Use newly added GPIO defines GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT instead of using hard-coded 1 and 0.
Main benefit is to make it easier to see which values mean IN and which
OUT. As a side effect this helps GPIO framework to change the direction
defines to something else if ever needed.
Please note that return value from get_direction call on
pinctrl-axp209 driver was changed. Previously pinctrl-axp209 might have
returned value 2 for direction INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Link: https://lore.kernel.org/r/20200214135712.GA14557@localhost.localdomain
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
series:
Core changes:
- Avoid taking direct references to device tree-supplied
device names: these may changed at runtime under certain
circumstances to kstrdup them.
GPIO related:
- Work is ongoing to move to passing the irqchip along as a
templated struct gpio_irq_chip when adding a standard
gpiolib-based irqchip to a GPIO controller, a few patches
in this cycle switches a few pin control drivers over to
using this method.
New hardware support:
- Intel Lightning Mountain SoC pin controller and GPIO
support, a first Intel platform to use device tree rather
than ACPI to configure the system. News reports says that
this SoC is a network processor.
- Qualcomm MSM8976 and MSM8956
- Qualcomm PMIC GPIO now also supports PM6150 and PM6150L
- Qualcomm SPMI MPP and SPMI GPIO for PM8950 and PMI8950
- Rockchip RK3308
- Renesas R8A77961
- Allwinner Meson-A1
Driver improvements:
- get_multiple and set_multiple support for the AT91-PIO4 driver.
- Convert Qualcomm SSBI GPIO to use the hierarchical IRQ helpers
in the GPIOlib irqchip.
-----BEGIN PGP SIGNATURE-----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=uPLY
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for v5.5.
It is pretty much business as usual, the most interesting thing I
think is the pin controller for a new Intel chip called Lightning
Mountain, which is according to news reports some kind of embedded
network processor and what is surprising about it is that Intel have
decided to use device tree to describe the system rather than ACPI
that they have traditionally favored.
Core changes:
- Avoid taking direct references to device tree-supplied device
names: these may changed at runtime under certain circumstances to
kstrdup them.
GPIO related:
- Work is ongoing to move to passing the irqchip along as a templated
struct gpio_irq_chip when adding a standard gpiolib-based irqchip
to a GPIO controller, a few patches in this cycle switches a few
pin control drivers over to using this method.
New hardware support:
- Intel Lightning Mountain SoC pin controller and GPIO support, a
first Intel platform to use device tree rather than ACPI to
configure the system. News reports says that this SoC is a network
processor.
- Qualcomm MSM8976 and MSM8956
- Qualcomm PMIC GPIO now also supports PM6150 and PM6150L
- Qualcomm SPMI MPP and SPMI GPIO for PM8950 and PMI8950
- Rockchip RK3308
- Renesas R8A77961
- Allwinner Meson-A1
Driver improvements:
- get_multiple and set_multiple support for the AT91-PIO4 driver.
- Convert Qualcomm SSBI GPIO to use the hierarchical IRQ helpers in
the GPIOlib irqchip"
* tag 'pinctrl-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (93 commits)
pinctrl: ingenic: Add OTG VBUS pin for the JZ4770
pinctrl: ingenic: Handle PIN_CONFIG_OUTPUT config
pinctrl: Fix Kconfig indentation
pinctrl: lewisburg: Update pin list according to v1.1v6
MAINTAINERS: Replace my email by one @kernel.org
pinctrl: armada-37xx: Fix irq mask access in armada_37xx_irq_set_type()
dt-bindings: pinctrl: intel: Add for new SoC
pinctrl: Add pinmux & GPIO controller driver for a new SoC
pinctrl: rza1: remove unnecessary static inline function
pinctrl: meson: add pinctrl driver support for Meson-A1 SoC
pinctrl: meson: add a new callback for SoCs fixup
pinctrl: nomadik: db8500: Add mc0_a_2 pin group without direction control
dt-bindings: pinctrl: Convert generic pin mux and config properties to schema
pinctrl: cherryview: Missed type change to unsigned int
pinctrl: intel: Missed type change to unsigned int
pinctrl: use devm_platform_ioremap_resource() to simplify code
pinctrl: just return if no valid maps
dt-bindings: pinctrl: qcom-pmic-mpp: Add support for PM/PMI8950
pinctrl: qcom: spmi-mpp: Add PM/PMI8950 compatible strings
dt-bindings: pinctrl: qcom-pmic-gpio: Add support for PM/PMI8950
...
With stmfx_pinctrl_gpio_init_valid_mask callback, gpio_valid_mask was used
to initialize gpiochip valid_mask for gpiolib. But gpio_valid_mask was not
yet initialized. gpio_valid_mask required gpio-ranges to be registered,
this is the case after gpiochip_add_data call. But init_valid_mask
callback is also called under gpiochip_add_data. gpio_valid_mask
initialization cannot be moved before gpiochip_add_data because
gpio-ranges are not registered.
So, it is not possible to use init_valid_mask callback.
To avoid this issue, get rid of valid_mask and rely on ranges.
Fixes: da9b142ab2 ("pinctrl: stmfx: Use the callback to populate valid_mask")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20191104100908.10880-1-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an STMFX IO is used as interrupt through the interrupt-controller
binding, the STMFX driver should configure this IO as input. Default
value of STMFX IO direction is input, but if the IO is used as output
before the interrupt use, it will not work without these callbacks.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20191009091606.17283-1-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dev_get_platdata(&pdev->dev) returns a pointer on struct stmfx_pinctrl,
not on struct stmfx (platform_set_drvdata(pdev, pctl); in probe).
Pointer on struct stmfx is stored in driver data of pdev parent (in probe:
struct stmfx *stmfx = dev_get_drvdata(pdev->dev.parent);).
Fixes: 1490d9f841 ("pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20191004122342.22018-1-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to
the Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver.
-----BEGIN PGP SIGNATURE-----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=2nNz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
After we switched the two drivers that have .need_valid_mask
set to use the callback for setting up the .valid_mask,
we can just use the presence of the .init_valid_mask()
callback (or the OF reserved ranges, nota bene) to determine
whether to allocate the mask or not and we can drop the
.need_valid_mask field altogether.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819093058.10863-1-linus.walleij@linaro.org
This makes use of the existing callback to populate the
valid mask instead of iteratively setting it up during
probe.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819091140.622-1-linus.walleij@linaro.org
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-34-swboyd@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the following tab (coming from STMFX datasheet), updates
have to done in stmfx_pinconf_set function:
-"type" has to be set when "bias" is configured as "pull-up or pull-down"
-PIN_CONFIG_DRIVE_PUSH_PULL should only be used when gpio is configured as
output. There is so no need to check direction.
DIR | TYPE | PUPD | MFX GPIO configuration
----|------|------|---------------------------------------------------
1 | 1 | 1 | OUTPUT open drain with internal pull-up resistor
----|------|------|---------------------------------------------------
1 | 1 | 0 | OUTPUT open drain with internal pull-down resistor
----|------|------|---------------------------------------------------
1 | 0 | 0/1 | OUTPUT push pull no pull
----|------|------|---------------------------------------------------
0 | 1 | 1 | INPUT with internal pull-up resistor
----|------|------|---------------------------------------------------
0 | 1 | 0 | INPUT with internal pull-down resistor
----|------|------|---------------------------------------------------
0 | 0 | 1 | INPUT floating
----|------|------|---------------------------------------------------
0 | 0 | 0 | analog (GPIO not used, default setting)
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/1564053416-32192-1-git-send-email-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set create_link to inform pinctrl core that stmfx wants to create
link with its consumers.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drivers/pinctrl/pinctrl-stmfx.c:441 stmfx_pinctrl_irq_set_type() warn: bitwise AND condition is false here
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
smatch warnings:
drivers/pinctrl/pinctrl-stmfx.c:225 stmfx_pinconf_get() warn: unsigned 'dir' is never less than zero.
drivers/pinctrl/pinctrl-stmfx.c:228 stmfx_pinconf_get() warn: unsigned 'type' is never less than zero.
drivers/pinctrl/pinctrl-stmfx.c:231 stmfx_pinconf_get() warn: unsigned 'pupd' is never less than zero.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds pinctrl/GPIO driver for STMicroelectronics
Multi-Function eXpander (STMFX) GPIO expander.
STMFX is an I2C slave controller, offering up to 24 GPIOs.
The driver relies on generic pin config interface to configure the GPIOs.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Amelie Delaunay