Belkin's Connect N150 Wireless USB Adapter, model F7D1101 version 2, uses ID 0x945b.
Chipset info: rt: 3390, rf: 000b, rev: 3213.
I have just bought one, which started to work perfectly after the ID was added through this patch.
Signed-off-by: Eduardo Bacchi Kienetz <eduardo@kienetz.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implementing this callback function will cause mac80211 refrain from
going to powersave state when there are still untransmitted TX frames
in the queues.
This would exactly mimic the behaviour of the legacy vendor driver which
also doesn't go in powersave mode if there are still TX frames that are not
transmitted.
This should make powersaving and rt2x00 a better couple.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sitecom WLA4000 (USB ID 0x0df6:0x0060) is an RT3072 chipset.
Sitecom WLA5000 (USB ID 0x0df6:0x0062) is an RT3572 chipset.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Wim Vander Schelden <wim@fixnum.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently a lot of actions that can be done without the queue's tx lock
being held are done inside the locked area.
Move them out to have a leaner and meaner code that operates while the
tx lock is being held.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions that create the tx descriptor structure do not operate on
a queue entry at all. Signal this fact in the code by not providing a
queue entry as a parameter, but the rt2x00 device structure and the skb
directly.
This patch is a preparation for reducing the time a queue is locked for
a tx operation.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00 driver gets frequent occurrences of the following error message
when operating under load:
phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the
non-full queue 2.
This is caused by simultaneous attempts from mac80211 to send a frame via
rt2x00, which are not properly serialized inside rt2x00queue_write_tx_frame,
causing the second frame to fail sending with the above mentioned error
message.
Fix this by introducing a per-queue spinlock to serialize the TX operations
on that queue.
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When module is reloaded, device may fail to work, with messages:
[ 342.211926] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x0059, type=2.
[ 342.314254] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004a, type=2.
[ 342.416458] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 3183 max 2432.
[ 342.518605] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00c9, type=2.
[ 342.620836] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00ae, type=1.
[ 342.723201] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[ 342.825399] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[ 342.927624] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[ 343.029804] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2491 max 2432.
[ 343.132008] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2576 max 2432.
[ 343.234326] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004c, type=1.
[ 343.438723] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00e6, type=1.
Whereas replugging device make it functional. To solve that problem
force reset device during probe.
With patch messages are gone. Unfortunately device may sometimes
still does not operate correctly after module reload (fail to receive
data after associate), but such cases are rarer than without the patch.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes rxdesc descriptor provided by hardware contains invalid
(random) data. For example rxdesc.size can be bigger than actual
size of the buffer. When this happen rt2x00crypto_rx_insert_iv()
corrupt memory doing memmove outside of buffer boundaries.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoid queue and run autowakeup_work when device is not present anymore.
That prevent rmmod and device remove crash introduced by:
commit 1c0bcf89d8
Author: Ivo van Doorn <ivdoorn@gmail.com>
Date: Sat Apr 30 17:18:18 2011 +0200
rt2x00: Add autowake support for USB hardware
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that support for these devices has been added we can enable them
by default and remove the Kconfig not on support for these devices to
be non-functional.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These two functions are only used by rt2800usb so they don't have to be
in rt2800lib.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lock is only used in the TX path and thus in process context. Therefore
we can use a much lighter spinlock variant.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(based on an earlier patch submitted by Shiang)
Add support for RT3572/RT3592/RT3592+Bluetooth combo card
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(split off from the earlier RT35xx patch submitted by Shiang)
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(split off from the earlier RT35xx patch submitted by Shiang)
There's no point in enabling the PA_PE bits for the bands that we are
not active on.
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We make oldconfig every time when a new kernel arrives, but
if we don't have such a device(I guess this is the most common
case for a new device), the default value should be 'n' so
that the kernel size we build doesn't grow up too much quickly.
For anyone who has the device, it is OK for them to turn it on
by themselves.
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txstatus_timer should only be deleted for USB devices, as it is only
initialized for USB devices.
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch:
rt2x00: Make rt2x00_queue_entry_for_each more flexible
commit: 10e11568ca
introduced a severe regression on the throughput
for USB hardware. It turns out that the exiting of
the rt2x00queue_for_each_entry() was done too early.
The exact cause for this regression is unknown,
but by disabling the premature exiting of the loop
seems to resolve the issue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com>
Reported-by: Balint Viragh <bviragh@dension.com>
Tested-by: Balint Viragh <bviragh@dension.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add necessary RF chipset define and basic support for these devices.
Tested-by: Juan Carlos Garza <juancarlosgarza@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB drivers don't support automatically waking up when in powersaving mode,
add a work object which will wakeup the device in time to receive the next beacon.
Based on that beacon, we either go back into powersaving mode, or we remain awake
to receive the buffered frames for our station.
Some part of the code, especially rt2x00lib_find_ie and rt2x00lib_rxdone_check_ps
are inspired on the code from carl9170.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use flag instead of re-reading the eeprom every time.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2800lib.c the rt2800_init_eeprom function the same eeprom
words were read multiple times, due to inefficient ordering of the
eeprom checks.
Reorder the checks so that each EEPROM word only has to be read once.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch
rt2x00: Optimize register access in rt2800pci
from Helmut Schaa missed one register call, namely
the rt2800_register_multiwrite which should be changed
to rt2x00pci_register_multiwrite.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add recycling functionality to rt2x00usb_register_read_async.
When the callback function returns true, resubmit the urb to
read the register again.
This optimizes the rt2800usb driver when multiple TX status reports
are pending in the register, because now we don't need to allocate
the rt2x00_async_read_data and urb structure each time.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When no TX status was available, the default timeout
of 20ms is a bit high. The frame is highly likely already
send out, so the TX status should be available within
only a few milliseconds.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the get_antenna and set_antenna callback functions, which will
allow clients to control the antenna for all non-11n hardware (Antenna handling
in rt2800 is still a bit magical, so we can't use the set_antenna for those drivers
yet).
To best support the set_antenna callback some modifications are needed in the
diversity handling. We should never look at the default antenna settings to determine
if software diversity is enabled. Instead we should set the diversity flag when
possible, which will allow the link_tuner to automatically pick up the tuning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the get_ringparam callback function we can export ring parameters
to ethtool through the mac80211 interface.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All register reads/writes in rt2800usb were previously done with
rt2800_register_read/rt2800_register_write. These however indirectly
call rt2x00usb_register_read/rt2x00usb_register_write which adds an
additional overhead of at least one call and several move instructions
to each register access.
Replacing the calls to rt2800_register_read/rt2800_register_write with
direct calls to rt2x00usb_register_read/rt2x00usb_register_write gets
rid of quite a number of instructions in the drivers hotpaths (IRQ
handling and txdone handling).
For consistency replace all references to rt2800_register_read/write
with the rt2x00usb_register_read/write variants.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All register reads/writes in rt2800pci were previously done with
rt2800_register_read/rt2800_register_write. These however indirectly
call rt2x00pci_register_read/rt2x00pci_register_write which adds an
additional overhead of at least one call and several move instructions
to each register access.
Replacing the calls to rt2800_register_read/rt2800_register_write with
direct calls to rt2x00pci_register_read/rt2x00pci_register_write gets
rid of quite a number of instructions in the drivers hotpaths (IRQ
handling and txdone handling).
For consistency replace all references to rt2800_register_read/write
with the rt2x00pci_register_read/write variants.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The two functions that are in rt2x00ht.c can be much better placed
closer to the places where the call-sites of these functions are (one
in rt2x00config.c and one in rt2x00queue.c) allowing us to make these
functions static.
Also, conditional compilations doesn't seem to be necessary anymore as
802.11n support is quite common nowadays.
This makes the code a bit easier readable and searchable.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code seems to be feature-complete, so no reason to not enable
these devices by default.
Also, remove the sentence about the support for these devices being
non-functional.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt33xx devices support for both PCI and USB devices has been in
the tree for a couple of months now, and seems to be functional and
not in a worse shape than the support for rt28xx and rt30xx devices.
No longer mark it as experimental and enable the support for these
devices by default.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add USB IDs that are listed in the latest Ralink Windows and/or Linux drivers.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both USB and PCI drivers allow a system administrator to dynamically add
USB/PCI IDs to the device table that a driver supports via the
/sys/bus/{usb,pci,pci_express}/drivers/<driver-name>/new_id files.
However, for the rt2x00 drivers using this method currently crashes the
system with a NULL pointer failure.
This is due to the set-up of rt2x00 where the probe functions require a
rt2x00_ops structure in the driver_info field of the probed device. As
this field is empty for the dynamically added devices this fails for
these devices.
Fix this by introducing driver-specific probe wrappers that do nothing
but calling the bus-specific probe functions with the rt2x00_ops structure
as an argument, rather than depending on the driver_info field.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the USB ID entry from the unknown devices to the list of RT35xx based
devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows the compiler to perform the necessary bitfield calculations
during compile time instead of run time and thus reduces the number of
instructions to run during each tasklet invocation. This should improve
performance in the RX hotpath.
This comes at the cost of a slight increase in the module size (for
example rt2800pci):
Before:
text data bss dec hex filename
14133 832 4 14969 3a79 drivers/net/wireless/rt2x00/rt2800pci.ko
After:
text data bss dec hex filename
14149 832 4 14985 3a89 drivers/net/wireless/rt2x00/rt2800pci.ko
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When powersaving is enabled, assocaition times are very high
(for WPA2 networks, the time can easily be around the 3 seconds).
This is caused, because the flushing of the queues takes
too much time. Without the flushing callback mac80211 assumes
a timeout of 100ms while scanning. Limit all flush waiting
loops to the same maximum.
We can apply this maximum by passing the drop status to the
driver, which makes sure the driver performs extra actions
during the waiting for the queue to become empty.
After these changes, association times fall within the
healthy range of ~0.6 seconds with powersaving enabled.
The difference between association time between powersaving
enabled and disabled is now only ~0.1 second (which can also
be due to the measuring method).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX status is reported by the hardware when a packet has been
sent (or after TX failed after possible retries), which is some
time after the DMA completion. Since the rt2800usb hardware can
not signal interrupts we have to use a timer, otherwise the
TX status would only be read by the next packet's TX DMA
completion, or by the watchdog thread.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog just triggers rt2800usb_work_txdone() when it
detects a TX status timeout, thus rt2800usb_work_txdone() needs to
handle this case.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a timestamp to each queue entry which is updated whenever
the status of the entry changes, and remove the per-queue
timestamps. The previous check was incorrect and caused both
false positives and false negatives.
With the corrected check it comes apparent that the TX status
usually times out on rt2800usb unless there is sufficient traffic
(i.e. the next TX will complete the previous TX status).
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to fix the "TX status report missed" warnings
by reading the TX_STA_FIFO entries as quickly as possible.
The TX_STA_FIFO is too small in hardware, thus reading
it only from the workqueue is too slow and entries get lost.
Start an asynchronous read of the TX_STA_FIFO directly from
the TX URB completion callback (atomic context, thus it cannot
use the blocking rt2800_register_read()). If the async
read returns a valid FIFO entry, it is pushed into a larger
FIFO inside struct rt2x00_dev, until rt2800_txdone() picks
it up.
A .tx_dma_done callback is added to struct rt2x00lib_ops
to trigger the async read from the URB completion callback.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use TXOP_HTTXOP for beacons to stay in sync with the legacy drivers.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bring the TX_SW_CFG2 initialisation for rt305x devices in sync with the
ralink legacy drivers.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eduardo Bacchi Kienetz