After commit 07f4c90062 ("tcp/dccp: try to not exhaust
ip_local_port_range in connect()") it is advised to have an even number
of ports described in /proc/sys/net/ipv4/ip_local_port_range
This means start/end values should have a different parity.
Let's warn sysadmins of this, so that they can update their settings
if they want to.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By making sure sk->sk_gso_max_segs minimal value is one,
and sysctl_tcp_min_tso_segs minimal value is one as well,
tcp_tso_autosize() will return a non zero value.
We can then revert 843925f33f
("tcp: Do not apply TSO segment limit to non-TSO packets")
and save few cpu cycles in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work as a follow-up of commit f7b3bec6f5 ("net: allow setting ecn
via routing table") and adds RFC3168 section 6.1.1.1. fallback for outgoing
ECN connections. In other words, this work adds a retry with a non-ECN
setup SYN packet, as suggested from the RFC on the first timeout:
[...] A host that receives no reply to an ECN-setup SYN within the
normal SYN retransmission timeout interval MAY resend the SYN and
any subsequent SYN retransmissions with CWR and ECE cleared. [...]
Schematic client-side view when assuming the server is in tcp_ecn=2 mode,
that is, Linux default since 2009 via commit 255cac91c3 ("tcp: extend
ECN sysctl to allow server-side only ECN"):
1) Normal ECN-capable path:
SYN ECE CWR ----->
<----- SYN ACK ECE
ACK ----->
2) Path with broken middlebox, when client has fallback:
SYN ECE CWR ----X crappy middlebox drops packet
(timeout, rtx)
SYN ----->
<----- SYN ACK
ACK ----->
In case we would not have the fallback implemented, the middlebox drop
point would basically end up as:
SYN ECE CWR ----X crappy middlebox drops packet
(timeout, rtx)
SYN ECE CWR ----X crappy middlebox drops packet
(timeout, rtx)
SYN ECE CWR ----X crappy middlebox drops packet
(timeout, rtx)
In any case, it's rather a smaller percentage of sites where there would
occur such additional setup latency: it was found in end of 2014 that ~56%
of IPv4 and 65% of IPv6 servers of Alexa 1 million list would negotiate
ECN (aka tcp_ecn=2 default), 0.42% of these webservers will fail to connect
when trying to negotiate with ECN (tcp_ecn=1) due to timeouts, which the
fallback would mitigate with a slight latency trade-off. Recent related
paper on this topic:
Brian Trammell, Mirja Kühlewind, Damiano Boppart, Iain Learmonth,
Gorry Fairhurst, and Richard Scheffenegger:
"Enabling Internet-Wide Deployment of Explicit Congestion Notification."
Proc. PAM 2015, New York.
http://ecn.ethz.ch/ecn-pam15.pdf
Thus, when net.ipv4.tcp_ecn=1 is being set, the patch will perform RFC3168,
section 6.1.1.1. fallback on timeout. For users explicitly not wanting this
which can be in DC use case, we add a net.ipv4.tcp_ecn_fallback knob that
allows for disabling the fallback.
tp->ecn_flags are not being cleared in tcp_ecn_clear_syn() on output, but
rather we let tcp_ecn_rcv_synack() take that over on input path in case a
SYN ACK ECE was delayed. Thus a spurious SYN retransmission will not prevent
ECN being negotiated eventually in that case.
Reference: https://www.ietf.org/proceedings/92/slides/slides-92-iccrg-1.pdf
Reference: https://www.ietf.org/proceedings/89/slides/slides-89-tsvarea-1.pdf
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mirja Kühlewind <mirja.kuehlewind@tik.ee.ethz.ch>
Signed-off-by: Brian Trammell <trammell@tik.ee.ethz.ch>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Dave That <dave.taht@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 code uses a mixture of coding styles. In some instances check
for NULL pointer is done as x == NULL and sometimes as !x. !x is
preferred according to checkpatch and this patch makes the code
consistent by adopting the latter form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per RFC4821 7.3. Selecting Probe Size, a probe timer should
be armed once probing has converged. Once this timer expired,
probing again to take advantage of any path PMTU change. The
recommended probing interval is 10 minutes per RFC1981. Probing
interval could be sysctled by sysctl_tcp_probe_interval.
Eric Dumazet suggested to implement pseudo timer based on 32bits
jiffies tcp_time_stamp instead of using classic timer for such
rare event.
Signed-off-by: Fan Du <fan.du@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current probe_size is chosen by doubling mss_cache,
the probing process will end shortly with a sub-optimal
mss size, and the link mtu will not be taken full
advantage of, in return, this will make user to tweak
tcp_base_mss with care.
Use binary search to choose probe_size in a fine
granularity manner, an optimal mss will be found
to boost performance as its maxmium.
In addition, introduce a sysctl_tcp_probe_threshold
to control when probing will stop in respect to
the width of search range.
Test env:
Docker instance with vxlan encapuslation(82599EB)
iperf -c 10.0.0.24 -t 60
before this patch:
1.26 Gbits/sec
After this patch: increase 26%
1.59 Gbits/sec
Signed-off-by: Fan Du <fan.du@intel.com>
Acked-by: John Heffner <johnwheffner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packetization Layer Path MTU Discovery works separately beside
Path MTU Discovery at IP level, different net namespace has
various requirements on which one to chose, e.g., a virutalized
container instance would require TCP PMTU to probe an usable
effective mtu for underlying tunnel, while the host would
employ classical ICMP based PMTU to function.
Hence making TCP PMTU mechanism per net namespace to decouple
two functionality. Furthermore the probe base MSS should also
be configured separately for each namespace.
Signed-off-by: Fan Du <fan.du@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Helpers for mitigating ACK loops by rate-limiting dupacks sent in
response to incoming out-of-window packets.
This patch includes:
- rate-limiting logic
- sysctl to control how often we allow dupacks to out-of-window packets
- SNMP counter for cases where we rate-limited our dupack sending
The rate-limiting logic in this patch decides to not send dupacks in
response to out-of-window segments if (a) they are SYNs or pure ACKs
and (b) the remote endpoint is sending them faster than the configured
rate limit.
We rate-limit our responses rather than blocking them entirely or
resetting the connection, because legitimate connections can rely on
dupacks in response to some out-of-window segments. For example, zero
window probes are typically sent with a sequence number that is below
the current window, and ZWPs thus expect to thus elicit a dupack in
response.
We allow dupacks in response to TCP segments with data, because these
may be spurious retransmissions for which the remote endpoint wants to
receive DSACKs. This is safe because segments with data can't
realistically be part of ACK loops, which by their nature consist of
each side sending pure/data-less ACKs to each other.
The dupack interval is controlled by a new sysctl knob,
tcp_invalid_ratelimit, given in milliseconds, in case an administrator
needs to dial this upward in the face of a high-rate DoS attack. The
name and units are chosen to be analogous to the existing analogous
knob for ICMP, icmp_ratelimit.
The default value for tcp_invalid_ratelimit is 500ms, which allows at
most one such dupack per 500ms. This is chosen to be 2x faster than
the 1-second minimum RTO interval allowed by RFC 6298 (section 2, rule
2.4). We allow the extra 2x factor because network delay variations
can cause packets sent at 1 second intervals to be compressed and
arrive much closer.
Reported-by: Avery Fay <avery@mixpanel.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing upcoming Yaogong patch (converting out of order queue
into an RB tree), I hit the max reordering level of linux TCP stack.
Reordering level was limited to 127 for no good reason, and some
network setups [1] can easily reach this limit and get limited
throughput.
Allow a new max limit of 300, and add a sysctl to allow admins to even
allow bigger (or lower) values if needed.
[1] Aggregation of links, per packet load balancing, fabrics not doing
deep packet inspections, alternative TCP congestion modules...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yaogong Wang <wygivan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
1/ Step down as dmaengine maintainer see commit 08223d80df "dmaengine
maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13 (commit
7787380336 "net_dma: mark broken"), without reports of performance
regression.
3/ Miscellaneous fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BBBv
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine updates from Dan Williams:
"Even though this has fixes marked for -stable, given the size and the
needed conflict resolutions this is 3.18-rc1/merge-window material.
These patches have been languishing in my tree for a long while. The
fact that I do not have the time to do proper/prompt maintenance of
this tree is a primary factor in the decision to step down as
dmaengine maintainer. That and the fact that the bulk of drivers/dma/
activity is going through Vinod these days.
The net_dma removal has not been in -next. It has developed simple
conflicts against mainline and net-next (for-3.18).
Continuing thanks to Vinod for staying on top of drivers/dma/.
Summary:
1/ Step down as dmaengine maintainer see commit 08223d80df
"dmaengine maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13
(commit 7787380336 "net_dma: mark broken"), without reports of
performance regression.
3/ Miscellaneous fixes"
* tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
net: make tcp_cleanup_rbuf private
net_dma: revert 'copied_early'
net_dma: simple removal
dmaengine maintainer update
dmatest: prevent memory leakage on error path in thread
ioat: Use time_before_jiffies()
dmaengine: fix xor sources continuation
dma: mv_xor: Rename __mv_xor_slot_cleanup() to mv_xor_slot_cleanup()
dma: mv_xor: Remove all callers of mv_xor_slot_cleanup()
dma: mv_xor: Remove unneeded mv_xor_clean_completed_slots() call
ioat: Use pci_enable_msix_exact() instead of pci_enable_msix()
drivers: dma: Include appropriate header file in dca.c
drivers: dma: Mark functions as static in dma_v3.c
dma: mv_xor: Add DMA API error checks
ioat/dca: Use dev_is_pci() to check whether it is pci device
Per commit "77873803363c net_dma: mark broken" net_dma is no longer used
and there is no plan to fix it.
This is the mechanical removal of bits in CONFIG_NET_DMA ifdef guards.
Reverting the remainder of the net_dma induced changes is deferred to
subsequent patches.
Marked for stable due to Roman's report of a memory leak in
dma_pin_iovec_pages():
https://lkml.org/lkml/2014/9/3/177
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: David Whipple <whipple@securedatainnovations.ch>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: <stable@vger.kernel.org>
Reported-by: Roman Gushchin <klamm@yandex-team.ru>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Current ICMP rate limiting uses inetpeer cache, which is an RBL tree
protected by a lock, meaning that hosts can be stuck hard if all cpus
want to check ICMP limits.
When say a DNS or NTP server process is restarted, inetpeer tree grows
quick and machine comes to its knees.
iptables can not help because the bottleneck happens before ICMP
messages are even cooked and sent.
This patch adds a new global limitation, using a token bucket filter,
controlled by two new sysctl :
icmp_msgs_per_sec - INTEGER
Limit maximal number of ICMP packets sent per second from this host.
Only messages whose type matches icmp_ratemask are
controlled by this limit.
Default: 1000
icmp_msgs_burst - INTEGER
icmp_msgs_per_sec controls number of ICMP packets sent per second,
while icmp_msgs_burst controls the burst size of these packets.
Default: 50
Note that if we really want to send millions of ICMP messages per
second, we might extend idea and infra added in commit 04ca6973f7
("ip: make IP identifiers less predictable") :
add a token bucket in the ip_idents hash and no longer rely on inetpeer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net.ipv4.ip_nonlocal_bind sysctl was global to all network
namespaces. This patch allows to set a different value for each
network namespace.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
As in IPv6 people might increase the igmp query robustness variable to
make sure unsolicited state change reports aren't lost on the network. Add
and document this new knob to igmp code.
RFCs allow tuning this parameter back to first IGMP RFC, so we also use
this setting for all counters, including source specific multicast.
Also take over sysctl value when upping the interface and don't reuse
the last one seen on the interface.
Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_local_port_range is already per netns, so should ip_local_reserved_ports
be. And since it is none by default we don't actually need it when we don't
enable CONFIG_SYSCTL.
By the way, rename inet_is_reserved_local_port() to inet_is_local_reserved_port()
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using mark-based routing, sockets returned from accept()
may need to be marked differently depending on the incoming
connection request.
This is the case, for example, if different socket marks identify
different networks: a listening socket may want to accept
connections from all networks, but each connection should be
marked with the network that the request came in on, so that
subsequent packets are sent on the correct network.
This patch adds a sysctl to mark TCP sockets based on the fwmark
of the incoming SYN packet. If enabled, and an unmarked socket
receives a SYN, then the SYN packet's fwmark is written to the
connection's inet_request_sock, and later written back to the
accepted socket when the connection is established. If the
socket already has a nonzero mark, then the behaviour is the same
as it is today, i.e., the listening socket's fwmark is used.
Black-box tested using user-mode linux:
- IPv4/IPv6 SYN+ACK, FIN, etc. packets are routed based on the
mark of the incoming SYN packet.
- The socket returned by accept() is marked with the mark of the
incoming SYN packet.
- Tested with syncookies=1 and syncookies=2.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel-originated IP packets that have no user socket associated
with them (e.g., ICMP errors and echo replies, TCP RSTs, etc.)
are emitted with a mark of zero. Add a sysctl to make them have
the same mark as the packet they are replying to.
This allows an administrator that wishes to do so to use
mark-based routing, firewalling, etc. for these replies by
marking the original packets inbound.
Tested using user-mode linux:
- ICMP/ICMPv6 echo replies and errors.
- TCP RST packets (IPv4 and IPv6).
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly, when CONFIG_SYSCTL is not set, ping_group_range should still
work, just that no one can change it. Therefore we should move it out of
sysctl_net_ipv4.c. And, it should not share the same seqlock with
ip_local_port_range.
BTW, rename it to ->ping_group_range instead.
Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_SYSCTL is not set, ip_local_port_range should still work,
just that no one can change it. Therefore we should move it out of sysctl_inet.c.
Also, rename it to ->ip_local_ports instead.
Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While forwarding we should not use the protocol path mtu to calculate
the mtu for a forwarded packet but instead use the interface mtu.
We mark forwarded skbs in ip_forward with IPSKB_FORWARDED, which was
introduced for multicast forwarding. But as it does not conflict with
our usage in unicast code path it is perfect for reuse.
I moved the functions ip_sk_accept_pmtu, ip_sk_use_pmtu and ip_skb_dst_mtu
along with the new ip_dst_mtu_maybe_forward to net/ip.h to fix circular
dependencies because of IPSKB_FORWARDED.
Because someone might have written a software which does probe
destinations manually and expects the kernel to honour those path mtus
I introduced a new per-namespace "ip_forward_use_pmtu" knob so someone
can disable this new behaviour. We also still use mtus which are locked on a
route for forwarding.
The reason for this change is, that path mtus information can be injected
into the kernel via e.g. icmp_err protocol handler without verification
of local sockets. As such, this could cause the IPv4 forwarding path to
wrongfully emit fragmentation needed notifications or start to fragment
packets along a path.
Tunnel and ipsec output paths clear IPCB again, thus IPSKB_FORWARDED
won't be set and further fragmentation logic will use the path mtu to
determine the fragmentation size. They also recheck packet size with
help of path mtu discovery and report appropriate errors.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The other field in ipv4_config, log_martians, was converted to a
per-interface setting, so we can just remove the whole structure.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of TCP Small Queues, TSO auto sizing, and TCP
pacing, we can implement Automatic Corking in the kernel, to help
applications doing small write()/sendmsg() to TCP sockets.
Idea is to change tcp_push() to check if the current skb payload is
under skb optimal size (a multiple of MSS bytes)
If under 'size_goal', and at least one packet is still in Qdisc or
NIC TX queues, set the TCP Small Queue Throttled bit, so that the push
will be delayed up to TX completion time.
This delay might allow the application to coalesce more bytes
in the skb in following write()/sendmsg()/sendfile() system calls.
The exact duration of the delay is depending on the dynamics
of the system, and might be zero if no packet for this flow
is actually held in Qdisc or NIC TX ring.
Using FQ/pacing is a way to increase the probability of
autocorking being triggered.
Add a new sysctl (/proc/sys/net/ipv4/tcp_autocorking) to control
this feature and default it to 1 (enabled)
Add a new SNMP counter : nstat -a | grep TcpExtTCPAutoCorking
This counter is incremented every time we detected skb was under used
and its flush was deferred.
Tested:
Interesting effects when using line buffered commands under ssh.
Excellent performance results in term of cpu usage and total throughput.
lpq83:~# echo 1 >/proc/sys/net/ipv4/tcp_autocorking
lpq83:~# perf stat ./super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128
9410.39
Performance counter stats for './super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128':
35209.439626 task-clock # 2.901 CPUs utilized
2,294 context-switches # 0.065 K/sec
101 CPU-migrations # 0.003 K/sec
4,079 page-faults # 0.116 K/sec
97,923,241,298 cycles # 2.781 GHz [83.31%]
51,832,908,236 stalled-cycles-frontend # 52.93% frontend cycles idle [83.30%]
25,697,986,603 stalled-cycles-backend # 26.24% backend cycles idle [66.70%]
102,225,978,536 instructions # 1.04 insns per cycle
# 0.51 stalled cycles per insn [83.38%]
18,657,696,819 branches # 529.906 M/sec [83.29%]
91,679,646 branch-misses # 0.49% of all branches [83.40%]
12.136204899 seconds time elapsed
lpq83:~# echo 0 >/proc/sys/net/ipv4/tcp_autocorking
lpq83:~# perf stat ./super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128
6624.89
Performance counter stats for './super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128':
40045.864494 task-clock # 3.301 CPUs utilized
171 context-switches # 0.004 K/sec
53 CPU-migrations # 0.001 K/sec
4,080 page-faults # 0.102 K/sec
111,340,458,645 cycles # 2.780 GHz [83.34%]
61,778,039,277 stalled-cycles-frontend # 55.49% frontend cycles idle [83.31%]
29,295,522,759 stalled-cycles-backend # 26.31% backend cycles idle [66.67%]
108,654,349,355 instructions # 0.98 insns per cycle
# 0.57 stalled cycles per insn [83.34%]
19,552,170,748 branches # 488.244 M/sec [83.34%]
157,875,417 branch-misses # 0.81% of all branches [83.34%]
12.130267788 seconds time elapsed
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slow start now increases cwnd by 1 if an ACK acknowledges some packets,
regardless the number of packets. Consequently slow start performance
is highly dependent on the degree of the stretch ACKs caused by
receiver or network ACK compression mechanisms (e.g., delayed-ACK,
GRO, etc). But slow start algorithm is to send twice the amount of
packets of packets left so it should process a stretch ACK of degree
N as if N ACKs of degree 1, then exits when cwnd exceeds ssthresh. A
follow up patch will use the remainder of the N (if greater than 1)
to adjust cwnd in the congestion avoidance phase.
In addition this patch retires the experimental limited slow start
(LSS) feature. LSS has multiple drawbacks but questionable benefit. The
fractional cwnd increase in LSS requires a loop in slow start even
though it's rarely used. Configuring such an increase step via a global
sysctl on different BDPS seems hard. Finally and most importantly the
slow start overshoot concern is now better covered by the Hybrid slow
start (hystart) enabled by default.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow unprivileged users to use:
/proc/sys/net/ipv4/icmp_echo_ignore_all
/proc/sys/net/ipv4/icmp_echo_ignore_broadcasts
/proc/sys/net/ipv4/icmp_ignore_bogus_error_response
/proc/sys/net/ipv4/icmp_errors_use_inbound_ifaddr
/proc/sys/net/ipv4/icmp_ratelimit
/proc/sys/net/ipv4/icmp_ratemask
/proc/sys/net/ipv4/ping_group_range
/proc/sys/net/ipv4/tcp_ecn
/proc/sys/net/ipv4/ip_local_ports_range
These are occassionally handy and after a quick review I don't see
any problems with unprivileged users using them.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify maintenance of ipv4_net_table by using math to point the per
net sysctls into the appropriate struct net, instead of manually
reassinging all of the variables into hard coded table slots.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that is implemented is per memory cgroup not per netns, and
having per netns bits is just confusing. Remove the per netns bits to
make it easier to see what is really going on.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is broken and does not constrain sysctl_tcp_mem as
tcp_update_limit does. With the result that it allows the cgroup tcp
memory limits to be bypassed.
The semantics are broken as the settings are not per netns and are in a
per netns table, and instead looks at current.
Since the code is broken in both design and implementation and does not
implement the functionality for which it was written remove it.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed key initialization of tcp_fastopen cookies to net_get_random_once.
If the user sets a custom key net_get_random_once must be called at
least once to ensure we don't overwrite the user provided key when the
first cookie is generated later on.
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Move sysctl_local_ports from a global variable into struct netns_ipv4.
- Modify inet_get_local_port_range to take a struct net, and update all
of the callers.
- Move the initialization of sysctl_local_ports into
sysctl_net_ipv4.c:ipv4_sysctl_init_net from inet_connection_sock.c
v2:
- Ensure indentation used tabs
- Fixed ip.h so it applies cleanly to todays net-next
v3:
- Compile fixes of strange callers of inet_get_local_port_range.
This patch now successfully passes an allmodconfig build.
Removed manual inlining of inet_get_local_port_range in ipv4_local_port_range
Originally-by: Samya <samya@twitter.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After hearing many people over past years complaining against TSO being
bursty or even buggy, we are proud to present automatic sizing of TSO
packets.
One part of the problem is that tcp_tso_should_defer() uses an heuristic
relying on upcoming ACKS instead of a timer, but more generally, having
big TSO packets makes little sense for low rates, as it tends to create
micro bursts on the network, and general consensus is to reduce the
buffering amount.
This patch introduces a per socket sk_pacing_rate, that approximates
the current sending rate, and allows us to size the TSO packets so
that we try to send one packet every ms.
This field could be set by other transports.
Patch has no impact for high speed flows, where having large TSO packets
makes sense to reach line rate.
For other flows, this helps better packet scheduling and ACK clocking.
This patch increases performance of TCP flows in lossy environments.
A new sysctl (tcp_min_tso_segs) is added, to specify the
minimal size of a TSO packet (default being 2).
A follow-up patch will provide a new packet scheduler (FQ), using
sk_pacing_rate as an input to perform optional per flow pacing.
This explains why we chose to set sk_pacing_rate to twice the current
rate, allowing 'slow start' ramp up.
sk_pacing_rate = 2 * cwnd * mss / srtt
v2: Neal Cardwell reported a suspect deferring of last two segments on
initial write of 10 MSS, I had to change tcp_tso_should_defer() to take
into account tp->xmit_size_goal_segs
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Van Jacobson <vanj@google.com>
Cc: Tom Herbert <therbert@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Idea of this patch is to add optional limitation of number of
unsent bytes in TCP sockets, to reduce usage of kernel memory.
TCP receiver might announce a big window, and TCP sender autotuning
might allow a large amount of bytes in write queue, but this has little
performance impact if a large part of this buffering is wasted :
Write queue needs to be large only to deal with large BDP, not
necessarily to cope with scheduling delays (incoming ACKS make room
for the application to queue more bytes)
For most workloads, using a value of 128 KB or less is OK to give
applications enough time to react to POLLOUT events in time
(or being awaken in a blocking sendmsg())
This patch adds two ways to set the limit :
1) Per socket option TCP_NOTSENT_LOWAT
2) A sysctl (/proc/sys/net/ipv4/tcp_notsent_lowat) for sockets
not using TCP_NOTSENT_LOWAT socket option (or setting a zero value)
Default value being UINT_MAX (0xFFFFFFFF), meaning this has no effect.
This changes poll()/select()/epoll() to report POLLOUT
only if number of unsent bytes is below tp->nosent_lowat
Note this might increase number of sendmsg()/sendfile() calls
when using non blocking sockets,
and increase number of context switches for blocking sockets.
Note this is not related to SO_SNDLOWAT (as SO_SNDLOWAT is
defined as :
Specify the minimum number of bytes in the buffer until
the socket layer will pass the data to the protocol)
Tested:
netperf sessions, and watching /proc/net/protocols "memory" column for TCP
With 200 concurrent netperf -t TCP_STREAM sessions, amount of kernel memory
used by TCP buffers shrinks by ~55 % (20567 pages instead of 45458)
lpq83:~# echo -1 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# (super_netperf 200 -t TCP_STREAM -H remote -l 90 &); sleep 60 ; grep TCP /proc/net/protocols
TCPv6 1880 2 45458 no 208 yes ipv6 y y y y y y y y y y y y y n y y y y y
TCP 1696 508 45458 no 208 yes kernel y y y y y y y y y y y y y n y y y y y
lpq83:~# echo 131072 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# (super_netperf 200 -t TCP_STREAM -H remote -l 90 &); sleep 60 ; grep TCP /proc/net/protocols
TCPv6 1880 2 20567 no 208 yes ipv6 y y y y y y y y y y y y y n y y y y y
TCP 1696 508 20567 no 208 yes kernel y y y y y y y y y y y y y n y y y y y
Using 128KB has no bad effect on the throughput or cpu usage
of a single flow, although there is an increase of context switches.
A bonus is that we hold socket lock for a shorter amount
of time and should improve latencies of ACK processing.
lpq83:~# echo -1 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# perf stat -e context-switches ./netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3
OMNI Send TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.7.84 () port 0 AF_INET : +/-2.500% @ 99% conf.
Local Remote Local Elapsed Throughput Throughput Local Local Remote Remote Local Remote Service
Send Socket Recv Socket Send Time Units CPU CPU CPU CPU Service Service Demand
Size Size Size (sec) Util Util Util Util Demand Demand Units
Final Final % Method % Method
1651584 6291456 16384 20.00 17447.90 10^6bits/s 3.13 S -1.00 U 0.353 -1.000 usec/KB
Performance counter stats for './netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3':
412,514 context-switches
200.034645535 seconds time elapsed
lpq83:~# echo 131072 >/proc/sys/net/ipv4/tcp_notsent_lowat
lpq83:~# perf stat -e context-switches ./netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3
OMNI Send TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.7.84 () port 0 AF_INET : +/-2.500% @ 99% conf.
Local Remote Local Elapsed Throughput Throughput Local Local Remote Remote Local Remote Service
Send Socket Recv Socket Send Time Units CPU CPU CPU CPU Service Service Demand
Size Size Size (sec) Util Util Util Util Demand Demand Units
Final Final % Method % Method
1593240 6291456 16384 20.00 17321.16 10^6bits/s 3.35 S -1.00 U 0.381 -1.000 usec/KB
Performance counter stats for './netperf -H 7.7.7.84 -t omni -l 20 -c -i10,3':
2,675,818 context-switches
200.029651391 seconds time elapsed
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-By: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit the min/max value passed to the
/proc/sys/net/ipv4/tcp_syn_retries.
Signed-off-by: Michal Tesar <mtesar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the uses of this unnecessary typedef.
Done via perl script:
$ git grep --name-only -w ctl_table net | \
xargs perl -p -i -e '\
sub trim { my ($local) = @_; $local =~ s/(^\s+|\s+$)//g; return $local; } \
s/\b(?<!struct\s)ctl_table\b(\s*\*\s*|\s+\w+)/"struct ctl_table " . trim($1)/ge'
Reflow the modified lines that now exceed 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch series refactor the F-RTO feature (RFC4138/5682).
This is to simplify the loss recovery processing. Existing F-RTO
was developed during the experimental stage (RFC4138) and has
many experimental features. It takes a separate code path from
the traditional timeout processing by overloading CA_Disorder
instead of using CA_Loss state. This complicates CA_Disorder state
handling because it's also used for handling dubious ACKs and undos.
While the algorithm in the RFC does not change the congestion control,
the implementation intercepts congestion control in various places
(e.g., frto_cwnd in tcp_ack()).
The new code implements newer F-RTO RFC5682 using CA_Loss processing
path. F-RTO becomes a small extension in the timeout processing
and interfaces with congestion control and Eifel undo modules.
It lets congestion control (module) determines how many to send
independently. F-RTO only chooses what to send in order to detect
spurious retranmission. If timeout is found spurious it invokes
existing Eifel undo algorithms like DSACK or TCP timestamp based
detection.
The first patch removes all F-RTO code except the sysctl_tcp_frto is
left for the new implementation. Since CA_EVENT_FRTO is removed, TCP
westwood now computes ssthresh on regular timeout CA_EVENT_LOSS event.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCPCT uses option-number 253, reserved for experimental use and should
not be used in production environments.
Further, TCPCT does not fully implement RFC 6013.
As a nice side-effect, removing TCPCT increases TCP's performance for
very short flows:
Doing an apache-benchmark with -c 100 -n 100000, sending HTTP-requests
for files of 1KB size.
before this patch:
average (among 7 runs) of 20845.5 Requests/Second
after:
average (among 7 runs) of 21403.6 Requests/Second
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series implement the Tail loss probe (TLP) algorithm described
in http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01. The
first patch implements the basic algorithm.
TLP's goal is to reduce tail latency of short transactions. It achieves
this by converting retransmission timeouts (RTOs) occuring due
to tail losses (losses at end of transactions) into fast recovery.
TLP transmits one packet in two round-trips when a connection is in
Open state and isn't receiving any ACKs. The transmitted packet, aka
loss probe, can be either new or a retransmission. When there is tail
loss, the ACK from a loss probe triggers FACK/early-retransmit based
fast recovery, thus avoiding a costly RTO. In the absence of loss,
there is no change in the connection state.
PTO stands for probe timeout. It is a timer event indicating
that an ACK is overdue and triggers a loss probe packet. The PTO value
is set to max(2*SRTT, 10ms) and is adjusted to account for delayed
ACK timer when there is only one oustanding packet.
TLP Algorithm
On transmission of new data in Open state:
-> packets_out > 1: schedule PTO in max(2*SRTT, 10ms).
-> packets_out == 1: schedule PTO in max(2*RTT, 1.5*RTT + 200ms)
-> PTO = min(PTO, RTO)
Conditions for scheduling PTO:
-> Connection is in Open state.
-> Connection is either cwnd limited or no new data to send.
-> Number of probes per tail loss episode is limited to one.
-> Connection is SACK enabled.
When PTO fires:
new_segment_exists:
-> transmit new segment.
-> packets_out++. cwnd remains same.
no_new_packet:
-> retransmit the last segment.
Its ACK triggers FACK or early retransmit based recovery.
ACK path:
-> rearm RTO at start of ACK processing.
-> reschedule PTO if need be.
In addition, the patch includes a small variation to the Early Retransmit
(ER) algorithm, such that ER and TLP together can in principle recover any
N-degree of tail loss through fast recovery. TLP is controlled by the same
sysctl as ER, tcp_early_retrans sysctl.
tcp_early_retrans==0; disables TLP and ER.
==1; enables RFC5827 ER.
==2; delayed ER.
==3; TLP and delayed ER. [DEFAULT]
==4; TLP only.
The TLP patch series have been extensively tested on Google Web servers.
It is most effective for short Web trasactions, where it reduced RTOs by 15%
and improved HTTP response time (average by 6%, 99th percentile by 10%).
The transmitted probes account for <0.5% of the overall transmissions.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP Appropriate Byte Count was added by me, but later disabled.
There is no point in maintaining it since it is a potential source
of bugs and Linux already implements other better window protection
heuristics.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found if we write a larger than 4GB value to some sysctl
variables, the sending syscall will hang up forever, because these
variables are 32 bits, such large values make them overflow to 0 or
negative.
This patch try to fix overflow or prevent from zero value setup
of below sysctl variables:
net.core.wmem_default
net.core.rmem_default
net.core.rmem_max
net.core.wmem_max
net.ipv4.udp_rmem_min
net.ipv4.udp_wmem_min
net.ipv4.tcp_wmem
net.ipv4.tcp_rmem
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Li Yu <raise.sail@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per suggestion from Eric Dumazet this patch makes tcp_ecn sysctl
namespace aware. The reason behind this patch is to ease the testing
of ecn problems on the internet and allows applications to tune their
own use of ecn.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting the creation of network namespaces
by unprivileged users, modify all of the per net sysctl exports
and refuse to allow them to unprivileged users.
This makes it safe for unprivileged users in general to access
per net sysctls, and allows sysctls to be exported to unprivileged
users on an individual basis as they are deemed safe.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the rc_dereference of tcp_fastopen_ctx ever fails then we copy 16 bytes
of kernel stack into the proc result.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds all the necessary data structure and support
functions to implement TFO server side. It also documents a number
of flags for the sysctl_tcp_fastopen knob, and adds a few Linux
extension MIBs.
In addition, it includes the following:
1. a new TCP_FASTOPEN socket option an application must call to
supply a max backlog allowed in order to enable TFO on its listener.
2. A number of key data structures:
"fastopen_rsk" in tcp_sock - for a big socket to access its
request_sock for retransmission and ack processing purpose. It is
non-NULL iff 3WHS not completed.
"fastopenq" in request_sock_queue - points to a per Fast Open
listener data structure "fastopen_queue" to keep track of qlen (# of
outstanding Fast Open requests) and max_qlen, among other things.
"listener" in tcp_request_sock - to point to the original listener
for book-keeping purpose, i.e., to maintain qlen against max_qlen
as part of defense against IP spoofing attack.
3. various data structure and functions, many in tcp_fastopen.c, to
support server side Fast Open cookie operations, including
/proc/sys/net/ipv4/tcp_fastopen_key to allow manual rekeying.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Store sysctl_ping_group_range as a paire of kgid_t values
instead of a pair of gid_t values.
- Move the kgid conversion work from ping_init_sock into ipv4_ping_group_range
- For invalid cases reset to the default disabled state.
With the kgid_t conversion made part of the original value sanitation
from userspace understand how the code will react becomes clearer
and it becomes possible to set the sysctl ping group range from
something other than the initial user namespace.
Cc: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Merge Andrew's second set of patches:
- MM
- a few random fixes
- a couple of RTC leftovers
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (120 commits)
rtc/rtc-88pm80x: remove unneed devm_kfree
rtc/rtc-88pm80x: assign ret only when rtc_register_driver fails
mm: hugetlbfs: close race during teardown of hugetlbfs shared page tables
tmpfs: distribute interleave better across nodes
mm: remove redundant initialization
mm: warn if pg_data_t isn't initialized with zero
mips: zero out pg_data_t when it's allocated
memcg: gix memory accounting scalability in shrink_page_list
mm/sparse: remove index_init_lock
mm/sparse: more checks on mem_section number
mm/sparse: optimize sparse_index_alloc
memcg: add mem_cgroup_from_css() helper
memcg: further prevent OOM with too many dirty pages
memcg: prevent OOM with too many dirty pages
mm: mmu_notifier: fix freed page still mapped in secondary MMU
mm: memcg: only check anon swapin page charges for swap cache
mm: memcg: only check swap cache pages for repeated charging
mm: memcg: split swapin charge function into private and public part
mm: memcg: remove needless !mm fixup to init_mm when charging
mm: memcg: remove unneeded shmem charge type
...
After IP route cache removal, rt_cache_rebuild_count is no longer
used.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch impelements the common code for both the client and server.
1. TCP Fast Open option processing. Since Fast Open does not have an
option number assigned by IANA yet, it shares the experiment option
code 254 by implementing draft-ietf-tcpm-experimental-options
with a 16 bits magic number 0xF989. This enables global experiments
without clashing the scarce(2) experimental options available for TCP.
When the draft status becomes standard (maybe), the client should
switch to the new option number assigned while the server supports
both numbers for transistion.
2. The new sysctl tcp_fastopen
3. A place holder init function
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the RFC 5691 mitigation against Blind
Reset attack using RST bit.
Idea is to validate incoming RST sequence,
to match RCV.NXT value, instead of previouly accepted
window : (RCV.NXT <= SEG.SEQ < RCV.NXT+RCV.WND)
If sequence is in window but not an exact match, send
a "challenge ACK", so that the other part can resend an
RST with the appropriate sequence.
Add a new sysctl, tcp_challenge_ack_limit, to limit
number of challenge ACK sent per second.
Add a new SNMP counter to count number of challenge acks sent.
(netstat -s | grep TCPChallengeACK)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kiran Kumar Kella <kkiran@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduce TSQ (TCP Small Queues)
TSQ goal is to reduce number of TCP packets in xmit queues (qdisc &
device queues), to reduce RTT and cwnd bias, part of the bufferbloat
problem.
sk->sk_wmem_alloc not allowed to grow above a given limit,
allowing no more than ~128KB [1] per tcp socket in qdisc/dev layers at a
given time.
TSO packets are sized/capped to half the limit, so that we have two
TSO packets in flight, allowing better bandwidth use.
As a side effect, setting the limit to 40000 automatically reduces the
standard gso max limit (65536) to 40000/2 : It can help to reduce
latencies of high prio packets, having smaller TSO packets.
This means we divert sock_wfree() to a tcp_wfree() handler, to
queue/send following frames when skb_orphan() [2] is called for the
already queued skbs.
Results on my dev machines (tg3/ixgbe nics) are really impressive,
using standard pfifo_fast, and with or without TSO/GSO.
Without reduction of nominal bandwidth, we have reduction of buffering
per bulk sender :
< 1ms on Gbit (instead of 50ms with TSO)
< 8ms on 100Mbit (instead of 132 ms)
I no longer have 4 MBytes backlogged in qdisc by a single netperf
session, and both side socket autotuning no longer use 4 Mbytes.
As skb destructor cannot restart xmit itself ( as qdisc lock might be
taken at this point ), we delegate the work to a tasklet. We use one
tasklest per cpu for performance reasons.
If tasklet finds a socket owned by the user, it sets TSQ_OWNED flag.
This flag is tested in a new protocol method called from release_sock(),
to eventually send new segments.
[1] New /proc/sys/net/ipv4/tcp_limit_output_bytes tunable
[2] skb_orphan() is usually called at TX completion time,
but some drivers call it in their start_xmit() handler.
These drivers should at least use BQL, or else a single TCP
session can still fill the whole NIC TX ring, since TSQ will
have no effect.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Tom Herbert <therbert@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to add a control for disabling early socket demux.
The main motivation behind this patch is to provide an option to disable
the feature as it adds an additional cost to routing that reduces overall
throughput by up to 5%. For example one of my systems went from 12.1Mpps
to 11.6 after the early socket demux was added. It looks like the reason
for the regression is that we are now having to perform two lookups, first
the one for an established socket, and then the one for the routing table.
By adding this patch and toggling the value for ip_early_demux to 0 I am
able to get back to the 12.1Mpps I was previously seeing.
[ Move local variables in ip_rcv_finish() down into the basic
block in which they are actually used. -DaveM ]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements RFC 5827 early retransmit (ER) for TCP.
It reduces DUPACK threshold (dupthresh) if outstanding packets are
less than 4 to recover losses by fast recovery instead of timeout.
While the algorithm is simple, small but frequent network reordering
makes this feature dangerous: the connection repeatedly enter
false recovery and degrade performance. Therefore we implement
a mitigation suggested in the appendix of the RFC that delays
entering fast recovery by a small interval, i.e., RTT/4. Currently
ER is conservative and is disabled for the rest of the connection
after the first reordering event. A large scale web server
experiment on the performance impact of ER is summarized in
section 6 of the paper "Proportional Rate Reduction for TCP”,
IMC 2011. http://conferences.sigcomm.org/imc/2011/docs/p155.pdf
Note that Linux has a similar feature called THIN_DUPACK. The
differences are THIN_DUPACK do not mitigate reorderings and is only
used after slow start. Currently ER is disabled if THIN_DUPACK is
enabled. I would be happy to merge THIN_DUPACK feature with ER if
people think it's a good idea.
ER is enabled by sysctl_tcp_early_retrans:
0: Disables ER
1: Reduce dupthresh to packets_out - 1 when outstanding packets < 4.
2: (Default) reduce dupthresh like mode 1. In addition, delay
entering fast recovery by RTT/4.
Note: mode 2 is implemented in the third part of this patch series.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use struct ctl_path anymore so delete the exported constants.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This results in code with less boiler plate that is a bit easier
to read.
Additionally stops us from using compatibility code in the sysctl
core, hastening the day when the compatibility code can be removed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it clearer which sysctls are relative to your current network
namespace.
This makes it a little less error prone by not exposing sysctls for the
initial network namespace in other namespaces.
This is the same way we handle all of our other network interfaces to
userspace and I can't honestly remember why we didn't do this for
sysctls right from the start.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4acb4190 tries to fix the using uninitialized value
introduced by commit 3dc43e3, but it would make the
per-socket memory limits too small.
This patch fixes this and also remove the redundant codes
introduced in 4acb4190.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Glauber Costa <glommer@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl_tcp_mem() initialization was moved to sysctl_tcp_ipv4.c
in commit 3dc43e3e4d, since it
became a per-ns value.
That code, however, will never run when CONFIG_SYSCTL is
disabled, leading to bogus values on those fields - causing hung
TCP sockets.
This patch fixes it by keeping an initialization code in
tcp_init(). It will be overwritten by the first net namespace
init if CONFIG_SYSCTL is compiled in, and do the right thing if
it is compiled out.
It is also named properly as tcp_init_mem(), to properly signal
its non-sysctl side effect on TCP limits.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: David S. Miller <davem@davemloft.net>
Link: http://lkml.kernel.org/r/4F22D05A.8030604@parallels.com
[ renamed the function, tidied up the changelog a bit ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/sysctl_net_ipv4.c:78:6: warning: symbol 'inet_get_ping_group_range_table'
was not declared. Should it be static?
net/ipv4/sysctl_net_ipv4.c:119:31: warning: incorrect type in argument 2
(different signedness)
net/ipv4/sysctl_net_ipv4.c:119:31: expected int *range
net/ipv4/sysctl_net_ipv4.c:119:31: got unsigned int *<noident>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses the "tcp.limit_in_bytes" field of the kmem_cgroup to
effectively control the amount of kernel memory pinned by a cgroup.
This value is ignored in the root cgroup, and in all others,
caps the value specified by the admin in the net namespaces'
view of tcp_sysctl_mem.
If namespaces are being used, the admin is allowed to set a
value bigger than cgroup's maximum, the same way it is allowed
to set pretty much unlimited values in a real box.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com>
CC: David S. Miller <davem@davemloft.net>
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows each namespace to independently set up
its levels for tcp memory pressure thresholds. This patch
alone does not buy much: we need to make this values
per group of process somehow. This is achieved in the
patches that follows in this patchset.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
CC: David S. Miller <davem@davemloft.net>
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andi Kleen and Tim Chen reported huge contention on inetpeer
unused_peers.lock, on memcached workload on a 40 core machine, with
disabled route cache.
It appears we constantly flip peers refcnt between 0 and 1 values, and
we must insert/remove peers from unused_peers.list, holding a contended
spinlock.
Remove this list completely and perform a garbage collection on-the-fly,
at lookup time, using the expired nodes we met during the tree
traversal.
This removes a lot of code, makes locking more standard, and obsoletes
two sysctls (inet_peer_gc_mintime and inet_peer_gc_maxtime). This also
removes two pointers in inet_peer structure.
There is still a false sharing effect because refcnt is in first cache
line of object [were the links and keys used by lookups are located], we
might move it at the end of inet_peer structure to let this first cache
line mostly read by cpus.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andi Kleen <andi@firstfloor.org>
CC: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_PROC_SYSCTL=n the building process fails:
ping.c:(.text+0x52af3): undefined reference to `inet_get_ping_group_range_net'
Moved inet_get_ping_group_range_net() to ping.c.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPPROTO_ICMP socket kind. It makes it possible to send
ICMP_ECHO messages and receive the corresponding ICMP_ECHOREPLY messages
without any special privileges. In other words, the patch makes it
possible to implement setuid-less and CAP_NET_RAW-less /bin/ping. In
order not to increase the kernel's attack surface, the new functionality
is disabled by default, but is enabled at bootup by supporting Linux
distributions, optionally with restriction to a group or a group range
(see below).
Similar functionality is implemented in Mac OS X:
http://www.manpagez.com/man/4/icmp/
A new ping socket is created with
socket(PF_INET, SOCK_DGRAM, PROT_ICMP)
Message identifiers (octets 4-5 of ICMP header) are interpreted as local
ports. Addresses are stored in struct sockaddr_in. No port numbers are
reserved for privileged processes, port 0 is reserved for API ("let the
kernel pick a free number"). There is no notion of remote ports, remote
port numbers provided by the user (e.g. in connect()) are ignored.
Data sent and received include ICMP headers. This is deliberate to:
1) Avoid the need to transport headers values like sequence numbers by
other means.
2) Make it easier to port existing programs using raw sockets.
ICMP headers given to send() are checked and sanitized. The type must be
ICMP_ECHO and the code must be zero (future extensions might relax this,
see below). The id is set to the number (local port) of the socket, the
checksum is always recomputed.
ICMP reply packets received from the network are demultiplexed according
to their id's, and are returned by recv() without any modifications.
IP header information and ICMP errors of those packets may be obtained
via ancillary data (IP_RECVTTL, IP_RETOPTS, and IP_RECVERR). ICMP source
quenches and redirects are reported as fake errors via the error queue
(IP_RECVERR); the next hop address for redirects is saved to ee_info (in
network order).
socket(2) is restricted to the group range specified in
"/proc/sys/net/ipv4/ping_group_range". It is "1 0" by default, meaning
that nobody (not even root) may create ping sockets. Setting it to "100
100" would grant permissions to the single group (to either make
/sbin/ping g+s and owned by this group or to grant permissions to the
"netadmins" group), "0 4294967295" would enable it for the world, "100
4294967295" would enable it for the users, but not daemons.
The existing code might be (in the unlikely case anyone needs it)
extended rather easily to handle other similar pairs of ICMP messages
(Timestamp/Reply, Information Request/Reply, Address Mask Request/Reply
etc.).
Userspace ping util & patch for it:
http://openwall.info/wiki/people/segoon/ping
For Openwall GNU/*/Linux it was the last step on the road to the
setuid-less distro. A revision of this patch (for RHEL5/OpenVZ kernels)
is in use in Owl-current, such as in the 2011/03/12 LiveCD ISOs:
http://mirrors.kernel.org/openwall/Owl/current/iso/
Initially this functionality was written by Pavel Kankovsky for
Linux 2.4.32, but unfortunately it was never made public.
All ping options (-b, -p, -Q, -R, -s, -t, -T, -M, -I), are tested with
the patch.
PATCH v3:
- switched to flowi4.
- minor changes to be consistent with raw sockets code.
PATCH v2:
- changed ping_debug() to pr_debug().
- removed CONFIG_IP_PING.
- removed ping_seq_fops.owner field (unused for procfs).
- switched to proc_net_fops_create().
- switched to %pK in seq_printf().
PATCH v1:
- fixed checksumming bug.
- CAP_NET_RAW may not create icmp sockets anymore.
RFC v2:
- minor cleanups.
- introduced sysctl'able group range to restrict socket(2).
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
controlling igmp_max_membership is useful even when IP_MULTICAST
is off.
Quagga(an OSPF deamon) uses multicast addresses for all interfaces
using a single socket and hits igmp_max_membership limit when
there are 20 interfaces or more.
Always export sysctl igmp_max_memberships in proc, just like
igmp_max_msf
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always go through a new ip4_dst_hoplimit() helper, just like ipv6.
This allowed several simplifications:
1) The interim dst_metric_hoplimit() can go as it's no longer
userd.
2) The sysctl_ip_default_ttl entry no longer needs to use
ipv4_doint_and_flush, since the sysctl is not cached in
routing cache metrics any longer.
3) ipv4_doint_and_flush no longer needs to be exported and
therefore can be marked static.
When ipv4_doint_and_flush_strategy was removed some time ago,
the external declaration in ip.h was mistakenly left around
so kill that off too.
We have to move the sysctl_ip_default_ttl declaration into
ipv4's route cache definition header net/route.h, because
currently net/ip.h (where the declaration lives now) has
a back dependency on net/route.h
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_win_from_space() does the following:
if (sysctl_tcp_adv_win_scale <= 0)
return space >> (-sysctl_tcp_adv_win_scale);
else
return space - (space >> sysctl_tcp_adv_win_scale);
"space" is int.
As per C99 6.5.7 (3) shifting int for 32 or more bits is
undefined behaviour.
Indeed, if sysctl_tcp_adv_win_scale is exactly 32,
space >> 32 equals space and function returns 0.
Which means we busyloop in tcp_fixup_rcvbuf().
Restrict net.ipv4.tcp_adv_win_scale to [-31, 31].
Fix https://bugzilla.kernel.org/show_bug.cgi?id=20312
Steps to reproduce:
echo 32 >/proc/sys/net/ipv4/tcp_adv_win_scale
wget www.kernel.org
[softlockup]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robin Holt tried to boot a 16TB machine and found some limits were
reached : sysctl_tcp_mem[2], sysctl_udp_mem[2]
We can switch infrastructure to use long "instead" of "int", now
atomic_long_t primitives are available for free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Robin Holt <holt@sgi.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
(Dropped the infiniband part, because Tetsuo modified the related code,
I will send a separate patch for it once this is accepted.)
This patch introduces /proc/sys/net/ipv4/ip_local_reserved_ports which
allows users to reserve ports for third-party applications.
The reserved ports will not be used by automatic port assignments
(e.g. when calling connect() or bind() with port number 0). Explicit
port allocation behavior is unchanged.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This patch enables fast retransmissions after one dupACK for
TCP if the stream is identified as thin. This will reduce
latencies for thin streams that are not able to trigger fast
retransmissions due to high packet interarrival time. This
mechanism is only active if enabled by iocontrol or syscontrol
and the stream is identified as thin.
Signed-off-by: Andreas Petlund <apetlund@simula.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will make TCP use only linear timeouts if the
stream is thin. This will help to avoid the very high latencies
that thin stream suffer because of exponential backoff. This
mechanism is only active if enabled by iocontrol or syscontrol
and the stream is identified as thin. A maximum of 6 linear
timeouts is tried before exponential backoff is resumed.
Signed-off-by: Andreas Petlund <apetlund@simula.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
Define sysctl (tcp_cookie_size) to turn on and off the cookie option
default globally, instead of a compiled configuration option.
Define per socket option (TCP_COOKIE_TRANSACTIONS) for setting constant
data values, retrieving variable cookie values, and other facilities.
Move inline tcp_clear_options() unchanged from net/tcp.h to linux/tcp.h,
near its corresponding struct tcp_options_received (prior to changes).
This is a straightforward re-implementation of an earlier (year-old)
patch that no longer applies cleanly, with permission of the original
author (Adam Langley):
http://thread.gmane.org/gmane.linux.network/102586
These functions will also be used in subsequent patches that implement
additional features.
Requires:
net: TCP_MSS_DEFAULT, TCP_MSS_DESIRED
Signed-off-by: William.Allen.Simpson@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Generated with the following semantic patch
@@
struct net *n1;
struct net *n2;
@@
- n1 == n2
+ net_eq(n1, n2)
@@
struct net *n1;
struct net *n2;
@@
- n1 != n2
+ !net_eq(n1, n2)
applied over {include,net,drivers/net}.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that sys_sysctl is a compatiblity wrapper around /proc/sys
all sysctl strategy routines, and all ctl_name and strategy
entries in the sysctl tables are unused, and can be
revmoed.
In addition neigh_sysctl_register has been modified to no longer
take a strategy argument and it's callers have been modified not
to pass one.
Cc: "David Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
It's unused.
It isn't needed -- read or write flag is already passed and sysctl
shouldn't care about the rest.
It _was_ used in two places at arch/frv for some reason.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.
So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to provide on demand route cache rebuilding. Currently, our
route cache is rebulid periodically regardless of need. This introduced
unneeded periodic latency. This patch offers a better approach. Using code
provided by Eric Dumazet, we compute the standard deviation of the average hash
bucket chain length while running rt_check_expire. Should any given chain
length grow to larger that average plus 4 standard deviations, we trigger an
emergency hash table rebuild for that net namespace. This allows for the common
case in which chains are well behaved and do not grow unevenly to not incur any
latency at all, while those systems (which may be being maliciously attacked),
only rebuild when the attack is detected. This patch take 2 other factors into
account:
1) chains with multiple entries that differ by attributes that do not affect the
hash value are only counted once, so as not to unduly bias system to rebuilding
if features like QOS are heavily used
2) if rebuilding crosses a certain threshold (which is adjustable via the added
sysctl in this patch), route caching is disabled entirely for that net
namespace, since constant rebuilding is less efficient that no caching at all
Tested successfully by me.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
name and nlen parameters passed to ->strategy hook are unused, remove
them. In general ->strategy hook should know what it's doing, and don't
do something tricky for which, say, pointer to original userspace array
may be needed (name).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net> [ networking bits ]
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed sysctl_local_port_range[] and its associated seqlock
sysctl_local_port_range_lock were on separate cache lines.
Moreover, sysctl_local_port_range[] was close to unrelated
variables, highly modified, leading to cache misses.
Moving these two variables in a structure can help data
locality and moving this structure to read_mostly section
helps sharing of this data among cpus.
Cleanup of extern declarations (moved in include file where
they belong), and use of inet_get_local_port_range()
accessor instead of direct access to ports values.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 76e6ebfb40 ("netns: add namespace
parameter to rt_cache_flush") acceses the extra2 parameter of the
ip_default_ttl ctl_table, but it is never set to a meaningful
value. When e84f84f276 ("netns: place
rt_genid into struct net") is applied, we'll oops in
rt_cache_invalidate(). Set extra2 to init_net, to avoid that.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Tested-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Piss-poor sysctl registration API strikes again, film at 11...
What we really need is _pathname_ required to be present in already
registered table, so that kernel could warn about bad order. That's the
next target for sysctl stuff (and generally saner and more explicit
order of initialization of ipv[46] internals wouldn't hurt either).
For the time being, here are full fixups required by ..._rotable()
stuff; we make per-net sysctl sets descendents of "ro" one and make sure
that sufficient skeleton is there before we start registering per-net
sysctls.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Massage ipv4 initialization - make sure that net.ipv4 appears as
non-per-net-namespace before it shows up in per-net-namespace sysctls.
That's the only change outside of sysctl.c needed to get sane ordering
rules and data structures for sysctls (esp. for procfs side of that
mess).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Convert the sysctl values for icmp ratelimit to use milliseconds instead
of jiffies which is based on kernel configured HZ.
Internal kernel jiffies are not a proper unit for any userspace API.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some flesh to ipv4_sysctl_init_net and ipv4_sysctl_exit_net,
i.e. copy the table, alter .data pointers and register it per-net.
Other ipv4_table's sysctls are now global, but this is going to
change once sysctl permissions patches migrate from -mm tree to
mainline in 2.6.26 merge window :)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialization is moved to icmp_sk_init, all the places, that
refer to them use init_net for now.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes adding pernet_operations, empty init and exit
hooks and a bit of changes in sysctl_ipv4_init just not to
have this part in next patches.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In strategy_allowed_congestion_control of the 2.6.24 kernel, when
sysctl_string return 1 on success,it should call
tcp_set_allowed_congestion_control to set the allowed congestion
control.But, it don't. the sysctl_string return 1 on success,
otherwise return negative, never return 0.The patch fix the problem.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation for sysctl netns-ization.
Move the ctl tables to the files, where the tuning
variables reside. Plus make the helpers to register
the tables.
This will simplify the later patches and will keep
similar things closer to each other.
ipv4, ipv6 and conntrack_reasm are patched differently,
but the result is all the tables are in appropriate files.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes the most simple cases for netfilter.
The first part is tne queue modules for ipv4 and ipv6,
on which the net/ipv4/ and net/ipv6/ paths are reused
from the appropriate ipv4 and ipv6 code.
The conntrack module is also patched, but this hunk is
very small and simple.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
AFAIS these two entries should do the same thing - change the
forwarding state on ipv4_devconf and on all the devices.
I propose to merge the handlers together using ctl paths.
The inet_forward_change() is static after this and I move
it higher to be closer to other "propagation" helpers and
to avoid diff making patches based on { and } matching :)
i.e. - make them easier to read.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the same as I did for the net/core/ table in the
second patch in his series: use the paths and isolate the
whole table in the .c file.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes several cleanups:
* tune Makefile to compile out this file when SYSCTL=n. Now
it looks like net/core/sysctl_net_core.c one;
* move the ipv4_config to af_inet.c to exist all the time;
* remove additional sysctl_ip_nonlocal_bind declaration
(it is already declared in net/ip.h);
* remove no nonger needed ifdefs from this file.
This is a preparation for using ctl paths for net/ipv4/
sysctl table.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: "Sam Jansen" <sjansen@google.com>
sysctl_tcp_congestion_control seems to have a bug that prevents it
from actually calling the tcp_set_default_congestion_control
function. This is not so apparent because it does not return an error
and generally the /proc interface is used to configure the default TCP
congestion control algorithm. This is present in 2.6.18 onwards and
probably earlier, though I have not inspected 2.6.15--2.6.17.
sysctl_tcp_congestion_control calls sysctl_string and expects a successful
return code of 0. In such a case it actually sets the congestion control
algorithm with tcp_set_default_congestion_control. Otherwise, it returns the
value returned by sysctl_string. This was correct in 2.6.14, as sysctl_string
returned 0 on success. However, sysctl_string was updated to return 1 on
success around about 2.6.15 and sysctl_tcp_congestion_control was not updated.
Even though sysctl_tcp_congestion_control returns 1, do_sysctl_strategy
converts this return code to '0', so the caller never notices the error.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a justifying patch for Stephen's patches. Stephen's patches
disallows using a port range of one single port and brakes the meaning
of the 'remaining' variable, in some places it has different meaning.
My patch gives back the sense of 'remaining' variable. It should mean
how many ports are remaining and nothing else. Also my patch allows
using a single port.
I sure we must be able to use mentioned port range, this does not
restricted by documentation and does not brake current behavior.
usefull links:
Patches posted by Stephen Hemminger
http://marc.info/?l=linux-netdev&m=119206106218187&w=2http://marc.info/?l=linux-netdev&m=119206109918235&w=2
Andrew Morton's comment
http://marc.info/?l=linux-kernel&m=119248225007737&w=2
1. Allows using a port range of one single port.
2. Gives back sense of 'remaining' variable.
Signed-off-by: Anton Arapov <aarapov@redhat.com>
Acked-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tcp_available_congestion_control does not even attempt being read
from sys_sysctl, and ipfrag_max_dist while it works allows setting of invalid
values using sys_sysctl.
So just kill the binary sys_sysctl support for these sysctls. If the support
is not important enough to test and get right it probably isn't important
enough to keep.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alexey Dobriyan <adobriyan@sw.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some sysctl variables are used to tune the frag queues
management and it will be useful to work with them in
a common way in the future, so move them into one
structure, moreover they are the same for all the frag
management codes.
I don't place them in the existing inet_frags object,
introduced in the previous patch for two reasons:
1. to keep them in the __read_mostly section;
2. not to export the whole inet_frags objects outside.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expansion of original idea from Denis V. Lunev <den@openvz.org>
Add robustness and locking to the local_port_range sysctl.
1. Enforce that low < high when setting.
2. Use seqlock to ensure atomic update.
The locking might seem like overkill, but there are
cases where sysadmin might want to change value in the
middle of a DoS attack.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the ipv4_devconf config members (everything except
sysctl) to an array. This allows easier manipulation which will be
needed later on to provide better management of default config values.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
New sysctl tcp_frto_response is added to select amongst these
responses:
- Rate halving based; reuses CA_CWR state (default)
- Very conservative; used to be the only one available (=1)
- Undo cwr; undoes ssthresh and cwnd reductions (=2)
The response with rate halving requires a new parameter to
tcp_enter_cwr because FRTO has already reduced ssthresh and
doing a second reduction there has to be prevented. In addition,
to keep things nice on 80 cols screen, a local variable was
added.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow normal users to only choose among a restricted set of congestion
control choices. The default is reno and what ever has been configured
as default. But the policy can be changed by administrator at any time.
For example, to allow any choice:
cp /proc/sys/net/ipv4/tcp_available_congestion_control \
/proc/sys/net/ipv4/tcp_allowed_congestion_control
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create /proc/sys/net/ipv4/tcp_available_congestion_control
that reflects currently available TCP choices.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setting of the default congestion control was buried in
the sysctl code so it would not be done properly if SYSCTL was
not enabled.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change how default TCP congestion control is chosen. Don't just use
last installed module, instead allow selection during configuration,
and make sure and use the default regardless of load order.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Commercial IP Security Option (CIPSO) to the IPv4
network stack. CIPSO has become a de-facto standard for
trusted/labeled networking amongst existing Trusted Operating Systems
such as Trusted Solaris, HP-UX CMW, etc. This implementation is
designed to be used with the NetLabel subsystem to provide explicit
packet labeling to LSM developers.
The CIPSO/IPv4 packet labeling works by the LSM calling a NetLabel API
function which attaches a CIPSO label (IPv4 option) to a given socket;
this in turn attaches the CIPSO label to every packet leaving the
socket without any extra processing on the outbound side. On the
inbound side the individual packet's sk_buff is examined through a
call to a NetLabel API function to determine if a CIPSO/IPv4 label is
present and if so the security attributes of the CIPSO label are
returned to the caller of the NetLabel API function.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A lot of people have asked for a way to disable tcp_cwnd_restart(),
and it seems reasonable to add a sysctl to do that.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sysctl net.ipv4.ip_autoconfig is a legacy value that is not used.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any socket recv of less than this ammount will not be offloaded
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in the dark ages, we had to be conservative and only allow 15-bit
window fields if the window scale option was not negotiated. Some
ancient stacks used a signed 16-bit quantity for the window field of
the TCP header and would get confused.
Those days are long gone, so we can use the full 16-bits by default
now.
There is a sysctl added so that we can still interact with such old
stacks
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implementation of packetization layer path mtu discovery for TCP, based on
the internet-draft currently found at
<http://www.ietf.org/internet-drafts/draft-ietf-pmtud-method-05.txt>.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
To help in reducing the number of include dependencies, several files were
touched as they were getting needed headers indirectly for stuff they use.
Thanks also to Alan Menegotto for pointing out that net/dccp/proto.c had
linux/dccp.h include twice.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another spin of Herbert Xu's "safer ip reassembly" patch
for 2.6.16.
(The original patch is here:
http://marc.theaimsgroup.com/?l=linux-netdev&m=112281936522415&w=2
and my only contribution is to have tested it.)
This patch (optionally) does additional checks before accepting IP
fragments, which can greatly reduce the possibility of reassembling
fragments which originated from different IP datagrams.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an updated version of the RFC3465 ABC patch originally
for Linux 2.6.11-rc4 by Yee-Ting Li. ABC is a way of counting
bytes ack'd rather than packets when updating congestion control.
The orignal ABC described in the RFC applied to a Reno style
algorithm. For advanced congestion control there is little
change after leaving slow start.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Of this type, mostly:
CHECK net/ipv6/netfilter.c
net/ipv6/netfilter.c:96:12: warning: symbol 'ipv6_netfilter_init' was not declared. Should it be static?
net/ipv6/netfilter.c:101:6: warning: symbol 'ipv6_netfilter_fini' was not declared. Should it be static?
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That groups all of the tables and variables associated to the TCP timewait
schedulling/recycling/killing code, that now can be isolated from the TCP
specific code and used by other transport protocols, such as DCCP.
Next changeset will move this code to net/ipv4/inet_timewait_sock.c
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow TCP to have multiple pluggable congestion control algorithms.
Algorithms are defined by a set of operations and can be built in
or modules. The legacy "new RENO" algorithm is used as a starting
point and fallback.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch alows you to change the source address of icmp error
messages. It applies cleanly to 2.6.11.11 and retains the default
behaviour.
In the old (default) behaviour icmp error messages are sent with the ip
of the exiting interface.
The new behaviour (when the sysctl variable is toggled on), it will send
the message with the ip of the interface that received the packet that
caused the icmp error. This is the behaviour network administrators will
expect from a router. It makes debugging complicated network layouts
much easier. Also, all 'vendor routers' I know of have the later
behaviour.
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Eric Dumazet