Commit Graph

51 Commits

Author SHA1 Message Date
Wolfram Sang 16735d022f tree-wide: use reinit_completion instead of INIT_COMPLETION
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.

[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-11-15 09:32:21 +09:00
Oleksandr Kozaruk 3a2d3d213d drivers: misc: ti-st: fix potential race if st_kim_start fails
If st_kim_start() fails registered protocols should be removed. This is
done by calling st_reg_complete(), which as comment states is called
with spin lock held. But in st_register() when st_kim_start fails it
is called without holding spin lock, creating possibility of concurrent
access to st_gdata data members.
Hold spin lock while calling st_reg_complete if st_kim_start() fails.

Signed-off-by: Oleksandr Kozaruk <oleksandr.kozaruk@globallogic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-30 12:08:04 -07:00
Jingoo Han 9093ca8891 misc: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-30 21:46:15 +09:00
Linus Torvalds 7ed214ac20 Char/Misc driver patches for 3.9-rc1
Here's the big char/misc driver patches for 3.9-rc1.
 
 Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
 extcon, vmci, etc.).
 
 All of these have been in the linux-next tree for a while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
 x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
 =i5HH
 -----END PGP SIGNATURE-----

Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc driver patches from Greg Kroah-Hartman:
 "Here's the big char/misc driver patches for 3.9-rc1.

  Nothing major here, just lots of different driver updates (mei,
  hyperv, ipack, extcon, vmci, etc.).

  All of these have been in the linux-next tree for a while."

* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
  w1: w1_therm: Add force-pullup option for "broken" sensors
  w1: ds2482: Added 1-Wire pull-up support to the driver
  vme: add missing put_device() after device_register() fails
  extcon: max8997: Use workqueue to check cable state after completing boot of platform
  extcon: max8997: Set default UART/USB path on probe
  extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
  extcon: max8997: Set default of ADC debounce time during initialization
  extcon: max8997: Remove duplicate code related to set H/W line path
  extcon: max8997: Move defined constant to header file
  extcon: max77693: Make max77693_extcon_cable static
  extcon: max8997: Remove unreachable code
  extcon: max8997: Make max8997_extcon_cable static
  extcon: max77693: Remove unnecessary goto statement to improve readability
  extcon: max77693: Convert to devm_input_allocate_device()
  extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
  CREDITS: update email and address of Harald Hoyer
  extcon: arizona: Use MICDET for final microphone identification
  extcon: arizona: Always take the first HPDET reading as the final one
  extcon: arizona: Clear _trig_sts bits after jack detection
  extcon: arizona: Don't HPDET magic when headphones are enabled
  ...
2013-02-21 13:57:13 -08:00
Greg Kroah-Hartman 9f9cba810f Merge 3.8-rc5 into tty-next
This resolves a number of tty driver merge issues found in linux-next

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-25 13:27:36 -08:00
Luciano Coelho a7e2ca1703 Revert "drivers/misc/ti-st: remove gpio handling"
This reverts commit eccf2979b2.

The reason is that it broke TI WiLink shared transport on Panda.
Also, callback functions should not be added to board files anymore,
so revert to implementing the power functions in the driver itself.

Additionally, changed a variable name ('status' to 'err') so that this
revert compiles properly.

Cc: stable <stable@vger.kernel.org> [3.7]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-22 17:22:47 -08:00
Luciano Coelho 55cd0e36f6 Revert "drivers/misc/ti-st: remove gpio handling"
This reverts commit eccf2979b2.

The reason is that it broke TI WiLink shared transport on Panda.
Also, callback functions should not be added to board files anymore,
so revert to implementing the power functions in the driver itself.

Additionally, changed a variable name ('status' to 'err') so that this
revert compiles properly.

Cc: stable <stable@vger.kernel.org> [3.7]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-21 14:29:03 -08:00
Joe Millenbach 4f73bc4dd3 tty: Added a CONFIG_TTY option to allow removal of TTY
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.

The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer.  Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.

bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY.  The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.

add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function                                     old     new   delta
chr_dev_init                                 166     170      +4
allow_signal                                  80      82      +2
static.__warned                              143     142      -1
disallow_signal                               63      62      -1
__set_special_pids                            95      94      -1
unregister_console                           126     121      -5
start_kernel                                 546     541      -5
register_console                             593     588      -5
copy_from_user                                45      40      -5
sys_setsid                                   128     120      -8
sys_vhangup                                   32      19     -13
do_exit                                     1543    1526     -17
bitmap_zero                                   60      40     -20
arch_local_irq_save                          137     117     -20
release_task                                 674     652     -22
static.spin_unlock_irqrestore                308     260     -48

Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-18 16:15:27 -08:00
channing 25c22d5bea misc: st_core: Error triggered by convert "char" to "int"
When st driver decodes protocol index received from raw data,
it does a value convert from "char" to "int". Because it's sign
extension from bit8 to bit32, the "int" value maybe minus, in
another word, the protocol index might be minus, but driver doesn't
filter such case and may continue access memory pointed by this
minus index.

This patch is to change the variable type of index from "int"
to "unsigned char", so that it avoids do such kind of type
conversion.

cc: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-17 10:19:42 -08:00
Matthias Kaehlcke b2997387c2 misc/st_kim: Free resources in the error path of probe()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-26 16:16:35 -08:00
Wei Yongjun 35299f884a drivers:misc: ti-st: fix potential NULL pointer dereference in st_register()
Remove the pointless NULL dereference above the NULL test.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-24 15:52:29 -07:00
Matthias Kaehlcke 877cdf3949 drivers/misc/ti-st: check chip_awake NULL check
Before calling on any of the platform hooks, shared transport driver checks
for the validity of the platform hooks as to whether it is provided or not.
A wrong function was being checked for, before the chip_awake hook was called
by the HCI-LL sleep logic handler. This patch corrects the check.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16 10:11:45 -07:00
Pavan Savoy 8565adbc82 drivers/misc/ti-st: fix read fw version cmd
If the read firmware version response from the chip is split into multiple
frames of UART buffer being received by the host, the TI-ST driver as of today
is unable to put the pieces of response together unlike other responses.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16 10:11:45 -07:00
Pavan Savoy 537023580d drivers/misc/ti-st: use cpu friendly completions
Be nice to CPU and don't hog the resources, use a nice wait_for_interruptible
timeout for completions instead of wait_for_timeout which is
non-interruptible.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16 10:11:45 -07:00
Pavan Savoy b64365a526 drivers/misc/ti-st: chip_disable on timeout
If the communication with the WiLink breaks down for whatever reasons & the
ti-st driver is unable to un-install the line-discipline during clean-up in
st_kim_stop, the GPIO should be held low (BT_EN=0) & the platform's chip
disable hook shall also be called.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16 10:11:45 -07:00
Pavan Savoy 27712b3928 drivers/misc/ti-st: remove sparse warnings
remove sparse warnings by assigning right storage specifiers to functions and
also clean-up the declarations in the include/linux/ti_wilink_st.h

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16 10:11:45 -07:00
Pavan Savoy eccf2979b2 drivers/misc/ti-st: remove gpio handling
A platform hook to enable/disable the chip was introduced to perform specific
activities to power-up and power-down the WL chip.
Moving the power-up/down sequence also there makes more sense, since different
platforms have begun to have their own ways to power-up/down the chip.
This patch removes all of the gpio handling done by the driver in
st_kim_start/st_kim_stop & any of the gpio request done in the probe function.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16 10:11:45 -07:00
Alan Cox 5353cf089b drivers/misc/ti-st/st_core.c: missing NULL check
Addresses https://bugzilla.kernel.org/show_bug.cgi?44431

Reported-by: <rucsoftsec@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-07-30 17:25:13 -07:00
Axel Lin b00e126ffe MISC: convert drivers/misc/* to use module_platform_driver()
This patch converts the drivers in drivers/misc/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Pavan Savoy <pavan_savoy@ti.com>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Acked-By: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2012-01-24 16:31:48 -08:00
Pavan Savoy 933aae54be drivers:misc: ti-st: DEBUG uart, baud rate mods
To debug different UARTs at different baud-rates connected to the WiLink
connectivity combo-chipset, this patch enables the debugging code so that upon
boot different UARTs at different baud-rates can be tried out to verify the
interface with WiLink.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2012-01-04 15:21:04 -08:00
Pavan Savoy 18ccecf99a drivers:misc: ti-st: flush UART upon fw failure
Upon failure to read firmware version from chip or upon failure in responses
to firmware download the UART needs to be flushed of its existing buffers so
that the UIM can restart UART properly.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2012-01-04 15:21:04 -08:00
Pavan Savoy bfb88d6c91 drivers:misc: ti-st: protect registrations
Concurrent access to UART2/combo-interface by multiple protocol drivers such
as BT, FM and GPS caused issues during firmware download failure cases or
cases when the firmware download took longer than usual.

This was because of un-safe access to protos_registered & st_states.
Protecting this will also make the registration complete callback un-safe for
sleep.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2012-01-04 15:21:03 -08:00
Paul Gortmaker eb12a679b2 drivers/misc: Add module.h to files who are really modular.
These files really need the full module.h header file present, but
were just getting it implicitly before.  Fix it up in advance so we
avoid build failures once the cleanup commit is present.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:31:53 -04:00
Pavan Savoy 651d62a8b0 drivers:misc: ti-st: fix unexpected UART close
If suppose the UIM were to die and hence UART were to close when the
Bluetooth/FM or GPS is turned on, prep the ST for a state where-in if
the UIM comes back up, Bluetooth/FM/GPS can be turned on.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:35 -07:00
Pavan Savoy 76ff0e64d4 drivers:misc: ti-st: free skb on firmware download
If during validation of the firmware download the data doesn't match what is
expected out of the chip, this calls for a firmware download failure and a
retry.
Free the SKB which collects response during such scenarios.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:34 -07:00
Pavan Savoy d0344ef670 drivers:misc: ti-st: wait for completion at fail
When the line discipline install fails for reasons such as missing user-space
UIM or broken communication between UIM and ST driver, then the ST
attempts/retries to request for ldisc installation again.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:34 -07:00
Pavan Savoy 2f81a02ce0 drivers:misc: ti-st: reinit completion before send
download firmware behaves differently at different times, when logs are
enabled and the system is loaded, the wait_for_completion is able to wait for
every send, However during other times the wait does not happen.

So, for reliability reinitializing the completion before every send, makes
sure the wait happens for every send.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:33 -07:00
Vijay Badawadagi 78bb9697e2 drivers:misc: ti-st: fail-safe on wrong pkt type
Texas Instrument's shared transport driver interpret incoming data from the
UART based on the various protocol drivers registered to the driver such as
btwilink driver or FM or GPS driver which provide logical channel IDs.

In case of bad-behavior from chip such as HCI Event response for a GPS command
or a HCI Event (h/w error event) for a FM response & In case of bad-behavior
from UART driver such as dropping data bytes a fail-safe is required to avoid
kernel panic.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Vijay Badawadagi <bvijay@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:33 -07:00
Pavan Savoy 74a4fcf19e drivers:misc: ti-st: reinit completion on ver read
After the version information has been read, the completion which assists in
wait_for_completion during the firmware send/wait sequence is being re-used
and hence this needs to be re-initialised for fool proof firmware download
retries.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:32 -07:00
Pavan Savoy 0d7c5f2572 drivers:misc:ti-st: platform hooks for chip states
Certain platform specific or Host-WiLink Interface specific actions would be
required to be taken when the chip is being enabled and after the chip is
disabled such as configuration of the mux modes for the GPIO of host connected
to the nshutdown of the chip or relinquishing UART after the chip is disabled.

Similar actions can also be taken when the chip is in deep sleep or when the
chip is awake. Performance enhancements such as configuring the host to run
faster when chip is awake and slower when chip is asleep can also be made
here.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:32 -07:00
Pavan Savoy 5926cef26c drivers:misc: ti-st: avoid a misleading dbg msg
Previously the private data of each protocol registered to use ST was
used to determine whether the protocol was registered to use shared
transport or otherwise.
However, now a flag is_registered is maintained to identify whether a
protocol intends to use ST.
Upon closing of the UART the error message relevant to this lack of
un-registration was misleading and this patch fixes that.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 14:13:31 -07:00
Shahar Lev 9d031d94da drivers:misc: ti-st: fix skipping of change remote baud
Before the incrementing of ptr in skip_change_remote_baud,
it points to cur_action, but the increment is done by
the size of nxt_action instead. This could cause ptr
to not point to a bts_action structure, which is
harmful for the increment of ptr done in download_firmware.
Therefore, the skipping is first done for cur_action.

Signed-off-by: Shahar Lev <shahar@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-06-07 10:01:18 -07:00
Steven Rostedt 7316a9f2a9 st_kim: Handle case of no device found for ID 0
Running ktest.pl, I hit this bug:

[   19.780654] BUG: unable to handle kernel NULL pointer dereference at 0000000c
[   19.780660] IP: [<c112efcd>] dev_get_drvdata+0xc/0x46
[   19.780669] *pdpt = 0000000031daf001 *pde = 0000000000000000
[   19.780673] Oops: 0000 [#1] SMP
[   19.780680] Dumping ftrace buffer:^M
[   19.780685]    (ftrace buffer empty)
[   19.780687] Modules linked in: ide_pci_generic firewire_ohci firewire_core evbug crc_itu_t e1000 ide_core i2c_i801 iTCO_wdt
[   19.780697]
[   19.780700] Pid: 346, comm: v4l_id Not tainted 2.6.39-test-02740-gcaebc16-dirty #4                  /DG965MQ
[   19.780706] EIP: 0060:[<c112efcd>] EFLAGS: 00010202 CPU: 0
[   19.780709] EIP is at dev_get_drvdata+0xc/0x46
[   19.780712] EAX: 00000008 EBX: f1e37da4 ECX: 00000000 EDX: 00000000
[   19.780715] ESI: f1c3f200 EDI: c33ec95c EBP: f1e37d80 ESP: f1e37d80
[   19.780718]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[   19.780721] Process v4l_id (pid: 346, ti=f1e36000 task=f2bc2a60 task.ti=f1e36000)
[   19.780723] Stack:
[   19.780725]  f1e37d8c c117d395 c33ec93c f1e37db4 c117a0f9 00000002 00000000 c1725e54
[   19.780732]  00000001 00000007 f2918c90 f1c3f200 c33ec95c f1e37dd4 c1789d3d 22222222
[   19.780740]  22222222 22222222 f2918c90 f1c3f200 f29194f4 f1e37de8 c178d5c4 c1725e54
[   19.780747] Call Trace:
[   19.780752]  [<c117d395>] st_kim_ref+0x28/0x41
[   19.780756]  [<c117a0f9>] st_register+0x29/0x562
[   19.780761]  [<c1725e54>] ? v4l2_open+0x111/0x1e3
[   19.780766]  [<c1789d3d>] fmc_prepare+0x97/0x424
[   19.780770]  [<c178d5c4>] fm_v4l2_fops_open+0x70/0x106
[   19.780773]  [<c1725e54>] ? v4l2_open+0x111/0x1e3
[   19.780777]  [<c1725e9b>] v4l2_open+0x158/0x1e3
[   19.780782]  [<c065173b>] chrdev_open+0x22c/0x276
[   19.780787]  [<c0647c4e>] __dentry_open+0x35c/0x581
[   19.780792]  [<c06498f9>] nameidata_to_filp+0x7c/0x96
[   19.780795]  [<c065150f>] ? cdev_put+0x57/0x57
[   19.780800]  [<c0660cad>] do_last+0x743/0x9d4
[   19.780804]  [<c065d5fc>] ? path_init+0x1ee/0x596
[   19.780808]  [<c0661481>] path_openat+0x10c/0x597
[   19.780813]  [<c05204a1>] ? trace_hardirqs_off+0x27/0x37
[   19.780817]  [<c0509651>] ? local_clock+0x78/0xc7
[   19.780821]  [<c0661945>] do_filp_open+0x39/0xc2
[   19.780827]  [<c1cabc76>] ? _raw_spin_unlock+0x4c/0x5d^M
[   19.780831]  [<c0674ccd>] ? alloc_fd+0x19e/0x1b7
[   19.780836]  [<c06499ca>] do_sys_open+0xb7/0x1bd
[   19.780840]  [<c0608eea>] ? sys_munmap+0x78/0x8d
[   19.780844]  [<c0649b06>] sys_open+0x36/0x58
[   19.780849]  [<c1cb809f>] sysenter_do_call+0x12/0x38
[   19.780852] Code: d8 2f 20 c3 01 83 15 dc 2f 20 c3 00 f0 ff 00 83 05 e0 2f 20 c3 01 83 15 e4 2f 20 c3 00 5d c3 55 89 e5 3e 8d 74 26 00 85 c0 74 28 <8b> 40 04 83 05 e8 2f 20 c3 01 83 15 ec 2f 20 c3 00 85 c0 74 13 ^M
[   19.780889] EIP: [<c112efcd>] dev_get_drvdata+0xc/0x46 SS:ESP 0068:f1e37d80
[   19.780894] CR2: 000000000000000c
[   19.780898] ---[ end trace e7d1d0f6a2d1d390 ]---

The id of 0 passed to st_kim_ref() found no device, keeping pdev null,
and causing pdev->dev cause a NULL pointer dereference. After having
st_kim_ref() check for NULL, the st_unregister() function needed to be
updated to handle the case that st_gdata was not set by the
st_kim_ref().

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-06-07 10:01:16 -07:00
Linus Torvalds 55db4c64ed Revert "tty: make receive_buf() return the amout of bytes received"
This reverts commit b1c43f82c5.

It was broken in so many ways, and results in random odd pty issues.

It re-introduced the buggy schedule_work() in flush_to_ldisc() that can
cause endless work-loops (see commit a5660b41af6a: "tty: fix endless
work loop when the buffer fills up").

It also used an "unsigned int" return value fo the ->receive_buf()
function, but then made multiple functions return a negative error code,
and didn't actually check for the error in the caller.

And it didn't actually work at all.  BenH bisected down odd tty behavior
to it:
  "It looks like the patch is causing some major malfunctions of the X
   server for me, possibly related to PTYs.  For example, cat'ing a
   large file in a gnome terminal hangs the kernel for -minutes- in a
   loop of what looks like flush_to_ldisc/workqueue code, (some ftrace
   data in the quoted bits further down).

   ...

   Some more data: It -looks- like what happens is that the
   flush_to_ldisc work queue entry constantly re-queues itself (because
   the PTY is full ?) and the workqueue thread will basically loop
   forver calling it without ever scheduling, thus starving the consumer
   process that could have emptied the PTY."

which is pretty much exactly the problem we fixed in a5660b41af.

Milton Miller pointed out the 'unsigned int' issue.

Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Milton Miller <miltonm@bga.com>
Cc: Stefan Bigler <stefan.bigler@keymile.com>
Cc: Toby Gray <toby.gray@realvnc.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-06-04 06:33:24 +09:00
Linus Torvalds 99dff58562 Merge branch 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (48 commits)
  serial: 8250_pci: add support for Cronyx Omega PCI multiserial board.
  tty/serial: Fix break handling for PORT_TEGRA
  tty/serial: Add explicit PORT_TEGRA type
  n_tracerouter and n_tracesink ldisc additions.
  Intel PTI implementaiton of MIPI 1149.7.
  Kernel documentation for the PTI feature.
  export kernel call get_task_comm().
  tty: Remove to support serial for S5P6442
  pch_phub: Support new device ML7223
  8250_pci: Add support for the Digi/IBM PCIe 2-port Adapter
  ASoC: Update cx20442 for TTY API change
  pch_uart: Support new device ML7223 IOH
  parport: Use request_muxed_region for IT87 probe and lock
  tty/serial: add support for Xilinx PS UART
  n_gsm: Use print_hex_dump_bytes
  drivers/tty/moxa.c: Put correct tty value
  TTY: tty_io, annotate locking functions
  TTY: serial_core, remove superfluous set_task_state
  TTY: serial_core, remove invalid test
  Char: moxa, fix locking in moxa_write
  ...

Fix up trivial conflicts in drivers/bluetooth/hci_ldisc.c and
drivers/tty/serial/Makefile.

I did the hci_ldisc thing as an evil merge, cleaning things up.
2011-05-23 12:23:20 -07:00
Randy Dunlap 773d67903a misc: fix ti-st build issues
st_drv uses skb*() interfaces, so it should depend on NET.
It also uses GPIO interfaces, so it should depend on GPIOLIB.

st_kim.c uses syss_*() calls, so it should #include
<linux/sysfs.h>.

Fixes these observed build errors:
ERROR: "skb_queue_purge" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_pull" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_queue_tail" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "__alloc_skb" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "kfree_skb" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_dequeue" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_put" [drivers/misc/ti-st/st_drv.ko] undefined!

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-29 14:11:03 -07:00
Felipe Balbi b1c43f82c5 tty: make receive_buf() return the amout of bytes received
it makes it simpler to keep track of the amount of
bytes received and simplifies how flush_to_ldisc counts
the remaining bytes. It also fixes a bug of lost bytes
on n_tty when flushing too many bytes via the USB
serial gadget driver.

Tested-by: Stefan Bigler <stefan.bigler@keymile.com>
Tested-by: Toby Gray <toby.gray@realvnc.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-22 17:31:53 -07:00
Pavan Savoy fc2711992b drivers:misc:ti-st: remove rfkill dependency
rfkill is no longer used by Texas Instruments shared transport driver to
communicate with user-space.
This patch removes the dependency of rfkill to be enabled to build
shared transport driver in the Kconfig.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-22 17:01:09 -07:00
Pavan Savoy 764b0c4b32 drivers:misc:ti-st: handle delayed tty receive
When certain technologies shutdown their interface without waiting for
the acknowledgement from the chip. The receive_buf from the TTY would be
invoked a while after the relevant technology is unregistered.

This patch introduces a new flag "is_registered" which maintains the
state of protocols BT, FM or GPS and thereby removes the need to clear
the protocol data from ST when protocols gets unregistered.

This fixes corner cases when HCI RESET is sent down from bluetooth stack
and the receive_buf is called from tty after 250ms before which
bluetooth would have unregistered from the system.
OR - when FM application decides to close down the device without
sending a power-off FM command resulting in some RDS data or interrupt
data coming in after the driver is unregistered.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-22 17:01:09 -07:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Pavan Savoy c1605f2e33 drivers:misc: ti-st: fix debugging code
debug code in TI-ST driver can be enabled by #defining
DEBUG in the first line of the code and in case debugfs
is mounted, the 2 entries in /sys/kernel/debug/ti-st/ will
also provide useful information.
These 2 were broken because of the recent changes to the parsing
logic and the registration mechanism of the protocol drivers,
this patch fixes them.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-03-09 16:10:00 -08:00
Pavan Savoy 781a7395d2 drivers:misc: ti-st: remove multiple gpio handling
TI shared transport driver previously intended to expose rfkill
entries for each of the protocol gpio that the chip would have.
However now in case such gpios exist, which requires to be enabled
for a specific protocol, the responsibility lay on protocol driver.
This patch removes the request/free of multiple gpios, rfkill struct
references and also removes the chip_toggle function.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-04 12:41:21 -08:00
Pavan Savoy 6d71ba2105 drivers:misc: ti-st: fix hci-ll on wake_ind collision
Where file-transfer stops/pauses in between, is
result of a HCI-LL anamoly in ST LL driver.
ST LL did not copy the contents of WaitQ into the TxQ, when a WAKEUP_IND
collision happened.
Make also sure, that the copying mechanism is safe, by wrapping it around
spin locks inside st_int_recv().
This was easily reproduced when the sleep timeout was reduced to 100ms
for HCI-LL.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-04 12:41:21 -08:00
Pavan Savoy ef04d121f0 drivers:misc: ti-st: firmware download optimization
To fasten the process of firmware download, the chip allows
disabling of the command complete event generation from host.
In these cases, only few very essential commands would have
the command complete events and hence the wait associated with
them.

So now the driver would wait for a command complete event, only
when it comes across a wait event during firmware parsing.
This would also mean we need to skip not just the change baud
rate command but also the wait for it.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-04 12:41:21 -08:00
Pavan Savoy 6710fcff66 drivers:misc: ti-st: set right debug levels for logs
pr_debug-ing few pr_infos from the data paths such as tty receive and
write so as to reduce debugs when we have higher logging levels enabled
undef VERBOSE in receive to avoid huge logs when log level 8 is set.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-04 12:41:21 -08:00
Pavan Savoy 704426649d drivers:misc: ti-st: fix error codes
set-right the error codes that the shared transport driver
returns.
Instead of magic numbers like -1, return relevant codes such as
ETIMEDOUT or EIO, EAGAIN when wait times out or uart write bytes don't
match expected value or when registration fails and needs to be
attempted again.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-04 12:41:20 -08:00
Pavan Savoy ec60d0ad20 drivers:misc: ti-st: move from rfkill to sysfs
The communication between ST KIM and UIM was interfaced
over the /dev/rfkill device node.
Move the interface to a simpler less abusive sysfs entry
mechanism and document it in Documentation/ABI/testing/
under sysfs-platform-kim.

Shared transport driver would now read the UART details
originally received by bootloader or firmware as platform
data.
The data read will be shared over sysfs entries for the user-space
UIM or other n/w manager/plugins to be read, and assist the driver
by opening up the UART, setting the baud-rate and installing the
line discipline.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-04 12:41:20 -08:00
Pavan Savoy 5c88b02196 drivers:misc: ti-st: register with channel IDs
The architecture of shared transport had begun with individual
protocols like bluetooth, fm and gps telling the shared transport
what sort of protocol they are and then expecting the ST driver
to parse the incoming data from chip and forward data only
relevant to the protocol drivers.

This change would mean each protocol drivers would also send
information to ST driver as to how to intrepret their protocol
data coming out of the chip.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-04 12:41:20 -08:00
Pavan Savoy 73f12e8d3d drivers: misc: ti-st: fix review comments
Based on comments from Jiri Slaby, drop the register
storage specifier, remove the unused code, cleanup
the const to non-const type casting.
Also make the line discipline ops structure static, since
its a singleton, unmodified structure which need not be
in heap.

Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-14 12:41:10 -07:00
Pavan Savoy 2bb32e84a1 misc: ti-st: Kconfig & Makefile for TI_ST
Add the Kconfig and the Makefile for the TI_ST driver.
TI_ST driver is the line discipline driver for the Texas Instrument's
WiLink chipsets.
Also add the ti-st folder to list of drivers under drivers/misc.

Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-06 08:27:00 -07:00