We preallocate a few of the message types we get back from the mon. If we
get a larger message than we are expecting, fall back to trying to allocate
a new one instead of blindly using the one we have.
CC: stable@vger.kernel.org
Signed-off-by: Sage Weil <sage@redhat.com>
Reviewed-by: Ilya Dryomov <ilya.dryomov@inktank.com>
When a writeback or a promotion of a block is completed, the cell of
that block is removed from the prison, the block is marked as clean, and
the clear_dirty() callback of the cache policy is called.
Unfortunately, performing those actions in this order allows an incoming
new write bio for that block to come in before clearing the dirty status
is completed and therefore possibly causing one of these two scenarios:
Scenario A:
Thread 1 Thread 2
cell_defer() .
- cell removed from prison .
- detained bios queued .
. incoming write bio
. remapped to cache
. set_dirty() called,
. but block already dirty
. => it does nothing
clear_dirty() .
- block marked clean .
- policy clear_dirty() called .
Result: Block is marked clean even though it is actually dirty. No
writeback will occur.
Scenario B:
Thread 1 Thread 2
cell_defer() .
- cell removed from prison .
- detained bios queued .
clear_dirty() .
- block marked clean .
. incoming write bio
. remapped to cache
. set_dirty() called
. - block marked dirty
. - policy set_dirty() called
- policy clear_dirty() called .
Result: Block is properly marked as dirty, but policy thinks it is clean
and therefore never asks us to writeback it.
This case is visible in "dmsetup status" dirty block count (which
normally decreases to 0 on a quiet device).
Fix these issues by calling clear_dirty() before calling cell_defer().
Incoming bios for that block will then be detained in the cell and
released only after clear_dirty() has completed, so the race will not
occur.
Found by inspecting the code after noticing spurious dirty counts
(scenario B).
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
If we are running in a kdump environment, resources are scarce.
For some SCSI setups with a huge set of shared tags, we run out
of memory allocating what the drivers is asking for. So implement
a scale back logic to reduce the tag depth for those cases, allowing
the driver to successfully load.
We should extend this to detect low memory situations, and implement
a sane fallback for those (1 queue, 64 tags, or something like that).
Tested-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When RANDOMIZE_BASE (KASLR) is enabled; or the sum of all loaded
modules exceeds 512 MiB, then loading modules fails with a warning
(and hence a vmalloc allocation failure) because the PTEs for the
newly-allocated vmalloc address space are not zero.
WARNING: CPU: 0 PID: 494 at linux/mm/vmalloc.c:128
vmap_page_range_noflush+0x2a1/0x360()
This is caused by xen_setup_kernel_pagetables() copying
level2_kernel_pgt into level2_fixmap_pgt, overwriting many non-present
entries.
Without KASLR, the normal kernel image size only covers the first half
of level2_kernel_pgt and module space starts after that.
L4[511]->level3_kernel_pgt[510]->level2_kernel_pgt[ 0..255]->kernel
[256..511]->module
[511]->level2_fixmap_pgt[ 0..505]->module
This allows 512 MiB of of module vmalloc space to be used before
having to use the corrupted level2_fixmap_pgt entries.
With KASLR enabled, the kernel image uses the full PUD range of 1G and
module space starts in the level2_fixmap_pgt. So basically:
L4[511]->level3_kernel_pgt[510]->level2_kernel_pgt[0..511]->kernel
[511]->level2_fixmap_pgt[0..505]->module
And now no module vmalloc space can be used without using the corrupt
level2_fixmap_pgt entries.
Fix this by properly converting the level2_fixmap_pgt entries to MFNs,
and setting level1_fixmap_pgt as read-only.
A number of comments were also using the the wrong L3 offset for
level2_kernel_pgt. These have been corrected.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
I am leaving Samsung, so my current e-mail address is not going to work
any longer. Replace it with my private one. In addition, Sylwester
Nawrocki is being added as co-maintainer for Samsung clock drivers to
take some of the responsibilities, as I will be doing my part in my spare
time.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the IRQCHIP_SKIP_SET_WAKE flag to baytrail gpio irq_chip
to resolve unbalaced IRQ wake disable warnings.
Suggested-by: Borun Fu <borun.fu@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix to return -ENOMEM from the workqueue alloc error handling
case instead of 0, as done elsewhere in this function.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
drivers/block/rbd.c: In function ‘rbd_dev_device_setup’:
drivers/block/rbd.c:5090:19: warning: format not a string literal and no format arguments [-Wformat-security]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Pull cifs/smb3 fixes from Steve French:
"This includes various cifs and smb3 bug fixes including those for bugs
found with the recently updated xfstests.
Also I am working fixes for two additional cifs problems found by
xfstests which I plan to send later (when reviewed and run additional
tests)"
* 'for-next-3.17' of git://git.samba.org/sfrench/cifs-2.6:
Clarify Kconfig help text for CIFS and SMB2/SMB3
CIFS: Fix wrong filename length for SMB2
CIFS: Fix wrong restart readdir for SMB1
CIFS: Fix directory rename error
cifs: No need to send SIGKILL to demux_thread during umount
cifs: Allow directIO read/write during cache=strict
cifs: remove unneeded check of null checking in if condition
cifs: fix a possible use of uninit variable in SMB2_sess_setup
cifs: fix memory leak when password is supplied multiple times
cifs: fix a possible null pointer deref in decode_ascii_ssetup
Trivial whitespace fix
ForcePads are found on HP EliteBook 1040 laptops. They lack any kind of
physical buttons, instead they generate primary button click when user
presses somewhat hard on the surface of the touchpad. Unfortunately they
also report primary button click whenever there are 2 or more contacts
on the pad, messing up all multi-finger gestures (2-finger scrolling,
multi-finger tapping, etc). To cope with this behavior we introduce a
delay (currently 50 msecs) in reporting primary press in case more
contacts appear.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When trying to use the matrix-keypad driver with GPIO drivers that
require nested irq handlers (e.g. I2C GPIO adapters like PCA9554),
request_irq() fails because the GPIO driver requires a threaded
interrupt handler.
Use request_any_context_irq() to be able to use any GPIO driver as
keypad driver.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the case where the CHG/interrupt line mode is not configured correctly,
this warning is output to dmesg output for each interrupt. Downgrade the
message to debug.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Fix Kconfig menu structure
- Fix number of syscalls
- Fix compilation warnings from allmodconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlQO4a0ACgkQykllyylKDCE1NACeIFiXdvY7iy4UZyGMTHcdPnH9
o+kAn0v4x8eSaBRXtqYyxMc74US4Qu2N
=3RdC
-----END PGP SIGNATURE-----
Merge tag 'microblaze-3.17-rc5' of git://git.monstr.eu/linux-2.6-microblaze
Pull arch/microblaze fixes from Michal Simek:
- Kconfig menu structure fix
- fix number of syscalls
- fix compilation warnings from allmodconfig
* tag 'microblaze-3.17-rc5' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix number of syscalls
microblaze: Rename Advance setup to Kernel features
microblaze: Add mm/Kconfig to advance menu
arch/microblaze/include/asm/uaccess.h: Use pr_devel() instead of pr_debug()
arch/microblaze/include/asm/entry.h: Include "linux/linkage.h" to avoid compiling issue
Endpoint 0 should not be disabled, so we start loop counter from number 1.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes kernel panic/interrupt storm/etc issues if bootloader
left s3c-hsotg module in enabled state. Now interrupt handler is enabled
only after proper configuration of hardware registers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This leads to potential spinlock recursion in composite framework, other
udc drivers also don't call it directly from pullup method.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes possible freeze caused by infinite loop in interrupt
context.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Generic PHY Framework a NULL phy is considered to be a valid phy
thus the "if (hsotg->phy)" check does not give us the information whether
the Generic PHY Framework is used.
In addition to the above this patch also removes phy_init from probe and
phy_exit from remove. This is not necessary when init/exit is done in the
s3c_hsotg_phy_enable/disable functions.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver is removed s3c_hsotg_phy_disable is called three times
instead of once. This results in decreasing of the phy reference counter
below zero and thus consecutive inserts of the module fails.
This patch removes calls to s3c_hsotg_phy_disable from s3c_hsotg_remove
and s3c_hsotg_udc_stop.
s3c_hsotg_udc_stop is called from udc-core.c only after
usb_gadget_disconnect, which in turn calls s3c_hsotg_pullup, which
already calls s3c_hsotg_phy_disable.
s3c_hsotg_remove must be called only after udc_stop, so there is no
point in disabling phy once again there.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a queue is registered, the block layer turns off the bypass
setting (because bypass is enabled when the queue is created). This
doesn't work well for queues that are unregistered and then registered
again; we get a WARNING because of the unbalanced calls to
blk_queue_bypass_end().
This patch fixes the problem by making blk_register_queue() call
blk_queue_bypass_end() only the first time the queue is registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tejun Heo <tj@kernel.org>
CC: James Bottomley <James.Bottomley@HansenPartnership.com>
CC: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@fb.com>
On systems with special thermal configurations make sure we make
note of the thermal setup. This is required for proper firmware
configuration on these systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
There is no need to use hex_dump_to_buffer() since we have a kernel helper to
dump up to 64 bytes just via printk(). In our case the actual size is 15 bytes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
PM entries of LPSS power domain were not implemented correctly
in commit c78b083066 "ACPI / LPSS: custom power domain for LPSS".
This patch fixes and completes these PM entries.
Fixes: c78b083066 (ACPI / LPSS: custom power domain for LPSS)
Signed-off-by: Li Aubrey <aubrey.li@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 232de51437 ("ACPI / battery: fix wrong value of
capacity_now reported when fully charged")
There is nothing wrong or unexpected about 'capacity_now' increasing above
the last 'full_charge_capacity' value. Different charging cycles will cause
'full_charge_capacity' to vary, both up and down. Good battery firmwares
will update 'full_charge_capacity' when the current charging cycle is
complete, increasing it if necessary. It might even go above
'design_capacity' on a fresh and healthy battery.
Capping 'capacity_now' to 'full_charge_capacity' is plain wrong, and
printing a warning if this doesn't happen to match the 'design_capacity'
is both annoying and terribly wrong.
This results in bogus warnings on perfectly working systems/firmwares:
[Firmware Bug]: battery: reported current charge level (39800) is higher than reported maximum charge level (39800).
and wrong values being reported for 'capacity_now' and
'full_charge_capacity' after the warning has been triggered.
Fixes: 232de51437 ("ACPI / battery: fix wrong value of capacity_now reported when fully charged")
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit d719870b41 ("ACPI / battery: Fix warning message in
acpi_battery_get_state()")
Capping 'capacity_now' to 'full_charge_capacity' is plain wrong. If this
is necessary to work around some buggy firmware, then the workaround needs
protection against being applied to working firmwares.
Good battery firmwares will allow 'capacity_now' to increase above
'full_charge_capacity', and will update the latter when the battery
is fully charged. By capping 'capacity_now' we lose accurate capacity
reporting until charging is complete whenever 'full_charge_capacity'
needs to be increased.
Fixes: d719870b41 ("ACPI / battery: Fix warning message in acpi_battery_get_state()")
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When DYNAMIC_DEBUG enabled, pr_debug() depends on KBUILD_MODNAME which
also depends on the modules number in Makefile. The related information
in "scripts/Makefile.lib" line 94:
# $(modname_flags) #defines KBUILD_MODNAME as the name of the module it will
# end up in (or would, if it gets compiled in)
# Note: Files that end up in two or more modules are compiled without the
# KBUILD_MODNAME definition. The reason is that any made-up name would
# differ in different configs.
For this case, 'radio-si470x-i2c.o' and 'radio-si470x-common.o' are in
one line, so cause compiling issue. And 'uaccess.h' is a common shared
header (not specially for drivers), so use pr_devel() instead of is OK.
The related error with allmodconfig:
CC [M] drivers/media/radio/si470x/radio-si470x-i2c.o
CC [M] drivers/media/radio/si470x/radio-si470x-common.o
In file included from include/linux/printk.h:257:0,
from include/linux/kernel.h:13,
from drivers/media/radio/si470x/radio-si470x.h:29,
from drivers/media/radio/si470x/radio-si470x-common.c:115:
./arch/microblaze/include/asm/uaccess.h: In function 'access_ok':
include/linux/dynamic_debug.h:66:14: error: 'KBUILD_MODNAME' undeclared (first use in this function)
.modname = KBUILD_MODNAME, \
^
include/linux/dynamic_debug.h:76:2: note: in expansion of macro 'DEFINE_DYNAMIC_DEBUG_METADATA'
DEFINE_DYNAMIC_DEBUG_METADATA(descriptor, fmt); \
^
include/linux/printk.h:263:2: note: in expansion of macro 'dynamic_pr_debug'
dynamic_pr_debug(fmt, ##__VA_ARGS__)
^
./arch/microblaze/include/asm/uaccess.h:101:3: note: in expansion of macro 'pr_debug'
pr_debug("ACCESS fail: %s at 0x%08x (size 0x%x), seg 0x%08x\n",
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
"entry.h" needs 'asmlinkage', and "asm/linkage.h" does not provide it.
So need include "linux/linkage.h" to use generic one instead of.
The related error (with allmodconfig under microblaze):
CC [M] drivers/net/ethernet/emulex/benet/be_main.o
In file included from ./arch/microblaze/include/asm/processor.h:17:0,
from include/linux/prefetch.h:14,
from drivers/net/ethernet/emulex/benet/be_main.c:18:
./arch/microblaze/include/asm/entry.h:33:19: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'void'
extern asmlinkage void do_notify_resume(struct pt_regs *regs, int in_syscall);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch wires up three new syscalls for powerpc. The three
new syscalls are seccomp, getrandom and memfd_create.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
CONFIG_FHANDLE is a requirement for systemd and with the increasing
uptake of systemd within distros it makes sense for 64 bit defconfigs
to include it.
Signed-off-by: Cyril Bur <cyril.bur@au1.ibm.com>
As opal_message_init() uses machine_early_initcall(powernv, ), and
opal_hmi_handler_init() depends on that early initcall, so it also needs
use machine_* to check the machine_id.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
ABIv2 kernels are failing to backtrace through the kernel. An example:
39.30% readseek2_proce [kernel.kallsyms] [k] find_get_entry
|
--- find_get_entry
__GI___libc_read
The problem is in valid_next_sp() where we check that the new stack
pointer is at least STACK_FRAME_OVERHEAD below the previous one.
ABIv1 has a minimum stack frame size of 112 bytes consisting of 48 bytes
and 64 bytes of parameter save area. ABIv2 changes that to 32 bytes
with no paramter save area.
STACK_FRAME_OVERHEAD is in theory the minimum stack frame size,
but we over 240 uses of it, some of which assume that it includes
space for the parameter area.
We need to work through all our stack defines and rationalise them
but let's fix perf now by creating STACK_FRAME_MIN_SIZE and using
in valid_next_sp(). This fixes the issue:
30.64% readseek2_proce [kernel.kallsyms] [k] find_get_entry
|
--- find_get_entry
pagecache_get_page
generic_file_read_iter
new_sync_read
vfs_read
sys_read
syscall_exit
__GI___libc_read
Cc: stable@vger.kernel.org # 3.16+
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Values acquired from Open Firmware are in 32-bit big endian format
and need to be handled on little endian architectures. This patch
ensures values are in cpu endian when hotplugging memory.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
The tx_empty() callback currently checks the TXEMPTY bit in the interrupt
status register to decided whether the FIFO should be reported as empty or
not. The bit in this register gets set when the FIFO state transitions from
non-empty to empty but is cleared again in the interrupt handler. This means
it is not suitable to be used to decided whether the FIFO is currently empty
or not. Instead use the TXEMPTY bit from the status register which will be
set as long as the FIFO is empty.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In set_termios(), interrupts where not disabled if UART_ENABLE_MS() was
false.
Tested on at91sam9g35.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org> # >= 3.16
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another new ACPI identifier for the 8250 dw bindings to cover newer Intel
SoCs such as Braswell.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the uwb_dev->bce entry is set before calling uwb_dev_add in
uwbd_dev_onair so that usermode will only see the device after it is
properly initialized. This fixes a kernel panic that can occur if
usermode tries to access the IEs sysfs attribute of a UWB device before
the driver has had a chance to set the beacon cache entry.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ext4 bugfix from Ted Ts'o.
[ Hmm. It's possible we should make kfree() aware of error pointers,
and use IS_ERR_OR_NULL rather than a NULL check. But in the meantime
this is obviously the right fix. - Linus ]
* 'for_linus_urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid trying to kfree an ERR_PTR pointer
Silence checkpatch warning:
WARNING: type 'long long unsigned' should be specified in
[[un]signed] [short|int|long|long long] order
Signed-off-by: Eddie Kovsky <ewk@edkovsky.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible for dev_alloc_skb() to fail. Propagate the error to the caller,
so it can clean up and drop the packet. The sender should end up retransmitting
the packet, hopefully at a time we're prepared to allocate skb's again.
Reported-By: Nicholas Krause <xerofoify@gmail.com>
Signed-Off-By: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull nfsd bugfixes from Bruce Fields:
"A couple minor nfsd bugfixes"
* 'for-3.17' of git://linux-nfs.org/~bfields/linux:
lockd: fix rpcbind crash on lockd startup failure
nfsd4: fix rd_dircount enforcement
Use the correct register address for Calibration Active and Interrupt
Enable.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I've not done a full audit of all mouse drivers, I noticed these ones were
missing the POINTER property while working on the POINTING_STICK property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is useful for userspace to know that there not dealing with a regular
mouse but rather with a pointing stick (e.g. a trackpoint) so that
userspace can e.g. automatically enable middle button scrollwheel
emulation.
It is impossible to tell the difference from the evdev info without
resorting to putting a list of device / driver names in userspace, this is
undesirable.
Add a property which allows userspace to see if a device is a pointing
stick, and set it on all the pointing stick drivers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sage Weil