Looks like a quiet cycle for vhost/virtio, just a couple of minor
tweaks. Most notable is automatic interrupt affinity for blk and scsi.
Hopefully other devices are not far behind.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYt1rRAAoJECgfDbjSjVRpEZsIALSHevdXWtRHBZUb0ZkqPLQb
/x2Vn49CcALS1p7iSuP9L027MPeaLKyr0NBT9hptBChp/4b9lnZWyyAo6vYQrzfx
Ia/hLBYsK4ml6lEwbyfLwqkF2cmYCrZhBSVAILifn84lTPoN7CT0PlYDfA+OCaNR
geo75qF8KR+AUO0aqchwMRL3RV3OxZKxQr2AR6LttCuhiBgnV3Xqxffg/M3x6ONM
0ffFFdodm6slem3hIEiGUMwKj4NKQhcOleV+y0fVBzWfLQG9210pZbQyRBRikIL0
7IsaarpaUr7OrLAZFMGF6nJnyRAaRrt6WknTHZkyvyggrePrGcmGgPm4jrODwY4=
=2zwv
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull vhost updates from Michael Tsirkin:
"virtio, vhost: optimizations, fixes
Looks like a quiet cycle for vhost/virtio, just a couple of minor
tweaks. Most notable is automatic interrupt affinity for blk and scsi.
Hopefully other devices are not far behind"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-console: avoid DMA from stack
vhost: introduce O(1) vq metadata cache
virtio_scsi: use virtio IRQ affinity
virtio_blk: use virtio IRQ affinity
blk-mq: provide a default queue mapping for virtio device
virtio: provide a method to get the IRQ affinity mask for a virtqueue
virtio: allow drivers to request IRQ affinity when creating VQs
virtio_pci: simplify MSI-X setup
virtio_pci: don't duplicate the msix_enable flag in struct pci_dev
virtio_pci: use shared interrupts for virtqueues
virtio_pci: remove struct virtio_pci_vq_info
vhost: try avoiding avail index access when getting descriptor
virtio_mmio: expose header to userspace
When device IOTLB is enabled, all address translations were stored in
interval tree. O(lgN) searching time could be slow for virtqueue
metadata (avail, used and descriptors) since they were accessed much
often than other addresses. So this patch introduces an O(1) array
which points to the interval tree nodes that store the translations of
vq metadata. Those array were update during vq IOTLB prefetching and
were reset during each invalidation and tlb update. Each time we want
to access vq metadata, this small array were queried before interval
tree. This would be sufficient for static mappings but not dynamic
mappings, we could do optimizations on top.
Test were done with l2fwd in guest (2M hugepage):
noiommu | before | after
tx 1.32Mpps | 1.06Mpps(82%) | 1.30Mpps(98%)
rx 2.33Mpps | 1.46Mpps(63%) | 2.29Mpps(98%)
We can almost reach the same performance as noiommu mode.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If last avail idx is not equal to cached avail idx, we're sure there's
still available buffers in the virtqueue so there's no need to re-read
avail idx. So let's skip this to avoid unnecessary userspace memory
access and memory barrier. Pktgen test show about 3% improvement on rx
pps.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch makes tap a separate module for other types of virtual interfaces, for example,
ipvlan to use.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming tap related APIs, data structures and macros in tap.c from macvtap_.* to tap_.*
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, under certain circumstances vhost_init_is_le does just a part
of the initialization job, and depends on vhost_reset_is_le being called
too. For this reason vhost_vq_init_access used to call vhost_reset_is_le
when vq->private_data is NULL. This is not only counter intuitive, but
also real a problem because it breaks vhost_net. The bug was introduced to
vhost_net with commit 2751c9882b ("vhost: cross-endian support for
legacy devices"). The symptom is corruption of the vq's used.idx field
(virtio) after VHOST_NET_SET_BACKEND was issued as a part of the vhost
shutdown on a vq with pending descriptors.
Let us make sure the outcome of vhost_init_is_le never depend on the state
it is actually supposed to initialize, and fix virtio_net by removing the
reset from vhost_vq_init_access.
With the above, there is no reason for vhost_reset_is_le to do just half
of the job. Let us make vhost_reset_is_le reinitialize is_le.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reported-by: Michael A. Tebolt <miket@us.ibm.com>
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixes: commit 2751c9882b ("vhost: cross-endian support for legacy devices")
Cc: <stable@vger.kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Michael A. Tebolt <miket@us.ibm.com>
Propagate the error when vhost_vq_init_access() fails and set
vq->private_data to NULL.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is to silence an uninitialized variable warning in debug output.
The problem is this line:
pr_debug("vhost_get_vq_desc: head: %d, out: %u in: %u\n",
head, out, in);
If "head == vq->num" is true on the first iteration then "out" and "in"
aren't initialized. We handle that a few lines after the printk. I was
tempted to just delete the pr_debug() but I decided to just initialize
them to zero instead.
Also checkpatch.pl complains if variables are declared as just
"unsigned" without the "int".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Declare target_core_fabric_ops strucrues as const as they are only
passed as an argument to the functions target_register_template and
target_unregister_template. The arguments are of type const struct
target_core_fabric_ops *, so target_core_fabric_ops structures having
this property can be declared const.
Done using Coccinelle:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct target_core_fabric_ops i@p={...};
@ok@
position p;
identifier r.i;
@@
(
target_register_template(&i@p)
|
target_unregister_template(&i@p)
)
@bad@
position p!={r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
+const
struct target_core_fabric_ops i;
File size before: drivers/vhost/scsi.o
text data bss dec hex filename
18063 2985 40 21088 5260 drivers/vhost/scsi.o
File size after: drivers/vhost/scsi.o
text data bss dec hex filename
18479 2601 40 21120 5280 drivers/vhost/scsi.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
This patch tries to utilize tuntap rx batching by peeking the tx
virtqueue during transmission, if there's more available buffers in
the virtqueue, set MSG_MORE flag for a hint for backend (e.g tuntap)
to batch the packets.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tries to do several tweaks on vhost_vq_avail_empty() for a
better performance:
- check cached avail index first which could avoid userspace memory access.
- using unlikely() for the failure of userspace access
- check vq->last_avail_idx instead of cached avail index as the last
step.
This patch is need for batching supports which needs to peek whether
or not there's still available buffers in the ring.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs updates from Al Viro:
- more ->d_init() stuff (work.dcache)
- pathname resolution cleanups (work.namei)
- a few missing iov_iter primitives - copy_from_iter_full() and
friends. Either copy the full requested amount, advance the iterator
and return true, or fail, return false and do _not_ advance the
iterator. Quite a few open-coded callers converted (and became more
readable and harder to fuck up that way) (work.iov_iter)
- several assorted patches, the big one being logfs removal
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
logfs: remove from tree
vfs: fix put_compat_statfs64() does not handle errors
namei: fold should_follow_link() with the step into not-followed link
namei: pass both WALK_GET and WALK_MORE to should_follow_link()
namei: invert WALK_PUT logics
namei: shift interpretation of LOOKUP_FOLLOW inside should_follow_link()
namei: saner calling conventions for mountpoint_last()
namei.c: get rid of user_path_parent()
switch getfrag callbacks to ..._full() primitives
make skb_add_data,{_nocache}() and skb_copy_to_page_nocache() advance only on success
[iov_iter] new primitives - copy_from_iter_full() and friends
don't open-code file_inode()
ceph: switch to use of ->d_init()
ceph: unify dentry_operations instances
lustre: switch to use of ->d_init()
Remove the unused but set variable se_tpg in vhost_scsi_nexus_cb() to
fix the following GCC warning when building with 'W=1':
drivers/vhost/scsi.c:1752:26: warning: variable ‘se_tpg’ set but not used
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Despite living under drivers/ vringh.c is also used as part of the userspace
virtio tools. Before we can kill off the ACCESS_ONCE()definition in the tools,
we must convert vringh.c to use {READ,WRITE}_ONCE().
This patch does so, along with the required include of <linux/compiler.h> for
the relevant definitions. The userspace tools provide their own definitions in
their own <linux/compiler.h>.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
When event index was enabled, we need to fetch used event from
userspace memory each time. This userspace fetch (with memory
barrier) could be saved sometime when 1) caching used event and 2)
if used event is ahead of new and old to new updating does not cross
it, we're sure there's no need to notify guest.
This will be useful for heavy tx load e.g guest pktgen test with Linux
driver shows ~3.5% improvement.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Multi vsocks may setup the same cid at the same time.
Signed-off-by: Gao feng <omarapazanadi@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Several vhost functions were missing __user annotations
on pointers, causing sparse warnings. Fix this up.
sparse also warns about vhost_process_iotlb_msg which
is local and should be static. Fix that up as well.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost_umem_interval_tree is only used locally within vhost.c, mark it
static. As some functions generated go unused, this triggers warnings
unless we also mark it inline.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pull locking updates from Ingo Molnar:
"The tree got pretty big in this development cycle, but the net effect
is pretty good:
115 files changed, 673 insertions(+), 1522 deletions(-)
The main changes were:
- Rework and generalize the mutex code to remove per arch mutex
primitives. (Peter Zijlstra)
- Add vCPU preemption support: add an interface to query the
preemption status of vCPUs and use it in locking primitives - this
optimizes paravirt performance. (Pan Xinhui, Juergen Gross,
Christian Borntraeger)
- Introduce cpu_relax_yield() and remov cpu_relax_lowlatency() to
clean up and improve the s390 lock yielding machinery and its core
kernel impact. (Christian Borntraeger)
- Micro-optimize mutexes some more. (Waiman Long)
- Reluctantly add the to-be-deprecated mutex_trylock_recursive()
interface on a temporary basis, to give the DRM code more time to
get rid of its locking hacks. Any other users will be NAK-ed on
sight. (We turned off the deprecation warning for the time being to
not pollute the build log.) (Peter Zijlstra)
- Improve the rtmutex code a bit, in light of recent long lived
bugs/races. (Thomas Gleixner)
- Misc fixes, cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/paravirt: Fix bool return type for PVOP_CALL()
x86/paravirt: Fix native_patch()
locking/ww_mutex: Use relaxed atomics
locking/rtmutex: Explain locking rules for rt_mutex_proxy_unlock()/init_proxy_locked()
locking/rtmutex: Get rid of RT_MUTEX_OWNER_MASKALL
x86/paravirt: Optimize native pv_lock_ops.vcpu_is_preempted()
locking/mutex: Break out of expensive busy-loop on {mutex,rwsem}_spin_on_owner() when owner vCPU is preempted
locking/osq: Break out of spin-wait busy waiting loop for a preempted vCPU in osq_lock()
Documentation/virtual/kvm: Support the vCPU preemption check
x86/xen: Support the vCPU preemption check
x86/kvm: Support the vCPU preemption check
x86/kvm: Support the vCPU preemption check
kvm: Introduce kvm_write_guest_offset_cached()
locking/core, x86/paravirt: Implement vcpu_is_preempted(cpu) for KVM and Xen guests
locking/spinlocks, s390: Implement vcpu_is_preempted(cpu)
locking/core, powerpc: Implement vcpu_is_preempted(cpu)
sched/core: Introduce the vcpu_is_preempted(cpu) interface
sched/wake_q: Rename WAKE_Q to DEFINE_WAKE_Q
locking/core: Provide common cpu_relax_yield() definition
locking/mutex: Don't mark mutex_trylock_recursive() as deprecated, temporarily
...
local_addr.svm_cid is host cid. We should check guest cid instead,
which is remote_addr.svm_cid. Otherwise we end up resetting all
connections to all guests.
Cc: stable@vger.kernel.org [4.8+]
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
test_and_set_bit() already implies a memory barrier.
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_from_iter_full(), copy_from_iter_full_nocache() and
csum_and_copy_from_iter_full() - counterparts of copy_from_iter()
et.al., advancing iterator only in case of successful full copy
and returning whether it had been successful or not.
Convert some obvious users. *NOTE* - do not blindly assume that
something is a good candidate for those unless you are sure that
not advancing iov_iter in failure case is the right thing in
this case. Anything that does short read/short write kind of
stuff (or is in a loop, etc.) is unlikely to be a good one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
With the s390 special case of a yielding cpu_relax() implementation gone,
we can now remove all users of cpu_relax_lowlatency() and replace them
with cpu_relax().
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1477386195-32736-5-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Many modules call misc_register and misc_deregister in its module init
and exit methods without any additional code. This ends up being
boilerplate. This patch adds helper macro module_misc_device(), that
replaces module_init()/ module_exit() with template functions.
This patch also converts drivers to use new macro.
Change since v1:
Add device.h include in miscdevice.h as module_driver macro was not
available from other include files in some architectures.
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The address of the iovec &vq->iov[out] is not guaranteed to contain the scsi
command's response iovec throughout the lifetime of the command. Rather, it
is more likely to contain an iovec from an immediately following command
after looping back around to vhost_get_vq_desc(). Pass along the iovec
entirely instead.
Fixes: 79c14141a4 ("vhost/scsi: Convert completion path to use copy_to_iter")
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Stash the packet length in a local variable before handing over
ownership of the packet to virtio_transport_recv_pkt() or
virtio_transport_free_pkt().
This patch solves the use-after-free since pkt is no longer guaranteed
to be alive.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
- New vsock device support in host and guest
- Platform IOMMU support in host and guest,
including compatibility quirks for legacy systems.
- Misc fixes and cleanups.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXofvbAAoJECgfDbjSjVRpUTIH/iEoK9h636tBayXy0PXkPby0
6fMaRFy6H1HgEttgDhJE8Pqg/ba3qaW9Em0fHyFq7Mp2waFHAZ8hAT8phC6TAK3c
CIBnfzyyuI8u3N9SnNOfelPVcwCBfuALuuTsXB/rwKbYQEVv+U5Rdt3Vyx9+lXkj
P005klz7PfqxFhQrrnj4Eh7VawtHwmMuLH8YoWpCZpM71dHPo6eL+3ftKwhH2boo
qK86uVprwba03Pewpm13vQnotemfVfUUkjXd4EJpG3dx7E0KZosuj0ZG9OV8mPGQ
Cl2gBdUhocdJgeUnAHmf6tumYi9KFlYfy6xLy44YMmN7FL3E9nQjaKZp25UKfiM=
=ztIm
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost updates from Michael Tsirkin:
- new vsock device support in host and guest
- platform IOMMU support in host and guest, including compatibility
quirks for legacy systems.
- misc fixes and cleanups.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
VSOCK: Use kvfree()
vhost: split out vringh Kconfig
vhost: detect 32 bit integer wrap around
vhost: new device IOTLB API
vhost: drop vringh dependency
vhost: convert pre sorted vhost memory array to interval tree
vhost: introduce vhost memory accessors
VSOCK: Add Makefile and Kconfig
VSOCK: Introduce vhost_vsock.ko
VSOCK: Introduce virtio_transport.ko
VSOCK: Introduce virtio_vsock_common.ko
VSOCK: defer sock removal to transports
VSOCK: transport-specific vsock_transport functions
vhost: drop vringh dependency
vop: pull in vhost Kconfig
virtio: new feature to detect IOMMU device quirk
balloon: check the number of available pages in leak balloon
vhost: lockless enqueuing
vhost: simplify work flushing
vringh is pulled in by caif and mic, but the other
vhost config does not need to be there.
In particular, it makes no sense to have vhost net/scsi/sock
under caif/mic.
Create a separate Kconfig file and put vringh bits there.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch tries to implement an device IOTLB for vhost. This could be
used with userspace(qemu) implementation of DMA remapping
to emulate an IOMMU for the guest.
The idea is simple, cache the translation in a software device IOTLB
(which is implemented as an interval tree) in vhost and use vhost_net
file descriptor for reporting IOTLB miss and IOTLB
update/invalidation. When vhost meets an IOTLB miss, the fault
address, size and access can be read from the file. After userspace
finishes the translation, it writes the translated address to the
vhost_net file to update the device IOTLB.
When device IOTLB is enabled by setting VIRTIO_F_IOMMU_PLATFORM all vq
addresses set by ioctl are treated as iova instead of virtual address and
the accessing can only be done through IOTLB instead of direct userspace
memory access. Before each round or vq processing, all vq metadata is
prefetched in device IOTLB to make sure no translation fault happens
during vq processing.
In most cases, virtqueues are contiguous even in virtual address space.
The IOTLB translation for virtqueue itself may make it a little
slower. We might add fast path cache on top of this patch.
Signed-off-by: Jason Wang <jasowang@redhat.com>
[mst: use virtio feature bit: VHOST_F_DEVICE_IOTLB -> VIRTIO_F_IOMMU_PLATFORM ]
[mst: fix build warnings ]
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[ weiyj.lk: missing unlock on error ]
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Current pre-sorted memory region array has some limitations for future
device IOTLB conversion:
1) need extra work for adding and removing a single region, and it's
expected to be slow because of sorting or memory re-allocation.
2) need extra work of removing a large range which may intersect
several regions with different size.
3) need trick for a replacement policy like LRU
To overcome the above shortcomings, this patch convert it to interval
tree which can easily address the above issue with almost no extra
work.
The patch could be used for:
- Extend the current API and only let the userspace to send diffs of
memory table.
- Simplify Device IOTLB implementation.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces vhost memory accessors which were just wrappers
for userspace address access helpers. This is a requirement for vhost
device iotlb implementation which will add iotlb translations in those
accessors.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Enable virtio-vsock and vhost-vsock.
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VM sockets vhost transport implementation. This driver runs on the
host.
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We use spinlock to synchronize the work list now which may cause
unnecessary contentions. So this patch switch to use llist to remove
this contention. Pktgen tests shows about 5% improvement:
Before:
~1300000 pps
After:
~1370000 pps
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We used to implement the work flushing through tracking queued seq,
done seq, and the number of flushing. This patch simplify this by just
implement work flushing through another kind of vhost work with
completion. This will be used by lockless enqueuing patch.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We used to queue tx packets in sk_receive_queue, this is less
efficient since it requires spinlocks to synchronize between producer
and consumer.
This patch tries to address this by:
- switch from sk_receive_queue to a skb_array, and resize it when
tx_queue_len was changed.
- introduce a new proto_ops peek_len which was used for peeking the
skb length.
- implement a tun version of peek_len for vhost_net to use and convert
vhost_net to use peek_len if possible.
Pktgen test shows about 15.3% improvement on guest receiving pps for small
buffers:
Before: ~1300000pps
After : ~1500000pps
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't stop rx polling socket during rx processing, this will lead
unnecessary wakeups from under layer net devices (E.g
sock_def_readable() form tun). Rx will be slowed down in this
way. This patch avoids this by stop polling socket during rx
processing. A small drawback is that this introduces some overheads in
light load case because of the extra start/stop polling, but single
netperf TCP_RR does not notice any change. In a super heavy load case,
e.g using pktgen to inject packet to guest, we get about ~8.8%
improvement on pps:
before: ~1240000 pkt/s
after: ~1350000 pkt/s
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turns out the template and thus many drivers got the return value wrong:
0 means the fabrics driver needs to put a session reference, which no
driver except for the iSCSI target drivers did. Fortunately none of these
drivers supports explicit Node ACLs, so the bug was harmless.
Even without that only qla2xxx and iscsi every did real work in
shutdown_session, so get rid of the boilerplate code in all other
drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add target_alloc_session() w/ callback helper for doing se_session
allocation + tag + se_node_acl lookup. (HCH + nab)
- Tree-wide fabric driver conversion to use target_alloc_session()
- Convert sbp-target to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Chris Boot + nab)
- Convert usb-gadget to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Andrzej Pietrasiewicz + nab)
- Convert xen-scsiback to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Juergen Gross + nab)
- Convert tcm_fc to use TARGET_SCF_ACK_KREF I/O + TMR krefs
- Convert ib_srpt to use percpu_ida tag pre-allocation
- Add DebugFS node for qla2xxx target sess list (Quinn)
- Rework iser-target connection termination (Jenny + Sagi)
- Convert iser-target to new CQ API (HCH)
- Add pass-through WRITE_SAME support for IBLOCK (Mike Christie)
- Introduce data_bitmap for asynchronous access of data area (Sheng
Yang + Andy)
- Fix target_release_cmd_kref shutdown comp leak (Himanshu Madhani)
Also, there is a separate PULL request coming for cxgb4 NIC driver
prerequisites for supporting hw iscsi segmentation offload (ISO), that
will be the base for a number of v4.7 developments involving
iscsi-target hw offloads"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits)
target: Fix target_release_cmd_kref shutdown comp leak
target: Avoid DataIN transfers for non-GOOD SAM status
target/user: Report capability of handling out-of-order completions to userspace
target/user: Fix size_t format-spec build warning
target/user: Don't free expired command when time out
target/user: Introduce data_bitmap, replace data_length/data_head/data_tail
target/user: Free data ring in unified function
target/user: Use iovec[] to describe continuous area
target: Remove enum transport_lunflags_table
target/iblock: pass WRITE_SAME to device if possible
iser-target: Kill the ->isert_cmd back pointer in struct iser_tx_desc
iser-target: Kill struct isert_rdma_wr
iser-target: Convert to new CQ API
iser-target: Split and properly type the login buffer
iser-target: Remove ISER_RECV_DATA_SEG_LEN
iser-target: Remove impossible condition from isert_wait_conn
iser-target: Remove redundant wait in release_conn
iser-target: Rework connection termination
iser-target: Separate flows for np listeners and connections cma events
iser-target: Add new state ISER_CONN_BOUND to isert_conn
...
Linus Torvalds