If the two requests belong to the same io context, we will attempt
to lock the same lock twice. But swapping contexts is pointless in
that case, so just check for rioc == nioc before doing the double
lock and copy.
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Currently you must be root to set idle io prio class on a process. This
is due to the fact that the idle class is implemented as a true idle
class, meaning that it will not make progress if someone else is
requesting disk access. Unfortunately this means that it opens DOS
opportunities by locking down file system resources, hence it is root
only at the moment.
This patch relaxes the idle class a little, by removing the truly idle
part (which entals a grace period with associated timer). The
modifications make the idle class as close to zero impact as can be done
while still guarenteeing progress. This means we can relax the root only
criteria as well.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
These DMA drain buffer implementations in drivers are pretty horrible
to do in terms of manipulating the scatterlist. Plus they're being
done at least in drivers/ide and drivers/ata, so we now have code
duplication.
The one use case for this, as I understand it is AHCI controllers doing
PIO mode to mmc devices but translating this to DMA at the controller
level.
So, what about adding a callback to the block layer that permits the
adding of the drain buffer for the problem devices. The idea is that
you'd do this in slave_configure after you find one of these devices.
The beauty of doing it in the block layer is that it quietly adds the
drain buffer to the end of the sg list, so it automatically gets mapped
(and unmapped) without anything unusual having to be done to the
scatterlist in driver/scsi or drivers/ata and without any alteration to
the transfer length.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The io context sharing introduced a per-ioc spinlock, that would protect
the cfq io context lookup. That is a regression from the original, since
we never needed any locking there because the ioc/cic were process private.
The cic lookup is changed from an rbtree construct to a radix tree, which
we can then use RCU to make the reader side lockless. That is the performance
critical path, modifying the radix tree is only done on process creation
(when that process first does IO, actually) and on process exit (if that
process has done IO).
As it so happens, radix trees are also much faster for this type of
lookup where the key is a pointer. It's a very sparse tree.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch merges complete_request() into end_that_request_last()
for cleanup.
complete_request() was introduced by earlier part of this patch-set,
not to break the existing users of end_that_request_last().
Since all users are converted to blk_end_request interfaces and
end_that_request_last() is no longer exported, the code can be
merged to end_that_request_last().
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts 'uptodate' arguments of no longer exported
interfaces, end_that_request_first/last, to 'error', and removes
internal conversions for it in blk_end_request interfaces.
Also, this patch removes no longer needed end_io_error().
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch removes the following functions:
o end_that_request_first()
o end_that_request_chunk()
and stops exporting the functions below:
o end_that_request_last()
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds a variant of the interface, blk_end_bidi_request(),
which completes a bidi request.
Bidi request must be completed as a whole, both rq and rq->next_rq
at once. So the interface has 2 arguments for completion size.
As for ->end_io, only rq->end_io is called (rq->next_rq->end_io is not
called). So if special completion handling is needed, the handler
must be set to rq->end_io.
And the handler must take care of freeing next_rq too, since
the interface doesn't care of it if rq->end_io is not NULL.
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds a variant of the interface, blk_end_request_callback(),
which has driver callback feature.
Drivers may need to do special works between end_that_request_first()
and end_that_request_last().
For such drivers, blk_end_request_callback() allows it to pass
a callback function which is called between end_that_request_first()
and end_that_request_last().
This interface is only for fallback of other blk_end_request interfaces.
Drivers should avoid their tricky behaviors and use other interfaces
as much as possible.
Currently, only one driver, ide-cd, needs this interface.
So this interface should/will be removed, after the driver removes
such tricky behaviors.
o ide-cd (cdrom_newpc_intr())
In PIO mode, cdrom_newpc_intr() needs to defer end_that_request_last()
until the device clears DRQ_STAT and raises an interrupt after
end_that_request_first().
So end_that_request_first() and end_that_request_last() are called
separately in cdrom_newpc_intr().
This means blk_end_request_callback() has to return without
completing request even if no leftover in the request.
To satisfy the requirement, callback function has return value
so that drivers can tell blk_end_request_callback() to return
without completing request.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts core parts of block layer to use blk_end_request
interfaces. Related 'uptodate' arguments are converted to 'error'.
'dequeue' argument was originally introduced for end_dequeued_request(),
where no attempt should be made to dequeue the request as it's already
dequeued.
However, it's not necessary as it can be checked with
list_empty(&rq->queuelist).
(Dequeued request has empty list and queued request doesn't.)
And it has been done in blk_end_request interfaces.
As a result of this patch, end_queued_request() and
end_dequeued_request() become identical. A future patch will merge
and rename them and change users of those functions.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds/exports functions to get the size of request in bytes.
They are useful because blk_end_request interfaces take bytes
as a completed I/O size instead of sectors.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds 2 new interfaces for request completion:
o blk_end_request() : called without queue lock
o __blk_end_request() : called with queue lock held
blk_end_request takes 'error' as an argument instead of 'uptodate',
which current end_that_request_* take.
The meanings of values are below and the value is used when bio is
completed.
0 : success
< 0 : error
Some device drivers call some generic functions below between
end_that_request_{first/chunk} and end_that_request_last().
o add_disk_randomness()
o blk_queue_end_tag()
o blkdev_dequeue_request()
These are called in the blk_end_request interfaces as a part of
generic request completion.
So all device drivers become to call above functions.
To decide whether to call blkdev_dequeue_request(), blk_end_request
uses list_empty(&rq->queuelist) (blk_queued_rq() macro is added for it).
So drivers must re-initialize it using list_init() or so before calling
blk_end_request if drivers use it for its specific purpose.
(Currently, there is no driver which completes request without
re-initializing the queuelist after used it. So rq->queuelist
can be used for the purpose above.)
"Normal" drivers can be converted to use blk_end_request()
in a standard way shown below.
a) end_that_request_{chunk/first}
spin_lock_irqsave()
(add_disk_randomness(), blk_queue_end_tag(), blkdev_dequeue_request())
end_that_request_last()
spin_unlock_irqrestore()
=> blk_end_request()
b) spin_lock_irqsave()
end_that_request_{chunk/first}
(add_disk_randomness(), blk_queue_end_tag(), blkdev_dequeue_request())
end_that_request_last()
spin_unlock_irqrestore()
=> spin_lock_irqsave()
__blk_end_request()
spin_unlock_irqsave()
c) spin_lock_irqsave()
(add_disk_randomness(), blk_queue_end_tag(), blkdev_dequeue_request())
end_that_request_last()
spin_unlock_irqrestore()
=> blk_end_request() or spin_lock_irqsave()
__blk_end_request()
spin_unlock_irqrestore()
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Since the SCSI layer uses the request queues from the block layer, blktrace can
also be used to trace the requests to all SCSI devices (like SCSI tape drives),
not only disks. The only missing part is the ioctl interface to start and stop
tracing.
This patch adds the SETUP, START, STOP and TEARDOWN ioctls from blktrace to the
sg device files. With this change, blktrace can be used for SCSI devices like
for disks, e.g.: blktrace -d /dev/sg1 -o - | blkparse -i -
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
Now that the old kobject_init() function is gone, rename
kobject_init_ng() to kobject_init() to clean up the namespace.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the old kobject_add() function is gone, rename kobject_add_ng()
to kobject_add() to clean up the namespace.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the code to use the new kobject functions, cleaning up the
logic in doing so.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the code to use the new kobject functions, cleaning up the
logic in doing so.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the block devices to /sys/class/block. It will create a
flat list of all block devices, with the disks and partitions in one
directory. For compatibility /sys/block is created and contains symlinks
to the disks.
/sys/class/block
|-- sda -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda
|-- sda1 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda1
|-- sda10 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda10
|-- sda5 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda5
|-- sda6 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda6
|-- sda7 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda7
|-- sda8 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda8
|-- sda9 -> ../../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/sda9
`-- sr0 -> ../../devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0/block/sr0
/sys/block/
|-- sda -> ../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda
`-- sr0 -> ../devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0/block/sr0
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dynamically create the kset instead of declaring it statically. We also
rename block_subsys to block_kset to catch all users of this symbol
with a build error instead of an easy-to-ignore build warning.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need a "default" ktype for a kset. We should set this
explicitly every time for each kset. This change is needed so that we
can make ksets dynamic, and cleans up one of the odd, undocumented
assumption that the kset/kobject/ktype model has.
This patch is based on a lot of help from Kay Sievers.
Nasty bug in the block code was found by Dave Young
<hidave.darkstar@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The purpose of this is to allow stacked alignment settings, with the
ultimate queue alignment being set to the largest alignment requirement
in the stack.
The reason for this is so that the SCSI mid-layer can relax the default
alignment requirements (which are basically causing a lot of superfluous
copying to go on in the SG_IO interface) while allowing transports,
devices or HBAs to add stricter limits if they need them.
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently in BSG, errors returned in req->errors aren't passed back to
the calling programme (either via SG_IO or via read/write). Fix this,
while preserving the SCSI convention of returning status in
req->errors.
Now update libsas to return errors correctly instead of to ignore
them.
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
David Dillow reported broken blktrace timestamps. The reason
is cpu_clock() which is not a global time source.
Fix bkltrace timestamps by using ktime_get() like the networking
code does for packet timestamps. This also removes a whole lot
of complexity from bkltrace.c and shrinks the code by 500 bytes:
text data bss dec hex filename
2888 124 44 3056 bf0 blktrace.o.before
2390 116 44 2550 9f6 blktrace.o.after
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
elv_register() always returns 0, and there isn't anything it does where
it should return an error (the only error condition is so grave that
it's handled with a BUG_ON).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
New write batches currently start from where the last one completed.
We have no idea where the head is after switching batches, so this
makes little sense. Instead, start the next batch from the request
with the earliest deadline in the hope that we avoid a deadline
expiry later on.
Signed-off-by: Aaron Carroll <aaronc@gelato.unsw.edu.au>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Two comments refer to deadlines applying to reads only. This is
not the case.
Signed-off-by: Aaron Carroll <aaronc@gelato.unsw.edu.au>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Use msecs_to_jiffies() and jiffies_to_msecs() in scsi_ioctl().
Sometimes callers use very large values for e.g. vendor specific media
clear command and calculation can overflow.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This was a temporary debugging thing for sg chaining testing, revert
it now as it has served its purpose.
This reverts commit 563063a808.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix a memory leak in alloc_disk_node(). Don't forget to free 'dkstats' when the allocation of 'part' failed.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
if blktrace program segfault it will not be able
to call BLKTRACETEARDOWN. Now if we run the blktrace
again that would result in a failure to create the
block/<device> debugfs directory.This will result
in blk_remove_root() to be called which will set
blk_tree_root to NULL. But the debugfs block dir
still exist because it contain subdirectory.
Now if we try to fix it using BLKTRACETEARDOWN
it won't work because blk_tree_root is NULL.
Fix the same.
Tested as below
root@qemu-image:/home/kvaneesh/blktrace# ./blktrace -d /dev/hdc
Segmentation fault
root@qemu-image:/home/kvaneesh/blktrace# ./blktrace -d /dev/hdc
BLKTRACESETUP: No such file or directory
Failed to start trace on /dev/hdc
root@qemu-image:/home/kvaneesh/blktrace# ./blktrace -k /dev/hdc
root@qemu-image:/home/kvaneesh/blktrace# ./blktrace -d /dev/hdc
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Added blk_unplug interface, allowing all invocations of unplugs to result
in a generated blktrace UNPLUG.
Signed-off-by: Alan D. Brunelle <Alan.Brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Credit goes to juergen.kadidlo@exasol.com for diagnosing this issue
and supplying the initial patch.
blk_queue_invalidate_tags() must use the proper requeueing paths instead
of open coding the re-add of the request, otherwise we bug out in rq
accounting. Just switch to using blk_requeue_request(), that takes care
of end-tag handling as well and also adds the blktrace REQUEUE notify
event that is also appropriate here.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In theory, if the queue was idle long enough, cfq_idle_class_timer may have
a false (and very long) timeout because jiffies can wrap into the past wrt
->last_end_request.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Jens Axboe