The RTC module on the A64 was claimed to be the same as on the A31, when
in fact it is not. It is actually compatible to the H3's RTC. The A64's
RTC has some extra crypto-related registers which the H3's does not, but
the exact function of these is not clear.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The device node for the internal oscillator is
removed, as it is internalized into the RTC device. Clock references to
the IOSC and LOSC are also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This adds the Video Engine node for the A64. Since it can map the whole
DRAM range, there is no particular need for a reserved memory node
(unlike platforms preceding the A33).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the description for the SRAM C1 section to the A64 device-tree.
Since there is no entry for this section in the A64 manual, the base
address and size were only verified to be consistent empirically.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add nodes for i2s, digital and analog parts of audiocodec on A64.
The routing paths listed are entries connecting the digital and analog
side of the audio codec together. Due to how device tree works, these
must be copied over to each board device tree, in addition to any board
level routes.
The oversampling rate is set to 128, so that when playing back 192 kHz
audio samples, the MCLK runs at the same rate as the module clock, at
24.576 MHz.
The user manual suggests using different oversampling rates for different
sample rates, but that's not possible without a platform-specific machine
driver.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[wens@csie.org: Lowered oversampling rate to 128; expanded commit message]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add support for Allwinner A64 has Mali-400MP2.
All interrupt lines are mentioned in the manual so used the same.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A64 have a display pipeline with 2 mixers/TCONs, the first
TCON is connected to LCD and the second is to HDMI.
The HDMI controller/PHY pair is similar to the one on H3/H5.
Add all required device tree nodes of the display pipeline, including
the TCON0 LCD one and the TCON1 HDMI one.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: refactor commit message and add 1st pipeline]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pinmux name and label for a specific function should denote which
pingroup it is on, or if there is only one option for the function, have
not enumerating prefix/suffix at all.
The "r_i2c_pins_a" label is renamed to "r_i2c_pl89_pins" to fit our
current style. The node name "i2c" is also changed to "r-i2c-pl89-pins"
to match. The reason for the peculiar name is that the other option for
muxing R_I2C is on the PL0/PL1 pins, so the name has to mention the pin
numbers in addition to the pingroup.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pinmux name and label for a specific function should denote which
pingroup it is on, or if there is only one option for the function, have
not enumerating prefix/suffix at all.
The "uart0_pins_a" label is renamed to "uart0_pb_pins" to fit our
current style. The node name "uart0" is also changed to "uart0-pb-pins"
to match.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The eMMC 5.0 standard introduced the data strobe (DS) pin. This pin is
not used for pre-5.0 data modes, nor is it found on pre-5.0 eMMC chips.
On the A64, this pin is muxed with spi0's MISO pin. If the DS pin is
included in the mmc2 pinmux by default, this wil prevent the usage
of both mmc2 and spi0 together.
Instead, split out the DS pin to a separate pinmux that only gets used
by boards that actually have it wired up. Currently supported ones
include the Bananapi M64 and Pine64 Pinebook. These are fixed up.
Fixes: a3e8f49262 ("arm64: allwinner: a64: Add MMC pinctrl nodes")
Fixes: b8bcf0e1b2 ("arm64: allwinner: add BananaPi-M64 support")
Fixes: df35fbcfa3 ("arm64: dts: allwinner: add support for Pinebook")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Current kernels complain when booting on an A64 Soc:
....
[ 1.904297] cacheinfo: Unable to detect cache hierarchy for CPU 0
....
Not a real biggie on this flat topology, but also easy enough to fix.
Add the L2 cache node and let each CPU point to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The A64 have a SID controller which consist of EFUSE (starting at 0x200)
and three registers to read/write some of the protected efuses.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
address-cells/size-cells is unnecessary for dwmac-sun8i node.
It was in early days, but since a mdio node is used, it could be
removed.
This patch fix the following DT warning:
Warning (avoid_unnecessary_addr_size): /soc/ethernet@1c50000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As the U-Boot bootloader now is also capable of initialize the HDMI on
A64 boards, add a simplefb device tree node for accessing the HDMI
framebuffer initialized by the bootloader.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As we have all necessary parts to enable the DE2 CCU on the Allwinner
A64 SoC, add the needed device tree nodes, including the DE2 CCU itself
and the DE2 bus.
The "mixer0-lcd0" simplefb device node is updated to use the DE2 CCU.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A64 has a SRAM controller, and in the device tree currently
we have a syscon node to enable EMAC driver to access the EMAC clock
register. As SRAM controller driver can now export regmap for this
register, replace the syscon node to the SRAM controller device node,
and let EMAC driver to acquire its EMAC clock regmap.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Updated compatible string]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Allwinner A64 SoC features two PWM controllers, which are fully
compatible to the one used in the A13 and H3 chips.
Add the nodes for the devices (one for the "normal" PWM, the other for
the one in the CPUS domain) and the pins their outputs are connected to.
On the A64 the "normal" PWM is muxed together with one of the MDIO pins
used to communicate with the Ethernet PHY, so it won't be usable on many
boards. But the Pinebook laptop uses this pin for controlling the LCD
backlight.
On Pine64 the CPUS PWM pin however is routed to the "RPi2" header,
at the same location as the PWM pin on the RaspberryPi.
Tested on Pinebook and Teres-I
[vasily: fixed comment message as requested by Stefan Bruens, added default
muxing options to pwm and r_pwm nodes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.
Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Outside of SOC few chips need external clock source
through RTC example Wifi chip. So RTC clock nodes to
phandle 32kHz external oscillator.
prefix rtc- with clock-output-names defined in
dt-binding to avoid confusion with existing osc32k name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A64 SoC features two display pipelines, one has a LCD output, the
other has a HDMI output.
Add support for simplefb for the LCD output. Tested on Teres I.
This patch was inspired by work of Icenowy Zheng.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add a watchdog node for the A64, automatically enabled on all boards.
Since the device is compatible with an existing driver, we only reserve
a new compatible string to be used together with the fall back.
Tested on Olimex Teres-I.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the proper pin group node to reference in board files.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the DAI blocks to the device tree. I2S0 and I2S1 are for
connecting to an external codec.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the device tree sound bindings for the S/PDIF block.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF transceiver controller block and pin to the A64 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
stmmac bindings docs said that its mdio node must have
compatible = "snps,dwmac-mdio";
Since dwmac-sun8i does not have any good reasons to not doing it, all
their MDIO node must have it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore arm64 DT about dwmac-sun8i for A64
This reverts commit 87e1f5e8bb ("arm64: dts: allwinner: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The spi controller nodes omit the dma controller/channel references, add
it.
This does not yet enable DMA for SPI transfers, as the spi-sun6i driver
lacks support for DMA, but always uses PIO to the FIFO.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A64 SoC has a DMA controller that supports 8 DMA channels
to and from various peripherals. The last used DRQ port is 27.
Add a device node for it.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch fix the warning "xxx has a unit name, but no reg property" by
removing "@0" from such node
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This patch remove leading 0 of unit address and so remove
lots of warning when building DT with W=1.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The A64 SPI controllers are register compatible to the h3/h5 SPI
controllers.
The A64 has two SPI controllers, each with a single chip select.
The handles for the DMA channels (23/24 for SPI0/SPI1) are omitted,
as the A64 DMA support is currently missing.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The usual improvement patches:
- R_INTC interrupt controller enabled for the A64 SoC
- AXP803 PMIC added and enabled on the Pine64 and SoPine boards
-----BEGIN PGP SIGNATURE-----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=9oen
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Pull "Allwinner arm64 DT changes for 4.14" from Chen-Yu Tsai:
The usual improvement patches:
- R_INTC interrupt controller enabled for the A64 SoC
- AXP803 PMIC added and enabled on the Pine64 and SoPine boards
* tag 'sunxi-dt64-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: a64: add AXP803 PMIC support to SoPine and the baseboard
arm64: allwinner: a64: enable AXP803 regulators for Pine64
arm64: allwinner: a64: add DTSI file for AXP803 PMIC
arm64: allwinner: a64: add AXP803 node to Pine64 device tree
arm64: allwinner: a64: add NMI (R_INTC) controller on A64
The datasheet said that emac register size is 0x10000 not 0x100
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Fixed commit subject prefix]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner A64 SoC features a R_INTC controller, which controls the NMI
line, and this interrupt line is usually connected to the AXP PMIC.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Add fallback sun6i-a31-r-intc compatible]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device-tree updates for arm64 platforms. For the first time I can
remember, this is actually larger than the corresponding branch for
32-bit platforms overall, though that has more individual changes.
A significant portion this time is due to added machine support:
- Initial support for the Realtek RTD1295 SoC, along with the Zidoo
X9S set-top-box
- Initial support for Actions Semi S900 and the Bubblegum-96
single-board-cёmputer.
- Rockchips support for the rk3399-Firefly single-board-computer
gets added, this one stands out for being relatively fast,
affordable and well₋supported, compared to many boards that
only fall into one or two of the above categories.
- Mediatek gains support for the mt6797 mobile-phone SoC platform
and corresponding evaluation board.
- Amlogic board support gets added for the NanoPi K2 and S905x
LibreTech CC single-board computers and the R-Box Pro set-top-box
- Allwinner board support gets added for the OrangePi Win,
Orangepi Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single
board computers and the SoPine system-on-module.
- Renesas board support for Salvator-XS and H3ULCB
automotive development systems.
- Socionext Uniphier board support for LD11-global and LD20-global,
whatever those may be.
- Broadcom adds support for the new Stingray communication processor
in its iProc family, along with two reference boards.
Other updates include:
- For the hisicon platform, support for Hi3660-Hikey960 gets
extended significantly.
- Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=E8pa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"Device-tree updates for arm64 platforms. For the first time I can
remember, this is actually larger than the corresponding branch for
32-bit platforms overall, though that has more individual changes.
A significant portion this time is due to added machine support:
- Initial support for the Realtek RTD1295 SoC, along with the Zidoo
X9S set-top-box
- Initial support for Actions Semi S900 and the Bubblegum-96
single-board-cёmputer.
- Rockchips support for the rk3399-Firefly single-board-computer gets
added, this one stands out for being relatively fast, affordable
and well₋supported, compared to many boards that only fall into one
or two of the above categories.
- Mediatek gains support for the mt6797 mobile-phone SoC platform and
corresponding evaluation board.
- Amlogic board support gets added for the NanoPi K2 and S905x
LibreTech CC single-board computers and the R-Box Pro set-top-box
- Allwinner board support gets added for the OrangePi Win, Orangepi
Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single board computers
and the SoPine system-on-module.
- Renesas board support for Salvator-XS and H3ULCB automotive
development systems.
- Socionext Uniphier board support for LD11-global and LD20-global,
whatever those may be.
- Broadcom adds support for the new Stingray communication processor
in its iProc family, along with two reference boards.
Other updates include:
- For the hisicon platform, support for Hi3660-Hikey960 gets extended
significantly.
- Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (243 commits)
ARM64: dts: marvell: armada37xx: Fix timer interrupt specifiers
Revert "arm64: dts: marvell: add dma-mask in crypto nodes for 7k/8k"
arm64: dts: mediatek: don't include missing file
ARM64: dts: meson-gxl: Add Libre Technology CC support
dt-bindings: arm: amlogic: Add Libre Technology CC board
dt-bindings: add Libre Technology vendor prefix
arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K
arm64: dts: zte: Use - instead of @ for DT OPP entries
arm64: dts: marvell: add gpio support for Armada 7K/8K
arm64: dts: marvell: add pinctrl support for Armada 7K/8K
arm64: dts: marvell: use new binding for the system controller on cp110
arm64: dts: marvell: remove *-clock-output-names on cp110
arm64: dts: marvell: use new bindings for xor clocks on ap806
arm64: dts: marvell: mcbin: enable the mdio node
arm64: dts: Add Actions Semi S900 and Bubblegum-96
dt-bindings: Add vendor prefix for uCRobotics
arm64: dts: marvell: add xmdio nodes for 7k/8k
arm64: dts: marvell: add a comment on the cp110 slave node status
arm64: dts: marvell: remove cpm crypto nodes from dts files
arm64: dts: marvell: cp110: enable the crypto engine at the SoC level
...
The dwmac-sun8i is an Ethernet MAC that supports 10/100/1000 Mbit
connections. It is very similar to the device found in the Allwinner
H3, but lacks the internal 100 Mbit PHY and its associated control
bits.
This adds the necessary bits to the Allwinner A64 SoC .dtsi, but keeps
it disabled at this level.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch add the dt node for the syscon register present on the
Allwinner A64.
Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A64 device tree file has some remnants of raw number references
to the CCU node, likely from when the CCU bindings and device tree
changes were first merged.
Convert these, and the R_CCU ones, to use the proper defined macros
from their respective device tree binding header files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pine64 exposes all A64 UARTs, not just UART0.
Since the pins can be used as GPIO, don't enable the new UART nodes by
default, but prepare the pinctrl settings to aid in activating them via
overlays, i.e., overriding the status property of &uartX nodes.
For UART4 (Euler) the safer route of not including RTS/CTS pins is chosen,
whereas for UART1 (Bluetooth) they are included.
Add the corresponding pinctrl nodes where missing.
Suggested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 have a RSB controller like the one on A23/A33 SoCs.
Add it and its pinmux.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UART2 is exposed on the Pi connector of Pine64. Make a pinctrl node
available at the SoC level, to simplify enabling UART2 via DT overlay.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AR100 clock within the R_CCU (PRCM) has the PLL_PERIPH0 as one of
its parents.
This adds the reference in the device tree describing this relationship.
This patch uses a raw number for the clock index to ease merging by
avoiding cross tree dependencies.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 SoC features a pair of EHCI/OHCI controllers that can be
set to wire to USB0 port (the OTG-capable one), which can be used to
provide a better performance in host mode.
Add their device tree nodes.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch of smaller
changes, but also some new platforms that are worth mentioning:
* Rockchip RK3399 platforms for Chromebooks, including Samsung Chromebook
Plus (Kevin)
* Orange Pi PC2 (Allwinner H5)
* Freescale LS2088A and LS1088A SoCs
* Expanded support for Nvidia Tegra186 (and Jetson TX2)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q3Ix
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
The USB PHY in A64 has a "pmu0" region, which controls the EHCI/OHCI
controller pair that can be connected to the PHY0.
Add the MMIO region for PHY node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 have a dedicated pin controller to manage the PL pin bank.
As the driver and the required clock support are added, add the device
node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A64 SoC have a CCU (r_ccu) in PRCM block.
Add the device node for it.
The mux 3 of R_CCU is an internal oscillator, which is 16MHz according
to the user manual, and has only 30% accuracy based on our experience
on older SoCs. The real mesaured value of it on two Pine64 boards is
around 11MHz, which is around 70% of 16MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On many boards UART1 connects to a Bluetooth chip, so add the pinctrl
nodes for the only pins providing access to that UART. That includes
those pins for hardware flow control (RTS/CTS).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Chen-Yu Tsai