This patch fixes the sensor platform data initialisation for st_pressure
and st_accel device drivers. Without this patch, the driver fails to
register the sensors when the user removes and re-loads the driver.
1. Unload the kernel modules for st_pressure
$ sudo rmmod st_pressure_i2c
$ sudo rmmod st_pressure
2. Re-load the driver
$ sudo insmod st_pressure
$ sudo insmod st_pressure_i2c
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch initializes the bootime in struct st_sensor_settings for
lps22hb sensor. Without this, sensor channels read from sysfs always
report stale values.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Both devices are using the same iio_chan_spec to define which settings
are exported with sysfs. Both are properly configured to set/get
sampling frequency for pressure and temperature. They also properly
export available sampling frequencies. The only missing thing is
sampling_frequency sysfs file, which allows to set/get this property
from userspace.
Add sampling frequency to iio channel info mask, so sampling_frequency
file is properly exported using sysfs.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Datasheet of each device (lps331ap, lps25h, lps001wp, lps22hb) says that
the pressure and temperature data is a 2's complement.
I'm sending this the slow way, as negative pressures on these are pretty
unusual and the nature of the fixing of multiple device introduction patches
will make it hard to apply to older kernels - Jonathan.
Fixes: 217494e5b7 ("iio:pressure: Add STMicroelectronics pressures driver")
Fixes: 2f5effcbd0 ("iio: pressure-core: st: Expand and rename LPS331AP's channel descriptor")
Fixes: 7885a8ce68 ("iio: pressure: st: Add support for new LPS001WP pressure sensor")
Fixes: e039e2f5b4 ("iio:st_pressure:initial lps22hb sensor support")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We have #defines for all the individual sensor registers and
value/mask pairs #defined at the top of the file and used at
exactly one spot.
This is usually good if the #defines give a meaning to the
opaque magic numbers.
However in this case, the semantic meaning is inherent in the
name of the C99-addressable fields, and that means duplication
of information, and only makes the code hard to maintain since
you every time have to add a new #define AND update the site
where it is to be used.
Get rid of the #defines and just open code the values into the
appropriate struct elements. Make sure to explicitly address
the .hz and .value fields in the st_sensor_odr_avl struct
so that the meaning of all values is clear.
This patch is purely syntactic should have no semantic effect.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some static channels are explicitly initialized with default values.
Remove them to enhance readability.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable support for triggered buffering of temperature samples.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Details scaling factors and offsets applied to raw temperature and pressure
samples.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Sampled pressure data are 24 bits long and should be stored in a 32 bits
word.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98ad8b41f58dff6b30713d7f09ae3834b8df7ded
("iio: st_sensors: verify interrupt event to status") caused
a regression when reading ST sensors from a HRTimer trigger
rather than the intrinsic interrupts: the HRTimer may
trigger faster than the sensor provides new values, and
as the check against new values available as a cause of
the interrupt trigger was done in the poll function,
this would bail out of the HRTimer interrupt with
IRQ_NONE.
So clearly we need to only check the new values available
from the proper interrupt handler and not from the poll
function, which should rather just read the raw values
from the registers, put them into the buffer and be happy.
To achieve this: switch the ST Sensors over to using a true
threaded interrupt handler.
In the interrupt thread, check if new values are available,
else yield to the (potential) next device on the same
interrupt line to check the registers. If the interrupt
was ours, proceed to poll the values.
Instead of relying on iio_trigger_generic_data_rdy_poll() as
a top half to wake up the thread that polls the sensor for
new data, have the thread call iio_trigger_poll_chained()
after determining that is is the proper source of the
interrupt. This is modelled on drivers/iio/accel/mma8452.c
which is already using a properly threaded interrupt handler.
In order to get the same precision in timestamps as
previously, where samples would be timestamped in the
poll function pf->timestamp when calling
iio_trigger_generic_data_rdy_poll() we introduce a
local timestamp in the sensor data, set it in the top half
(fastpath) of the interrupt handler and provide that to the
core when calling iio_push_to_buffers_with_timestamp().
Additionally: if the active scanmask is not set for the
sensor no IRQs should be enabled and we need to bail out
with IRQ_NONE. This can happen if spurious IRQs fire when
installing the threaded interrupt handler.
Tested with hard interrupt triggers on LIS331DL, then also
tested with hrtimers on the same sensor by creating a 75Hz
HRTimer and using it to poll the sensor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Fixes: 97865fe413 ("iio: st_sensors: verify interrupt event to status")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure failure to enable power regulators is properly handled.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Temperature channels report scaled samples in Celsius although expected as
milli degree Celsius in Documentation/ABI/testing/sysfs-bus-iio.
Gains are not implemented at all for LPS001WP pressure and temperature
channels.
This patch ensures that proper offsets and scales are exposed to userpace
for both pressure and temperature channels.
Also fix a NULL pointer exception when userspace reads content of sysfs
scale attribute when gains are not defined.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initial support for ST LPS22HB pressure sensor. Datasheet:
http://www2.st.com/resource/en/datasheet/lps22hb.pdf
Features:
* pressure data and timestamping channels
* sampling frequency selection
* interrupt based trigger
* over I2C or SPI
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some types of ST Sensors can be connected to the same IRQ line
as other peripherals using open drain. Add a device tree binding
and a sensor data property to flip the right bit in the interrupt
control register to enable open drain mode on the INT line.
If the line is set to be open drain, also tag on IRQF_SHARED
to the IRQ flags when requesting the interrupt, as the whole
point of using open drain interrupt lines is to share them with
more than one peripheral (wire-or).
Cc: devicetree@vger.kernel.org
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Rob Herring <rob@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This makes all ST sensor drivers check that they actually have
new data available for the requested channel(s) before claiming
an IRQ, by reading the status register (which is conveniently
the same for all ST sensors) and check that the channel has new
data before proceeding to read it and fill the buffer.
This way sensors can share an interrupt line: it can be flaged
as shared and then the sensor that did not fire will return
NO_IRQ, and the sensor that fired will handle the IRQ and
return IRQ_HANDLED.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Most ST MEMS Sensors that support interrupts can also handle sending
an active low interrupt, i.e. going from high to low on data ready
(or other interrupt) and thus triggering on a falling edge to the
interrupt controller.
Set up logic to inspect the interrupt line we get for a sensor: if
it is triggering on rising edge, leave everything alone, but if it
triggers on falling edges, set up active low, and if unsupported
configurations appear: warn with errors and reconfigure the interrupt
to a rising edge, which all interrupt generating sensors support.
Create a local header for st_sensors_core.h to share functions
between the sensor core and the trigger setup code.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds a debugfs hook to read/write registers in the ST
sensors using debugfs. Proved to be awesome help when trying
to debug why IRQs do not arrive.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch permits to configure the WhoAmI register address
because some device could have not a standard address for
this register.
Signed-off-by: Giuseppe Barba <giuseppe.barba@st.com>
Reviewed-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In SPI mode the transfer buffer is locked with a mutex. However this
mutex is only initilized after the probe, but some transfer needs to
be done in the probe.
To fix this bug we move the mutex initialization at the beginning of
the device probe.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fix pressure data variable name. Usually pdata name
it is used for platform data.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch change structure name and related variables names.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This allows in kernel client drivers to access this
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Currently the pressure sensor has code to retrieve and enable two
regulators for Vdd and Vdd IO, but actually these voltage inputs
are found on all of these ST sensors, so move the regulator
handling to the core and make sure all the ST sensors call these
functions on probe() and remove() to enable/disable power.
Here also mover over to obtaining the regulator from the *parent*
device of the IIO device, as the IIO device is created on-the-fly
in this very subsystem it very unlikely evert have any regulators
attached to it whatsoever. It is much more likely that the parent
is a platform device, possibly instantiated from a device tree,
which in turn have Vdd and Vdd IO supplied assigned to it.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It is pretty helpful to know already from dmesg that a certain
device is successfully registered, instead of having to browse
sysfs to see if it's actually there.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for the new barometer sensor: LPS25H.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The power to some of the sensors are controlled by regulators. In most
cases these are 'always on', but if not they will fail to work until
the regulator is enabled using the relevant APIs. This patch allows for
the Vdd_IO power supply to be specified by either platform data or
Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The power to some of the sensors are controlled by regulators. In most
cases these are 'always on', but if not they will fail to work until
the regulator is enabled using the relevant APIs. This patch allows for
the Vdd power supply to be specified by either platform data or Device
Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fix buffer registration that allows to use generic IIO trigger.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here we use existing practices to introduce support for another
pressure/temperature sensor, the LPS001WP.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch contains some pretty basic clean-ups in probe() pertaining to
the simplification of error handling and a couple of readability adaptions.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Not all ST's sensors support data ready, so let's make the declaration
of one conditional.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
At the moment the number of channels specified is dictated by the first
sensor supported by the driver. As we add support for more sensors this
is likely to vary. Instead of using the ARRAY_SIZE() of the LPS331AP's
channel specifier we'll use a new adaptable 'struct st_sensors' element
instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Due to the MACRO used, the task of reading, understanding and maintaining
the LPS331AP's channel descriptor is substantially difficult. This patch
is based on the view that it's better to have easy to read, maintainable
code than to save a few lines here and there. For that reason we're
expanding the array so initialisation is completed in full.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
They're currently named *_1_*, for 'Sensor 1', but the code will be much
more readable if we use the naming convention *_LPS331AP_* instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some chips either don't support it or fail to provide adequate documentation,
so sometimes it's impossible to enable the feature even if it is supported.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch modifies the way how the in_temp_scale output value is
calculated. With this implementation it is more clear how the value
is obtained.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch add support to redirect the DRDY interrupt on INT1 or INT2
on accelerometer and pressure sensors.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes improper in_pressure_scale output that is
returned by the lps331ap barometer sensor driver. According
to the documentation the pressure after applying the scale has to
be expressed in kilopascal units. With erroneous implementation
the scale value larger by two orders of magnitude is returned -
2441410 instead of 24414.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds a generic pressure driver for STMicroelectronics
pressure sensors, currently it supports: LPS331AP.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Shrirang Bagul