This patch extends PCI-E driver to support PCI-E for APM821xx SoC on Bluestone
board.
Signed-off-by: Vinh Nguyen Huu Tuong <vhtnguyen@apm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Needed if you want to use swiotlb, harmless otherwise.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Currituck doesn't need nor use SDR so aborting the pci setup if there is
no sdr-base would be bad.
Add a flag to ppc4xx_pciex_hwops for the backends to state if they need
SDR and then only complain and abort if they do and it's not found in
the device tree.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The various port_init_hw methods of ppc4xx_pciex_hwops should have been
marked __init and when I added ppc4xx_pciex_port_reset_sdr(), which is
__init. This added many section mismatch warnings like:
WARNING: arch/powerpc/sysdev/built-in.o(.text+0x5c68): Section mismatch in reference from the function ppc440spe_pciex_init_port_hw() to the function .init.text:ppc4xx_pciex_port_reset_sdr()
The function ppc440spe_pciex_init_port_hw() references
the function __init ppc4xx_pciex_port_reset_sdr().
This is often because ppc440spe_pciex_init_port_hw lacks a __init
annotation or the annotation of ppc4xx_pciex_port_reset_sdr is wrong.
Trivial patch to silence those warnings.
Reported-By: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Yours Tony
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adds a register to the config space for the 460sx. Changes the vc0
detect to a pll detect. maps configuration space to test the link
status. changes the setup to enable gen2 devices to operate at gen2
speeds. fixes mapping that was not correct for the 460sx. added
bit definitions for the OMRxMSKL registers. Removed reserved bit
that was set incorrectly in the OMR2MSKL register.
tested on the 460sx eiger and custom board
Signed-off-by: Ayman El-Khashab <ayman@elkhashab.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Commit 112d1fe9f7
"powerpc/4xx: Add check_link to struct ppc4xx_pciex_hwops" inadvertently
broke 405 builds due to some functions being over protected by an
ifdef CONFIG_44x.
Move them back out.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
Move the "Checking link..." printk to the function that actually checks the
linke.
Reported-by: Ayman El-Khashab <ayman@elkhashab.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This renames pci flags functions and enums in preparation for creating
generic version in asm-generic/pci-bridge.h. The following search and
replace is done:
s/ppc_pci_/pci_/
s/PPC_PCI_/PCI_/
Direct accesses to ppc_pci_flag variable are replaced with helper
functions.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
All current pcie controllers unconditionally use SDR to check the link and
poll for reset. Refactor the code to include device reset in the
port_init_hw() op and add a new check_link() op.
This will make room fro new controllers that do not use SDR for these
operations.
Tested on 460ex.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Some of the newer 4xx pci cores need an explicit bit set to send
type 1 transactions instead of just comparing the bus numbers.
This patch enables type 1 transations for pcix nodes, thus enabling
devices behind PCI bridges.
Signed-off-by: Stef van Os <stef.van.os@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI 2.x cells used on some 44x SoCs only let us configure the decode
for the low 32-bit of the incoming PLB addresses. The top 4 bits (this
is a 36-bit bus) are hard wired to different values depending on the
specific SoC in use. Our code used to work "by accident" until I added
support for the ISA memory holes and while at it added more validity
checking of the addresses.
This patch should bring it back to working condition. It still relies
on the device-tree being correct but that's somewhat a pre-requisite
for anything to work anyway.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
4xx chips commonly now have multiple PHBs, there is no reason to not
enable PCI domains on them. The main issue with PCI domains is X but
currently its already somewhat busted for other reasons such as the
36-bit physical address space, which I'm fixing separately.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds support for ISA memory holes on the PCI, PCI-X and
PCI-E busses of the 4xx platforms. The patch includes changes
to the Bamboo and Canyonlands device-trees to add such a hole,
others can be updated separately.
The ISA memory hole is an additional outbound window configured
in the bridge to generate PCI cycles in the low memory addresses,
thus allowing to access things such as the hard-decoded VGA
aperture at 0xa0000..0xbffff or other similar things. It's made
accessible to userspace via the new legacy_mem file in sysfs for
which support was added by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch allows the 4xx (conventional) PCI bridge to be disabled
via the device tree. This is needed for 4xx PCI adapter hardware.
Use the PCI node's status property to disable the PCI bridge.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
There's no good reason why a resource_size_t shouldn't just be a
physical address, so simply redefine it in terms of phys_addr_t.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The declaration of total_memory removed. Now including <mm/mmu_decl.h>
instead. Since total_memory is a phys_addr_t which is 64-bit on 44x and
is_power_of_2() works with u32 so I just inlined (size & (size-1)) != 0
instead.
Also this patch fixes default initialization: res->end should be 0x7fffffff
not 0x80000000.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
During recent tests with PCI-E , it has been found the
DRV + De-Emphasis values are not optimum. These new values
are tested thouroughly.
Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Feng Kan fkan@amcc.com
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The 440EPx/GRx chips don't support PCI MRM commands. Drivers determine this
by looking for a zero value in the PCI cache line size register. However,
some drivers write to this register upon initialization. This can cause
MRMs to be used on these chips, which may cause deadlocks on PLB4.
The workaround implemented here introduces a new indirect_type flag, called
PPC_INDIRECT_TYPE_BROKEN_MRM. This is set in the pci_controller structure in
the pci fixup function for 4xx PCI bridges by determining if the bridge is
compatible with 440EPx/GRx. The flag is checked in the indirect_write_config
function, and forces any writes to the PCI_CACHE_LINE_SIZE register to be
zero, which will disable MRMs for these chips.
A similar workaround has been tested by AMCC on various PCI cards, such as
the Silicon Image ATA card and Intel E1000 GIGE card. Hangs were seen with
the Silicon Image card, and MRMs were seen on the bus with a PCI analyzer.
With the workaround in place, the card functioned properly and only Memory
Reads were seen on the bus with the analyzer.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch add a check to the PPC4xx PCIe driver to detect if the port
is disabled via the device-tree. This is needed for the AMCC Canyonlands
board which has an option to either select 2 PCIe ports or 1 PCIe port
and one SATA port. The SATA port and the 1st PCIe port pins are multiplexed
so we can't start both drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds basic endpoint support to the 4xx PCIe driver.
This is done by checking the device_type property of the PCIe
device node ("pci" for root-complex and "pci-endpoint" for endpoint
configuration).
Note: Currently we map a fixed 64MByte window to PLB address 0 (SDRAM).
This should probably be configurable via a dts property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The patch fixes a bug, where the PESDRn_UTLSET1 register was setup
wrongly resulting in a non working PCIe port 1. With this fix both
PCIe ports work fine again.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Since the arch/powerpc PCI subsystem now does a complete re-assignment of
the resources, we can move from the unconditional PCIe PHY reset to the
conditional version. Now the PHY is only reset, if no link is established yet.
An additional PHY reset (one is already done in U-Boot) leads to problems
with some Atheros PCIe boards and some HP FPGA PCIe designs.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
All this code is needed to properly initialize the 460EX PCIe host
bridge(s). We re-initialize all ports again, even though this has been done
in the bootloader (U-Boot) before. This way we make sure, that we always
run the latest init code in Linux and don't depend on code versions from
U-Boot.
Unfortunately all IBM/AMCC chips currently supported in this PCIe driver need
a different reset-/init-sequence.
Tested on AMCC Canyonlands eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Because of how big mapping the config space is (1M per bus), we limit how
many busses we support for now. In the long run, we could replace that
with something akin to kmap_atomic instead.
This patch changes the limit from currently 16 to 64.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch sets the ibpre flag (Inbound Presence) for the 405EX
in the 4xx PCIe driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds runtime detection of the 440SPe revision A chips. These
chips are equipped with a slighly different PCIe core and need special/
different initialization. The compatible node is changed to
"plb-pciex-440spe" ("A" and "B" dropped). This is needed for boards that
can be equipped with both PPC revisions like the AMCC Yucca.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This improves the way the 4xx PCI-E code handles checking for a link
and adds explicit testing of CRS result codes on config space accesses.
This should make it more reliable.
Also, bridges with no link are now still created, though config space
accesses beyond the root complex are filtered. This is one step toward
eventually supporting hotplug.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds to the previous 2 patches the support for the 4xx PCI Express
cells as found in the 440SPe revA, revB and 405EX.
Unfortunately, due to significant differences between these, and other
interesting "features" of those pieces of HW, the code isn't as simple
as it is for PCI and PCI-X and some of the functions differ significantly
between the 3 implementations. Thus, not only this code can only support
those 3 implementations for now and will refuse to operate on any other,
but there are added ifdef's to avoid the bloat of building a fairly large
amount of code on platforms that don't need it.
Also, this code currently only supports fully initializing root complex
nodes, not endpoint. Some more code will have to be lifted from the
arch/ppc implementation to add the endpoint support, though it's mostly
differences in memory mapping, and the question on how to represent
endpoint mode PCI in the device-tree is thus open.
Many thanks to Stefan Roese for testing & fixing up the 405EX bits !
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds to the previous patch the support for the 4xx PCI 2.x
bridges.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds base support code for the 4xx PCI-X bridge. It also provides
placeholders for the PCI and PCI-E version but they aren't supported
with this patch.
The bridges are configured based on device-tree properties.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Vinh Nguyen Huu Tuong