Commit Graph

17 Commits

Author SHA1 Message Date
Sergei Shtylyov 42d399e418 DaVinci: remove unneeded #include's
There have accumulated quite a lot of them after the code reorganizations...

In several cases I had to replace #include <linux/dma-mapping.h> which wasn't
needed directly but happened to #include <linux/err.h> which was needed.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-11-25 10:21:31 -08:00
Kevin Hilman 5fcd294df2 davinci: remove watchdog from soc_info
watchdog info is not needed in soc_info, platform_device can
be used directly in core code.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:57 +03:00
David Griego a23f7dc82d davinci: Fix watchdog reset code
The davinci reset routine, davinci_watchdog_reset(), sets the
TCR register instead of the TGCR register as it should to put
the WDT into its "Initial State".

It also writes the WDTCR register without the proper WDKEY
which is pointless since the register will be write-protected.

Signed-off-by: David Griego <dgriego@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:56 +03:00
Mark A. Greer 5570078c0e davinci: Move PINMUX defines to SoC files
Different SoC have different numbers of pinmux registers and other
resources that overlap with each other.  To clean up the code and
eliminate defines that overlap with each other, move the PINMUX
defines to the SoC specific files.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-05-28 15:17:48 -07:00
Mark A. Greer 3abd5acfff davinci: Add compare register support to timer code
The Timer64p timer has 8 compare registers that can
be used to generate interrupts when the timer value
matches the compare reg's value.  They do not disturb
the timer itself.  This can be useful when there is
only one timer available for both clock events and
clocksource.

When enabled, the clocksource remains a continuous
32-bit counter but the clock event will no longer
support periodic interrupts.  Instead only oneshot
timers will be supported and implemented by setting
the compare register to the current timer value plus
the period that the clock event subsystem is requesting.

Compare registers support is enabled automatically
when the following conditions are met:
1) The same timer is being used for clock events
   and clocksource.
2) The timer is the bottom half (32 bits) of the
   64-bit timer (hardware limitation).
3) The the compare register offset and irq are
   not zero.

Since the timer is always running, there is a hardware
race in timer32_config() between reading the current
timer value, and adding the period to the current
timer value and writing the compare register.
Testing on a da830 evm board with the timer clocked
at 24 MHz and the processor clocked at 300 MHz,
showed the number of counter ticks to do this ranged
from 20-53 (~1-2.2 usecs) but usually around 41 ticks.
This includes some artifacts from collecting the
information.  So, the minimum period should be
at least 5 usecs to be safe.

There is also an non-critical lower limit that
the period should be since there is no point in
setting an event that is much shorter than the
time it takes to set the event, and get & handle
the timer interrupt for that event.  There can
also be all sorts of delays from activities
occuring elsewhere in the system (including
hardware activitis like cache & TLB management).
These are virtually impossible to quantify so a
minimum period of 50 usecs was chosen.  That will
certianly be enough to avoid the actual hardware
race but hopefully not large enough to cause
unreasonably course-grained timers.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-05-28 15:17:48 -07:00
Mark A. Greer 951d6f6d70 davinci: Add watchdog base address flexibility
The watchdog code currently hardcodes the base address
of the timer its using.  To support new SoCs, make it
support timers at any address.  Use the soc_info structure
to do this.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-05-26 08:20:31 -07:00
Mark A. Greer f64691b3ab davinci: Add base address and timer flexibility
The davinci timer code currently hardcodes the timer register
base addresses, the timer irq numbers, and the timers to use
for clock events and clocksource.  This won't work for some
a new SoC so put those values into the soc_info structure
and set them up in the SoC-specific files.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-05-26 08:19:04 -07:00
Kevin Hilman fb6313879c davinci: add platform support for watchdog timer
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-05-26 07:18:15 -07:00
Kevin Hilman e60990023c davinci: timers: use clk_get_rate()
Use clock framework instead of hard-coded CLOCK_TICK_RATE for
determining timer tick frequencies.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-04-27 09:49:36 -07:00
Kevin Hilman f5c122da54 davinci: add arch_ioremap() which uses existing static mappings
Add arch-specific ioremap() which uses any existing static mappings in
place of doing a new mapping.  From now on, drivers should always use
ioremap() instead of IO_ADDRESS().

In addition, remove the davinci_[read|write]* macros in favor of using
ioremap.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-04-23 09:31:09 -07:00
Magnus Damm 8e19608e8b clocksource: pass clocksource to read() callback
Pass clocksource pointer to the read() callback for clocksources.  This
allows us to share the callback between multiple instances.

[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-21 13:41:47 -07:00
Rusty Russell 320ab2b0b1 cpumask: convert struct clock_event_device to cpumask pointers.
Impact: change calling convention of existing clock_event APIs

struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.

Another single-patch change.  For safety, we BUG_ON() in
clockevents_register_device() if it's not set.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
2008-12-13 21:20:26 +10:30
Russell King fced80c735 [ARM] Convert asm/io.h to linux/io.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-06 12:10:45 +01:00
Russell King a09e64fbc0 [ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
This just leaves include/asm-arm/plat-* to deal with.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-07 09:55:48 +01:00
Russell King be50972935 [ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-07 09:40:08 +01:00
Thomas Gleixner 18de5bc4c1 clockevents: fix resume logic
We need to make sure, that the clockevent devices are resumed, before
the tick is resumed. The current resume logic does not guarantee this.

Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock
event devices before resuming the tick / oneshot functionality.

Fixup the existing users.

Thanks to Nigel Cunningham for tracking down a long standing thinko,
which affected the jinxed VAIO.

[akpm@linux-foundation.org: xen build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-21 17:49:15 -07:00
Kevin Hilman 7c6337e225 [ARM] 4303/3: base kernel support for TI DaVinci
Add base kernel support for the TI DaVinci platform.

This patch only includes interrupts, timers, CPU identification,
serial support and basic power and sleep controller init.  More
drivers to come.

Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-11 17:26:55 +01:00