The headphone detect and charger are using the IRQ numbers so need
to take account of irq_base with the genirq conversion. I obviously
picked the wrong system for initial testing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq implementation does not allow modules to implement irq_chips
so the conversion of WM8350 to genirq means we can no longer allow the
driver to be built as a module.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This gives us use of the diagnostic facilities genirq provides and
will allow implementation of interrupt support for the WM8350 GPIOs.
Stub functions are provided to ease the transition of the individual
drivers, probably after additional work to pass the IRQ numbers via
the struct devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Unlike the wm8350-custom code genirq nests enable and disable calls
so we can't just unconditionally mask or unmask the interrupt,
we need to remember the state we set and only mask or unmask when
there is a real change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The structure t7l66xb should not be freed before the subsequent references
to its fields in the arguments to clk_put. Furthermore, this structure is
allocated near the beginning of the function, and a goto to the label
err_noirq appears after a successful allocation, so it would seem that the
kfree should be moved down below this label.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,e;
identifier f;
iterator I;
statement S;
@@
*kfree(x);
... when != &x
when != x = e
when != I(x,...) S
*x->f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Use resource_size() for ioremap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use resource_size() for ioremap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The requested memory region is smaller than the actual ioremap().
Use resource_size() to get the correct size.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The recent rework of /proc/bus/usb/devices polling support made
this structure unused so let's remove it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit a069c266ae.
It turns ou that not only was it missing a case (XFS) that needed it,
but perhaps more importantly, people sometimes want to enable new
modules that they hadn't had enabled before, and if such a module uses
list_sort(), it can't easily be inserted any more.
So rather than add a "select LIST_SORT" to the XFS case, just leave it
compiled in. It's not all _that_ big, after all, and the inconvenience
isn't worth it.
Requested-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Don Mullis <don.mullis@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The caller of usbfs_conn_disc_event() in some cases (but not always)
already holds usbfs_mutex, so trying to protect the event counter with
that lock causes nasty deadlocks.
The problem was introduced by commit 554f76962d ("USB: Remove BKL from
poll()") when the BLK protection was turned into using the mutex instead.
So fix this by using an atomic variable instead. And while we're at it,
get rid of the atrocious naming of said variable and the waitqueue it is
associated with.
This also cleans up the unnecessary locking in the poll routine, since
the whole point of how the pollwait table works is that you can just add
yourself to the waiting list, and then check the condition you're
waiting for afterwards - avoiding all races.
It also gets rid of the unnecessary dynamic allocation of the device
status that just contained a single word. We should use f_version for
this, as Dmitry Torokhov points out. That simplifies everything
further.
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm raid1: fix deadlock when suspending failed device
dm: eliminate some holes data structures
dm ioctl: introduce flag indicating uevent was generated
dm: free dm_io before bio_endio not after
dm table: remove unused dm_get_device range parameters
dm ioctl: only issue uevent on resume if state changed
dm raid1: always return error if all legs fail
dm mpath: refactor pg_init
dm mpath: wait for pg_init completion when suspending
dm mpath: hold io until all pg_inits completed
dm mpath: avoid storing private suspended state
dm: document when snapshot has finished merging
dm table: remove dm_get from dm_table_get_md
dm mpath: skip activate_path for failed paths
dm mpath: pass struct pgpath to pg init done
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (23 commits)
hwmon: Remove the deprecated adt7473 driver
hwmon: Fix off-by-one kind values
hwmon: (tmp421) Fix temperature conversions
hwmon: (tmp421) Restore missing inputs
hwmon: Driver for Andigilog aSC7621 family monitoring chips
hwmon: (adt7411) Improve locking
hwmon: Add driver for ADT7411 voltage and temperature sensor
hwmon: (w83793) Add watchdog functionality
hwmon: (g760a) Make rpm_from_cnt static
hwmon: (it87) Validate auto pwm settings
hwmon: (it87) Add support for old automatic fan speed control
hwmon: (it87) Drop dead web links in documentation
hwmon: (it87) Add an entry in MAINTAINERS
hwmon: (it87) Use strict_strtol instead of simple_strtol
hwmon: (it87) Fix many checkpatch errors and warnings
hwmon: (it87) Add support for beep on alarm
hwmon: (it87) Create vid attributes by group
hwmon: (it87) Refactor attributes creation and removal
hwmon: (it87) Expose the PWM/temperature mappings
hwmon: (it87) Display fan outputs in automatic mode as such
...
* git://git.infradead.org/ubi-2.6:
UBI: add write checking
UBI: simplify debugging return codes
UBI: fix attaching error path
UBI: support attaching by MTD character device name
UBI: mark few variables as __initdata
The cs5535-gpio driver's get() function was returning the output value.
This means that the GPIO pins would never work as an input, even if
configured as an input.
The driver should return the READ_BACK value, which is the sensed line
value. To make that work when the direction is 'output', INPUT_ENABLE
needs to be set.
In addition, the driver was not disabling OUTPUT_ENABLE when the direction
is set to 'input'. That would cause the GPIO to continue to drive the pin
if the direction was ever set to output.
This issue was noticed when attempting to use the gpiolib driver to read
an external input. I had previously been using the char/cs5535-gpio
driver.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@kernel.org> [2.6.33.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of the GPIO expanders controlled by the pca953x driver are able to
report changes on the input pins through an *INT pin.
This patch implements the irq_chip functionality (edge detection only).
The driver has been tested on an Arcom Zeus.
[akpm@linux-foundation.org: the compiler does inlining for us nowadays]
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce support for triggering interrupts on both rising and falling
edge.
This feature requires version 3 or newer of the IP, a version check is
done when triggering on both edges is requested.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gpio_request() without initial configuration of the GPIO is normally
useless, introduce gpio_request_one() together with GPIOF_ flags for
input/output direction and initial output level.
gpio_{request,free}_array() for multiple GPIOs.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the MAX7300-I2C variant of the MAX7301-SPI version. Both chips share
the same core logic, so the generic part of the in-kernel SPI-driver is
refactored into a generic part. The I2C and SPI specific funtions are
then wrapped into seperate drivers picking up the generic part.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The else part of the if statement is indented but does not have braces
around it. It clearly should since it uses clk_enable and clk_disable
which are supposed to balance.
Signed-off-by: James Hogan <james@albanarts.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is to protect from interrupt handlers using an unregistered rtc
device.
To assert that the reset irq is considered now before the rtc is
registered the corresponding status is checked before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver for the mc13783 rtc needs to know if the TODA irq is pending.
Instead of tracking in the rtc driver if the irq is enabled provide that
information, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mc13783_ackirq, mc13783_unmask and mc13783_mask are deprecated, use the
drop in replacements with the nicer names.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the source file group these functions together.
The mc13783 header file provides fallback implementations for the old
names to prevent build failures. When all users of the old names are
fixed to use the new names these can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The idr should be destroyed when the module is unloaded. Found with
kmemleak.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning of
the declaration specifiers in a declaration is an obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memset should be given the size of the structure, not the size of the
pointer.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
T *x;
expression E;
@@
memset(x, E, sizeof(
+ *
x))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function pcf2123_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Christian Pellegrin <chripell@fsfe.org>
Cc: Chris Verges <chrisv@cyberswitching.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix issue with rtc device not getting unregistered in probe error path.
Use the devres managed resource functions in the probe routine to cleanup
the error path.
Use sysfs_{create/remove}_group to add/remove the sysfs files.
Reduces the text size by 132 bytes, increases data by 12 bytes:
text data bss dec hex filename
- 937 124 0 1061 425 rtc-ep93xx.o
+ 805 136 0 941 3ad rtc-ep93xx.o
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Free pdata before exit. Found by cppcheck.
[yuasa@linux-mips.org: add missing iounmap()]
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the xen support drivers are displayed in the main Device Drivers
menu of the config tools instead of in their own sub-menu, so move them to
their own sub-menu, like the rest of the driver world uses.
This keeps the main Device Drivers menu from becoming messy.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
warning: symbol 'vgacon_text_mode_force' was not declared. Should it be static?
Signed-off-by: Thiago Farina <tfransosi@gmail.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BuraphaLinux reported that we will trigger a mm warning when we
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=65536, this is because mm cann't
allocate so many pages. We should limit the range of
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE, don't give a user any chance to
trigger that.
Reported-by: BuraphaLinux Server <buraphalinuxserver@gmail.com>
Tested-by: BuraphaLinux Server <buraphalinuxserver@gmail.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While testing an ADC121S021 in an embedded board with a S3C2142 SoC (ARM
core), I have found that the 'adcxx' driver does not handle correctly
single channel ADCs from this chip family. For single channel chips you
must only issue one read transfer for correct measurement.
Signed-off-by: Jose Miguel Goncalves <jose.goncalves@inov.pt>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
String constants that are continued on subsequent lines with \ will cause
spurious whitespace in the resulting output.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This card reader doesn't advertise, however DMA works well. Probably
windows SDHCI driver assumes that all readers support DMA and thus we see
that bug.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Norbert Preining <preining@logic.at>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kunmap_atomic() accepts a pointer to any location in the page so we do not
need the subtraction and cast.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We used to manage features and differences on a per-cpu basis. As several
cpus share the same mci revision, this patch aggregates cpus that have the
same IP revision in one defined constant. We use the
at91mci_is_mci1rev2xx() funtion name not to mess with newer Atmel sd/mmc
IP called "MCI2". _rev2 naming could have been confusing...
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the datasheets AT91SAM9261 does not support SDIO interrupts,
and AT91SAM9260/9263 have an erratum requiring 4bit mode while using slot
B for the interrupt to work.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is setting some max_ variables for the IO elevator, so the
elevator will put requests for large data blocks to the driver. This is
critical for
a) speed
and
b) wear leveling of the flash chip controller: Otherwise the controller
will treat the SD card badly with millions of single 4 KByte write
commands. This will lead to a shorter life time for the SD cards.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the read to use the DMA buffer as well. The old code was doing
double-buffering DMA with the PDC; no way to make it work. Replace it
with a single-PDC approach. It also simplify things removing the need for
a pre_dma_read() function.
[nicolas.ferre@atmel.com coding style modifications]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TX DMA buffer is allocated only once, because the
allocation/deallocation of the buffer for EACH chunk of data is
time-consuming and prone to memory fragmentation.
Using a coherent DMA buffer avoids extra data cache calls.
[nicolas.ferre@atmel.com: coding style modifications]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix two timeout errors, one for slow SDHC cards and one for slow users
while inserting SD cards.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes two pointer errors, one which leads to memory overwrites if used
with large chunks of data.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If no platform_data was givin to the device it's going to use it's default
platform data struct which has all fields initialized to zero. As a
result the driver is going to try to request gpio0 both as write protect
and card detect pin. Which of course will fail and makes the driver
unusable
Previously to the introduction of no_wprotect and no_detect the behavior
was to assume that if no platform data was given there is no write protect
or card detect pin. This patch restores that behavior.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
And bring them back to 4-bit mode during resume.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDIO cards may suspend while keeping function interrupts active
especially in the powered suspend case. Upon resume we need to kick the
SDIO interrupt thread to check for pending interrupts and to restart card
IRQ detection at the host controller level.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seen on a Marvell 8686 SDIO card and Via VX855 controller: we must avoid
sending CMD3/5/7 on a resume where power has been maintained, because the
8686 will refuse to respond to them and the MMC stack will give up on the
card.
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested with an XO v1.5 from OLPC.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series provides the core changes needed to allow SDIO cards to
remain powered and active while the host system is suspended, and let them
wake up the host system when needed. This is used to implement
wake-on-lan with SDIO wireless cards at the moment. Patches to add that
support to the libertas driver will be posted separately.
This patch:
Some SDIO cards have the ability to keep on running autonomously when the
host system is suspended, and wake it up when needed. This however
requires that the host controller preserve power to the card, and
configure itself appropriately for wake-up.
There is however 4 layers of abstractions involved: the host controller
driver, the MMC core code, the SDIO card management code, and the actual
SDIO function driver. To make things simple and manageable, host drivers
must advertise their PM capabilities with a feature bitmask, then function
drivers can query and set those features from their suspend method. Then
each layer in the suspend call chain is expected to act upon those bits
accordingly.
[akpm@linux-foundation.org: fix typo in comment]
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sdhci_set_adma_desc() is using byte-writes to write data in a specified
order into memory. Change to using __le16 for the two byte and __le32 for
the four byte cases and use the cpu_to_{le16,le32} to do the conversion
before writing.
This will reduce the size of the code and the number of writes as we no
longer need to chop the data up before writing.
As an example on ARM S3C64XX SoC, in little-endian configuration:
000000d4 <sdhci_set_adma_desc>:
- d8: e1a0c423 lsr ip, r3, #8
- dc: e1a0ec21 lsr lr, r1, #24
- e0: e1a04821 lsr r4, r1, #16
- e4: e1a05421 lsr r5, r1, #8
- e8: e1a06442 asr r6, r2, #8
- ec: e5c0c001 strb ip, [r0, #1]
- f0: e5c0e007 strb lr, [r0, #7]
- f4: e5c04006 strb r4, [r0, #6]
- f8: e5c05005 strb r5, [r0, #5]
- fc: e5c01004 strb r1, [r0, #4]
- 100: e5c06003 strb r6, [r0, #3]
- 104: e5c02002 strb r2, [r0, #2]
- 108: e5c03000 strb r3, [r0]
+ d4: e5801004 str r1, [r0, #4]
+ d8: e1c030b0 strh r3, [r0]
+ dc: e1c020b2 strh r2, [r0, #2]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code to write the ADMA descriptor into memory is repeated several
times throughout sdhci_adma_table_pre, and thus should be moved into a
common function. This will also be useful if the patch to make the write
more efficient is accepted.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDIO cards expect byte transfers not to exceed the configured block
transfer size. Add a quirk to that effect.
Patches to make use of this quirk will be sent separately.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hardcoded value doesn't really work for all cards.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The host/Kconfig file is only included when MMC is selected.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The local sg variable is only used with BF54x code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This prevents those without an Atmel chip having a line in kernel
configuration which says "Atmel SD/MMC Driver" without any option.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for 8bit MMC cards. The controller data width is configurable
depending on the wires setting in the platform data structure.
MMC 8bit is tested on OMAPL137 and MMC 4bit is tested on OMAPL138 EVM.
Signed-off-by: Vipin Bhandari <vipin.bhandari@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch solves nasty problem original driver has.
Original goal of the ricoh_mmc was to disable this device because then,
mmc cards can be read using standard SDHCI controller, thus avoiding
writing of yet another driver.
However, the act of disablement, makes other pci functions that belong to
this controller (xD and memstick) shift up one level, thus pci core has
now wrong idea about these devices.
To fix this issue, this patch moves the driver into the pci quirk section,
thus it is executes before the pci is enumerated, and therefore solving
that issue, also same sequence of commands is performed on resume for same
reasons.
Also regardless of the above, this way is cleaner. You still need to set
CONFIG_MMC_RICOH_MMC to enable this quirk
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Philip Langdale <philipl@overt.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Build list_sort() only for configs that need it -- those that don't save
~581 bytes (i386).
Signed-off-by: Don Mullis <don.mullis@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add adds a debugfs interface and additional failure modes to LKDTM to
provide similar functionality to the provoke-crash driver submitted here:
http://lwn.net/Articles/371208/
Crashes can now be induced either through module parameters (as before)
or through the debugfs interface as in provoke-crash.
The patch also provides a new "direct" interface, where KPROBES are not
used, i.e., the crash is invoked directly upon write to the debugfs
file. When built without KPROBES configured, only this mode is available.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Cc: M. Mohan Kumar <mohan@in.ibm.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>,
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The variable priv is initialized twice to the same (side effect-free)
expression. Drop one initialization.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@forall@
idexpression *x;
identifier f!=ERR_PTR;
@@
x = f(...)
... when != x
(
x = f(...,<+...x...+>,...)
|
* x = f(...)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the CS5535 MFGPT hrtimer kconfig option to be with the other MFGPT
options. This makes it easier to find and also removes it from the main
"Device Drivers" menu, where it should not have been.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorder struct menu_device to remove 8 bytes of padding on 64 bit builds.
Size drops from 136 to 128 bytes, so possibly needing one fewer cache
lines.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A memmap is a directory in sysfs which includes 3 text files: start, end
and type. For example:
start: 0x100000
end: 0x7e7b1cff
type: System RAM
Interface firmware_map_add was not called explicitly. Remove it and add
function firmware_map_add_hotplug as hotplug interface of memmap.
Each memory entry has a memmap in sysfs, When we hot-add new memory, sysfs
does not export memmap entry for it. We add a call in function add_memory
to function firmware_map_add_hotplug.
Add a new function add_sysfs_fw_map_entry() to create memmap entry, it
will be called when initialize memmap and hot-add memory.
[akpm@linux-foundation.org: un-kernedoc a no longer kerneldoc comment]
Signed-off-by: Shaohui Zheng <shaohui.zheng@intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename for_each_bit to for_each_set_bit in the kernel source tree. To
permit for_each_clear_bit(), should that ever be added.
The patch includes a macro to map the old for_each_bit() onto the new
for_each_set_bit(). This is a (very) temporary thing to ease the migration.
[akpm@linux-foundation.org: add temporary for_each_bit()]
Suggested-by: Alexey Dobriyan <adobriyan@gmail.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use of get_irq_chip_data() et al. requires including linux/irq.h
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To prevent deadlock, bios in the hold list should be flushed before
dm_rh_stop_recovery() is called in mirror_suspend().
The recovery can't start because there are pending bios and therefore
dm_rh_stop_recovery deadlocks.
When there are pending bios in the hold list, the recovery waits for
the completion of the bios after recovery_count is acquired.
The recovery_count is released when the recovery finished, however,
the bios in the hold list are processed after dm_rh_stop_recovery() in
mirror_presuspend(). dm_rh_stop_recovery() also acquires recovery_count,
then deadlock occurs.
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Eliminate a 4-byte hole in 'struct dm_io_memory' by moving 'offset' above the
'ptr' to which it applies (size reduced from 24 to 16 bytes). And by
association, 1-4 byte hole is eliminated in 'struct dm_io_request' (size
reduced from 56 to 48 bytes).
Eliminate all 6 4-byte holes and 1 cache-line in 'struct dm_snapshot' (size
reduced from 392 to 368 bytes).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Set a new DM_UEVENT_GENERATED_FLAG when returning from ioctls to
indicate that a uevent was actually generated. This tells the userspace
caller that it may need to wait for the event to be processed.
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Free the dm_io structure before calling bio_endio() instead of after it,
to ensure that the io_pool containing it is not referenced after it is
freed.
This partially fixes a problem described here
https://www.redhat.com/archives/dm-devel/2010-February/msg00109.html
thread 1:
bio_endio(bio, io_error);
/* scheduling happens */
thread 2:
close the device
remove the device
thread 1:
free_io(md, io);
Thread 2, when removing the device, sees non-empty md->io_pool (because the
io hasn't been freed by thread 1 yet) and may crash with BUG in mempool_free.
Thread 1 may also crash, when freeing into a nonexisting mempool.
To fix this we must make sure that bio_endio() is the last call and
the md structure is not accessed afterwards.
There is another bio_endio in process_barrier, but it is called from the thread
and the thread is destroyed prior to freeing the mempools, so this call is
not affected by the bug.
A similar bug exists with module unloads - the module may be unloaded
immediately after bio_endio - but that is more difficult to fix.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove unused parameters(start and len) of dm_get_device()
and fix the callers.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Only issue a uevent on a resume if the state of the device changed,
i.e. if it was suspended and/or its table was replaced.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If all mirror legs fail, always return an error instead of holding the
bio, even if the handle_errors option was set. At present it is the
responsibility of the driver underneath us to deal with retries,
multipath etc.
The patch adds the bio to the failures list instead of holding it
directly. do_failures tests first if all legs failed and, if so,
returns the bio with -EIO. If any leg is still alive and handle_errors
is set, do_failures calls hold_bio.
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch pulls the pg_init path activation code out of
process_queued_ios() into a new function.
No functional change.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When suspending the device we must wait for all I/O to complete, but
pg-init may be still in progress even after flushing the workqueue
for kmpath_handlerd in multipath_postsuspend.
This patch waits for pg-init completion correctly in
multipath_postsuspend().
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
m->queue_io is set to block processing I/Os, and it needs to be kept
while pg-init, which issues multiple path activations, is in progress.
But m->queue is cleared when a path activation completes without error
in pg_init_done(), even while other path activations are in progress.
That may cause undesired -EIO on paths which are not complete activation.
This patch fixes that by not clearing m->queue_io until all path
activations complete.
(Before the hardware handlers were moved into the SCSI layer, pg_init
only used one path.)
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
'suspended' flag in struct multipath was introduced to check whether
the multipath target is in suspended state, but the same check is
done through dm_suspended() now, so remove the flag and related code.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove the dm_get() in dm_table_get_md() because dm_table_get_md() could
be called from presuspend/postsuspend, which are called while
mapped_device is in DMF_FREEING state, where dm_get() is not allowed.
Justification for that is the lifetime of both objects: As far as the
current dm design/implementation, mapped_device is never freed while
targets are doing something, because dm core waits for targets to become
quiet in dm_put() using presuspend/postsuspend. So targets should be
able to touch mapped_device without holding reference count of the
mapped_device, and we should allow targets to touch mapped_device even
if it is in DMF_FREEING state.
Backgrounds:
I'm trying to remove the multipath internal queue, since dm core now has
a generic queue for request-based dm. In the patch-set, the multipath
target wants to request dm core to start/stop queue. One of such
start/stop requests can happen during postsuspend() while the target
waits for pg-init to complete, because the target stops queue when
starting pg-init and tries to restart it when completing pg-init. Since
queue belongs to mapped_device, it involves calling dm_table_get_md()
and dm_put(). On the other hand, postsuspend() is called in dm_put()
for mapped_device which is in DMF_FREEING state, and that triggers
BUG_ON(DMF_FREEING) in the 2nd dm_put().
I had tried to solve this problem by changing only multipath not to
touch mapped_device which is in DMF_FREEING state, but I couldn't and I
came up with a question why we need dm_get() in dm_table_get_md().
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds two minor fixes while processing device mapper path activation.
Skip failed paths while calling activate_path. If the path is already failed
then activate_path will fail for sure. We don't have to call in that case. In
some case this might cause prolonged retries unnecessarily.
Change the misleading message if the path being activated fails with SCSI_DH_NOSYS.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch removes some unnecessary argument casting. There is no
functional change with this patch.
Passes 'struct pgpath' through to pg_init_done() instead of the enclosed
'struct dm_path'.
Tested the changes with LSI storage..
CC: Chandra Seetharaman <chandra.seetharaman@us.ibm.com>
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: (33 commits)
quota: stop using QUOTA_OK / NO_QUOTA
dquot: cleanup dquot initialize routine
dquot: move dquot initialization responsibility into the filesystem
dquot: cleanup dquot drop routine
dquot: move dquot drop responsibility into the filesystem
dquot: cleanup dquot transfer routine
dquot: move dquot transfer responsibility into the filesystem
dquot: cleanup inode allocation / freeing routines
dquot: cleanup space allocation / freeing routines
ext3: add writepage sanity checks
ext3: Truncate allocated blocks if direct IO write fails to update i_size
quota: Properly invalidate caches even for filesystems with blocksize < pagesize
quota: generalize quota transfer interface
quota: sb_quota state flags cleanup
jbd: Delay discarding buffers in journal_unmap_buffer
ext3: quota_write cross block boundary behaviour
quota: drop permission checks from xfs_fs_set_xstate/xfs_fs_set_xquota
quota: split out compat_sys_quotactl support from quota.c
quota: split out netlink notification support from quota.c
quota: remove invalid optimization from quota_sync_all
...
Fixed trivial conflicts in fs/namei.c and fs/ufs/inode.c
adt7473 driver is obsoleted by adt7475 driver. And it is scheduled
to be removed in Feb 2010.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Recent changes on the I2C front have left off-by-one array indexes in
3 hwmon drivers. Fix them.
Faulty commit:
e5e9f44c2 i2c: Drop I2C_CLIENT_INSMOD_2 to 8
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andre Prendel <andre.prendel@gmx.de>
Cc: stable@kernel.org
The low bits of temperature registers are status bits, they must be
masked out before converting the register values to temperatures.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Andre Prendel <andre.prendel@gmx.de>
Cc: stable@kernel.org
An off-by-one error caused some inputs to not be created by the driver
when they should. TMP421 gets only one input instead of two, TMP422
gets two instead of three, etc. Fix the bug by listing explicitly the
number of inputs each device has.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Andre Prendel <andre.prendel@gmx.de>
Cc: stable@kernel.org
Hwmon driver for Andigilog aSC7621 family monitoring chips.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add proper locking for the cached variables. Also get rid of
ref_is_vdd, which became obsolete.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add basic support for the ADT7411. Reads out all conversion results (via I2C,
SPI yet missing) and allows some on-the-fly configuration. Tested with a
custom board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add watchdog functionality to the Winbond W83793 driver.
Signed-off-by: Sven Anders <anders@anduras.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Function rpm_from_cnt is only used internally so it can be made
static. Make it inline while we're here, for performance reasons
(although hopefully gcc would figure out by itself...)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Mark Brown