This moves off of the board_pci_channels[] approach for bus registration
and over to a cleaner register_pci_controller(), all derived from the
MIPS code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Not all PCI channels have non-translatable memory windows, this is a
special property of the on-chip PCIC with its 0xfd00... mapping, handle
this explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates the pci_iomap() definitions and reworks how the I/O
port base is handled. PCI channels can register their own I/O map base,
or if none is provided, the system-wide generic I/O base is used instead.
Functionally nothing changes, while this allows us to kill off lots of
I/O address special casing and lookups.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is left over cruft that hasn't been used by anything in a long time,
kill off bits that weren't purged previously.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This introduces a saner pcibios_align_resource() that can be used
regardless of whether pci-auto or pci-new are being used, and
consolidates it in pci-lib.c.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The new PCI code wants its own bus<->resource mappings instead of the
generic equivalents, so drop the asm-generic include in preparation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adds a __get_pci_io_base() function which is used to match a port range
against struct pci_channel. This allows us to detect if a port range is
assigned to pci or happens to be legacy port io. While at it, remove unused
cpu-specific cruft.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes the code to use __is_pci_memory() instead of
is_pci_memaddr(). __is_pci_memory() loops through all the pci
channels on the system to match memory windows.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store the io window base address in struct pci_channel and use that one
instead of SH77xx_PCI_IO_BASE.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store the base address of the pci host controller registers in struct
pci_channel and use the address in pci_read_reg() and pci_write_reg().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store a struct pci_channel pointer in bus->sysdata. This makes whatever
struct pci_channel assigned to a bus available for sh4_pci_read() and
sh4_pci_write(). We also modify PCIBIOS_MIN_IO and PCIBIOS_MIN_MEM to
use bus->sysdata - this to gives us support for multiple pci channels.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds an init callback to struct pci_channel and makes sure
it is initialized properly. Code is added to call this init function
from pcibios_init(). Return values are adjusted and a warning is is
printed if init fails.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: sh7785lcr: Map whole PCI address space.
sh: Fix up DSP context save/restore.
sh: Fix up number of on-chip DMA channels on SH7091.
sh: update defconfigs.
sh: Kill off broken direct-mapped cache mode.
sh: Wire up ARCH_HAS_DEFAULT_IDLE for cpuidle.
sh: Add a command line option for disabling I/O trapping.
sh: Select ARCH_HIBERNATION_POSSIBLE.
sh: migor: Fix up CEU use flags.
input: migor_ts: add wakeup support
rtc: rtc-sh: use set_irq_wake()
input: sh_keysc: use enable/disable_irq_wake()
sh: intc: set_irq_wake() support
sh: intc: install enable, disable and shutdown callbacks
clocksource: sh_cmt: use remove_irq() and remove clockevent workaround
sh: ap325 and Migo-R use new sh_mobile_ceu_info flags
sh: Fix up -Wformat-security whining.
sh: ap325rxa: Add ov772x support, again.
sh: Sanitize asm/mmu.h for assembly use.
sh: Tidy up sh7786 pinmux table.
...
There were a number of issues with the DSP context save/restore code,
mostly left-over relics from when it was introduced on SH3-DSP with
little follow-up testing, resulting in things like task_pt_dspregs()
referencing incorrect state on the stack.
This follows the MIPS convention of tracking the DSP state in the
thread_struct and handling the state save/restore in switch_to() and
finish_arch_switch() respectively. The regset interface is also updated,
which allows us to finally be rid of task_pt_dspregs() and the special
cased task_pt_regs().
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pass the original flags to rwlock arch-code, so that it can re-enable
interrupts if implemented for that architecture.
Initially, make __raw_read_lock_flags and __raw_write_lock_flags stubs
which just do the same thing as non-flags variants.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpuidle wants ARCH_HAS_DEFAULT_IDLE defined in order to use the
default idle loop. So, make it accessible and enable it for all
sh machines.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the ifndef __ASSEMBLY__ preprocessor to allow the
defines in the file to be used also in assembly code.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Everyone defines it, and only one person uses it
(arch/mips/sgi-ip27/ip27-nmi.c). So just open code it there.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-mips@linux-mips.org
Rework the hd64461 demuxer code to fix the HD64461 level-triggered
interrupts handling, using handle_level_irq() as needed.
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the ARM change from Aaro Koskinen:
When unmapping N pages (e.g. shared memory) the amount of TLB
flushes done can be (N*PAGE_SIZE/ZAP_BLOCK_SIZE)*N although it
should be N at maximum. With PREEMPT kernel ZAP_BLOCK_SIZE is 8
pages, so there is a noticeable performance penalty when
unmapping a large VMA and the system is spending its time in
flush_tlb_range().
The problem is that tlb_end_vma() is always flushing the full VMA
range. The subrange that needs to be flushed can be calculated by
tlb_remove_tlb_entry(). This approach was suggested by Hugh
Dickins, and is also used by other arches.
The speed increase is roughly 3x for 8M mappings and for larger
mappings even more.
Bits and peices are taken from the ARM patch as well as the existing
arch/um implementation that is quite similar.
The end result is a significant reduction in both partial and full TLB
flushes initiated through flush_tlb_range().
At the same time, the nommu implementation was broken, had a superfluous
cache flush, and subsequently would have triggered a BUG_ON() if a
code-path had triggered it. Tidy this up for correctness and provide a
nopped-out implementation there.
More background on the initial discussion can be found at:
http://marc.info/?t=123609820900002&r=1&w=2http://marc.info/?t=123660375800003&r=1&w=2
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for extended ASIDs (up to 16-bits) on newer SH-X3 cores
that implement the PTAEX register and respective functionality. Presently
only the 65nm SH7786 (90nm only supports legacy 8-bit ASIDs).
The main change is in how the PTE is written out when loading the entry
in to the TLB, as well as in how the TLB entry is selectively flushed.
While SH-X2 extended mode splits out the memory-mapped U and I-TLB data
arrays for extra bits, extended ASID mode splits out the address arrays.
While we don't use the memory-mapped data array access, the address
array accesses are necessary for selective TLB flushes, so these are
implemented newly and replace the generic SH-4 implementation.
With this, TLB flushes in switch_mm() are almost non-existent on newer
parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.
To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the clk_set_parent/clk_get_parent routines to the sh
clock framework.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds DMA support for newer SH-4A CPUs, particularly SH7763/64/80/85.
This also enables multi IRQ support for platforms that have multiple
vectors bound to the same IRQ source.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.
P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.
To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.
The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.
Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786-based Urquell board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786 CPU subtype.
While this is a dual-core CPU, only UP is supported for now. L2 cache
support is likewise not yet implemented.
More information on this particular CPU subtype is available at:
http://www.renesas.com/fmwk.jsp?cnt=sh7786_root.jsp&fp=/products/mpumcu/superh_family/sh7780_series/sh7786_group/
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH-3 does not support 'pref'-based prefetching, only SH-2A and SH-4A
parts do. Remove SH-3 from the list.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Prefetch early exception data. There is unused space in our
exception handler cache line anyway, so this is almost free.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove EXPEVT vector from the stack, lookup_exception_vector()
for sh3/sh4/sh4a is already using k2 to get the vector.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
User space can request hardware and/or software time stamping.
Reporting of the result(s) via a new control message is enabled
separately for each field in the message because some of the
fields may require additional computation and thus cause overhead.
User space can tell the different kinds of time stamps apart
and choose what suits its needs.
When a TX timestamp operation is requested, the TX skb will be cloned
and the clone will be time stamped (in hardware or software) and added
to the socket error queue of the skb, if the skb has a socket
associated with it.
The actual TX timestamp will reach userspace as a RX timestamp on the
cloned packet. If timestamping is requested and no timestamping is
done in the device driver (potentially this may use hardware
timestamping), it will be done in software after the device's
start_hard_xmit routine.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework and simplify the sched_clock and clocksource code. Instead
of registering the clocksource in a shared file we move it into the
tmu driver. Also, add code to handle sched_clock in the case of no
clocksource.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix macros start_thread and user_stack_pointer.
When these macros aren't called with a variable named regs as second
argument, this will result in a build failure.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that atomic_t is a generic opaque type for all architectures, it is
unwise to use intimate knowledge of its internals when manipulating it.
Instead of relying on the "counter" member being at offset 0 from the
beginning of an atomic_t, explicitly reference the member. This guards
us from any changes to the layout of the beginning of the atomic_t type.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When dereferencing the memory address contained in a register and
modifying the value at that memory address, the register should not be
listed in the inline asm outputs. The value at the memory address is an
output (which is taken care of with the "memory" clobber), not the register.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This corrects a deadlock encountered on ap325 in the cases where the
mutex is contended and the slow-path needs to be fallen back upon.
Signed-off-by: Takashi YOSHII <yoshii.takashi@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The T-bit manipulation for syscall error checking had the side effect of
spuriously returning ERESTART* errno values over EINTR. So, we simplify
the error checking a bit and leave the T-bit alone.
Reported-by: Kaz Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the SuperH gpio code to make use of gpiolib. The
gpiolib callbacks get() and set() are lockless, but we use our own
spinlock for the other operations to make sure hardware register
bitfield accesses stay atomic.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt