This commit fixes tcp_shift_skb_data() so that it does not shift
SACKed data below snd_una.
This fixes an issue whose symptoms exactly match reports showing
tp->sacked_out going negative since 3.3.0-rc4 (see "WARNING: at
net/ipv4/tcp_input.c:3418" thread on netdev).
Since 2008 (832d11c5cd)
tcp_shift_skb_data() had been shifting SACKed ranges that were below
snd_una. It checked that the *end* of the skb it was about to shift
from was above snd_una, but did not check that the end of the actual
shifted range was above snd_una; this commit adds that check.
Shifting SACKed ranges below snd_una is problematic because for such
ranges tcp_sacktag_one() short-circuits: it does not declare anything
as SACKed and does not increase sacked_out.
Before the fixes in commits cc9a672ee5
and daef52bab1, shifting SACKed ranges
below snd_una happened to work because tcp_shifted_skb() was always
(incorrectly) passing in to tcp_sacktag_one() an skb whose end_seq
tcp_shift_skb_data() had already guaranteed was beyond snd_una. Hence
tcp_sacktag_one() never short-circuited and always increased
tp->sacked_out in this case.
After those two fixes, my testing has verified that shifting SACKed
ranges below snd_una could cause tp->sacked_out to go negative with
the following sequence of events:
(1) tcp_shift_skb_data() sees an skb whose end_seq is beyond snd_una,
then shifts a prefix of that skb that is below snd_una
(2) tcp_shifted_skb() increments the packet count of the
already-SACKed prev sk_buff
(3) tcp_sacktag_one() sees the end of the new SACKed range is below
snd_una, so it short-circuits and doesn't increase tp->sacked_out
(5) tcp_clean_rtx_queue() sees the SACKed skb has been ACKed,
decrements tp->sacked_out by this "inflated" pcount that was
missing a matching increase in tp->sacked_out, and hence
tp->sacked_out underflows to a u32 like 0xFFFFFFFF, which casted
to s32 is negative.
(6) this leads to the warnings seen in the recent "WARNING: at
net/ipv4/tcp_input.c:3418" thread on the netdev list; e.g.:
tcp_input.c:3418 WARN_ON((int)tp->sacked_out < 0);
More generally, I think this bug can be tickled in some cases where
two or more ACKs from the receiver are lost and then a DSACK arrives
that is immediately above an existing SACKed skb in the write queue.
This fix changes tcp_shift_skb_data() to abort this sequence at step
(1) in the scenario above by noticing that the bytes are below snd_una
and not shifting them.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vmxnet3/vmxnet3_drv.c
Small vmxnet3 conflict with header size bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
otherwise source IPv6 address of ICMPV6_MGM_QUERY packet
might be random junk if IPv6 is disabled on interface or
link-local address is not yet ready (DAD).
Signed-off-by: Ulrich Weber <ulrich.weber@sophos.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When associating and particularly when disassociating
there's no need to notify the driver about changes
with multiple calls to bss_info_changed, we should
combine the QoS enabling/disabling into the same call
as otherwise the driver could get confused about QoS
suddenly getting disabled while connected.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to hardcode a subset of the
radiotap header for cooked monitor receive,
we can just reuse the normal monitor mode
radiotap code. This simplifies the code and
extends the information available on cooked
monitor interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds an attribute, NL80211_ATTR_INACTIVITY_TIMEOUT,
to set the inactivity timeout which can be used to remove the
station in AP mode. This can be passed in NL80211_CMD_START_AP
and used by the drivers which have AP MLME in firmware but
don't support get_station() properly. To disable inactivity
timer in userspace, wpa_s for example, there is a new flag,
NL80211_FEATURE_INACTIVITY_TIMER, in nl80211_feature_flags
through which drivers can register their capability to use
the inactivity timeout to free the stations.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RANN, PREP and PERR propagation should happen only if the
dot11MeshForwarding is true. Besides, data frame should not be
forwarded if dot11MeshForwarding is false. This redundant checking
is necessary to avoid the broadcasted ARP breaking the non-forwarding
rule.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers use internal netdev stats member to store part of their
stats, yet advertize ndo_get_stats64() to implement some 64bit fields.
Allow them to use netdev_stats_to_stats64() helper to make the copy of
netdev stats before they compute their 64bit counters.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For A-MPDU rx it makes sense to only process the signal strength once per
aggregate instead of once per subframe. Additonally, some hardware (e.g.
Atheros) only provides valid signal strength information for the last
subframe.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several MAC address comparison functions assume 16 bit alignment for pointers
passed to them. Since the addition of the control_port field, alignment
for the IBSS bssid was off by one, causing a severe performance hit on
architectures without efficient unaligned access (e.g. MIPS).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh peer links are established only if average rssi of the peer
candidate satisfies the threshold. This is not in 802.11s specification
but was requested by David Fulgham, an open80211s user. This is a way to avoid
marginal peer links with stations that are barely within range.
This patch adds a new mesh configuration parameter, mesh_rssi_threshold. This
feature is supported only for hardwares that report signal in dBm.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to Section Y.7.4 Actions on receipt of proactive RANN, an individually
addressed PREQ should be generated towards the neighbor peer mesh STA indicated
in the RANN Sender Address field in the forwarding information.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nlmsg_parse() might return an error, so test its return value before
potential random memory accesses.
Errors introduced in commit 115c9b8192 (rtnetlink: Fix problem with
buffer allocation)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bridge: send proper message_age in config BPDU
added this gem:
bpdu.message_age = (jiffies - root->designated_age)
p->designated_age = jiffies + bpdu->message_age;
Notice how bpdu->message_age is negated when reassigned to
bpdu.message_age. This causes message age to decrease breaking the
STP protocol.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
min age increment needs to round up its min age tick for all
HZ values to guarantee message age is increasing.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since all that include/linux/if_ppp.h does is #include <linux/ppp-ioctl.h>,
this replaces the occurrences of #include <linux/if_ppp.h> with
#include <linux/ppp-ioctl.h>.
It also corrects an error in Documentation/networking/l2tp.txt, where
it referenced include/linux/if_ppp.h as the source of some definitions
that are actually now defined in include/linux/if_pppol2tp.h.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
fs/nfs/nfs4proc.c
Back-merge of the upstream kernel in order to fix a conflict with the
slotid type conversion and implementation id patches...
In tcp_mark_head_lost() we should not attempt to fragment a SACKed skb
to mark the first portion as lost. This is for two primary reasons:
(1) tcp_shifted_skb() coalesces adjacent regions of SACKed skbs. When
doing this, it preserves the sum of their packet counts in order to
reflect the real-world dynamics on the wire. But given that skbs can
have remainders that do not align to MSS boundaries, this packet count
preservation means that for SACKed skbs there is not necessarily a
direct linear relationship between tcp_skb_pcount(skb) and
skb->len. Thus tcp_mark_head_lost()'s previous attempts to fragment
off and mark as lost a prefix of length (packets - oldcnt)*mss from
SACKed skbs were leading to occasional failures of the WARN_ON(len >
skb->len) in tcp_fragment() (which used to be a BUG_ON(); see the
recent "crash in tcp_fragment" thread on netdev).
(2) there is no real point in fragmenting off part of a SACKed skb and
calling tcp_skb_mark_lost() on it, since tcp_skb_mark_lost() is a NOP
for SACKed skbs.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug in the sequence number validation during the initial handshake.
The code did not treat the initial sequence numbers ISS and ISR as read-only and
did not keep state for GSR and GSS as required by the specification. This causes
problems with retransmissions during the initial handshake, causing the
budding connection to be reset.
This patch now treats ISS/ISR as read-only and tracks GSS/GSR as required.
Signed-off-by: Samuel Jero <sj323707@ohio.edu>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This replaces an unjustified BUG_ON(), which could get triggered under normal
conditions: X_calc can be 0 when p > 0. X would in this case be set to the
minimum, s/t_mbi. Its replacement avoids t_ipi = 0 (unbounded sending rate).
Thanks to Jordi, Victor and Xavier who reported this.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.uk>
We are not supposed to force DISCOVERY_STOPPED in inquiry_cache_flush
because we may break the discovery state machine. For instance, during
interleaved discovery, when we are about to start inquiry, the state
machine forcibly goes to DISCOVERY_STOPPED while it should stay in
DISCOVERY_FINDING state.
This problem results in unexpected behaviors such as sending two
mgmt_discovering events to userspace (when only one event is expected)
and Stop Discovery failures.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When powering on we need to apply whatever name has been set through
mgmt_set_local_name. The appropriate place for this is mgmt_powered()
and not hci_setup() since this needs to be applied also if the HCI init
sequence was already completed but the adapter was still "powered off"
from a mgmt perspective due the the HCI_AUTO_OFF still being set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This flag is of no use right now and is in fact harmful in that it
prevents the HCI_MGMT flag to be set for any controllers that may need
it after the first one that bluetoothd takes into use (the flag is
cleared for the first controller so any subsequent ones through the same
bluetoothd mgmt socket never get the HCI_MGMT flag set).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
NFSv4.0 clients must send endpoint information for their callback
service to NFSv4.0 servers during their first contact with a server.
Traditionally on Linux, user space provides the callback endpoint IP
address via the "clientaddr=" mount option.
During an NFSv4 migration event, it is possible that an FSID may be
migrated to a destination server that is accessible via a different
source IP address than the source server was. The client must update
callback endpoint information on the destination server so that it can
maintain leases and allow delegation.
Without a new "clientaddr=" option from user space, however, the
kernel itself must construct an appropriate IP address for the
callback update. Provide an API in the RPC client for upper layer
RPC consumers to acquire a source address for a remote.
The mechanism used by the mount.nfs command is copied: set up a
connected UDP socket to the designated remote, then scrape the source
address off the socket. We are careful to select the correct network
namespace when setting up the temporary UDP socket.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When the cl_xprt field is updated, the cl_server field will also have
to change. Since the contents of cl_server follow the remote endpoint
of cl_xprt, just move that field to the rpc_xprt.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[ cel: simplify check_gss_callback_principal(), whitespace changes ]
[ cel: forward ported to 3.4 ]
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
A migration event will replace the rpc_xprt used by an rpc_clnt. To
ensure this can be done safely, all references to cl_xprt must now use
a form of rcu_dereference().
Special care is taken with rpc_peeraddr2str(), which returns a pointer
to memory whose lifetime is the same as the rpc_xprt.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[ cel: fix lockdep splats and layering violations ]
[ cel: forward ported to 3.4 ]
[ cel: remove rpc_max_reqs(), add rpc_net_ns() ]
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The index is part of the command header and not its parameters so it
makes sense to distinguish this from the invalid parameters error.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Error codes in the command status should always be from the set of
values defined for mgmt and never e.g. POSIX error codes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
When doing reset HCI_PENDING_CLASS is one of the flags that should be
cleared (since it's used for a pending HCI command and a reset clear all
pending commands).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Conflicts:
drivers/net/ethernet/broadcom/tg3.c
Conflicts in the statistics regression bug fix from 'net',
but happily Matt Carlson originally posted the fix against
'net-next' so I used that to resolve this.
Signed-off-by: David S. Miller <davem@davemloft.net>
The MGMT and SMP timeout constants are always used in form of jiffies. So
just include the conversion from msecs in the define itself. This has the
advantage of making the code where the timeout is used more readable.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The L2CAP timeout constants are always used in form of jiffies. So just
include the conversion from msecs in the define itself. This has the
advantage of making the code where the timeout is used more readable.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch moves the command length information into the command handler
table allowing the removal of length checks from the handler functions
and doing the check in a single place before calling the handler
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
By moving the command handlers into a table (the index being equal to
the opcode) the lookup is made a bit more efficient. Having a struct to
describe each handler also paves the way to add more meta-data for each
handler, e.g. the minimum message size for the command and allow
handling of common tasks like this in a centralized place.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The read_controller_info is typically the first command that user space
sends when taking a controller into use. This is also the reason why
this command has been used as the trigger to set the HCI_MGMT flag.
However, when not running the user-space daemon and using command line
tools it is possible that read_controller_info is not the first
controller specific command. This patch moves the HCI_MGMT
initialization to a generic place where it will be set for whatever
happens to be the first mgmt command targetting a specific controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Almost all mgmt commands need to lookup a struct hci_dev based on the
index received within the mgmt headers. It makese therefore sense to
look this up in a single place and then just pass the hdev pointer to
each command handler function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Some CSR controllers will generate a spontaneous reset during init and
just eat up any pending command without sending a command complete for
it. This patch solves the issue by just resending whatever was the last
sent command. hci_send_cmd is not used since we need to bypass all other
commands in the send queue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch add an extra check for BR/EDR and LE-Only discovery.
This way, we are able to return error immediately if the discovery
type requested is not supported by the device.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add VF spoof check to IFLA policy. The original patch I submitted to
add the spoof checking feature to rtnl failed to add the proper policy
rule that identifies the data type and len. This patch corrects that
oversight. No bugs have been reported against this but it may cause
some problem for the netlink message parsing that uses the policy
table.
CC: stable@vger.kernel.org
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The set_le() function was missing hci_dev locking which is e.g. critical
for the mgmt pending command adding/removing.
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This renames the IEEE80211_TX_CTL_POLL_RESPONSE
TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also
uses it for non-bufferable MMPDUs (all MMPDUs but
deauth, disassoc and action frames.)
Previously, mac80211 would let the MMPDU through
but not set the flag so drivers supporting some
hardware aids for avoiding the PS races would
then reject the frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The association sequence looks (roughly) like
this now:
* set BSSID
* set station to EXIST state
* send auth
* set station to AUTH state
* send assoc
* set station to ASSOC state
* set BSS info to associated
In contrast, the deauth/disassoc sequence is
the other way around:
* clear BSSID/BSS info state
* remove station
* send deauth/disassoc
(in some cases the last two steps are reversed.)
This patch encodes the entire sequence in the
ieee80211_set_disassoc() function and changes
it to be like this, for good measure with an
explicit flush:
* send deauth/disassoc
* flush
* remove station
* clear BSSID/BSS info state
At least iwlwifi gets confused with the other
sequence in P2P mode and complains that it
wasn't able to flush the queues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ieee80211_set_disassoc() is called with the
tx argument set to true, it will send DelBA out
to the peer. This isn't useful or necessary in a
few cases where we do it today, those being when
we lost the connection or when the supplicant
explicitly asked us to not tell the AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of calling cfg80211 in ieee80211_send_deauth_disassoc()
pass out the frame and call it from the caller. That saves the
SKB allocation if we don't actually want to send the frame and
enables us to make the ordering smarter in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SMP is not a kernel module, it is part of Bluetooth Core (as already
described in lines above).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Optimizes routines that send payload messages so that they no longer
update the "originating node" and "originating port" fields of the
outgoing message header template, since these fields are initialized
when the sending port is created and never change thereafter. Also
optimizes the routine which updates the message header template when
a connection to a port is established, for the same reason.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes code that updated the "previous node" field of an out-going
message over TIPC's links. Such updating is unnecessary since the
removal of the prototype multi-cluster capability means that all
outgoing messages are generated locally and already have this field
populated correctly.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Converts a non-trivial routine from inline to non-inline form
to avoid bloating the TIPC code base with 6 copies of its body.
This change is essentially cosmetic, and doesn't change existing
TIPC behavior.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Last param of mgmt_device_connected is of pointer type, so use NULL
instead of 0 for it. This fix following sparse warning:
CHECK net/bluetooth/hci_event.c
net/bluetooth/hci_event.c:3262:74: warning: Using plain integer as NULL pointer
Signed-off-by: Szymon Janc <szymon@janc.net.pl>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
According to last discussion on IRC, if an interleaved discovery is
issued, but the device is not dual mode, we should return error
instead of performing a regular BR/EDR or LE-only discovery.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fixed channel mask needs to be stored to decide whether to
use A2MP for example. So far save only one relevant byte which
keeps all information we need.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
"count" is type int so the cast to __u16 truncates the high bits away
and triggers a Smatch static checker warning. It looks like a high
value of count could cause a forever loop, but I didn't follow it
through to see if count is capped somewhere.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
sk_buffs should be freed using kfree_skb().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When tcp_shifted_skb() shifts bytes from the skb that is currently
pointed to by 'highest_sack' then the increment of
TCP_SKB_CB(skb)->seq implicitly advances tcp_highest_sack_seq(). This
implicit advancement, combined with the recent fix to pass the correct
SACKed range into tcp_sacktag_one(), caused tcp_sacktag_one() to think
that the newly SACKed range was before the tcp_highest_sack_seq(),
leading to a call to tcp_update_reordering() with a degree of
reordering matching the size of the newly SACKed range (typically just
1 packet, which is a NOP, but potentially larger).
This commit fixes this by simply calling tcp_sacktag_one() before the
TCP_SKB_CB(skb)->seq advancement that can advance our notion of the
highest SACKed sequence.
Correspondingly, we can simplify the code a little now that
tcp_shifted_skb() should update the lost_cnt_hint in all cases where
skb == tp->lost_skb_hint.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The major features of this series are:
- making RCU more aggressive about entering dyntick-idle mode in order to
improve energy efficiency
- converting a few more call_rcu()s to kfree_rcu()s
- applying a number of rcutree fixes and cleanups to rcutiny
- removing CONFIG_SMP #ifdefs from treercu
- allowing RCU CPU stall times to be set via sysfs
- adding CPU-stall capability to rcutorture
- adding more RCU-abuse diagnostics
- updating documentation
- fixing yet more issues located by the still-ongoing top-to-bottom
inspection of RCU, this time with a special focus on the
CPU-hotplug code path.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes the code to use the proper LMP_HOST_SSP define instead
of magic values and thereby makes the code more readable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Previously the write_le_enable would trigger a read_host_features
command but since we have access to the value LE support was set to we
can simply just clear or set the bit in hdev->host_features. This also
removes a second unnecessary read_host_features command from the device
initialization procedure since LE is only enabled after the first
read_host_features command completes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
If the local host features indicate that LE is already in the state that
is desired there's no point in sending the HCI command to try to change
the setting.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
That's a lot longer than open-coding it and
doesn't really add value, so just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comment for sta_info_flush() states
"Returns the number of removed STA entries"
but that isn't actually true. Consequently,
the warning when a station is still around
on interface removal can never trigger and
this delayed finding the timer issue the
previous patch fixed. Fix the return value
here to make that warning useful again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When removing an interface while it is in the
process of authenticating or associating, we
leak the auth_data or assoc_data, and leave
the timer pending. The timer then crashes the
system when it fires as its data is gone.
Fix this by explicitly deleting all the data
when the interface is removed. This uncovered
another bug -- this problem should have been
detected by the sta_info_flush() warning but
that function doesn't ever return non-zero,
I'll fix that in a separate patch.
Reported-by: Hieu Nguyen <hieux.c.nguyen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use interface data from sta instead of invalid pointer
to list head in calls to drv_sta_state.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad reports that if a scan finishes in the
middle of processing associated (however it
happens), the interface can go idle. This is
because we set assoc_data to NULL before we
set associated. Change the order so any idle
check will find either one of them.
Doing this requires duplicating the TX sync
processing, but I already have a patch to
delete that completely and will submit that
as soon as my driver changes to no longer
require it are submitted.
Reported-by: Eliad Peller <eliad@wizery.com>
Tested-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some files implicitly get this via mesh.h
which itself doesn't need it, so move the
inclusion into the right files. Some other
files don't need it at all but include it,
so remove it from there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_restart_sta_timer() takes care for enqueueing
monitor_work if needed, so no need to do it again.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices that monitor the connection in the hw don't need
the monitor work in the driver.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, wait queue, used for polling of RPC pipe changes from user-space,
is a part of RPC pipe. But the pipe data itself can be released on NFS umount
prior to dentry-inode pair, connected to it (is case of this pair is open by
some process).
This is not a problem for almost all pipe users, because all PipeFS file
operations checks pipe reference prior to using it.
Except evenfd. This thing registers itself with "poll" file operation and thus
has a reference to pipe wait queue. This leads to oopses on destroying eventfd
after NFS umount (like rpc_idmapd do) since not pipe data left to the point
already.
The solution is to wait queue from pipe data to internal RPC inode data. This
looks more logical, because this wiat queue used only for user-space processes,
which already holds inode reference.
Note: upcalls have to get pipe->dentry prior to dereferecing wait queue to make
sure, that mount point won't disappear from underneath us.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
There are 2 tightly bound objects: pipe data (created for kernel needs, has
reference to dentry, which depends on PipeFS mount/umount) and PipeFS
dentry/inode pair (created on mount for user-space needs). They both
independently may have or have not a valid reference to each other.
This means, that we have to make sure, that pipe->dentry reference is valid on
upcalls, and dentry->pipe reference is valid on downcalls. The latter check is
absent - my fault.
IOW, PipeFS dentry can be opened by some process (rpc.idmapd for example), but
it's pipe data can belong to NFS mount, which was unmounted already and thus
pipe data was destroyed.
To fix this, pipe reference have to be set to NULL on rpc_unlink() and checked
on PipeFS file operations instead of pipe->dentry check.
Note: PipeFS "poll" file operation will be updated in next patch, because it's
logic is more complicated.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
v3:
1) Lookup for client is performed from the beginning of the list on each PipeFS
event handling operation.
Lockdep is sad otherwise, because inode mutex is taken on PipeFS dentry
creation, which can be called on mount notification, where this per-net client
lock is taken on clients list walk.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
u8/__u8/u32/etc should be used in the kernel instead of stdint.h types.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) ICMP sockets leave err uninitialized but we try to return it for the
unsupported MSG_OOB case, reported by Dave Jones.
2) Add new Zaurus device ID entries, from Dave Jones.
3) Pointer calculation in hso driver memset is wrong, from Dan
Carpenter.
4) ks8851_probe() checks unsigned value as negative, fix also from Dan
Carpenter.
5) Fix crashes in atl1c driver due to TX queue handling, from Eric
Dumazet. I anticipate some TX side locking fixes coming in the near
future for this driver as well.
6) The inline directive fix in Bluetooth which was breaking the build
only with very new versions of GCC, from Johan Hedberg.
7) Fix crashes in the ATP CLIP code due to ARP cleanups this merge
window, reported by Meelis Roos and fixed by Eric Dumazet.
8) JME driver doesn't flush RX FIFO correctly, from Guo-Fu Tseng.
9) Some ip6_route_output() callers test the return value for NULL, but
this never happens as the convention is to return a dst entry with
dst->error set. Fixes from RonQing Li.
10) Logitech Harmony 900 should be handled by zaurus driver not
cdc_ether, update white lists and black lists accordingly. From
Scott Talbert.
11) Receiving from certain kinds of devices there won't be a MAC header,
so there is no MAC header to fixup in the IPSEC code, and if we try
to do it we'll crash. Fix from Eric Dumazet.
12) Port type array indexing off-by-one in mlx4 driver, fix from Yevgeny
Petrilin.
13) Fix regression in link-down handling in davinci_emac which causes
all RX descriptors to be freed up and therefore RX to wedge
completely, from Christian Riesch.
14) It took two attempts, but ctnetlink soft lockups seem to be
cured now, from Pablo Neira Ayuso.
15) Endianness bug fix in ENIC driver, from Santosh Nayak.
16) The long ago conversion of the PPP fragmentation code over to
abstracted SKB list handling wasn't perfect, once we get an
out of sequence SKB we don't flush the rest of them like we
should. From Ben McKeegan.
17) Fix regression of ->ip_summed initialization in sfc driver.
From Ben Hutchings.
18) Bluetooth timeout mistakenly using msecs instead of jiffies,
from Andrzej Kaczmarek.
19) Using _sync variant of work cancellation results in deadlocks,
use the non _sync variants instead. From Andre Guedes.
20) Bluetooth rfcomm code had reference counting problems leading
to crashes, fix from Octavian Purdila.
21) The conversion of netem over to classful qdisc handling added
two bugs to netem_dequeue(), fixes from Eric Dumazet.
22) Missing pci_iounmap() in ATM Solos driver. Fix from Julia Lawall.
23) b44_pci_exit() should not have __exit tag since it's invoked from
non-__exit code. From Nikola Pajkovsky.
24) The conversion of the neighbour hash tables over to RCU added a
race, fixed here by adding the necessary reread of tbl->nht, fix
from Michel Machado.
25) When we added VF (virtual function) attributes for network device
dumps, this potentially bloats up the size of the dump of one
network device such that the dump size is too large for the buffer
allocated by properly written netlink applications.
In particular, if you add 255 VFs to a network device, parts of
GLIBC stop working.
To fix this, we add an attribute that is used to turn on these
extended portions of the network device dump. Sophisticaed
applications like 'ip' that want to see this stuff will be changed
to set the attribute, whereas things like GLIBC that don't care
about VFs simply will not, and therefore won't be busted by the
mere presence of VFs on a network device.
Thanks to the tireless work of Greg Rose on this fix.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
sfc: Fix assignment of ip_summed for pre-allocated skbs
ppp: fix 'ppp_mp_reconstruct bad seq' errors
enic: Fix endianness bug.
gre: fix spelling in comments
netfilter: ctnetlink: fix soft lockup when netlink adds new entries (v2)
Revert "netfilter: ctnetlink: fix soft lockup when netlink adds new entries"
davinci_emac: Do not free all rx dma descriptors during init
mlx4_core: Fixing array indexes when setting port types
phy: IC+101G and PHY_HAS_INTERRUPT flag
netdev/phy/icplus: Correct broken phy_init code
ipsec: be careful of non existing mac headers
Move Logitech Harmony 900 from cdc_ether to zaurus
hso: memsetting wrong data in hso_get_count()
netfilter: ip6_route_output() never returns NULL.
ethernet/broadcom: ip6_route_output() never returns NULL.
ipv6: ip6_route_output() never returns NULL.
jme: Fix FIFO flush issue
atm: clip: remove clip_tbl
ipv4: ping: Fix recvmsg MSG_OOB error handling.
rtnetlink: Fix problem with buffer allocation
...
This patch adds CTA_MARK_MASK which, together with CTA_MARK, allows
you to selectively send conntrack entries to user-space by
returning those that match mark & mask.
With this, we can save cycles in the building and the parsing of
the entries that may be later on filtered out in user-space by using
the ctmark & mask.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows you to pass a data pointer that can be
accessed from the dump callback.
Netfilter is going to use this patch to provide filtered dumps
to user-space. This is specifically interesting in ctnetlink that
may handle lots of conntrack entries. We can save precious
cycles by skipping the conversion to TLV format of conntrack
entries that are not interesting for user-space.
More specifically, ctnetlink will include one operation to allow
to filter the dumping of conntrack entries by ctmark values.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davem considers that the argument list of this interface is getting
out of control. This patch tries to address this issue following
his proposal:
struct netlink_dump_control c = { .dump = dump, .done = done, ... };
netlink_dump_start(..., &c);
Suggested by David S. Miller.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We expected 0 if module doesn't exist, which is no longer the case
(42046e2e45,
netfilter: x_tables: return -ENOENT for non-existant matches/targets).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The original spelling and bad word choice makes these comments hard to read.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes all references to the global variable that records whether
TIPC is running in "single node" mode or "network" mode, since this
information can be easily deduced from the global variable that
records TIPC's network address. (i.e. a non-zero network address
means that TIPC is running in network mode.)
The changes made update most existing mode-based checks to use the
network address global variable. A few checks that are no longer
needed are removed entirely, along with any associated code lying on
non-executable control paths.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes all references to TIPC's "not running" mode, since the
removal of support for the native API means that there is no longer
any way to interact with TIPC if it has not been initialized.
The changes made consist of removing mode-based checks that are no
longer needed, along with any associated code lying on non-executable
control paths.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Restores name table translation using a non-zero domain that is
"out of scope", which was broken by an earlier commit
(5d9c54c1e9). Comments have now been
added to the name table translation routine to make it clear that
there are actually three possible outcomes to a translation request
(found/not found/deferred), rather than just two (found/not found).
Note that a straightforward revert of the earlier commit is not
possible, as other changes to the name table translation logic
have occurred since the incorrect optimization was made.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Optimizes processing done when contact with a neighboring node is
established to avoid recording the current state of outgoing broadcast
messages if the neighboring node isn't a valid broadcast link destination,
since this state information isn't needed for such nodes.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates a block of comments that describe how routing table updates
are to be handled. These comments no longer apply following the removal
of TIPC's prototype multi-cluster support.
Note that these changes are essentially cosmetic in nature, and have
no impact on the actual operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of two inlined routines that simply call existing sk_buff
manipulation routines, since there is no longer any extra processing
done by the helper routines.
Note that these changes are essentially cosmetic in nature, and have
no impact on the actual operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Relocates information about the size of TIPC's node table index and
its associated hash function, since only node subsystem routines need
to have access to this information.
Note that these changes are essentially cosmetic in nature, and have
no impact on the actual operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Simplifies a comparison operation to eliminate a useless test that
checks if an unsigned value is less than zero.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This "shortform" is actually longer than typing out what it is really
trying to do, and just makes reading the code more difficult, so
lets simply shoot it in the head.
In the case of log.c - the comparison is on a u32, so we can drop the
check for < 0 at the same time.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds a new check to TIPC's name table logic to reject any attempt to
create a new name publication that is identical to an existing one.
(Such an attempt will never happen under normal circumstances, but
could arise if another network node malfunctions and issues a duplicate
name publication message.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Streamlines the logic that prevents an application from binding a
reserved TIPC name type to a port by moving the check to the code
that handles a socket bind() operation. This allows internal TIPC
subsystems to bind a reserved name without having to set an atomic
flag to gain permission to use such a name. (This simplification is
now possible due to the elimination of support for TIPC's native API.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates a check in the processing of TIPC messages arriving from
off node that ensures the message is destined for this node, since this
check duplicates an earlier check. (The check would be necessary if TIPC
needed to be able to route incoming messages to another node, but the
elimination of multi-cluster support means that this never happens and
all incoming messages are consumed by the receiving node.)
Note: This change involves the elimination of a single "if" statement
with a large "then" clause; consequently, a significant number of lines
end up getting re-indented. In addition, a simple message header access
routine that is no longer referenced is eliminated. However, the only
functional change is the elimination of the single check described above.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Utilizes the new "node signature" field in neighbor discovery messages
to ensure that all links TIPC associates with a given <Z.C.N> network
address belong to the same neighboring node. (Previously, TIPC could not
tell if link setup requests arriving on different interfaces were from
the same node or from two different nodes that has mistakenly been assigned
the same network address.)
The revised algorithm for detecting a duplicate node considers both the
node signature and the network interface adddress specified in a request
message when deciding how to respond to a link setup request. This prevents
false alarms that might otherwise arise during normal network operation
under the following scenarios:
a) A neighboring node reboots. (The node's signature changes, but the
network interface address remains unchanged.)
b) A neighboring node's network interface is replaced. (The node's signature
remains unchanged, but the network interface address changes.)
c) A neighboring node is completely replaced. (The node's signature and
network interface address both change.)
The algorithm also handles cases in which a node reboots and re-establishes
its links to TIPC (or begins re-establishing those links) before TIPC
detects that it is using a new node signature. In such cases of "delayed
rediscovery" TIPC simply accepts the new signature without disrupting
communication that is already underway over the links.
Thanks to Laser [gotolaser@gmail.com] for his contributions to the
development of this enhancement.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds support for the new "node signature" in neighbor discovery messages,
which is a 16 bit identifier chosen randomly when TIPC is initialized.
This field makes it possible for nodes receiving a neighbor discovery
message to detect if multiple neighboring nodes are using the same network
address (i.e. <Z.C.N>), even when the messages are arriving on different
interfaces.
This first phase of node signature support creates the signature,
incorporates it into outgoing neighbor discovery messages, and tracks
the signature used by valid neighbors. An upcoming patch builds on this
foundation to implement the improved duplicate neighbor detection checking.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The same sequence sending L2CAP Connection Request was used in several
places. Using subroutine makes those places easy to read.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Mark request status as done for Read Local Version HCI command. In AMP
initialization this HCI command is the last and needs to be completed.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With Bluetooth 1.1 controllers the last command in the HCI init sequence
will be a write_local_name, however there was no callback to indicate
init request completion in this case. This patch fixes the issue by
adding the necessary callback to the write_local_name_complete handler.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcell Zambo and Janos Farago noticed and reported that when
new conntrack entries are added via netlink and the conntrack table
gets full, soft lockup happens. This is because the nf_conntrack_lock
is held while nf_conntrack_alloc is called, which is in turn wants
to lock nf_conntrack_lock while evicting entries from the full table.
The patch fixes the soft lockup with limiting the holding of the
nf_conntrack_lock to the minimum, where it's absolutely required.
It required to extend (and thus change) nf_conntrack_hash_insert
so that it makes sure conntrack and ctnetlink do not add the same entry
twice to the conntrack table.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This reverts commit af14cca162.
This patch contains a race condition between packets and ctnetlink
in the conntrack addition. A new patch to fix this issue follows up.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This flag requests that network devices pass all
received frames up the stack, even ones with errors
such as invalid FCS (frame check sum). This will
allow sniffers to see bad packets and perhaps
give the user some idea how to fix the problem.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is useful for testing RX handling of frames with bad
CRCs.
Requires driver support to actually put the packet on the
wire properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When set on hardware that supports the feature,
this causes the Ethernet FCS to be appended
to the end of the skb.
Useful for sniffing packets.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
So here's a boot tested patch on top of Jason's series that does
all the cleanups I talked about and turns jump labels into a
more intuitive to use facility. It should also address the
various misconceptions and confusions that surround jump labels.
Typical usage scenarios:
#include <linux/static_key.h>
struct static_key key = STATIC_KEY_INIT_TRUE;
if (static_key_false(&key))
do unlikely code
else
do likely code
Or:
if (static_key_true(&key))
do likely code
else
do unlikely code
The static key is modified via:
static_key_slow_inc(&key);
...
static_key_slow_dec(&key);
The 'slow' prefix makes it abundantly clear that this is an
expensive operation.
I've updated all in-kernel code to use this everywhere. Note
that I (intentionally) have not pushed through the rename
blindly through to the lowest levels: the actual jump-label
patching arch facility should be named like that, so we want to
decouple jump labels from the static-key facility a bit.
On non-jump-label enabled architectures static keys default to
likely()/unlikely() branches.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jason Baron <jbaron@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: a.p.zijlstra@chello.nl
Cc: mathieu.desnoyers@efficios.com
Cc: davem@davemloft.net
Cc: ddaney.cavm@gmail.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20120222085809.GA26397@elte.hu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since the clear_uuids operation doesn't send an immediate HCI command
but just sets off a timer to wait for subsequent add_uuid calls it
doesn't make sense to wait until the timer fires off to send the
response. Instead send the response immediately.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
All mgmt commands that may fire off a hci_write_class_of_device command
should wait for the completion of the HCI command before sending a
response to user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a flag to track pending changes to the class of device.
This is needed since we cannot cleanly handle multiple simultaneous
commands and need to return a "busy" error status in the mgmt commands
that might trigger a class change.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niccolo Belli reported ipsec crashes in case we handle a frame without
mac header (atm in his case)
Before copying mac header, better make sure it is present.
Bugzilla reference: https://bugzilla.kernel.org/show_bug.cgi?id=42809
Reported-by: Niccolò Belli <darkbasic@linuxsystems.it>
Tested-by: Niccolò Belli <darkbasic@linuxsystems.it>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the Device Connected events to match the latest API
by adding a flags parameter to them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
We also need to send a proper response when clearing UUIDs. This patch
adds fixes the missing response for this use case.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Since we can now add UUIDs when powered off we don't really need to
always use the service cache to avoid large bursts of HCI commands.
Instead, the only important use case is when we're already powered and
user space starts to initialize itself. This can be easiest detected by
a "clear UUIDs" operation which is where this patch moves the service
cache setting.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The Add/Remove UUID commands should return the device class instead of
an empty parameter list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
If we're powered but still have the HCI_AUTO_OFF flag set the
update_eir and update_class functions should not do anything.
Additionally these functions need to be called when the flag is finally
cleared through set_powered or when powering on for real.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
If controller is reset during the discovery procedure, Start Discovery
command stops working. This can be easily reproduced by running
"hciconfig hci0 reset" while discovering devices, for instance.
We should force discovery state to DISCOVERY_STOPPED in case we receive
a reset command complete event. Otherwise we may stuck in one of the
active discovery states (DISCOVERY_INQUIRY, DISCOVERY_LE_SCAN and
DISCOVERY_RESOLVING) and subsequent Start Discovery commands will simply
fail.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch fixes the count parameter in the Get Connections reply
message. We cannot know the right number until iterating through all
connections so set the parameter value only after the loop.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Simplify code so that we do not need to check whether socket is locked.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Change sk lock to chan lock in l2cap core and move sk locks
to l2cap sock code. bh_locks were used because of being RCU
critical section. When needed use explicit socket locks.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add unlocked L2CAP channel add function. Unlocked version will
be used in later patches.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch makes sure that legacy pairing vs SSP infomation gets
properly propageted to the device_found events in the form of the legacy
pairing flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
According to the latest mgmt API there's a flags field instead of a
separate confirm_name paramter.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an error return when not powered and cleans up/simpifies
the function logic in the same go.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds missing powered checks to pair_device,
cancel_pair_device, add_remote_oob_data and remove_remote_oob_data.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes it possible to set the class when powered off. When
powering on the right class of device value will be automatically
writen to the controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
These functions should just silently fail when we're not powered on
instead of trying to send HCI commands.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The return parameters for Set Device Class should consist of the new
class value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
We should assume a value of 0 for the device class when powered off.
The appropriate place to do this is in hci_dev_do_close().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The short name is part of the Read Controller Info response and should
be appropriately filled in based on the value of hdev->short_name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Since we can't reliably track the short name changes just assume that we
had a change whenever there's a pending mgmt command. In the worst case
we just get one unnecessary name_changed signal.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes it possible to set the local name before powering on
the device. The name will be applied using the hci_write_local_name
command once the device gets powered on.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The local name should only be updated as a consequence of a
hci_read_local_name if we are in the HCI_SETUP state. In all other
scenarios it should only be updated through hci_write_local_name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
It's possible to provide a short name through the mgmt interface and
this name can be used for EIR generation when the full name doesn't fit
there. This patch adds the preliminary tracking of the provided short
name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Currently there are no events to other management sockets if the class of
device got changed. So make sure they are sent.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The current handling of the discoverable timeout was missing the proper
handling of the timeout when the mode was already set. Now the command
can be used to expire or retrigger the timeout.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add one extra sanity check to ensure that the supplied timeout value is
actually valid in this context.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Whenever we update the local device name the EIR data also needs to be
updated to reflect this. The update_eir() function in mgmt.c depends on
hdev->dev_name to be up to date so the patch also makes sure that the
mgmt function is called from hci_event.c after the update has happened.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
When powering off we should assume that the EIR data isn't valid
anymore. This patch makes sure it gets cleared in hci_dev_do_close and
thereby ensures that a correct new EIR is recreated when powering on
again.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements support for the Set LE mgmt command. Now, in
addition to the enable_le module parameter user space needs to send an
explicit Enable LE command to enable LE support.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The test for SSP support needs to be earlier in the set_ssp function so
that we return an error when SSP is not supported even when the device
is powered off.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The control channel can be also monitored, so include timestamps here
as well. And make sure management events get their timestamp when they
are created.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some controllers preserve their EIR data even after a reset so we need
to explicitly clear this during the device setup procedure.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The hdev->eir buffer needs to be cleared when clearing the EIR data.
Otherwise subsequent attempts at setting the EIR to something valid
again may fail because the code thinks that the EIR hasn't changed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes setting the EIR properly when the SSP flag has been set
when powered off (in such a case there is no pending Set_SSP command).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
In this case we need to use braces in both branches.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
WARNING: Statements terminations use 1 semicolon
+ return err;;
WARNING: space prohibited between function name and open parenthesis '('
+ err = cmd_status (sk, index, MGMT_OP_CONFIRM_NAME,
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch makes it possible to enable SSP through mgmt even when
powered off. The setting will then get automatically actiated when
powering on.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The kernel has no need to track the hci_read_ssp_mode command since it
has the hci_sent_cmd_data function to check what value was set when
hci_write_ssp_mode completes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes it possible to change the Link Security setting while
powered off and have it automatically enabled when powering on a device.
To track the desired state once powered on a new HCI_LINK_SECURITY flag
is added.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Use locked and unlocked versions to help removing socket
locks from l2cap core functions.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Split to locked and unlocked versions of l2cap_state_change helping
to remove socket locks from l2cap code.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Channel lock will be used to lock L2CAP channels which are locked
currently by socket locks.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Usage of RCU list looks not reasonalbe for a number of reasons:
our code sleep and we had to use socket spinlocks. Most parts
of code are updaters thus there is little sense to use RCU.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
ip6_route_output() never returns NULL, so it is wrong to
check if the return value is NULL.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_output() never returns NULL, so it is wrong to
check if the return value is NULL.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AP/GO mode API isn't very clearly defined, it
has "set beacon" and "new beacon" etc.
Modify the API to the following:
* start AP -- all settings
* change beacon -- new beacon data
* stop AP -- stop AP mode operation
This also reflects in the nl80211 API, rename
the commands there correspondingly (but keep
the old names for compatibility.)
Overall, this makes it much clearer what's going
on in the API.
Kalle developed the ath6kl changes, I created
the rest of the patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Piergiorgio Beruto expressed the need to fetch size of first datagram in
queue for AF_UNIX sockets and suggested a patch against SIOCINQ ioctl.
I suggested instead to implement MSG_TRUNC support as a recv() input
flag, as already done for RAW, UDP & NETLINK sockets.
len = recv(fd, &byte, 1, MSG_PEEK | MSG_TRUNC);
MSG_TRUNC asks recv() to return the real length of the packet, even when
is was longer than the passed buffer.
There is risk that a userland application used MSG_TRUNC by accident
(since it had no effect on af_unix sockets) and this might break after
this patch.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
CC: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_mac_addr() for .ndo_set_mac_address, remove
lowpan_set_address since it do currently the same as
eth_mac_addr(). Additional advantage: eth_mac_addr() already
checks if the given address is valid
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 32092ecf06 (atm: clip: Use device neigh support on top of
"arp_tbl".) introduced a bug since clip_tbl is zeroed : Crash occurs in
__neigh_for_each_release()
idle_timer_check() must use instead arp_tbl and neigh_check_cb() should
ignore non clip neighbours.
Idea from David Miller.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't return an uninitialized variable as the error, return
-EOPNOTSUPP instead.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a new netlink attribute type IFLA_EXT_MASK. The mask
is a 32 bit value that can be used to indicate to the kernel that
certain extended ifinfo values are requested by the user application.
At this time the only mask value defined is RTEXT_FILTER_VF to
indicate that the user wants the ifinfo dump to send information
about the VFs belonging to the interface.
This patch fixes a bug in which certain applications do not have
large enough buffers to accommodate the extra information returned
by the kernel with large numbers of SR-IOV virtual functions.
Those applications will not send the new netlink attribute with
the interface info dump request netlink messages so they will
not get unexpectedly large request buffers returned by the kernel.
Modifies the rtnl_calcit function to traverse the list of net
devices and compute the minimum buffer size that can hold the
info dumps of all matching devices based upon the filter passed
in via the new netlink attribute filter mask. If no filter
mask is sent then the buffer allocation defaults to NLMSG_GOODSIZE.
With this change it is possible to add yet to be defined netlink
attributes to the dump request which should make it fairly extensible
in the future.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the fixed race condition happens:
1. While function neigh_periodic_work scans the neighbor hash table
pointed by field tbl->nht, it unlocks and locks tbl->lock between
buckets in order to call cond_resched.
2. Assume that function neigh_periodic_work calls cond_resched, that is,
the lock tbl->lock is available, and function neigh_hash_grow runs.
3. Once function neigh_hash_grow finishes, and RCU calls
neigh_hash_free_rcu, the original struct neigh_hash_table that function
neigh_periodic_work was using doesn't exist anymore.
4. Once back at neigh_periodic_work, whenever the old struct
neigh_hash_table is accessed, things can go badly.
Signed-off-by: Michel Machado <michel@digirati.com.br>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same here -- we can protect the sk_peek_off manipulations with
the unix_sk->readlock mutex.
The peeking of data from a stream socket is done in the datagram style,
i.e. even if there's enough room for more data in the user buffer, only
the head skb's data is copied in there. This feature is preserved when
peeking data from a given offset -- the data is read till the nearest
skb's boundary.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sk_peek_off manipulations are protected with the unix_sk->readlock mutex.
This mutex is enough since all we need is to syncronize setting the offset
vs reading the queue head. The latter is fully covered with the mentioned lock.
The recently added __skb_recv_datagram's offset is used to pick the skb to
read the data from.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one specifies where to start MSG_PEEK-ing queue data from. When
set to negative value means that MSG_PEEK works as ususally -- peeks
from the head of the queue always.
When some bytes are peeked from queue and the peeking offset is non
negative it is moved forward so that the next peek will return next
portion of data.
When non-peeking recvmsg occurs and the peeking offset is non negative
is is moved backward so that the next peek will still peek the proper
data (i.e. the one that would have been picked if there were no non
peeking recv in between).
The offset is set using per-proto opteration to let the protocol handle
the locking issues and to check whether the peeking offset feature is
supported by the protocol the socket belongs to.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one is only considered for MSG_PEEK flag and the value pointed by
it specifies where to start peeking bytes from. If the offset happens to
point into the middle of the returned skb, the offset within this skb is
put back to this very argument.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes lines shorter and simplifies further patching.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nothing needs to be done for monitor/AP_VLAN mode on calling
ieee80211_bss_info_change_notify -> drv_bss_info_changed with the change
flag 'BSS_CHANGED_IDLE'. 'wl1271' seems to use BSS_CHANGED_IDLE only for
STA and IBSS mode. further the non-idle state of the monitor mode is
taken care by the 'count' variable which counts non-idle interfaces.
ieee80211_idle_off(local, "in use") will be called.
this fixes the following WARNING when we have initially STA mode
(network manager running) and not associated, and change it to monitor
mode with network manager disabled and bringing up the monitor mode.
this changes the idle state from 'true' (STA unassociated) to 'false'
(MONITOR mode)
exposed by the commit 405385f8ce
"mac80211: set bss_conf.idle when vif is connected"
WARNING: net/mac80211/main.c:212
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]()
Hardware name: 64756D6
Pid: 3835, comm: ifconfig Tainted: G O
3.3.0-rc3-wl #9
Call Trace:
[<c0133b02>] warn_slowpath_common+0x72/0xa0
[<fc8e8c3f>] ?
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<fc8e8c3f>] ?
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<c0133b52>] warn_slowpath_null+0x22/0x30
[<fc8e8c3f>]
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<fc8f9de3>] __ieee80211_recalc_idle+0x113/0x430
[mac80211]
[<fc8fabc6>] ieee80211_do_open+0x156/0x7e0 [mac80211]
[<fc8f8a25>] ?
ieee80211_check_concurrent_iface+0x25/0x180 [mac80211]
[<c015dd9f>] ? raw_notifier_call_chain+0x1f/0x30
[<fc8fb290>] ieee80211_open+0x40/0x80 [mac80211]
[<c05894f6>] __dev_open+0x96/0xe0
[<c068fba5>] ? _raw_spin_unlock_bh+0x35/0x40
[<c05881d9>] __dev_change_flags+0x109/0x170
[<c0589423>] dev_change_flags+0x23/0x60
[<c05f3770>] devinet_ioctl+0x6a0/0x770
ieee80211 phy0: device no longer idle - in use
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rate control algorithms concludes the rate as invalid
with rate[i].idx < -1 , while they do also check for rate[i].count is
non-zero. it would be safer to zero initialize the 'count' field.
recently we had a ath9k rate control crash where the ath9k rate control
in ath_tx_status assumed to check only for rate[i].count being non-zero
in one instance and ended up in using invalid rate index for
'connection monitoring NULL func frames' which eventually lead to the crash.
thanks to Pavel Roskin for fixing it and finding the root cause.
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Cc: stable@vger.kernel.org
Cc: Pavel Roskin <proski@gnu.org>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The connectable/discoverable flags need to be changed before sending the
response since otherwise the settings value will be incorrect.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Now that most flags are persistent, only the LE_SCAN flag should be
cleared after a reset.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
When powered off and doing changes to the Connectable or Discoverable
setting we should also send an appropriate New Settings event in
addition to the command response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The New Settings event needs to be sent from quite many places so it
makes sense to have a convenience function for it to simplify the code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
We should not stop iterating through the various settings if powered off
since most may still be set even then.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
When switching connectable mode off any pending discoverable timeout
must also be disabled to avoid duplicate write_scan_enable commands.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes it possible to toggle the connectable & discoverable
settings when powered off. Two new hdev->dev_flags flags are added to
track what the scan mode should be when the device is finally powered
on.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The call_rcu() in mesh_gate_del() invokes mesh_gate_node_reclaim(),
which simply calls kfree(). So convert the call_rcu() to kfree_rcu(),
allowing mesh_gate_node_reclaim() to be eliminated.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
The call_rcu() in do_ip_setsockopt() invokes opt_kfree_rcu(), which just
calls kfree(). So convert the call_rcu() to kfree_rcu(), which allows
opt_kfree_rcu() to be eliminated.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Because opt_kfree_rcu() just calls kfree(), all call_rcu() uses of it
may be converted to kfree_rcu(). This permits opt_kfree_rcu() to
be eliminated.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
When mgmt is not in use the HCI_PAIRABLE flag will get implicitly set so
that pairing still works with old user space versions. However, as soon
as mgmt comes into play we should clear this flag so that it can be
properly set through the set_pairable command by user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch ensures that Set Fast Connectable fails apropriately if we
are not already in a connectable state (which is a pre-requisite for
fast connectable).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Both the Set Local Name and the Set Device Class commands should fail if
the adapter is not powered on.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Having the HCI_AUTO_OFF flag set means that from a mgmt interface
perspective we're still not powered, so all tests for HCI_UP should also
include a test for HCI_AUTO_OFF. This patch adds a convenience macro for
it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Marcell Zambo and Janos Farago noticed and reported that when
new conntrack entries are added via netlink and the conntrack table
gets full, soft lockup happens. This is because the nf_conntrack_lock
is held while nf_conntrack_alloc is called, which is in turn wants
to lock nf_conntrack_lock while evicting entries from the full table.
The patch fixes the soft lockup with limiting the holding of the
nf_conntrack_lock to the minimum, where it's absolutely required.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When the controller gets brought up for initial setup, it will be brought
back down after a timeout. In that case, don't send a New Settings event.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Neal Cardwell