the Maemo/MeeGo Nokia
devices, before the time of the IIO subsystem. It was mounted in e.g.
the Nokia N950, N8, N86, N97 etc. It is also mounted on the
ST-Ericsson HREF reference designs.
It works nicely in sysfs:
$ cat in_magn_x_raw && cat in_magn_y_raw && cat in_magn_z_raw
-55
-101
161
And with buffered reads using a simple HRTimer trigger:
$ generic_buffer -c10 -a -n ak8974 -t foo
iio device number being used is 3
iio trigger number being used is 2
No channels are enabled, enabling all channels
Enabling: in_magn_x_en
Enabling: in_magn_y_en
Enabling: in_magn_z_en
Enabling: in_timestamp_en
/sys/bus/iio/devices/iio:device3 foo
-58.000000 -102.000000 157.000000 946684970985321044
-60.000000 -98.000000 159.000000 946684971012237548
-60.000000 -106.000000 163.000000 946684971032257080
-62.000000 -94.000000 169.000000 946684971052185058
-58.000000 -98.000000 163.000000 946684971072204589
-54.000000 -100.000000 163.000000 946684971092224121
-53.000000 -103.000000 164.000000 946684971112731933
-50.000000 -102.000000 165.000000 946684971132232666
-61.000000 -101.000000 164.000000 946684971152191162
-57.000000 -99.000000 168.000000 946684971172210693
Disabling: in_magn_x_en
Disabling: in_magn_y_en
Disabling: in_magn_z_en
Disabling: in_timestamp_en
I cannot currently scale these raw values to gauss. This is
because of lack of documentation. I have sent a request for
a datasheet to Asahi Kasei.
The driver can optionally use a DRDY line IRQ to capture data,
else it will sleep and poll.
Cc: Samu Onkalo <samu.onkalo@intel.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In commit 3d838118c6 ("iio: pressure: bmp280: add power management")
For some reason the code in the runtime suspend/resume hooks
got wrong (I suspect in the ambition to cut down boilerplate)
and it seems it was tested without CONFIG_PM and crashes like
so for me:
Unable to handle kernel NULL pointer dereference at virtual address 0000000c
pgd = c0204000
[0000000c] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 PID: 89 Comm: kworker/1:2 Not tainted
4.7.0-03348-g90dc3680458a-dirty #99
Hardware name: Generic DT based system
Workqueue: pm pm_runtime_work
task: df3c6300 ti: dec8a000 task.ti: dec8a000
PC is at regulator_disable+0x0/0x6c
LR is at bmp280_runtime_suspend+0x3c/0xa4
Dereferencing the BMP280 state container properly fixes the problem,
sorry for screwing up.
Fixes: 3d838118c6 ("iio: pressure: bmp280: add power management")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Select IIO_BUFFER and IIO_TRIGGERED_BUFFER to compile.
Remove IIO_TRIGGER if present since IIO_BUFFER selects it.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The devm_iio_device_register function should not be used if custom
operations must be performed in the remove callback. This patch replaces
the dem_iio_device_register call with a iio_device_register call and
respective iio_device_unregister call in the remove callback.
Fixes: 765550e4d9 ("iio: stx104: Add GPIO support for the Apex Embedded Systems STX104")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the iio_pollfunc_store_time parameter during triggered buffer
set-up to get valid timestamps.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the iio_pollfunc_store_time parameter during triggered buffer
set-up to get valid timestamps.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-By: Tiberiu Breana <tiberiu.a.breana@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the iio_pollfunc_store_time parameter during triggered buffer
set-up to get valid timestamps.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-By: Tiberiu Breana <tiberiu.a.breana@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The data buffer for captured mode for the ad799x driver is allocated in the
update_scan_mode() callback. This callback is not set in the iio_info
struct for the ad7791/ad7995/ad7999, which means that the data buffer is
not allocated when a captured transfer is started. As a result the driver
crashes when the first sample is received. To fix this properly set the
update_scan_mode() callback.
Fixes: d8dca33027 ("staging:iio:ad799x: Preallocate sample buffer")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
PTR_ERR should access the value just tested by IS_ERR, otherwise
the wrong error code will be returned.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Measurement Computing CIO-DAC is a family of 16-bit and 12-bit
analog output devices. The analog outputs are from AD660BN/AD7237
converters with each output buffered by an OP-27. Voltage ranges are
configured via physical jumpers on the device.
This driver does not support the devices' simulataneous update mode; the
XFER jumper option should be deselected for all analog output channels.
This driver provides IIO support for the Measurement Computing CIO-DAC
family: CIO-DAC16, CIO-DAC08, and PC104-DAC06. The base port addresses
for the devices may be configured via the base array module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On the Cube i9 tablet, the ACPI id for the Kionix kxcj9 accelerometer is
"KIOX000A" (as can be seen in the DSDT of the Cube i9 tablet).
It is the same accelerometer, so only adding the ACPI id is needed.
Signed-off-by: Christophe Chapuis <chris.chapuis@gmail.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New core features
- Selection of the clock source for IIO timestamps. This is done per device
as it makes little sense to have events in one timebase and data timestamped
on another. Biggest reason for this is that we currently use a clock
source which is non monotonic which can result in 'interesting' data sets.
(Includes export for get_monotonic_corse64 which Thomas Gleixner didn't mind
in an earlier version.)
- MAINTAINERS add the git tree to the list for IIO.
New device support + a kind of indirect staging graduation.
* Broadcom iproc-static-adc
- new driver
* mcp4531
- support for MCP454x, MCP456x, MCP464x and MCP466x potentiometers
* mpu6050
- support the IC20608 6 axis motion tracking device
* st-sensors
- support the lis3l02dq + drop the lis3l02dq driver from staging.
The general purpose driver is missing event support, but good to get
rid of this driver which was rather long in the tooth.
New driver features
* ak8975
- Add vid regulator support and refactor handling in general.
- Allow a delay after enabling regulators.
- Runtime and system PM.
* bmg160
- filter frequency control support.
* bmp280
- SPI device support.
- EOC interrupt support for the BMP085
- power management support.
- supply regulator support.
- reset gpio support
- dt bindings for reset gpio and regulators.
- of table to support device tree registration
* max1363
- Device tree bindings.
* mcp4531
- Device tree bindings.
* st-pressure
- temperature channels as part of triggered buffer (previously not due
probably to alignment issues - see below).
- lps22hb open drain interrupt support.
- lps22hb temperature channel support
Cleanups and reworkings.
* numerous ADC drivers
- ensure the iio_dev->dev.of_node is set to the parent dev.of_node so
as to allow client bindings to find the device.
* ak8975
- Fix incorrect handling of missing regulator
- make sure power is down and remove.
* bmp280
- read the calibration data only once as it doesn't change.
* isl29125
- Use a few macros to make code a touch more readable.
* mma8452
- fix a memory leak on error.
- drop an unecessary bit of return value handling.
* potentiometer kconfig
- typo fix.
* st-pressure
- drop some uninformative default assignments of elements of the channel
array structure (aids readability).
* st-sensors
- Harden interrupt handling considerably. These are actually all using
level interrupts, but at least two known boards have them wired to
edge only interrupt chips. Hence a slightly interesting bit of handling
is needed in which we first allow for the easy option (level triggered) and
secondly check the status registers before reenabling edge interrupts and
fall back to a tight loop in the thread until we successfully clear the
interrupt. No harm is done if we never succeed in doing so. It's an odd
patch that has been through a lot of revisions to reach a consensus on how
to handle what is basically broken hardware (which the previous defaults
allowed to kind of work).
- Fix alignment to defined storagebytes boundaries.
- Ensure alignment of power of 2 byte boundaries. This has always in theory
been part of the ABI of IIO, but we missed a few that snuck in that need
fixing. The effect was minor as they were only followed by timestamp
channels which were correctly aligned,
- Add some docs to explain the gain calculations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=FxNN
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of IIO new device support, features and cleanups for the 4.8 cycle.
New core features
- Selection of the clock source for IIO timestamps. This is done per device
as it makes little sense to have events in one timebase and data timestamped
on another. Biggest reason for this is that we currently use a clock
source which is non monotonic which can result in 'interesting' data sets.
(Includes export for get_monotonic_corse64 which Thomas Gleixner didn't mind
in an earlier version.)
- MAINTAINERS add the git tree to the list for IIO.
New device support + a kind of indirect staging graduation.
* Broadcom iproc-static-adc
- new driver
* mcp4531
- support for MCP454x, MCP456x, MCP464x and MCP466x potentiometers
* mpu6050
- support the IC20608 6 axis motion tracking device
* st-sensors
- support the lis3l02dq + drop the lis3l02dq driver from staging.
The general purpose driver is missing event support, but good to get
rid of this driver which was rather long in the tooth.
New driver features
* ak8975
- Add vid regulator support and refactor handling in general.
- Allow a delay after enabling regulators.
- Runtime and system PM.
* bmg160
- filter frequency control support.
* bmp280
- SPI device support.
- EOC interrupt support for the BMP085
- power management support.
- supply regulator support.
- reset gpio support
- dt bindings for reset gpio and regulators.
- of table to support device tree registration
* max1363
- Device tree bindings.
* mcp4531
- Device tree bindings.
* st-pressure
- temperature channels as part of triggered buffer (previously not due
probably to alignment issues - see below).
- lps22hb open drain interrupt support.
- lps22hb temperature channel support
Cleanups and reworkings.
* numerous ADC drivers
- ensure the iio_dev->dev.of_node is set to the parent dev.of_node so
as to allow client bindings to find the device.
* ak8975
- Fix incorrect handling of missing regulator
- make sure power is down and remove.
* bmp280
- read the calibration data only once as it doesn't change.
* isl29125
- Use a few macros to make code a touch more readable.
* mma8452
- fix a memory leak on error.
- drop an unecessary bit of return value handling.
* potentiometer kconfig
- typo fix.
* st-pressure
- drop some uninformative default assignments of elements of the channel
array structure (aids readability).
* st-sensors
- Harden interrupt handling considerably. These are actually all using
level interrupts, but at least two known boards have them wired to
edge only interrupt chips. Hence a slightly interesting bit of handling
is needed in which we first allow for the easy option (level triggered) and
secondly check the status registers before reenabling edge interrupts and
fall back to a tight loop in the thread until we successfully clear the
interrupt. No harm is done if we never succeed in doing so. It's an odd
patch that has been through a lot of revisions to reach a consensus on how
to handle what is basically broken hardware (which the previous defaults
allowed to kind of work).
- Fix alignment to defined storagebytes boundaries.
- Ensure alignment of power of 2 byte boundaries. This has always in theory
been part of the ABI of IIO, but we missed a few that snuck in that need
fixing. The effect was minor as they were only followed by timestamp
channels which were correctly aligned,
- Add some docs to explain the gain calculations.
VCNL4000, VCNL4010 and VCNL4020 chips are fairly compatible from a software
point of view, added features are not yet supported by the driver
patch adds a check for the product ID and demotes the corresponding
dev_info() to dev_dbg()
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add initial driver support for MAX6675, and MAX31855 thermocouple chips.
Cc: Marek Vasut <marex@denx.de>
Cc: Matt Porter <mporter@konsulko.com>
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Removed unwanted return statements from the function
mma8452_set_freefall_mode.
Signed-off-by: Bijosh Thykkoottathil <bijosh.t@hotmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mma8452_set_freefall_mode can return -ve value in case if
i2c_smbus_read_byte_data fails. This function is called from mma8452_probe,
and returning -ve value from probe indicates probe failure. Need to call
iio_triggered_buffer_cleanup & iio_trigger_cleanup in this case.
Signed-off-by: Bijosh Thykkoottathil <bijosh.t@hotmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some static channels are explicitly initialized with default values.
Remove them to enhance readability.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable support for triggered buffering of temperature samples.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Details scaling factors and offsets applied to raw temperature and pressure
samples.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Sampled pressure data are 24 bits long and should be stored in a 32 bits
word.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure triggered buffering memory accesses are properly aligned on per
channel storagebits boundaries.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Time to finally kill off the venerable (it was one of my first drivers)
lis3l02dq driver in favour of adding support in the st sensors framework.
This does loose us the event support that driver always had, but I think
that will reappear at some point and in the meantime the maintenance
advantages of dropping the 'special' driver for this one part outweigh
the issues.
It's worth noting this part is ancient and I may well be the only person
who still has any on hardware running recent kernels.
It has a few 'quirks'.
- No WAI register so that just became optional.
- A BDU option that really does block updates. Completely.
Whatever you do, you don't get any more data with it set.
It is documented the same as more modern parts but I presume they
are actually clearing for updates after a read of both bytes!
- Fixed scale.
- It's too quick. Even at slowest rate (280Hz) I can't read out fast
enough on my board (stargate 2) to beat new data coming in. Linus'
repeat read patch doesn't help in this case. It just means I get 10
readings before dying... So in reality this will get used with
software triggers only unless someone has this long out of production
device on a quick board.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Cc: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adding missing indio_dev->dev.of_node references to allow iio consumers
to access the device channels.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add the pointer to the device tree node of the ADC so that iio
consumers can reference the respective channels.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds the necessary device tree binding to allow DT probing of
currently supported parts.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for MCP454x, MCP456x, MCP464x and MCP466x parts.
The main difference with currently supported parts (MCP453x and alike) is
the addition of a non-volatile memory in order to recall the wiper setting
at power-on. This feature is currently not supported and only the
volatile memory is used to set the wiper.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Introduce support for Invense ICM20608 IMU, a 6-axis motion tracking device
that combines a 3-axis gyroscope and a 3-axis accelerometer:
http://www.invensense.com/products/motion-tracking/6-axis/icm-20608-2
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds the necessary device tree binding to allow DT probing of
currently supported parts.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The filter frequency and sample rate have a fixed relationship.
Only the filter frequency is unique, however.
Currently the driver ignores the filter settings for 32 Hz and
64 Hz.
This patch adds the necessary callbacks to be able to configure
and read the filter setting from sysfs.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds basic driver implementation for Broadcom's
static adc controller used in iProc SoC's family.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The calibration data is described as coming from an E2PROM and that
means it does not change. Just read it once at probe time and store
it in the device state container. Also toss the calibration data
into the entropy pool since it is device unique.
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The PM280 has an internal standby-mode, but to really save power
we should shut the sensor down and disconnect the power. With
the proper .pm hooks we can enable both runtime and system power
management of the sensor. We use the *force callbacks from the
system PM hooks. When the sensor comes back we always reconfigure
it to make sure it is ready to roll as expected.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The first version of this sensor, BMP085, supports sending an
End-of-Conversion (EOC) interrupt. Add code to support this using
a completion, in a similar vein as drivers/misc/bmp085.c does.
Make sure to check that we are given a rising edge, because the
EOC line goes from low-to-high when the conversion is ready.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch mimics the SPI functionality found in the misc driver in
drivers/misc/bh085-spi.c to make it possible to reuse the existing
BMP280/BMP180/BMP085 driver with all clients of the other driver.
The adoption is straight-forward since like the other driver, it is
a simple matter of using regmap.
This driver is also so obviously inspired/copied from the old misc
driver in drivers/misc/bmp085.c that I just took the liberty to
add in the authors of the other drivers + self in the core driver
file.
The MISC driver also supports a variant named "BMP181" so include
that here to be complete in comparison to the old driver.
The bus mapping code for SPI was written by Akinobu Mita.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This creates a separate BMP280_I2C Kconfig entry that gets selected
by BMP280 for I2C transport. As we currently only support I2C
transport there is not much practical change other than getting
a separate object file (or module) for the I2C driver part. The
old Kconfig symbol BMP280 will still select the stuff we need so
that oldconfig and old defconfigs works fine.
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This splits the BMP280 driver in three logical parts: the core driver
bmp280-core that only operated on a struct device * and a struct regmap *,
the regmap driver bmp280-regmap that can be shared between I2C and other
transports and the I2C module driver bmp280-i2c.
Cleverly bake all functionality into a single object bmp280.o so that
we still get the same module binary built for the device in the end,
without any fuzz exporting symbols to the left and right.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The BMP085/BMP180/BMP280 is supplied with two power sources:
VDDA (analog power) and VDDD (digital power). As these may come
from regulators (as on the APQ8060 Dragonboard) we need the driver
to attempt to fetch and enable these regulators.
We FAIL if we cannot: boards should either define:
- Proper regulators if present
- Define fixed regulators if power is hardwired to the component
- Rely on dummy regulators (will be present on all DT systems and
any boardfile system that calls regulator_has_full_constraints().
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added macros for sensing range as the corresponding magic numbers
were used at multiple places.
- ISL29125_SENSING_RANGE_0 for 375 lux full range
- ISL29125_SENSING_RANGE_1 for 10k lux full range
Signed-off-by: Bijosh Thykkoottathil <bijosh.t@hotmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Leonard Crestez observed the following phenomenon: when using
hard interrupt triggers (the DRDY line coming out of an ST
sensor) sometimes a new value would arrive while reading the
previous value, due to latencies in the system.
We discovered that the ST hardware as far as can be observed
is designed for level interrupts: the DRDY line will be held
asserted as long as there are new values coming. The interrupt
handler should be re-entered until we're out of values to
handle from the sensor.
If interrupts were handled as occurring on the edges (usually
low-to-high) new values could appear and the line be held
asserted after that, and these values would be missed, the
interrupt handler would also lock up as new data was
available, but as no new edges occurs on the DRDY signal,
nothing happens: the edge detector only detects edges.
To counter this, do the following:
- Accept interrupt lines to be flagged as level interrupts
using IRQF_TRIGGER_HIGH and IRQF_TRIGGER_LOW. If the line
is marked like this (in the device tree node or ACPI
table or similar) it will be utilized as a level IRQ.
We mark the line with IRQF_ONESHOT and mask the IRQ
while processing a sample, then the top half will be
entered again if new values are available.
- If we are flagged as using edge interrupts with
IRQF_TRIGGER_RISING or IRQF_TRIGGER_FALLING: remove
IRQF_ONESHOT so that the interrupt line is not
masked while running the thread part of the interrupt.
This way we will never miss an interrupt, then introduce
a loop that polls the data ready registers repeatedly
until no new samples are available, then exit the
interrupt handler. This way we know no new values are
available when the interrupt handler exits and
new (edge) interrupts will be triggered when data arrives.
Take some extra care to update the timestamp in the poll
loop if this happens. The timestamp will not be 100%
perfect, but it will at least be closer to the actual
events. Usually the extra poll loop will handle the new
samples, but once in a blue moon, we get a new IRQ
while exiting the loop, before returning from the
thread IRQ bottom half with IRQ_HANDLED. On these rare
occasions, the removal of IRQF_ONESHOT means the
interrupt will immediately fire again.
- If no interrupt type is indicated from the DT/ACPI,
choose IRQF_TRIGGER_RISING as default, as this is necessary
for legacy boards.
Tested successfully on the LIS331DL and L3G4200D by setting
sampling frequency to 400Hz/800Hz and stressing the system:
extra reads in the threaded interrupt handler occurs.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Tested-by: Crestez Dan Leonard <cdleonard@gmail.com>
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds runtime PM support to the AK8975 driver. It solves two
problems:
- After reading the first value the chip was left in MODE_ONCE,
meaning (presumably) it may be consuming more power. Now the
runtime PM hooks kick in and set it to POWER_DOWN.
- Regulators were simply enabled and left on, making it
impossible to turn the power consuming regulators off because
of the increased refcount. We now disable the regulators at
autosuspend.
- We also handle system suspend: by using pm_runtime_force_suspend()
and pm_runtime_force_resume() from the system PM sleep hooks,
the runtime PM code is managing the power also for this case.
It is currently not completely optimal: when the system resumes
the AK8975 goes into active mode even if noone is going to use
it: currently the force calls need to be paired, but the runtime
PM people are working on making it possible to leave devices
runtime suspended when coming back from sleep.
Inspired by my work on the BH1780 light sensor driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The code was not powering the magnetometer down properly at
remove(): just cutting the regulators without first setting the
device in power off mode. Fix this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The datasheet actually specifies that we need to wait atleast
500us after powering on the device before trying to set mode.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move the regulator_get() calls directly into the probe() function,
keep only the power_on()/power_off() functions to flick the
regulators on/off.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The AK8975 has two power sources: Vdd (analog voltage supply)
and Vid (digital voltage supply). Optionally also obtain the Vid
supply regulator and enable it.
If an error occurs when enabling one of the regulators: bail out.
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Cc: Richard Leitner <dev@g0hl1n.net>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IS_ERR_OR_NULL() should never be used with regulators because
a NULL pointer may be a perfectly valid dummy regulator
We should always succeed to fetch and enable a regulator, but
it may be a dummy. That is fine, so bail out for any real
errors or probe deferrals
Include the error code in the warning print so we know what
kind of problem we're dealing with (for example it is nice to
see if it is a probe deferral).
As we will bail out of probe if the regulator is erroneous,
just issue regulator_disable() on the poweroff path: it will
succeed.
Cc: Mark Brown <broonie@kernel.org>
Cc: Lars-Peter Clausen Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On the APQ8060 Dragonboard the reset line to the BMP085 pressure
sensor is not deasserted on boot, so the driver needs to handle
this. For a simple GPIO line supplied as a descriptor (from a board
file, device tree or ACPI) this does the trick.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds device tree support to the BMP085, BMP180 and BMP280
pressure sensors. Tested on the Qualcomm APQ8060 Dragonboard:
iio:device1$ cat in_temp_input
26700
iio:device1$ cat in_pressure_input
99.185000000
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adds a new per-device sysfs attribute "current_timestamp_clock" to allow
userspace to select a particular POSIX clock for buffered samples and
events timestamping.
Following clocks, as listed in clock_gettime(2), are supported:
CLOCK_REALTIME, CLOCK_MONOTONIC, CLOCK_MONOTONIC_RAW,
CLOCK_REALTIME_COARSE, CLOCK_MONOTONIC_COARSE, CLOCK_BOOTTIME and
CLOCK_TAI.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Firstly some contact detail updates:
* NXP took over freescale. Update the mma8452 header to reflect this.
* Martin Kepplinger email address change in mma8452 header.
* Adriana Reus has changed email address. Update .mailmap.
* Matt Ranostay has changed email address. Update .mailmap.
New Device Support
* max1363
- add the missing i2c_device_ids for a couple of parts so they can actually
be used.
* ms5867
- add device ids for ms5805 and ms5837 parts.
New Features
* ad5755
- DT support. This one was a bit controversial and under review for a long
time. Still no one could come up with a better solution.
* stx104
- add gpio support
* ti-adc081c
- Add ACPI device ID matching.
Core changes
* Refuse to register triggers with duplicate names. There is no way to
distinguish between them so this makes no sense. A few drivers do not
generate unique names for each instance of the device present. We can't
fix this without changing ABI so leave them and wait for someone to
actually take the rare step of two identical accelerometers on the same
board.
* buffer-dma
- use ARRAY_SIZE in a few appropriate locations.
Tools
* Fix the fact that the --trigger-num option in generic_buffer didn't allow
0 which is perfectly valid in the ABI.
Cleanups
* as3935
- improve error reporting.
- remove redundant zeroing of a field in iio_priv.
* gp2ap020a00f
- use the iio_device_claim_*_mode helpers rather than open coding locking
around mode changes.
* isl29125
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* lidar
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* mma8452
- more detail in devices supported description in comments (addresses and
similar)
* sca3000
- add a missing error check.
* tcs3414
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* tcs3472
- use the iio_device_claim_*_mode helpers rather than open coding locking.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6Lja
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second round of new iio device support, features and cleanups in the 4.8 cycle
Firstly some contact detail updates:
* NXP took over freescale. Update the mma8452 header to reflect this.
* Martin Kepplinger email address change in mma8452 header.
* Adriana Reus has changed email address. Update .mailmap.
* Matt Ranostay has changed email address. Update .mailmap.
New Device Support
* max1363
- add the missing i2c_device_ids for a couple of parts so they can actually
be used.
* ms5867
- add device ids for ms5805 and ms5837 parts.
New Features
* ad5755
- DT support. This one was a bit controversial and under review for a long
time. Still no one could come up with a better solution.
* stx104
- add gpio support
* ti-adc081c
- Add ACPI device ID matching.
Core changes
* Refuse to register triggers with duplicate names. There is no way to
distinguish between them so this makes no sense. A few drivers do not
generate unique names for each instance of the device present. We can't
fix this without changing ABI so leave them and wait for someone to
actually take the rare step of two identical accelerometers on the same
board.
* buffer-dma
- use ARRAY_SIZE in a few appropriate locations.
Tools
* Fix the fact that the --trigger-num option in generic_buffer didn't allow
0 which is perfectly valid in the ABI.
Cleanups
* as3935
- improve error reporting.
- remove redundant zeroing of a field in iio_priv.
* gp2ap020a00f
- use the iio_device_claim_*_mode helpers rather than open coding locking
around mode changes.
* isl29125
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* lidar
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* mma8452
- more detail in devices supported description in comments (addresses and
similar)
* sca3000
- add a missing error check.
* tcs3414
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* tcs3472
- use the iio_device_claim_*_mode helpers rather than open coding locking.
Use the ARRAY_SIZE macro in the for loops that access queue->fileio.blocks.
Macro is already used in a couple of places where this access occurs,
but range was hardcoded in these locations.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver supports MAX11644, MAX11645, MAX11646 and MAX11647 parts. But
the corresponding i2c_device_id are missing. Add them!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is redundant as the containing stucture is allocated as part of
iio_device_alloc using kzalloc and hence is already 0.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Apex Embedded Systems STX104 device features eight lines of digital
I/O (four digital inputs and four digital outputs). This patch adds GPIO
support for these eight lines of digital I/O via GPIOLIB.
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
gcc warns about a potentially uninitialized variable use
in as3935_event_work:
drivers/iio/proximity/as3935.c: In function ‘as3935_event_work’:
drivers/iio/proximity/as3935.c:231:6: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This case specifically happens when spi_w8r8() fails with a
negative return code. We check all other users of this function
except this one.
As the error is rather unlikely to happen after the device
has already been initialized, this just adds a dev_warn().
Another warning already exists in the same function, but is
missing a trailing '\n' character, so I'm fixing that too.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add ACPI device ID matching for TI ADC081C/ADC101C/ADC121C ADCs.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The trigger name is documented as unique but drivers are currently
allowed to register triggers with duplicate names. This should be
considered a bug since it makes the 'current_trigger' interface
unusable.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently the ad7266 driver treats any failure to get vref as though the
regulator were not present but this means that if probe deferral is
triggered the driver will act as though the regulator were not present.
Instead only use the internal reference if we explicitly got -ENODEV which
is what is returned for absent regulators.
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ad7266 driver attempts to support deciding between the use of internal
and external power supplies by checking to see if an error is returned when
requesting the regulator. This doesn't work with the current code since the
driver uses a normal regulator_get() which is for non-optional supplies
and so assumes that if a regulator is not provided by the platform then
this is a bug in the platform integration and so substitutes a dummy
regulator. Use regulator_get_optional() instead which indicates to the
framework that the regulator may be absent and provides a dummy regulator
instead.
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
All regulator_get() variants return either a pointer to a regulator or an
ERR_PTR() so testing for NULL makes no sense and may lead to bugs if we
use NULL as a valid regulator. Fix this by using IS_ERR() as expected.
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These two spi_w8r8() calls return a value with is used by the code
following the error check. The dubious use was caused by a cleanup
patch.
Fixes: d34dbee8ac ("staging:iio:accel:kxsd9 cleanup and conversion to iio_chan_spec.")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Alison Schofield