On the Fujitsu-A64FX cores ver(1.0, 1.1), memory access may cause
an undefined fault (Data abort, DFSC=0b111111). This fault occurs under
a specific hardware condition when a load/store instruction performs an
address translation. Any load/store instruction, except non-fault access
including Armv8 and SVE might cause this undefined fault.
The TCR_ELx.NFD1 bit is used by the kernel when CONFIG_RANDOMIZE_BASE
is enabled to mitigate timing attacks against KASLR where the kernel
address space could be probed using the FFR and suppressed fault on
SVE loads.
Since this erratum causes spurious exceptions, which may corrupt
the exception registers, we clear the TCR_ELx.NFDx=1 bits when
booting on an affected CPU.
Signed-off-by: Zhang Lei <zhang.lei@jp.fujitsu.com>
[Generated MIDR value/mask for __cpu_setup(), removed spurious-fault handler
and always disabled the NFDx bits on affected CPUs]
Signed-off-by: James Morse <james.morse@arm.com>
Tested-by: zhang.lei <zhang.lei@jp.fujitsu.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The Allwinner A64 SoC is known[1] to have an unstable architectural
timer, which manifests itself most obviously in the time jumping forward
a multiple of 95 years[2][3]. This coincides with 2^56 cycles at a
timer frequency of 24 MHz, implying that the time went slightly backward
(and this was interpreted by the kernel as it jumping forward and
wrapping around past the epoch).
Investigation revealed instability in the low bits of CNTVCT at the
point a high bit rolls over. This leads to power-of-two cycle forward
and backward jumps. (Testing shows that forward jumps are about twice as
likely as backward jumps.) Since the counter value returns to normal
after an indeterminate read, each "jump" really consists of both a
forward and backward jump from the software perspective.
Unless the kernel is trapping CNTVCT reads, a userspace program is able
to read the register in a loop faster than it changes. A test program
running on all 4 CPU cores that reported jumps larger than 100 ms was
run for 13.6 hours and reported the following:
Count | Event
-------+---------------------------
9940 | jumped backward 699ms
268 | jumped backward 1398ms
1 | jumped backward 2097ms
16020 | jumped forward 175ms
6443 | jumped forward 699ms
2976 | jumped forward 1398ms
9 | jumped forward 356516ms
9 | jumped forward 357215ms
4 | jumped forward 714430ms
1 | jumped forward 3578440ms
This works out to a jump larger than 100 ms about every 5.5 seconds on
each CPU core.
The largest jump (almost an hour!) was the following sequence of reads:
0x0000007fffffffff → 0x00000093feffffff → 0x0000008000000000
Note that the middle bits don't necessarily all read as all zeroes or
all ones during the anomalous behavior; however the low 10 bits checked
by the function in this patch have never been observed with any other
value.
Also note that smaller jumps are much more common, with backward jumps
of 2048 (2^11) cycles observed over 400 times per second on each core.
(Of course, this is partially explained by lower bits rolling over more
frequently.) Any one of these could have caused the 95 year time skip.
Similar anomalies were observed while reading CNTPCT (after patching the
kernel to allow reads from userspace). However, the CNTPCT jumps are
much less frequent, and only small jumps were observed. The same program
as before (except now reading CNTPCT) observed after 72 hours:
Count | Event
-------+---------------------------
17 | jumped backward 699ms
52 | jumped forward 175ms
2831 | jumped forward 699ms
5 | jumped forward 1398ms
Further investigation showed that the instability in CNTPCT/CNTVCT also
affected the respective timer's TVAL register. The following values were
observed immediately after writing CNVT_TVAL to 0x10000000:
CNTVCT | CNTV_TVAL | CNTV_CVAL | CNTV_TVAL Error
--------------------+------------+--------------------+-----------------
0x000000d4a2d8bfff | 0x10003fff | 0x000000d4b2d8bfff | +0x00004000
0x000000d4a2d94000 | 0x0fffffff | 0x000000d4b2d97fff | -0x00004000
0x000000d4a2d97fff | 0x10003fff | 0x000000d4b2d97fff | +0x00004000
0x000000d4a2d9c000 | 0x0fffffff | 0x000000d4b2d9ffff | -0x00004000
The pattern of errors in CNTV_TVAL seemed to depend on exactly which
value was written to it. For example, after writing 0x10101010:
CNTVCT | CNTV_TVAL | CNTV_CVAL | CNTV_TVAL Error
--------------------+------------+--------------------+-----------------
0x000001ac3effffff | 0x1110100f | 0x000001ac4f10100f | +0x1000000
0x000001ac40000000 | 0x1010100f | 0x000001ac5110100f | -0x1000000
0x000001ac58ffffff | 0x1110100f | 0x000001ac6910100f | +0x1000000
0x000001ac66000000 | 0x1010100f | 0x000001ac7710100f | -0x1000000
0x000001ac6affffff | 0x1110100f | 0x000001ac7b10100f | +0x1000000
0x000001ac6e000000 | 0x1010100f | 0x000001ac7f10100f | -0x1000000
I was also twice able to reproduce the issue covered by Allwinner's
workaround[4], that writing to TVAL sometimes fails, and both CVAL and
TVAL are left with entirely bogus values. One was the following values:
CNTVCT | CNTV_TVAL | CNTV_CVAL
--------------------+------------+--------------------------------------
0x000000d4a2d6014c | 0x8fbd5721 | 0x000000d132935fff (615s in the past)
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
========================================================================
Because the CPU can read the CNTPCT/CNTVCT registers faster than they
change, performing two reads of the register and comparing the high bits
(like other workarounds) is not a workable solution. And because the
timer can jump both forward and backward, no pair of reads can
distinguish a good value from a bad one. The only way to guarantee a
good value from consecutive reads would be to read _three_ times, and
take the middle value only if the three values are 1) each unique and
2) increasing. This takes at minimum 3 counter cycles (125 ns), or more
if an anomaly is detected.
However, since there is a distinct pattern to the bad values, we can
optimize the common case (1022/1024 of the time) to a single read by
simply ignoring values that match the error pattern. This still takes no
more than 3 cycles in the worst case, and requires much less code. As an
additional safety check, we still limit the loop iteration to the number
of max-frequency (1.2 GHz) CPU cycles in three 24 MHz counter periods.
For the TVAL registers, the simple solution is to not use them. Instead,
read or write the CVAL and calculate the TVAL value in software.
Although the manufacturer is aware of at least part of the erratum[4],
there is no official name for it. For now, use the kernel-internal name
"UNKNOWN1".
[1]: https://github.com/armbian/build/commit/a08cd6fe7ae9
[2]: https://forum.armbian.com/topic/3458-a64-datetime-clock-issue/
[3]: https://irclog.whitequark.org/linux-sunxi/2018-01-26
[4]: https://github.com/Allwinner-Homlet/H6-BSP4.9-linux/blob/master/drivers/clocksource/arm_arch_timer.c#L272
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The values non secure EL1 needs to use for PMR and RPR registers depends on
the value of SCR_EL3.FIQ.
The values non secure EL1 sees from the distributor and redistributor
depend on whether security is enabled for the GIC or not.
To avoid having to deal with two sets of values for PMR
masking/unmasking, only enable pseudo-NMIs when GIC has non-secure view
of priorities.
Also, add firmware requirements related to SCR_EL3.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add two new ptrace regsets, which can be used to request and change the
pointer authentication keys of a thread. NT_ARM_PACA_KEYS gives access
to the instruction/data address keys, and NT_ARM_PACG_KEYS to the
generic authentication key. The keys are also part of the core dump file
of the process.
The regsets are only exposed if the kernel is compiled with
CONFIG_CHECKPOINT_RESTORE=y, as the only intended use case is
checkpointing and restoring processes that are using pointer
authentication. (This can be changed later if there are other use
cases.)
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In the end, we ended up with quite a lot more than I expected:
- Support for ARMv8.3 Pointer Authentication in userspace (CRIU and
kernel-side support to come later)
- Support for per-thread stack canaries, pending an update to GCC that
is currently undergoing review
- Support for kexec_file_load(), which permits secure boot of a kexec
payload but also happens to improve the performance of kexec
dramatically because we can avoid the sucky purgatory code from
userspace. Kdump will come later (requires updates to libfdt).
- Optimisation of our dynamic CPU feature framework, so that all
detected features are enabled via a single stop_machine() invocation
- KPTI whitelisting of Cortex-A CPUs unaffected by Meltdown, so that
they can benefit from global TLB entries when KASLR is not in use
- 52-bit virtual addressing for userspace (kernel remains 48-bit)
- Patch in LSE atomics for per-cpu atomic operations
- Custom preempt.h implementation to avoid unconditional calls to
preempt_schedule() from preempt_enable()
- Support for the new 'SB' Speculation Barrier instruction
- Vectorised implementation of XOR checksumming and CRC32 optimisations
- Workaround for Cortex-A76 erratum #1165522
- Improved compatibility with Clang/LLD
- Support for TX2 system PMUS for profiling the L3 cache and DMC
- Reflect read-only permissions in the linear map by default
- Ensure MMIO reads are ordered with subsequent calls to Xdelay()
- Initial support for memory hotplug
- Tweak the threshold when we invalidate the TLB by-ASID, so that
mremap() performance is improved for ranges spanning multiple PMDs.
- Minor refactoring and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJcE4TmAAoJELescNyEwWM0Nr0H/iaU7/wQSzHyNXtZoImyKTul
Blu2ga4/EqUrTU7AVVfmkl/3NBILWlgQVpY6tH6EfXQuvnxqD7CizbHyLdyO+z0S
B5PsFUH2GLMNAi48AUNqGqkgb2knFbg+T+9IimijDBkKg1G/KhQnRg6bXX32mLJv
Une8oshUPBVJMsHN1AcQknzKariuoE3u0SgJ+eOZ9yA2ZwKxP4yy1SkDt3xQrtI0
lojeRjxcyjTP1oGRNZC+BWUtGOT35p7y6cGTnBd/4TlqBGz5wVAJUcdoxnZ6JYVR
O8+ob9zU+4I0+SKt80s7pTLqQiL9rxkKZ5joWK1pr1g9e0s5N5yoETXKFHgJYP8=
=sYdt
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 festive updates from Will Deacon:
"In the end, we ended up with quite a lot more than I expected:
- Support for ARMv8.3 Pointer Authentication in userspace (CRIU and
kernel-side support to come later)
- Support for per-thread stack canaries, pending an update to GCC
that is currently undergoing review
- Support for kexec_file_load(), which permits secure boot of a kexec
payload but also happens to improve the performance of kexec
dramatically because we can avoid the sucky purgatory code from
userspace. Kdump will come later (requires updates to libfdt).
- Optimisation of our dynamic CPU feature framework, so that all
detected features are enabled via a single stop_machine()
invocation
- KPTI whitelisting of Cortex-A CPUs unaffected by Meltdown, so that
they can benefit from global TLB entries when KASLR is not in use
- 52-bit virtual addressing for userspace (kernel remains 48-bit)
- Patch in LSE atomics for per-cpu atomic operations
- Custom preempt.h implementation to avoid unconditional calls to
preempt_schedule() from preempt_enable()
- Support for the new 'SB' Speculation Barrier instruction
- Vectorised implementation of XOR checksumming and CRC32
optimisations
- Workaround for Cortex-A76 erratum #1165522
- Improved compatibility with Clang/LLD
- Support for TX2 system PMUS for profiling the L3 cache and DMC
- Reflect read-only permissions in the linear map by default
- Ensure MMIO reads are ordered with subsequent calls to Xdelay()
- Initial support for memory hotplug
- Tweak the threshold when we invalidate the TLB by-ASID, so that
mremap() performance is improved for ranges spanning multiple PMDs.
- Minor refactoring and cleanups"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (125 commits)
arm64: kaslr: print PHYS_OFFSET in dump_kernel_offset()
arm64: sysreg: Use _BITUL() when defining register bits
arm64: cpufeature: Rework ptr auth hwcaps using multi_entry_cap_matches
arm64: cpufeature: Reduce number of pointer auth CPU caps from 6 to 4
arm64: docs: document pointer authentication
arm64: ptr auth: Move per-thread keys from thread_info to thread_struct
arm64: enable pointer authentication
arm64: add prctl control for resetting ptrauth keys
arm64: perf: strip PAC when unwinding userspace
arm64: expose user PAC bit positions via ptrace
arm64: add basic pointer authentication support
arm64/cpufeature: detect pointer authentication
arm64: Don't trap host pointer auth use to EL2
arm64/kvm: hide ptrauth from guests
arm64/kvm: consistently handle host HCR_EL2 flags
arm64: add pointer authentication register bits
arm64: add comments about EC exception levels
arm64: perf: Treat EXCLUDE_EL* bit definitions as unsigned
arm64: kpti: Whitelist Cortex-A CPUs that don't implement the CSV3 field
arm64: enable per-task stack canaries
...
Now that we've added code to support pointer authentication, add some
documentation so that people can figure out if/how to use it.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Reviewed-by: Ramana Radhakrishnan <ramana.radhakrishnan@arm.com>
Cc: Andrew Jones <drjones@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ramana Radhakrishnan <ramana.radhakrishnan@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the infrastructure to handle erratum 1165522 is in place,
let's make it a selectable option and add the required documentation.
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On the affected Cortex-A76 cores (r0p0 to r3p0), if a virtual address
for a cacheable mapping of a location is being accessed by a core while
another core is remapping the virtual address to a new physical page
using the recommended break-before-make sequence, then under very rare
circumstances TLBI+DSB completes before a read using the translation
being invalidated has been observed by other observers. The workaround
repeats the TLBI+DSB operation and is shared with the Qualcomm Falkor
erratum 1009
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Arm v8 architecture supports multiple page sizes - 4k, 16k and
64k. Based on the active page size, the Linux port supports
corresponding hugepage sizes at PMD and PUD(4k only) levels.
In addition, the architecture also supports caching larger sized
ranges (composed of multiple entries) at the PTE and PMD level in the
TLBs using the contiguous bit. The Linux port makes use of this
architectural support to enable additional hugepage sizes.
Describe the two different types of hugepages supported by the arm64
kernel and the hugepage sizes enabled by each.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Document that we actually work around ARM erratum 1188873
Fixes: 95b861a4a6 ("arm64: arch_timer: Add workaround for ARM erratum 1188873")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We advertise the MRS/MSR instructions for toggling SSBS at EL0 using an
HWCAP, so document it along with the others.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fix some typos in our hwcap documentation, where we refer to the wrong
ID register for some of the capabilities.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Giacomo Travaglini <giacomo.travaglini@arm.com>
[will: fix amusing binary constants]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Fix mismatch between SVE registers (Z) and FPSIMD register (V)
- Don't prefix the path for [3] with Linux to stay consistent with
[1] and [2].
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- VHE optimizations
- EL2 address space randomization
- speculative execution mitigations ("variant 3a", aka execution past invalid
privilege register access)
- bugfixes and cleanups
PPC:
- improvements for the radix page fault handler for HV KVM on POWER9
s390:
- more kvm stat counters
- virtio gpu plumbing
- documentation
- facilities improvements
x86:
- support for VMware magic I/O port and pseudo-PMCs
- AMD pause loop exiting
- support for AMD core performance extensions
- support for synchronous register access
- expose nVMX capabilities to userspace
- support for Hyper-V signaling via eventfd
- use Enlightened VMCS when running on Hyper-V
- allow userspace to disable MWAIT/HLT/PAUSE vmexits
- usual roundup of optimizations and nested virtualization bugfixes
Generic:
- API selftest infrastructure (though the only tests are for x86 as of now)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJay19UAAoJEL/70l94x66DGKYIAIu9PTHAEwaX0et15fPW5y2x
rrtS355lSAmMrPJ1nePRQ+rProD/1B0Kizj3/9O+B9OTKKRsorRYNa4CSu9neO2k
N3rdE46M1wHAPwuJPcYvh3iBVXtgbMayk1EK5aVoSXaMXEHh+PWZextkl+F+G853
kC27yDy30jj9pStwnEFSBszO9ua/URdKNKBATNx8WUP6d9U/dlfm5xv3Dc3WtKt2
UMGmog2wh0i7ecXo7hRkMK4R7OYP3ZxAexq5aa9BOPuFp+ZdzC/MVpN+jsjq2J/M
Zq6RNyA2HFyQeP0E9QgFsYS2BNOPeLZnT5Jg1z4jyiD32lAZ/iC51zwm4oNKcDM=
=bPlD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- VHE optimizations
- EL2 address space randomization
- speculative execution mitigations ("variant 3a", aka execution past
invalid privilege register access)
- bugfixes and cleanups
PPC:
- improvements for the radix page fault handler for HV KVM on POWER9
s390:
- more kvm stat counters
- virtio gpu plumbing
- documentation
- facilities improvements
x86:
- support for VMware magic I/O port and pseudo-PMCs
- AMD pause loop exiting
- support for AMD core performance extensions
- support for synchronous register access
- expose nVMX capabilities to userspace
- support for Hyper-V signaling via eventfd
- use Enlightened VMCS when running on Hyper-V
- allow userspace to disable MWAIT/HLT/PAUSE vmexits
- usual roundup of optimizations and nested virtualization bugfixes
Generic:
- API selftest infrastructure (though the only tests are for x86 as
of now)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (174 commits)
kvm: x86: fix a prototype warning
kvm: selftests: add sync_regs_test
kvm: selftests: add API testing infrastructure
kvm: x86: fix a compile warning
KVM: X86: Add Force Emulation Prefix for "emulate the next instruction"
KVM: X86: Introduce handle_ud()
KVM: vmx: unify adjacent #ifdefs
x86: kvm: hide the unused 'cpu' variable
KVM: VMX: remove bogus WARN_ON in handle_ept_misconfig
Revert "KVM: X86: Fix SMRAM accessing even if VM is shutdown"
kvm: Add emulation for movups/movupd
KVM: VMX: raise internal error for exception during invalid protected mode state
KVM: nVMX: Optimization: Dont set KVM_REQ_EVENT when VMExit with nested_run_pending
KVM: nVMX: Require immediate-exit when event reinjected to L2 and L1 event pending
KVM: x86: Fix misleading comments on handling pending exceptions
KVM: x86: Rename interrupt.pending to interrupt.injected
KVM: VMX: No need to clear pending NMI/interrupt on inject realmode interrupt
x86/kvm: use Enlightened VMCS when running on Hyper-V
x86/hyper-v: detect nested features
x86/hyper-v: define struct hv_enlightened_vmcs and clean field bits
...
Some variants of the Arm Cortex-55 cores (r0p0, r0p1, r1p0) suffer
from an erratum 1024718, which causes incorrect updates when DBM/AP
bits in a page table entry is modified without a break-before-make
sequence. The work around is to skip enabling the hardware DBM feature
on the affected cores. The hardware Access Flag management features
is not affected. There are some other cores suffering from this
errata, which could be added to the midr_list to trigger the work
around.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: ckadabi@codeaurora.org
Reviewed-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Expose the new features introduced by Arm v8.4 extensions to
Arm v8-A profile.
These include :
1) Data indpendent timing of instructions. (DIT, exposed as HWCAP_DIT)
2) Unaligned atomic instructions and Single-copy atomicity of loads
and stores. (AT, expose as HWCAP_USCAT)
3) LDAPR and STLR instructions with immediate offsets (extension to
LRCPC, exposed as HWCAP_ILRCPC)
4) Flag manipulation instructions (TS, exposed as HWCAP_FLAGM).
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Remove the invisible RES0 field entries from the table, listing
fields in CPU ID feature registers, as :
1) We are only interested in the user visible fields.
2) The field description may not be up-to-date, as the
field could be assigned a new meaning.
3) We already explain the rules of the fields which are not
visible.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We're now ready to map our vectors in weird and wonderful locations.
On enabling ARM64_HARDEN_EL2_VECTORS, a vector slot gets allocated
if this hasn't been already done via ARM64_HARDEN_BRANCH_PREDICTOR
and gets mapped outside of the normal RAM region, next to the
idmap.
That way, being able to obtain VBAR_EL2 doesn't reveal the mapping
of the rest of the hypervisor code.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Update the documentation to reflect the new tricks we play on the
EL2 mappings...
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- Security mitigations:
- variant 2: invalidating the branch predictor with a call to secure firmware
- variant 3: implementing KPTI for arm64
- 52-bit physical address support for arm64 (ARMv8.2)
- arm64 support for RAS (firmware first only) and SDEI (software
delegated exception interface; allows firmware to inject a RAS error
into the OS)
- Perf support for the ARM DynamIQ Shared Unit PMU
- CPUID and HWCAP bits updated for new floating point multiplication
instructions in ARMv8.4
- Removing some virtual memory layout printks during boot
- Fix initial page table creation to cope with larger than 32M kernel
images when 16K pages are enabled
-----BEGIN PGP SIGNATURE-----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=iEjP
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"The main theme of this pull request is security covering variants 2
and 3 for arm64. I expect to send additional patches next week
covering an improved firmware interface (requires firmware changes)
for variant 2 and way for KPTI to be disabled on unaffected CPUs
(Cavium's ThunderX doesn't work properly with KPTI enabled because of
a hardware erratum).
Summary:
- Security mitigations:
- variant 2: invalidate the branch predictor with a call to
secure firmware
- variant 3: implement KPTI for arm64
- 52-bit physical address support for arm64 (ARMv8.2)
- arm64 support for RAS (firmware first only) and SDEI (software
delegated exception interface; allows firmware to inject a RAS
error into the OS)
- perf support for the ARM DynamIQ Shared Unit PMU
- CPUID and HWCAP bits updated for new floating point multiplication
instructions in ARMv8.4
- remove some virtual memory layout printks during boot
- fix initial page table creation to cope with larger than 32M kernel
images when 16K pages are enabled"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (104 commits)
arm64: Fix TTBR + PAN + 52-bit PA logic in cpu_do_switch_mm
arm64: Turn on KPTI only on CPUs that need it
arm64: Branch predictor hardening for Cavium ThunderX2
arm64: Run enable method for errata work arounds on late CPUs
arm64: Move BP hardening to check_and_switch_context
arm64: mm: ignore memory above supported physical address size
arm64: kpti: Fix the interaction between ASID switching and software PAN
KVM: arm64: Emulate RAS error registers and set HCR_EL2's TERR & TEA
KVM: arm64: Handle RAS SErrors from EL2 on guest exit
KVM: arm64: Handle RAS SErrors from EL1 on guest exit
KVM: arm64: Save ESR_EL2 on guest SError
KVM: arm64: Save/Restore guest DISR_EL1
KVM: arm64: Set an impdef ESR for Virtual-SError using VSESR_EL2.
KVM: arm/arm64: mask/unmask daif around VHE guests
arm64: kernel: Prepare for a DISR user
arm64: Unconditionally enable IESB on exception entry/return for firmware-first
arm64: kernel: Survive corrected RAS errors notified by SError
arm64: cpufeature: Detect CPU RAS Extentions
arm64: sysreg: Move to use definitions for all the SCTLR bits
arm64: cpufeature: __this_cpu_has_cap() shouldn't stop early
...
The Kryo CPUs are also affected by the Falkor 1003 errata, so
we need to do the same workaround on Kryo CPUs. The MIDR is
slightly more complicated here, where the PART number is not
always the same when looking at all the bits from 15 to 4. Drop
the lower 8 bits and just look at the top 4 to see if it's '2'
and then consider those as Kryo CPUs. This covers all the
combinations without having to list them all out.
Fixes: 38fd94b027 ("arm64: Work around Falkor erratum 1003")
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARM v8.4 extensions add new neon instructions for performing a
multiplication of each FP16 element of one vector with the corresponding
FP16 element of a second vector, and to add or subtract this without an
intermediate rounding to the corresponding FP32 element in a third vector.
This patch detects this feature and let the userspace know about it via a
HWCAP bit and MRS emulation.
Cc: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The ARM architecture defines the memory locations that are permitted
to be accessed as the result of a speculative instruction fetch from
an exception level for which all stages of translation are disabled.
Specifically, the core is permitted to speculatively fetch from the
4KB region containing the current program counter 4K and next 4K.
When translation is changed from enabled to disabled for the running
exception level (SCTLR_ELn[M] changed from a value of 1 to 0), the
Falkor core may errantly speculatively access memory locations outside
of the 4KB region permitted by the architecture. The errant memory
access may lead to one of the following unexpected behaviors.
1) A System Error Interrupt (SEI) being raised by the Falkor core due
to the errant memory access attempting to access a region of memory
that is protected by a slave-side memory protection unit.
2) Unpredictable device behavior due to a speculative read from device
memory. This behavior may only occur if the instruction cache is
disabled prior to or coincident with translation being changed from
enabled to disabled.
The conditions leading to this erratum will not occur when either of the
following occur:
1) A higher exception level disables translation of a lower exception level
(e.g. EL2 changing SCTLR_EL1[M] from a value of 1 to 0).
2) An exception level disabling its stage-1 translation if its stage-2
translation is enabled (e.g. EL1 changing SCTLR_EL1[M] from a value of 1
to 0 when HCR_EL2[VM] has a value of 1).
To avoid the errant behavior, software must execute an ISB immediately
prior to executing the MSR that will change SCTLR_ELn[M] from 1 to 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Plenty of acronym soup here:
- Initial support for the Scalable Vector Extension (SVE)
- Improved handling for SError interrupts (required to handle RAS events)
- Enable GCC support for 128-bit integer types
- Remove kernel text addresses from backtraces and register dumps
- Use of WFE to implement long delay()s
- ACPI IORT updates from Lorenzo Pieralisi
- Perf PMU driver for the Statistical Profiling Extension (SPE)
- Perf PMU driver for Hisilicon's system PMUs
- Misc cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJaCcLqAAoJELescNyEwWM0JREH/2FbmD/khGzEtP8LW+o9D8iV
TBM02uWQxS1bbO1pV2vb+512YQO+iWfeQwJH9Jv2FZcrMvFv7uGRnYgAnJuXNGrl
W+LL6OhN22A24LSawC437RU3Xe7GqrtONIY/yLeJBPablfcDGzPK1eHRA0pUzcyX
VlyDruSHWX44VGBPV6JRd3x0vxpV8syeKOjbRvopRfn3Nwkbd76V3YSfEgwoTG5W
ET1sOnXLmHHdeifn/l1Am5FX1FYstpcd7usUTJ4Oto8y7e09tw3bGJCD0aMJ3vow
v1pCUWohEw7fHqoPc9rTrc1QEnkdML4vjJvMPUzwyTfPrN+7uEuMIEeJierW+qE=
=0qrg
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"The big highlight is support for the Scalable Vector Extension (SVE)
which required extensive ABI work to ensure we don't break existing
applications by blowing away their signal stack with the rather large
new vector context (<= 2 kbit per vector register). There's further
work to be done optimising things like exception return, but the ABI
is solid now.
Much of the line count comes from some new PMU drivers we have, but
they're pretty self-contained and I suspect we'll have more of them in
future.
Plenty of acronym soup here:
- initial support for the Scalable Vector Extension (SVE)
- improved handling for SError interrupts (required to handle RAS
events)
- enable GCC support for 128-bit integer types
- remove kernel text addresses from backtraces and register dumps
- use of WFE to implement long delay()s
- ACPI IORT updates from Lorenzo Pieralisi
- perf PMU driver for the Statistical Profiling Extension (SPE)
- perf PMU driver for Hisilicon's system PMUs
- misc cleanups and non-critical fixes"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (97 commits)
arm64: Make ARMV8_DEPRECATED depend on SYSCTL
arm64: Implement __lshrti3 library function
arm64: support __int128 on gcc 5+
arm64/sve: Add documentation
arm64/sve: Detect SVE and activate runtime support
arm64/sve: KVM: Hide SVE from CPU features exposed to guests
arm64/sve: KVM: Treat guest SVE use as undefined instruction execution
arm64/sve: KVM: Prevent guests from using SVE
arm64/sve: Add sysctl to set the default vector length for new processes
arm64/sve: Add prctl controls for userspace vector length management
arm64/sve: ptrace and ELF coredump support
arm64/sve: Preserve SVE registers around EFI runtime service calls
arm64/sve: Preserve SVE registers around kernel-mode NEON use
arm64/sve: Probe SVE capabilities and usable vector lengths
arm64: cpufeature: Move sys_caps_initialised declarations
arm64/sve: Backend logic for setting the vector length
arm64/sve: Signal handling support
arm64/sve: Support vector length resetting for new processes
arm64/sve: Core task context handling
arm64/sve: Low-level CPU setup
...
This patch adds basic documentation of the user/kernel interface
provided by the for SVE.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alan Hayward <alan.hayward@arm.com>
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Szabolcs Nagy <szabolcs.nagy@arm.com>
Cc: linux-api@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch enables detection of hardware SVE support via the
cpufeatures framework, and reports its presence to the kernel and
userspace via the new ARM64_SVE cpucap and HWCAP_SVE hwcap
respectively.
Userspace can also detect SVE using ID_AA64PFR0_EL1, using the
cpufeatures MRS emulation.
When running on hardware that supports SVE, this enables runtime
kernel support for SVE, and allows user tasks to execute SVE
instructions and make of the of the SVE-specific user/kernel
interface extensions implemented by this series.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ITSes on the Hip07 (as present in the Huawei D05) are broken when
it comes to addressing the redistributors, and need to be explicitely
told to address the VLPI page instead of the redistributor base address.
So let's add yet another quirk, fixing up the target address
in the command stream.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We don't document our ELF hwcaps, leaving developers to interpret them
according to hearsay, guesswork, or (in exceptional cases) inspection of
the current kernel code.
This is less than optimal, and it would be far better if we had some
definitive description of each of the ELF hwcaps that developers could
refer to.
This patch adds a document describing the (native) arm64 ELF hwcaps.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Martin <Dave.Martin@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[ Updated new hwcap entries in the document ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARMv8-A adds a few optional features for ARMv8.2 and ARMv8.3.
Expose them to the userspace via HWCAPs and mrs emulation.
SHA2-512 - Instruction support for SHA512 Hash algorithm (e.g SHA512H,
SHA512H2, SHA512U0, SHA512SU1)
SHA3 - SHA3 crypto instructions (EOR3, RAX1, XAR, BCAX).
SM3 - Instruction support for Chinese cryptography algorithm SM3
SM4 - Instruction support for Chinese cryptography algorithm SM4
DP - Dot Product instructions (UDOT, SDOT).
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The Documentation/arm64/memory.txt says:
When using KVM, the hypervisor maps kernel pages in EL2, at a fixed
offset from the kernel VA (top 24bits of the kernel VA set to zero):
In fact, kernel addresses are transleted to HYP with kern_hyp_va macro,
which has more options, and none of them assumes clearing of top 24bits
of the kernel VA.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yury Norov <ynorov@caviumnetworks.com>
[will: removed gory details]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARMv8.2-DCPoP feature introduces persistent memory support to the
architecture, by defining a point of persistence in the memory
hierarchy, and a corresponding cache maintenance operation, DC CVAP.
Expose the support via HWCAP and MRS emulation.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This update comes with:
* Support for lockless operation in the ARM io-pgtable code.
This is an important step to solve the scalability problems in
the common dma-iommu code for ARM
* Some Errata workarounds for ARM SMMU implemenations
* Rewrite of the deferred IO/TLB flush code in the AMD IOMMU
driver. The code suffered from very high flush rates, with the
new implementation the flush rate is down to ~1% of what it
was before
* Support for amd_iommu=off when booting with kexec. Problem
here was that the IOMMU driver bailed out early without
disabling the iommu hardware, if it was enabled in the old
kernel
* The Rockchip IOMMU driver is now available on ARM64
* Align the return value of the iommu_ops->device_group
call-backs to not miss error values
* Preempt-disable optimizations in the Intel VT-d and common
IOVA code to help Linux-RT
* Various other small cleanups and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJZZgddAAoJECvwRC2XARrjurgQANO338GIBr2ZkA0oectidDpZ
Y4yu7W9RH6NyhupJG/Xooya7daBWFjbaA1AVJ3ZZNlMERh69AmehVfRUfVMzF2w+
buma58HQgiJWN1zFD8xdeMzYKms9P77whA88C/9QvrK/klB3LipWP2SC0yvvvyxJ
mMCDpgt+D+CGnIDqbRuyLDQoRu3yjAkAvYb6OzL8DPJVP1Y5oLffGwGnHzJbJnOf
eWJwYHM5ai0uF/Qqy6RNNekacObjVaOLihjugGvokH6ipXfOrSSNriXW9pZiWR5m
S91898YTP3KuWWsJM+N93UAjvc6pL9PqL/OvbB9zdYpzu+5PtUpFXHYcOebKyEEO
4j9CaRzubsWFTFjbYItJnR4WgXQRf4NKOGfTfHMHA+dY8aODYnlXNVdQDAA2aFgn
TUBvHq5xb0zZ3nbPwtTDyW06oDMVfBBarLx2yFI1aQSSh+eg/GtIi5KP28gyFZNz
4gWj0q3g/e3y7WEwNbYV7L3TS0d/p8VUYFtUp7PUCddnWoY+4cJzgidub5xIViZD
Ql0nZzga9pXXIE/kE5Pf74WqrG7JJzZsvK2ABy4+XGrMq6RclJf+0pXbSqiXDpXL
quw8t0oXw0ZEeavQ31Za8mjXBvo5ocM5iintl1wrl2BujHEO3oKqbGsIOaRcLnlN
Ukehbl4OEKzZpD3oLPPk
=pmBf
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This update comes with:
- Support for lockless operation in the ARM io-pgtable code.
This is an important step to solve the scalability problems in the
common dma-iommu code for ARM
- Some Errata workarounds for ARM SMMU implemenations
- Rewrite of the deferred IO/TLB flush code in the AMD IOMMU driver.
The code suffered from very high flush rates, with the new
implementation the flush rate is down to ~1% of what it was before
- Support for amd_iommu=off when booting with kexec.
The problem here was that the IOMMU driver bailed out early without
disabling the iommu hardware, if it was enabled in the old kernel
- The Rockchip IOMMU driver is now available on ARM64
- Align the return value of the iommu_ops->device_group call-backs to
not miss error values
- Preempt-disable optimizations in the Intel VT-d and common IOVA
code to help Linux-RT
- Various other small cleanups and fixes"
* tag 'iommu-updates-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (60 commits)
iommu/vt-d: Constify intel_dma_ops
iommu: Warn once when device_group callback returns NULL
iommu/omap: Return ERR_PTR in device_group call-back
iommu: Return ERR_PTR() values from device_group call-backs
iommu/s390: Use iommu_group_get_for_dev() in s390_iommu_add_device()
iommu/vt-d: Don't disable preemption while accessing deferred_flush()
iommu/iova: Don't disable preempt around this_cpu_ptr()
iommu/arm-smmu-v3: Add workaround for Cavium ThunderX2 erratum #126
iommu/arm-smmu-v3: Enable ACPI based HiSilicon CMD_PREFETCH quirk(erratum 161010701)
iommu/arm-smmu-v3: Add workaround for Cavium ThunderX2 erratum #74
ACPI/IORT: Fixup SMMUv3 resource size for Cavium ThunderX2 SMMUv3 model
iommu/arm-smmu-v3, acpi: Add temporary Cavium SMMU-V3 IORT model number definitions
iommu/io-pgtable-arm: Use dma_wmb() instead of wmb() when publishing table
iommu/io-pgtable: depend on !GENERIC_ATOMIC64 when using COMPILE_TEST with LPAE
iommu/arm-smmu-v3: Remove io-pgtable spinlock
iommu/arm-smmu: Remove io-pgtable spinlock
iommu/io-pgtable-arm-v7s: Support lockless operation
iommu/io-pgtable-arm: Support lockless operation
iommu/io-pgtable: Introduce explicit coherency
iommu/io-pgtable-arm-v7s: Refactor split_blk_unmap
...
Cavium ThunderX2 SMMU doesn't support MSI and also doesn't have unique irq
lines for gerror, eventq and cmdq-sync.
New named irq "combined" is set as a errata workaround, which allows to
share the irq line by register single irq handler for all the interrupts.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Geetha sowjanya <gakula@caviumnetworks.com>
[will: reworked irq equality checking and added SPI check]
Signed-off-by: Will Deacon <will.deacon@arm.com>
HiSilicon SMMUv3 on Hip06/Hip07 platforms doesn't support CMD_PREFETCH
command. The dt based support for this quirk is already present in the
driver(hisilicon,broken-prefetch-cmd). This adds ACPI support for the
quirk using the IORT smmu model number.
Signed-off-by: shameer <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: hanjun <guohanjun@huawei.com>
[will: rewrote patch]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cavium ThunderX2 SMMU implementation doesn't support page 1 register space
and PAGE0_REGS_ONLY option is enabled as an errata workaround.
This option when turned on, replaces all page 1 offsets used for
EVTQ_PROD/CONS, PRIQ_PROD/CONS register access with page 0 offsets.
SMMU resource size checks are now based on SMMU option PAGE0_REGS_ONLY,
since resource size can be either 64k/128k.
For this, arm_smmu_device_dt_probe/acpi_probe has been moved before
platform_get_resource call, so that SMMU options are set beforehand.
Signed-off-by: Linu Cherian <linu.cherian@cavium.com>
Signed-off-by: Geetha Sowjanya <geethasowjanya.akula@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some Cavium Thunder CPUs suffer a problem where a KVM guest may
inadvertently cause the host kernel to quit receiving interrupts.
Use the Group-0/1 trapping in order to deal with it.
[maz]: Adapted patch to the Group-0/1 trapping, reworked commit log
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Some kernel features don't currently work if a task puts a non-zero
address tag in its stack pointer, frame pointer, or frame record entries
(FP, LR).
For example, with a tagged stack pointer, the kernel can't deliver
signals to the process, and the task is killed instead. As another
example, with a tagged frame pointer or frame records, perf fails to
generate call graphs or resolve symbols.
For now, just document these limitations, instead of finding and fixing
everything that doesn't work, as it's not known if anyone needs to use
tags in these places anyway.
In addition, as requested by Dave Martin, generalize the limitations
into a general kernel address tag policy, and refactor
tagged-pointers.txt to include it.
Fixes: d50240a5f6 ("arm64: mm: permit use of tagged pointers at EL0")
Cc: <stable@vger.kernel.org> # 3.12.x-
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Allow checking of a CPU-local erratum
- Add CNTVCT_EL0 trap handler
- Define Cortex-A73 MIDR
- Allow an erratum to be match for all revisions of a core
- Add capability to advertise Cortex-A73 erratum 858921
-----BEGIN PGP SIGNATURE-----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=XSx4
-----END PGP SIGNATURE-----
Merge tag 'arch-timer-errata-prereq' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into for-next/core
Pre-requisites for the arch timer errata workarounds:
- Allow checking of a CPU-local erratum
- Add CNTVCT_EL0 trap handler
- Define Cortex-A73 MIDR
- Allow an erratum to be match for all revisions of a core
- Add capability to advertise Cortex-A73 erratum 858921
* tag 'arch-timer-errata-prereq' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms:
arm64: cpu_errata: Add capability to advertise Cortex-A73 erratum 858921
arm64: cpu_errata: Allow an erratum to be match for all revisions of a core
arm64: Define Cortex-A73 MIDR
arm64: Add CNTVCT_EL0 trap handler
arm64: Allow checking of a CPU-local erratum
In order to work around Cortex-A73 erratum 858921 in a subsequent
patch, add the required capability that advertise the erratum.
As the configuration option it depends on is not present yet,
this has no immediate effect.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
ARMv8.3 adds new instructions to support Release Consistent
processor consistent (RCpc) model, which is weaker than the
RCsc model.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARM v8.3 adds support for new instructions to aid floating-point
multiplication and addition of complex numbers. Expose the support
via HWCAP and MRS emulation
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARMv8.3 adds support for a new instruction to perform conversion
from double precision floating point to integer to match the
architected behaviour of the equivalent Javascript conversion.
Expose the availability via HWCAP and MRS emulation.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On Qualcomm Datacenter Technologies QDF2400 SoCs, the ITS hardware
implementation uses 16Bytes for Interrupt Translation Entry (ITE),
but reports an incorrect value of 8Bytes in GITS_TYPER.ITTE_size.
It might cause kernel memory corruption depending on the number
of MSI(x) that are configured and the amount of memory that has
been allocated for ITEs in its_create_device().
This patch fixes the potential memory corruption by setting the
correct ITE size to 16Bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Qualcomm Datacenter Technologies Falkor v1 CPU may allocate TLB entries
using an incorrect ASID when TTBRx_EL1 is being updated. When the erratum
is triggered, page table entries using the new translation table base
address (BADDR) will be allocated into the TLB using the old ASID. All
circumstances leading to the incorrect ASID being cached in the TLB arise
when software writes TTBRx_EL1[ASID] and TTBRx_EL1[BADDR], a memory
operation is in the process of performing a translation using the specific
TTBRx_EL1 being written, and the memory operation uses a translation table
descriptor designated as non-global. EL2 and EL3 code changing the EL1&0
ASID is not subject to this erratum because hardware is prohibited from
performing translations from an out-of-context translation regime.
Consider the following pseudo code.
write new BADDR and ASID values to TTBRx_EL1
Replacing the above sequence with the one below will ensure that no TLB
entries with an incorrect ASID are used by software.
write reserved value to TTBRx_EL1[ASID]
ISB
write new value to TTBRx_EL1[BADDR]
ISB
write new value to TTBRx_EL1[ASID]
ISB
When the above sequence is used, page table entries using the new BADDR
value may still be incorrectly allocated into the TLB using the reserved
ASID. Yet this will not reduce functionality, since TLB entries incorrectly
tagged with the reserved ASID will never be hit by a later instruction.
Based on work by Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that we have a workaround for Hisilicon erratum 161010101, notes
this in the arm64 silicon-errata document.
The new config option is too long to fit in the existing kconfig column,
so this is widened to accomodate it. At the same time, an existing
whitespace error is corrected, and the existing pattern of a line space
between vendors is enforced for recent additions.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, reword commit message, rework table]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
During a TLB invalidate sequence targeting the inner shareable domain,
Falkor may prematurely complete the DSB before all loads and stores using
the old translation are observed. Instruction fetches are not subject to
the conditions of this erratum. If the original code sequence includes
multiple TLB invalidate instructions followed by a single DSB, onle one of
the TLB instructions needs to be repeated to work around this erratum.
While the erratum only applies to cases in which the TLBI specifies the
inner-shareable domain (*IS form of TLBI) and the DSB is ISH form or
stronger (OSH, SYS), this changes applies the workaround overabundantly--
to local TLBI, DSB NSH sequences as well--for simplicity.
Based on work by Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Documentation for the infrastructure to expose CPU feature
register by emulating MRS.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- Support for execute-only page permissions
- Support for hibernate and DEBUG_PAGEALLOC
- Support for heterogeneous systems with mismatches cache line sizes
- Errata workarounds (A53 843419 update and QorIQ A-008585 timer bug)
- arm64 PMU perf updates, including cpumasks for heterogeneous systems
- Set UTS_MACHINE for building rpm packages
- Yet another head.S tidy-up
- Some cleanups and refactoring, particularly in the NUMA code
- Lots of random, non-critical fixes across the board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJX7k31AAoJELescNyEwWM0XX0H/iOaWCfKlWOhvBsStGUCsLrK
XryTzQT2KjdnLKf3jwP+1ateCuBR5ROurYxoDCX5/7mD63c5KiI338Vbv61a1lE1
AAwjt1stmQVUg/j+kqnuQwB/0DYg+2C8se3D3q5Iyn7zc19cDZJEGcBHNrvLMufc
XgHrgHgl/rzBDDlHJXleknDFge/MfhU5/Q1vJMRRb4JYrpAtmIokzCO75CYMRcCT
ND2QbmppKtsyuFPGUTVbAFzJlP6dGKb3eruYta7/ct5d0pJQxav3u98D2yWGfjdM
YaYq1EmX5Pol7rWumqLtk0+mA9yCFcKLLc+PrJu20Vx0UkvOq8G8Xt70sHNvZU8=
=gdPM
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"It's a bit all over the place this time with no "killer feature" to
speak of. Support for mismatched cache line sizes should help people
seeing whacky JIT failures on some SoCs, and the big.LITTLE perf
updates have been a long time coming, but a lot of the changes here
are cleanups.
We stray outside arch/arm64 in a few areas: the arch/arm/ arch_timer
workaround is acked by Russell, the DT/OF bits are acked by Rob, the
arch_timer clocksource changes acked by Marc, CPU hotplug by tglx and
jump_label by Peter (all CC'd).
Summary:
- Support for execute-only page permissions
- Support for hibernate and DEBUG_PAGEALLOC
- Support for heterogeneous systems with mismatches cache line sizes
- Errata workarounds (A53 843419 update and QorIQ A-008585 timer bug)
- arm64 PMU perf updates, including cpumasks for heterogeneous systems
- Set UTS_MACHINE for building rpm packages
- Yet another head.S tidy-up
- Some cleanups and refactoring, particularly in the NUMA code
- Lots of random, non-critical fixes across the board"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (100 commits)
arm64: tlbflush.h: add __tlbi() macro
arm64: Kconfig: remove SMP dependence for NUMA
arm64: Kconfig: select OF/ACPI_NUMA under NUMA config
arm64: fix dump_backtrace/unwind_frame with NULL tsk
arm/arm64: arch_timer: Use archdata to indicate vdso suitability
arm64: arch_timer: Work around QorIQ Erratum A-008585
arm64: arch_timer: Add device tree binding for A-008585 erratum
arm64: Correctly bounds check virt_addr_valid
arm64: migrate exception table users off module.h and onto extable.h
arm64: pmu: Hoist pmu platform device name
arm64: pmu: Probe default hw/cache counters
arm64: pmu: add fallback probe table
MAINTAINERS: Update ARM PMU PROFILING AND DEBUGGING entry
arm64: Improve kprobes test for atomic sequence
arm64/kvm: use alternative auto-nop
arm64: use alternative auto-nop
arm64: alternative: add auto-nop infrastructure
arm64: lse: convert lse alternatives NOP padding to use __nops
arm64: barriers: introduce nops and __nops macros for NOP sequences
arm64: sysreg: replace open-coded mrs_s/msr_s with {read,write}_sysreg_s
...
Erratum A-008585 says that the ARM generic timer counter "has the
potential to contain an erroneous value for a small number of core
clock cycles every time the timer value changes". Accesses to TVAL
(both read and write) are also affected due to the implicit counter
read. Accesses to CVAL are not affected.
The workaround is to reread TVAL and count registers until successive
reads return the same value. Writes to TVAL are replaced with an
equivalent write to CVAL.
The workaround is to reread TVAL and count registers until successive reads
return the same value, and when writing TVAL to retry until counter
reads before and after the write return the same value.
The workaround is enabled if the fsl,erratum-a008585 property is found in
the timer node in the device tree. This can be overridden with the
clocksource.arm_arch_timer.fsl-a008585 boot parameter, which allows KVM
users to enable the workaround until a mechanism is implemented to
automatically communicate this information.
This erratum can be found on LS1043A and LS2080A.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Scott Wood <oss@buserror.net>
[will: renamed read macro to reflect that it's not usually unstable]
Signed-off-by: Will Deacon <will.deacon@arm.com>
We already have a workaround for Cortex-A57 erratum #852523,
but Cortex-A72 r0p0 to r0p2 do suffer from the same issue
(known as erratum #853709).
Let's document the fact that we already handle this.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The ACPI 6.1 specification was recently released at the end of January
2016, but the arm64 kernel documentation for the use of ACPI was written
for the 5.1 version of the spec. There were significant additions to the
spec that had not yet been mentioned -- for example, the 6.0 mechanisms
added to make it easier to define processors and low power idle states,
as well as the 6.1 addition allowing regular interrupts (not just from
GPIO) be used to signal ACPI general purpose events.
This patch reflects going back through and examining the specs in detail
and updating content appropriately. Whilst there, a few odds and ends of
typos were caught as well. This brings the documentation up to date with
ACPI 6.1 for arm64.
Signed-off-by: Al Stone <al.stone@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Roy Franz <roy.franz@hpe.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The erratum fixes the hang of ITS SYNC command by avoiding inter node
io and collections/cpu mapping on thunderx dual-socket platform.
This fix is only applicable for Cavium's ThunderX dual-socket platform.
Reviewed-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Ganapatrao Kulkarni <gkulkarni@caviumnetworks.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The updates include:
* Rate limiting for the VT-d fault handler
* Remove statistics code from the AMD IOMMU driver. It is unused
and should be replaced by something more generic if needed
* Per-domain pagesize-bitmaps in IOMMU core code to support
systems with different types of IOMMUs
* Support for ACPI devices in the AMD IOMMU driver
* 4GB mode support for Mediatek IOMMU driver
* ARM-SMMU updates from Will Deacon:
- Support for 64k pages with SMMUv1 implementations
(e.g MMU-401)
- Remove open-coded 64-bit MMIO accessors
- Initial support for 16-bit VMIDs, as supported by some
ThunderX SMMU implementations
- A couple of errata workarounds for silicon in the
field
* Various fixes here and there
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jpPD
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"The updates include:
- rate limiting for the VT-d fault handler
- remove statistics code from the AMD IOMMU driver. It is unused and
should be replaced by something more generic if needed
- per-domain pagesize-bitmaps in IOMMU core code to support systems
with different types of IOMMUs
- support for ACPI devices in the AMD IOMMU driver
- 4GB mode support for Mediatek IOMMU driver
- ARM-SMMU updates from Will Deacon:
- support for 64k pages with SMMUv1 implementations (e.g MMU-401)
- remove open-coded 64-bit MMIO accessors
- initial support for 16-bit VMIDs, as supported by some ThunderX
SMMU implementations
- a couple of errata workarounds for silicon in the field
- various fixes here and there"
* tag 'iommu-updates-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (44 commits)
iommu/arm-smmu: Use per-domain page sizes.
iommu/amd: Remove statistics code
iommu/dma: Finish optimising higher-order allocations
iommu: Allow selecting page sizes per domain
iommu: of: enforce const-ness of struct iommu_ops
iommu: remove unused priv field from struct iommu_ops
iommu/dma: Implement scatterlist segment merging
iommu/arm-smmu: Clear cache lock bit of ACR
iommu/arm-smmu: Support SMMUv1 64KB supplement
iommu/arm-smmu: Decouple context format from kernel config
iommu/arm-smmu: Tidy up 64-bit/atomic I/O accesses
io-64-nonatomic: Add relaxed accessor variants
iommu/arm-smmu: Work around MMU-500 prefetch errata
iommu/arm-smmu: Convert ThunderX workaround to new method
iommu/arm-smmu: Differentiate specific implementations
iommu/arm-smmu: Workaround for ThunderX erratum #27704
iommu/arm-smmu: Add support for 16 bit VMID
iommu/amd: Move get_device_id() and friends to beginning of file
iommu/amd: Don't use IS_ERR_VALUE to check integer values
iommu/amd: Signedness bug in acpihid_device_group()
...
MMU-500 erratum #841119 is tickled by a particular set of circumstances
interacting with the next-page prefetcher. Since said prefetcher is
quite dumb and actually detrimental to performance in some cases (by
causing unwanted TLB evictions for non-sequential access patterns), we
lose very little by turning it off, and what we gain is a guarantee that
the erratum is never hit.
As a bonus, the same workaround will also prevent erratum #826419 once
v7 short descriptor support is implemented.
CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Due to erratum #27704, the CN88xx SMMUv2 implementation supports only
shared ASID and VMID numberspaces.
This patch ensures that ASID and VMIDs are unique across all SMMU
instances on affected Cavium systems.
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Signed-off-by: Akula Geethasowjanya <Geethasowjanya.Akula@caviumnetworks.com>
[will: commit message, comments and formatting]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Instead of going out of our way to relocate the initrd if it turns out
to occupy memory that is not covered by the linear mapping, just add the
initrd to the linear mapping. This puts the burden on the bootloader to
pass initrd= and mem= options that are mutually consistent.
Note that, since the placement of the linear region in the PA space is
also dependent on the placement of the kernel Image, which may reside
anywhere in memory, we may still end up with a situation where the initrd
and the kernel Image are simply too far apart to be covered by the linear
region.
Since we now leave it up to the bootloader to pass the initrd in memory
that is guaranteed to be accessible by the kernel, add a mention of this to
the arm64 boot protocol specification as well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On ThunderX T88 pass 1.x through 2.1 parts, broadcast TLBI
instructions may cause the icache to become corrupted if it contains
data for a non-current ASID.
This patch implements the workaround (which invalidates the local
icache when switching the mm) by using code patching.
Signed-off-by: Andrew Pinski <apinski@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This relaxes the kernel Image placement requirements, so that it
may be placed at any 2 MB aligned offset in physical memory.
This is accomplished by ignoring PHYS_OFFSET when installing
memblocks, and accounting for the apparent virtual offset of
the kernel Image. As a result, virtual address references
below PAGE_OFFSET are correctly mapped onto physical references
into the kernel Image regardless of where it sits in memory.
Special care needs to be taken for dealing with memory limits passed
via mem=, since the generic implementation clips memory top down, which
may clip the kernel image itself if it is loaded high up in memory. To
deal with this case, we simply add back the memory covering the kernel
image, which may result in more memory to be retained than was passed
as a mem= parameter.
Since mem= should not be considered a production feature, a panic notifier
handler is installed that dumps the memory limit at panic time if one was
set.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
It's not immediately obvious which hardware errata are worked around in
the Linux kernel for an arbitrary kernel tree, so add a file to keep
track of what we're working around.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3six
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (91 commits)
arm64/efi: fix libstub build under CONFIG_MODVERSIONS
ARM64: Enable multi-core scheduler support by default
arm64/efi: move arm64 specific stub C code to libstub
arm64: page-align sections for DEBUG_RODATA
arm64: Fix build with CONFIG_ZONE_DMA=n
arm64: Fix compat register mappings
arm64: Increase the max granular size
arm64: remove bogus TASK_SIZE_64 check
arm64: make Timer Interrupt Frequency selectable
arm64/mm: use PAGE_ALIGNED instead of IS_ALIGNED
arm64: cachetype: fix definitions of ICACHEF_* flags
arm64: cpufeature: declare enable_cpu_capabilities as static
genirq: Make the cpuhotplug migration code less noisy
arm64: Constify hwcap name string arrays
arm64/kvm: Make use of the system wide safe values
arm64/debug: Make use of the system wide safe value
arm64: Move FP/ASIMD hwcap handling to common code
arm64/HWCAP: Use system wide safe values
arm64/capabilities: Make use of system wide safe value
arm64: Delay cpu feature capability checks
...
This patch adds the page size to the arm64 kernel image header
so that one can infer the PAGESIZE used by the kernel. This will
be helpful to diagnose failures to boot the kernel with page size
not supported by the CPU.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The current requirements do not describe the case where a GICv3
system gets booted with system register access disabled, and
expect the kernel to drive GICv3 in GICv2 mode.
Describe the expected settings for that particular case.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Clarify that the memory below the start of the image but inside the
region covered by the linear mapping has no special significance to
the kernel, and may be used by the firmware provided that it is marked
as reserved.
Also, fix up some whitespace errors.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, the FDT blob needs to be in the same 512 MB region as
the kernel, so that it can be mapped into the kernel virtual memory
space very early on using a minimal set of statically allocated
translation tables.
Now that we have early fixmap support, we can relax this restriction,
by moving the permanent FDT mapping to the fixmap region instead.
This way, the FDT blob may be anywhere in memory.
This also moves the vetting of the FDT to mmu.c, since the early
init code in head.S does not handle mapping of the FDT anymore.
At the same time, fix up some comments in head.S that have gone stale.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
One more documentation file are also being added:
A section by section review of the ACPI spec (acpi_object_usage.txt)
to note recommendations and prohibitions on the use of the numerous
ACPI tables and objects. This sets out the current expectations of
the firmware by Linux very explicitly (or as explicitly as I can, for
now).
CC: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
CC: Yi Li <phoenix.liyi@huawei.com>
CC: Mark Langsdorf <mlangsdo@redhat.com>
CC: Ashwin Chaugule <ashwinc@codeaurora.org>
Acked-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add documentation for the guidelines of how to use ACPI
on ARM64.
Reviewed-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Yi Li <phoenix.liyi@huawei.com>
Reviewed-by: Mark Langsdorf <mlangsdo@redhat.com>
Reviewed-by: Ashwin Chaugule <ashwinc@codeaurora.org>
Acked-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Emulate deprecated 'setend' instruction for AArch32 bit tasks.
setend [le/be] - Sets the endianness of EL0
On systems with CPUs which support mixed endian at EL0, the hardware
support for the instruction can be enabled by setting the SCTLR_EL1.SED
bit. Like the other emulated instructions it is controlled by an entry in
/proc/sys/abi/. For more information see :
Documentation/arm64/legacy_instructions.txt
The instruction is emulated by setting/clearing the SPSR_EL1.E bit, which
will be reflected in the PSTATE.E in AArch32 context.
This patch also restores the native endianness for the execution of signal
handlers, since the process could have changed the endianness.
Note: All CPUs on the system must have mixed endian support at EL0. Once the
handler is registered, hotplugging a CPU which doesn't support mixed endian,
could lead to unexpected results/behavior in applications.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The CP15 barrier instructions (CP15ISB, CP15DSB and CP15DMB) are
deprecated in the ARMv7 architecture, superseded by ISB, DSB and DMB
instructions respectively. Some implementations may provide the
ability to disable the CP15 barriers by disabling the CP15BEN bit in
SCTLR_EL1. If not enabled, the encodings for these instructions become
undefined.
To support legacy software using these instructions, this patch
register hooks to -
* emulate CP15 barriers and warn the user about their use
* toggle CP15BEN in SCTLR_EL1
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The SWP instruction was deprecated in the ARMv6 architecture. The
ARMv7 multiprocessing extensions mandate that SWP/SWPB instructions
are treated as undefined from reset, with the ability to enable them
through the System Control Register SW bit. With ARMv8, the option to
enable these instructions through System Control Register was dropped
as well.
To support legacy applications using these instructions, port the
emulation of the SWP and SWPB instructions from the arm port to arm64.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Typically, providing support for legacy instructions requires
emulating the behaviour of instructions whose encodings have become
undefined. If the instructions haven't been removed from the
architecture, there maybe an option in the implementation to turn
on/off the support for these instructions.
Create common infrastructure to support legacy instruction
emulation. In addition to emulation, also provide an option to support
hardware execution when supported. The default execution mode (one of
undef, emulate, hw exeuction) is dependent on the state of the
instruction (deprecated or obsolete) in the architecture and
can specified at the time of registering the instruction handlers. The
runtime state of the emulation can be controlled by writing to
individual nodes in sysctl. The expected default behaviour is
documented as part of this patch.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There is no swapper_pgd_dir, it meant swapper_pg_dir.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Fixes and code refactoring for stage2 kvm MMU unmap_range
- Support unmapping IPAs on deleting memslots for arm and arm64
- Support MMIO mappings in stage2 faults
- KVM VGIC v2 emulation on GICv3 hardware
- Big-Endian support for arm/arm64 (guest and host)
- Debug Architecture support for arm64 (arm32 is on Christoffer's todo list)
- Detect non page-aligned GICV regions and bail out (plugs guest-can-crash host bug)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT3oZTAAoJEEtpOizt6ddyKQIH/1Bj/cZYSkkSf3IJfQhHRbWN
jS37IBsvcHwjHkRJxCNmQuKP/Ho5XEusluPGrVY25PAgBMl+ouPqAuKzUk+GEab6
snjJjDFqw0zs0x0h3tg6UwfZdF+eyyIkmFGn8/IATD5P3PPd8kWBVtYnSnZmYK+R
KJNVcp6RPDrt9kvUDY8Ln9fW99Jl+7CdgQAnc3QkHcXUlanLyrfq+fE1lSzyrbhZ
ETzyMFAX4kCdc8tflgyyBS4A7+RvfQ6ZIQummxoAMFHIoSk90dtK7ovX68rd9U3e
yL+mpe130+dTIFpUMbxCnIdE7C0eud3vcgXC6MuWtFjUrxQoaEgsVE+ffGC5tX0=
=axkp
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm
KVM/ARM New features for 3.17 include:
- Fixes and code refactoring for stage2 kvm MMU unmap_range
- Support unmapping IPAs on deleting memslots for arm and arm64
- Support MMIO mappings in stage2 faults
- KVM VGIC v2 emulation on GICv3 hardware
- Big-Endian support for arm/arm64 (guest and host)
- Debug Architecture support for arm64 (arm32 is on Christoffer's todo list)
Conflicts:
virt/kvm/arm/vgic.c [last minute cherry-pick from 3.17 to 3.16]
This patch allows support for 3 levels of page tables with 64KB page
configuration allowing 48-bit VA space. The pgd is no longer a full
PAGE_SIZE (PTRS_PER_PGD is 64) and (swapper|idmap)_pg_dir are not fully
populated (pgd_alloc falls back to kzalloc).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Jungseok Lee <jungseoklee85@gmail.com>
Rather than guessing what the maximum vmmemap space should be, this
patch allows the calculation based on the VA_BITS and sizeof(struct
page). The vmalloc space extends to the beginning of the vmemmap space.
Since the virtual kernel memory layout now depends on the build
configuration, this patch removes the detailed description in
Documentation/arm64/memory.txt in favour of information printed during
kernel booting.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Jungseok Lee <jungseoklee85@gmail.com>
This patch adds memory layout and translation lookup information
about 48-bit address space with 4K pages. The description is based
on 4 levels of translation tables.
Signed-off-by: Jungseok Lee <jays.lee@samsung.com>
Reviewed-by: Sungjinn Chung <sungjinn.chung@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Jungseok Lee <jungseoklee85@gmail.com>
Linux has some requirements that must be satisfied in order to boot
on a system built with a GICv3.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently the kernel Image is stripped of everything past the initial
stack, and at runtime the memory is initialised and used by the kernel.
This makes the effective minimum memory footprint of the kernel larger
than the size of the loaded binary, though bootloaders have no mechanism
to identify how large this minimum memory footprint is. This makes it
difficult to choose safe locations to place both the kernel and other
binaries required at boot (DTB, initrd, etc), such that the kernel won't
clobber said binaries or other reserved memory during initialisation.
Additionally when big endian support was added the image load offset was
overlooked, and is currently of an arbitrary endianness, which makes it
difficult for bootloaders to make use of it. It seems that bootloaders
aren't respecting the image load offset at present anyway, and are
assuming that offset 0x80000 will always be correct.
This patch adds an effective image size to the kernel header which
describes the amount of memory from the start of the kernel Image binary
which the kernel expects to use before detecting memory and handling any
memory reservations. This can be used by bootloaders to choose suitable
locations to load the kernel and/or other binaries such that the kernel
will not clobber any memory unexpectedly. As before, memory reservations
are required to prevent the kernel from clobbering these locations
later.
Both the image load offset and the effective image size are forced to be
little-endian regardless of the native endianness of the kernel to
enable bootloaders to load a kernel of arbitrary endianness. Bootloaders
which wish to make use of the load offset can inspect the effective
image size field for a non-zero value to determine if the offset is of a
known endianness. To enable software to determine the endinanness of the
kernel as may be required for certain use-cases, a new flags field (also
little-endian) is added to the kernel header to export this information.
The documentation is updated to clarify these details. To discourage
future assumptions regarding the value of text_offset, the value at this
point in time is removed from the main flow of the documentation (though
kept as a compatibility note). Some minor formatting issues in the
documentation are also corrected.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Tom Rini <trini@ti.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Kevin Hilman <kevin.hilman@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add explanation of arm64 EFI stub and kernel image header changes
needed to masquerade as a PE/COFF application.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
- Additional cache flushing during boot (needed in the presence of
external caches or under virtualisation)
- DMA range invalidation fix for non cache line aligned buffers
- Build failure fix with !COMPAT
- Kconfig update for STRICT_DEVMEM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=mDkd
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull second set of arm64 updates from Catalin Marinas:
"A second pull request for this merging window, mainly with fixes and
docs clarification:
- Documentation clarification on CPU topology and booting
requirements
- Additional cache flushing during boot (needed in the presence of
external caches or under virtualisation)
- DMA range invalidation fix for non cache line aligned buffers
- Build failure fix with !COMPAT
- Kconfig update for STRICT_DEVMEM"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix DMA range invalidation for cache line unaligned buffers
arm64: Add missing Kconfig for CONFIG_STRICT_DEVMEM
arm64: fix !CONFIG_COMPAT build failures
Revert "arm64: virt: ensure visibility of __boot_cpu_mode"
arm64: Relax the kernel cache requirements for boot
arm64: Update the TCR_EL1 translation granule definitions for 16K pages
ARM: topology: Make it clear that all CPUs need to be described
Add support for early IO or memory mappings which are needed before the
normal ioremap() is usable. This also adds fixmap support for permanent
fixed mappings such as that used by the earlyprintk device register
region.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With system caches for the host OS or architected caches for guest OS we
cannot easily guarantee that there are no dirty or stale cache lines for
the areas of memory written by the kernel during boot with the MMU off
(therefore non-cacheable accesses).
This patch adds the necessary cache maintenance during boot and relaxes
the booting requirements.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The patch moves the PCI I/O space (currently at 64K) before the
earlyprintk mapping and extends it to 16MB.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch expands the VA_BITS to 42 when the 64K page configuration is
enabled allowing 2TB kernel linear mapping. Linux still uses 2 levels of
page tables in this configuration with pgd now being a full page.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
There are a few points in the arm64 booting document which are unclear
(such as the initial state of secondary CPUs), and/or have not been
documented (PSCI is a supported mechanism for booting secondary CPUs).
This patch amends the arm64 boot document to better express the
(existing) requirements, and to describe PSCI as a supported booting
mechanism.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Fu Wei <tekkamanninja@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit d50240a5f6 ("arm64: mm: permit use of tagged pointers at EL0")
added support for tagged pointers in userspace, but the corresponding
update to Documentation/ contained some imprecise statements.
This patch fixes up some minor ambiguities in the text, hopefully making
it more clear about exactly what the kernel expects from user virtual
addresses.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The current description of DTB placement requirements does not quite
match the kernel code in head.S: __vet_fdt and __create_page_tables.
This patch tweaks the text to match the actual requirements placed on
it by the code.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
TCR.TBI0 can be used to cause hardware address translation to ignore the
top byte of userspace virtual addresses. Whilst not especially useful in
standard C programs, this can be used by JITs to `tag' pointers with
various pieces of metadata.
This patch enables this bit for AArch64 Linux, and adds a new file to
Documentation/arm64/ which describes some potential caveats when using
tagged virtual addresses.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Expand the arm64 image header to allow for co-existance with
PE/COFF header required by the EFI stub. The PE/COFF format
requires the "MZ" header to be at offset 0, and the offset
to the PE/COFF header to be at offset 0x3c. The image
header is expanded to allow 2 instructions at the beginning
to accommodate a benign intruction at offset 0 that includes
the "MZ" header, a magic number, and the offset to the PE/COFF
header.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
HYP mode has access to some of the kernel pages. Document the
memory mapping and the offset between kernel VA and HYP VA.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds support for "earlyprintk=" parameter on the kernel
command line. The format is:
earlyprintk=<name>[,<addr>][,<options>]
where <name> is the name of the (UART) device, e.g. "pl011", <addr> is
the I/O address. The <options> aren't currently used.
The mapping of the earlyprintk device is done very early during kernel
boot and there are restrictions on which functions it can call. A
special early_io_map() function is added which creates the mapping from
the pre-defined EARLY_IOBASE to the device I/O address passed via the
kernel parameter. The pgd entry corresponding to EARLY_IOBASE is
pre-populated in head.S during kernel boot.
Only PL011 is currently supported and it is assumed that the interface
is already initialised by the boot loader before the kernel is started.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fixes a term in Documentation/arm64/memory.txt
The modification is based on Catalin Marinas <catalin.marinas@arm.com>'s
suggestion:
"memory" in "ffffffc000000000 ffffffffffffffff 256GB memory"
should be treated as "kernel logical memory map".
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The virtual memory layout is described in
Documentation/arm64/memory.txt. This patch adds the MMU definitions for
the 4KB and 64KB translation table configurations. The SECTION_SIZE is
2MB with 4KB page and 512MB with 64KB page configuration.
PHYS_OFFSET is calculated at run-time and stored in a variable (no
run-time code patching at this stage).
On the current implementation, both user and kernel address spaces are
512G (39-bit) each with a maximum of 256G for the RAM linear mapping.
Linux uses 3 levels of translation tables with the 4K page configuration
and 2 levels with the 64K configuration. Extending the memory space
beyond 39-bit with the 4K pages or 42-bit with 64K pages requires an
additional level of translation tables.
The SPARSEMEM configuration is global to all AArch64 platforms and
allows for 1GB sections with SPARSEMEM_VMEMMAP enabled by default.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The patch adds the kernel booting and the initial setup code.
Documentation/arm64/booting.txt describes the booting protocol on the
AArch64 Linux kernel. This is subject to change following the work on
boot standardisation, ACPI.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Zhang Lei