This patch adds support for setting UHS-I bus speed mode during UHS-I
initialization procedure. Since both the host and card can support
more than one bus speed, we select the highest speed based on both of
their capabilities. First we set the bus speed mode for the card using
CMD6 mode 1, and then we program the host controller to support the
required speed mode. We also set High Speed Enable in case one of the
UHS-I modes is selected. We take care to reset SD clock before setting
UHS mode in the Host Control2 register, and then re-enable it as per
the Host Controller spec v3.00. We then set the clock frequency for
the UHS-I mode selected.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As per Host Controller spec v3.00, we reset SDCLK before setting
High Speed Enable, and then set it back to avoid generating clock
gliches. Before enabling SDCLK again, we make sure the clock is
stable, so we use sdhci_set_clock().
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for setting driver strength during UHS-I
initialization procedure. Since UHS-I cards set S18A (bit 24) in
response to ACMD41, we use this as a base for UHS-I initialization.
We modify the parameter list of mmc_sd_get_cid() so that we can
save the ROCR from ACMD41 to check whether bit 24 is set.
We decide whether the Host Controller supports A, C, or D driver
type depending on the Capabilities register. Driver type B is
suported by default. We then set the appropriate driver type for
the card using CMD6 mode 1. As per Host Controller spec v3.00, we
set driver type for the host only if Preset Value Enable in the
Host Control2 register is not set. SDHCI_HOST_CONTROL has been
renamed to SDHCI_HOST_CONTROL1 to conform to the spec.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SD cards which conform to Physical Layer Spec v3.01 can support
additional Bus Speed Modes, Driver Strength, and Current Limit
other than the default values. We use CMD6 mode 0 to read these
additional card functions. The values read here will be used
during UHS-I initialization steps.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.
Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.
If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allows appropriately-privileged applications to send CMD (normal) and ACMD
(application-specific; preceded with CMD55) commands to cards/devices on
the mmc bus. This is primarily useful for enabling the security
functionality built in to every SD card.
It can also be used as a generic passthrough (e.g. to enable virtual
machines to control mmc bus devices directly). However, this use case has
not been tested rigorously. Generic passthrough testing was only conducted
for a few non-security opcodes to prove the feasibility of the passthrough.
Since any opcode can be sent using this passthrough, it is very possible to
render the card/device unusable. Applications that use this ioctl must
have CAP_SYS_RAWIO.
Security commands tested on TI PCIxx12 (SDHCI), Sigma Designs SMP8652 SoC,
TI OMAP3621/OMAP3630 SoC, Samsung S5PC110 SoC, Qualcomm MSM7200A SoC.
Signed-off-by: John Calixto <john.calixto@modsystems.com>
Reviewed-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
To avoid lockdep warnings:
BUG: key dc90a520 not in .data!
------------[ cut here ]------------
WARNING: at /home/rabin/kernel/arm/kernel/lockdep.c:2701 sysfs_add_file_mode+0x4c/0xb0()
Modules linked in:
[<c004b5d8>] (unwind_backtrace+0x0/0xe4) from [<c0074f20>] (warn_slowpath_common+0x4c/0x64)
[<c0074f20>] (warn_slowpath_common+0x4c/0x64) from [<c0074f50>] (warn_slowpath_null+0x18/0x1c)
[<c0074f50>] (warn_slowpath_null+0x18/0x1c) from [<c0157fec>] (sysfs_add_file_mode+0x4c/0xb0)
[<c0157fec>] (sysfs_add_file_mode+0x4c/0xb0) from [<c02d61e4>] (mmc_add_disk+0x40/0x64)
[<c02d61e4>] (mmc_add_disk+0x40/0x64) from [<c02d64cc>] (mmc_blk_probe+0x188/0x1fc)
[<c02d64cc>] (mmc_blk_probe+0x188/0x1fc) from [<c02ce820>] (mmc_bus_probe+0x14/0x18)
...
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Chris Ball <cjb@laptop.org>
On HP laptops with JMicron 388 chip, the write-locked SD card isn't
detected correctly as read-only in many cases. This is because the
PRESENT_STATE register becomes unsable just after plugging, and it
returns the WRITE_PROTECT bit wrongly at the first read.
This patch fixes the read-only detection by adding a new sdhci quirk
indicating to check the register more intensively with a relatively
long delay.
The patch is tested with 2.6.39-rc4 kernel.
Cc: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
With the hardware partitions support (which represent additional logical
devices present on MMC), devidx does not correspond with index used to form
/dev/mmcblkX names. So use an additional allocated index for device names.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Marvell pxa controllers have private registers that may need to be
modified before and after a reset is done.
For example, the SD reset operation, RESET_ALL, will reset the private
registers to their default state. This will cause the clock adjustment
registers that may have been programmed to have incorrect values.
RESET_DATA sometimes needs to be delayed before the reset is done
(depending on SoC) to enable any transactions being handled by the
SDIO card to be completed. Needed in pre SD 3.0 silicon to handle
clock gating.
Implement hooks to allow this to happen.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit 373e6a (mmc: sdhci: R1B command handling + MMC_CAP_ERASE) moved the
handling of SDHCI_QUIRK_TIMEOUT_USES_SDCLK from sdhci_calc_timeout() to
sdhci_add_host(). This causes division by zero errors on at least the S3C
SDHCI controller as the quirk implementation needs host->clock set to work
but host->clock has not been set when sdhci_add_host() is called.
Fix this by backing out that portion of the change, the clock may vary at
runtime anyway. It does occur to me that we may want to move the quirk to
where we set the clock but this seems more invasive and I'm concerned
about undesirable side effects.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Converts from:
struct mmc_request mrq;
memset(&mrq, 0, sizeof(struct mmc_request));
to:
struct mmc_request mrq = {0};
because it's shorter, as performant, and easier to work out whether
initialization has happened.
Signed-off-by: Chris Ball <cjb@laptop.org>
Converts from:
struct mmc_data data;
memset(&data, 0, sizeof(struct mmc_data));
to:
struct mmc_data data = {0};
because it's shorter, as performant, and easier to work out whether
initialization has happened.
Signed-off-by: Chris Ball <cjb@laptop.org>
Converts from:
struct mmc_command cmd;
memset(&cmd, 0, sizeof(struct mmc_command));
to:
struct mmc_command cmd = {0};
because it's shorter, as performant, and easier to work out whether
initialization has happened.
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_cmd_app did not zero out mmc_command on stack.
Reported-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some SD host controllers (noticed on an integrated JMicron SD reader on an
HP Pavilion dv5-1250eo laptop) don't update the dma address register before
signaling a dma interrupt due to a dma boundary. Update the register
manually to the next boundary (by default 512KiB), at which the transfer
stopped.
As long as each transfer is at most 512KiB in size (guaranteed by a BUG_ON
in sdhci_prepare_data()) and the boundary is kept at the default value,
this fix is needed at most once per transfer. Smaller boundaries are taken
care of by counting the transferred bytes.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=28462
Signed-off-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Block quirks implemented using core/quirks.c support.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allows device MMC boot partitions to be accessed. MMC partitions are
treated effectively as separate block devices on the same MMC card.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Move host claim/release into mmc_blk_issue_rq.
(This is helpful so that selecting partition only has to happen
in one place for these commands.)
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
CMD6 is an R1B-type command, where DAT is used as busy. Depending
on register written using CMD6, timeout value can be different
as per spec.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ERASE command needs R1B response, so fix R1B-type command
handling for SDHCI controller. For non-DAT commands using a busy
response, the cmd->cmd_timeout_ms (in ms) field is used for timeout
calculations.
Based on patch by Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Renames erase_timeout to cmd_timeout_ms inside struct mmc_command.
First step to making host honor timeouts for non-data-transfer
commands. Cleans up erase timeout code.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The current mechanism is SDIO-only. This allows us to create
function-specific quirks, without creating messy Kconfig dependencies,
or polluting core/ with function-specific code.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
led_trigger_register_simple() allocates memory which must not be leaked
in the error-path of mmc_add_host. Move it past the only error-check in
the function.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes 21 errors and 6 warnings reported by checkpatch.pl.
Signed-off-by: Ameya Palande <2ameya@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The wl12xx device supports disconnecting the pull-up resistor on
CD/DAT[3] (pin 1) of the card.
Tell SDIO core to disconnect that resistor during card init,
since we don't need it at that point (and anyway all
hosts shall provide pull-up resistors on all data lines DAT[3:0]
as described in section 6 of the SD physical specification).
As a result, this may save some power, but it's also generally healthy
since it prevents both ends from pulling up that pin, which
results in undesirable asymmetric physical bus.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
006ebd5d introduced sdio_disable_cd(), which disconnects the pull-up
resistor on CD/DAT[3] (pin 1) of the card.
Make it possible to start using sdio_disable_cd() by introducing
MMC_QUIRK_DISABLE_CD.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Tell SDIO core to ignore the standard SDIO function interface
codes indicated by the wl1271. This is required because the
wl1271 erroneously indicates its first function as a standard
Bluetooth SDIO interface, and that drives btsdio mad.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Introduce MMC_QUIRK_NONSTD_FUNC_IF to ignore the "SDIO Standard Function
interface code" as indicated by the card's FBR, and instead treat all
functions as non-standard interfaces.
This is required to prevent standard drivers from facing
errors when trying to communicate with SDIO cards that erroneously
indicate standard function interface codes.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
6b5eda36 followed SDIO spec part E1 section 8, which states that
in case SDIO interrupts are being used to wake up a suspended host,
then it is required to switch to 1-bit mode before stopping the clock.
Before switching to 1-bit mode (or back to 4-bit mode on resume),
make sure that SDIO interrupts are really being used to wake the host.
This is helpful for devices which have an external irq line (e.g.
wl1271), and do not use SDIO interrupts to wake up the host.
In this case, switching to 1-bit mode (and back to 4-bit mode on resume)
is not necessary.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_card_is_powered_resumed is a mouthful; instead, simply use
mmc_card_keep_power, which also better explains the purpose of
the macro.
Employ mmc_card_keep_power() where possible.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allows reliable writes to be used for MMC writes. Reliable writes are used
to service write REQ_FUA/REQ_META requests. Handles both the legacy and
the enhanced reliable write support in MMC cards.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This config option is used to decide whether tegra sdhci support
should be build into the sdhci-platform module. So setting it 'm'
is nonsense, since we can't build part of an module as a module.
The effect for 'm' will probably be the same as for 'n'.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable fast bcm4329 WIFI suspend/resume on Tegra2 board.
This patch allows the mach-tegra support to tell the tegra MMC host
controller to NOT turn off power for the MMC controller the WIFI part
lives behind. Thus bcm4329 firmware doesn't need to be reloaded.
Signed-off-by: Venkat Rao <vrao@broadcom.com>
Tested-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Olof Johansson <olof@lixom.net>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is no need to disable irq's when using the sg_copy_*_buffer()
functions because those functions do that already. There are also
no races for the mm_queue struct here that would require the irq's
to be disabled before calling sg_copy_*_buffer().
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
uBoot sometimes leaves eMMC pointing to the private boot partition.
Ensure we always start looking at the user partition.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Bruce Clemens <bpclemens@marvell.com>
Signed-off-by: Mark F. Brown <markb@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: Make struct pcmcia_device_id const, sound drivers edition
staging: pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Make declaration and uses of struct pcmcia_device_id const
pcmcia/sa1100: put sa11x0_pcmcia_hw_init[] to .devinit.data
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (137 commits)
ARM: bcmring: convert to use sp804 clockevents
ARM: bcmring: convert to sp804 clocksource
ARM: 6912/1: bcmring: Add clkdev table in init_early
clockevents: ARM sp804: obtain sp804 timer rate via clks
clockevents: ARM sp804: allow clockevent name to be specified
clocksource: ARM sp804: obtain sp804 timer rate via clks
clocksource: ARM sp804: allow clocksource name to be specified
clocksource: convert OMAP1 to 32-bit down counting clocksource
clocksource: convert MXS timrotv2 to 32-bit down counting clocksource
clocksource: convert SPEAr platforms 16-bit up counting clocksource
clocksource: convert Integrator/AP 16-bit down counting clocksource
clocksource: convert W90x900 24-bit down counting clocksource
clocksource: convert ARM 32-bit down counting clocksources
clocksource: convert ARM 32-bit up counting clocksources
clocksource: add common mmio clocksource
ARM: update sa1100 to reflect PXA updates
ARM: omap1: convert to using readl/writel instead of volatile struct
ARM: omap1: delete useless interrupt handler
ARM: s5p: consolidate selection of timer register
ARM: 6939/1: fix missing 'cpu_relax()' declaration
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This fixes a regression on high clock speeds with the MMCI on
ux500. We need to make sure we derive the passthru clock on the
falling edge of the incoming clock if it shall work at high
frequencies, and on the ux500's there is a special bit for this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mmci.h header contained a few registers not clearly marked
as ST Micro only, rectify this and remove the HWFC magic in the
process. The idea is to make the mmci.h header file more ordered
so other vendors with PL180 derivates can see where to put in
their custom register defines.
Includes portions of an earlier patch from Sebastian Rasmussen.
Acked-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Saves about 50KB of data.
Old/new size of all objects:
text data bss dec hex filename
563015 80096 130684 773795 bcea3 (TOTALS)
610916 32256 130632 773804 bceac (TOTALS)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be> (for drivers/net/can/softing/softing_cs.c)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
It seems that under certain circumstances the sdhci_tasklet_finish()
call can be entered with mrq set to NULL, causing the system to crash
with a NULL pointer de-reference.
Seen on S3C6410 system. Based on a patch by Dimitris Papastamos.
Reported-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
It seems that under certain circumstances that the sdhci_tasklet_finish()
call can be entered with mrq->cmd set to NULL, causing the system to crash
with a NULL pointer de-reference.
Unable to handle kernel NULL pointer dereference at virtual address 00000000
PC is at sdhci_tasklet_finish+0x34/0xe8
LR is at sdhci_tasklet_finish+0x24/0xe8
Seen on S3C6410 system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The aggressive clock gating for TMIO MMC patch has broken switching
interface power on, using MFD or platform callbacks. Restore the
ios->power_mode == MMC_POWER_UP && ios->clock == 0 case handling.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently there is a race in the MMC core between a card-detect
rescan work and the clock-gating work, scheduled from a command
completion. Fix it by removing the dedicated clock-gating mutex
and using the MMC standard locking mechanism instead.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Either OMAP_MMC_STAT_CARD_ERR or OMAP_MMC_STAT_END_OF_CMD might fire
if there is no host->cmd pointer.
Check for a valid host->cmd pointer before calling mmc_omap_cmd_done().
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes a cosmetic bug that affects printk() for SD-combo cards.
Reported-by: Prashanth Bhat <prashanth.bhat@manipal.net>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
If pci_ioremap_bar() fails during probe, we "goto release;" and free the
host, but then we return 0 -- which tells sdhci_pci_probe() that the probe
succeeded. Since we think the probe succeeded, when we unload sdhci we'll
go to sdhci_pci_remove_slot() and it will try to dereference slot->host,
which is now NULL because we freed it in the error path earlier.
The patch simply sets ret appropriately, so that sdhci_pci_probe() will
detect the failure immediately and bail out.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
mmc: tmio_mmc: Move some defines into a shared header
mmc: tmio: support aggressive clock gating
mmc: tmio: fix power-mode interpretation
mmc: tmio: remove work-around for unmasked SDIO interrupts
sh: fix SDHI IO address-range
ARM: mach-shmobile: fix SDHI IO address-range
mmc: tmio: only access registers above 0xff, if available
mfd: remove now redundant sh_mobile_sdhi.h header
sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
mmc: tmio: split core functionality, DMA and MFD glue
mmc: tmio: use PIO for short transfers
mmc: tmio-mmc: Improve DMA stability on sh-mobile
mmc: fix mmc_app_send_scr() for dma transfer
mmc: sdhci-esdhc: enable esdhc on imx53
mmc: sdhci-esdhc: use writel/readl as general APIs
mmc: sdhci: add the abort CMDTYPE bits definition
...
Fix build breakage on platforms, not providing readsw and writesw
functions, e.g., on x86(_64).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Also add TMIO_BBS.
This allows these defines to also be used by zboot.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The power-mode sequence on MMC is MMC_POWER_OFF -> MMC_POWER_UP ->
MMC_POWER_ON and not MMC_POWER_ON -> MMC_POWER_UP, as the driver currently
is implying.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO IRQs got unmasked on sh-mobile while writing to the
CTL_CLK_AND_WAIT_CTL register, because that register at address 0x138
is not implemented on those SoCs and writes to it overwrite the
register at address 0x38: CTL_SDIO_IRQ_MASK. Previous patches
eliminated access to register above 0xff on sh-mobile, so that this
work-around isn't needed anymore.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Not all tmio implementations have registers above oxff. Accessing
them on thise platforms is dangerous. In some cases it leads to
address wrapping to addresses below 0x100, which corrupts random
unrelated registers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On sh-mobile platforms the SDHI driver was using the tmio_mmc SD/SDIO
MFD cell driver. Now that the tmio_mmc driver has been split into a
core and a separate MFD glue, we can support SDHI natively without the
need to emulate an MFD controller. This also allows to support systems
with an on-SoC SDHI controller and a separate MFD with a TMIO core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
TMIO MMC chips contain an SD / SDIO IP core from Panasonic, similar to
the one, used in MN5774 and other MN57xx controllers. These IP cores are
included in many multifunction devices, in sh-mobile chips from Renesas,
in the latter case they can also use DMA. Some sh-mobile implementations
also have some other specialities, that MFD-based solutions don't have.
This makes supporting all these features in a monolithic driver inconveniet
and error-prone. This patch splits the driver into 3 parts: the core,
the MFD glue and the DMA support. In case of a modular build, two modules
will be built: mmc_tmio_core and mmc_tmio.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch allows transferring of some requests in PIO and some in DMA
mode and defaults to using DMA only for transfers longer than 8 bytes.
This is especially useful with SDIO, which can have lots of 2- and 4-byte
transfers, creating unnecessary high overhead, when executed in DMA.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some SDHI tmio implementations the order of DMA and command completion
interrupts swaps, which leads to malfunction. This patch postpones
DMA activation until the MMC command completion IRQ time.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is based on the commit "af51715079e7fb6b290e1881d63d815dc4de5011":
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
The driver may invalidate the mmc_card->csd when host driver uses dma.
So this subroutine also needs a kmalloc buffer.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the NO INT in the Multi-BLK IO in SD/MMC, and Multi-BLK read in
SDIO on imx53.
The CMDTYPE of the CMD register (offset 0xE) should be set to "11"
when the STOP CMD12 is issued on imx53 to abort one open ended
multi-blk IO. Otherwise the TC INT wouldn't be generated.
In exact block transfer, the controller doesn't complete the
operations automatically as required at the end of the transfer
and remains on hold if the abort command is not sent on imx53.
As a result, the TC flag is not asserted and SW receives timeout
exception. Set bit1 of Vendor Spec register to fix it.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add one flag to indicate the GPIO CD/WP is enabled or not
on imx platforms, and reuse the writel/readl as the general
APIs for imx SOCs.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add the abort CMDTYPE bits definition of command register (offset 0xE)
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci-esdhc-imx does not need SDHCI_QUIRK_NO_CARD_NO_RESET.
Make it OF-specific.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since these are the headers that provide irq_of_parse_and_map()
and NO_IRQ.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Chris Ball <cjb@laptop.org>
New IO FPGA implementation for Versatile Express boards contain
MMCI (PL180) cell with FIFO extended to 128 words (512 bytes).
Matt Waddel reports that this patch improves MMC performance on
his vexpress system, and also fixes "mmcblk0: error -5 transferring
data" errors.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Matt Waddel <matt.waddel@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses the fixed burst bit when using an internal DMA controller.
I found increased performance with IDMAC when this bit is set.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SDHCI driver uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
it was not converted by commit 44c10138fd
(PCI: Change all drivers to use pci_device->revision). The newer VIA
driver has similar code too. This patch converts both drivers to use
the 'revision' field of 'struct pci_dev'.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes:
drivers/mmc/card/mmc_test.c: In function ‘mmc_test_seq_perf’:
drivers/mmc/card/mmc_test.c:1878:28: warning: variable ‘ts’ set but not
used [-Wunused-but-set-variable]
There's no reason to be calling timespec_sub() here, because
mmc_test_print_avg_rate() is going to do that itself.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
This silences warnings such as
drivers/video/tmiofb.c: In function 'tmiofb_hw_init':
drivers/video/tmiofb.c:270: warning: initialization discards qualifiers from pointer target type
These were added by me in commit 2a79bb1d.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use mfd_data for passing information from mfd drivers to mfd
clients. The mfd_cell's driver_data field is being phased out.
Clients that were using driver_data now access .mfd_data
via mfd_get_data(). This changes tmio-mmc only; mfd drivers with
other cells are not modified.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No need to explicitly set the cell's platform_data/data_size.
Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (53 commits)
mmc: dw_mmc: support mmc power control with regulator
mmc: dw_mmc: fix suspend/resume operation
mmc: dw_mmc: add quirks for unreliable card detect, and capabilities
mmc: tmio: fix address in kunmap_atomic() calls
mmc: core: reset card voltage after power off
mmc: core: export function mmc_do_release_host()
mmc: sdio: remember new card RCA when redetecting card
mmc: dw_mmc: Remove set-but-unused variable.
mmc: sdhci-esdhc-imx: add card detect on custom GPIO for mx25/35
mmc: sdhci-esdhc: broken card detection is not a default quirk
mmc: sdhci-esdhc-imx: add write protect on custom GPIO on mx25/35
mmc: msm_sdcc: remove needless cache flush after dma_unmap_sg()
mmc: sh_mmcif: support aggressive clock gating
mmc: check if mmc cards < 2GB do sector addressing
mmc: core: comment on why sdio_reset is done at init time
mmc: dw_mmc: support DDR mode
mmc: via-sdmmc: Remove set-but-unused variable.
mmc: cb710: Return err value in cb710_wait_while_busy()
mmc: sdhci-pci: Remove set-but-unused variable.
mmc: mxs-mmc: add mmc host driver for i.MX23/28
...
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/dw_spi: move dw_spi.h into drivers/spi
spi/dw_spi: Fix missing header
gpio/langwell: Clear edge bit before handling
gpio/langwell: Simplify demux loop
gpio/langwell: Convert irq name space
gpio/langwell: Fix broken irq_eoi change.
gpio; Make Intel chipset gpio drivers depend on x86
gpio/cs5535-gpio: Fix section mismatch
spi/rtc-{ds1390,ds3234,m41t94}: Use spi_get_drvdata() for SPI devices
spi/davinci: Support DMA transfers larger than 65535 words
spi/davinci: Use correct length parameter to dma_map_single calls
gpio: Use __devexit at necessary places
gpio: add MODULE_DEVICE_TABLE to pch_gpio and ml_ioh_gpio
gpio/mcp23s08: support mcp23s17 variant
of_mmc_spi: add card detect irq support
spi/omap_mcspi: catch xfers of non-multiple SPI word size
spi/omap_mcspi: Off-by-one error in finding the right divisor
gpio/pca953x: Fix wrong pointer type
spi/pl022: rid dangling labels
spi: add support for SuperH SPI
...
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
* 'for-linus' of git://codeaurora.org/quic/kernel/davidb/linux-msm: (46 commits)
msm: scm: Check for interruption immediately
msm: scm: Fix improper register assignment
msm: scm: Mark inline asm as volatile
msm: iommu: Enable HTW L2 redirection on MSM8960
msm: iommu: Don't read from write-only registers
msm: iommu: Remove dependency on IDR
msm: iommu: Use ASID tagging instead of VMID tagging
msm: iommu: Rework clock logic and add IOMMU bus clock control
msm: iommu: Clock control for the IOMMU driver
msm: mdp: Set the correct pack pattern for XRGB/ARGB
msm_fb: Fix framebuffer console
msm: mdp: Add support for RGBX 8888 image format.
video: msmfb: Put the partial update magic value into the fix_screen struct.
msm: clock: Migrate to clkdev
msm: clock: Remove references to clk_ops_pcom
msm: headsmp.S: Fix section mismatch
msm: Use explicit GPLv2 licenses
msm: iommu: Enable IOMMU support for MSM8960
msm: iommu: Generalize platform data for multiple targets
msm: iommu: Create a Kconfig item for the IOMMU driver
...
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
This patch adds support for power regulators.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is related to re-init processing on suspend/resume.
When card is resuming, some register is reset. If card is removable,
maybe controller should be rescan for card. But if assume card is
non-removable, need to restore the old value at registers.
We store the value of FIFOTH at probe time and then restore it in
dw_mci_resume().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds quirks and capabilities to platdata.
Some cards don't use the CDn pin; in that case, we assume the card's
inserted. Some boards need other capabilities. So, we add capabilities
in the board's platdata.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently kunmap_atomic() doesn't take into account the offset, used
with kmap_atomic(). On platforms, where kunmap_atomic() is not a NOP,
this will lead to problems, when offset != 0.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
At power off, reset OCR mask to be the highest possible voltage
supported for the current mmc host.
This solves the re-initialization during the power up sequence.
The voltage may have been decreased due to the card accepts a lower
voltage than the voltage used during the initialization sequence.
We need to reset the voltage to by the host highest possible value
since according to specification the initialization must always be
done at high voltage.
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When using mmc_try_claim_host the corresponding release
function is mmc_do_release_host, which then also must
be exported.
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
During redetection of a SDIO card, a request for a new card RCA
was submitted to the card, but was then overwritten by the old RCA.
This caused the card to be deselected instead of selected when using
the incorrect RCA. This bug's been present since the "oldcard"
handling was introduced in 2.6.32.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Reviewed-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Pawel Wieczorkiewicz <pawel.wieczorkiewicz@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
count is only ever used by assigning to old_len if count == 0, and
then old_len isn't ever used at all. So, both are redundant. Fixes:
drivers/mmc/host/dw_mmc.c: In function ‘dw_mci_read_data_pio’:
drivers/mmc/host/dw_mmc.c:1034:32: warning: variable ‘old_len’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Marc Reilly <marc@cpdesign.com.au>
Tested-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It can be worked around using a GPIO which will be done for i.MX later.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tested-by: Marc Reilly <marc@cpdesign.com.au>
Tested-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Marc Reilly <marc@cpdesign.com.au>
Tested-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
dma_unmap_sg() already flushes the cache, I don't get what this
code is doing here.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (76 commits)
pch_uart: reference clock on CM-iTC
pch_phub: add new device ML7213
n_gsm: fix UIH control byte : P bit should be 0
n_gsm: add a documentation
serial: msm_serial_hs: Add MSM high speed UART driver
tty_audit: fix tty_audit_add_data live lock on audit disabled
tty: move cd1865.h to drivers/staging/tty/
Staging: tty: fix build with epca.c driver
pcmcia: synclink_cs: fix prototype for mgslpc_ioctl()
Staging: generic_serial: fix double locking bug
nozomi: don't use flush_scheduled_work()
tty/serial: Relax the device_type restriction from of_serial
MAINTAINERS: Update HVC file patterns
tty: phase out of ioctl file pointer for tty3270 as well
tty: forgot to remove ipwireless from drivers/char/pcmcia/Makefile
pch_uart: Fix DMA channel miss-setting issue.
pch_uart: fix exclusive access issue
pch_uart: fix auto flow control miss-setting issue
pch_uart: fix uart clock setting issue
pch_uart : Use dev_xxx not pr_xxx
...
Fix up trivial conflicts in drivers/misc/pch_phub.c (same patch applied
twice, then changes to the same area in one branch)
To support MMC aggressive clock gating the driver has to stop the
interface clock when the .set_ios() method is called with .clock == 0.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some TOSHIBA MMC cards only support sector addressing even though the
size is < 2GB. According to JEDEC Spec JESD84-A441-1 the ocr register
(bits 30, 29) determine byte/sector mode. Use them.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdio_reset sends a CMD52 to reset the sdio card. This is highly
recommended for sdio cards being reinitialized. Since we do not
know if the card is being reinitialized we just send the command.
SD/eMMC cards are supposed to ignore the CMD before the CMD0.
Document why we are doing this.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86: Clean up apic.c and apic.h
x86: Remove superflous goal definition of tsc_sync
x86: dt: Correct local apic documentation in device tree bindings
x86: dt: Cleanup local apic setup
x86: dt: Fix OLPC=y/INTEL_CE=n build
rtc: cmos: Add OF bindings
x86: ce4100: Use OF to setup devices
x86: ioapic: Add OF bindings for IO_APIC
x86: dtb: Add generic bus probe
x86: dtb: Add support for PCI devices backed by dtb nodes
x86: dtb: Add device tree support for HPET
x86: dtb: Add early parsing of IO_APIC
x86: dtb: Add irq domain abstraction
x86: dtb: Add a device tree for CE4100
x86: Add device tree support
x86: e820: Remove conditional early mapping in parse_e820_ext
x86: OLPC: Make OLPC=n build again
x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
x86: OLPC: Cleanup config maze completely
x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
...
Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
This patch adds DDR mode support to dw_mmc.
If we set any bit in UHS_REG bit[16:31], the card of that slot is
supported for DDR mode. For example, if UHS_REG[16] is set, card
number 0 is DDR mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
drivers/mmc/host/via-sdmmc.c: In function ‘via_reset_pcictrl’:
drivers/mmc/host/via-sdmmc.c:805:8: warning: variable ‘addrbase’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Harald Welte <HaraldWelte@viatech.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Fixes:
drivers/mmc/host/cb710-mmc.c: In function ‘cb710_wait_while_busy’:
drivers/mmc/host/cb710-mmc.c:182:6: warning: variable ‘err’ set but not
used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
drivers/mmc/host/sdhci-pci.c: In function ‘sdhci_pci_probe_slot’:
drivers/mmc/host/sdhci-pci.c:913:18: warning: variable ‘addr’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This adds the mmc host driver for Freescale MXS-based SoC i.MX23/28.
The driver calls into mxs-dma via generic dmaengine api for both pio
and data transfer.
Thanks Chris Ball for the indentation patch.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This switches the mxcmmc driver to use the dmaengine API. Unlike
the old one this one is always present in the tree, even if no DMA
is implemented, hence we can remove all the #ifdefs in from the driver.
The driver automatically switches to PIO mode if no DMA support or no
suitable channel is available.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for 8-bit buswidth.
dw_mmc can use 8-bit buswidth and set to CTYPE_8BIT in card-type register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the new dmaengine helper functions, and drop the error check
on the returned cookier from the dmaengine - we recently
established that this is really not allowed to fail.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This variable doesn't seem to be used for anything after the
other patches so just drop it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the DMA-API you shall unmap the sglists with the same
sglist length as passed into the mapping function, not the
returned value from the mapping function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the new dmaengine helper functions, and drop the error check
on the returned cookier from the dmaengine - we recently
established that this is really not allowed to fail.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The host_sglen is now actually used to keep track of whether DMA
is active or not, so rename and retype it to bool.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the DMA-API you shall unmap the sglists with the same
sglist length as passed into the mapping function, not the
returned value from the mapping function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the new dmaengine helpers to make the code more readable.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes the following:
- It is perfectly legal for the dma_map_sg() to return fewer
entries than were passed in.
- Supply the returned numer of (possibly coalesced) entries to
the device_pre_slave_sg() function.
- Use the proper original sg_len when unmapping the sglist
in the error path.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
So we know the implementation and prototypes agree with each other.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The test file is created under debugfs, not sysfs. Also remove
the unnecessary default n.
Signed-off-by: Will Newton <will.newton@imgtec.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Setting this bit in the clock enable register will stop the clock
when the card is in the IDLE state.
Signed-off-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We need to run the card detect tasklet at the end of slot initialisation
as it is possible that a card has been inserted prior to boot, so we don't
see an insertion interrupt and now the card is sitting there inserted but
with no power to it.
Signed-off-by: Neil Jones <neil.jones@imgtec.com>
Signed-off-by: Will Newton <will.newton@imgtec.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently MMC_MXC driver can be selected by all i.MX devices.
Restrict its use only for the appropriate processors.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add two large sequential I/O performance tests:
35. Large sequential read into scattered pages
36. Large sequential write from scattered pages
The tests measure transfer times for 10MiB, 100MiB, 1000MiB.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Existing performance tests measure single or sequential I/O speed.
Add two random I/O tests:
33. Random read performance by transfer size
34. Random write performance by transfer size
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The test area size was set to the preferred erase size but for comparison
purposes it is better if it is the same size for different devices. Make
it a multiple of preferred erase size that is greater than or equal to 4MiB.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This sdio card supports having its sdio clock shutdown.
It is also not using the SDIO IRQ, but rather uses a side gpio irq.
Signed-off-by: Pierre Tardy <tardyp@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some sdio card are not following sdio standard, and do not work
when the sdio bus's clock is gated.
To keep functionnality for all legacy driver, we turn this quirk on
for every sdio card.
Drivers needs to disable the quirk manually when someone verifies that
their supported card works with clock gating.
Signed-off-by: Pierre Tardy <tardyp@gmail.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some cards have quirks valid for every platforms using current
platform quirk hooks leads to a lot of code and debug duplication.
So we inspire a bit from what exists in PCI subsystem and do our own
per vendorid/deviceid quirk. We still drop the complexity of the pci
quirk system (with special section tables, and so on).
That can be added later if needed.
Signed-off-by: Pierre Tardy <pierre.tardy@intel.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since mmc clock gating can also be used as a power gating
tip, it's better to put the led blinking after having
ungated the clock.
Signed-off-by: Pierre Tardy <pierre.tardy@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the MMC host controller does not support waiting for card signaling
busy state (MMC_CAP_WAIT_WHILE_BUSY cap), there is no point in prining
the relevant warning message.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Samsung SDHCI host controller supports the Auto CMD12.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
While the MMC handled the card's read only flag correctly on open,
it did not setup the flag in the allocated disk structure. The
consequence being that probing the /sys/class/block/mmcblkX/ro
attribute always reported 0.
Signed-off-by: Marc-Andre Hebert <hebert.marcandre@gmail.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enhanced area feature is a new feature defined in eMMC4.4 standard. This
user data area provides higher performance/reliability, at the expense
of using twice the effective media space due to the area using SLC.
The MMC driver now reads out the enhanced area offset and size and adds
them to the device attributes in sysfs. Enabling the enhanced area can
only be done once, and should be done in manufacturing. To use this
feature, bit ERASE_GRP_DEF should also be set.
Documentation/ABI/testing/sysfs-devices-mmc describes the two new
attributes.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
30201e7f3 ("mmc: skip detection of nonremovable cards on rescan")
allowed skipping detection of nonremovable cards on mmc_rescan().
The intention was to only skip detection of hardwired cards that
cannot be removed, so make sure this is indeed the case by directly
checking for (lack of) MMC_CAP_NONREMOVABLE, instead of using
mmc_card_is_removable(), which is overloaded with
CONFIG_MMC_UNSAFE_RESUME semantics.
The user-visible symptom of the bug this patch fixes is that no
"mmc: card XXXX removed" message appears in dmesg when a card is
removed and CONFIG_MMC_UNSAFE_RESUME=y.
Reported-and-tested-by: Dmitry Shmidt <dimitrysh@google.com>
Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This fixes a bug introduced by 807e8e4067 ("mmc: Fix sd/sdio/mmc
initialization frequency retries") that prevented SDIO drivers from
performing SDIO commands in their probe routines -- the above patch
called mmc_claim_host() before sdio_add_func(), which causes a deadlock
if an external SDIO driver calls sdio_claim_host().
Fix tested on an OLPC XO-1.75 with libertas on SDIO.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Reviewed-and-Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The code path entered via mmc_host_enable() can include register
accesses to the HSMMC IP block. For this to work, both the device
interface clock and functional clock need to be enabled before
mmc_host_enable() is called. However, omap_hsmmc_probe() calls
mmc_host_enable() before enabling the device interface clock.
Fix by calling mmc_host_enable() after the device interface clock is
enabled.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Madhusudhan Chikkature Rajashekar <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Tero Kristo <Tero.Kristo@nokia.com>
Acked-by: Madhusudhan Chikkature Rajashekar <madhu.cr@ti.com>
Modifying the device & driver name from "mmci-omap-hs" to
"omap_hsmmc".
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP2420 platform consists of mmc block as in omap1 and not the
hsmmc block as present in omap2430, omap3, omap4 platforms.
Removing all base address macro defines except keeping one for OMAP2420 and
adapting only hsmmc device registration and driver to hwmod framework.
Changes involves:
1) Remove controller reset in devices.c which is taken care of
by hwmod framework.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute.
3) Update the driver to use dev_attr to find whether controller
supports dual volt cards
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Reviewed-by: Balaji T K <balajitk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Final step to eliminate of_platform_bus_type. They're all just
platform drivers now.
v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP4 supports up to 5 MMC controllers, but only 3 of these were
initialized. MMC5 is used by wl12xx chip. So initialize MMC4 and MMC5.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Doing tiocmget was such fun we should do tiocmset as well for the same
reasons
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't actually need this and it causes problems for internal use of
this functionality. Currently there is a single use of the FILE * pointer.
That is the serial core which uses it to check tty_hung_up_p. However if
that is true then IO_ERROR is also already set so the check may be removed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch from Linus Walleij.
Add dmaengine based support for DMA to the MMCI driver, using the
Primecell DMA engine interface. The changes over Linus' driver are:
- rename txsize_threshold to dmasize_threshold, as this reflects the
purpose more.
- use 'mmci_dma_' as the function prefix rather than 'dma_mmci_'.
- clean up requesting of dma channels.
- don't release a single channel twice when it's shared between tx and rx.
- get rid of 'dma_enable' bool - instead check whether the channel is NULL.
- detect incomplete DMA at the end of a transfer. Some DMA controllers
(eg, PL08x) are unable to be configured for scatter DMA and also listen
to all four DMA request signals [BREQ,SREQ,LBREQ,LSREQ] from the MMCI.
They can do one or other but not both. As MMCI uses LBREQ/LSREQ for the
final burst/words, PL08x does not transfer the last few words.
- map and unmap DMA buffers using the DMA engine struct device, not the
MMCI struct device - the DMA engine is doing the DMA transfer, not us.
- avoid double-unmapping of the DMA buffers on MMCI data errors.
- don't check for negative values from the dmaengine tx submission
function - Dan says this must never fail.
- use new dmaengine helper functions rather than using the ugly function
pointers directly.
- allow DMA code to be fully optimized away using dma_inprogress() which
is defined to constant 0 if DMA engine support is disabled.
- request maximum segment size from the DMA engine struct device and
set this appropriately.
- removed checking of buffer alignment - the DMA engine should deal with
its own restrictions on buffer alignment, not the individual DMA engine
users.
- removed setting DMAREQCTL - this confuses some DMA controllers as it
causes LBREQ to be asserted for the last seven transfers, rather than
six SREQ and one LSREQ.
- removed burst setting - the DMA controller should not burst past the
transfer size required to complete the DMA operation.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to store the number of bytes transferred in our host
structure - we can store this directly in data->bytes_xfered.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to switch to data available interrupts if there's at
least half a FIFO depth worth of data remaining, as we'll still get
the FIFO half full interrupt. Keep this interrupt masked off until
we have less than half the FIFO depth worth of data remaining.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sg_miter API provides the required cache maintainence, so we don't
need to do that ourselves. Remove the unnecessary additional cache
maintainence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The data counter counts the number of bytes transferred on the MMC bus.
When a FIFO overrun occurs, we will not have transferred a FIFOs-worth
of data to memory, and so the data counter will be a FIFOs-worth ahead.
If this occurs on a block boundary, we will report one too many sectors
as successful. Fix this.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We should not report incomplete blocks on error. Return the number of
bytes successfully transferred, rounded down to the nearest block.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we encounter an error, make sure we complete the transaction
otherwise we'll leave the request dangling.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.
Search and replace the following:
ARCH_OMAP2420 SOC_OMAP2420
ARCH_OMAP2430 SOC_OMAP2430
ARCH_OMAP3430 SOC_OMAP3430
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
The MMCIDATACNT register contain the number of byte left at error
not the number of words, so loose the << 2 thing. Further if CRC
fails on the first block, we may end up with a negative number
of transferred bytes which is not good, and the formula was in
wrong order.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The bfin_sdh driver allocates the wrong size for the private data
in the mmc_host. The first parameter of mmc_alloc_host should be
the size of the local driver struct rather than the common mmc_host.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have 8-bit width support but is not a v3 controller.
So we need platform_8bit_width() to support 8-bit buswidth.
Also we need MMC_CAP_8_BIT_DATA, so we add it in platdata.
This gets 8-bit support working again on s3c, after we previously
disabled 8-bit by default on non-v3 controllers.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
clk_get() returns a struct clk cookie to the driver and some platforms
may return NULL if they only support a single clock. clk_get() has only
failed if it returns a ERR_PTR() encoded pointer.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Don't read the command response from the registers when either the
command timed out (because there was no response from the card) or
the checksum on the response was invalid.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
Including usb.h once is enough in drivers/mmc/host/ushc.c
This removes the duplicate.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ALSA: AACI: fix timeout duration
ALSA: AACI: fix timeout condition checking
ARM: 6636/1: ep93xx: default multiplexed gpio ports to gpio mode
ARM: 6637/1: Make the argument to virt_to_phys() "const volatile"
ARM: twd: ensure timer reload is reprogrammed on entry to periodic mode
ARM: 6635/2: Configure reference clock for Versatile Express timers
ARM: versatile: name configuration options after actual board names
ARM: realview: name configuration options after actual board names
ARM: realview,vexpress: fix section mismatch warning for pen_release
ARM: 6632/3: mmci: stop using the blockend interrupts
Implement a suggestion from Russell to drop the use of blockend
interrupts altogether and instead rely on the data counter.
Tested with error-free cards on U300, U8500 and RealView PB1176.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The probe function adds the MMC host which can start accepting request
immediately. There is an assumption here that no requests happen
immediatly, but it's not always the case. This assumption can causes
a BUG() when the clocks are disabled. The fix is to just remove the
clock disable in the probe function.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Remove parts of this driver which use internal API calls. This
replaces the calls as suggested by Russell King.
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Having conditional around the of_match_table and the of_node pointers
turns out to make driver code use ugly #ifdef blocks. Drop the
conditionals and remove the #ifdef blocks from the affected drivers.
Also tidy up minor whitespace issues within the same hunks.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Explicitly include err.h, of_address.h and of_irq.h.
Make use of machine_is() conditional on PPC.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (29 commits)
of/flattree: forward declare struct device_node in of_fdt.h
ipmi: explicitly include of_address.h and of_irq.h
sparc: explicitly cast negative phandle checks to s32
powerpc/405: Fix missing #{address,size}-cells in i2c node
powerpc/5200: dts: refactor dts files
powerpc/5200: dts: Change combatible strings on localbus
powerpc/5200: dts: remove unused properties
powerpc/5200: dts: rename nodes to prepare for refactoring dts files
of/flattree: Update dtc to current mainline.
of/device: Don't register disabled devices
powerpc/dts: fix syntax bugs in bluestone.dts
of: Fixes for OF probing on little endian systems
of: make drivers depend on CONFIG_OF instead of CONFIG_PPC_OF
of/flattree: Add of_flat_dt_match() helper function
of_serial: explicitly include of_irq.h
of/flattree: Refactor unflatten_device_tree and add fdt_unflatten_tree
of/flattree: Reorder unflatten_dt_node
of/flattree: Refactor unflatten_dt_node
of/flattree: Add non-boottime device tree functions
of/flattree: Add Kconfig for EARLY_FLATTREE
...
Fix up trivial conflict in arch/sparc/prom/tree_32.c as per Grant.
This patch adds support for handling SDIO interrupt on DaVinci MMC/SD
controller.
The patch has been tested on DM355 and DA850 EVMs with Marvell Libertas
based SDIO wireless LAN card.
Signed-off-by: Alagu Sankar <alagusankar@embwise.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The card is not always clocked and the clock frequency zero is perfectly
legal, thus this code in mmc_set_data_timeout() may cause a division by
zero. It will be triggered more often if you're using software clock
gating but can be triggered under other conditions too.
Reported-by: Pierre Tardy <tardyp@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
With current code card insert/eject interrupts will acknowledge outstanding
commands. Normally this seems to be no problem, however if the hardware gets
stuck and no interrupts for CMD_TIMEOUT or CMD_RESPEND are generated, then
inserting and ejecting cards will falsely acknowledge outstanding commands
from the core.
This patch changes the behavior so that CMDs are only acked, if
CMD_TIMEOUT or CMD_RESPEND is received.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
When doing excessive hotplug, e.g., repeated insert/eject operations,
the hardware may get confused to a point where no CMDTIMEOUT/CMDRESPEND
interrupts are generated any more. As a result requests get stuck, e.g.:
[ 360.351562] INFO: task kworker/u:0:5 blocked for more than 120 seconds.
[ 360.351562] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 360.359375] kworker/u:0 D c020c2b4 0 5 2 0x00000000
[ 360.367187] Backtrace:
[ 360.367187] [<c020bfb0>] (schedule+0x0/0x340) from [<c020c480>] (schedule_timeout+0x20/0x190)
[ 360.375000] r8:c702fd70 r7:00000002 r6:c702e000 r5:c702fdc4 r4:7fffffff
[ 360.375000] r3:c701e040
[ 360.382812] [<c020c460>] (schedule_timeout+0x0/0x190) from [<c020be78>] (wait_for_common+0xc4/0x150)
[ 360.390625] r6:c702e000 r5:c702fdc4 r4:7fffffff
[ 360.390625] [<c020bdb4>] (wait_for_common+0x0/0x150) from [<c020bfac>] (wait_for_completion+0x18/0x1c)
[ 360.398437] [<c020bf94>] (wait_for_completion+0x0/0x1c) from [<c0185590>] (mmc_wait_for_req+0x214/0x234)
[ 360.406250] [<c018537c>] (mmc_wait_for_req+0x0/0x234) from [<c01889d0>] (mmc_sd_switch+0xfc/0x114)
[ 360.414062] r7:c702fe4c r6:c702fe20 r5:c7179800 r4:00fffff0
[ 360.421875] [<c01888d4>] (mmc_sd_switch+0x0/0x114) from [<c0187f70>] (mmc_sd_setup_card+0x260/0x384)
[ 360.429687] [<c0187d10>] (mmc_sd_setup_card+0x0/0x384) from [<c01885e0>] (mmc_sd_init_card+0x13c/0x1e0)
[ 360.437500] [<c01884a4>] (mmc_sd_init_card+0x0/0x1e0) from [<c01887a8>] (mmc_attach_sd+0x124/0x1a8)
[ 360.445312] r8:c02db404 r7:ffffff92 r6:c702ff34 r5:c6007da8 r4:c6007c00
[ 360.453125] [<c0188684>] (mmc_attach_sd+0x0/0x1a8) from [<c0185140>] (mmc_rescan+0x248/0x2f0)
[ 360.460937] r5:c6007da8 r4:c6007c00
[ 360.468750] [<c0184ef8>] (mmc_rescan+0x0/0x2f0) from [<c00467f0>] (process_one_work+0x1ec/0x318)
[ 360.476562] r7:c6007da8 r6:00000000 r5:c710ec00 r4:c701bde0
[ 360.484375] [<c0046604>] (process_one_work+0x0/0x318) from [<c0047fb0>] (worker_thread+0x1b0/0x2cc)
[ 360.492187] [<c0047e00>] (worker_thread+0x0/0x2cc) from [<c004b338>] (kthread+0x8c/0x94)
[ 360.500000] [<c004b2ac>] (kthread+0x0/0x94) from [<c0037fc4>] (do_exit+0x0/0x590)
[ 360.507812] r7:00000013 r6:c0037fc4 r5:c004b2ac r4:c7021f00
This patch addresses this problem by introducing timeouts for outstanding
interrupts. If a hardware interrupt is missing, a soft reset will be
performed to bring the hardware back to a working state.
Tested with the SDHI hardware block in sh7372 / AP4EVB.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch implements SDIO IRQ support for mfds which
announce the TMIO_MMC_SDIO_IRQ flag for tmio_mmc.
If MMC_CAP_SDIO_IRQ is also set SDIO IRQ signalling is activated.
Tested with a b43-based wireless SDIO card and sh_mobile_sdhi.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
with "mmc: tmio: implement a bounce buffer for unaligned DMA"
gcc generates the following warnings:
drivers/mmc/host/tmio_mmc.c:654:6: warning: 'ret' may be used uninitialized in this function
drivers/mmc/host/tmio_mmc.c:730:6: warning: 'ret' may be used uninitialized in this function
This patch fixes these by setting ret to -EINVAL in the affected code paths.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
For example, with SDIO WLAN cards, some transfers happen with buffers at
odd addresses, whereas the SH-Mobile DMA engine requires even addresses
for SDHI. This patch extends the tmio driver with a bounce buffer, that
is used for single entry scatter-gather lists both for sending and
receiving. If we ever encounter unaligned transfers with multi-element
sg lists, this patch will have to be extended. For now it just falls
back to PIO in this and other unsupported cases.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
drivers/mmc/host/tmio_mmc.h is only used by drivers/mmc/host/tmio_mmc.c,
this needlessly complicates source-code handling.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Arindam Nath